mirror of https://github.com/rusefi/rusefi.git
TS: UI: rename Pin to input or output where possible (#4725)
Keep Pin term only for internal connections (SD, SPI...)
This commit is contained in:
Andrey G
GitHub
parent
0609f97aa5
commit
dfab126c92
|
|
@ -2098,8 +2098,8 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
field = "Injection phase control mode", injectionTimingMode, { isInjectionEnabled }
|
||||
|
||||
dialog = ignitionOutputs, "Ignition Outputs"
|
||||
field = "Ignition Pin Mode", ignitionPinMode, {isIgnitionEnabled == 1}@@if_ts_show_ignitionPinMode
|
||||
field = "Ignition Pin 1", ignitionPins1, {isIgnitionEnabled == 1}
|
||||
field = "Ignition Output Mode", ignitionPinMode, {isIgnitionEnabled == 1}@@if_ts_show_ignitionPinMode
|
||||
field = "Ignition Output 1", ignitionPins1, {isIgnitionEnabled == 1}
|
||||
; see rusefi_config.txt comment next to 'ignitionPin2logic' which says
|
||||
; this section is auto-generated by FiringOrderTSLogic.java
|
||||
@@FIRINGORDER@@
|
||||
|
|
@ -2228,21 +2228,21 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
field = "E100 stoichiometric ratio", stoichRatioSecondary, {isInjectionEnabled == 1 && flexSensorPin != 0 }
|
||||
|
||||
dialog = injectorOutputSettings, "Injector Outputs", yAxis
|
||||
field = "Use only first half of pins for batch mode"
|
||||
field = "Injection Pin 1", injectionPins1, {isInjectionEnabled == 1}
|
||||
field = "Injection Pin 2", injectionPins2, {isInjectionEnabled == 1 && injectionMode != 3 && cylindersCount > 1}
|
||||
field = "Injection Pin 3", injectionPins3, {isInjectionEnabled == 1 && injectionMode != @@injection_mode_e_IM_SINGLE_POINT@@ && cylindersCount > 2}
|
||||
field = "Injection Pin 4", injectionPins4, {isInjectionEnabled == 1 && injectionMode != 3 && cylindersCount > 3}
|
||||
field = "Injection Pin 5 ", injectionPins5, {isInjectionEnabled == 1 && injectionMode != @@injection_mode_e_IM_SINGLE_POINT@@ && cylindersCount > 4}
|
||||
field = "Injection Pin 6 ", injectionPins6, {isInjectionEnabled == 1 && injectionMode != @@injection_mode_e_IM_SINGLE_POINT@@ && cylindersCount > 5}
|
||||
field = "Injection Pin 7 ", injectionPins7, {isInjectionEnabled == 1 && injectionMode != 3 && cylindersCount > 6}
|
||||
field = "Injection Pin 8 ", injectionPins8, {isInjectionEnabled == 1 && injectionMode != 3 && cylindersCount > 7}
|
||||
field = "Injection Pin 9 ", injectionPins9, {isInjectionEnabled == 1 && cylindersCount > 8}
|
||||
field = "Injection Pin 10 ", injectionPins10, {isInjectionEnabled == 1 && cylindersCount > 9}
|
||||
field = "Injection Pin 11 ", injectionPins11, {isInjectionEnabled == 1 && cylindersCount > 10}
|
||||
field = "Injection Pin 12 ", injectionPins12, {isInjectionEnabled == 1 && cylindersCount > 11}
|
||||
field = "Use only first half of outputs for batch mode"
|
||||
field = "Injection Output 1", injectionPins1, {isInjectionEnabled == 1}
|
||||
field = "Injection Output 2", injectionPins2, {isInjectionEnabled == 1 && injectionMode != 3 && cylindersCount > 1}
|
||||
field = "Injection Output 3", injectionPins3, {isInjectionEnabled == 1 && injectionMode != @@injection_mode_e_IM_SINGLE_POINT@@ && cylindersCount > 2}
|
||||
field = "Injection Output 4", injectionPins4, {isInjectionEnabled == 1 && injectionMode != 3 && cylindersCount > 3}
|
||||
field = "Injection Output 5 ", injectionPins5, {isInjectionEnabled == 1 && injectionMode != @@injection_mode_e_IM_SINGLE_POINT@@ && cylindersCount > 4}
