341 lines
14 KiB
C++
341 lines
14 KiB
C++
#ifndef DECODERS_H
|
|
#define DECODERS_H
|
|
|
|
#include "globals.h"
|
|
|
|
#if defined(CORE_AVR)
|
|
#define READ_PRI_TRIGGER() ((*triggerPri_pin_port & triggerPri_pin_mask) ? true : false)
|
|
#define READ_SEC_TRIGGER() ((*triggerSec_pin_port & triggerSec_pin_mask) ? true : false)
|
|
#define READ_THIRD_TRIGGER() ((*triggerThird_pin_port & triggerThird_pin_mask) ? true : false)
|
|
#else
|
|
#define READ_PRI_TRIGGER() digitalRead(pinTrigger)
|
|
#define READ_SEC_TRIGGER() digitalRead(pinTrigger2)
|
|
#define READ_THIRD_TRIGGER() digitalRead(pinTrigger3)
|
|
#endif
|
|
|
|
#define DECODER_MISSING_TOOTH 0
|
|
#define DECODER_BASIC_DISTRIBUTOR 1
|
|
#define DECODER_DUAL_WHEEL 2
|
|
#define DECODER_GM7X 3
|
|
#define DECODER_4G63 4
|
|
#define DECODER_24X 5
|
|
#define DECODER_JEEP2000 6
|
|
#define DECODER_AUDI135 7
|
|
#define DECODER_HONDA_D17 8
|
|
#define DECODER_MIATA_9905 9
|
|
#define DECODER_MAZDA_AU 10
|
|
#define DECODER_NON360 11
|
|
#define DECODER_NISSAN_360 12
|
|
#define DECODER_SUBARU_67 13
|
|
#define DECODER_DAIHATSU_PLUS1 14
|
|
#define DECODER_HARLEY 15
|
|
#define DECODER_36_2_2_2 16
|
|
#define DECODER_36_2_1 17
|
|
#define DECODER_420A 18
|
|
#define DECODER_WEBER 19
|
|
#define DECODER_ST170 20
|
|
#define DECODER_DRZ400 21
|
|
#define DECODER_NGC 22
|
|
#define DECODER_VMAX 23
|
|
#define DECODER_RENIX 24
|
|
#define DECODER_ROVERMEMS 25
|
|
#define DECODER_SUZUKI_K6A 26
|
|
|
|
#define BIT_DECODER_2ND_DERIV 0 //The use of the 2nd derivative calculation is limited to certain decoders. This is set to either true or false in each decoders setup routine
|
|
#define BIT_DECODER_IS_SEQUENTIAL 1 //Whether or not the decoder supports sequential operation
|
|
#define BIT_DECODER_UNUSED1 2
|
|
#define BIT_DECODER_HAS_SECONDARY 3 //Whether or not the decoder supports fixed cranking timing
|
|
#define BIT_DECODER_HAS_FIXED_CRANKING 4
|
|
#define BIT_DECODER_VALID_TRIGGER 5 //Is set true when the last trigger (Primary or secondary) was valid (ie passed filters)
|
|
#define BIT_DECODER_TOOTH_ANG_CORRECT 6 //Whether or not the triggerToothAngle variable is currently accurate. Some patterns have times when the triggerToothAngle variable cannot be accurately set.
|
|
|
|
//220 bytes free
|
|
extern volatile uint8_t decoderState;
|
|
|
|
/*
|
|
extern volatile bool validTrigger; //Is set true when the last trigger (Primary or secondary) was valid (ie passed filters)
|
|
extern volatile bool triggerToothAngleIsCorrect; //Whether or not the triggerToothAngle variable is currently accurate. Some patterns have times when the triggerToothAngle variable cannot be accurately set.
