rusefi/firmware/controllers/algo/wall_fuel.cpp

/*
 * @file wall_fuel.cpp
 *
 * @author Matthew Kennedy
 */

#include "pch.h"
#include "wall_fuel.h"

void WallFuel::resetWF() {
	wallFuel = 0;
}

float WallFuel::adjust(float desiredMassGrams) {
	invocationCounter++;
	if (std::isnan(desiredMassGrams)) {
		return desiredMassGrams;
	}

	ScopePerf perf(PE::WallFuelAdjust);

	/*
		this math is based on
				SAE 810494 by C. F. Aquino
				SAE 1999-01-0553 by Peter J Maloney

		M_cmd = commanded fuel mass (output of this function)
		desiredMassGrams = desired fuel mass (input to this function)
		fuelFilmMass = fuel film mass (how much is currently on the wall)

		First we compute how much fuel to command, by accounting for
		a) how much fuel will evaporate from the walls, entering the air
		b) how much fuel from the injector will hit the walls, being deposited

		Next, we compute how much fuel will be deposited on the walls.  The net
		effect of these two steps is computed (some leaves walls, some is deposited)
		and stored back in fuelFilmMass.

		alpha describes the amount of fuel that REMAINS on the wall per cycle.
		It is computed as a function of the evaporation time constant (tau) and
		the time the fuel spent on the wall this cycle, (recriprocal RPM).

		beta describes the amount of fuel that hits the wall.
	*/

	// If disabled, pass value through
	if (!engine->module<WallFuelController>()->getEnable()) {
		return desiredMassGrams;
	}

	float alpha = engine->module<WallFuelController>()->getAlpha();
	float beta = engine->module<WallFuelController>()->getBeta();

	float fuelFilmMass = wallFuel;
	float M_cmd = (desiredMassGrams - (1 - alpha) * fuelFilmMass) / (1 - beta);

	// We can't inject a negative amount of fuel
	// If this goes below zero we will be over-fueling slightly,
	// but that's ok.
	if (M_cmd <= 0) {
		M_cmd = 0;
	}

	// remainder on walls from last time + new from this time
	float fuelFilmMassNext = alpha * fuelFilmMass + beta * M_cmd;

	wallFuel = fuelFilmMassNext;
	wallFuelCorrection = M_cmd - desiredMassGrams;
	return M_cmd;
}

float WallFuel::getWallFuel() const {
	return wallFuel;
}

float WallFuelController::computeTau() const {
	if (!engineConfiguration->complexWallModel) {
		return engineConfiguration->wwaeTau;
	}

	// Default to normal operating temperature in case of
	// CLT failure, this is not critical to get perfect
	float clt = Sensor::get(SensorType::Clt).value_or(90);

	float tau = interpolate2d(
		clt,
		config->wwCltBins,
		config->wwTauCltValues
	);

	// If you have a MAP sensor, apply MAP correction
	if (Sensor::hasSensor(SensorType::Map)) {
		auto map = Sensor::get(SensorType::Map).value_or(60);

		tau *= interpolate2d(
			map,
			config->wwMapBins,
			config->wwTauMapValues
		);
	}

	return tau;
}

float WallFuelController::computeBeta() const {
	if (!engineConfiguration->complexWallModel) {
		return engineConfiguration->wwaeBeta;
	}

	// Default to normal operating temperature in case of
	// CLT failure, this is not critical to get perfect
	float clt = Sensor::get(SensorType::Clt).value_or(90);

	float beta = interpolate2d(
		clt,
		config->wwCltBins,
		config->wwBetaCltValues
	);

	// If you have a MAP sensor, apply MAP correction
	if (Sensor::hasSensor(SensorType::Map)) {
		auto map = Sensor::get(SensorType::Map).value_or(60);

		beta *= interpolate2d(
			map,
			config->wwMapBins,
			config->wwBetaMapValues
		);
	}

	// Clamp to 0..1 (you can't have more than 100% of the fuel hit the wall!)
	return clampF(0, beta, 1);
}

void WallFuelController::onFastCallback() {
	// disable wall wetting cranking
	// TODO: is this correct? Why not correct for cranking?
	if (engine->rpmCalculator.isCranking()) {
		m_enable = false;
		return;
	}

	float tau = computeTau();
	float beta = computeBeta();

	// if tau or beta is really small, we get div/0.
	// you probably meant to disable wwae.
	if (tau < 0.01f || beta < 0.01f) {
		m_enable = false;
		return;
	}

	auto rpm = Sensor::getOrZero(SensorType::Rpm);

	// Ignore low RPM
	if (rpm < 100) {
		m_enable = false;
		return;
	}

	float alpha = expf_taylor(-120 / (rpm * tau));

	// If beta is larger than alpha, the system is underdamped.
	// For reasonable values {tau, beta}, this should only be possible
	// at extremely low engine speeds (<300rpm ish)
	// Clamp beta to less than alpha.
	if (beta > alpha) {
		beta = alpha;
	}

	// Store parameters so the model can read them
	m_alpha = alpha;
	m_beta = beta;
	m_enable = true;
}