rusefi/firmware/tunerstudio/rusefi.input

; this is TunerStudio project for www.rusefi.com DIY engine management system
;
; rusefi.ini is generated by invoking gen_config.bat (look inside for the exact command to run it outside of Windows)
; inputs are rusefi.input template and rusefi_config.txt file
;

; this should stop TS from looking for the CAN ID in the 2nd byte location and allow the page reads to work correctly.
enable2ndByteCanID = false

#unset tuneByMAF

;[SettingGroups]
   ; the referenceName will over-ride previous, so if you are creating a 
   ; settingGroup with a reference name of lambdaSensor, it will replace the 
   ; setting group defined in the settingGroups.xml of the TunerStudio config
   ; folder. If is is an undefined referenceName, it will be added.
   ; keyword    =  referenceName,  DisplayName

;    settingGroup = fAlgorithmSetting, "Fuel Logic / Tables"  
;    settingOption = FA_PLAIN_MAF, "Plain MAF"
;    settingOption = FA_TPS, "AlphaN/TPS"
;    settingOption = DEFAULT, "Speed Density" ; DEFAULT will be over looked and this will fall into the #else block of the statement.



[TunerStudio]
   queryCommand   = "S"
   versionInfo    = "V"  ; firmwave version for title bar.
   signature    = "MShift v0.02" ; signature is expected to be 7 or more characters.

[Constants]
; new packet serial format with CRC
   messageEnvelopeFormat = msEnvelope_1.0

   endianness          = little
   nPages              = 1
  

   pageIdentifier      = "\x00\x00"
   pageReadCommand     = "R\x00\x00%2o%2c"
   burnCommand         = "B\x00\x00"
   pageActivate        = "P\x00\x00"
   pageValueWrite      = "W\x00\x00%2o%v"
   pageChunkWrite      = "C\x00\x00%2o%2c%v"
;   crc32CheckCommand   = "k%2i%2o\xB8\x36"
   crc32CheckCommand   = "k\x00\x00\x00\x00\x36\xB8"

;communication settings
   pageActivationDelay = 500 ; Milliseconds delay after burn command. See https://sourceforge.net/p/rusefi/tickets/77/
;e.g. put writeblocks off and add an interwrite delay
   writeBlocks = on
   interWriteDelay = 10
   blockReadTimeout    = 3000; Milliseconds general timeout
   
 ; delayAfterPortOpen = 500  
   
   blockingFactor = 400 ; max chunk size
;end communication settings

   ;  name      			= bits,   type, offset,  bits
   ;  name           		= array,  type, offset,  shape, units,     scale, translate,    lo,      hi, digits
   ;  name       			= scalar, type, offset,         units,     scale, translate,    lo,      hi, digits

; see PAGE_0_SIZE in C source code    
; CONFIG_DEFINITION_START

; this section will be generated automatically by ConfigDefinition.jar based on rusefi_config.txt

; CONFIG_DEFINITION_END
	

[SettingContextHelp]

	fuelAlgorithm = "See also http://rusefi.com/fuel"

[Tuning]
   spotDepth       =   2 ; 0 = no indicators, 1 = Z only, 2 = XYZ indicators.
   cursorDepth     =   2 ; Same as spot depth.

   gaugeColumns = 1 ; Only 1 or 2 are valid.

   pageButtons  = "&EGO"
   gauge1       = RPMGauge	
   gauge2       = afr1Gauge
   gauge3		= MAPGauge
   gauge4		= veValueGauge


[LoggerDefinition]

  ; valid logger types: composite, tooth, trigger, csv
  loggerDef = tooth, "Tooth Logger", tooth
         dataReadCommand = "L"
         dataReadTimeout = 15000 ; time in ms
         dataReadyCondition = { toothLogReady }
         dataLength = 256 ; in bytes, including headers, footers and data

       ; recordDef = headerLen, footerLen, recordLen
       recordDef =   0,   0,   4; in bytes, the recordLen is for each record, currently limited to 4 bytes


       recordField = PA3,               "Inj D",         3,  1, 1,   ""
       recordField = PA2,               "Inj C",         2,  1, 1,   ""
       recordField = PA1,               "Inj B",         1,  1, 1,   ""
       recordField = PA0,               "Inj A",         0,  1, 1,   ""

[VeAnalyze]

        ;    tableName,  lambdaTargetTableName, lambdaChannel, egoCorrectionChannel, activeCondition
#if tuneByMAF
       veAnalyzeMap = fuelTableTbl, afrTableTbl, AFRValue, egoCorrection, { 1 }
#else
       veAnalyzeMap = veTableTbl, afrTableTbl, AFRValue, egoCorrection, { 1 }
#endif
 ;lambdaTargetTables = afrTable1Tbl, afrTable2Tbl, afrTSCustom

       ; filter =  Name,        "DisplayName", outputChannel, operator, defaultVal, userAdjustable
        filter = minRPMFilter, "Minimum RPM", RPMValue,           <       , 500,      , true

#if CELSIUS          
         filter = minCltFilter, "Minimum CLT", coolant,       <       , 60,       , true
#else
         filter = minCltFilter, "Minimum CLT", coolant,       <       , 160,      , true
#endif

         filter = deltaTps, "dTPS", deltaTps       >       , 50,      , true

		filter = VBatt, "VBatt", VBatt       <       , 12,      , true

;         filter = minTps, "Minimum TPS", TPS,       >       , 1,       , true


;[VeAnalyze]
;       fuelAnalyzeMap = fuelTableTbl, afrTableTbl, AFRValue, egoCorrection , { 1 }
;        filter = minRPMFilter, "Minimum RPM", RPMValue,           <       , 500,      , true



[OutputChannels]

; see TS_FILE_VERSION in firmware code
fileVersion = { 20171101 }

   ochGetCommand    = "O%2o%2c"

; see TS_OUTPUT_SIZE in console source code
   ochBlockSize     = 356

      RPMValue        = scalar,  U32,      0,             "RPM",            1,   0.00000
#if CELSIUS
      coolant         = scalar,  F32,      4,              "<22>C",            1,       0.0
#else
      coolant         = scalar,  F32,      4,              "<22>F",         {9/5},  17.77777
#endif
#if CELSIUS
      intake          = scalar,  F32,      8,              "<22>C",            1,       0.0
#else
      intake          = scalar,  F32,      8,              "<22>F",         {9/5},  17.77777
#endif
      TPSValue        = scalar,  F32,     12,               "%",            1,         0
      MAFValue        = scalar,  F32,     16,               "V",            1,         0
      AFRValue       = scalar,  F32,     20,             "AFR",            1,       0.0
      engineLoad      = scalar,	 F32,     24,	    "%",            1,       0.0 ; Blend of MAP and TPS, depends on algorithm
      VBatt	          = scalar,	 F32,     28,	            "V",            1,       0.0
      ; 10 bit TPS ADC value (from 0 to 1023 in 5v scale)
      tpsADC          = scalar,  U16,     32,             "ADC",            1,       0.0;
      alignmet        = scalar,  U16,     34,              "al",            1,       0.0;
      baroPressure    = scalar,  F32,     36,             "pres",           1,       0.0;
      MAPValue        = scalar,  F32,     40,              "MAP",           1,       0.0;
	  ; total fuel squirt duration (in MS) per engine cycle according to current CLT
	  crankingFuel    = scalar,  F32,     44,              "ms",            1,       0.0;
      baseFuel        = scalar,  F32,     48,              "ms",           1,         0
      tCharge         = scalar,  F32,     52,              "T",             1,       0.0;
      ignitionAdvance = scalar,  F32,     56,              "deg",           1,       0.0;
      sparkDwellValue = scalar,  F32,     60,              "ms",           1,       0.0;
      ; actual total Ms time per engine cycle with all corrections
      actualLastInjection      = scalar,  F32,     64,              "ms",           1,       0.0;
      debugFloatField1    = scalar,  F32,  68,            "val",           1,       0.0;
      
      hasSdCard       = bits,    U32,     72, [0:0], "true", "false";
	  isIgnitionEnabledIndicator=bits, U32,     72, [1:1], "true", "false";
	  ind_injection_enabled=bits,U32,     72, [2:2], "true", "false";
	  isCylinderCleanupEnabled=bits, U32, 72, [3:3], "true", "false";
	  isCylinderCleanupActivated=bits,U32,72, [4:4], "true", "false";
	  ind_fuel_pump   = bits,    U32,     72, [5:5], "true", "false";
	  ind_fan         = bits,    U32,     72, [6:6], "true", "false";
	  ind_o2_heater   = bits,    U32,     72, [7:7], "true", "false";
      ind_check_engine= bits,    U32,     72, [8:8], "true", "false";
      needBurn        = bits,    U32,     72, [9:9], "true", "false";
      ind_2nd_trigger_en=bits,   U32,     72, [10:10], "true", "false";
      clutchUpState    =bits,    U32,     72, [11:11], "true", "false";
      clutchDownState  =bits,    U32,     72, [12:12], "true", "false";
      knockEverIndicator=bits,   U32,     72, [13:13], "true", "false";
      knockNowIndicator=bits,    U32,     72, [14:14], "true", "false";
      brakePedalIndicator=bits,  U32,     72, [15:15], "true", "false";
      toothLogReady      =bits,  U32,     72, [16:16], "true", "false";
      vehicleSpeedKph = scalar,  F32,     76,        "kph",   1,       0.0;
      
      ind_tps_error   = bits,    U32,     80, [0:0], "true", "false";
      ind_clt_error   = bits,    U32,     80, [1:1], "true", "false";
      ind_map_error   = bits,    U32,     80, [2:2], "true", "false";
      ind_iat_error   = bits,    U32,     80, [3:3], "true", "false";
      ind_isTriggerError = bits, U32,     80, [5:5], "true", "false";
      ind_hasFatalError=bits,    U32,     80, [6:6], "true", "false";
      ind_isWarnNow    =bits,    U32,     80, [7:7], "true", "false";
      firmwareTsVersion = scalar,U32,     84, "version_p",           1,         0
      egt1            = scalar,  S16,     88, "<22>C",           1,         0
      egt2            = scalar,  S16,     90, "<22>C",           1,         0
      egt3            = scalar,  S16,     92, "<22>C",           1,         0
      egt4            = scalar,  S16,     94, "<22>C",           1,         0
      egt5            = scalar,  S16,     96, "<22>C",           1,         0
      egt6            = scalar,  S16,     98, "<22>C",           1,         0
      egt7            = scalar,  S16,    100, "<22>C",           1,         0
      egt8            = scalar,  S16,    102, "<22>C",           1,         0
      rpmAcceleration = scalar,  F32,    104, "dRpm",         1,         0
      massAirFlowValue= scalar,  F32,    108, "Kg/h",         1,         0
      veValue         = scalar,  F32,    112, "ratio",        1,         0
      deltaTps        = scalar,  F32,    116, "ratio",        1,         0
      triggerErrorsCounter = scalar, U32,120, "counter",      1,         0
      engineLoadAccelExtra = scalar,F32, 124, "value",        1,         0
      tpsAccelFuel    = scalar,  F32,    128, "ms",           1,         0
      baroCorrection  = scalar,  F32,    132, "%",            1,         0
      pedalPosition   = scalar,  F32,    136, "%",            1,         0
      injectorDutyCycle= scalar, F32,    140, "%",            1,         0
      knockCount      = scalar,  U32,    144, "counter",      1,         0
      ; fuelLevel 148
      knockLevel      = scalar,  F32,    152, "Volts",        1,         0
      ; totalTriggerErrorCounter 156
      wallFuelAmount = scalar, F32,      160, "ms",           1,         0
      iatCorrection = scalar, F32,       164, "%",            1,         0
      wallFuelCorrection = scalar, F32,  168, "ms",           1,         0
      idleAirValvePosition = scalar, F32,     172, "percent",      1,         0
      currentTargetAfr = scalar, F32,    176, "ratio",      1,         0
      chargeAirMass = scalar, F32,       180, "g",      1,         0
      cltCorrection = scalar, F32,       184, "%",            1,         0
      fuelRunning = scalar, F32,         188, "g",      1,         0
      debugIntField1    = scalar,  U32,  192, "val",          1,       0.0;
      debugFloatField2  = scalar,  F32,  200,            "val",           1,       0.0;
      debugFloatField3  = scalar,  F32,  204,            "val",           1,       0.0;
      debugFloatField4  = scalar,  F32,  208,            "val",           1,       0.0;
      debugFloatField5  = scalar,  F32,  212,            "val",           1,       0.0;
      debugIntField2    = scalar,  U32,   216, "val",          1,       0.0;
      debugIntField3    = scalar,  U32,   220, "val",          1,       0.0;
      engineLoadDelta = scalar,F32, 228, "value",            1,         0
      speedToRpmRatio = scalar,F32, 232, "value",            1,         0
      warningCounter = scalar,U32, 236, "count",            1,         0
      lastErrorCode = scalar,U32, 240, "error",            1,         0
      internalMcuTemperature = scalar,F32, 244, "C",            1,         0
      vvtPosition = scalar,F32, 248, "deg",            1,         0
      engineMode    = scalar,  U32,   252, "em",          1,       0.0;
      debugFloatField6  = scalar,  F32,  256,            "val",           1,       0.0;
      debugFloatField7  = scalar,  F32,  260,            "val",           1,       0.0;
      firmwareVersion = scalar,U32,     264, "version_f",           1,         0
      fuelPidCorrection        = scalar,  F32,     268,              "ms",           1,         0
      coilDutyCycle        = scalar,  F32,     272,              "perc",           1,         0
      accelerationX        = scalar,  S16,     276,              "G",           0.01,         0
      accelerationY        = scalar,  S16,     276,              "G",           0.01,         0
	  oilPressure		   = scalar,  F32,     280,				 "kPa",			1, 0.0

; todo: generate this section programatically
	LM_PLAIN_MAF = {0},
	LM_ALPHA_N = {1},
	LM_MAP = {2},
	LM_SPEED_DENSITY = {3},
	LM_REAL_MAF = {4}

      egoCorrection   = { 100 }
      time            = { timeNow }
;      engineLoad      = { fuleAlgorithm == 0 ? MAF : TPS }