|
|
extern bool secondDerivEnabled; //The use of the 2nd derivative calculation is limited to certain decoders. This is set to either true or false in each decoders setup routine
|
|
extern bool decoderIsSequential; //Whether or not the decoder supports sequential operation
|
|
extern bool decoderHasSecondary; //Whether or not the pattern uses a secondary input
|
|
extern bool decoderHasFixedCrankingTiming;
|
|
*/
|
|
|
|
//This isn't to to filter out wrong pulses on triggers, but just to smooth out the cam angle reading for better closed loop VVT control.
|
|
#define ANGLE_FILTER(input, alpha, prior) (((long)(input) * (256 - (alpha)) + ((long)(prior) * (alpha)))) >> 8
|
|
|
|
void loggerPrimaryISR(void);
|
|
void loggerSecondaryISR(void);
|
|
void loggerTertiaryISR(void);
|
|
|
|
//All of the below are the 6 required functions for each decoder / pattern
|
|
void triggerSetup_missingTooth(void);
|
|
void triggerPri_missingTooth(void);
|
|
void triggerSec_missingTooth(void);
|
|
void triggerThird_missingTooth(void);
|
|
uint16_t getRPM_missingTooth(void);
|
|
int getCrankAngle_missingTooth(void);
|
|
extern void triggerSetEndTeeth_missingTooth(void);
|
|
|
|
|
|
void triggerSetup_DualWheel(void);
|
|
void triggerPri_DualWheel(void);
|
|
void triggerSec_DualWheel(void);
|
|
uint16_t getRPM_DualWheel(void);
|
|
int getCrankAngle_DualWheel(void);
|
|
void triggerSetEndTeeth_DualWheel(void);
|
|
|
|
void triggerSetup_BasicDistributor(void);
|
|
void triggerPri_BasicDistributor(void);
|
|
void triggerSec_BasicDistributor(void);
|
|
uint16_t getRPM_BasicDistributor(void);
|
|
int getCrankAngle_BasicDistributor(void);
|
|
void triggerSetEndTeeth_BasicDistributor(void);
|
|
|
|
void triggerSetup_GM7X(void);
|
|
void triggerPri_GM7X(void);
|
|
void triggerSec_GM7X(void);
|
|
uint16_t getRPM_GM7X(void);
|
|
int getCrankAngle_GM7X(void);
|
|
void triggerSetEndTeeth_GM7X(void);
|
|
|
|
void triggerSetup_4G63(void);
|
|
void triggerPri_4G63(void);
|
|
void triggerSec_4G63(void);
|
|
uint16_t getRPM_4G63(void);
|
|
int getCrankAngle_4G63(void);
|
|
void triggerSetEndTeeth_4G63(void);
|
|
|
|
void triggerSetup_24X(void);
|
|
void triggerPri_24X(void);
|
|
void triggerSec_24X(void);
|
|
uint16_t getRPM_24X(void);
|
|
int getCrankAngle_24X(void);
|
|
void triggerSetEndTeeth_24X(void);
|
|
|
|
void triggerSetup_Jeep2000(void);
|
|
void triggerPri_Jeep2000(void);
|
|
void triggerSec_Jeep2000(void);
|
|
uint16_t getRPM_Jeep2000(void);
|
|
int getCrankAngle_Jeep2000(void);
|
|
void triggerSetEndTeeth_Jeep2000(void);
|
|
|
|
void triggerSetup_Audi135(void);
|
|
void triggerPri_Audi135(void);
|
|
void triggerSec_Audi135(void);
|
|
uint16_t getRPM_Audi135(void);
|
|
