mirror of https://github.com/FOME-Tech/fome-fw.git
231 lines
7.1 KiB
C++
231 lines
7.1 KiB
C++
/**
|
|
* @file boards/microrusefi/board_configuration.cpp
|
|
*
|
|
*
|
|
* @brief Configuration defaults for the microRusefi board
|
|
*
|
|
* MICRO_RUS_EFI
|
|
* set engine_type 60
|
|
*
|
|
* MRE_BOARD_OLD_TEST
|
|
* set engine_type 30
|
|
*
|
|
* MRE_BOARD_NEW_TEST
|
|
* set engine_type 31
|
|
*
|
|
* See https://github.com/rusefi/rusefi/wiki/Hardware-microRusEfi-wiring
|
|
*
|
|
* @author Matthew Kennedy, (c) 2019
|
|
*/
|
|
|
|
#include "pch.h"
|
|
#include "mre_meta.h"
|
|
|
|
static void setInjectorPins() {
|
|
engineConfiguration->injectionPins[0] = MRE_INJ_1;
|
|
engineConfiguration->injectionPins[1] = MRE_INJ_2;
|
|
engineConfiguration->injectionPins[2] = MRE_INJ_3;
|
|
engineConfiguration->injectionPins[3] = MRE_INJ_4;
|
|
|
|
// Disable remainder
|
|
for (int i = 4; i < MAX_CYLINDER_COUNT;i++) {
|
|
engineConfiguration->injectionPins[i] = Gpio::Unassigned;
|
|
}
|
|
|
|
engineConfiguration->injectionPinMode = OM_DEFAULT;
|
|
}
|
|
|
|
static void setIgnitionPins() {
|
|
// todo: I wonder if these are not right in light of the network rename and the +12 VP issue?
|
|
engineConfiguration->ignitionPins[0] = Gpio::D4;
|
|
engineConfiguration->ignitionPins[1] = Gpio::D3;
|
|
engineConfiguration->ignitionPins[2] = Gpio::D2;
|
|
engineConfiguration->ignitionPins[3] = Gpio::D1;
|
|
|
|
// disable remainder
|
|
for (int i = 4; i < MAX_CYLINDER_COUNT; i++) {
|
|
engineConfiguration->ignitionPins[i] = Gpio::Unassigned;
|
|
}
|
|
|
|
engineConfiguration->ignitionPinMode = OM_DEFAULT;
|
|
}
|
|
|
|
static void setLedPins() {
|
|
#ifdef EFI_COMMUNICATION_PIN
|
|
engineConfiguration->communicationLedPin = EFI_COMMUNICATION_PIN;
|
|
#else
|
|
engineConfiguration->communicationLedPin = Gpio::E2; // d23 = blue
|
|
#endif /* EFI_COMMUNICATION_PIN */
|
|
engineConfiguration->runningLedPin = Gpio::E4; // d22 = green
|
|
engineConfiguration->warningLedPin = Gpio::E1; // d27 = orange or yellow
|
|
}
|
|
|
|
static void setupVbatt() {
|
|
/*
|
|
below 0.4
|
|
// 1k high side/1.5k low side = 1.6667 ratio divider
|
|
engineConfiguration->analogInputDividerCoefficient = 2.5f / 1.5f;
|
|
*/
|
|
|
|
// 6.8k high side/10k low side = 1.68 ratio divider
|
|
engineConfiguration->analogInputDividerCoefficient = 16.8f / 10.0f;
|
|
|
|
// set vbatt_divider 8.23
|
|
// R139=39k high side/R141=10k low side multiplied by above analogInputDividerCoefficient = 8.232f
|
|
engineConfiguration->vbattDividerCoeff = (49.0f / 10.0f) * engineConfiguration->analogInputDividerCoefficient;
|
|
// PC1, pin #1 input +12 from Main Relay. Main Relay controlled by TLE8888
|
|
engineConfiguration->vbattAdcChannel = EFI_ADC_11;
|
|
|
|
engineConfiguration->adcVcc = 3.29f;
|
|
}
|
|
|
|
static void setupTle8888() {
|
|
// on microRusEFI SPI3 is exposed on PC10/PC11 and there is interest to use SD card there
|
|
// PB3/PB4 could be either SPI1 or SP3, let's use not SPI3 to address the contention
|
|
|
|
// Enable and wire up SPI1
|
|
engineConfiguration->is_enabled_spi_1 = true;
|
|
engineConfiguration->spi1mosiPin = Gpio::B5;
|
|
engineConfiguration->spi1misoPin = Gpio::B4;
|
|
engineConfiguration->spi1sckPin = Gpio::B3;
|
|
|
|
// Chip select
|
|
engineConfiguration->tle8888_cs = Gpio::D5;
|
|
|
|
// SPI device
|
|
engineConfiguration->tle8888spiDevice = SPI_DEVICE_1;
|
|
}
|
|
|
|
static void setupEtb() {
|
|
// TLE9201 driver
|
|
// This chip has three control pins:
|
|
// DIR - sets direction of the motor
|
|
// PWM - pwm control (enable high, coast low)
|
|
// DIS - disables motor (enable low)
|
|
|
|
// PWM pin
|
|
engineConfiguration->etbIo[0].controlPin = Gpio::C7;
|
|
// DIR pin
|
|
engineConfiguration->etbIo[0].directionPin1 = Gpio::A8;
|
|
// Disable pin
|
|
engineConfiguration->etbIo[0].disablePin = Gpio::C8;
|
|
// Unused
|
|
engineConfiguration->etbIo[0].directionPin2 = Gpio::Unassigned;
|
|
|
|
// we only have pwm/dir, no dira/dirb
|
|
engineConfiguration->etb_use_two_wires = false;
|
|
}
|
|
|
|