[PcVariables]
    wueAfrTargetOffset = array, S16, [ 16], ":1",   0.1, 0.0, -3.0, 3.0, 1;
    wueAnalRecommend   = array, U08, [ 16], "%",  1.00, 0.0, 100, 255.00, 0

[ConstantsExtensions]
    defaultValue = wueAfrTargetOffset, -1.5 -1.4 -1.15 -0.95 -0.775 -0.65 -0.5625 -0.5 -0.4375 -0.375 -0.3125 -0.25 -0.1875 -0.125 -0.0625 0

[CurveEditor]
;	xAxis       =  leftValue, rightValue, step
;	yAxis       =  bottomValue, topValue, step


	curve = knockThresholdCurve, "Engine knock threshold RPM based"
      columnLabel = "RPM", "Threshold"
      xAxis       =  0, 8000, 10
      yAxis       =  0,  8, 10
      xBins       = knockNoiseRpmBins, RPMValue
      yBins       = knockNoise
      gauge       = RPMValue

	curve = narrowToWideOxygenCurve, "Narrow to Wideband approximation"
      columnLabel = "Voltage", "AFR"
      xAxis       =  0, 6, 10
      yAxis       =  0,  28, 10
      xBins       = narrowToWideOxygenBins
      yBins       = narrowToWideOxygen
      gauge       = afr1Gauge

   curve = fsioCurve1, "FSIO Curve #1"
      columnLabel = "X", "Y"
      xAxis       =  0, 128, 10
      yAxis       = -155,  150, 10
      xBins       = fsioCurve1Bins
      yBins       = fsioCurve1
      
   curve = fsioCurve2, "FSIO Curve #2"
      columnLabel = "X", "Y"
      xAxis       =  0, 128, 10
      yAxis       = -150,  150, 10
      xBins       = fsioCurve2Bins
      yBins       = fsioCurve2

   curve = fsioCurve3, "FSIO Curve #3"
      columnLabel = "X", "Y"
      xAxis       =  0, 128, 10
      yAxis       = -5,  5, 10
      xBins       = fsioCurve3Bins
      yBins       = fsioCurve3

   curve = fsioCurve4, "FSIO Curve #4"
      columnLabel = "X", "Y"
      xAxis       =  0, 128, 10
      yAxis       = -5,  5, 10
      xBins       = fsioCurve4Bins
      yBins       = fsioCurve4

   curve = mapAccelTaper, "Engine Load Acceleration Enrichment Taper"
      columnLabel = "Distance", "Multiplier"
      xAxis       =  0, 128, 10
      yAxis       = -5,  5, 10
      xBins       = mapAccelTaperBins
      yBins       = mapAccelTaperMult

	curve = dwellCorrection, "Dwell time RPM based"
      columnLabel = "RPM", "Dwell"
      xAxis       =  0, 8000, 10
      yAxis       =  0,  30, 10
      xBins       = sparkDwellRpmBins, RPMValue
      yBins       = sparkDwellValues
      gauge       = RPMValue
    
   curve = map_samplingAngleCurve, "MAP Sampling Start Angle"
      columnLabel = "RPM", "Angle"
      xAxis       =  0, 8000, 10
      yAxis       =  0,  180, 10
      xBins       = map_samplingAngleBins, RPMValue
      yBins       = map_samplingAngle
      gauge       = RPMValue
   
   curve = map_samplingWindowCurve, "MAP Sampling Duration"
      columnLabel = "RPM", "Window"
      xAxis       =  0, 8000, 10
      yAxis       =  0,  180, 10
      xBins       = map_samplingWindowBins, RPMValue
      yBins       = map_samplingWindow
      gauge       = RPMValue

   curve = injectorsDeadTime, "Injector Dead Time by VBatt"
      columnLabel = "Voltage", "Dead Time"
      xAxis       =  8, 21, 10
      yAxis       = -3,  3, 10
      xBins       = injector_battLagCorrBins, VBatt
      yBins       = injector_battLagCorr
      gauge       = VBattGauge
      
   curve = mafDecodingCurve, "MAF Sensor Settings"
      columnLabel = "Voltage", "kg/hour"
      xAxis       =  -1, 6, 10
      yAxis       = -30,  1300, 10
      xBins       = mafDecodingBins, MAFValue
      yBins       = mafDecoding
      gauge       = MAFGauge

   curve = iatFuelCorrCurve, "Intake air temperature fuel Multiplier"
      columnLabel = "Coolant", "Multiplier"
      xAxis       =  -40, 120, 10
      yAxis       =  0,  5, 10
      xBins       = iatFuelCorrBins, intake
      yBins       = iatFuelCorr
      gauge       = IATGauge
	
	curve = cltTimingCorrCurve, "Warmup timing correction"
      columnLabel = "Coolant", "Extra"
      xAxis       =  -40, 120, 10
      yAxis       =  0,  50, 100
      xBins       = cltTimingBins, coolant
      yBins       = cltTimingExtra
      gauge       = CLTGauge

	curve = cltFuelCorrCurve, "Warmup fuel manual Multiplier"
      columnLabel = "Coolant", "Multiplier"
      xAxis       =  -40, 120, 10
      yAxis       =  0,  50, 100
      xBins       = cltFuelCorrBins, coolant
      yBins       = cltFuelCorr
      gauge       = CLTGauge

	curve = crankingCltCurve, "Cranking Coolant Temperature multiplier"
      columnLabel = "Coolant", "Multiplier"
      xAxis       =  -40, 120, 10
      yAxis       =  0,  5, 10
      xBins       = crankingFuelBins, coolant
      yBins       = crankingFuelCoef
      gauge       = CLTGauge

	curve = crankingTpsCurve, "Cranking TPS Multiplier"
      columnLabel = "TPS", "Multiplier"
      xAxis       =  -40, 120, 10
      yAxis       =  0,  5, 10
      xBins       = crankingTpsBins, TPSValue
      yBins       = crankingTpsCoef
      gauge       = TPSGauge

	curve = crankingDurationCurve, "Cranking Duration Multiplier"
      columnLabel = "Engine Cycle", "Multiplier"
      xAxis       =  0, 1000, 10
      yAxis       =  0,  5, 10
      xBins       = crankingCycleBins
      yBins       = crankingCycleCoef


	curve = cltIdleCurve, "Warmup Idle multipplier"
      columnLabel = "Coolant", "Multiplier"
      xAxis       = -40, 120, 10
      yAxis       =  0,  50, 100
      xBins       = cltIdleCorrBins, coolant
      yBins       = cltIdleCorr
      gauge       = CLTGauge

	curve = warmupTargetAfrCurve, "CLT-based target AFR"
      columnLabel = "Coolant", "Correction"
      xAxis       = -40, 120, 10
      yAxis       =  0,  50, 100
      xBins       = warmupTargetAfrBins, coolant
      yBins       = warmupTargetAfr
      gauge       = CLTGauge

    curve = wueAfrTargetOffsetCurve, "AFR Target Temperature Adjustment"
      columnLabel = "Coolant", "AFR Offset"
      xAxis       = -40, 200, 9
      yAxis       =   -3,  1, 5
      xBins       = cltFuelCorrBins, coolant
      yBins       = wueAfrTargetOffset
      ;gauge      = cltGauge

    curve = wueAnalyzer_warmup_curve, "Warmup Enrichment"
      columnLabel = "Coolant", "Current WUE", "Coolant", "Corrected"
      xAxis       = -40, 200, 9
      yAxis       =   90,  500, 6
      xBins       = cltFuelCorrBins, coolant
      yBins       = cltFuelCorr
      yBins       = wueAnalRecommend
      ;gauge       = cltGauge
          
      lineLabel   = "Warmup Correction"
      lineLabel   = "Recommended WUE"

[TableEditor]
   ;       table_id,    map3d_id,    "title",      page

   table = fuelTableMAFTbl,  fuelTableMAFMap,  "Fuel Table",   1
      ;       constant, variable
      xBins       = fuelRpmBins,  RPMValue
      yBins       = fuelLoadBins,  MAFValue
      zBins       = fuelTable
;      gridHeight  = 2.0
      gridOrient  = 250,   0, 340 ; Space 123 rotation of grid in degrees.
      upDownLabel = "(RICHER)", "(LEANER)"

   table = fuelTableTPSTbl,  fuelTableTPSMap,  "Fuel Table",   1
      ;       constant, variable
      xBins       = fuelRpmBins,  RPMValue
      yBins       = fuelLoadBins,  TPSValue
      zBins       = fuelTable
;      gridHeight  = 2.0
      gridOrient  = 250,   0, 340 ; Space 123 rotation of grid in degrees.
      upDownLabel = "(RICHER)", "(LEANER)"

   table = fuelTableELTbl,  fuelTableELMap,  "Fuel Table",   1
      ;       constant, variable
      xBins       = fuelRpmBins,  RPMValue
      yBins       = fuelLoadBins,  engineLoad
      zBins       = fuelTable
;      gridHeight  = 2.0
      gridOrient  = 250,   0, 340 ; Space 123 rotation of grid in degrees.
      upDownLabel = "(RICHER)", "(LEANER)"

   table = tpsTpsAccelTbl,  tpsTpsAccelMap,  "TPS/TPS Acceleration Extra Fuel",   1
      xBins       = tpsTpsAccelFromRpmBins,  TPSValue
      yBins       = tpsTpsAccelToRpmBins,  TPSValue
      zBins       = tpsTpsAccelTable
    
      
   table = fsioTable1Tbl,  fsioTable1Map,  "FSIO Table #1",   1
      xBins       = fsioTable1RpmBins,  RPMValue
      yBins       = fsioTable1LoadBins,  engineLoad
      zBins       = fsioTable1

   table = fsioTable2Tbl,  fsioTable2Map,  "FSIO Table #2",   1
      xBins       = fsioTable2RpmBins,  RPMValue
      yBins       = fsioTable2LoadBins,  engineLoad
      zBins       = fsioTable2

   table = fsioTable3Tbl,  fsioTable3Map,  "FSIO Table #3",   1
      xBins       = fsioTable3RpmBins,  RPMValue
      yBins       = fsioTable3LoadBins,  engineLoad
      zBins       = fsioTable3

   table = fsioTable4Tbl,  fsioTable4Map,  "FSIO Table #4",   1
      xBins       = fsioTable4RpmBins,  RPMValue
      yBins       = fsioTable4LoadBins,  engineLoad
      zBins       = fsioTable4

   table = baroCorrTbl,  baroCorrMap,  "Baro Correction",   1
      ;       constant, variable
      xBins       = baroCorrRpmBins,  RPMValue
      yBins       = baroCorrPressureBins,  baroPressure
      zBins       = baroCorrTable
;      gridHeight  = 2.0
      gridOrient  = 250,   0, 340 ; Space 123 rotation of grid in degrees.
      upDownLabel = "(RICHER)", "(LEANER)"

   table = ignitionTableTbl,  ignitionTableMap,  "Ignition Table",   1
      ;       constant, variable
      xBins       = ignitionRpmBins,  RPMValue
#if   FA_PLAIN_MAF
      yBins       = ignitionLoadBins,  MAFValue
#elif FA_TPS
      yBins       = ignitionLoadBins,  TPSValue
#else
      yBins       = ignitionLoadBins,  engineLoad
#endif

      zBins       = ignitionTable
;      gridHeight  = 2.0
      gridOrient  = 250,   0, 340 ; Space 123 rotation of grid in degrees.
      upDownLabel = "(RICHER)", "(LEANER)"
	
   table = ignitionIatCorrTableTbl,  ignitionIatCorrTableMap,  "Ignition Intake Air Temp correction",   1
      ;       constant, variable
      xBins       = ignitionIatCorrRpmBins,  RPMValue
      yBins       = ignitionIatCorrLoadBins,  intake
      zBins       = ignitionIatCorrTable
;      gridHeight  = 2.0
      gridOrient  = 250,   0, 340 ; Space 123 rotation of grid in degrees.
      upDownLabel = "(RICHER)", "(LEANER)"

   table = veTableTbl,  veTableMap,  "VE Table",   1
      ;       constant, variable
      xBins       = veRpmBins,  RPMValue
      yBins       = veLoadBins,  MAPValue
      zBins       = veTable
;      gridHeight  = 2.0
      gridOrient  = 250,   0, 340 ; Space 123 rotation of grid in degrees.
      upDownLabel = "(RICHER)", "(LEANER)"


   table = injPhaseTableTbl,  injPhaseTableMap,  "Injection Phase",   1
      ;       constant, variable
      xBins       = injPhaseRpmBins,  RPMValue
      yBins       = injPhaseLoadBins,  engineLoad
      zBins       = injectionPhase
;      gridHeight  = 2.0
      gridOrient  = 250,   0, 340 ; Space 123 rotation of grid in degrees.
      upDownLabel = "(Later)", "(Sooner)"

   table = afrTableTbl,  afrTableMap,  "Target AFR Table",   1
      ;       constant, variable
      xBins       = afrRpmBins,  RPMValue
      yBins       = afrLoadBins,  MAPValue
      zBins       = afrTable
;      gridHeight  = 2.0
      gridOrient  = 250,   0, 340 ; Space 123 rotation of grid in degrees.
      upDownLabel = "(RICHER)", "(LEANER)"

[GaugeConfigurations]

   ;Name               Var            Title                 Units        Lo      Hi      LoD    LoW       HiW   HiD    vd  ld
#if CELSIUS
   tChargeGauge          = tCharge,     "Charge Temp",        "<22>C",      -40,    140,     -15,      1,      95,   110,   1,   1
#else
   tChargeGauge          = tCharge,     "Charge Temp",        "<22>F",      -40,    285,       5,     35,     205,   230,  1,   1
#endif