int getCrankAngle_Audi135(void);
|
|
void triggerSetEndTeeth_Audi135(void);
|
|
|
|
void triggerSetup_HondaD17(void);
|
|
void triggerPri_HondaD17(void);
|
|
void triggerSec_HondaD17(void);
|
|
uint16_t getRPM_HondaD17(void);
|
|
int getCrankAngle_HondaD17(void);
|
|
void triggerSetEndTeeth_HondaD17(void);
|
|
|
|
void triggerSetup_Miata9905(void);
|
|
void triggerPri_Miata9905(void);
|
|
void triggerSec_Miata9905(void);
|
|
uint16_t getRPM_Miata9905(void);
|
|
int getCrankAngle_Miata9905(void);
|
|
void triggerSetEndTeeth_Miata9905(void);
|
|
int getCamAngle_Miata9905(void);
|
|
|
|
void triggerSetup_MazdaAU(void);
|
|
void triggerPri_MazdaAU(void);
|
|
void triggerSec_MazdaAU(void);
|
|
uint16_t getRPM_MazdaAU(void);
|
|
int getCrankAngle_MazdaAU(void);
|
|
void triggerSetEndTeeth_MazdaAU(void);
|
|
|
|
void triggerSetup_non360(void);
|
|
void triggerPri_non360(void);
|
|
void triggerSec_non360(void);
|
|
uint16_t getRPM_non360(void);
|
|
int getCrankAngle_non360(void);
|
|
void triggerSetEndTeeth_non360(void);
|
|
|
|
void triggerSetup_Nissan360(void);
|
|
void triggerPri_Nissan360(void);
|
|
void triggerSec_Nissan360(void);
|
|
uint16_t getRPM_Nissan360(void);
|
|
int getCrankAngle_Nissan360(void);
|
|
void triggerSetEndTeeth_Nissan360(void);
|
|
|
|
void triggerSetup_Subaru67(void);
|
|
void triggerPri_Subaru67(void);
|
|
void triggerSec_Subaru67(void);
|
|
uint16_t getRPM_Subaru67(void);
|
|
int getCrankAngle_Subaru67(void);
|
|
void triggerSetEndTeeth_Subaru67(void);
|
|
|
|
void triggerSetup_Daihatsu(void);
|
|
void triggerPri_Daihatsu(void);
|
|
void triggerSec_Daihatsu(void);
|
|
uint16_t getRPM_Daihatsu(void);
|
|
int getCrankAngle_Daihatsu(void);
|
|
void triggerSetEndTeeth_Daihatsu(void);
|
|
|
|
void triggerSetup_Harley(void);
|
|
void triggerPri_Harley(void);
|
|
void triggerSec_Harley(void);
|
|
uint16_t getRPM_Harley(void);
|
|
int getCrankAngle_Harley(void);
|
|
void triggerSetEndTeeth_Harley(void);
|
|
|
|
void triggerSetup_ThirtySixMinus222(void);
|
|
void triggerPri_ThirtySixMinus222(void);
|
|
void triggerSec_ThirtySixMinus222(void);
|
|
uint16_t getRPM_ThirtySixMinus222(void);
|
|
int getCrankAngle_ThirtySixMinus222(void);
|
|
void triggerSetEndTeeth_ThirtySixMinus222(void);
|
|
|
|
void triggerSetup_ThirtySixMinus21(void);
|
|
void triggerPri_ThirtySixMinus21(void);
|
|
void triggerSec_ThirtySixMinus21(void);
|
|
uint16_t getRPM_ThirtySixMinus21(void);
|
|
int getCrankAngle_ThirtySixMinus21(void);
|
|
void triggerSetEndTeeth_ThirtySixMinus21(void);
|
|
|
|
void triggerSetup_420a(void);
|
|
void triggerPri_420a(void);
|
|
void triggerSec_420a(void);
|
|
uint16_t getRPM_420a(void);
|
|
int getCrankAngle_420a(void);
|
|