|
||||
field = "Injection Output 6 ", injectionPins6, {isInjectionEnabled == 1 && injectionMode != @@injection_mode_e_IM_SINGLE_POINT@@ && cylindersCount > 5}
|
||||
field = "Injection Output 7 ", injectionPins7, {isInjectionEnabled == 1 && injectionMode != 3 && cylindersCount > 6}
|
||||
field = "Injection Output 8 ", injectionPins8, {isInjectionEnabled == 1 && injectionMode != 3 && cylindersCount > 7}
|
||||
field = "Injection Output 9 ", injectionPins9, {isInjectionEnabled == 1 && cylindersCount > 8}
|
||||
field = "Injection Output 10 ", injectionPins10, {isInjectionEnabled == 1 && cylindersCount > 9}
|
||||
field = "Injection Output 11 ", injectionPins11, {isInjectionEnabled == 1 && cylindersCount > 10}
|
||||
field = "Injection Output 12 ", injectionPins12, {isInjectionEnabled == 1 && cylindersCount > 11}
|
||||
field = ""@@if_ts_show_injectionPinMode
|
||||
field = "injection Pin Mode", injectionPinMode, {isInjectionEnabled == 1}@@if_ts_show_injectionPinMode
|
||||
field = "injection Output(s) Mode", injectionPinMode, {isInjectionEnabled == 1}@@if_ts_show_injectionPinMode
|
||||
|
||||
dialog = cylinderBankSelect, "Cylinder Banks", yAxis
|
||||
field = "Cylinder 1", cylinderBankSelect1, {isInjectionEnabled == 1}
|
||||
|
|
@ -2498,12 +2498,12 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
panel = tpsGauges, East
|
||||
|
||||
dialog = wastegatePosConfig, "Wastegate position sensor"
|
||||
field = "Input pin", wastegatePositionSensor
|
||||
field = "Input", wastegatePositionSensor
|
||||
field = "Min (fully closed, most boost)", wastegatePositionMin
|
||||
field = "Max (fully open, least boost)", wastegatePositionMax
|
||||
|
||||
dialog = idlePosConfig, "Idle position sensor"
|
||||
field = "Input pin", idlePositionSensor
|
||||
field = "Input", idlePositionSensor
|
||||
field = "Min (valve closed, low idle)", idlePositionMin
|
||||
field = "Max (valve open, high idle)", idlePositionMax
|
||||
|
||||
|
|
@ -2595,11 +2595,11 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
field = "AFR ADC input", afr_hwChannel
|
||||
field = "Baro ADC input", baroSensor_hwChannel
|
||||
field = "MAP ADC input", map_sensor_hwChannel
|
||||
field = "FuelLevelSensor", fuelLevelSensor
|
||||
field = "Vehicle Speed Input pin", vehicleSpeedSensorInputPin
|
||||
field = "clutchDownPin", clutchDownPin
|
||||
field = "clutchUpPin", clutchUpPin
|
||||
field = "brakePedalPin", brakePedalPin
|
||||
field = "Fuel Level input", fuelLevelSensor
|
||||
field = "Vehicle Speed input", vehicleSpeedSensorInputPin
|
||||
field = "Clutch Down input", clutchDownPin
|
||||
field = "Clutch Up input", clutchUpPin
|
||||
field = "Brake pedal input", brakePedalPin
|
||||
field = "A/C Switch", acSwitch
|
||||
field = "Aux Temperature #1", auxTempSensor1_adcChannel
|
||||
field = "Aux Temperature #2", auxTempSensor2_adcChannel
|
||||
|
|
@ -2622,22 +2622,22 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
field = hpfpValcePin, hpfpValvePin
|
||||
|
||||
dialog = allPins1_1
|
||||
field = "trigger stimulator pin #1", triggerSimulatorPins1
|
||||
field = "trigger stimulator pin #2", triggerSimulatorPins2
|
||||
field = "trigger stimulator output #1", triggerSimulatorPins1
|
||||
field = "trigger stimulator output #2", triggerSimulatorPins2
|
||||
field = "Warning Led", warningLedPin
|
||||
field = "tle6240_cs", tle6240_cs
|
||||
