mirror of https://github.com/FOME-Tech/fome-fw.git
158 lines
7.0 KiB
INI
158 lines
7.0 KiB
INI
|
|
! this file defines the format of rusEfi persistent configuration structure
|
|
! this file is processed by ../java_tools/config_definition.jar tool
|
|
!
|
|
! comments start with '#'
|
|
!
|
|
! each field is declared as
|
|
! type name;comment
|
|
|
|
|
|
! all the sub-structures are going to be nested withint the primary structure, that's
|
|
! needed to get a proper TunerStudio file
|
|
struct engine_configuration_s
|
|
|
|
#define FUEL_RPM_COUNT 16
|
|
#define FUEL_LOAD_COUNT 16
|
|
|
|
struct cranking_parameters_s
|
|
float baseFuel;;"ms", 1, 0, 0, 200, 1
|
|
int16_t rpm;This value controls what RPM values we consider 'cranking' (any RPM below 'crankingRpm')\nAnything above 'crankingRpm' would be 'running';"RPM", 1, 0, 0, 3000, 0
|
|
end_struct
|
|
|
|
bits air_pressure_sensor_type_e U32 [0:1] "Custom", "DENSO183", "MPX4250", "INVALID"
|
|
bits adc_channel_e U32 [0:3] "PA0", "PA1", "PA2", "PA3", "PA4", "PA5", "PA6", "PA7", "PB0", "PB1", "PC0", "PC1", "PC2", "PC3", "PC4", "PC5"
|
|
|
|
struct air_pressure_sensor_config_s
|
|
float valueAt0;kPa value at zero volts;"kpa", 1, 0, 0, 450, 2
|
|
float valueAt5;kPa value at 5 volts;"kpa", 1, 0, 0, 450, 2
|
|
air_pressure_sensor_type_e type;
|
|
adc_channel_e hwChannel;
|
|
end_struct
|
|
|
|
|
|
#define MAP_ANGLE_SIZE 8
|
|
#define MAP_WINDOW_SIZE 8
|
|
|
|
struct MAP_sensor_config_s @brief MAP averaging configuration
|
|
float[MAP_ANGLE_SIZE] samplingAngleBins;;"RPM", 1, 0, 0.0, 18000, 2
|
|
float[MAP_ANGLE_SIZE] samplingAngle;@brief MAP averaging sampling start angle, by RPM;"deg", 1, 0, 0.0, 90, 2
|
|
float[MAP_WINDOW_SIZE] samplingWindowBins;;"RPM", 1, 0, 0.0, 18000, 2
|
|
float[MAP_WINDOW_SIZE] samplingWindow;@brief MAP averaging angle duration, by RPM;"deg", 1, 0, 0.0, 90, 2
|
|
air_pressure_sensor_config_s sensor
|
|
end_struct
|
|
|
|
struct ThermistorConf @brief Thermistor curve parameters
|
|
float tempC_1;these values are in Celcuus;"*C", 1, 0, -40, 200, 1
|
|
float tempC_2;;"*C", 1, 0, -40, 200, 1
|
|
float tempC_3;;"*C", 1, 0, -40, 200, 1
|
|
float resistance_1;;"Ohm", 1, 0, 0, 200000, 1
|
|
float resistance_2;;"Ohm", 1, 0, 0, 200000, 1
|
|
float resistance_3;;"Ohm", 1, 0, 0, 200000, 1
|
|
|
|
float bias_resistor;;"Ohm", 1, 0, 0, 200000, 1
|
|
|
|
float s_h_a;
|
|
float s_h_b;
|
|
float s_h_c;
|
|
|
|
|
|
end_struct
|
|
|
|
|
|
|
|
|
|
|
|
bits engine_type_e S32 [0:2], "AUDI_AAN", "DODGE_NEON_1995", "FORD_ASPIRE_1996", "FORD_FIESTA", "NISSAN_PRIMERA", "HONDA_ACCORD", "FORD_INLINE_6_1995", "GY6_139QMB"
|
|
engine_type_e engineType;http://rusefi.com/wiki/index.php?title=Manual:Engine_Type
|
|
|
|
int headerMagicValue;this magic number is used to make sure that what we read from Flash is in fact some configuration
|
|
|
|
#define CLT_CURVE_SIZE 16
|
|
#define IAT_CURVE_SIZE 16
|
|
#define VBAT_INJECTOR_CURVE_SIZE 8
|
|
|
|
#define IGN_LOAD_COUNT 16
|
|
#define IGN_RPM_COUNT 16
|
|
|
|
float[VBAT_INJECTOR_CURVE_SIZE] battInjectorLagCorrBins;;"V", 1, 0, 0.0, 20.0, 2
|
|
float[VBAT_INJECTOR_CURVE_SIZE] battInjectorLagCorr;;"ms/V", 1, 0, 0.0, 50.0, 2
|
|
|
|
float[CLT_CURVE_SIZE] cltFuelCorrBins;;"C", 1, 0, -100.0, 250.0, 2
|
|
float[CLT_CURVE_SIZE] cltFuelCorr;;"%", 100, 0, 0.0, 500.0, 2
|
|
|
|
float[IAT_CURVE_SIZE] iatFuelCorrBins;;"C", 1, 0, -100.0, 250.0, 2
|
|
float[IAT_CURVE_SIZE] iatFuelCorr;;"%", 100, 0, 0.0, 500.0, 2
|
|
|
|
