* unused things
* !!! actual bug !!!
* dead
* unused
* unused
* multi-bus lua RX was just broken
* make the compiler angry about it
* dead config
* alphax 2
* just call, no store
* compiler too angry
* add info send function
* fatal if CAN not configured correctly
* build
* s
* 20hz
* update wideband firmware
Co-authored-by: Matthew Kennedy <makenne@microsoft.com>
* update test framework
* eh
* hey look it's fewer warnings
* unwind
* fix
* config
* configs
* logic
* even java had some
* no need to be a typedef
* paste in actual cylinder count
* simplify trig emulator
* spelling is hard
* fix various builds
* spelling again
* add command/button for external stimulation
* enable hw stim for HW-in-loop test
* s
* I does spelling good
* clear flag when disabled
* generate enough for console build
* don't disable that
* this test needs external stimulation enabled
* import
* ui improvements
Co-authored-by: Matthew Kennedy <makenne@microsoft.com>
* enable
* guard correctly
* h7 bit timing
* allow longer frames
* allow data smaller than maximum
* mcu temperature
* typo
* tx message
* testing
* check for CAN or FDCAN
* don't need that any more
* h7 bitrate config
* undo testing
* h7-ify msg tx
* comment
* break out SID/EID macros
* guard differently
* update ChibiOS
Co-authored-by: Matthew Kennedy <makenne@microsoft.com>
* fatal error + inhibit read on preset
* inhibit more stuff when flag is set
* don't need that message
* extract function, improve msg
* changelog entry
* smart gpio: fix tle8888 direct pin mapping for MRE
* MRE: use TLE8888 pins instead of MCU gpios that drives TLE8888
* TLE8888: cleanup
* TLE8888: do not reset driver private data on WD/undervoltage reset
* TLE8888: diagnostic updates
* TLE8888 driver: BIG driver rework
* TLE8888: check SPI answers for abnormal states
Reply with other than requested register can be a sign of:
-Power-On-Reset, then OpStat0 will be replyed
-WatchDog reset, then FWDStat1 will be replyed
-Invalid communication frame, then Diag0 will be replyed
Keep tracking last accessed register and check with the next reply.
* TLE8888: debug clean-up
* TLE8888: implement spi array write
This reduce CS inactive state time between two consequent accesses
from 8.8 uS to 1.4 uS
* TLE8888: fix PP outputs in OD mode
* TLE8888: cleanup register definitions
* TLE8888: run separate driver thread for each chip instance
Calculating poll interval for few chips become more complex, avoid
this running thread for each device.
* TLE8888: fix cypress and kinetic compilation
Both platforms define its own MAX and cause redifination error if
common.h is included in driver.
* MRE: update mapping.yaml and fix direct pin mapping for TLE8888
* TLE8888: diagnnostic: disable switch off in case of overcurrent
For all output, use current limiting instead
* TLE8888: check for overvoltage on OUT8..OUT13
* TLE8888: add TODO note about how to recover from failure condition
Currently TLE8888 automaticly recovers only from overcurrent and
(may be) overtemperature conditions.
Short to bat cause output disable (bit in OECONFIG is reset) and
needs driver/host intervention.
* TLE8888: save few bytes of RAM
* TLE8888: Lada Kalina is test mule for IDLE stepper on TLE8888
Don't forget to enable PP mode for TLE8888 outputs 21..24:
uncomment line 1087 in tle8888.c
* TLE8888: reorder code, cleanup
* TLE8888: mode all debug/statisctic to per-chip struct
* TLE8888: rework poll interval calculation
* MRE: use TLE8888 pins instead of MCU gpios that drives TLE8888 #2
* reorder
* redo injector stuff
* reorder & deadtime limits
* make 2d table bounds reasonable
* more
* only allow bench if not running
Co-authored-by: Matthew Kennedy <makenne@microsoft.com>
* switch to thread
* actually use default frequency define
* crank ADC too
* make space in RAM
* remove TS field
* this should work for test
* auto cal
* wire up bench testing
* auto gains too
* s
* fix
* rearrange a bit
* inject
* remove unused bit
* mock repair
* move
* add maintainconstantvalue
* add disable button
* cleaning
* move state inside
Co-authored-by: Matthew Kennedy <makenne@microsoft.com>
* switch to thread
* actually use default frequency define
* crank ADC too
* make space in RAM
* remove TS field
* this should work for test
* auto cal
* wire up bench testing
* s
* fix
* rearrange a bit
* inject
* remove unused bit
* mock repair
* guard for ECUs without ETB
rusefi
Matthew Kennedy
rusefillc
Andrey G
Scott Smith
David Holdeman