;   warmupEnrichGauge = warmupEnrich, "Warmup Enrichment",    "%",      100,    150,      -1,     -1,     101,   105,   0, 0
;   accelEnrichGauge  = accDecEnrich, "Accel Enrich",         "%",       50,    150,      -1,     -1,     999,   999,   0, 0
   egt1Gauge         = egt1, "EGT#1", "C", 0, 2000
   egt2Gauge         = egt2, "EGT#2", "C", 0, 2000
   egt3Gauge         = egt3, "EGT#3", "C", 0, 2000
   egt4Gauge         = egt4, "EGT#4", "C", 0, 2000
   egt5Gauge         = egt5, "EGT#5", "C", 0, 2000
   egt6Gauge         = egt6, "EGT#6", "C", 0, 2000
   egt7Gauge         = egt7, "EGT#7", "C", 0, 2000
   egt8Gauge         = egt8, "EGT#8", "C", 0, 2000
   rpmAccelerationGa = rpmAcceleration,     "rpm delta",        "dRpm",        0,      3,       0,      1,       3,     4,   1,   1
   massAirFlowValueGa = massAirFlowValue,"Air Flow",       "kg/hr",        0,     50,    -999,   -999,     999,   999,   1,   1
   veValueGauge      = veValue,                 "fuel: VE",            "",        0,    120,      10,     10,     100,   100,   1,   1
   baroCorrectionGauge  = baroCorrection,"BaroCorr",           "%",        0,    120,      10,     10,     100,   100,   1,   1
   knockCountGauge   = knockCount,"Knock count",           "count",        0,    120,      10,     10,     100,   100,   1,   1
   knockLevelGauge   = knockLevel,"Knock level",           "volts",        0,      7,      10,     10,     100,   100,   1,   2
   
   triggerErrorsCounterGauge = triggerErrorsCounter, "trg err", "count",     0,   15000,     0,    0,    6000,  6000,   0,   0
   
   
   idleAirValvePositionGauge = idleAirValvePosition, "idle position", "%",     0,   100,     0,    0,    100,  100,   0,   0

   speedToRpmRatioGauge = speedToRpmRatio, "speed2rpm", "",     0,   100,     0,    0,    100,  100,   4,   4
   warningCounterGauge = warningCounter, "warn", "",     0,   100,     0,    0,    100,  100,   0,   0
   lastErrorCodeGauge = lastErrorCode, "error", "",     0,   8000,     0,    0,    8000,  8000,   0,   0
   
gaugeCategory = Debug  
   debugFloatField1Gauge = debugFloatField1, @@GAUGE_NAME_DEBUG_F1@@, "%",     0,   100,     0,    0,    100,  100,   4,   4
   debugFloatField2Gauge = debugFloatField2, @@GAUGE_NAME_DEBUG_F2@@, "%",     -100,   100,     0,    0,    100,  100,   4,   4
   debugFloatField3Gauge = debugFloatField3, @@GAUGE_NAME_DEBUG_F3@@, "%",     -100,   100,     0,    0,    100,  100,   4,   4
   debugFloatField4Gauge = debugFloatField4, @@GAUGE_NAME_DEBUG_F4@@, "%",     0,   100,     0,    0,    100,  100,   4,   4
   debugFloatField5Gauge = debugFloatField5, @@GAUGE_NAME_DEBUG_F5@@, "%",     0,   100,     0,    0,    100,  100,   4,   4
   debugFloatField6Gauge = debugFloatField6, @@GAUGE_NAME_DEBUG_F6@@, "%",     -100,   100,     0,    0,    100,  100,   4,   4
   debugFloatField7Gauge = debugFloatField7, @@GAUGE_NAME_DEBUG_F7@@, "%",     0,   100,     0,    0,    100,  100,   4,   4
   debugIntField1Gauge = debugIntField1, "debug i1: pParam", "%",     0,   100,     0,    0,    100,  100,   0,   0
   debugIntField2Gauge = debugIntField2, "debug i2: offset", "%",     0,   100,     0,    0,    100,  100,   0,   0
   debugIntField3Gauge = debugIntField3, "debug i3", "%",     0,   100,     0,    0,    100,  100,   0,   0
   
gaugeCategory = Sensors  
   RPMGauge        = RPMValue,           "Engine Speed",       "RPM",       0,   15000,     200,    500,    6000,  6000,   0,   0
#if CELSIUS
   CLTGauge          = coolant,       "Coolant Temp",        "<22>C",      -40,    140,     -15,      1,      95,   110,   1,   1
#else
   CLTGauge          = coolant,       "Coolant Temp",        "<22>F",      -40,    285,       5,     35,     205,   230,   1,   1
#endif
#if CELSIUS
   IATGauge          = intake,     "Intake Air Temp",        "<22>C",      -40,    140,     -15,      1,      95,   110,   1,   1
#else
   IATGauge          = intake,     "Intake Air Temp",        "<22>F",      -40,    285,       5,     35,     205,   230,  1,   1
#endif
   TPSGauge			 = TPSValue,      "Throttle Position",         "%",        0,    100,       0,      0,     100,   100,   2,   2
   afr1Gauge         = AFRValue, "Air:Fuel Ratio 1",          "",       10,   19.4,      12,     13,      15,    16,   2,   2
   MAFGauge			 = MAFValue,          "Mass Air Flow",         "v",        0,      5,       0,      1,       3,     4,   1,   1
   VBattGauge        = VBatt,      "Battery Voltage",         "V",        8,     21,       9,     10,      17,    19,   1,   1
   MAPGauge     	 = MAPValue,               "MAP",       "kPa",        0,    300,      10,     10,     200,   200,   0,   0	
   OilPressGauge   	 = oilPressure,   "Oil Pressure",       "kPa",        0,    750,      35,     75,     550,   700,   0,   0	
   tpsADCGauge       = tpsADC,             "tps ADC",       "ADC",        0,   1024,       0,      0,       0,     0,   0,   0	
   atmPresCGauge     = baroPressure,          "Baro",       "kPa",        0,   1024,       0,      0,       0,     0,   0,   0	
   vvtPositionGauge = vvtPosition, "VVT position", "deg",     0,   100,     0,    0,    720,  720,   0,   0
   internalMcuTemperatureGauge = internalMcuTemperature, "internal temperature", "C",     0,   100,     0,    0,    100,  100,   0,   0
   VSSGauge          = vehicleSpeedKph,     "Speed",         "kmh",        0,    200,       0,      1,       3,     4,   1,   1
   pedalPositionGauge = pedalPosition,"Throttle Pedal Position",        "%",        0,    120,      10,     10,     100,   100,   1,   1
   accelerationXGauge = accelerationX,       @@GAUGE_NAME_ACCEL_X@@,      "acc",        -11,   11,     1.0,    1.2,      100,    100,   3, 1
   accelerationYGauge = accelerationY,       @@GAUGE_NAME_ACCEL_Y@@,      "acc",        -11,   11,     1.0,    1.2,      100,    100,   3, 1

gaugeCategory = Spark Data  
   ignadvGauge = ignitionAdvance,       "Ignition Advance 1",   "degrees",     -100,    100,    -999,   -999,     999,   999,   1, 1
   dwellGauge        = sparkDwellValue,           "Dwell",      "mSec",        0,     10,     0.5,    1.0,     6.0,   8.0,   1, 1
   coilDutyCycleGauge = coilDutyCycle,       @@GAUGE_NAME_DWELL_DUTY@@,      "perc",        -11,   11,     1.0,    1.2,      100,    100,   3, 1

gaugeCategory = Accel Data
   engineLoadDeltaGauge = engineLoadDelta,"fuel: load change","value",      0,    120,      10,     10,     100,   100,   1,   1
   engineLoadAccelExtraGauge = engineLoadAccelExtra,"fuel: load extra","value",      0,    120,      10,     10,     100,   100,   1,   1
   deltaTpsGauge     = deltaTps,                "fuel: TPS change",            "",        0,    120,      10,     10,     100,   100,   1,   1
   tpsAccelFuelGauge = tpsAccelFuel,"fuel: TPS enrich",             "ms",        0,    120,      10,     10,     100,   100,   1,   1
   wallFuelAmountGauge = wallFuelAmount, "fuel: wall amount", "ms",     0,   100,     0,    0,    100,  100,   0,   0
   wallFuelCorrectionGauge = wallFuelCorrection, "fuel: wall correction extra", "ms",     0,   100,     0,    0,    100,  100,   0,   0


gaugeCategory = Fuel Data
   crankingFuelGauge = crankingFuel,   "fuel: crank Width",      "mSec",        0,   25.5,     1.0,    1.2,      20,    25,   3, 1
   iatCorrectionGauge = iatCorrection, @@GAUGE_NAME_FUEL_IAT_CORR@@, "mult",     0,   3,     0,    0,    3,  3,   2,   2
   cltCorrectionGauge = cltCorrection, @@GAUGE_NAME_FUEL_CLT_CORR@@, "mult",     0,   3,     0,    0,    3,  3,   2,   2
   injectorDutyCycleGauge=injectorDutyCycle, @@GAUGE_NAME_FUEL_INJ_DUTY@@,"%",      0,    120,      10,     10,     100,   100,   1,   1
   actualLastInjectionGauge   = actualLastInjection,     @@GAUGE_NAME_FUEL_LAST_INJECTION@@, "mSec",        0,   25.5,     1.0,    1.2,      20,    25,   3, 1
   
   fuelRunningGauge     = fuelRunning,       @@GAUGE_NAME_FUEL_RUNNING@@,      "mSec",        0,   25.5,     1.0,    1.2,      20,    25,   3, 1
   baseFuelGauge     = baseFuel,       @@GAUGE_NAME_FUEL_BASE@@,      "mSec",        0,   25.5,     1.0,    1.2,      20,    25,   3, 1
   fuelPidCorrectionGauge = fuelPidCorrection,       @@GAUGE_NAME_FUEL_PID_CORR@@,      "mSec",        -11,   11,     1.0,    1.2,      20,    25,   3, 1
   

[WueAnalyze]
    
;                    wueCurveName, afrTempCompensationCurve, lambdaTargetTableName, lambdaChannel, coolantTempChannel, egoCorrectionChannel, wueChannel, activeCondition
     wueAnalyzeMap = wueAnalyzer_warmup_curve, wueAfrTargetOffsetCurve, afrTableTbl, AFRValue, coolant, cltCorrection, egoCorrection

     lambdaTargetTables = afrTableTbl, afrTSCustom

     wuePercentOffset = 0 ; for working with 0 based enrichment set to 100
     option = disableLiveUpdates
     option = burnOnSend

;     filter = std_DeadLambda ; Auto build

     filter = decelFilterMap,"After Start Enrich", engine,         &     , 4 ,       , false
     filter = accelFilterTp, "TP Accel Enrich"   , engine,         &     , 16,       , false
     filter = decelFilterTp, "TP Decel Enrich"   , engine,         &     , 32,       , false
     filter = accelFilterMap,"MAP Accel Enrich"  , engine,         &     , 64,       , false
     filter = decelFilterMap,"MAP Decel Enrich"  , engine,         &     , 128,      , false
     ; this works, just another way to skin a cat
     ;filter = decelFilter, "Decel Flag" , tpsaccden,         >       , 0,        , false
     filter = overrunFilter, "Overrun"    , pulseWidth1,  =       , 0,            , false
     filter = highThrottle, "High Throttle"    , throttle,  >       , 15,         , true
     filter = lowRpm,       "Low RPM"    ,       rpm,       <       , 300,        , false
     filter = std_Custom ; Standard Custom Expression Filter.

   
[FrontPage]
   ; Gauges are numbered left to right, top to bottom.
   ;
   ;    1  2  3  4
   ;    5  6  7  8

   ; currently a minimum of 6 gauges must be on the dash, this appears to be an old not needed limitation. next release 1 will work.
   gauge1 = RPMGauge
   gauge2 = CLTGauge
   gauge3 = TPSGauge
   gauge4 = MAFGauge
   gauge5 = afr1Gauge
   gauge6 = VBattGauge
   gauge7 = dwellGauge
   gauge8 = ignadvGauge
   


;         =   expression,            off-label,            on-label,            off-bg, off-fg, on-bg, on-fg
	; important status
    indicator = { ind_hasFatalError }, "",   "FATAL ERROR",   green, black, red,   black
    indicator = { firmwareTsVersion == fileVersion }, "WRONG VERSION",   "version",   red, black, green,   black
    indicator = { ind_isWarnNow }, "",   "warn",   green, black, red,   black
    indicator = { ind_check_engine }, "ok",      "Check engine",       green,  black,  red, black
    indicator = { isIgnitionEnabledIndicator}, "no ignition",   "ignition",   red, black, green,   black
    indicator = { ind_injection_enabled}, "no injection",   "injection",   red, black, green,   black
    indicator = { ind_isTriggerError}, "ok",      "trg err",       green,  black,  red, black
    

	; minor info	
    indicator = { ind_fan}, "no fan",   "fan",   white, black, green,   black
    indicator = { isCylinderCleanupActivated}, "no cyl cleanup",   "cyl cleanup",   white, black, green,   black    
    indicator = { needBurn }, "config ok",  "unsaved changes",   white, black, yellow,   black
    indicator = { hasSdCard}, "no SD",   "with SD",   white, black, green,   black
    indicator = { ind_fuel_pump}, "no pump",   "pump",   white, black, green,   black
    indicator = { clutchUpState }, "clutch",   "cltch Up",   white, black, red,   black
    indicator = { clutchDownState }, "clutch",   "cltch Down",   white, black, red,   black
    indicator = { brakePedalIndicator }, "brake",   "brake down",   white, black, red,   black
    
    ; error codes
    indicator = { ind_tps_error}, "tps",   "tps error",   white, black, red,   black
    indicator = { ind_clt_error}, "clt",   "clt error",   white, black, red,   black
    indicator = { ind_iat_error}, "iat",   "iat error",   white, black, red,   black
    indicator = { ind_map_error}, "map",   "map error",   white, black, red,   black

    indicator = { knockEverIndicator }, "",   "Knock recently",   white, black, red,   black
    indicator = { knockNowIndicator }, "no knock",   "Knock NOW",   white, black, red,   black
   