int16_t directSelfStimulation;Should the trigger emulator push data right into trigger input, eliminating the need for physical jumper wires?\nPS: Funny name, right? :)\ntodo: make this a bit on some bit field
|
|
|
|
int16_t tpsMin;todo: extract these two fields into a structure\ntodo: we need two sets of TPS parameters - modern ETBs have to sensors;"ADC", 1, 0, 0, 1023, 0
|
|
int16_t tpsMax;tpsMax value as 10 bit ADC value. Not Voltage!;"ADC", 1, 0, 0, 1023, 0
|
|
|
|
uint16_t unused334;
|
|
|
|
|
|
int16_t tpsErrorLowValue;todo: finish implementation. These values are used for TPS disconnect detection;"*C", 1, 0, -40, 200, 1
|
|
int16_t tpsErrorHighValue;;"*C", 1, 0, -40, 200, 1
|
|
|
|
float primingSquirtDurationMs;;"*C", 1, 0, -40, 200, 1
|
|
int engineCycle;360 for two-stroke\n720 for four-stroke;"engine cycle", 1, 0, 0, 1000, 0
|
|
|
|
cranking_parameters_s cranking
|
|
MAP_sensor_config_s map;@see hasMapSensor\n@see isMapAveragingEnabled
|
|
|
|
|
|
ThermistorConf clt;todo: merge with channel settings, use full-scale Thermistor here!
|
|
ThermistorConf iat;
|
|
|
|
#define DWELL_COUNT 8
|
|
|
|
#define CRANKING_CURVE_SIZE 8
|
|
|
|
#define IGN_LOAD_COUNT 16
|
|
#define IGN_RPM_COUNT 16
|
|
|
|
|
|
float[DWELL_COUNT] sparkDwellBins;;"RPM", 1, 0.0, 0.0, 18000, 2
|
|
float[DWELL_COUNT] sparkDwell;;"ms", 1, 0.0, 0.0, 30.0, 2
|
|
|
|
float[IGN_LOAD_COUNT] ignitionLoadBins;;"Load", 1, 0.0, 0, 300.0, 2
|
|
float[IGN_RPM_COUNT] ignitionRpmBins;;"RPM", 1, 0.0, 0, 18000.0, 2
|
|
|
|
float ignitionBaseAngle;this value could be used to offset the whole ignition timing table by a constant;"RPM", 1, 0, 0, 3000.0, 0
|
|
|
|
|
|
float crankingChargeAngle;While cranking (which causes battery voltage to drop) we can calculate dwell time in shaft\ndegrees, not in absolute time as in running mode.;"deg", 1, 0, 0, 3000.0, 0
|
|
|
|
bits timing_mode_e U32 [0:0], "dynamic", "fixed"
|
|
|
|
timing_mode_e timingMode;
|
|
|
|
float fixedModeTiming;This value is used in 'fixed timing' mode, i.e. constant timing\nThis mode is useful for instance while adjusting distributor location;"RPM", 1, 0, 0, 3000.0, 0
|
|
float injectorLag;;"msec", 1, 0, -10, 25.50, 2
|
|
|
|
|
|
|
|
float[FUEL_LOAD_COUNT] fuelLoadBins;;"V", 1, 0, 0.0, 300.0, 2
|
|
float[FUEL_RPM_COUNT] fuelRpmBins;RPM is float and not integer in order to use unified methods for interpolation;"RPM", 1, 0, 0.0, 25500.0, 2
|
|
|
|
float displacement;Engine displacement, in liters\nsee also cylindersCount;"L", 1, 0, 0, 1000.0, 2
|
|
int rpmHardLimit;;"rpm", 1, 0, 0, 10000.0, 2
|
|
|
|
injection_mode_e crankingInjectionMode;
|
|
injection_mode_e injectionMode;
|
|
|
|
float globalTriggerAngleOffset;This field is the angle between Top Dead Center (TDC) and the first trigger event.\nKnowing this angle allows us to control timing and other angles in reference to TDC.;"deg", 1, 0, 0, 720, 0
|
|
float analogInputDividerCoefficient;This parameter holds the coefficient of input voltage dividers;"coef", 1, 0, 0.01, 10.0, 2
|
|
|
|
bits engine_load_mode_e U32 [0:1], "MAF", "Alpha-N", "MAP", "SPEED DENSITY"
|
|
engine_load_mode_e algorithm;This setting controls which algorithm is used for ENGINE LOAD
|
|
float vbattDividerCoeff;;"coef", 1, 0, 0.01, 20.0, 2
|
|
float fanOnTemperature;Cooling fan turn-on temperature threshold, in Celsuis;"*C", 1, 0, 0, 1000.0, 2
|
|
float fanOffTemperature;Cooling fan turn-off temperature threshold, in Celsuis;"*C", 1, 0, 0, 1000.0, 2
|
|
|
|
|
|
!bits analog_chart_e S32 [0:1], "none", "trigger", "MAP", "INVALID"
|
|
!analog_chart_e analogChartMode;
|
|
|
|
end_struct |