From bacbb99ff078bf5bd9e1864ec4ee9c954f43ead6 Mon Sep 17 00:00:00 2001 From: Matthew Kennedy Date: Mon, 5 Jun 2023 03:13:45 -0400 Subject: [PATCH] status LED UI is dead! --- firmware/integration/rusefi_config.txt | 8 ++------ firmware/tunerstudio/rusefi.input | 12 ------------ 2 files changed, 2 insertions(+), 18 deletions(-) diff --git a/firmware/integration/rusefi_config.txt b/firmware/integration/rusefi_config.txt index ec18c35534..4827dfb888 100644 --- a/firmware/integration/rusefi_config.txt +++ b/firmware/integration/rusefi_config.txt @@ -494,7 +494,6 @@ float cylinderBore;Cylinder diameter in mm.;"mm", 1, 0, 0, 20000, 2 custom engine_load_mode_e 1 bits, U08, @OFFSET@, [0:2], @@engine_load_mode_e_enum@@ engine_load_mode_e fuelAlgorithm;This setting controls which fuel quantity control algorithm is used.\nAlpha-N means drive by TPS commonly only used for NA engines\nSpeed Density requires MAP sensor and is the default choice for may installs\nMAF air charge is a cylinder filling based method that uses a mass air flow sensor.; uint8_t ALSMaxTPS;;"%", 1, 0, 0, 10, 0 -Gpio criticalLedPin; custom injection_mode_e 1 bits, U08, @OFFSET@, [0:1], "Simultaneous", "Sequential", "Batch", "Single Point" injection_mode_e crankingInjectionMode;This is the injection strategy during engine start. See Fuel/Injection settings for more detail. It is suggested to use "Simultaneous". @@ -1091,8 +1090,6 @@ int16_t tps2Max;Full throttle#2. tpsMax value as 10 bit ADC value. Not Voltage!\ pid_s idleRpmPid;See cltIdleRpmBins float wwaeBeta;0 = No fuel settling on port walls 1 = All the fuel settling on port walls setting this to 0 disables the wall wetting enrichment. ;"Fraction", 1, 0, 0, 1, 2 - Gpio communicationLedPin;blue LED on many rusEFI boards.\nBlue Communication LED which is expected to blink at 50% duty cycle during normal board operation.\nIf USB communication cable is connected Blue LED starts to blink faster. - Gpio runningLedPin;Green LED on many rusEFI boards.\nOff if engine is stopped, blinks if engine is cranking, solid if engine is running. Gpio binarySerialTxPin;See also EFI_CONSOLE_RX_BRAIN_PIN Gpio binarySerialRxPin; @@ -1113,9 +1110,8 @@ int16_t tps2Max;Full throttle#2. tpsMax value as 10 bit ADC value. Not Voltage!\ int16_t iacByTpsTaper;Extra IAC, in percent between 0 and 100, tapered between zero and idle deactivation TPS value;"percent", 1, 0, 0, 500, 0 - Gpio auxSerialTxPin;Auxiliary sensor serial, not to be confused with secondary calibration serial\nset_aux_tx_pin X; - Gpio warningLedPin; - Gpio auxSerialRxPin;Auxiliary sensor serial, not to be confused with secondary calibration serial\nset_aux_rx_pin X; + Gpio auxSerialTxPin;Auxiliary sensor serial, not to be confused with secondary calibration serial; + Gpio auxSerialRxPin;Auxiliary sensor serial, not to be confused with secondary calibration serial; Gpio LIS302DLCsPin; diff --git a/firmware/tunerstudio/rusefi.input b/firmware/tunerstudio/rusefi.input index 82f9eb2403..503e951714 100644 --- a/firmware/tunerstudio/rusefi.input +++ b/firmware/tunerstudio/rusefi.input @@ -272,8 +272,6 @@ enable2ndByteCanID = false requiresPowerCycle = boardUseCanTerminator requiresPowerCycle = lps25BaroSensorScl requiresPowerCycle = lps25BaroSensorSda - requiresPowerCycle = warningLedPin - requiresPowerCycle = runningLedPin requiresPowerCycle = binarySerialTxPin requiresPowerCycle = binarySerialRxPin requiresPowerCycle = tunerStudioSerialSpeed @@ -2831,8 +2829,6 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_ dialog = allPins1_1 field = "trigger stimulator output #1", triggerSimulatorPins1 field = "trigger stimulator output #2", triggerSimulatorPins2 - field = "Critical Led", criticalLedPin @@if_ts_show_critical_led - field = "Warning Led", warningLedPin field = "tle6240_cs", tle6240_cs field = "tle6240 SPI", tle6240spiDevice @@ -2924,9 +2920,6 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_ field = "DRV8860 CS Mode", drv8860_csPinMode field = "DRV8860 MISO pin", drv8860_miso field = "DRV8860 SPI", drv8860spiDevice - field = "comm status light", communicationLedPin - field = "running status light", runningLedPin - dialog = allPins3_1 panel = allPinsSensors @@ -3414,14 +3407,9 @@ cmd_set_engine_type_default = "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_ panel = fanSetting, Center dialog = statusLeds, "Status LEDs" - field = "Critical Led", criticalLedPin @@if_ts_show_critical_led - field = "Running status LED", runningLedPin - field = "TS communication status LED", communicationLedPin - field = "Warning LED", warningLedPin field = "Trigger error LED", triggerErrorPin field = "Debug Trigger Sync", debugTriggerSync - dialog = softwareKnockCfg, "Sense" field = "Enable", enableSoftwareKnock field = "Cylinder Bore", cylinderBore