[Datalog]
   ;       Channel          Label          Type    Format
   entry = time,            "Time",        float,  "%.3f"
   entry = RPMValue,        "RPM",         int,    "%d"
   entry = firmwareVersion, @@GAUGE_NAME_VERSION@@,     int,    "%d"
   entry = coolant,         "CLT",         float,  "%.2f"
   entry = intake,          "IAT",         float,  "%.2f"
   entry = oilPressure,		"Oil Press",   float,  "%.1f"
   entry = TPSValue,             "TPS",         float,  "%.2f"
   entry = MAFValue,             "MAF",         float,  "%.2f"
   entry = MAPValue,        "MAP",         float,  "%.1f"
   entry = AFRValue,       @@GAUGE_NAME_AFR@@,         float,  "%.2f"
   entry = VBatt,           @@GAUGE_NAME_VBAT@@,       float,  "%.2f"
   entry = engineLoad,	    @@GAUGE_NAME_ENGINE_LOAD@@, 	   float,  "%.1f"
   entry = ignitionAdvance,	@@GAUGE_NAME_TIMING_ADVANCE@@,	   float,  "%.2f"
   entry = knockLevel,	    @@GAUGE_NAME_KNOCK_LEVEL@@, 	   float,  "%.2f"
   entry = vehicleSpeedKph,	@@GAUGE_NAME_VVS@@,	   float,  "%.2f"
   entry = speedToRpmRatio, "s2rpm",	   float,  "%.3f"
   entry = rpmAcceleration, "dRPM",        float,  "%.3f"
   entry = massAirFlowValue,"airMass",     float,  "%.3f"
   entry = pedalPosition,   "pedal",       float,  "%.3f"
   entry = triggerErrorsCounter, "trg err",int,    "%d"
   entry = idleAirValvePosition, @@GAUGE_NAME_IAC@@, float,  "%.3f"


   entry = fuelRunning,     @@GAUGE_NAME_FUEL_RUNNING@@, float,  "%.3f"
   entry = actualLastInjection,     @@GAUGE_NAME_FUEL_LAST_INJECTION@@, float,  "%.3f"
   entry = baseFuel,	    "fuel: base",  float,  "%.2f"
   entry = fuelPidCorrection,"fuel: pid",  float,  "%.2f"
   entry = veValue,         @@GAUGE_NAME_FUEL_VR@@,    float,  "%.3f"
   entry = injectorDutyCycle,@@GAUGE_NAME_FUEL_INJ_DUTY@@,float,"%.3f"
   entry = coilDutyCycle,	@@GAUGE_NAME_DWELL_DUTY@@,	float,"%.3f"
   entry = currentTargetAfr,@@GAUGE_NAME_TARGET_AFR@@,	float,"%.3f"

   entry = accelerationX,	@@GAUGE_NAME_ACCEL_X@@,	float,"%.2f"
   entry = accelerationY,	@@GAUGE_NAME_ACCEL_Y@@,	float,"%.2f"

   entry = engineLoadAccelExtra, @@GAUGE_NAME_FUEL_EL_EXTRA@@,float,  "%.3f"
   entry = engineLoadDelta, "fuel: load change",float,  "%.3f"

   entry = deltaTps,		"fuel: TPS change",float,  "%.3f"
   entry = tpsAccelFuel,    @@GAUGE_NAME_FUEL_TPS_EXTRA@@,    float,  "%.3f"

   entry = wallFuelCorrection,"fuel: wall corr ms",	float,   "%.3f"
   entry = wallFuelAmount, "fuel: wall amount",	float,   "%.3f"
   
   entry = baroCorrection,   "baroCorrection",float,"%.3f"
   entry = iatCorrection,   @@GAUGE_NAME_FUEL_IAT_CORR@@,	float,   "%.3f"
   entry = cltCorrection,	@@GAUGE_NAME_FUEL_CLT_CORR@@, float,"%.3f"

   entry = sparkDwellValue,	@@GAUGE_COIL_DWELL_TIME@@, float,"%.3f"
   entry = vvtPosition, @@GAUGE_NAME_VVT@@, float,"%.2f"

; is there a way to log parameter?   entry = debugMode,   "debugMode",int,"%d"
; Alternator_PID: alternator duty cycle
; DBG_TPS_ACCEL: from TPS 
   entry = debugFloatField1,   @@GAUGE_NAME_DEBUG_F1@@,float,"%.4f"

; Alternator_PID: current integration term
; DBG_TPS_ACCEL: to TPS
   entry = debugFloatField2,   @@GAUGE_NAME_DEBUG_F2@@,float,"%.4f"
   
; Alternator_PID: previous error
; DBG_TPS_ACCEL: tps<>tps table value
   entry = debugFloatField3,   @@GAUGE_NAME_DEBUG_F3@@,float,"%.4f"
   
; Alternator_PID: I setting
; DBG_TPS_ACCEL: extra fuel   
   entry = debugFloatField4,   @@GAUGE_NAME_DEBUG_F4@@,float,"%.4f"

; Alternator_PID: D setting
   entry = debugFloatField5,   @@GAUGE_NAME_DEBUG_F5@@,float,"%.4f"

; Alternator_PID: dTerm
   entry = debugFloatField6,   @@GAUGE_NAME_DEBUG_F6@@,float,"%.4f"
   
   entry = debugFloatField7,   @@GAUGE_NAME_DEBUG_F7@@,float,"%.4f"


; Alternator_PID: P setting
   entry = debugIntField1,   @@GAUGE_NAME_DEBUG_I1@@,int,"%d"

; Alternator_PID: offset setting
   entry = debugIntField2,   @@GAUGE_NAME_DEBUG_I2@@,int,"%d"
   
; Alternator_PID: PID reset counter   
   entry = debugIntField3,   @@GAUGE_NAME_DEBUG_I3@@,int,"%d"
   
      
   entry = engineMode,   "mode",int,"%d"
   entry = warningCounter,   @@GAUGE_NAME_WARNING_COUNTER@@,int,"%d"
   entry = lastErrorCode,   @@GAUGE_NAME_WARNING_LAST@@,int,"%d"
   entry = internalMcuTemperature,   @@GAUGE_NAME_CPU_TEMP@@,float,"%.2f"
   
   entry = tCharge, "tCharge",float,"%.3f"
   
   entry = clutchUpState,   @@INDICATOR_NAME_CLUTCH_UP@@,int,"%d"
   entry = clutchDownState,   @@INDICATOR_NAME_CLUTCH_DOWN@@,int,"%d"
   entry = brakePedalIndicator,   @@INDICATOR_NAME_BRAKE_DOWN@@,int,"%d"
   entry = ind_fan, "radiator fan",int,"%d"
   
   
;     tpsADC          = U16,    "ADC",
;     alignmet        = U16,    "al",
;     atmPres         = F32,    "pres",
;	  crankingFuel    = F32,    "ms",
;     tCharge         = F32,    "T",
;     sparkDwell      = F32,    "MAP",
;     warmUpEnrich    = F32,    "%",

[Menu]

	menu = "Engine"
		subMenu = engineChars,				"Base Engine Settings"
		subMenu = triggerConfiguration,		"Trigger Configuration"
		subMenu = std_separator
		subMenu = injectionSettings,		"Injection Settings"
		subMenu = ignitionSettings,			"Ignition Settings"
		subMenu = std_separator
		subMenu = analogInputs,				"Analog inputs"
		subMenu = cltSensor,				"CLT Sensor Settings"
		subMenu = iatSensor,				"IAT Sensor Settings"
		subMenu = auxTempSensor1Sensor,		"AuxTemp1 Sensor Settings"
		subMenu = auxTempSensor2Sensor,		"AuxTemp2 Sensor Settings"
		subMenu = mapSettings,				"MAP Sensor Settings"
		subMenu = mafDecodingCurve,			"MAF Sensor Settings"
		subMenu = egoSettings,				"EGO Sensor Settings"
		subMenu = narrowToWideOxygenCurve,	"Narrow to Wideband approximation"
		subMenu = egtInputs,				"EGT inputs"
		subMenu = oilPressureSensor,		"Oil Pressure Sensor Settings"
		subMenu = energySystems,			"Battery and Alternator Settings"
		subMenu = auxPidDialog,				"Aux PID"
		subMenu = speedSensor,				"Speed Sensor Settings"
		subMenu = tachSettings,				"Tachometer output"
		subMenu = std_separator
		subMenu = fanSetting,				"Fan Settings"
		subMenu = idleSettings,				"Idle Settings"
		subMenu = mainRealay,				"Main Relay Settings"
		subMenu = fuelPump,					"Fuel Pump Settings"
		subMenu = malfunction,				"MIL Settings"
		subMenu = hipFunction,				"hip9011 Settings (knock decoder) (alpha version)"
		subMenu = cj125Function,			"CJ125 Settings (wbo decoder)"
		subMenu = spiFunction,				"SPI Settings"
		subMenu = etbDialog,				"Electronic Thtottle Body (alpha version)"
	menu = "Tuning"
		subMenu = generalSettings,			"General"
		subMenu = monitoringSettings,		"rusEfi Console Settings"
		subMenu = std_separator
		subMenu = crankingDialog,           "Cranking"
		subMenu = crankingCltCurve,	    	"Cranking Coolant Temp Multiplier"
		subMenu = crankingTpsCurve,	    	"Cranking TPS Multiplier"
		subMenu = crankingDurationCurve,	"Cranking Duration Multiplier"
		subMenu = std_separator
		subMenu = warmupFuelDialog,			"Warmup fuel closed-loop"
		subMenu = cltFuelCorrCurve,			"Warmup fuel manual Multiplier", 0, {useWarmupPidAfr == 0}
		subMenu = warmupTargetAfrCurve,		"Warmup fuel auto correction AFR target", 0, {useWarmupPidAfr == 1}
		subMenu = cltIdleCurve,				"Warmup Idle multipplier"
		subMenu = cltTimingCorrCurve,		"Warmup timing correction"
		subMenu = std_separator
		subMenu = fuelTableDialog,			"Fuel Table", 0, {fuelAlgorithm != LM_SPEED_DENSITY}
        subMenu = veTableDialog,           	"VE Table", 0, {fuelAlgorithm == LM_SPEED_DENSITY}
        subMenu = afrTableTbl,          	"Target AFR Table", 0, {fuelAlgorithm == LM_SPEED_DENSITY}
		subMenu = iatFuelCorrCurve,			"Intake air temperature fuel Multiplier"
        subMenu = injPhaseTableTbl,         "Injection Phase"           
        subMenu = mapAccelTaper,			"Engine Load Acceleration Enrichment Taper"
		subMenu = std_separator
		subMenu = fuelClosedLoopDialog, 	"Fuel closed-loop correction"
		subMenu = AccelEnrich,				"Accel/Decel Enrichment/Enleanment"
        subMenu = tpsTpsAccelTbl, 			"TPS/TPS Acceleration Extra Fuel"
		subMenu = std_separator
		subMenu = ignitionTableTbl,			"Ignition Table"
		subMenu = ignitionIatCorrTableTbl,	"Ignition Intake Air Temp correction"
		subMenu = baroCorrTbl,				"Baro Correction", 0, {fuelAlgorithm == LM_SPEED_DENSITY}
		subMenu = std_separator
		subMenu = std_realtime,    "&Realtime Display",              0
		subMenu = tChargeSettings, "tCharge Settings"
		
	menu = "3D Map Tuning"
;		subMenu = std_realtime,				"Realtime Display"
;		subMenu = std_warmup,				"Warmup Wizard"
		subMenu = fuelTableELMap,			"Fuel Table", 0, {fuelAlgorithm != 3}
		subMenu = veTableDialog3D,			"VE Table", 0, {fuelAlgorithm == 3}
		subMenu = afrTableMap,				"Target AFR Table", 0, {fuelAlgorithm == 3}
		subMenu = injPhaseTableMap,			"Injection Phase"
		subMenu = ignitionTableMap,			"Ignition Table"
		subMenu = ignitionIatCorrTableMap,	"Ignition Intake Air Temp correction"

	menu = "Racing Features"
		subMenu = smLaunchControl,           "Launch Control"
		subMenu	= std_separator

	  menu = "Board"
		subMenu = fsioInputsDialog,         "FSIO inputs"
		subMenu = fsioOutputsDialog,        "FSIO outputs"
		subMenu = fsioTable1Tbl,			"FSIO Table #1"
		subMenu = fsioTable2Tbl,			"FSIO Table #2"
		subMenu = fsioTable3Tbl,			"FSIO Table #3"
		subMenu = fsioTable4Tbl,			"FSIO Table #4"
		subMenu = fsioFormulas,				"FSIO Formulas"
		subMenu = fsioCurve1,			    "FSIO Curve #1"
		subMenu = fsioCurve2,			    "FSIO Curve #2"
		subMenu = fsioCurve3,			    "FSIO Curve #3"
		subMenu = fsioCurve4,			    "FSIO Curve #4"
		subMenu	= std_separator
	 	subMenu = connection,            	"Connection"
		subMenu = joystickPanel,		"Joystick"
		subMenu = std_separator
		subMenu = ioTest,					"I-O Test"
		subMenu = ecuStimulator,			"ECU stimulator"
		subMenu = allPins,					"Full pinout"

[ControllerCommands]
; commandName    = command1, command2, commandn...
; command in standard ini format, a command name can be assigned to 1 to n commands that will be executed in order.
;         This does not include any resultant protocol envelope data, only the response data itself.

; WARNING!! These commands bypass TunerStudio's normal memory synchronization. If these commands
; alter mapped settings (Constant) memory in the controller, TunerStudio will have an out of sync condition 
; and may create error messages.
; It is expected that these commands would not typically alter any ram mapped to a Constant.

