speeduino/test/test_decoders/renix/renix.cpp

#include <decoders.h>
#include <globals.h>
#include <unity.h>
#include "renix.h"
#include "schedule_calcs.h"
#include "../../test_utils.h"

void test_setup_renix44()
{
    //Setup a renix 44 tooth wheel
    configPage4.TrigPattern = DECODER_RENIX;
    configPage2.nCylinders = 4;

    triggerSetup_Renix();
}

void test_setup_renix66()
{
    //Setup a renix 66 tooth wheel
    configPage4.TrigPattern = DECODER_RENIX;
    configPage2.nCylinders = 6;

    triggerSetup_Renix();
}

//************************************** Begin the new ignition setEndTooth tests **************************************
void test_Renix_newIgn_44_trig0_1()
{
    //Test the set end tooth function. Conditions:
    //Advance: 10
    //triggerAngle=0
    test_setup_renix44();
    configPage4.sparkMode = IGN_MODE_SINGLE;
    ignition1EndAngle = 360 - 10; //Set 10 degrees advance
    configPage4.triggerAngle = 0; //No trigger offset
    
    triggerSetEndTeeth_Renix();
    TEST_ASSERT_EQUAL(2, ignition1EndTooth);
}

void test_Renix_newIgn_44_trig90_1()
{
    //Test the set end tooth function. Conditions:

    //Advance: 10
    //triggerAngle=90
    test_setup_renix44();
    configPage4.sparkMode = IGN_MODE_SINGLE;
    ignition1EndAngle = 360 - 10; //Set 10 degrees advance
    configPage4.triggerAngle = 90; //No trigger offset
    
    triggerSetEndTeeth_Renix();
    TEST_ASSERT_EQUAL(1, ignition1EndTooth);
}

void test_Renix_newIgn_44_trig180_1()
{
    //Test the set end tooth function. Conditions:
    //Advance: 10
    //triggerAngle=180
    test_setup_renix44();
    configPage4.sparkMode = IGN_MODE_SINGLE;
    ignition1EndAngle = 360 - 10; //Set 10 degrees advance
    configPage4.triggerAngle = 180; //No trigger offset
    
    triggerSetEndTeeth_Renix();
    TEST_ASSERT_EQUAL(4, ignition1EndTooth);
}

void test_Renix_newIgn_44_trig270_1()
{
    //Test the set end tooth function. Conditions:
    //Advance: 10
    //triggerAngle=270
    test_setup_renix44();
    configPage4.sparkMode = IGN_MODE_SINGLE;
    ignition1EndAngle = 360 - 10; //Set 10 degrees advance
    configPage4.triggerAngle = 270; //No trigger offset
    
    triggerSetEndTeeth_Renix();
    TEST_ASSERT_EQUAL(3, ignition1EndTooth);
}

void test_Renix_newIgn_44_trig360_1()
{
    //Test the set end tooth function. Conditions:
    //Advance: 10
    //triggerAngle=360
    test_setup_renix44();
    configPage4.sparkMode = IGN_MODE_SINGLE;
    ignition1EndAngle = 360 - 10; //Set 10 degrees advance
    configPage4.triggerAngle = 360; //No trigger offset
    
    triggerSetEndTeeth_Renix();
    TEST_ASSERT_EQUAL(3, ignition1EndTooth);
}

void test_Renix_newIgn_44_trigNeg90_1()
{
    //Test the set end tooth function. Conditions:
    //Advance: 10
    //triggerAngle=-90
    test_setup_renix44();
    configPage4.sparkMode = IGN_MODE_SINGLE;
    ignition1EndAngle = 360 - 10; //Set 10 degrees advance
    configPage4.triggerAngle = -90; //No trigger offset
    
    triggerSetEndTeeth_Renix();
    TEST_ASSERT_EQUAL(3, ignition1EndTooth);
}

void test_Renix_newIgn_44_trigNeg180_1()
{
    //Test the set end tooth function. Conditions:
    //Advance: 10
    //triggerAngle=-180
    test_setup_renix44();
    configPage4.sparkMode = IGN_MODE_SINGLE;
    ignition1EndAngle = 360 - 10; //Set 10 degrees advance
    configPage4.triggerAngle = -180; //No trigger offset
    
