* smart gpio: fix tle8888 direct pin mapping for MRE
* MRE: use TLE8888 pins instead of MCU gpios that drives TLE8888
* TLE8888: cleanup
* TLE8888: do not reset driver private data on WD/undervoltage reset
* TLE8888: diagnostic updates
* TLE8888 driver: BIG driver rework
* TLE8888: check SPI answers for abnormal states
Reply with other than requested register can be a sign of:
-Power-On-Reset, then OpStat0 will be replyed
-WatchDog reset, then FWDStat1 will be replyed
-Invalid communication frame, then Diag0 will be replyed
Keep tracking last accessed register and check with the next reply.
* TLE8888: debug clean-up
* TLE8888: implement spi array write
This reduce CS inactive state time between two consequent accesses
from 8.8 uS to 1.4 uS
* TLE8888: fix PP outputs in OD mode
* TLE8888: cleanup register definitions
* TLE8888: run separate driver thread for each chip instance
Calculating poll interval for few chips become more complex, avoid
this running thread for each device.
* TLE8888: fix cypress and kinetic compilation
Both platforms define its own MAX and cause redifination error if
common.h is included in driver.
* MRE: update mapping.yaml and fix direct pin mapping for TLE8888
* TLE8888: diagnnostic: disable switch off in case of overcurrent
For all output, use current limiting instead
* TLE8888: check for overvoltage on OUT8..OUT13
* TLE8888: add TODO note about how to recover from failure condition
Currently TLE8888 automaticly recovers only from overcurrent and
(may be) overtemperature conditions.
Short to bat cause output disable (bit in OECONFIG is reset) and
needs driver/host intervention.
* TLE8888: save few bytes of RAM
* TLE8888: Lada Kalina is test mule for IDLE stepper on TLE8888
Don't forget to enable PP mode for TLE8888 outputs 21..24:
uncomment line 1087 in tle8888.c
* TLE8888: reorder code, cleanup
* TLE8888: mode all debug/statisctic to per-chip struct
* TLE8888: rework poll interval calculation
* MRE: use TLE8888 pins instead of MCU gpios that drives TLE8888 #2
* add
* remove old
* remove more old
* makefile
* fix init
* patch up other stuff
* actually fix it this time
* raw output channels
* gauges, UI
* scaled channel
* fix field ordering
* two throttles one thread
* look at all this RAM!
* add enum
* switch from index to function
* test fixup
* improve init logic
* remove old vw idle mode bit
* Update tachometer.cpp
Initial implementation of E30 M3 Tach output solution #907, unit_test plus debugging next
* tacho unit tests
First successfull unit test for tachometer
* RAM adjustment so it would link
* refactoring tacho, broken!
* starting to make some progress...still fails after a few seconds
* Rework with SW PWM
* Update after code review
* unit_test update
* First working unit_test
* Update .gitignore
* Update engine_controller.cpp
* Update engine_controller.cpp
* Update tachometer.h
* Update test_tacho.cpp
* Switched UART DMA on
* Revert "Switched UART DMA on"
This reverts commit 4a23974c431e0e7fd760595d2161e74e6854897e.
* enable launch control
make use of already existent code + integration
* Delete compile_frankenso_all.sh
remove it since it is not part of the project
* Update main_trigger_callback.cpp
broke unit_Tests
Co-authored-by: rusefi <rusefi@users.noreply.github.com>
* change acSwitch name, add mode
* fix
* remove some adc stuff
* remove some adc stuff
* semicolon stupid
* left behind
* add readpinstate
* wrong var name
* add functions back
* fix name
* bool, not void, plus fix name
* move
* not sure what I broke
* try setMockValue
* namespace
* whoops missed one
* switch values because adc was set up for pullup
* try 5
* comment for now
* comment for now
* uncomment tests, add function to mock, add mock to efiReadPin
* fixes
* for F's sake
* if
* add defy
* pass params
* use ASSERT_TRUE/FALSE
* advance time
* remove ifdef from readPin
* try moving if
* move to separate func
* move extern
* move include
* try engine_test_helper
* am confuse
* move func to else
* include hal
* add efi prod check
* remove include
* try extern
* move include
* semicolon stupid
* move extern again
* include
* move mockPinStates
* size
* add if
* add comment
* clean on instantiation
* add config fields
* config options
* new output channels
* dump out state to ts
* s
* implement override
* enums
* this test is no longer used
* test new behavior
* old
* comments
* impl
* unhide option
* fix
* tests
* add config fields
* config options
* new output channels
* dump out state to ts
* s
* implement override
* enums
* this test is no longer used
* test new behavior
* old
* comments
* lambda sens
* fix init
* fix
* a test for good measure
* he's climbin in your windows, snatchin you ram up
Co-authored-by: Matthew Kennedy <makenne@microsoft.com>
* s
* science
* set pin mode
* turn stuff off so it fits
* filtering maybe
* filtering actually works
* generate filter parameters internally
* shorter window
* guard behind enable flag
* use checked in filter
* add biquad reset
* tracing
* const
* exec order
* do it from a thread
* smaller buffer, comment
* configure with header
* only for proteus
* oops
* unused
* not needed
* guards
* pin config
* don't need that include
* precook filter steady state
* define sample rate
* multi cylinder knock
* TS
* only sense when running
* configurable stoich ratio
* afr table always in gas afr
* default
* typo
* use defined ratio
* do it in config too
* missed a spot
* oops wrong one
Co-authored-by: Matthew Kennedy <makenne@microsoft.com>
Matthew Kennedy
GitHub build-firmware Action
Andrey G
rusefi
rusefillc
David Holdeman
shadowm60
David Holdeman
Matthew Kennedy