diff --git a/firmware/tunerstudio/rusefi.input b/firmware/tunerstudio/rusefi.input
index ffe02049d4..5c4aa76c9f 100644
--- a/firmware/tunerstudio/rusefi.input
+++ b/firmware/tunerstudio/rusefi.input
@@ -1999,7 +1999,8 @@ cmd_set_engine_type_default					= "@@TS_IO_TEST_COMMAND_char@@\x00\x31\x00\x00"
 	dialog = multisparkSettings, "Multispark"
 		field = "#WARNING! These settings have the potential to overheat ignition components"
 		field = "#and cause other nasty misbehavior.  Use with care, at your own risk!"
-		field = "Enable Multiple Sparks",				multisparkEnable
+		field = "#Not recommended for use on distributor or wasted spark ignition systems."
+		field = "Enable multiple sparks",				multisparkEnable
 		panel = multisparkMain
 		panel = multisparkDwellParams
 
@@ -2614,7 +2615,7 @@ cmd_set_engine_type_default					= "@@TS_IO_TEST_COMMAND_char@@\x00\x31\x00\x00"
 	dialog = idleGating, "Idle Detection Thresholds"
 		field = "TPS threshold",	idlePidDeactivationTpsThreshold
 		field = "RPM upper limit",	idlePidRpmUpperLimit
-		field = "RPM dead zone",	idlePidRpmDeadZone
+		field = "RPM deadzone",	idlePidRpmDeadZone
 
 	dialog = idleExtra, "Extra Idle Features"
 		field = "Extra idle air if throttle pressed",						iacByTpsTaper
@@ -2627,7 +2628,7 @@ cmd_set_engine_type_default					= "@@TS_IO_TEST_COMMAND_char@@\x00\x31\x00\x00"
 	dialog = idleSettings, "", yAxis
 		field = "Idle control mode",					idleMode
 
-		field = "! Solenoid idle control requires above zero RPM"
+		field = "! Solenoid idle control is disabled at zero RPM"
 		slider = "Open loop idle position",				manIdlePosition, horizontal
 		field = ""
 
@@ -2778,26 +2779,26 @@ cmd_set_engine_type_default					= "@@TS_IO_TEST_COMMAND_char@@\x00\x31\x00\x00"
 		field = "Power region load",					stft_minPowerLoad
 
 	dialog = stftPartitionSettingsMain, "Main Region", xAxis
-		field = "Time Const",							stft_cellCfgs4_timeConstant
+		field = "Time const",							stft_cellCfgs4_timeConstant
 		field = "Max add",								stft_cellCfgs4_maxAdd
 		field = "Max remove",							stft_cellCfgs4_maxRemove
 
 	dialog = stftPartitionSettingsIdle, "Idle Region", xAxis
-		field = "Time Const",							stft_cellCfgs1_timeConstant
+		field = "Time const",							stft_cellCfgs1_timeConstant
 		field = "Max add",								stft_cellCfgs1_maxAdd
 		field = "Max remove",							stft_cellCfgs1_maxRemove
 
 	dialog = stftPartitionSettingsPower, "Power Region", xAxis
-		field = "Time Const",							stft_cellCfgs3_timeConstant
+		field = "Time const",							stft_cellCfgs3_timeConstant
 		field = "Max add",								stft_cellCfgs3_maxAdd
 		field = "Max remove",							stft_cellCfgs3_maxRemove
 
 	dialog = stftPartitionSettingsOverrun, "Overrun Region", xAxis
-		field = "Time Const",							stft_cellCfgs2_timeConstant
+		field = "Time const",							stft_cellCfgs2_timeConstant
 		field = "Max add",								stft_cellCfgs2_maxAdd
 		field = "Max remove",							stft_cellCfgs2_maxRemove
 
-	dialog = fuelClosedLoopDialog, "Short-term fuel trim"
+	dialog = fuelClosedLoopDialog, "Closed loop fuel correction"
 		field = "Enabled",								fuelClosedLoopCorrectionEnabled
 
 		field = "Startup delay"							stft_startupDelay, {fuelClosedLoopCorrectionEnabled == 1}
@@ -3056,7 +3057,7 @@ cmd_set_engine_type_default					= "@@TS_IO_TEST_COMMAND_char@@\x00\x31\x00\x00"
 ;			Cranking->Cranking Settings
 	dialog = crankingDialog, "Cranking Settings"
 		field = "Cranking RPM limit",                	cranking_rpm
-		field = "Enable cylinder cleanup",				isCylinderCleanupEnabled
+		field = "Enable flood clear",				isCylinderCleanupEnabled
 		field = ""
 		field = "Enable faster engine spin-up",			isFasterEngineSpinUpEnabled
 		panel = primingFuelPulsePanel