field = "tle6240 SPI", tle6240spiDevice
|
||||
panel = joystickPanel
|
||||
|
||||
dialog = allPins1_2
|
||||
field = "Tachometer output Pin", tachOutputPin
|
||||
field = "O2 heater pin", o2heaterPin
|
||||
field = "Idle Solenoid Pin", idle_solenoidPin
|
||||
field = "Second Idle Solenoid Pin", secondSolenoidPin
|
||||
field = "Tachometer output", tachOutputPin
|
||||
field = "O2 heater output", o2heaterPin
|
||||
field = "Idle Solenoid Primary output", idle_solenoidPin
|
||||
field = "Idle Solenoid Secondary output",secondSolenoidPin
|
||||
field = "Idle Stepper Dir", idle_stepperDirectionPin
|
||||
field = "Idle Stepper Step", idle_stepperStepPin
|
||||
field = "Idle Stepper Enable", stepperEnablePin
|
||||
field = "Fuel Pump Pin", fuelPumpPin
|
||||
field = "Fuel Pump output", fuelPumpPin
|
||||
field = "ETB#1 Dir #1", etbIo1_directionPin1 @@if_ts_show_etb_pins
|
||||
field = "ETB#1 Dir #2", etbIo1_directionPin2 @@if_ts_show_etb_pins
|
||||
field = "ETB#1 Control", etbIo1_controlPin @@if_ts_show_etb_pins
|
||||
|
|
@ -2647,7 +2647,7 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
field = "ETB#2 Control", etbIo2_controlPin @@if_ts_show_etb_pins
|
||||
field = "ETB#2 Disable", etbIo2_disablePin @@if_ts_show_etb_pins
|
||||
field = "SD CS Pin", sdCardCsPin @@if_ts_show_sd_card
|
||||
field = "MIL / Check Engine Pin", malfunctionIndicatorPin
|
||||
field = "MIL/Check Engine output", malfunctionIndicatorPin
|
||||
field = "test557pin", test557pin
|
||||
field = "Fan Pin", fanPin
|
||||
field = "A/C Relay", acRelayPin
|
||||
|
|
@ -2655,35 +2655,35 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
field = "Starter Relay Pin", starterRelayDisablePin
|
||||
|
||||
dialog = allPins2_1
|
||||
field = "Injection Pin 1", injectionPins1
|
||||
field = "Injection Pin 2", injectionPins2
|
||||
field = "Injection Pin 3", injectionPins3
|
||||
field = "Injection Pin 4", injectionPins4
|
||||
field = "Injection Pin 5 ", injectionPins5
|
||||
field = "Injection Pin 6 ", injectionPins6
|
||||
field = "Injection Pin 7 ", injectionPins7
|
||||
field = "Injection Pin 8 ", injectionPins8
|
||||
field = "Injection Pin 9 ", injectionPins9
|
||||
field = "Injection Pin 10 ", injectionPins10
|
||||
field = "Injection Pin 11 ", injectionPins11
|
||||
field = "Injection Pin 12 ", injectionPins12
|
||||
field = "Injection Output 1", injectionPins1
|
||||
field = "Injection Output 2", injectionPins2
|
||||
field = "Injection Output 3", injectionPins3
|
||||
field = "Injection Output 4", injectionPins4
|
||||
field = "Injection Output 5 ", injectionPins5
|
||||
field = "Injection Output 6 ", injectionPins6
|
||||
field = "Injection Output 7 ", injectionPins7
|
||||
field = "Injection Output 8 ", injectionPins8
|
||||
field = "Injection Output 9 ", injectionPins9
|
||||
field = "Injection Output 10 ", injectionPins10
|
||||
field = "Injection Output 11 ", injectionPins11
|
||||
field = "Injection Output 12 ", injectionPins12
|
||||
field = auxSpeedSensorInputPin1, auxSpeedSensorInputPin1
|
||||
field = auxSpeedSensorInputPin2, auxSpeedSensorInputPin2
|
||||
|
||||
|
||||
dialog = allPins2_2
|
||||
field = "Ignition Pin 1", ignitionPins1
|
||||
field = "Ignition Pin 2", ignitionPins2
|
||||
field = "Ignition Pin 3", ignitionPins3
|
||||
field = "Ignition Pin 4", ignitionPins4
|
||||
field = "Ignition Pin 5", ignitionPins5
|
||||
field = "Ignition Pin 6", ignitionPins6
|
||||
