rusefi/firmware/config/boards/hellen/hellen64_miataNA6_94/board_configuration.cpp

/**
 * @file boards/hellen/hellen64_miataNA6_94/board_configuration.cpp
 *
 *
 * @brief Configuration defaults for the hellen64_miataNA6_94 board
 *
 * See https://rusefi.com/s/hellenNA6
 *
 * @author andreika <prometheus.pcb@gmail.com>
 * @author Andrey Belomutskiy, (c) 2012-2020
 */

#include "pch.h"
#include "custom_engine.h"
#include "hellen_meta.h"

static void setInjectorPins() {
	engineConfiguration->injectionPins[0] = H176_LS_1;
	engineConfiguration->injectionPins[1] = GPIOG_8;
	engineConfiguration->injectionPins[2] = GPIOD_11;
	engineConfiguration->injectionPins[3] = GPIOD_10;

	// Disable remainder
	for (int i = 4; i < MAX_CYLINDER_COUNT;i++) {
		engineConfiguration->injectionPins[i] = GPIO_UNASSIGNED;
	}

	engineConfiguration->injectionPinMode = OM_DEFAULT;

	engineConfiguration->clutchDownPin = GPIOC_4; // Clutch switch input
	engineConfiguration->clutchDownPinMode = PI_PULLDOWN;
	engineConfiguration->launchActivationMode = CLUTCH_INPUT_LAUNCH;
	engineConfiguration->malfunctionIndicatorPin = GPIOG_4; //1E - Check Engine Light
}

static void setIgnitionPins() {
	engineConfiguration->ignitionPins[0] = GPIOI_8; // 3F - IGN_1 (1&4)
	engineConfiguration->ignitionPins[1] = GPIO_UNASSIGNED ; // GPIOE_4
	engineConfiguration->ignitionPins[2] = GPIOE_5; // 3I - IGN_2 (2&3)
	engineConfiguration->ignitionPins[3] = GPIO_UNASSIGNED; // GPIOE_3

	//engineConfiguration->ignitionPins[4] = GPIOE_2;
	//engineConfiguration->ignitionPins[5] = GPIOI_5;
	//engineConfiguration->ignitionPins[6] = GPIOI_6;
	//engineConfiguration->ignitionPins[7] = GPIOI_7;
	
	// disable remainder
	for (int i = 4; i < MAX_CYLINDER_COUNT; i++) {
		engineConfiguration->ignitionPins[i] = GPIO_UNASSIGNED;
	}

	engineConfiguration->ignitionPinMode = OM_DEFAULT;
}

static void setupVbatt() {
	// 4.7k high side/4.7k low side = 2.0 ratio divider
	engineConfiguration->analogInputDividerCoefficient = 2.0f;

	// set vbatt_divider 5.835
	// 33k / 6.8k
	engineConfiguration->vbattDividerCoeff = (33 + 6.8) / 6.8; // 5.835

	// pin input +12 from Main Relay
	engineConfiguration->vbattAdcChannel = EFI_ADC_5; // 4T

	engineConfiguration->adcVcc = 3.29f;
}

static void setupDefaultSensorInputs() {
	// trigger inputs, hall
	engineConfiguration->triggerInputPins[0] = GPIOA_6;
	engineConfiguration->triggerInputPins[1] = GPIOB_1;
	engineConfiguration->triggerInputPins[2] = GPIO_UNASSIGNED;
	engineConfiguration->camInputs[0] = GPIO_UNASSIGNED;

	engineConfiguration->tps1_1AdcChannel = EFI_ADC_4;
	engineConfiguration->tps2_1AdcChannel = EFI_ADC_NONE;

	engineConfiguration->mafAdcChannel = EFI_ADC_10;
	engineConfiguration->map.sensor.hwChannel = EFI_ADC_11;

	engineConfiguration->afr.hwChannel = EFI_ADC_1;

	engineConfiguration->clt.adcChannel = H144_IN_CLT;

	engineConfiguration->iat.adcChannel = H144_IN_IAT;

	engineConfiguration->auxTempSensor1.adcChannel = EFI_ADC_NONE;
	engineConfiguration->auxTempSensor2.adcChannel = EFI_ADC_NONE;
}

void setBoardConfigOverrides() {
	setHellen176LedPins();
	setupVbatt();
	setSdCardConfigurationOverrides();

	engineConfiguration->clt.config.bias_resistor = 4700;
	engineConfiguration->iat.config.bias_resistor = 4700;

	engineConfiguration->canTxPin = H176_CAN_TX;
	engineConfiguration->canRxPin = H176_CAN_RX;
}

void setSerialConfigurationOverrides() {
	engineConfiguration->useSerialPort = false;




}


/**
 * @brief   Board-specific configuration defaults.
 *
 * See also setDefaultEngineConfiguration
 *
 * @todo    Add your board-specific code, if any.
 */
void setBoardDefaultConfiguration() {
	setInjectorPins();
	setIgnitionPins();

	engineConfiguration->isSdCardEnabled = true;

	engineConfiguration->enableSoftwareKnock = true;

	// these stm32 pins do not match hellen_meta, is that because hellenNA6 is not using latest MCU version?
	engineConfiguration->acRelayPin = GPIOH_15; // 1J - AC Relay
	engineConfiguration->fuelPumpPin = GPIOG_2;	// OUT_IO9
	engineConfiguration->idle.solenoidPin = GPIOD_14;	// OUT_PWM5
	engineConfiguration->fanPin = GPIOD_12;	// OUT_PWM8
	engineConfiguration->mainRelayPin = GPIOI_2;	// OUT_LOW3
	engineConfiguration->tachOutputPin = GPIOI_0;
	engineConfiguration->malfunctionIndicatorPin = GPIOG_9;

	engineConfiguration->vehicleSpeedSensorInputPin = H144_IN_VSS;

	// "required" hardware is done - set some reasonable defaults
	setupDefaultSensorInputs();

	// Some sensible defaults for other options
	setOperationMode(engineConfiguration, FOUR_STROKE_CRANK_SENSOR);
	engineConfiguration->trigger.type = TT_TOOTHED_WHEEL_60_2;
	engineConfiguration->useOnlyRisingEdgeForTrigger = true;
	setAlgorithm(LM_SPEED_DENSITY);

	engineConfiguration->specs.cylindersCount = 4;
	engineConfiguration->specs.firingOrder = FO_1_3_4_2;

	engineConfiguration->ignitionMode = IM_INDIVIDUAL_COILS; // IM_WASTED_SPARK
	engineConfiguration->crankingInjectionMode = IM_SIMULTANEOUS;
	engineConfiguration->injectionMode = IM_SIMULTANEOUS;//IM_BATCH;// IM_SEQUENTIAL;
}

/**
 * @brief   Board-specific SD card configuration code overrides. Needed by bootloader code.
 * @todo    Add your board-specific code, if any.
 */
void setSdCardConfigurationOverrides() {
	engineConfiguration->sdCardSpiDevice = SPI_DEVICE_3;

	engineConfiguration->spi3mosiPin = GPIOC_12;
	engineConfiguration->spi3misoPin = GPIOC_11;
	engineConfiguration->spi3sckPin = GPIOC_10;
	engineConfiguration->sdCardCsPin = GPIOA_15;

//	engineConfiguration->spi2mosiPin = GPIOB_15;
//	engineConfiguration->spi2misoPin = GPIOB_14;
//	engineConfiguration->spi2sckPin = GPIOB_13;
//	engineConfiguration->sdCardCsPin = GPIOB_12;
	engineConfiguration->is_enabled_spi_3 = true;
}