diff --git a/firmware/integration/rusefi_config.txt b/firmware/integration/rusefi_config.txt
index 8ccb80867e..31f593588f 100644
--- a/firmware/integration/rusefi_config.txt
+++ b/firmware/integration/rusefi_config.txt
@@ -97,13 +97,13 @@
 ! this is used to confirm that firmware and TunerStudio are using the same rusefi.ini version
 ! todo: this not needed in light of TS_SIGNATURE but rusEFI console still uses it. Need to migrate
 ! rusEFI console from TS_FILE_VERSION to TS_SIGNATURE :(
-#define TS_FILE_VERSION 20240404
+#define TS_FILE_VERSION 20241104
 
 ! This is the version of the data stored in flash configuration
 ! Any time an incompatible change is made to the configuration format stored in flash,
 ! update this string to the current date! It is required to also update TS_SIGNATURE above
 ! when this happens.
-#define FLASH_DATA_VERSION 20016
+#define FLASH_DATA_VERSION 20024
 
 ! this offset is part of console compatibility mechanism, please DO NOT change this offset
 #define TS_FILE_VERSION_OFFSET 124
@@ -1079,10 +1079,6 @@ bit launchSparkCutEnable;This is the Cut Mode normally used
 	bit torqueReductionEnabled
 	bit torqueReductionTriggerPinInverted
 	bit limitTorqueReductionTime
-	bit unusedFancy7
-	bit unusedFancy8
-	bit unusedFancy9
-	bit unusedFancy10
 bit verboseIsoTp;Are you a developer troubleshooting TS over CAN ISO/TP?
 bit engineSnifferFocusOnInputs
 bit launchActivateInverted
@@ -1109,7 +1105,6 @@ custom idle_mode_e 1 bits, U08, @OFFSET@, [0:0], "Open Loop + Closed Loop", "Ope
 	bit isWaveAnalyzerEnabled
 	bit useSeparateVeForIdle;This activates a separate fuel table for Idle, this allows fine tuning of the idle fuelling.
 	bit verboseTriggerSynchDetails;Verbose info in console below engineSnifferRpmThreshold\nenable trigger_details
-	bit unused1188b12
 	bit cutFuelInAcr
 	bit hondaK
 	bit twoWireBatchIgnition;This is needed if your coils are individually wired (COP) and you wish to use batch ignition (Wasted Spark).
@@ -1207,8 +1202,6 @@ int16_t tps2Max;Full throttle#2. tpsMax value as 10 bit ADC value. Not Voltage!\
 	bit luaCanRxWorkaround;global_can_data performance hack
 	bit flexSensorInverted,"Inverted","Normal"
 	bit useHardSkipInTraction
-	bit unusedHere1212
-	bit unusedHere1213
 	bit useAuxSpeedForSlipRatio;Use Aux Speed 1 as one of speeds for wheel slip ratio?
 	bit useVssAsSecondWheelSpeed;VSS and Aux Speed 1 or Aux Speed 1 with Aux Speed 2?
 	bit is_enabled_spi_5
@@ -1216,7 +1209,6 @@ int16_t tps2Max;Full throttle#2. tpsMax value as 10 bit ADC value. Not Voltage!\
 	bit enableAemXSeriesEgt;AEM X-Series EGT gauge kit or rusEFI EGT sensor from Wideband controller
 	bit startRequestPinInverted,"Inverted","Normal"
 	bit tcu_rangeSensorPulldown
-	bit unusedBit2423423
 	bit brakePedalPinInverted,"Inverted","Normal"
 	bit devBit0
 	bit devBit1
@@ -1226,7 +1218,6 @@ int16_t tps2Max;Full throttle#2. tpsMax value as 10 bit ADC value. Not Voltage!\
 	bit devBit5
 	bit devBit6
 	bit devBit7
-	bit unusedSkipWasHere
 	bit invertExhaustCamVVTSignal,"Falling","Rising"
 	bit enableKnockSpectrogram
 	bit enableKnockSpectrogramFilter
@@ -1234,9 +1225,6 @@ int16_t tps2Max;Full throttle#2. tpsMax value as 10 bit ADC value. Not Voltage!\
 	int16_t afterCrankingIACtaperDuration;This is the duration in cycles that the IAC will take to reach its normal idle position, it can be used to hold the idle higher for a few seconds after cranking to improve startup.\Should be 100 once tune is better;"cycles", 1, 0, 0, 5000, 0
 	int16_t iacByTpsTaper;IAC Value added when coasting and transitioning into idle.;"percent", 1, 0, 0, 500, 0
 
-	Gpio unusedAuxSeria
-	Gpio unusedAuxSerialRx
-
 	Gpio accelerometerCsPin;
 	uint8_t coastingFuelCutVssLow;Below this speed, disable DFCO. Use this to prevent jerkiness from fuel enable/disable in low gears.;"kph", 1, 0, 0, 255, 0
 	uint8_t coastingFuelCutVssHigh;Above this speed, allow DFCO. Use this to prevent jerkiness from fuel enable/disable in low gears.;"kph", 1, 0, 0, 255, 0
@@ -1788,8 +1776,6 @@ uint8_t[CLT_CURVE_SIZE] autoscale iacCoasting;    RPM-based idle position for co
 
 warning_message_t warning_message;
 
-    uint8_t[16] unusedGapHere
-
 uint8_t[BOOST_LOAD_COUNT x BOOST_RPM_COUNT] autoscale boostTableOpenLoop;;"", {1/2}, 0, 0, 100, 1
 uint8_t[BOOST_RPM_COUNT] autoscale boostRpmBins;;"RPM", 100, 0, 0, 25000, 0