field = "Ignition Pin 7", ignitionPins7
|
||||
field = "Ignition Pin 8", ignitionPins8
|
||||
field = "Ignition Pin 9", ignitionPins9
|
||||
field = "Ignition Pin 10", ignitionPins10
|
||||
field = "Ignition Pin 11", ignitionPins11
|
||||
field = "Ignition Pin 12", ignitionPins12
|
||||
field = "Ignition Output 1", ignitionPins1
|
||||
field = "Ignition Output 2", ignitionPins2
|
||||
field = "Ignition Output 3", ignitionPins3
|
||||
field = "Ignition Output 4", ignitionPins4
|
||||
field = "Ignition Output 5", ignitionPins5
|
||||
field = "Ignition Output 6", ignitionPins6
|
||||
field = "Ignition Output 7", ignitionPins7
|
||||
field = "Ignition Output 8", ignitionPins8
|
||||
field = "Ignition Output 9", ignitionPins9
|
||||
field = "Ignition Output 10", ignitionPins10
|
||||
field = "Ignition Output 11", ignitionPins11
|
||||
field = "Ignition Output 12", ignitionPins12
|
||||
|
||||
dialog = allPins2_3
|
||||
field = "LCD E pin", HD44780_e
|
||||
|
|
@ -2719,7 +2719,6 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
field = "SPI3 SCK", spi3sckPin, {is_enabled_spi_3 == 1} @@if_ts_show_spi
|
||||
field = "hip9011CsPin", hip9011CsPin
|
||||
field = "LIS302DLCsPin", LIS302DLCsPin
|
||||
field = "MIL / Check Engine", malfunctionIndicatorPin
|
||||
field = "Saab CDM knock", cdmInputPin
|
||||
field = "DRV8860 CS", drv8860_cs
|
||||
field = "DRV8860 CS Mode", drv8860_csPinMode
|
||||
|
|
@ -2733,10 +2732,10 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
panel = allPinsSensors
|
||||
|
||||
dialog = allPins3_2
|
||||
field = "VVT Pin #1", vvtPins1
|
||||
field = "VVT Pin #2", vvtPins2
|
||||
field = "VVT Pin #3", vvtPins3
|
||||
field = "VVT Pin #4", vvtPins4
|
||||
field = "VVT solenoid bank 1 intake", vvtPins1
|
||||
field = "VVT solenoid bank 1 exhaust", vvtPins2
|
||||
field = "VVT solenoid bank 2 intake", vvtPins3
|
||||
field = "VVT solenoid bank 2 exhaust", vvtPins4
|
||||
field = "Aux Valve #1", auxValves1
|
||||
field = "Aux Valve #2", auxValves2
|
||||
field = "TLE8888 Chip Select", tle8888_cs @@if_ts_show_spi
|
||||
|
|
@ -2748,7 +2747,7 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
field = "Upshift Pin", tcuUpshiftButtonPin
|
||||
field = "Downshift Pin", tcuDownshiftButtonPin
|
||||
|
||||
dialog = allPins3_1_and_2, "All Pins 3/3", xAxis
|
||||
dialog = allPins3_1_and_2, "All IO 3/3", xAxis
|
||||
panel = allPins3_1
|
||||
panel = allPins3_2
|
||||
|
||||
|
|
@ -2756,7 +2755,7 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
panel = allPins1_1
|
||||
panel = allPins1_2
|
||||
|
||||
dialog = allPins1, "All Pins 1/3", xAxis
|
||||
dialog = allPins1, "All IO 1/3", xAxis
|
||||
panel = allPins1_1_and_2
|
||||
panel = allPins1_3
|
||||
|
||||
|
|
@ -2764,7 +2763,7 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
panel = allPins2_1
|
||||
panel = allPins2_2
|
||||
|
||||
dialog = allPins2, "All Pins 2/3", xAxis
|
||||
dialog = allPins2, "All IO 2/3", xAxis
|
||||
panel = allPins2_1_and_2
|
||||
panel = allPins2_3
|
||||
|
||||
|
|
@ -2942,7 +2941,7 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
|
||||
dialog = egoSettings_IO, "EGO Sensor I/O"
|
||||
field = "Input channel", afr_hwChannel
|
||||
field = "Heater pin", o2heaterPin
|
||||
field = "Heater output", o2heaterPin
|
||||
|
||||
dialog = egoSettings, "", yAxis
|
||||
field = "Enable CAN Wideband", enableAemXSeries, { canReadEnabled }
|
||||
|
|