;
; see TS_IO_TEST_COMMAND in firmware code
;

cmd_test_spk1  = "w\x00\x12\x00\x01"
cmd_test_spk2  = "w\x00\x12\x00\x02"
cmd_test_spk3  = "w\x00\x12\x00\x03"
cmd_test_spk4  = "w\x00\x12\x00\x04"
cmd_test_spk5  = "w\x00\x12\x00\x05"
cmd_test_spk6  = "w\x00\x12\x00\x06"
cmd_test_spk7  = "w\x00\x12\x00\x07"
cmd_test_spk8  = "w\x00\x12\x00\x08"
cmd_test_spk9  = "w\x00\x12\x00\x09"
cmd_test_spk10 = "w\x00\x12\x00\x0a"
cmd_test_spk11 = "w\x00\x12\x00\x0b"
cmd_test_spk12 = "w\x00\x12\x00\x0c"
cmd_test_spk13 = "w\x00\x12\x00\x0d"
cmd_test_spk14 = "w\x00\x12\x00\x0e"
cmd_test_spk15 = "w\x00\x12\x00\x0f"
cmd_test_spk16 = "w\x00\x12\x00\x10"
		
		
cmd_test_inj1  = "w\x00\x13\x00\x01"
cmd_test_inj2  = "w\x00\x13\x00\x02"
cmd_test_inj3  = "w\x00\x13\x00\x03"
cmd_test_inj4  = "w\x00\x13\x00\x04"
cmd_test_inj5  = "w\x00\x13\x00\x05"
cmd_test_inj6  = "w\x00\x13\x00\x06"
cmd_test_inj7  = "w\x00\x13\x00\x07"
cmd_test_inj8  = "w\x00\x13\x00\x08"
cmd_test_inj9  = "w\x00\x13\x00\x09"
cmd_test_inj10 = "w\x00\x13\x00\x0a"
cmd_test_inj11 = "w\x00\x13\x00\x0b"
cmd_test_inj12 = "w\x00\x13\x00\x0c"
cmd_test_inj13 = "w\x00\x13\x00\x0d"
cmd_test_inj14 = "w\x00\x13\x00\x0e"
cmd_test_inj15 = "w\x00\x13\x00\x0f"
cmd_test_inj16 = "w\x00\x13\x00\x10"
		
cmd_test_fuel_pump           = "w\x00\x14\x00\x01"
cmd_test_radiator_fan        = "w\x00\x15\x00\x01"
cmd_test_check_engine_light  = "w\x00\x16\x00\x01"
cmd_test_idle_valve          = "w\x00\x17\x00\x01"
cmd_call_from_pit            = "w\x00\x20\x34\x56"
cmd_stop_engine              = "w\x00\x99\x00\x00"
		
		
[UserDefined]
	dialog = fuelTableBottomDialog, "", card
		panel = fuelTableMAFTbl, Center, {fuelAlgorithm==LM_PLAIN_MAF}
		panel = fuelTableTPSTbl, Center, {fuelAlgorithm==LM_ALPHA_N}
		panel = fuelTableELTbl, Center

	dialog = fuelTableRight, "", yAxis
	 	topicHelp = "http://rusefi.com/fuel"
		displayOnlyField = "Fuel Algorithm",						fuelAlgorithm
		panel = fuelTableBottomDialog, Center
		liveGraph = fuelLive, "Fuel", South
			graphLine = AFRValue
		    graphLine = RPMValue

	dialog = fuelTableGaugesPanel, yAxis
		gauge = TPSGauge
		gauge = MAFGauge
		gauge = MAPGauge

	dialog = fuelTableDialog, "Fuel Table", xAxis
		panel = fuelTableGaugesPanel
		panel = fuelTableRight

	dialog = tChargeSettings, "tChart Settings"
		field = "MinRpm MinTps", tChargeMinRpmMinTps
		field = "MinRpm MaxTps", tChargeMinRpmMaxTps
		field = "MaxRpm MinTps", tChargeMaxRpmMinTps
		field = "MaxRpm MaxTps", tChargeMaxRpmMaxTps

	dialog = baseInjection, "Injection"
		field = "Enabled",						isInjectionEnabled
		field = "Mode",							injectionMode, {isInjectionEnabled == 1}
		field = "#Batch injection with individual wiring"
		field = "Two wire batch",				twoWireBatchInjection, {isInjectionEnabled == 1 && injectionMode == 2}

	dialog = baseIgnition, "Ignition"		
		field = "Enabled",						isIgnitionEnabled
		field = "Mode",							ignitionMode, {isIgnitionEnabled == 1}
		field = "#Wasted spark with individual coils"
		field = "Two wire wasted",				twoWireBatchIgnition, {isIgnitionEnabled == 1 && ignitionMode == 2}
		field = "Timing Mode",					timingMode, {isIgnitionEnabled == 1}
		field = "#Use fixed timing while validating with a timing gun"
		field = "Fixed Timinig",				fixedTiming, {isIgnitionEnabled == 1 && timingMode == 1}


;			Engine->Base Engine Settings
	dialog = engineChars,	"Base Engine Settings"
;		field = "Engine Preset",						engineType
		field = "Number of Cylinders",					cylindersCount
		field = "Engine Displacement",         			displacement
		field = "debug fields",							debugMode
		field = ""
		field = "Firing Order",							firingOrder
		panel = baseInjection
		panel = baseIgnition

;			Engine->Trigger configuration
	dialog = triggerConfiguration_settings,	"Settings Trigger"
		field = "Trigger type",							trigger_type
		field = "Operation mode",						operationMode
		field = "With VR sensors only rising edge has reliable position"
		field = "use only rising edge",					useOnlyRisingEdgeForTrigger    
	    field = "!Reminder that 4-stroke cycle is 720 degrees"
	    field = "Trigger Angle Offset",         		globalTriggerAngleOffset
		field = "#Custom Trigger"
		field = "total Tooth Count",					trigger_customTotalToothCount, {trigger_type == 0}
		field = "skipped Tooth Count",					trigger_customSkippedToothCount, {trigger_type == 0}

	dialog = triggerConfiguration_IO,	"Settings I/O"
		field = "!ECU reboot needed to apply pin assignment"
		field = "#Cam is primary if you have cam sensor"
		field = "Primary input channel", 				triggerInputPins1
		field = "Invert Primary",						invertPrimaryTriggerSignal
	    field = "Secondary channel", 					triggerInputPins2,            { trigger_type != 0 && trigger_type != 8 && trigger_type != 9 && trigger_type != 18 && trigger_type != 20}
	    field = "Invert Secondary",						invertSecondaryTriggerSignal, { trigger_type != 0 && trigger_type != 8 && trigger_type != 9 && trigger_type != 18 && trigger_type != 20}
	    field = "Cam Sync/VVT input",					camInput
	    field = "VVT mode",								vvtMode, {trigger_type != 80}
	    field = "VVT use rise front",					vvtCamSensorUseRise, {trigger_type != 80}
	    field = "VVT position display offset",			vvtOffset
	    field = "VVT display inverted",					vvtDisplayInverted
	    field = "NB2 from temp",						nb2ratioFrom
	    field = "NB2 to temp",							nb2ratioTo
	    field = "nbVvtIndex",							nbVvtIndex
	    field = "Trigger error LED",					triggerErrorPin
	    field = "Trigger error LED mode",				triggerErrorPinMode
	    field = "print sync details to console",		isPrintTriggerSynchDetails
	dialog = triggerConfiguration
		panel = triggerConfiguration_settings,	North
		panel = triggerConfiguration_IO,		South

;			Engine->Injection Settings
	dialog = injChars, "Injector Settings",	yAxis
		field = "Injector Flow",			injector_flow
		field = "phase offset",				extraInjectionOffset
		
	dialog = injIO, "Injector Output",	yAxis
		field = "!ECU reboot needed to apply these settings"
		field = "injection Pin Mode",       			injectionPinMode
		field = "Injection Pin 1",						injectionPins1
		field = "Injection Pin 2",						injectionPins2, {cylindersCount > 1}
		field = "Injection Pin 3",						injectionPins3, {cylindersCount > 2}
		field = "Injection Pin 4",						injectionPins4, {cylindersCount > 3}
		field = "Injection Pin 5 ",						injectionPins5, {cylindersCount > 4}
		field = "Injection Pin 6 ",						injectionPins6, {cylindersCount > 5}
		field = "Injection Pin 7 ",						injectionPins7, {cylindersCount > 6}
		field = "Injection Pin 8 ",						injectionPins8, {cylindersCount > 7}
		field = "Injection Pin 9 ",						injectionPins9, {cylindersCount > 8}
		field = "Injection Pin 10 ",	    			injectionPins10, {cylindersCount > 9}
		field = "Injection Pin 11 ",					injectionPins11, {cylindersCount > 10}
		field = "Injection Pin 12 ",					injectionPins12, {cylindersCount > 11}	
	
	dialog = injectorSetting, "", yAxis
		panel = injChars,				North
		panel = injIO,					East
		
	dialog = injectionSettings,	"",	xAxis
		panel = injectorSetting,		West
		panel = injectorsDeadTime,		East

	dialog = ignitionCylExtra, "Ignition Cyliner Extra"
		field = "Extra cyl #1",                       timing_offset_cylinder1
		field = "Extra cyl #2",                       timing_offset_cylinder2, {cylindersCount > 1}
		field = "Extra cyl #3",                       timing_offset_cylinder3, {cylindersCount > 2}
		field = "Extra cyl #4",                       timing_offset_cylinder4, {cylindersCount > 3}
		field = "Extra cyl #5",                       timing_offset_cylinder5, {cylindersCount > 4}
		field = "Extra cyl #6",                       timing_offset_cylinder6, {cylindersCount > 5}
		field = "Extra cyl #7",                       timing_offset_cylinder7, {cylindersCount > 6}
		field = "Extra cyl #8",                       timing_offset_cylinder8, {cylindersCount > 7}
		field = "Extra cyl #9",                       timing_offset_cylinder9, {cylindersCount > 8}
		field = "Extra cyl #10",                       timing_offset_cylinder10, {cylindersCount > 9}
		field = "Extra cyl #11",                       timing_offset_cylinder11, {cylindersCount > 10} 
		field = "Extra cyl #12",                       timing_offset_cylinder12, {cylindersCount > 11}


;			Engine->Ignition Settings
	dialog = ignitionOutputs, "Ignition Outputs"
		field = "Ignition Pin Mode",         	        ignitionPinMode
		field = "Ignition Pin 1",                       ignitionPins1 
		field = "Ignition Pin 2",                       ignitionPins2, {(ignitionMode != 0 && cylindersCount > 1) && (ignitionMode !=2 || twoWireBatchIgnition == 1 @@ignitionPin2logic@@)}
		field = "Ignition Pin 3",                       ignitionPins3, {(ignitionMode != 0 && cylindersCount > 2) && (ignitionMode !=2 || twoWireBatchIgnition == 1 @@ignitionPin3logic@@)}
		field = "Ignition Pin 4",                       ignitionPins4, {(ignitionMode != 0 && cylindersCount > 3) && (ignitionMode !=2 || twoWireBatchIgnition == 1 @@ignitionPin4logic@@)}
		field = "Ignition Pin 5",                       ignitionPins5, {(ignitionMode != 0 && cylindersCount > 4) && (ignitionMode !=2 || twoWireBatchIgnition == 1 @@ignitionPin5logic@@)}
		field = "Ignition Pin 6",                       ignitionPins6, {(ignitionMode != 0 && cylindersCount > 5) && (ignitionMode !=2 || twoWireBatchIgnition == 1 @@ignitionPin6logic@@)}
		field = "Ignition Pin 7",                       ignitionPins7, {(ignitionMode != 0 && cylindersCount > 6) && (ignitionMode !=2 || twoWireBatchIgnition == 1 @@ignitionPin7logic@@)}
		field = "Ignition Pin 8",                       ignitionPins8, {(ignitionMode != 0 && cylindersCount > 7) && (ignitionMode !=2 || twoWireBatchIgnition == 1 @@ignitionPin8logic@@)}
		field = "Ignition Pin 9",                       ignitionPins9, {(ignitionMode != 0 && cylindersCount > 8) && (ignitionMode !=2 || twoWireBatchIgnition == 1 @@ignitionPin8logic@@)}
		field = "Ignition Pin 10",                      ignitionPins10, {(ignitionMode != 0 && cylindersCount > 9) && (ignitionMode !=2 || twoWireBatchIgnition == 1 @@ignitionPin8logic@@)}
		field = "Ignition Pin 11",                      ignitionPins11, {(ignitionMode != 0 && cylindersCount > 10) && (ignitionMode !=2 || twoWireBatchIgnition == 1 @@ignitionPin8logic@@)}
		field = "Ignition Pin 12",                      ignitionPins12, {(ignitionMode != 0 && cylindersCount > 11) && (ignitionMode !=2 || twoWireBatchIgnition == 1 @@ignitionPin8logic@@)}
		field = "This is useful to have tachometer working while converting from distributor"
		field = "Dizzy out Pin",         	    	    dizzySparkOutputPin
		field = "Dizzy out Pin Mode",                   dizzySparkOutputPinMode 
		
	dialog = ignitionSettings, "", xAxis
		panel = ignitionOutputs,	West
		panel = dwellCorrection,	Center
		panel = ignitionCylExtra,	East
		
;			Engine->Aux1 Thermistor Settings
	dialog = auxTempSensor1_thermistor, "aux1 Thermistor Settings"
		field = "!Here is three pairs of thermistor temperature and his resistance."
		field = "!Typical temperatures is -40<34>C, 0<>C and 100<30>C"
		field = ""
		field = "Lowest temperature",  					auxTempSensor1_tempC_1		
		field = "Resistance @ LT",         	   			auxTempSensor1_resistance_1
		field = ""
		field = "Middle temperature",    		  	    auxTempSensor1_tempC_2
		field = "Resistance @ MT",         	    		auxTempSensor1_resistance_2
		field = ""
		field = "Highest temperature",				 	auxTempSensor1_tempC_3
		field = "Resistance @ HT",         	    		auxTempSensor1_resistance_3
	dialog = auxTempSensor1Sensor_IO,	"auxTempSensor1 Sensor I/O"
		field = "auxTempSensor1 ADC input",				auxTempSensor1_adcChannel
		field = "Bias Resistor Value",    	    		auxTempSensor1_bias_resistor
	dialog = auxTempSensor1Sensor, "", yAxis
		panel = auxTempSensor1_thermistor,		North
		panel = auxTempSensor1Sensor_IO,		South

