195 lines
5.9 KiB
Plaintext
195 lines
5.9 KiB
Plaintext
#define TS_PROTOCOL "001"
|
|
! These commands are used by TunerStudio and the rusEFI console
|
|
! 0x4F ochGetCommand
|
|
#define TS_OUTPUT_COMMAND 'O'
|
|
! 0x53 queryCommand - this one is about detailed signature
|
|
#define TS_HELLO_COMMAND 'S'
|
|
! todo: replace all usages of TS_HELLO_COMMAND with TS_QUERY_COMMAND
|
|
! todo#2: actually is above still the case?
|
|
! TS auto-detect depends on well-known queryCommand value 'Q' which is not yet mentioned in https://www.tunerstudio.com/index.php/support/manuals/tsdevmanuals/137-ecu-definition-specification-aka-the-ini-document
|
|
! that Q command is not mentioned in the .ini neither since it could happen during ECU auto-detection phase before any .ini is available
|
|
#define TS_QUERY_COMMAND 'Q'
|
|
! 0x6B 107
|
|
#define TS_CRC_CHECK_COMMAND 'k'
|
|
|
|
|
|
! 0x50 80
|
|
#define TS_PAGE_COMMAND 'P'
|
|
! 0x46
|
|
#define TS_COMMAND_F 'F'
|
|
#define TS_GET_PROTOCOL_VERSION_COMMAND_F 'F'
|
|
! versionInfo 0x56 86 this one is only used for TS title bar
|
|
#define TS_GET_FIRMWARE_VERSION 'V'
|
|
! returns getFirmwareError(), works together with ind_hasFatalError
|
|
#define TS_GET_CONFIG_ERROR 'e'
|
|
|
|
#define TS_SIMULATE_CAN '>'
|
|
|
|
! 0x42 burnCommand
|
|
#define TS_BURN_COMMAND 'B'
|
|
! 0x77
|
|
#define TS_IO_TEST_COMMAND 'Z'
|
|
|
|
#define TS_RESPONSE_OK 0
|
|
#define TS_RESPONSE_BURN_OK 4
|
|
|
|
! Engine Sniffer time stamp unit, in microseconds
|
|
#define ENGINE_SNIFFER_UNIT_US 10
|
|
|
|
#define REBOOT_COMMAND 0xbb
|
|
|
|
#define TS_COMPOSITE_ENABLE 1
|
|
#define TS_COMPOSITE_DISABLE 2
|
|
#define TS_COMPOSITE_READ 3
|
|
|
|
#define TS_TRIGGER_SCOPE_ENABLE 4
|
|
#define TS_TRIGGER_SCOPE_DISABLE 5
|
|
#define TS_TRIGGER_SCOPE_READ 6
|
|
|
|
#define PROTOCOL_MSG "msg"
|
|
#define PROTOCOL_HELLO_PREFIX "***"
|
|
|
|
#define TS_RESPONSE_UNDERRUN 0x80
|
|
#define TS_RESPONSE_OVERRUN 0x81
|
|
#define TS_RESPONSE_CRC_FAILURE 0x82
|
|
#define TS_RESPONSE_UNRECOGNIZED_COMMAND 0x83
|
|
#define TS_RESPONSE_OUT_OF_RANGE 0x84
|
|
#define TS_RESPONSE_FRAMING_ERROR 0x8D
|
|
! 0x52 82
|
|
#define TS_READ_COMMAND 'R'
|
|
! 0x47
|
|
#define TS_GET_TEXT 'G'
|
|
! 0x45
|
|
#define TS_EXECUTE 'E'
|
|
#define TS_ONLINE_PROTOCOL 'z'
|
|
! 0x34
|
|
#define TS_GET_OUTPUTS_SIZE '4'
|
|
#define TS_GET_COMPOSITE_BUFFER_DONE_DIFFERENTLY '8'
|
|
#define TS_GET_SCATTERED_GET_COMMAND '9'
|
|
|
|
#define TS_QUERY_BOOTLOADER 'L'
|
|
|
|
#define TS_QUERY_BOOTLOADER_NONE 0
|
|
#define TS_QUERY_BOOTLOADER_OPENBLT 1
|
|
|
|
! Performance tracing
|
|
#define TS_PERF_TRACE_BEGIN '_'
|