    triggerSetEndTeeth_Renix();
    TEST_ASSERT_EQUAL(4, ignition1EndTooth);
}

void test_Renix_newIgn_44_trigNeg270_1()
{
    //Test the set end tooth function. Conditions:
    //Advance: 10
    //triggerAngle=-270
    test_setup_renix44();
    configPage4.sparkMode = IGN_MODE_SINGLE;
    ignition1EndAngle = 360 - 10; //Set 10 degrees advance
    configPage4.triggerAngle = -270; //No trigger offset
    
    triggerSetEndTeeth_Renix();
    TEST_ASSERT_EQUAL(1, ignition1EndTooth);
}

void test_Renix_newIgn_44_trigNeg360_1()
{
    //Test the set end tooth function. Conditions:
    //Advance: 10
    //triggerAngle=-360
    test_setup_renix44();
    configPage4.sparkMode = IGN_MODE_SINGLE;
    ignition1EndAngle = 360 - 10; //Set 10 degrees advance
    configPage4.triggerAngle = -360; //No trigger offset
    
    triggerSetEndTeeth_Renix();
    TEST_ASSERT_EQUAL(2, ignition1EndTooth);
}

// ******* CHannel 2 *******
void test_Renix_newIgn_44_trig0_2()
{
    //Test the set end tooth function. Conditions:
    //Advance: 10
    //triggerAngle=0
    test_setup_renix44();
    configPage4.sparkMode = IGN_MODE_SINGLE;
    ignition2EndAngle = 180 - 10; //Set 10 degrees advance
    configPage4.triggerAngle = 0; //No trigger offset
    
    triggerSetEndTeeth_Renix();
    TEST_ASSERT_EQUAL(4, ignition2EndTooth);
}

void test_Renix_newIgn_44_trig90_2()
{
    //Test the set end tooth function. Conditions:
    //Advance: 10
    //triggerAngle=90
    test_setup_renix44();
    configPage4.sparkMode = IGN_MODE_SINGLE;
    ignition2EndAngle = 180 - 10; //Set 10 degrees advance
    configPage4.triggerAngle = 90; //No trigger offset
    
    triggerSetEndTeeth_Renix();
    TEST_ASSERT_EQUAL(3, ignition2EndTooth);
}

void test_Renix_newIgn_44_trig180_2()
{
    //Test the set end tooth function. Conditions:
    //Advance: 10
    //triggerAngle=180
    test_setup_renix44();
    configPage4.sparkMode = IGN_MODE_SINGLE;
    ignition2EndAngle = 180 - 10; //Set 10 degrees advance
    configPage4.triggerAngle = 180; //No trigger offset
    
    triggerSetEndTeeth_Renix();
    TEST_ASSERT_EQUAL(3, ignition2EndTooth);
}

void test_Renix_newIgn_44_trig270_2()
{
    //Test the set end tooth function. Conditions:
    //Advance: 10
    //triggerAngle=270
    test_setup_renix44();
    configPage4.sparkMode = IGN_MODE_SINGLE;
    ignition2EndAngle = 180 - 10; //Set 10 degrees advance
    configPage4.triggerAngle = 270; //No trigger offset
    
    triggerSetEndTeeth_Renix();
    TEST_ASSERT_EQUAL(2, ignition2EndTooth);
}

void test_Renix_newIgn_44_trig366()
{
    //Test the set end tooth function. Conditions:
    //Advance: 10
    //triggerAngle=360
    test_setup_renix44();
    configPage4.sparkMode = IGN_MODE_SINGLE;
    ignition2EndAngle = 180 - 10; //Set 10 degrees advance
    configPage4.triggerAngle = 360; //No trigger offset
    
    triggerSetEndTeeth_Renix();
    TEST_ASSERT_EQUAL(1, ignition2EndTooth);
}

void test_Renix_newIgn_44_trigNeg90_2()
{
    //Test the set end tooth function. Conditions:
    //Advance: 10
    //triggerAngle=-90
    test_setup_renix44();
    configPage4.sparkMode = IGN_MODE_SINGLE;
    ignition2EndAngle = 180 - 10; //Set 10 degrees advance
    configPage4.triggerAngle = -90; //No trigger offset
    
