rusefi
/
rusefi
mirror of https://github.com/rusefi/rusefi.git
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity

status LED UI is dead!

This commit is contained in:
Matthew Kennedy 2023-06-05 03:13:45 -04:00 committed by rusefillc
parent 56e9c9b911
commit bacbb99ff0
2 changed files with 2 additions and 18 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

8
firmware/integration/rusefi_config.txt
View File

@ -494,7 +494,6 @@ float cylinderBore;Cylinder diameter in mm.;"mm", 1, 0, 0, 20000, 2
custom engine_load_mode_e 1 bits, U08, @OFFSET@, [0:2], @@engine_load_mode_e_enum@@
engine_load_mode_e fuelAlgorithm;This setting controls which fuel quantity control algorithm is used.\nAlpha-N means drive by TPS commonly only used for NA engines\nSpeed Density requires MAP sensor and is the default choice for may installs\nMAF air charge is a cylinder filling based method that uses a mass air flow sensor.;
uint8_t ALSMaxTPS;;"%", 1, 0, 0, 10, 0
Gpio criticalLedPin;
custom injection_mode_e 1 bits, U08, @OFFSET@, [0:1], "Simultaneous", "Sequential", "Batch", "Single Point"
injection_mode_e crankingInjectionMode;This is the injection strategy during engine start. See Fuel/Injection settings for more detail. It is suggested to use "Simultaneous".
@ -1091,8 +1090,6 @@ int16_t tps2Max;Full throttle#2. tpsMax value as 10 bit ADC value. Not Voltage!\
pid_s idleRpmPid;See cltIdleRpmBins
float wwaeBeta;0 = No fuel settling on port walls 1 = All the fuel settling on port walls setting this to 0 disables the wall wetting enrichment. ;"Fraction", 1, 0, 0, 1, 2
Gpio communicationLedPin;blue LED on many rusEFI boards.\nBlue Communication LED which is expected to blink at 50% duty cycle during normal board operation.\nIf USB communication cable is connected Blue LED starts to blink faster.
Gpio runningLedPin;Green LED on many rusEFI boards.\nOff if engine is stopped, blinks if engine is cranking, solid if engine is running.
Gpio binarySerialTxPin;See also EFI_CONSOLE_RX_BRAIN_PIN
Gpio binarySerialRxPin;
@ -1113,9 +1110,8 @@ int16_t tps2Max;Full throttle#2. tpsMax value as 10 bit ADC value. Not Voltage!\
int16_t iacByTpsTaper;Extra IAC, in percent between 0 and 100, tapered between zero and idle deactivation TPS value;"percent", 1, 0, 0, 500, 0
Gpio auxSerialTxPin;Auxiliary sensor serial, not to be confused with secondary calibration serial\nset_aux_tx_pin X;
Gpio warningLedPin;
Gpio auxSerialRxPin;Auxiliary sensor serial, not to be confused with secondary calibration serial\nset_aux_rx_pin X;
Gpio auxSerialTxPin;Auxiliary sensor serial, not to be confused with secondary calibration serial;
Gpio auxSerialRxPin;Auxiliary sensor serial, not to be confused with secondary calibration serial;
Gpio LIS302DLCsPin;

12
firmware/tunerstudio/rusefi.input
View File

@ -272,8 +272,6 @@ enable2ndByteCanID = false
requiresPowerCycle = boardUseCanTerminator
requiresPowerCycle = lps25BaroSensorScl
requiresPowerCycle = lps25BaroSensorSda
requiresPowerCycle = warningLedPin
requiresPowerCycle = runningLedPin
requiresPowerCycle = binarySerialTxPin
requiresPowerCycle = binarySerialRxPin
requiresPowerCycle = tunerStudioSerialSpeed
@ -2831,8 +2829,6 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
dialog = allPins1_1
field = "trigger stimulator output #1", triggerSimulatorPins1
field = "trigger stimulator output #2", triggerSimulatorPins2
field = "Critical Led", criticalLedPin @@if_ts_show_critical_led
field = "Warning Led", warningLedPin
field = "tle6240_cs", tle6240_cs
field = "tle6240 SPI", tle6240spiDevice
@ -2924,9 +2920,6 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
field = "DRV8860 CS Mode", drv8860_csPinMode
field = "DRV8860 MISO pin", drv8860_miso
field = "DRV8860 SPI", drv8860spiDevice
field = "comm status light", communicationLedPin
field = "running status light", runningLedPin
dialog = allPins3_1
panel = allPinsSensors
@ -3414,14 +3407,9 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
panel = fanSetting, Center
dialog = statusLeds, "Status LEDs"
field = "Critical Led", criticalLedPin @@if_ts_show_critical_led
field = "Running status LED", runningLedPin
field = "TS communication status LED", communicationLedPin
field = "Warning LED", warningLedPin
field = "Trigger error LED", triggerErrorPin
field = "Debug Trigger Sync", debugTriggerSync
dialog = softwareKnockCfg, "Sense"
field = "Enable", enableSoftwareKnock
field = "Cylinder Bore", cylinderBore