mirror of https://github.com/FOME-Tech/fome-fw.git
config typos
This commit is contained in:
parent
232c84a8f5
commit
010cc9c216
|
@ -1002,7 +1002,7 @@ bit launchSmoothRetard;Interpolates the Ignition Retard from 0 to 100% within th
|
|||
bit isPhaseSyncRequiredForIgnition;Some engines are OK running semi-random sequential while other engine require phase synchronization
|
||||
bit useCltBasedRpmLimit,"yes","no";If enabled, use a curve for RPM limit (based on coolant temperature) instead of a constant value.
|
||||
bit forceO2Heating,"yes","no";If enabled, don't wait for engine start to heat O2 sensors. WARNING: this will reduce the life of your sensor, as condensation in the exhaust from a cold start can crack the sensing element.
|
||||
bit invertVvtControlIntake, "retard","advance";If increased VVT duty cycle increases the indicated VVT angle, set this to 'advance'. If it decreases, set this to 'retard'. Most intake cams use 'advance', and most exhaust cams use 'retard'.
|
||||
bit invertVvtControlIntake,"retard","advance";If increased VVT duty cycle increases the indicated VVT angle, set this to 'advance'. If it decreases, set this to 'retard'. Most intake cams use 'advance', and most exhaust cams use 'retard'.
|
||||
bit invertVvtControlExhaust,"retard","advance";If increased VVT duty cycle increases the indicated VVT angle, set this to 'advance'. If it decreases, set this to 'retard'. Most intake cams use 'advance', and most exhaust cams use 'retard'.
|
||||
bit useBiQuadOnAuxSpeedSensors
|
||||
bit sdTriggerLog,"trigger","normal";'Trigger' mode will write a high speed log of trigger events (warning: uses lots of space!). 'Normal' mode will write a standard MLG of sensors, engine function, etc. similar to the one captured in TunerStudio.
|
||||
|
@ -1045,7 +1045,7 @@ custom pin_mode_e 1 bits, U08, @OFFSET@, [0:6], @@pin_mode_e_enum@@
|
|||
pid_s alternatorControl;
|
||||
pid_s etb;
|
||||
Gpio[TRIGGER_INPUT_PIN_COUNT iterate] triggerInputDebugPins;
|
||||
int16_t airTaperRpmRange;RPM range above upper limit for extra air taper,"RPM", 1, 0, 0, 1500, 0
|
||||
int16_t airTaperRpmRange;RPM range above upper limit for extra air taper;"RPM", 1, 0, 0, 1500, 0
|
||||
brain_input_pin_e turboSpeedSensorInputPin;
|
||||
int16_t tps2Min;;"ADC", 1, 0, 0, 1023, 0
|
||||
int16_t tps2Max;;"ADC", 1, 0, 0, 1023, 0
|
||||
|
@ -1159,7 +1159,7 @@ int16_t tps2Max;;"ADC", 1, 0, 0, 1023, 0
|
|||
float mapHighValueVoltage;MAP voltage for low point;"v", 1, 0, 0, 10, 2
|
||||
float egoValueShift;EGO value correction;"value", 1, 0, -10, 10, 2
|
||||
|
||||
output_pin_e[CAM_INPUTS_COUNT iterate] vvtPins;VVT output\nTODO: rename to vvtOutputs
|
||||
output_pin_e[CAM_INPUTS_COUNT iterate] vvtPins;VVT output solenoid pin for this cam
|
||||
|
||||
int crankingIACposition;This is the IAC position during cranking, some engines start better if given more air during cranking to improve cylinder filling.;"percent", 1, 0, -100, 100, 0
|
||||
float tChargeMinRpmMinTps;;"", 1, 0, 0, 3, 4
|
||||
|
@ -1258,12 +1258,12 @@ tChargeMode_e tChargeMode;
|
|||
|
||||
Gpio mc33816_cs;
|
||||
|
||||
float auxFrequencyFilter
|
||||
float auxFrequencyFilter;;"hz", 1, 0, 0, 100, 1
|
||||
int16_t vvtControlMinRpm;;"RPM", 1, 0, 0, 3000, 0
|
||||
|
||||
brain_input_pin_e[SENT_INPUT_COUNT iterate] sentInputPins;
|
||||
|
||||
int8_t launchFuelAdderPercent
|
||||
int8_t launchFuelAdderPercent;;"%", 1, 0, 0, 100, 0
|
||||
uint8_t autoscale etbJamTimeout;Time required to detect a stuck throttle.;"sec", 0.02, 0, 0, 5, 2
|
||||
uint16_t etbExpAverageLength;By the way ETB PID runs at 500hz, length in 1/500 of second here.
|
||||
|
||||
|
@ -1375,7 +1375,7 @@ float tChargeAirDecrLimit;Maximum allowed rate of decrease allowed for the estim
|
|||
|
||||
uint16_t autoscale hpfpPumpVolume;Size of the pump chamber in cc. Typical Bosch HDP5 has a 9.0mm diameter, typical BMW N* stroke is 4.4mm.;"cc", 0.001, 0, 0, 65, 3
|
||||
uint8_t hpfpActivationAngle;How long to keep the valve activated (in order to allow the pump to build pressure and keep the valve open on its own);"deg", 1, 0, 0, 255, 0
|
||||
uint8_t issFilterReciprocal
|
||||
uint8_t issFilterReciprocal;;"", 1, 0, 0, 255, 0
|
||||
uint16_t autoscale hpfpPidP;;"%/kPa", 0.001, 0, 0, 65, 3
|
||||
uint16_t autoscale hpfpPidI;;"%/kPa/lobe", 0.00001, 0, 0, 0.65, 5
|
||||
uint16_t hpfpTargetDecay;The fastest rate the target pressure can be reduced by. This is because HPFP have no way to bleed off pressure other than injecting fuel.;"kPa/s", 1, 0, 0, 65000, 0
|
||||
|
@ -1453,7 +1453,7 @@ int16_t ALSMaxDuration;;"sec", 1, 0, 0, 10, 0
|
|||
int8_t ALSMaxCLT;;"C", 1, 0, 0, 105, 0
|
||||
uint8_t alsMinTimeBetween;;"", 1, 0, 0, 20000, 0
|
||||
uint8_t alsEtbPosition;;"", 1, 0, 0, 20000, 0
|
||||
uint8_t acRelayAlternatorDutyAdder
|
||||
uint8_t acRelayAlternatorDutyAdder;;"%", 1, 0, 0, 100, 0
|
||||
uint8_t instantRpmRange;;"deg", 1, 0, 0, 250, 0
|
||||
int ALSIdleAdd;;"%", 1, 0, 0, 100, 2
|
||||
int ALSEtbAdd;;"%", 1, 0, 0, 100, 2
|
||||
|
|
Loading…
Reference in New Issue