@ -2964,9 +2963,9 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
|
||||
; Engine->idle Settings
|
||||
dialog = idleSolenoid, "Solenoid"
|
||||
field = "Idle Solenoid Pin Mode", idle_solenoidPinMode, !useStepperIdle
|
||||
field = "Idle Solenoid Pin", idle_solenoidPin, { idle_solenoidPin != 0 || !useStepperIdle }
|
||||
field = "Second Idle Solenoid Pin", secondSolenoidPin, { idle_solenoidPin != 0 || (!useStepperIdle && isDoubleSolenoidIdle ) }
|
||||
field = "Idle Solenoid Primary output", idle_solenoidPin, { idle_solenoidPin != 0 || !useStepperIdle }
|
||||
field = "Idle Solenoid Secondary output", secondSolenoidPin, { idle_solenoidPin != 0 || (!useStepperIdle && isDoubleSolenoidIdle ) }
|
||||
field = "Idle Solenoid output(s) Mode", idle_solenoidPinMode, !useStepperIdle
|
||||
field = "Idle Solenoid Frequency", idle_solenoidFrequency, !useStepperIdle
|
||||
|
||||
dialog = etbHbridgeHardware, "ETB H-Bridge Hardware"
|
||||
|
|
@ -3107,8 +3106,8 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
|
||||
; Engine->Fan Settings
|
||||
dialog = fan1Settings, "Fan 1"
|
||||
field = "Pin", fanPin
|
||||
field = "Pin mode", fanPinMode
|
||||
field = "Output", fanPin
|
||||
field = "Output mode", fanPinMode
|
||||
field = "On temperature", fanOnTemperature
|
||||
field = "Off temperature", fanOffTemperature
|
||||
field = "Enable with AC", enableFan1WithAc
|
||||
|
|
@ -3116,8 +3115,8 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
field = "Idle adder", fan1ExtraIdle
|
||||
|
||||
dialog = fan2Settings, "Fan 2"
|
||||
field = "Pin", fan2Pin
|
||||
field = "Pin mode", fan2PinMode
|
||||
field = "Output", fan2Pin
|
||||
field = "Output mode", fan2PinMode
|
||||
field = "On temperature", fan2OnTemperature
|
||||
field = "Off temperature", fan2OffTemperature
|
||||
field = "Enable with AC", enableFan2WithAc
|
||||
|
|
@ -3155,31 +3154,31 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
panel = fanIndicators
|
||||
|
||||
dialog = fuelPump, "Fuel Pump"
|
||||
field = "Pin", fuelPumpPin
|
||||
field = "Pin mode", fuelPumpPinMode
|
||||
field = "Output", fuelPumpPin
|
||||
field = "Output mode", fuelPumpPinMode
|
||||
field = "Prime duration", startUpFuelPumpDuration
|
||||
|
||||
; Controller->Actuator Outputs
|
||||
dialog = mainRelayDialog, "Main relay output"
|
||||
field = "microRusEFI main relay control is hard wired on pin #29"@@if_ts_show_main_relay_microRusEFI_message
|
||||
field = "Pin", mainRelayPin@@if_ts_show_main_relay
|
||||
field = "Pin mode", mainRelayPinMode@@if_ts_show_main_relay
|
||||
field = "Output", mainRelayPin@@if_ts_show_main_relay
|
||||
field = "Output mode", mainRelayPinMode@@if_ts_show_main_relay
|
||||
|
||||
dialog = starterRelay, "Starter relay output"
|
||||
field = "Pin", starterRelayDisablePin
|
||||
field = "Pin mode", starterRelayDisablePinMode
|
||||
field = "Output", starterRelayDisablePin
|
||||
field = "Output mode", starterRelayDisablePinMode
|
||||
|
||||
dialog = statusLeds, "Status LEDs"
|
||||
field = "Running status LED", runningLedPin
|
||||
field = "TS communication status LED", communicationLedPin
|
||||
field = "Warning LED", warningLedPin
|
||||
field = "Trigger error LED", triggerErrorPin
|
||||
field = "Trigger error LED", triggerErrorPin
|
||||
field = "Debug Trigger Sync", debugTriggerSync
|
||||
|
||||
; Engine->MIL Settings
|
||||
dialog = malfunction, "Check Engine Settings"
|
||||