;			Engine->Aux2 Thermistor Settings
	dialog = auxTempSensor2_thermistor, "aux1 Thermistor Settings"
		field = "!Here is three pairs of thermistor temperature and his resistance."
		field = "!Typical temperatures is -40<34>C, 0<>C and 100<30>C"
		field = ""
		field = "Lowest temperature",  					auxTempSensor2_tempC_1		
		field = "Resistance @ LT",         	   			auxTempSensor2_resistance_1
		field = ""
		field = "Middle temperature",    		  	    auxTempSensor2_tempC_2
		field = "Resistance @ MT",         	    		auxTempSensor2_resistance_2
		field = ""
		field = "Highest temperature",				 	auxTempSensor2_tempC_3
		field = "Resistance @ HT",         	    		auxTempSensor2_resistance_3
	dialog = auxTempSensor2Sensor_IO,	"auxTempSensor2 Sensor I/O"
		field = "auxTempSensor2 ADC input",				auxTempSensor2_adcChannel
		field = "Bias Resistor Value",    	    		auxTempSensor2_bias_resistor
	dialog = auxTempSensor2Sensor, "", yAxis
		panel = auxTempSensor2_thermistor,		North
		panel = auxTempSensor2Sensor_IO,		South


	dialog = allPins1
		field = "MAP ADC input", 						map_sensor_hwChannel
		field = "frequencyReportingMapInputPin",		frequencyReportingMapInputPin
		field = "CLT ADC input", 						clt_adcChannel
		field = "IAT ADC input", 						iat_adcChannel
		field = "vBatt ADC input", 						vbattAdcChannel
		field = "TPS ADC input", 						tpsAdcChannel
		field = "MAF ADC input", 						mafAdcChannel
		field = "AFR ADC input", 						afr_hwChannel
		field = "fuelLevelSensor", 						fuelLevelSensor
		field = "Baro ADC input", 						baroSensor_hwChannel
		field = "Throttle pedal Position Channel", 		pedalPositionChannel
		field = "Primary input channel", 				triggerInputPins1
		field = "Secondary channel", 					triggerInputPins2
		field = "Cam Sync/VVT input",					camInput
		field = "Vehicle Speed Input pin",				vehicleSpeedSensorInputPin
		field = "clutchDownPin",						clutchDownPin
		field = "clutchUpPin",							clutchUpPin
		field = "brakePedalPin",						brakePedalPin

	dialog = allPins2
		field = "Tachometer output Pin",						tachOutputPin
		field = "Dizzy out Pin",         	    	    dizzySparkOutputPin
		field = "O2 heater pin",						o2heaterPin
		field = "Idle Solenoid Pin",					idle_solenoidPin
		field = "Idle Stepper Dir",						idle_stepperDirectionPin
		field = "Idle Stepper Dir Mode",				stepperDirectionPinMode
		field = "Idle Stepper Step",					idle_stepperStepPin
		field = "Idle Stepper Enable",					stepperEnablePin
		field = "Idle Stepper Pulse",					idleStepperPulseDuration
		field = "Fuel Pump Pin",						fuelPumpPin
		field = "ETB Dir #1",							etbDirectionPin1
		field = "ETB Dir #2",							etbDirectionPin2
		field = "ETB Control #1",						etbControlPin1	
		field = "ETB Control #2",						etbControlPin2	
		field = "SD CS Pin",							sdCardCsPin
		field = "Check Engine Pin",						malfunctionIndicatorPin
		field = "Aux Pin #1",							auxPidPins1
		field = "Aux Pin #2",							auxPidPins2
		field = "Aux Pin #3",							auxPidPins3
		field = "Aux Pin #4",							auxPidPins4
		


	dialog = allPins3
		field = "Injection Pin 1",						injectionPins1
		field = "Injection Pin 2",						injectionPins2
		field = "Injection Pin 3",						injectionPins3
		field = "Injection Pin 4",						injectionPins4
		field = "Injection Pin 5 ",						injectionPins5
		field = "Injection Pin 6 ",						injectionPins6
		field = "Injection Pin 7 ",						injectionPins7
		field = "Injection Pin 8 ",						injectionPins8
		field = "Injection Pin 9 ",						injectionPins9
		field = "Injection Pin 10 ",	    			injectionPins10
		field = "Injection Pin 11 ",					injectionPins11
		field = "Injection Pin 12 ",					injectionPins12
		
		field = "Ignition Pin 1",                       ignitionPins1 
		field = "Ignition Pin 2",                       ignitionPins2
		field = "Ignition Pin 3",                       ignitionPins3
		field = "Ignition Pin 4",                       ignitionPins4
		field = "Ignition Pin 5",                       ignitionPins5
		field = "Ignition Pin 6",                       ignitionPins6
		field = "Ignition Pin 7",                       ignitionPins7
		field = "Ignition Pin 8",                       ignitionPins8
		field = "Ignition Pin 9",                       ignitionPins9
		field = "Ignition Pin 10",                      ignitionPins10
		field = "Ignition Pin 11",                      ignitionPins11
		field = "Ignition Pin 12",                      ignitionPins12

	dialog = allPins4
		field = "FSIO dig inp #1",						fsioDigitalInputs1
		field = "FSIO dig inp #2",						fsioDigitalInputs2
		field = "FSIO dig inp #3",						fsioDigitalInputs3
		field = "FSIO dig inp #4",						fsioDigitalInputs4
		field = "FSIO dig inp #5",						fsioDigitalInputs5
		field = "FSIO dig inp #6",						fsioDigitalInputs6
		field = "FSIO dig inp #7",						fsioDigitalInputs7
		field = "FSIO dig inp #8",						fsioDigitalInputs8
		field = "FSIO dig inp #9",						fsioDigitalInputs9
		field = "output #1", 							fsioOutputPins1
		field = "output #2", 							fsioOutputPins2
		field = "output #3", 							fsioOutputPins3
		field = "output #4", 							fsioOutputPins4
		field = "output #5", 							fsioOutputPins5
		field = "output #6", 							fsioOutputPins6
		field = "output #7", 							fsioOutputPins7
		field = "output #8", 							fsioOutputPins8
		field = "output #9", 							fsioOutputPins9
		field = "output #10", 							fsioOutputPins10
		field = "output #11", 							fsioOutputPins11
		field = "output #12", 							fsioOutputPins12
		field = "output #13", 							fsioOutputPins13
		field = "output #14", 							fsioOutputPins14
		field = "output #15", 							fsioOutputPins15
		field = "output #16", 							fsioOutputPins16
		field = "aux valve #1", 						auxValves1
		field = "aux valve #2", 						auxValves2



	dialog = allPins1_2, "", xAxis
		panel = allPins1
		panel = allPins2

	dialog = allPins3_4, "", xAxis
		panel = allPins3
		panel = allPins4

	dialog = allPins, "All Pins", xAxis
		panel = allPins1_2
		panel = allPins3_4


;			Engine->CLT Thermistor Settings
	dialog = clt_thermistor, "CLT Thermistor Settings"
		field = "!Here is three pairs of thermistor temperature and his resistance."
		field = "!Typical temperatures is -40<34>C, 0<>C and 100<30>C"
		field = ""
		field = "Lowest temperature",  					clt_tempC_1		
		field = "Resistance @ LT",         	   			clt_resistance_1
		field = ""
		field = "Middle temperature",    		  	    clt_tempC_2
		field = "Resistance @ MT",         	    		clt_resistance_2
		field = ""
		field = "Highest temperature",				 	clt_tempC_3
		field = "Resistance @ HT",         	    		clt_resistance_3
		field = "Is linear?",							useLinearCltSensor
	dialog = cltSensor_IO,	"CLT Sensor I/O"
		field = "CLT ADC input", 						clt_adcChannel
		field = "Bias Resistor Value",    	    		clt_bias_resistor
	dialog = cltSensor, "", yAxis
		panel = clt_thermistor,		North
		panel = cltSensor_IO,		South

;			Engine->IAT Thermistor Settings
	dialog = iat_thermistor, "IAT Thermistor Settings"
		field = "!Here is three pairs of thermistor temperature and his resistance."
		field = "!Typical temperatures is -40<34>C, 0<>C and 100<30>C"
		field = ""
		field = "Lowest temperature",                   iat_tempC_1		
		field = "Resistance @ LT",         	   			iat_resistance_1
		field = ""
		field = "Middle temperature",         	    	iat_tempC_2
		field = "Resistance @ MT",         	    		iat_resistance_2
		field = ""
		field = "Highest temperature",         	    	iat_tempC_3
		field = "Resistance @ HT",         	    		iat_resistance_3
	dialog = iatSensor_IO,	"IAT Sensor I/O"
		field = "IAT ADC input", 						iat_adcChannel
		field = "Bias Resistor Value",    	    		iat_bias_resistor
		field = "Is linear?",							useLinearIatSensor
	dialog = iatSensor, "", yAxis
		panel = iat_thermistor,		North
		panel = iatSensor_IO,		South

	dialog = oilp_settings, "Oil Pressure Sensor Settings"
		field = "low voltage",							oilPressure_v1
		field = "low pressure",							oilPressure_value1
		field = "high voltage",							oilPressure_v2
		field = "high pressure",						oilPressure_value2
	dialog = oilp_IO, "Oil Pressure Sensor I/O"
		field = "Oil Pressure ADC input",				oilPressure_hwChannel
	dialog = oilPressureSensor, "", yAxis
		panel = oilp_settings, North
		panel = oilp_IO, South

;			Engine->MAP Sensor Settings
	dialog = mapSensorVDlg, "Voltage Sensor Settings", xAxis		
	    field = "MAP ADC input", 						map_sensor_hwChannel, {hasFrequencyReportingMapSensor == 0}
		field = "Map type", map_sensor_type, 			{hasFrequencyReportingMapSensor == 0}
		field = "MAP value low point",  		        map_sensor_lowValue, { map_sensor_type == 0 && hasFrequencyReportingMapSensor == 0}
		field = "MAP voltage low point", 	 		    mapLowValueVoltage, { map_sensor_type == 0 && hasFrequencyReportingMapSensor == 0}
		field = "MAP value high point",               	map_sensor_highValue, { map_sensor_type == 0 && hasFrequencyReportingMapSensor == 0}
		field = "MAP voltage high value",               mapHighValueVoltage, { map_sensor_type == 0 && hasFrequencyReportingMapSensor == 0}
		field = "Use minimal value of",					mapMinBufferLength

	dialog = mapSensorFDlg, "Frequency Sensor Settings", xAxis		
		field = "pin",		frequencyReportingMapInputPin, {hasFrequencyReportingMapSensor == 1}
		field = "0 kPa freq",		mapFrequency0Kpa, {hasFrequencyReportingMapSensor == 1}
		field = "100 kpa freq",		mapFrequency100Kpa, {hasFrequencyReportingMapSensor == 1}

	dialog = mapCurves, "", border		
	    panel = map_samplingAngleCurve,	West
		panel = map_samplingWindowCurve,	East

	dialog = mapSwitch, "MAP input type"
	    field = "frequency-based MAP",				hasFrequencyReportingMapSensor
	    
	dialog = mapVandF, "V and F"	    
		panel = mapSensorVDlg, 		North
		panel = mapSensorFDlg,		South
	
	dialog = mapSwitchAndSettings, "Switch and Settings"
		field = "!ECU reboot needed to apply pin assignment"
		panel = mapSwitch, 		North
		panel = mapVandF,		South
		
	dialog = mapSettings, "MAP Sensor Settings", border
		panel = mapCurves,		North
		panel = mapSwitchAndSettings,		South

;			Engine->EGO Sensor Settings
	dialog = egoSettings_sensor,	"EGO Sensor Settings"
		field = "Type",									afr_type
; todo: only use these values for custom!		
		field = "low voltage", 							afr_v1
		field = "low value", 							afr_value1
		field = "high voltage", 						afr_v2
		field = "high value", 							afr_value2
		field = "Correction",							egoValueShift
	dialog = egoSettings_IO,	"EGO Sensor I/O"
		field = "AFR ADC input", 						afr_hwChannel
		field = "O2 heater pin",						o2heaterPin
	dialog = egoSettings, "", yAxis
		panel = egoSettings_sensor,	North
		panel = egoSettings_IO,		South

;			Engine->EGT inputs
	dialog = egtInputs, "EGT inputs"
		field = "SPI", 									max31855spiDevice
        field = "CS #1", 								max31855_cs1
        field = "CS #2", 								max31855_cs2
        field = "CS #3", 								max31855_cs3
        field = "CS #4", 								max31855_cs4
        field = "CS #5", 								max31855_cs5
        field = "CS #6", 								max31855_cs6
        field = "CS #7", 								max31855_cs7
        field = "CS #8", 								max31855_cs8

;			Engine->idle Settings	
	dialog = idleSolenoid, "solenoid"
		field = "Idle Solenoid Pin Mode",   	  	    idle_solenoidPinMode, !useStepperIdle
		field = "Idle Solenoid Pin",					idle_solenoidPin, !useStepperIdle
		field = "Idle Solenoid Frequency",   			idle_solenoidFrequency, !useStepperIdle
	
	dialog = idleStepper, "stepper"
		field = "Idle Stepper Step",					idle_stepperStepPin, useStepperIdle
		field = "Idle Stepper Dir",						idle_stepperDirectionPin, useStepperIdle
		field = "Idle Stepper Enable",					stepperEnablePin, useStepperIdle
		field = "Idle Stepper Enable mode",				stepperEnablePinMode, useStepperIdle
		field = "Stepper reaction time",				idleStepperReactionTime, useStepperIdle
		field = "Stepper total steps",					idleStepperTotalSteps, useStepperIdle
		
	dialog = idleType, "Type idle valve",	border
		panel = idleSolenoid,				West
		panel = idleStepper,				East
		
	dialog = idleSettings, "", yAxis
		field = "#Automatic Mode is still Alpha Version"
		field = "Manual mode",							idleMode
		field = "Cranking Idle Air",					crankingIACposition
		field = "# Warmup Idle multipplier is apploed to target RPM"
		field = "Auto target",							targetIdleRpm, { idleMode == 0}
		field = "idle P",								idleRpmPid_pFactor, { idleMode == 0}
		field = "idle I",								idleRpmPid_iFactor, { idleMode == 0}
		field = "idle D",								idleRpmPid_dFactor, { idleMode == 0}
		field = "idle offset",							idleRpmPid_offset, { idleMode == 0}
		field = "period",								idleRpmPid_period
		field = "pid min",								idleRpmPid_minValue, { idleMode == 0}
		field = "pid max",								idleRpmPid_maxValue, { idleMode == 0}
		field = "pid TPS deactivation",					idlePidDeactivationTpsThreshold, { idleMode == 0}
		field = "RPM error to deactivate IAC pid",		iacRPMErrorThreshold, { idleMode == 0}
		field = "iacByTpsTaper",						iacByTpsTaper;
		field = "verbose",								isVerboseIAC
		slider = "Manual Idle Position",				manIdlePosition, horizontal
		field = ""
		field = "use stepper",							useStepperIdle
		panel = idleType

