logging of live data structs was: data points #3614

firmware/console/binary/output_channels.txt

@@ -14,11 +14,8 @@ bit checkEngine;
 bit needBurn;
 
 bit sd_msd
-bit clutchUpState;@@INDICATOR_NAME_CLUTCH_UP@@
-bit clutchDownState;@@INDICATOR_NAME_CLUTCH_DOWN@@
 bit isFan2On
 bit alternatorOnOff;
-bit brakePedalState;@@INDICATOR_NAME_BRAKE_DOWN@@
 bit toothLogReady;
 bit unused3123
 bit isTpsError;
@@ -296,12 +293,6 @@ uint16_t rpmAcceleration;dRPM;"RPM/s",1, 0, 0, 5, 0
 	int16_t autoscale auxLinear1;@@GAUGE_NAME_AUX_LINEAR_1@@;"", 0.01, 0, 0, 0, 0
 	int16_t autoscale auxLinear2;@@GAUGE_NAME_AUX_LINEAR_2@@;"", 0.01, 0, 0, 0, 0
 
-	bit launchSpeedCondition
-	bit launchRpmCondition
-	bit launchTpsCondition
-	bit launchActivateSwitchCondition
-	bit launchIsLaunchCondition;
-	bit launchCombinedConditions
 	bit dfcoActive
 	bit tpsAccelActive
 
@@ -313,9 +304,6 @@ uint16_t rpmAcceleration;dRPM;"RPM/s",1, 0, 0, 5, 0
 	int8_t autoscale boostControllerClosedLoopPart;@@GAUGE_NAME_BOOST_CLOSED_LOOP@@;"%", 0.5, 0, -50, 50, 1
 	uint8_t detectedGear;@@GAUGE_NAME_DETECTED_GEAR@@;"", 1, 0, 0, @@GEARS_COUNT@@, 0
 
-	int16_t autoscale unusedAimingCltCorrection;;"deg",{1/@@PACK_MULT_PERCENT@@}, 0, -20, 20, 2
-	int16_t autoscale unusedAtimingIatCorrection;;"deg",{1/@@PACK_MULT_PERCENT@@}, 0, -20, 20, 2
-	int16_t autoscale unusedAtimingPidCorrection;;"deg",{1/@@PACK_MULT_PERCENT@@}, 0, -20, 20, 2
 	uint16_t autoscale instantMAPValue;Instant MAP;"kPa",{1/@@PACK_MULT_PRESSURE@@}, 0, 0, 655, 2
 
     uint16_t mostRecentTimeBetweenSparkEvents;;"", 1, 0, -10000, 10000, 3
@@ -344,8 +332,6 @@ uint16_t rpmAcceleration;dRPM;"RPM/s",1, 0, 0, 5, 0
     float injectorFlowPressureRatio;;"", 1, 0, -10000, 10000, 3
     float injectorFlowPressureDelta;;"kPa", 1, 0, -10000, 10000, 1
 
-    float etbIntegralError;;"", 1, 0, -10000, 10000, 3
-    float etbCurrentTarget;;"%", 1, 0, -10000, 10000, 3
 	pid_status_s alternatorStatus
 	pid_status_s idleStatus
 	pid_status_s etbStatus

firmware/controllers/actuators/electronic_throttle.cpp

@@ -303,8 +303,7 @@ expected<percent_t> EtbController::getSetpointEtb() {
 	float sanitizedPedal = clampF(0, pedalPosition.value_or(0), 100);
 	
 	float rpm = Sensor::getOrZero(SensorType::Rpm);
-	float targetFromTable = m_pedalMap->getValue(rpm, sanitizedPedal);
+	etbCurrentTarget = m_pedalMap->getValue(rpm, sanitizedPedal);
-	engine->engineState.targetFromTable = targetFromTable;
 
 	percent_t etbIdlePosition = clampF(
 									0,
@@ -317,7 +316,7 @@ expected<percent_t> EtbController::getSetpointEtb() {
 	// [0, 100] -> [idle, 100]
 	// 0% target from table -> idle position as target
 	// 100% target from table -> 100% target position
-	idlePosition = interpolateClamped(0, etbIdleAddition, 100, 100, targetFromTable);
+	idlePosition = interpolateClamped(0, etbIdleAddition, 100, 100, etbCurrentTarget);
 
 	percent_t targetPosition = idlePosition + luaAdjustment;
 
@@ -504,16 +503,10 @@ expected<percent_t> EtbController::getClosedLoop(percent_t target, percent_t obs
 		return getClosedLoopAutotune(target, observation);
 	} else {
 		// Check that we're not over the error limit
-		float errorIntegral = m_errorAccumulator.accumulate(target - observation);
+		etbIntegralError = m_errorAccumulator.accumulate(target - observation);
-
-#if EFI_TUNER_STUDIO
-		if (m_function == ETB_Throttle1) {
-			engine->outputChannels.etbIntegralError = errorIntegral;
-		}
-#endif // EFI_TUNER_STUDIO
 
 		// Allow up to 10 percent-seconds of error
-		if (errorIntegral > 10.0f) {
+		if (etbIntegralError > 10.0f) {
 			// TODO: figure out how to handle uncalibrated ETB 
 			//engine->limpManager.etbProblem();
 		}
@@ -573,7 +566,6 @@ void EtbController::update() {
 		}
 	}
 
-	engine->outputChannels.etbCurrentTarget = engine->engineState.targetFromTable;
 
 	m_pid.iTermMin = engineConfiguration->etb_iTermMin;
 	m_pid.iTermMax = engineConfiguration->etb_iTermMax;

firmware/controllers/actuators/electronic_throttle.txt

@@ -4,6 +4,9 @@ float idlePosition
 float trim
 float luaAdjustment
 
+	percent_t etbFeedForward
+    float etbIntegralError;;"", 1, 0, -10000, 10000, 3
+    float etbCurrentTarget;;"%", 1, 0, -10000, 10000, 3
 
 
 end_struct

firmware/controllers/algo/engine_state.txt

@@ -74,10 +74,6 @@ running_fuel_s running
 
 	custom percent_t 4 scalar, F32, @OFFSET@, "", 1, 0, 0, 100, 2
 
-	! todo: move these to ETB state, not engine
-	percent_t etbFeedForward
-	percent_t targetFromTable
-
 	! spark-related
 	floatms_t sparkDwell;ignition dwell duration in ms\nSee also dwellAngle
 	angle_t dwellAngle;ignition dwell duration as crankshaft angle\nNAN if engine is stopped\nSee also sparkDwell
@@ -88,6 +84,9 @@ running_fuel_s running
     int16_t hellenBoardId;How does this board self identifies;"id", 1, 0, 0, 3000, 0
 
     bit clutchDownState
+    bit clutchUpState;@@INDICATOR_NAME_CLUTCH_UP@@
+    bit clutchDownState;@@INDICATOR_NAME_CLUTCH_DOWN@@
+    bit brakePedalState;@@INDICATOR_NAME_BRAKE_DOWN@@
 
 ! engine_state2_s
 end_struct