field = "Pin", malfunctionIndicatorPin
|
||||
field = "Pin mode", malfunctionIndicatorPinMode
|
||||
field = "Output", malfunctionIndicatorPin
|
||||
field = "Output mode", malfunctionIndicatorPinMode
|
||||
field = "Warning Period", warningPeriod
|
||||
|
||||
dialog = softwareKnockCfg, "Sense"
|
||||
|
|
@ -3243,7 +3242,7 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
field = "ChipSelect mode", cj125CsPinMode, {isCJ125Enabled == 1}
|
||||
field = "!See also 'Controller-SPI setting'"
|
||||
field = "SPI device", cj125SpiDevice
|
||||
field = "Heater pin", wboHeaterPin, {isCJ125Enabled == 1}
|
||||
field = "Heater output", wboHeaterPin, {isCJ125Enabled == 1}
|
||||
field = "UA input", cj125ua, {isCJ125Enabled == 1}
|
||||
field = "UR input", cj125ur, {isCJ125Enabled == 1}
|
||||
field = "Is UA input divided?" cj125isUaDivided, {isCJ125Enabled == 1}
|
||||
|
|
@ -3318,12 +3317,12 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
panel = stftPartitionSettingsOverrun, {fuelClosedLoopCorrectionEnabled == 1}
|
||||
|
||||
dialog = vvtPidDialog0, "Configuration"
|
||||
field = "Activation Delay", vvtActivationDelayMs
|
||||
field = "Do not control below RPM", vvtControlMinRpm
|
||||
field = "Activation Delay", vvtActivationDelayMs
|
||||
field = "Do not control below RPM", vvtControlMinRpm
|
||||
field = "VVT solenoid bank 1 intake", vvtPins1
|
||||
field = "VVT solenoid bank 1 exhaust", vvtPins2
|
||||
field = "VVT solenoid bank 2 intake", vvtPins3
|
||||
field = "VVT solenoid bank 2 exhaust", vvtPins4
|
||||
field = "VVT solenoid bank 1 exhaust", vvtPins2
|
||||
field = "VVT solenoid bank 2 intake", vvtPins3
|
||||
field = "VVT solenoid bank 2 exhaust", vvtPins4
|
||||
field = "PWM frequency", vvtOutputFrequency1, {vvtPins1 != 0 || vvtPins2 != 0}
|
||||
field = "Detailed status in console", isVerboseAuxPid1, {vvtPins1 != 0 || vvtPins2 != 0}
|
||||
field = "VVT solenoid intake cams control direction", invertVvtControlIntake, { vvtPins1 != 0 || vvtPins3 != 0 }
|
||||
|
|
@ -3357,8 +3356,8 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
dialog = alternator, "Alternator Settings", yAxis
|
||||
field = "Enabled", isAlternatorControlEnabled
|
||||
field = "Target", targetVBatt, {isAlternatorControlEnabled == 1}
|
||||
field = "Pin", alternatorControlPin, {isAlternatorControlEnabled == 1}
|
||||
field = "Pin Mode", alternatorControlPinMode, {isAlternatorControlEnabled == 1}
|
||||
field = "Control output", alternatorControlPin, {isAlternatorControlEnabled == 1}
|
||||
field = "Control outpur mode", alternatorControlPinMode, {isAlternatorControlEnabled == 1}
|
||||
field = "PWM frequency", alternatorPwmFrequency, {isAlternatorControlEnabled == 1}
|
||||
field = "Off Above TPS", alternatorOffAboveTps, {isAlternatorControlEnabled == 1}
|
||||
field = "Detailed status in console", isVerboseAlternator, {isAlternatorControlEnabled == 1}
|
||||
|
|
@ -3372,8 +3371,8 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
field = "#% duty = Pterm + Iterm + Dterm + offset%"
|
||||
|
||||
dialog = startStopDialog, "Start/Stop Button"
|
||||
field = "Start/Stop Button Pin", startStopButtonPin
|
||||
field = "Start/Stop Button Mode", startStopButtonMode
|
||||
field = "Start/Stop Button input", startStopButtonPin
|
||||
field = "Start/Stop Button input mode", startStopButtonMode
|
||||
field = "Starter Control", starterControlPin, { starterControlPin != 0 || startStopButtonPin != 0}
