ini06 Remove redundant ADC inputs & Add a few gauges (#579)

* Remove redundant ADC inputs & Add a few gauges

* Rearrange VE table help

* Fix typo

* Change color from red ('Warning') to blue('Note')

firmware/tunerstudio/rusefi.input

@@ -1198,7 +1198,7 @@ cmd_stop_engine              = "w\x00\x99\x00\x00"
 		panel = injectorSetting,		West
 		panel = injectorsDeadTime,		East
 
-	dialog = ignitionCylExtra, "Ignition Cyliner Extra"
+	dialog = ignitionCylExtra, "Ignition Cylinder Extra"
 		field = "Extra cyl #1",                       timing_offset_cylinder1
 		field = "Extra cyl #2",                       timing_offset_cylinder2, {cylindersCount > 1}
 		field = "Extra cyl #3",                       timing_offset_cylinder3, {cylindersCount > 2}
@@ -1238,7 +1238,7 @@ cmd_stop_engine              = "w\x00\x99\x00\x00"
 		panel = ignitionCylExtra,	East
 		
 ;			Engine->Aux1 Thermistor Settings
-	dialog = auxTempSensor1_thermistor, "aux1 Thermistor Settings"
+	dialog = auxTempSensor1Sensor,	"aux1 Thermistor Settings"
 		field = "!Here is three pairs of thermistor temperature and his resistance."
 		field = "!Typical temperatures is -40°C, 0°C and 100°C"
 		field = ""
@@ -1250,15 +1250,9 @@ cmd_stop_engine              = "w\x00\x99\x00\x00"
 		field = ""
 		field = "Highest temperature",				 	auxTempSensor1_tempC_3
 		field = "Resistance @ HT",         	    		auxTempSensor1_resistance_3
-	dialog = auxTempSensor1Sensor_IO,	"auxTempSensor1 Sensor I/O"
-		field = "auxTempSensor1 ADC input",				auxTempSensor1_adcChannel
-		field = "Bias Resistor Value",    	    		auxTempSensor1_bias_resistor
-	dialog = auxTempSensor1Sensor, "", yAxis
-		panel = auxTempSensor1_thermistor,		North
-		panel = auxTempSensor1Sensor_IO,		South
 
 ;			Engine->Aux2 Thermistor Settings
-	dialog = auxTempSensor2_thermistor, "aux1 Thermistor Settings"
+	dialog = auxTempSensor2Sensor, "aux2 Thermistor Settings"
 		field = "!Here is three pairs of thermistor temperature and his resistance."
 		field = "!Typical temperatures is -40°C, 0°C and 100°C"
 		field = ""
@@ -1270,12 +1264,6 @@ cmd_stop_engine              = "w\x00\x99\x00\x00"
 		field = ""
 		field = "Highest temperature",				 	auxTempSensor2_tempC_3
 		field = "Resistance @ HT",         	    		auxTempSensor2_resistance_3
-	dialog = auxTempSensor2Sensor_IO,	"auxTempSensor2 Sensor I/O"
-		field = "auxTempSensor2 ADC input",				auxTempSensor2_adcChannel
-		field = "Bias Resistor Value",    	    		auxTempSensor2_bias_resistor
-	dialog = auxTempSensor2Sensor, "", yAxis
-		panel = auxTempSensor2_thermistor,		North
-		panel = auxTempSensor2Sensor_IO,		South
 		
 ;			Sensor Inputs
 	dialog = otherSensorInputs,					"Other Sensor Inputs"		
@@ -1439,11 +1427,10 @@ cmd_stop_engine              = "w\x00\x99\x00\x00"
 		panel = allPins1_2
 		panel = allPins3_4
 
-
-;			Engine->CLT Thermistor Settings
-	dialog = clt_thermistor, "CLT Thermistor Settings"
-		field = "!Here is three pairs of thermistor temperature and his resistance."
-		field = "!Typical temperatures is -40°C, 0°C and 100°C"
+;			Sensors->CLT Sensor Settings
+	dialog = clt_thermistor, "CLT Sensor Settings"
+		field = "#Here is three pairs of thermistor temperature and his resistance."
+		field = "#Typical temperatures is -40°C, 0°C and 100°C"
 		field = ""
 		field = "Lowest temperature",  					clt_tempC_1		
 		field = "Resistance @ LT",         	   			clt_resistance_1
@@ -1453,18 +1440,17 @@ cmd_stop_engine              = "w\x00\x99\x00\x00"
 		field = ""
 		field = "Highest temperature",				 	clt_tempC_3
 		field = "Resistance @ HT",         	    		clt_resistance_3
-		field = "Is linear?",							useLinearCltSensor
-	dialog = cltSensor_IO,	"CLT Sensor I/O"
-		field = "CLT ADC input", 						clt_adcChannel
-		field = "Bias Resistor Value",    	    		clt_bias_resistor
-	dialog = cltSensor, "", yAxis
-		panel = clt_thermistor,		North
-		panel = cltSensor_IO,		South
+		field = ""
+		field = "Linear characteristic",				useLinearCltSensor
 
