diff --git a/README.md b/README.md
index 35d8c0f..84c28e8 100644
--- a/README.md
+++ b/README.md
@@ -52,19 +52,29 @@ BMBurner is a Arduino based EPROM Programmer that can Read/Write/Verify Chips (2
 - Edit Reading/Writing Buffer addressing
 - Much Mores...
 
-# Serial Protocol Functions :
+# Serial Protocol Functions (for developpers) :
 
 | Command | Receice Buffer | Description
 | --- | --- | --- |
-| 'C' + R + 'S' + "MSB" + "LSB" + "CS"| "B1" + "B2" + "...BX" + "CS" | Reads 'S' bytes(S=Size, S=0 for 256bytes) from the EEPROM at address "MSB" + "LSB" (C=Chip, C=2 for 27C256, etc, C=5 for 27SF512 SST, etc) |
-| 'C' + W + 'S' + "MSB" + "LSB" + "B1" + "B2" + "..." + "CS" | "O" (0x4F) | Writes 'S' bytes(S=Size, S=0 for 256bytes) from the EEPROM at address "MSB" + "LSB" (C=Chip, C=2 for 27C256, etc, C=5 for 27SF512 SST, etc) |
-| 5 + E + "CS" | "O" (0x4F) | Erase all the data on Chip Type 5 (SST) |
-| V + CS (V+V) | "B1" + "B2" + "B3" | Prints the version bytes of the BMBurner PCB Board for Moates Compatibility(Ex:V5.1.0) |
-| F + CS (F+F) | "B1" + "B2" | Prints the firmware bytes of the BMBurner PCB Board(Ex:V2.0) |
-| G + CS (G+G) | "B1" + "B2" | Prints the BMBurner Starting baudrate (Ex:'B1=1,baud 921.6k', 'B1=2,baud 9600', 'B1=3,baud 115200') |
-| S + 0 + S | "O" (0x4F) | Switch the internal baudrate on the BMBurner to 921600 for Moates Compatibility |
-| S + 7 + S | "O" (0x4F) | Switch the internal baudrate on the BMBurner to 115600 for Moates Compatibility |
-| A + 'N' | "O" (0x4F) | Change the chip AccessTime to 'N'ns (Ex:N=70 for 70ns AccessTime) |
+| 'C'+R+'S'+'MSB'+'LSB'+'CS'| "B1"+"B2"+"...BX"+"CS" | Reads 'S' bytes(S=Size, S=0 for 256bytes) from the EEPROM at address 'MSB'+'LSB' (C=Chip, C=2 for 27C256, C=5 for 27SF512 SST) |
+| 'C'+W+'S'+'MSB'+'LSB'+'B1'+'B2'+'...BX'+'CS'|"O"(0x4F) | Writes 'S' bytes(S=Size, S=0 for 256bytes) from the EEPROM at address 'MSB'+'LSB' (C=Chip, C=2 for 27C256, C=5 for 27SF512 SST) |
+| 5+E+'CS' | "O"(0x4F) | Erase all the data on Chip Type 5 (SST) |
+| V+'CS' (V+V) | "B1"+"B2" + "B3" | Prints the version bytes of the BMBurner PCB Board for Moates Compatibility(Ex:V5.1.0) |
+| F+'CS' (F+F) | "B1"+"B2" | Prints the firmware bytes of the BMBurner PCB Board(Ex:V2.0) |
+| G+'CS' (G+G) | "B1"+"B2" | Prints the BMBurner Starting baudrate (Ex:'B1=1,baud 921.6k', 'B1=2,baud 9600', 'B1=3,baud 115200') |
+| S+0+S | "O"(0x4F) | Switch the internal baudrate on the BMBurner to 921600 for Moates Compatibility |
+| S+7+S | "O"(0x4F) | Switch the internal baudrate on the BMBurner to 115600 for Moates Compatibility |
+| A+'N' | "O"(0x4F) | Change the chip AccessTime to 'N'ns (Ex:N=70 for 70ns AccessTime) |
+
+| Command | Descriptor
+| --- | --- |
+| 'N' | 'N' equal the AccessTime in ns (Ex:N=70 for 70ns AccessTime) |
+| 'MSB' | 'MSB' equal to the Most Signifiant Byte for the EEPROM Address location |
+| 'LSB' | 'LSB' equal to the Least Signifiant Byte for the EEPROM Address location |
+| 'C' | 'C' equel the Chip Type (C=2 for 27C256, C=5 for 27SF512 SST, etc..) |
+| 'S' | 'S' equal the Size/Amount of bytes to proceed (S=0 is for 256bytes else S equal the amount of byte, S=1 for 1byte) |
+| 'CS' | 'CS' equal to the checksum of the Commands we are sending in 1Byte form |
+| ... | Any Command that isn't within 'Brackets' are the actual Char/String to send (ex: V is for sending the Char V |
 
 # Donations :