void triggerSetEndTeeth_420a(void);
|
|
|
|
void triggerPri_Webber(void);
|
|
void triggerSec_Webber(void);
|
|
|
|
void triggerSetup_FordST170(void);
|
|
void triggerSec_FordST170(void);
|
|
uint16_t getRPM_FordST170(void);
|
|
int getCrankAngle_FordST170(void);
|
|
void triggerSetEndTeeth_FordST170(void);
|
|
|
|
void triggerSetup_DRZ400(void);
|
|
void triggerSec_DRZ400(void);
|
|
|
|
void triggerSetup_NGC(void);
|
|
void triggerPri_NGC(void);
|
|
void triggerSec_NGC4(void);
|
|
void triggerSec_NGC68(void);
|
|
uint16_t getRPM_NGC(void);
|
|
void triggerSetEndTeeth_NGC(void);
|
|
|
|
void triggerSetup_Renix(void);
|
|
void triggerPri_Renix(void);
|
|
void triggerSetEndTeeth_Renix(void);
|
|
|
|
void triggerSetup_RoverMEMS(void);
|
|
void triggerPri_RoverMEMS(void);
|
|
void triggerSec_RoverMEMS(void);
|
|
uint16_t getRPM_RoverMEMS(void);
|
|
int getCrankAngle_RoverMEMS(void);
|
|
void triggerSetEndTeeth_RoverMEMS(void);
|
|
|
|
void triggerSetup_Vmax(void);
|
|
void triggerPri_Vmax(void);
|
|
void triggerSec_Vmax(void);
|
|
uint16_t getRPM_Vmax(void);
|
|
int getCrankAngle_Vmax(void);
|
|
void triggerSetEndTeeth_Vmax(void);
|
|
|
|
void triggerSetup_SuzukiK6A(void);
|
|
void triggerPri_SuzukiK6A(void);
|
|
void triggerSec_SuzukiK6A(void);
|
|
uint16_t getRPM_SuzukiK6A(void);
|
|
int getCrankAngle_SuzukiK6A(void);
|
|
void triggerSetEndTeeth_SuzukiK6A(void);
|
|
|
|
|
|
|
|
extern void (*triggerHandler)(void); //Pointer for the trigger function (Gets pointed to the relevant decoder)
|
|
extern void (*triggerSecondaryHandler)(void); //Pointer for the secondary trigger function (Gets pointed to the relevant decoder)
|
|
extern void (*triggerTertiaryHandler)(void); //Pointer for the tertiary trigger function (Gets pointed to the relevant decoder)
|
|
|
|
extern uint16_t (*getRPM)(void); //Pointer to the getRPM function (Gets pointed to the relevant decoder)
|
|
extern int (*getCrankAngle)(void); //Pointer to the getCrank Angle function (Gets pointed to the relevant decoder)
|
|
extern void (*triggerSetEndTeeth)(void); //Pointer to the triggerSetEndTeeth function of each decoder
|
|
|
|
extern volatile unsigned long curTime;
|
|
extern volatile unsigned long curGap;
|
|
extern volatile unsigned long curTime2;
|
|
extern volatile unsigned long curGap2;
|
|
extern volatile unsigned long lastGap;
|
|
extern volatile unsigned long targetGap;
|
|
|
|
extern unsigned long MAX_STALL_TIME; //The maximum time (in uS) that the system will continue to function before the engine is considered stalled/stopped. This is unique to each decoder, depending on the number of teeth etc. 500000 (half a second) is used as the default value, most decoders will be much less.