    triggerSetEndTeeth_Renix();
    TEST_ASSERT_EQUAL(1, ignition2EndTooth);
}

void test_Renix_newIgn_44_trigNeg180_2()
{
    //Test the set end tooth function. Conditions:
    //Advance: 10
    //triggerAngle=-180
    test_setup_renix44();
    configPage4.sparkMode = IGN_MODE_SINGLE;
    ignition2EndAngle = 180 - 10; //Set 10 degrees advance
    configPage4.triggerAngle = -180; //No trigger offset
    
    triggerSetEndTeeth_Renix();
    TEST_ASSERT_EQUAL(2, ignition2EndTooth);
}

void test_Renix_newIgn_44_trigNeg270_2()
{
    //Test the set end tooth function. Conditions:
     //Advance: 10
    //triggerAngle=-270
    test_setup_renix44();
    configPage4.sparkMode = IGN_MODE_SINGLE;
    ignition2EndAngle = 180 - 10; //Set 10 degrees advance
    configPage4.triggerAngle = -270; //No trigger offset
    
    triggerSetEndTeeth_Renix();
    TEST_ASSERT_EQUAL(3, ignition2EndTooth);
}

void test_Renix_newIgn_44_trigNeg366()
{
    //Test the set end tooth function. Conditions:
    //Advance: 10
    //triggerAngle=-360
    test_setup_renix44();
    configPage4.sparkMode = IGN_MODE_SINGLE;
    ignition2EndAngle = 180 - 10; //Set 10 degrees advance
    configPage4.triggerAngle = -360; //No trigger offset
    
    triggerSetEndTeeth_Renix();
    TEST_ASSERT_EQUAL(4, ignition2EndTooth);
}

void test_Renix_newIgn_66_trig0_2()
{
    //Test the set end tooth function. Conditions:

    //Advance: 10
    //triggerAngle=300
    test_setup_renix66();
    configPage4.sparkMode = IGN_MODE_SINGLE;
    ignition2EndAngle = 180 - 10; //Set 10 degrees advance
    configPage4.triggerAngle = 0; //No trigger offset
    
    triggerSetEndTeeth_Renix();
    TEST_ASSERT_EQUAL(1, ignition2EndTooth);
}

void test_Renix_newIgn_66_trig181_2()
{
    //Test the set end tooth function. Conditions:

    //Advance: 10
    //triggerAngle=300
    test_setup_renix66();
    configPage4.sparkMode = IGN_MODE_SINGLE;
    ignition2EndAngle = 180 - 10; //Set 10 degrees advance
    configPage4.triggerAngle = 181; //No trigger offset
    
    triggerSetEndTeeth_Renix();
    TEST_ASSERT_EQUAL(5, ignition2EndTooth);
}


void testRenix()
{
  SET_UNITY_FILENAME() {

  RUN_TEST(test_Renix_newIgn_44_trig0_1);
  RUN_TEST(test_Renix_newIgn_44_trig90_1);
  RUN_TEST(test_Renix_newIgn_44_trig180_1);
  RUN_TEST(test_Renix_newIgn_44_trig270_1);
  RUN_TEST(test_Renix_newIgn_44_trig360_1);
  RUN_TEST(test_Renix_newIgn_44_trigNeg90_1);
  RUN_TEST(test_Renix_newIgn_44_trigNeg180_1);
  RUN_TEST(test_Renix_newIgn_44_trigNeg270_1);
  RUN_TEST(test_Renix_newIgn_44_trigNeg360_1);

  RUN_TEST(test_Renix_newIgn_44_trig0_2);
  RUN_TEST(test_Renix_newIgn_44_trig90_2);
  RUN_TEST(test_Renix_newIgn_44_trig180_2);
  RUN_TEST(test_Renix_newIgn_44_trig270_2);
  RUN_TEST(test_Renix_newIgn_44_trig366);
  RUN_TEST(test_Renix_newIgn_44_trigNeg90_2);
  RUN_TEST(test_Renix_newIgn_44_trigNeg180_2);
  RUN_TEST(test_Renix_newIgn_44_trigNeg270_2);
  RUN_TEST(test_Renix_newIgn_44_trigNeg366);

  RUN_TEST(test_Renix_newIgn_66_trig0_2);
  RUN_TEST(test_Renix_newIgn_66_trig181_2);
  }           
}