diff --git a/reference/speeduino.ini b/reference/speeduino.ini
index 05478134..c953b8fa 100644
--- a/reference/speeduino.ini
+++ b/reference/speeduino.ini
@@ -326,7 +326,7 @@ page = 1
       reqFuel       = scalar, U08,      24,        "ms",        0.1,       0.0,   0.0,    25.5,      1
       divider       = scalar, U08,      25,        "",          1.0,       0.0
       alternate     = bits,   U08,      26, [0:0], "Simultaneous", "Alternating"
-      multiplyMAP1  = bits,   U08,      26, [1:1], "No",       "Yes"
+      crkngAddCLTAdv= bits,   U08,      26, [1:1], "No",       "Yes"
       includeAFR    = bits,   U08,      26, [2:2], "No",       "Yes"
       hardCutType   = bits,   U08,      26, [3:3], "Full",      "Rolling"
       ignAlgorithm  = bits,   U08,      26, [4:6], $loadSourceNames
@@ -2167,6 +2167,7 @@ menuDialog = main
   ignBypassPin    = "The ARDUINO pin that the ignition bypass is connected to. This is NOT the pin on the connector, but the pin it relates to on the arduino"
   ignBypassEnable = "If turned on, a ground signal will be output during cranking on the specified pin. This is used to bypass the Speeduino ignition control during cranking."
   ignCranklock    = "On certain low resolution ignition patterns, the cranking timing can be locked to occur when a pulse is received."
+  crkngAddCLTAdv  = "Adds cold advance values to cranking angle."
 
   multiplyMAP     = "If enabled, the MAP reading is included directly into the pulsewidth calculation by multiplying the VE lookup value by either the MAP:Baro ratio or MAP/100.\n This results in a flatter VE table that can be easier to tune in some instances. The MAP/100 option is generally used for compatibility with fuel tables from other ECUs. MAP:Baro ratio is recommended for new tunes. \n VE table must be retuned when this value is changed."
   legacyMAP       = "Use the legacy method of reading the MAP sensor that was used prior to the 201905 firmware. This should ONLY be enabled if you are upgrading from a firmware earlier than this"
@@ -2789,6 +2790,7 @@ menuDialog = main
 
     dialog = crankingIgnOptions, "Cranking Timing", yAxis
         field = "Cranking advance Angle",       CrankAng,       { ignCranklock == 0 }
+        field = "Add cold advance",    crkngAddCLTAdv,          { ignCranklock == 0 }
         field = "Cranking bypass", ignBypassEnable
         field = "Bypass output pin", ignBypassPin               { ignBypassEnable }
         field = "Fix cranking timing with trigger", ignCranklock,   { TrigPattern == 1 || TrigPattern == 4 || TrigPattern == 10 || TrigPattern == 9 }
diff --git a/speeduino/corrections.ino b/speeduino/corrections.ino
index 0c3a38e2..dfdfef22 100644
--- a/speeduino/corrections.ino
+++ b/speeduino/corrections.ino
@@ -723,7 +723,11 @@ int8_t correctionFixedTiming(int8_t advance)
 int8_t correctionCrankingFixedTiming(int8_t advance)
 {
   int8_t ignCrankFixValue = advance;
-  if ( BIT_CHECK(currentStatus.engine, BIT_ENGINE_CRANK) ) { ignCrankFixValue = configPage4.CrankAng; } //Use the fixed cranking ignition angle
+  if ( BIT_CHECK(currentStatus.engine, BIT_ENGINE_CRANK) )
+  { 
+    if ( configPage2.crkngAddCLTAdv == 0 ) { ignCrankFixValue = configPage4.CrankAng; } //Use the fixed cranking ignition angle
+    else { ignCrankFixValue = correctionCLTadvance(configPage4.CrankAng); } //Use the CLT compensated cranking ignition angle
+  }
   return ignCrankFixValue;
 }
 
diff --git a/speeduino/globals.h b/speeduino/globals.h
index b9c3e2db..0c21e4c5 100644
--- a/speeduino/globals.h
+++ b/speeduino/globals.h
@@ -781,7 +781,7 @@ struct config2 {
   byte reqFuel;       //24
   byte divider;
   byte injTiming : 1; ///< Injector timing (aka. injector staging) 0=simultaneous, 1=alternating
-  byte multiplyMAP_old : 1;
+  byte crkngAddCLTAdv : 1;
   byte includeAFR : 1; //< Enable AFR compensation ? (See also @ref config2.incorporateAFR)
   byte hardCutType : 1;
   byte ignAlgorithm : 3;
diff --git a/speeduino/updates.ino b/speeduino/updates.ino
index 7141bcdd..75b7a2d2 100644
--- a/speeduino/updates.ino
+++ b/speeduino/updates.ino
@@ -427,7 +427,7 @@ void doUpdates(void)
     configPage13.outputPin[7] = 0;
 
     //New multiply MAP option added. Set new option to be the same as old
-    configPage2.multiplyMAP = configPage2.multiplyMAP_old;
+    configPage2.multiplyMAP = configPage2.crkngAddCLTAdv;
     //New AE option added to allow for PW added in addition to existing PW multiply
     configPage2.aeApplyMode = 0; //Set the AE mode to Multiply