static void setupDefaultSensorInputs() {
|
|
// trigger inputs
|
|
// tle8888 VR conditioner
|
|
engineConfiguration->triggerInputPins[0] = Gpio::C6;
|
|
engineConfiguration->triggerInputPins[1] = Gpio::Unassigned;
|
|
// Direct hall-only cam input
|
|
engineConfiguration->camInputs[0] = Gpio::A5;
|
|
|
|
// open question if it's great to have TPS in default TPS - the down-side is for
|
|
// vehicles without TPS or for first start without TPS one would have to turn in off
|
|
// to avoid cranking corrections based on wrong TPS data
|
|
engineConfiguration->tps1_1AdcChannel = MRE_IN_TPS;
|
|
engineConfiguration->tps2_1AdcChannel = EFI_ADC_NONE;
|
|
|
|
|
|
engineConfiguration->map.sensor.hwChannel = MRE_IN_MAP;
|
|
|
|
// EFI_ADC_14: "32 - AN volt 6"
|
|
engineConfiguration->afr.hwChannel = EFI_ADC_14;
|
|
|
|
engineConfiguration->clt.adcChannel = MRE_IN_CLT;
|
|
|
|
engineConfiguration->iat.adcChannel = MRE_IN_IAT;
|
|
|
|
setCommonNTCSensor(&engineConfiguration->auxTempSensor1, 2700);
|
|
setCommonNTCSensor(&engineConfiguration->auxTempSensor2, 2700);
|
|
|
|
#if HW_CHECK_MODE
|
|
engineConfiguration->auxTempSensor1.adcChannel = EFI_ADC_2;
|
|
engineConfiguration->auxTempSensor2.adcChannel = EFI_ADC_3;
|
|
#endif // HW_CHECK_MODE
|
|
}
|
|
|
|
void setBoardConfigOverrides() {
|
|
setLedPins();
|
|
setupVbatt();
|
|
setupTle8888();
|
|
setupEtb();
|
|
|
|
engineConfiguration->clt.config.bias_resistor = 2700;
|
|
engineConfiguration->iat.config.bias_resistor = 2700;
|
|
|
|
engineConfiguration->canTxPin = Gpio::B6;
|
|
engineConfiguration->canRxPin = Gpio::B12;
|
|
|
|
// SPI2 for onboard SD card on v0.6.0
|
|
engineConfiguration->is_enabled_spi_2 = true;
|
|
engineConfiguration->spi2mosiPin = Gpio::B15;
|
|
engineConfiguration->spi2misoPin = Gpio::B14;
|
|
engineConfiguration->spi2sckPin = Gpio::B13;
|
|
|
|
// SPI3 for expansion header
|
|
// Don't override enable since you might want these pins for something else
|
|
engineConfiguration->spi3mosiPin = Gpio::C12;
|
|
engineConfiguration->spi3misoPin = Gpio::C11;
|
|
engineConfiguration->spi3sckPin = Gpio::C10;
|
|
}
|
|
|
|
/**
|
|
* @brief Board-specific configuration defaults.
|
|
*
|
|
* See also setDefaultEngineConfiguration
|
|
*
|
|
* @todo Add your board-specific code, if any.
|
|
*/
|
|
void setBoardDefaultConfiguration() {
|
|
setInjectorPins();
|
|
setIgnitionPins();
|
|
|
|
// MRE has a special main relay control low side pin
|
|
// rusEfi firmware is totally not involved with main relay control on microRusEfi board
|
|
// todo: maybe even set EFI_MAIN_RELAY_CONTROL to FALSE for MRE configuration
|
|
// TLE8888 half bridges (pushpull, lowside, or high-low) TLE8888_IN11 / TLE8888_OUT21
|
|
// Gpio::TLE8888_PIN_21: "35 - GP Out 1"
|
|
engineConfiguration->fuelPumpPin = Gpio::TLE8888_PIN_21;
|
|
|
|
// engineConfiguration->isSdCardEnabled = true;
|
|
|
|
// TLE8888 high current low side: VVT2 IN9 / OUT5
|
|
// Gpio::E10: "3 - Lowside 2"
|
|
engineConfiguration->idle.solenoidPin = Gpio::TLE8888_PIN_5;
|
|
|
|
|
|
// Gpio::TLE8888_PIN_22: "34 - GP Out 2"
|
|
engineConfiguration->fanPin = Gpio::TLE8888_PIN_22;
|
|
|
|
// "required" hardware is done - set some reasonable defaults
|
|
setupDefaultSensorInputs();
|
|
|
|
// Enable onboard SD card on v0.6.0
|
|
engineConfiguration->sdCardSpiDevice = SPI_DEVICE_2;
|
|
engineConfiguration->isSdCardEnabled = true;
|
|
engineConfiguration->sdCardCsPin = Gpio::E15;
|
|
|
|
// Don't enable expansion header SPI by default
|
|
engineConfiguration->is_enabled_spi_3 = false;
|
|
|
|
engineConfiguration->specs.cylindersCount = 4;
|
|
engineConfiguration->specs.firingOrder = FO_1_3_4_2;
|
|
|
|
engineConfiguration->ignitionMode = IM_INDIVIDUAL_COILS; // IM_WASTED_SPARK
|
|
engineConfiguration->crankingInjectionMode = IM_SIMULTANEOUS;
|
|
engineConfiguration->injectionMode = IM_SIMULTANEOUS;//IM_BATCH;// IM_SEQUENTIAL;
|
|
}
|
|
|
|
int getBoardMetaOutputsCount() {
|
|
return efi::size(MRE_OUTPUTS);
|
|
}
|
|
|
|
Gpio* getBoardMetaOutputs() {
|
|
return MRE_OUTPUTS;
|
|
}
|