From df47cae9fa5d149187ebd818c203b7af43fd8087 Mon Sep 17 00:00:00 2001 From: kon Date: Sun, 2 Aug 2020 09:32:26 -0700 Subject: [PATCH] fixed some config errors --- firmware/integration/rusefi_config.txt | 24 ++++++++++++++---------- 1 file changed, 14 insertions(+), 10 deletions(-) diff --git a/firmware/integration/rusefi_config.txt b/firmware/integration/rusefi_config.txt index 29283f6954..8d6e3038b0 100644 --- a/firmware/integration/rusefi_config.txt +++ b/firmware/integration/rusefi_config.txt @@ -829,12 +829,12 @@ custom maf_sensor_type_e 4 bits, S32, @OFFSET@, [0:1], @@maf_sensor_type_e_enum@ bit showHumanReadableWarning bit stftIgnoreErrorMagnitude;+If enabled, adjust at a constant rate instead of a rate proportional to the current lambda error. This mode may be easier to tune, and more tolerant of sensor noise. Use of this mode is required if you have a narrowband O2 sensor.; bit dcMotorIdleValve;+Used on some German vehicles around late 90s: cable-operated throttle and DC motor idle air valve.\nSet the primary TPS to the cable-operated throttle's sensor\nSet the secondary TPS to the mini ETB's position sensor(s). - brain_pin_e can2TxPin;set_can2_tx_pin X - brain_pin_e can2RxPin;set_can2_rx_pin X - bit enableVerboseCan2Tx;+CAN broadcast using custom rusEFI protocol\nenable can_broadcast/disable can_broadcast - can_nbc_e can2NbcType;set can_mode X - bit can2ReadEnabled;enable can_read/disable can_read - bit can2WriteEnabled;enable can_write/disable can_write + bit unusedBit_251_12 + bit unusedBit_251_13 + bit unusedBit_251_14 + bit unusedBit_251_15 + bit unusedBit_251_16 + bit unusedBit_251_17 bit unusedBit_251_18 bit unusedBit_251_19 bit unusedBit_251_20 @@ -1104,10 +1104,14 @@ int16_t tps2Max;Full throttle#2. tpsMax value as 10 bit ADC value. Not Voltage!\ uint32_t verboseCan2BaseAddress;;"", 1, 0, 0, 536870911, 0 can_baudrate_e can2BaudRate; set can2_baudrate - bit unusedBit_251_30 - bit unusedBit_251_31 - bit unusedBit_251_32 - int[31] unused_former_warmup_target_afr;;"units", 1, 0, -20, 100, 0 + bit enableVerboseCan2Tx;+CAN broadcast using custom rusEFI protocol\nenable can_broadcast/disable can_broadcast + bit can2ReadEnabled;enable can_read/disable can_read + bit can2WriteEnabled;enable can_write/disable can_write + can_nbc_e can2NbcType;set can_mode X + brain_pin_e can2TxPin;set_can2_tx_pin X + brain_pin_e can2RxPin;set_can2_rx_pin X + uint8_t unused1108;;"units", 1, 0, -20, 100, 0 + uint32_t[3] unused_former_warmup_target_afr;;"units", 1, 0, -20, 100, 0 float boostCutPressure;kPa value at which we need to cut fuel and spark, 0 if not enabled;"kPa", 1, 0, 0, 500, 0