|
||||
field = "Start cranking maximum time", startCrankingDuration, {startStopButtonPin != 0}
|
||||
|
||||
|
|
@ -3382,7 +3381,7 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
panel = alternator
|
||||
|
||||
dialog = speedSensorAnalog, "Speed sensor"
|
||||
field = "Input pin", vehicleSpeedSensorInputPin
|
||||
field = "Input", vehicleSpeedSensorInputPin
|
||||
field = "Filter parameter", vssFilterReciprocal, { vehicleSpeedSensorInputPin != @@ADC_CHANNEL_NONE@@ }
|
||||
|
||||
;
|
||||
|
|
@ -3429,11 +3428,11 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
field = "Smoothing factor", slowAdcAlpha
|
||||
|
||||
dialog = tachSettings, "Tachometer output"
|
||||
field = "Pin", tachOutputPin
|
||||
field = "Pin mode", tachOutputPinMode
|
||||
field = "Pulse Mode", tachPulseDurationAsDutyCycle
|
||||
field = "Output", tachOutputPin
|
||||
field = "Output mode", tachOutputPinMode
|
||||
field = "Pulse Mode", tachPulseDurationAsDutyCycle
|
||||
field = "Pulse duration", tachPulseDuractionMs
|
||||
field = "Pulse per Rev", tachPulsePerRev
|
||||
field = "Pulse per Rev", tachPulsePerRev
|
||||
|
||||
|
||||
; Board->Connection
|
||||
|
|
@ -3687,20 +3686,20 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
|
|||
field = "Transmission Controller" transmissionControllerMode, { tcuEnabled }
|
||||
|
||||
dialog = shiftSolenoidPanel, "Shift Solenoids"
|
||||
field = "Solenoid 1 Pin" tcu_solenoid1, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 1 Pin Mode" tcu_solenoid_mode1, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 2 Pin" tcu_solenoid2, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 2 Pin Mode" tcu_solenoid_mode2, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 3 Pin" tcu_solenoid3, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 3 Pin Mode" tcu_solenoid_mode3, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 4 Pin" tcu_solenoid4, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 4 Pin Mode" tcu_solenoid_mode4, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 5 Pin" tcu_solenoid5, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 5 Pin Mode" tcu_solenoid_mode5, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 6 Pin" tcu_solenoid6, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 6 Pin Mode" tcu_solenoid_mode6, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "3-2 Solenoid Pin" tcu_32_solenoid_pin, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "3-2 Solenoid Pin mode" tcu_32_solenoid_pin_mode, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 1 output" tcu_solenoid1, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 1 output Mode" tcu_solenoid_mode1, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 2 output" tcu_solenoid2, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 2 output Mode" tcu_solenoid_mode2, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 3 output" tcu_solenoid3, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 3 output Mode" tcu_solenoid_mode3, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 4 output" tcu_solenoid4, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 4 output Mode" tcu_solenoid_mode4, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 5 output" tcu_solenoid5, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 5 output Mode" tcu_solenoid_mode5, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 6 output" tcu_solenoid6, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "Solenoid 6 output Mode" tcu_solenoid_mode6, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_SimpleTransmissionController@@ || transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "3-2 Solenoid output" tcu_32_solenoid_pin, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "3-2 Solenoid output mode" tcu_32_solenoid_pin_mode, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
