verbose idle is redundant, it's all in the log now

firmware/controllers/actuators/idle_state.txt

@@ -12,22 +12,22 @@ custom idle_state_e 4 bits, S32, @OFFSET@, [0:2], "not important"
 
 bit mightResetPid;idle: mightResetPid\nThe idea of 'mightResetPid' is to reset PID only once - each time when TPS > idlePidDeactivationTpsThreshold.\nThe throttle pedal can be pressed for a long time, making the PID data obsolete (thus the reset is required).\nWe set 'mightResetPid' to true only if PID was actually used (i.e. idlePid.getOutput() was called) to save some CPU resources.\nSee automaticIdleController().
 
-bit shouldResetPid;idle: shouldResetPid
-bit wasResetPid;idle: wasResetPid\nThis is needed to slowly turn on the PID back after it was reset.
-bit mustResetPid;idle: mustResetPid\nThis is used when the PID configuration is changed, to guarantee the reset
-bit isCranking;idle: cranking
-bit isIacTableForCoasting
-bit notIdling
-bit needReset;idle: reset
-bit isInDeadZone;idle: dead zone
-bit isBlipping
+	bit shouldResetPid;Idle: shouldResetPid
+	bit wasResetPid;Idle: wasResetPid\nThis is needed to slowly turn on the PID back after it was reset.
+	bit mustResetPid;Idle: mustResetPid\nThis is used when the PID configuration is changed, to guarantee the reset
+    bit isCranking;Idle: cranking
+    bit isIacTableForCoasting
+    bit notIdling
+	bit needReset;Idle: reset
+	bit isInDeadZone;Idle: dead zone
+	bit isBlipping
 bit useClosedLoop
 bit badTps
-bit looksLikeRunning
-bit looksLikeCoasting
-bit looksLikeCrankToIdle
-bit isVerboseIAC
-bit isIdleCoasting;idle: coasting
+	bit looksLikeRunning
+	bit looksLikeCoasting
+	bit looksLikeCrankToIdle
+    bit isIdleCoasting;Idle: coasting
+
 
 int targetRpmByClt;idle: target by CLT
 int targetRpmAcBump;idle: A/C bump

firmware/controllers/actuators/idle_thread.cpp

@@ -333,12 +333,6 @@ float IdleController::getIdlePosition(float rpm) {
 
 		bool isAutomaticIdle = tps.Valid && engineConfiguration->idleMode == IM_AUTO;
 
-		isVerboseIAC = engineConfiguration->isVerboseIAC && isAutomaticIdle;
-		if (isVerboseIAC) {
-			efiPrintf("Idle state %s", getIdle_state_e(idleState));
-			getIdlePid()->showPidStatus("idle");
-		}
-
 		finishIdleTestIfNeeded();
 		undoIdleBlipIfNeeded();
 

firmware/controllers/settings.cpp

@@ -607,10 +607,6 @@ static void enableOrDisable(const char *param, bool isEnabled) {
 	} else if (strEqualCaseInsensitive(param, "two_wire_wasted_spark")) {
 		engineConfiguration->twoWireBatchIgnition = isEnabled;
 		incrementGlobalConfigurationVersion();
-	} else if (strEqualCaseInsensitive(param, "HIP9011")) {
-		engineConfiguration->isHip9011Enabled = isEnabled;
-	} else if (strEqualCaseInsensitive(param, "verbose_idle")) {
-		engineConfiguration->isVerboseIAC = isEnabled;
 	} else if (strEqualCaseInsensitive(param, "altdebug")) {
 		engineConfiguration->isVerboseAlternator = isEnabled;
 	} else if (strEqualCaseInsensitive(param, "tpic_advanced_mode")) {
@@ -1029,7 +1025,7 @@ void setDateTime(const char * const isoDateTime) {
 void setEngineTypeAndSave(int value) {
 	setEngineType(value, true);
 }
-	
+
 void setEngineType(int value, bool isWriteToFlash) {
 	{
 #if EFI_PROD_CODE

firmware/integration/rusefi_config.txt

@@ -976,7 +976,7 @@ end_struct
 
 	bit widebandOnSecondBus,"2","1";Select which bus the wideband controller is attached to.
 	bit fuelClosedLoopCorrectionEnabled;Enables lambda sensor closed loop feedback for fuelling.
-	bit isVerboseIAC;Print details into rusEFI console\nenable verbose_idle
+	bit unused1192b2
 	bit boardUseTachPullUp,"12v","5v"
 	bit boardUseTempPullUp,"With Pull Ups","Piggyback Mode"
 	bit yesUnderstandLocking,"yes","no"

firmware/tunerstudio/rusefi.input

@@ -3432,7 +3432,6 @@ cmd_set_engine_type_default					= "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
 		field = "Use coasting idle table",	useIacTableForCoasting
 		field = "Dashpot coasting-to-idle Hold time", iacByTpsHoldTime
 		field = "Dashpot coasting-to-idle Decay time", iacByTpsDecayTime
-		field = "Detailed status in console",			isVerboseIAC
 
 	dialog = idleSettings, "", yAxis
 		field = "Idle control mode",					idleMode