|
|
extern volatile uint16_t toothCurrentCount; //The current number of teeth (Once sync has been achieved, this can never actually be 0
|
|
extern volatile byte toothSystemCount; //Used for decoders such as Audi 135 where not every tooth is used for calculating crank angle. This variable stores the actual number of teeth, not the number being used to calculate crank angle
|
|
extern volatile unsigned long toothSystemLastToothTime; //As below, but used for decoders where not every tooth count is used for calculation
|
|
extern volatile unsigned long toothLastToothTime; //The time (micros()) that the last tooth was registered
|
|
extern volatile unsigned long toothLastSecToothTime; //The time (micros()) that the last tooth was registered on the secondary input
|
|
extern volatile unsigned long toothLastThirdToothTime; //The time (micros()) that the last tooth was registered on the second cam input
|
|
extern volatile unsigned long toothLastMinusOneToothTime; //The time (micros()) that the tooth before the last tooth was registered
|
|
extern volatile unsigned long toothLastMinusOneSecToothTime; //The time (micros()) that the tooth before the last tooth was registered on secondary input
|
|
extern volatile unsigned long targetGap2;
|
|
|
|
extern volatile unsigned long toothOneTime; //The time (micros()) that tooth 1 last triggered
|
|
extern volatile unsigned long toothOneMinusOneTime; //The 2nd to last time (micros()) that tooth 1 last triggered
|
|
extern volatile bool revolutionOne; // For sequential operation, this tracks whether the current revolution is 1 or 2 (not 1)
|
|
|
|
extern volatile unsigned int secondaryToothCount; //Used for identifying the current secondary (Usually cam) tooth for patterns with multiple secondary teeth
|
|
extern volatile unsigned long secondaryLastToothTime; //The time (micros()) that the last tooth was registered (Cam input)
|
|
extern volatile unsigned long secondaryLastToothTime1; //The time (micros()) that the last tooth was registered (Cam input)
|
|
|
|
extern uint16_t triggerActualTeeth;
|
|
extern volatile unsigned long triggerFilterTime; // The shortest time (in uS) that pulses will be accepted (Used for debounce filtering)
|
|
extern volatile unsigned long triggerSecFilterTime; // The shortest time (in uS) that pulses will be accepted (Used for debounce filtering) for the secondary input
|
|
extern unsigned int triggerSecFilterTime_duration; // The shortest valid time (in uS) pulse DURATION
|
|
extern volatile uint16_t triggerToothAngle; //The number of crank degrees that elapse per tooth
|
|
extern byte checkSyncToothCount; //How many teeth must've been seen on this revolution before we try to confirm sync (Useful for missing tooth type decoders)
|
|
extern unsigned long elapsedTime;
|
|
extern unsigned long lastCrankAngleCalc;
|
|
extern unsigned long lastVVTtime; //The time between the vvt reference pulse and the last crank pulse
|
|
|
|
typedef uint32_t UQ24X8_t;
|
|
constexpr uint8_t UQ24X8_Shift = 8U;
|
|
|
|
/** @brief uS per degree at current RPM in UQ24.8 fixed point */
|
|
extern UQ24X8_t microsPerDegree;
|
|
constexpr uint8_t microsPerDegree_Shift = UQ24X8_Shift;
|
|
|
|
typedef uint16_t UQ1X15_t;
|
|
constexpr uint8_t UQ1X15_Shift = 15U;
|
|
|
|
/** @brief Degrees per uS in UQ1.15 fixed point.
|
|
*
|
|
* Ranges from 8 (0.000246) at MIN_RPM to 3542 (0.108) at MAX_RPM
|
|
*/
|
|
extern UQ1X15_t degreesPerMicro;
|
|
constexpr uint8_t degreesPerMicro_Shift = UQ1X15_Shift;
|
|
|
|
extern uint16_t ignition1EndTooth;
|
|
extern uint16_t ignition2EndTooth;
|
|
extern uint16_t ignition3EndTooth;
|
|
extern uint16_t ignition4EndTooth;
|
|
extern uint16_t ignition5EndTooth;
|
|
extern uint16_t ignition6EndTooth;
|
|
extern uint16_t ignition7EndTooth;
|
|
extern uint16_t ignition8EndTooth;
|
|
|
|
extern int16_t toothAngles[24]; //An array for storing fixed tooth angles. Currently sized at 24 for the GM 24X decoder, but may grow later if there are other decoders that use this style
|
|
|
|
#define CRANK_SPEED 0U
|
|
#define CAM_SPEED 1U
|
|
|
|
#define TOOTH_CRANK 0
|
|
#define TOOTH_CAM_SECONDARY 1
|
|
#define TOOTH_CAM_TERTIARY 2
|
|
|
|
// used by the ROVER MEMS pattern
|
|
#define ID_TOOTH_PATTERN 0 // have we identified teeth to skip for calculating RPM?
|
|
#define SKIP_TOOTH1 1
|
|
#define SKIP_TOOTH2 2
|
|
#define SKIP_TOOTH3 3
|
|
#define SKIP_TOOTH4 4
|
|
|
|
#endif
|