;			Engine->Fan Settings
	dialog = fanSetting, "Fan Settings"
		field = "Fan On Temperature",					fanOnTemperature
		field = "Fan Off Temperature",					fanOffTemperature
		field = ""
		field = "!ECU reboot needed to apply these settings"
		field = "Fan Pin Mode",							fanPinMode
		field = "Fan Pin",								fanPin

;			Engine->Main Relay Settings
	dialog = mainRealay,	"Main Relay Settings"
		field = "!ECU reboot needed to apply these settings"
		field = "Main Relay Mode",			         	mainRelayPinMode	
		field = "Main Relay Pin",  						mainRelayPin
		
;			Engine->Fuel Pump Settings
	dialog = fuelPump,	"Fuel Pump Settings"
		field = "!ECU reboot needed to apply these settings"
		field = "Fuel Pump Pin Mode",         	        fuelPumpPinMode
		field = "Fuel Pump Pin",						fuelPumpPin
		
;			Engine->MIL Settings
	dialog = malfunction,	"Check Engine Settings"
		field = "!ECU reboot needed to apply these settings"
		field = "Check Engine Pin Mode",				         	malfunctionIndicatorPinMode	
		field = "Check Engine Pin",         						malfunctionIndicatorPin
		field = "Warning Period",									warningPeriod

;			Engine->hip9011 Settings
	dialog = hipFunction, "HIP9011 Settings (knock decoder)"
		field = "Enabled",								isHip9011Enabled
		field = "Threshold",							knockVThreshold, {isHip9011Enabled == 1}
		field = "!ECU reboot needed to apply these settings"
		field = "IntHold pin (hip9011 input)",      	hip9011IntHoldPin, {isHip9011Enabled == 1}
		field = "IntHold pin (hip9011 input) mode",		hip9011IntHoldPinMode, {isHip9011Enabled == 1}
		field = "ChipSelect pin",						hip9011CsPin, {isHip9011Enabled == 1}
		field = "ChipSelect mode",						hip9011CsPinMode, {isHip9011Enabled == 1}
		field = "hip Output/stm input",					hipOutputChannel, {isHip9011Enabled == 1}
		field = "prescaler & SDO",						hip9011PrescalerAndSDO, {isHip9011Enabled == 1}
		field = "Band Freq override",					knockBandCustom, {isHip9011Enabled == 1}
		field = "SPI device",							hip9011SpiDevice, {isHip9011Enabled == 1}
		field = "SPI1sck",								spi1SckMode, {isHip9011Enabled == 1}
		field = "SPI1mosi",								spi1MosiMode, {isHip9011Enabled == 1}
		field = "SPI1miso",								spi1MisoMode, {isHip9011Enabled == 1}
		field = "SPI2sck",								spi2SckMode, {isHip9011Enabled == 1}
		field = "SPI2mosi",								spi2MosiMode, {isHip9011Enabled == 1}
		field = "SPI2miso",								spi2MisoMode, {isHip9011Enabled == 1}
		field = "SPI3sck",								spi3SckMode, {isHip9011Enabled == 1}
		field = "SPI3mosi",								spi3MosiMode, {isHip9011Enabled == 1}
		field = "SPI3miso",								spi3MisoMode, {isHip9011Enabled == 1}
		panel = knockThresholdCurve
		
;			Engine->cj125 Settings
	dialog = cj125Function, "CJ125 Settings (wbo decoder)"
		field = "Enabled",								isCJ125Enabled
		field = "!ECU reboot needed to apply these settings"
		field = "ChipSelect pin",						cj125CsPin, {isCJ125Enabled == 1}
		field = "ChipSelect mode",						cj125CsPinMode, {isCJ125Enabled == 1}
		field = "SPI device",							cj125SpiDevice
		field = "UA input",								cj125ua, {isCJ125Enabled == 1}
		field = "UR input",								cj125ur, {isCJ125Enabled == 1}
		
	dialog = spiFunction, "SPI settings"
		field = "!ECU reboot needed to apply these settings"
		field = "SPI1 enable",							is_enabled_spi_1
		field = "SPI1 MOSI",							spi1mosiPin, {is_enabled_spi_1 == 1}
		field = "SPI1 MISO",							spi1misoPin, {is_enabled_spi_1 == 1}
		field = "SPI1 SCK",								spi1sckPin, {is_enabled_spi_1 == 1}
		field = "SPI2 enable",							is_enabled_spi_2
		field = "SPI2 MOSI",							spi2mosiPin, {is_enabled_spi_2 == 1}
		field = "SPI2 MISO",							spi2misoPin, {is_enabled_spi_2 == 1}
		field = "SPI2 SCK",								spi2sckPin, {is_enabled_spi_2 == 1}
		field = "SPI3 enable",							is_enabled_spi_3
		field = "SPI3 MOSI",							spi3mosiPin, {is_enabled_spi_3 == 1}
		field = "SPI3 MISO",							spi3misoPin, {is_enabled_spi_3 == 1}
		field = "SPI3 SCK",								spi3sckPin, {is_enabled_spi_3 == 1}
		field = "LIS302DLCsPin",						LIS302DLCsPin, {is_enabled_spi_1 == 1}

	dialog = fuelClosedLoopDialog, "Fuel closed-loop correction"
		field = "Enabled",								fuelClosedLoopCorrectionEnabled
		field = "!No correction below these value"
		field = "CLT - low threshod", 					fuelClosedLoopCltThreshold, {fuelClosedLoopCorrectionEnabled == 1}
		field = "RPM - low threshod", 					fuelClosedLoopRpmThreshold, {fuelClosedLoopCorrectionEnabled == 1}
		field = "EGO - low threshod", 					fuelClosedLoopAfrLowThreshold, {fuelClosedLoopCorrectionEnabled == 1}
		field = "!No correction above these value"
		field = "TPS - high threshod", 					fuelClosedLoopTpsThreshold, {fuelClosedLoopCorrectionEnabled == 1}
		field = "EGO - high threshod", 					fuelClosedLoopAfrHighThreshold, {fuelClosedLoopCorrectionEnabled == 1}
		field = "!PID settings"
		field = "P factor",								fuelClosedLoopPid_pFactor, {fuelClosedLoopCorrectionEnabled == 1}
		field = "I factor",								fuelClosedLoopPid_iFactor, {fuelClosedLoopCorrectionEnabled == 1}
		field = "D factor",								fuelClosedLoopPid_dFactor, {fuelClosedLoopCorrectionEnabled == 1}


	dialog = auxPidDialog, "Aux PID"
		field = "Enabled",								activateAuxPid1
		field = "FSIO pin #1",							auxPidPins1
		field = "PWM Frequency",						auxPidFrequency1
		field = "verbose",								isVerboseAuxPid1
		field = "#target based on FSIO map#1"
		field = "control period",						auxPid1_period, {activateAuxPid1 == 1}
		field = "#PID control"
		field = "offset",								auxPid1_offset, {activateAuxPid1 == 1}
		field = "P factor",								auxPid1_pFactor, {activateAuxPid1 == 1}
		field = "I factor",								auxPid1_iFactor, {activateAuxPid1 == 1}
		field = "D factor",								auxPid1_dFactor, {activateAuxPid1 == 1}
		field = "Min",									auxPid1_minValue, {activateAuxPid1 == 1}
		field = "Max",									auxPid1_maxValue, {activateAuxPid1 == 1}
		field = "FSIO pin #2",							auxPidPins2
		field = "FSIO pin #3",							auxPidPins3
		field = "FSIO pin #4",							auxPidPins4

;			Engine->Battery & Alternator
	dialog = batteryDialog, "Battery Settings",	yAxis
		field = "vBatt ADC input", 						vbattAdcChannel
		field = "Battery Input Divider Coefficient",	vbattDividerCoeff
	dialog = alternator, "Alternator Settings",	yAxis
		field = "Enabled",								isAlternatorControlEnabled
		field = "simple on/off mode",					onOffAlternatorLogic, {isAlternatorControlEnabled == 1}
		field = "Target",								targetVBatt, {isAlternatorControlEnabled == 1}
		field = "Pin",									alternatorControlPin, {isAlternatorControlEnabled == 1}
		field = "Pin Mode",								alternatorControlPinMode, {isAlternatorControlEnabled == 1}
		field = "PWM frequency",						alternatorPwmFrequency, {isAlternatorControlEnabled == 1 && onOffAlternatorLogic == 0}
		field = "Off Above TPS",						alternatorOffAboveTps, {isAlternatorControlEnabled == 1}
		field = "Verbose",								isVerboseAlternator, {isAlternatorControlEnabled == 1}
		field = "control period",						alternatorControl_period, {isAlternatorControlEnabled == 1}
		field = "#PID control"
		field = "offset",								alternatorControl_offset, {isAlternatorControlEnabled == 1 && onOffAlternatorLogic == 0}
		field = "P factor",								alternatorControl_pFactor, {isAlternatorControlEnabled == 1 && onOffAlternatorLogic == 0}
		field = "I factor",								alternatorControl_iFactor, {isAlternatorControlEnabled == 1 && onOffAlternatorLogic == 0}
		field = "D factor",								alternatorControl_dFactor, {isAlternatorControlEnabled == 1 && onOffAlternatorLogic == 0}
		field = "Min",									alternatorControl_minValue, {isAlternatorControlEnabled == 1 && onOffAlternatorLogic == 0}
		field = "Max",									alternatorControl_maxValue, {isAlternatorControlEnabled == 1 && onOffAlternatorLogic == 0}
		field = "#% duty = Pterm + Iterm + Dterm + offset%"


	dialog = warmupFuelDialog, "Warmup fuel closed-loop",	yAxis
		field = "use automatic Pid Afr control",			useWarmupPidAfr
		field = "warmup temperature Threshold",				warmupAfrThreshold
		field = "wa offset",								warmupAfrPid_offset
		field = "wa P factor",								warmupAfrPid_pFactor
		field = "wa I factor",								warmupAfrPid_iFactor
		field = "wa D factor",								warmupAfrPid_dFactor
		field = "#correction = Pterm + Iterm + Dterm + offset"
		
		
	dialog = energySystems, "Battery and Alternator Settings",	yAxis
		panel = batteryDialog
		panel = alternator

;		Engine->Speed Sensor
	dialog = speedSensor,				"Speed Sensor Settings"
		field = "Input pin",							vehicleSpeedSensorInputPin
		field = "revolution to speed mult",				vehicleSpeedCoef

;			Engine->Other inputs	
	dialog = analogInputs, "Analog inputs"
		field = "!ECU reboot needed to apply these settings"
		field = "TPS ADC input", 						tpsAdcChannel
		field = "TPS low value detection threshold",	tpsErrorDetectionTooLow
		field = "TPS high value detection threshold",	tpsErrorDetectionTooHigh
		field = "!todo: move MAF channel to maf curve dialog"
		field = "MAF ADC input", 						mafAdcChannel
		field = "Baro ADC input", 						baroSensor_hwChannel
		field = "Analog divider",						analogInputDividerCoefficient
		field = "Use BiQuad averaging",					useBiQuadAnalogFiltering		
		field = "Smoothing factor",						slowAdcAlpha, {useBiQuadAnalogFiltering == 0}
		field = "Bi_Q a0",								biQuad_a0, {useBiQuadAnalogFiltering == 1}
		field = "Bi_Q a1",								biQuad_a1, {useBiQuadAnalogFiltering == 1}
		field = "Bi_Q a2",								biQuad_a2, {useBiQuadAnalogFiltering == 1}
		field = "Bi_Q b1",								biQuad_b1, {useBiQuadAnalogFiltering == 1}
		field = "Bi_Q b2",								biQuad_b2, {useBiQuadAnalogFiltering == 1}

	dialog = tachSettings, "Tachometer output"
		field = "!See also dizzySparkOutputPin"
		field = "pin",									tachOutputPin
		field = "pin mode",								tachOutputPinMode
		field = "rise at trigger index",				tachPulseTriggerIndex
		field = "pulse duration is duty cycle",			tachPulseDurationAsDutyCycle
		field = "pulse duration",						tachPulseDuractionMs