field = "3-2 Solenoid Frequency" tcu_32_solenoid_freq, { tcuEnabled && (transmissionControllerMode == @@TransmissionControllerMode_Gm4l6x@@) }
|
||||
|
||||
dialog = otherSolenoidPanel, "Other Solenoids"
|
||||
|
|
@ -4018,10 +4017,10 @@ dialog = tcuControls, "Transmission Settings"
|
|||
; field = "digipot CS #2", digitalPotentiometerChipSelect3
|
||||
; field = "digipot CS #3", digitalPotentiometerChipSelect4
|
||||
field = ""@@if_ts_show_hardware_simulator
|
||||
field = "trigger stimulator pin #1", triggerSimulatorPins1@@if_ts_show_hardware_simulator
|
||||
field = "trigger stimulator pin mode #1", triggerSimulatorPinModes1@@if_ts_show_hardware_simulator
|
||||
field = "trigger stimulator pin #2", triggerSimulatorPins2@@if_ts_show_hardware_simulator
|
||||
field = "trigger stimulator pin mode #2", triggerSimulatorPinModes2@@if_ts_show_hardware_simulator
|
||||
field = "trigger stimulator output #1", triggerSimulatorPins1@@if_ts_show_hardware_simulator
|
||||
field = "trigger stimulator output mode #1", triggerSimulatorPinModes1@@if_ts_show_hardware_simulator
|
||||
field = "trigger stimulator output #2", triggerSimulatorPins2@@if_ts_show_hardware_simulator
|
||||
field = "trigger stimulator output mode #2", triggerSimulatorPinModes2@@if_ts_show_hardware_simulator
|
||||
field = ""
|
||||
field = "Logic input channel 1", logicAnalyzerPins1
|
||||
field = "Logic input channel 2", logicAnalyzerPins2
|
||||
|
|
@ -4159,7 +4158,7 @@ dialog = tcuControls, "Transmission Settings"
|
|||
panel = vrThreshold2@@if_ts_show_vr_threshold_2
|
||||
|
||||
dialog = gppwm1left, ""
|
||||
field = "Pin", gppwm1_pin
|
||||
field = "Output", gppwm1_pin
|
||||
field = ""
|
||||
field = "Set frequency to 0hz for on-off mode"
|
||||
field = "Frequency", gppwm1_pwmFrequency, {gppwm1_pin != 0}
|
||||
|
|
@ -4181,7 +4180,7 @@ dialog = tcuControls, "Transmission Settings"
|
|||
panel = gppwm1Tbl, {gppwm1_pin != 0}
|
||||
|
||||
dialog = gppwm2left, ""
|
||||
field = "Pin", gppwm2_pin
|
||||
field = "Output", gppwm2_pin
|
||||
field = ""
|
||||
field = "Set frequency to 0hz for on-off mode"
|
||||
field = "Frequency", gppwm2_pwmFrequency, {gppwm2_pin != 0}
|
||||
|
|
@ -4203,7 +4202,7 @@ dialog = tcuControls, "Transmission Settings"
|
|||
panel = gppwm2Tbl, {gppwm2_pin != 0}
|
||||
|
||||
dialog = gppwm3left, ""
|
||||
field = "Pin", gppwm3_pin
|
||||
field = "Output", gppwm3_pin
|
||||
field = ""
|
||||
field = "Set frequency to 0hz for on-off mode"
|
||||
field = "Frequency", gppwm3_pwmFrequency, {gppwm3_pin != 0}
|
||||
|
|
@ -4225,7 +4224,7 @@ dialog = tcuControls, "Transmission Settings"
|
|||
panel = gppwm3Tbl, {gppwm3_pin != 0}
|
||||
|
||||
dialog = gppwm4left, ""
|
||||
field = "Pin", gppwm4_pin
|
||||
field = "Output", gppwm4_pin
|
||||
field = ""
|
||||
field = "Set frequency to 0hz for on-off mode"
|
||||
field = "Frequency", gppwm4_pwmFrequency, {gppwm4_pin != 0}
|
||||
|
|
|
|||
Loading…
Reference in New Issue