-;			Engine->IAT Thermistor Settings
-	dialog = iat_thermistor, "IAT Thermistor Settings"
-		field = "!Here is three pairs of thermistor temperature and his resistance."
-		field = "!Typical temperatures is -40°C, 0°C and 100°C"
+	dialog = cltSensor, "", xAxis
+		panel = clt_thermistor
+		gauge = CLTGauge
+
+;			Sensors->IAT Sensor Settings
+	dialog = iat_thermistor, "IAT Sensor Settings"
+		field = "#Here is three pairs of thermistor temperature and his resistance."
+		field = "#Typical temperatures is -40°C, 0°C and 100°C"
 		field = ""
 		field = "Lowest temperature",                   iat_tempC_1		
 		field = "Resistance @ LT",         	   			iat_resistance_1
@@ -1474,24 +1460,18 @@ cmd_stop_engine              = "w\x00\x99\x00\x00"
 		field = ""
 		field = "Highest temperature",         	    	iat_tempC_3
 		field = "Resistance @ HT",         	    		iat_resistance_3
-	dialog = iatSensor_IO,	"IAT Sensor I/O"
-		field = "IAT ADC input", 						iat_adcChannel
-		field = "Bias Resistor Value",    	    		iat_bias_resistor
-		field = "Is linear?",							useLinearIatSensor
-	dialog = iatSensor, "", yAxis
-		panel = iat_thermistor,		North
-		panel = iatSensor_IO,		South
+		field = ""
+		field = "Linear characteristic",				useLinearIatSensor
 
+	dialog = iatSensor, "", xAxis
+		panel = iat_thermistor
+		gauge = IATGauge
+		
 	dialog = oilp_settings, "Oil Pressure Sensor Settings"
 		field = "low voltage",							oilPressure_v1
 		field = "low pressure",							oilPressure_value1
 		field = "high voltage",							oilPressure_v2
 		field = "high pressure",						oilPressure_value2
-	dialog = oilp_IO, "Oil Pressure Sensor I/O"
-		field = "Oil Pressure ADC input",				oilPressure_hwChannel
-	dialog = oilPressureSensor, "", yAxis
-		panel = oilp_settings, North
-		panel = oilp_IO, South
 
 ;			Engine->MAP Sensor Settings
 	dialog = mapSensorVDlg, "Voltage Sensor Settings", xAxis		
@@ -1749,21 +1729,17 @@ cmd_stop_engine              = "w\x00\x99\x00\x00"
 		panel = batteryDialog
 		panel = alternator
 
-;		Engine->Speed Sensor
-	dialog = speedSensor,				"Speed Sensor Settings"
-		field = "Input pin",							vehicleSpeedSensorInputPin
+;			Sensors->Vehicle Speed Sensor Setting
+	dialog = speedSensor, "Speed Sensor Settings", xAxis
 		field = "revolution to speed mult",				vehicleSpeedCoef
+		gauge = VSSGauge
 
 ;			Engine->Other inputs	
 	dialog = analogInputSettings, "Analog Input Settings"
 		field = "!ECU reboot needed to apply these settings"
-		field = "TPS ADC input", 						tpsAdcChannel
 		field = "TPS low value detection threshold",	tpsErrorDetectionTooLow
 		field = "TPS high value detection threshold",	tpsErrorDetectionTooHigh
 		field = "!todo: move MAF channel to maf curve dialog"
-		field = "MAF ADC input", 						mafAdcChannel
-		field = "Baro ADC input", 						baroSensor_hwChannel
-		field = "Flex Fuel",							flexFuelSensor
 		field = "Use fixed baro corr from MAP", 		useFixedBaroCorrFromMap
 		field = "Analog divider",						analogInputDividerCoefficient
 		field = "Use BiQuad averaging",					useBiQuadAnalogFiltering		
@@ -2027,20 +2003,19 @@ cmd_stop_engine              = "w\x00\x99\x00\x00"
 		field = "ADC #3",								fsioAdc3
 		field = "ADC #4",								fsioAdc4
 				
-	dialog = veTableDialogNorth
-		field = "Volumetric Efficiency is used to calculate fuel in Speed Density mode"
-		field = "http://rusefi.com/fuel"
+	help = veTableDialogHelp, "Volumetric Efficiency"
+        text = "Volumetric Efficiency is used to calculate fuel in Speed Density mode"
+        webHelp = "http://rusefi.com/fuel"
 				
-	dialog = veTableDialog, "VE Table"
-		panel = veTableDialogNorth, North
+	dialog = veTableDialog
+		topicHelp = "veTableDialogHelp"
 		panel = veTableTbl, South
 				
 	dialog = veTableDialog3D, "VE Table"
-		panel = veTableDialogNorth, North
+		topicHelp = "veTableDialogHelp"
 		panel = veTableMap, South
 				
 	dialog = etbDialog, "Electronic Thtottle Body (alpha)"			
-		field = "pedal Position Channel", 				pedalPositionChannel
 		field = "verbose",								isVerboseETB
 		field = "Throttle Pedal Up",					throttlePedalUpVoltage
 		field = "Throttle Pedal Wide Open",				throttlePedalWOTVoltage