;			Board->Connection
	dialog = tsPort, "TunerStudio Port"
		field = "tunerStudioSerialSpeed",				tunerStudioSerialSpeed
		field = "Use PC10/PC11 serial?",				useSerialPort
		field = "startConsoleInBinaryMode", 			startConsoleInBinaryMode
		field = "uartConsoleSerialSpeed",				uartConsoleSerialSpeed
		
	dialog = canBus, "CAN Bus"
		field = "Can Read Enabled",						canReadEnabled
		field = "Can Write Enabled",					canWriteEnabled
;		field = "Can Nbc Type",							canNbcType
		field = "Can Sleep Period",						canSleepPeriod
		field = "TX pin",								canTxPin
		field = "RX pin",								canRxPin
	
	dialog = sdCard, "SD Card Logger"
		field = "SdCard", 								isSdCardEnabled
		field = "CS Pin",								sdCardCsPin
		field = "SPI",									sdCardSpiDevice
		field = "log format",							logFormat
		field = "Mass Storage",							storageMode
	
	dialog = gpsReceiver, "GPS Receiver"
		field = "gps RX", 								gps_rx_pin
		field = "gps TX", 								gps_tx_pin
		
	dialog = lcdScreen, "LCD screen"
		field = "display Mode",							displayMode
		field = "height", 								HD44780height
		field = "width", 								HD44780width
		field = "RS pin", 								HD44780_rs
		field = "E pin", 								HD44780_e
		field = "D4 pin", 								HD44780_db4
		field = "D5 pin", 								HD44780_db5
		field = "D6 pin", 								HD44780_db6
		field = "D7 pin", 								HD44780_db7
		
	dialog = connectRight, "", 	yAxis
		panel = tsPort
		panel = canBus
		panel = sdCard
		panel = gpsReceiver
		field = "stm32 voltage",						adcVcc
	
	dialog = connection, "", 	border
		panel = lcdScreen,		East
		panel = connectRight,	West

	dialog = joystickPanel, "Joystick"
		field = "joustick center button",				joystickCenterPin
		field = "joustick button A",					joystickAPin
		field = "joustick button B",					joystickBPin
		field = "joustick button C",					joystickCPin
		field = "joustick button D",					joystickDPin
				
	dialog = monitoringSettings, "rusEfi Console Settings"			
		field = "Sensor Sniffer",         	    		sensorChartMode
		field = "  Threshold",							sensorSnifferRpmThreshold
		field = "  Each X cycle",						sensorChartFrequency
		field = "Engine Sniffer", 						isEngineChartEnabled			
		field = "  Threshold", 							engineSnifferRpmThreshold
		
				
				
;			Tuning->General
	dialog = generalSettings, "General"
		field = "http://rusefi.com/support"
		field = "RPM Hard Limit",         	    		rpmHardLimit
		field = "Boost Cut Pressure",					boostCutPressure
		field = ""
		field = "http://rusefi.com/fuel"
		field = "Fuel Algorithm",						fuelAlgorithm
		field = ""
		field = "#System hack's"
		field = "Global fuel correction", 				globalFuelCorrection
		field = "Ignition Math Logic @",				ignMathCalculateAtIndex
		field = "MAP Averaging Logic @",				mapAveragingSchedulingAtIndex
		field = "comm status pin",						communicationPin
		field = "running status",						runningPin
		
	dialog = crankingFuel, "Fuel"
		field = "Injection Mode",						crankingInjectionMode
		field = "Base Fuel Pulse Width", 				cranking_baseFuel
		
		
	dialog = crankingIgnition, "Ignition"
		field = "Advance", 								crankingTimingAngle
        field = "Use fixed Dwell?",         			useConstantDwellDuringCranking
        field = "Fixed Dwell",           			ignitionDwellForCrankingMs, {useConstantDwellDuringCranking == 1}
		field = "Charge Angle", 						crankingChargeAngle, {useConstantDwellDuringCranking == 0}
	
		dialog = postCrankingEnrichment, "Post-cranking short-time fuel enrichment"
		field = "Target temperature", 			postCrankingTargetClt
		field = "Post-Cranking factor", 				postCrankingFactor
		field = "Duraction", 				postCrankingDurationSec
		
		
;			Tuning->Cranking
	dialog = crankingDialog, "Cranking"				
		field = "Cranking RPM limit",                	cranking_rpm
		panel = crankingFuel
		panel = crankingIgnition
		field = "Cranking Idle Air",					crankingIACposition
		field = "Priming fuel pulse",					startOfCrankingPrimingPulse
		panel = postCrankingEnrichment
		field = ""
		field = ""
		field = "enable Cylinder Cleanup",				isCylinderCleanupEnabled
		field = "Startup fuel prime duration",			startUpFuelPumpDuration
		field = "After cranking IAC taper duration",	afterCrankingIACtaperDuration
		
		
	dialog = EngineLoadAccelPanel, "Engine Load (alpha version)"
		field = "Length",						engineLoadAccelLength
		field = "Accel Threshold", 				engineLoadAccelEnrichmentThreshold
		field = "Accel Multiplier",	 			engineLoadAccelEnrichmentMultiplier
		field = "Decel Threshold", 				engineLoadDecelEnleanmentThreshold
		field = "Decel Multiplier",	 			engineLoadDecelEnleanmentMultiplier

	dialog = TpsAccelPanel, "TPS"
   		field = "Length",						tpsAccelLength
		field = "Accel Threshold", 				tpsAccelEnrichmentThreshold
		field = "Decel Threshold", 				tpsDecelEnleanmentThreshold
;		field = "Decel Multiplier",	 			tpsDecelEnleanmentMultiplier
		
	dialog = WallWettingAccelPanel, "Wall Wetting (alpha version)"
		field = "sucked off wall coefficient",          suckedOffCoef
		field = "added to wall coef",                   addedToWallCoef
	
		
;			Tuning->AccelEnrichment
	dialog = AccelEnrich,	"Accel/Decel Enrichment"
		panel = TpsAccelPanel
		panel = WallWettingAccelPanel
		panel = EngineLoadAccelPanel
		field = "No accel after RPM hard limit",		noAccelAfterHardLimitPeriodSecs
		
		
;			Flex Logic
	dialog = fsioIO, "Outputs"
		field = "output #1", 							fsioOutputPins1
		field = "output #2", 							fsioOutputPins2
		field = "output #3", 							fsioOutputPins3
		field = "output #4", 							fsioOutputPins4
		field = "output #5", 							fsioOutputPins5
		field = "output #6", 							fsioOutputPins6
		field = "output #7", 							fsioOutputPins7
		field = "output #8", 							fsioOutputPins8
		field = "output #9", 							fsioOutputPins9
		field = "output #10", 							fsioOutputPins10
		field = "output #11", 							fsioOutputPins11
		field = "output #12", 							fsioOutputPins12
		field = "output #13", 							fsioOutputPins13
		field = "output #14", 							fsioOutputPins14
		field = "output #15", 							fsioOutputPins15
		field = "output #16", 							fsioOutputPins16
		field = "aux valve #1", 						auxValves1
		field = "aux valve #2", 						auxValves2
		field = ""
		field = ""
		
	dialog = fsioFrequency, "Frequency"
		field = "freq #1", 								fsioFrequency1
		field = "freq #2", 								fsioFrequency2
		field = "freq #3", 								fsioFrequency3
		field = "freq #4", 								fsioFrequency4
		field = "freq #5", 								fsioFrequency5
		field = "freq #6", 								fsioFrequency6
		field = "freq #7", 								fsioFrequency7
		field = "freq #8", 								fsioFrequency8
		field = "freq #9", 								fsioFrequency9
		field = "freq #10", 							fsioFrequency10
		field = "freq #11", 							fsioFrequency11
		field = "freq #12", 							fsioFrequency12
		field = "freq #13", 							fsioFrequency13
		field = "freq #14", 							fsioFrequency14
		field = "freq #15", 							fsioFrequency15
		field = "freq #16", 							fsioFrequency16
		field = ""
		field = ""
	
	dialog = fsioSetting, "Setting"
		field = "Set number is not associated with the output number."
		field = "Set number, only the cell number with some numbers."
		field = "set #1",								fsio_setting1
		field = "set #2",								fsio_setting2
		field = "set #3",								fsio_setting3
		field = "set #4",								fsio_setting4
		field = "set #5",								fsio_setting5
		field = "set #6",								fsio_setting6
		field = "set #7",								fsio_setting7
		field = "set #8",								fsio_setting8
		field = "set #9",								fsio_setting9
		field = "set #10",								fsio_setting10
		field = "set #11",								fsio_setting11
		field = "set #12",								fsio_setting12
		field = "set #13",								fsio_setting13
		field = "set #14",								fsio_setting14
		field = "set #15",								fsio_setting15
		field = "set #16",								fsio_setting16
		
	dialog = fsioOutputsDialog, "FSIO outputs", border
		panel = fsioIO,			West
		panel = fsioFrequency,	Center
		panel = fsioSetting,	East
		
	dialog = fsioFormulas, "FSIO Formulas"
		field = "#1",									fsioFormulas1
		field = "#2",									fsioFormulas2
		field = "#3",									fsioFormulas3
		field = "#4",									fsioFormulas4
		field = "#5",									fsioFormulas5
		field = "#6",									fsioFormulas6
		field = "#7",									fsioFormulas7
		field = "#8",									fsioFormulas8
		field = "#9",									fsioFormulas9
		field = "#10",									fsioFormulas10
		field = "#11",									fsioFormulas11
		field = "#12",									fsioFormulas12
		field = "#13",									fsioFormulas13
		field = "#14",									fsioFormulas14
		field = "#15",									fsioFormulas15
		field = "use FSIO #16 for timing adjustment",	useFSIO16ForTimingAdjustment
		field = "#16",									fsioFormulas16
		
	dialog = fsioInputsDialog, "FSIO inputs"
		field = "ADC #1",								fsioAdc1
		field = "ADC #2",								fsioAdc2
		field = "ADC #3",								fsioAdc3
		field = "ADC #4",								fsioAdc4
				
	dialog = veTableDialogNorth
		field = "Volumetric Efficiency is used to calculate fuel in Speed Density mode"
		field = "http://rusefi.com/fuel"
				
	dialog = veTableDialog, "VE Table"
		panel = veTableDialogNorth, North
		panel = veTableTbl, South
				
	dialog = veTableDialog3D, "VE Table"
		panel = veTableDialogNorth, North
		panel = veTableMap, South
				
	dialog = etbDialog, "Electronic Thtottle Body (alpha)"			
		field = "pedal Position Channel", 				pedalPositionChannel
		field = "verbose",								isVerboseETB
		field = "Throttle Pedal Up",					throttlePedalUpVoltage
		field = "Throttle Pedal Wide Open",				throttlePedalWOTVoltage
		field = "PWM Frequency",						etbFreq, {pedalPositionChannel != 16}
		field = "Dir #1",								etbDirectionPin1, {pedalPositionChannel != 16}
		field = "Dir #2",								etbDirectionPin2, {pedalPositionChannel != 16}
		field = "Control #1",							etbControlPin1, {pedalPositionChannel != 16}
		field = "Control #2",							etbControlPin2, {pedalPositionChannel != 16}
		field = "pFactor",								etb_pFactor, {pedalPositionChannel != 16}
		field = "iFactor",								etb_iFactor, {pedalPositionChannel != 16}
		field = "dFactor",								etb_dFactor, {pedalPositionChannel != 16}	
		field = "offset",								etb_offset, {pedalPositionChannel != 16}
		field = "control period",						etb_period, {pedalPositionChannel != 16}
		field = "pid min",								etb_minValue, {pedalPositionChannel != 16}	
		field = "pid max",								etb_maxValue, {pedalPositionChannel != 16}	
				
	dialog = testSpark, "Spark"
		commandButton = "Spark #1", cmd_test_spk1
		commandButton = "Spark #2", cmd_test_spk2
		commandButton = "Spark #3", cmd_test_spk3
		commandButton = "Spark #4", cmd_test_spk4
		commandButton = "Spark #5", cmd_test_spk5
		commandButton = "Spark #6", cmd_test_spk6
		commandButton = "Spark #7", cmd_test_spk7
		commandButton = "Spark #8", cmd_test_spk8
		
	dialog = testInjectors, "Fuel"
		commandButton = "Injector #1", cmd_test_inj1
		commandButton = "Injector #2", cmd_test_inj2
		commandButton = "Injector #3", cmd_test_inj3
		commandButton = "Injector #4", cmd_test_inj4
		commandButton = "Injector #5", cmd_test_inj5
		commandButton = "Injector #6", cmd_test_inj6
		commandButton = "Injector #7", cmd_test_inj7
		commandButton = "Injector #8", cmd_test_inj8
		
	dialog = testMisc, "Misc"
		commandButton = "Come To Pit", cmd_call_from_pit
		commandButton = "Fuel Pump", cmd_test_fuel_pump
		commandButton = "Radiator Fan", cmd_test_radiator_fan
		commandButton = "Check Engine", cmd_test_check_engine_light
		commandButton = "Idle Air Valve", cmd_test_idle_valve          
		commandButton = "Stop Engine", cmd_stop_engine          
		
	; bench test	
	dialog = ioTest, "I-O Test", border
		panel = testSpark,		West
		panel = testInjectors,	Center
		panel = testMisc,		East


;			Board->ECU stimulator
	dialog = ecuStimulator, "ECU stimulator"
		field = "Trigger Simulator",   					triggerSimulatorFrequency
		field = "self-stimulation",						directSelfStimulation
		field = ""
		field = "digipot spi", 							digitalPotentiometerSpiDevice
		field = "digipot CS #0", 						digitalPotentiometerChipSelect1
		field = "digipot CS #1", 						digitalPotentiometerChipSelect2
		field = "digipot CS #2", 						digitalPotentiometerChipSelect3
		field = "digipot CS #3", 						digitalPotentiometerChipSelect4
		field = ""
		field = "trigger stimulator pin #1", 			triggerSimulatorPins1
		field = "trigger stimulator pin #2", 			triggerSimulatorPins2
		field = "trigger stimulator pin #3", 			triggerSimulatorPins3
		field = ""
	    field = "Logic input channel 1", 				logicAnalyzerPins1
	    field = "Logic input channel 2", 				logicAnalyzerPins2
	    field = "Logic input channel 3", 				logicAnalyzerPins3
	    field = "Logic input channel 4", 				logicAnalyzerPins4
		field = ""
	    field = "Engine chart size", 					engineChartSize

				;			Racing Features->Launch Control
	dialog = smLaunchControl, "Launch Control Settings"
		field = "RPM Step1 Limit",         	    		step1rpm
		field = "Launch RPM Window"                     step1RpmWindow
		field = "Step1 Ignition Advance",				step1timing
		field = "Use Spark Cut",						step1SparkCutEnable
		field = "Use Fuel Cut",							step1fuelCutEnable
		field = "clutchDownPin",						clutchDownPin
		field = "clutchUpPin",							clutchUpPin
		field = "brakePedalPin",						brakePedalPin
	    
[Tools]
 ;addTool = toolName, PanelName
 addTool = veTableGenerator, "VE Table Generator", veTableTbl
 addTool = afrTableGenerator, "AFR Table Generator", afrTableTbl