diff --git a/firmware/tunerstudio/tunerstudio.template.ini b/firmware/tunerstudio/tunerstudio.template.ini
index 1d8a37f805..5173308a9f 100644
--- a/firmware/tunerstudio/tunerstudio.template.ini
+++ b/firmware/tunerstudio/tunerstudio.template.ini
@@ -305,8 +305,6 @@ enable2ndByteCanID = false
 	requiresPowerCycle = binarySerialTxPin
 	requiresPowerCycle = binarySerialRxPin
 	requiresPowerCycle = tunerStudioSerialSpeed
-	requiresPowerCycle = auxSerialRxPin
-	requiresPowerCycle = auxSerialTxPin
 
 	requiresPowerCycle = is_enabled_spi_1
 	requiresPowerCycle = is_enabled_spi_2
@@ -3348,8 +3346,6 @@ cmd_set_engine_type_default					= "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
 		field = "TLE8888 Chip Select",						tle8888_cs @@if_ts_show_spi
 		field = "TLE 8888 spi",								tle8888spiDevice @@if_ts_show_spi
 		field = "L9779 Chip Select",						l9779_cs @@if_ts_show_spi
-		field = "AUX Serial TX",						auxSerialTxPin
-		field = "AUX Serial RX",						auxSerialRxPin
 		field = "Start/Stop Button",					startStopButtonPin
 		field = "Upshift Pin",							tcuUpshiftButtonPin
 		field = "Downshift Pin",						tcuDownshiftButtonPin
@@ -3604,15 +3600,11 @@ cmd_set_engine_type_default					= "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
 		field = flipWboChannels,          flipWboChannels
 		field = "Force O2 sensor heating", forceO2Heating
 
-	dialog = uegoSerial, "Innovate LC-2 serial"
-		field = "Enable Innovate LC-2 Serial",			enableInnovateLC2, { auxSerialRxPin && auxSerialTxPin }
-
 	dialog = egoSettings, "", yAxis
 		panel = uegoCan
-		panel = uegoSerial@@if_ts_show_uegoSerial
 		panel = egoSettings_IO1
-		panel = egoSettings_IO2, {afr_hwChannel != @@ADC_CHANNEL_NONE@@ && enableAemXSeries == 0 && !auxSerialRxPin && !auxSerialTxPin}@@if_ts_show_ego2
-		panel = egoSettings_sensor, {afr_hwChannel != @@ADC_CHANNEL_NONE@@ && enableAemXSeries == 0 && !auxSerialRxPin && !auxSerialTxPin}
+		panel = egoSettings_IO2, {afr_hwChannel != @@ADC_CHANNEL_NONE@@ && enableAemXSeries == 0}@@if_ts_show_ego2
+		panel = egoSettings_sensor, {afr_hwChannel != @@ADC_CHANNEL_NONE@@ && enableAemXSeries == 0}
 
 ;			Engine->EGT inputs
 	dialog = egtInputsCan, "CAN EGT sensors"
@@ -4257,11 +4249,6 @@ cmd_set_engine_type_default					= "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
 		panel = canHw1
 		panel = canHw2	@@if_ts_show_can2
 
-	dialog = auxSerial, "AUX Sensor Serial"
-		field = "RX pin",								auxSerialRxPin @@if_ts_show_auxserial_pins
-		field = "TX pin",								auxSerialTxPin @@if_ts_show_auxserial_pins
-		field = "Serial Baud Rate",						auxSerialSpeed @@if_ts_show_auxserial_pins
-
 	dialog = sdCard, "SD Card Logger"
 		field = "#rusEFI logs to SD when powered without USB connected"
 		field = "# and USB not connected for 15 seconds"
@@ -4288,7 +4275,6 @@ cmd_set_engine_type_default					= "@@TS_IO_TEST_COMMAND_char@@@@ts_command_e_TS_
 	dialog = connection, "",	yAxis
 		panel = tsPort							@@if_ts_show_tunerstudio_port
 		field = "uartConsoleSerialSpeed",				uartConsoleSerialSpeed
-		panel = auxSerial
 		field = enableKline, enableKline
 
 	dialog = monitoringSettings, "rusEFI Console Settings"