From 654f9ef4f27b2753855b81a34f45cc80d3d79981 Mon Sep 17 00:00:00 2001 From: Piotr Rogowski Date: Wed, 28 Jun 2023 20:00:18 +0200 Subject: [PATCH] Format + typo --- .vscode/settings.json | 2 ++ ...art to fuel tuning.md => 01-Quick-Start-to-fuel-tuning.md} | 4 +++- 2 files changed, 5 insertions(+), 1 deletion(-) rename docs/Fundamentals-Of-Tuning/{01-Quick Start to fuel tuning.md => 01-Quick-Start-to-fuel-tuning.md} (98%) diff --git a/.vscode/settings.json b/.vscode/settings.json index 9552564..4d21814 100644 --- a/.vscode/settings.json +++ b/.vscode/settings.json @@ -26,6 +26,8 @@ "nofollow", "pinout", "Polygonus", + "powerband", + "pushrod", "standardised", "togethor", "UEGO", diff --git a/docs/Fundamentals-Of-Tuning/01-Quick Start to fuel tuning.md b/docs/Fundamentals-Of-Tuning/01-Quick-Start-to-fuel-tuning.md similarity index 98% rename from docs/Fundamentals-Of-Tuning/01-Quick Start to fuel tuning.md rename to docs/Fundamentals-Of-Tuning/01-Quick-Start-to-fuel-tuning.md index 7d280e4..94634f0 100644 --- a/docs/Fundamentals-Of-Tuning/01-Quick Start to fuel tuning.md +++ b/docs/Fundamentals-Of-Tuning/01-Quick-Start-to-fuel-tuning.md @@ -1,4 +1,5 @@ These instructions make some pretty serious assumptions: + 1. You have a setup that isn't going to grenade if you get things wrong for a few seconds 2. You know to lift off the throttle quickly if things are wrong 3. Your ignition maps are safe. THIS IS A BIG ASSUMPTION. @@ -7,6 +8,7 @@ These instructions make some pretty serious assumptions: If you are not sure about your ignition maps, have a high-strung engine likely to blow up and hurt things, DO NOT DO THIS. These instructions assume a certain degree of forgiveness, which all engines are not necessarily going to give you. Roughing in a fuel/VE map: + 1. Estimate maximum VE value. For something like a 70s pushrod V8, this is probably 85-90%. For a modern overhead cam 4 valve head, this is probably more like 95%. For a very modern engine with VVT and high quality heads, this could be as high as 100%. 2. Set VE table to expected maximum value for loads 90kpa - 100kpa. set target AFR to something safe and THE SAME ACROSS THE BOARD i.e. 0.8 lambda everywhere 3. run engine hard, log AFR. We're talking Wide Open Throttle (WOT) operation @@ -15,7 +17,7 @@ Roughing in a fuel/VE map: 6. set entire table vertically (i.e. same RPM different load) as WOT VE 7. Pick a couple of part throttle load points. Adjust VE at part throttle load points to achieve target AFR. Apply same correction to all RPM points at chosen load. 8. Interpolate from chosen VE points vertically to WOT (or the next highest VE point you tuned) -9. extrapolate trends to lowest thottle loads +9. extrapolate trends to lowest throttle loads 10. Set more reasonable target AFRs (i.e. 1.0 lambda at part throttle, 0.85 lambda at power desired) 11. adjust injector latency to achieve reasonable idle AFRs 12. revisit part throttle VE after latency changes with the expectation of small change in the opposite direction as latency changes. i.e. if you increased latency, expect to decrease VE but only a very small amount