|
#define TS_PERF_TRACE_GET_BUFFER 'b'
|
|
|
|
! knock analyzer
|
|
#define TS_KNOCK_SPECTROGRAM_ENABLE 'm'
|
|
#define TS_KNOCK_SPECTROGRAM_DISABLE 'n'
|
|
! 0x57 pageValueWrite
|
|
#define TS_SINGLE_WRITE_COMMAND 'W'
|
|
! 0x43 pageChunkWrite
|
|
#define TS_CHUNK_WRITE_COMMAND 'C'
|
|
|
|
! These commands are used exclusively by the rusEFI console
|
|
! 0x74
|
|
#define TS_TEST_COMMAND 't'
|
|
|
|
! High speed logger commands
|
|
#define TS_SET_LOGGER_SWITCH 'l'
|
|
|
|
|
|
|
|
#define CMD_SET_SENSOR_MOCK "set_sensor_mock"
|
|
#define CMD_RESET_SENSOR_MOCKS "reset_sensor_mocks"
|
|
#define CMD_RESET_SIMULATOR "reset_simulator"
|
|
#define CMD_SET "set"
|
|
#define CMD_GET "get"
|
|
#define CMD_ENGINESNIFFERRPMTHRESHOLD "engineSnifferRpmThreshold"
|
|
#define CMD_INDIVIDUAL_INJECTION "set_individual_coils_ignition"
|
|
#define CMD_MIL_BENCH "milbench"
|
|
#define CMD_FUEL_BENCH "fuelbench"
|
|
#define CMD_FUEL_PUMP_BENCH "fuelpumpbench"
|
|
#define CMD_IDLE_BENCH "idlebench"
|
|
#define CMD_SPARK_BENCH "sparkbench"
|
|
#define CMD_STARTER_BENCH "starterbench"
|
|
#define CMD_HPFP_BENCH "hpfpbench"
|
|
#define CMD_AC_RELAY_BENCH "acrelaybench"
|
|
#define CMD_FAN_BENCH "fanbench"
|
|
#define CMD_FAN2_BENCH "fan2bench"
|
|
#define CMD_PINS "pins"
|
|
#define CMD_ETB_DUTY "set_etb_duty"
|
|
#define CMD_SELF_STIMULATION "self_stimulation"
|
|
#define CMD_EXTERNAL_STIMULATION "ext_stimulation"
|
|
#define CMD_RPM "rpm"
|
|
#define CMD_VSS_PIN "vss_pin"
|
|
#define CMD_TRIGGER_PIN "set_trigger_input_pin"
|
|
#define CMD_LOGIC_PIN "set_logic_input_pin"
|
|
#define CMD_ALTERNATOR_PIN "set_alternator_pin"
|
|
#define CMD_IDLE_PIN "set_idle_pin"
|
|
#define CMD_BOOST_PIN "set_boost_pin"
|
|
#define CMD_TRIGGER_SIMULATOR_PIN "set_trigger_simulator_pin"
|
|
#define CMD_IGNITION_PIN "set_ignition_pin"
|
|
#define CMD_INJECTION_PIN "set_injection_pin"
|
|
|
|
#define CMD_RESET_ENGINE_SNIFFER "reset_engine_chart"
|
|
#define CMD_FUNCTIONAL_TEST_MODE "test_mode"
|
|
|
|
#define CMD_ECU_UNLOCK "unlock"
|
|
#define CMD_ENGINE_TYPE "engine_type"
|
|
#define CMD_INJECTION "injection"
|
|
#define CMD_IGNITION "ignition"
|
|
#define CMD_PWM "pwm"
|
|
#define CMD_TRIGGERINFO "triggerinfo"
|
|
#define CMD_WRITECONFIG "writeconfig"
|
|
#define CMD_BURNCONFIG "burnconfig"
|
|
#define CMD_DATE "date"
|
|
#define CMD_REBOOT "reboot"
|
|
#define CMD_REBOOT_DFU "reboot_dfu"
|
|
#define CMD_REBOOT_OPENBLT "reboot_openblt"
|
|
#define CMD_ENABLE "enable"
|
|
#define CMD_DISABLE "disable"
|
|
#define CMD_TRIGGER_HW_INPUT "trigger_hw_input"
|
|
|
|
|
|
#define PROTOCOL_OUTPIN "outpin"
|
|
#define PROTOCOL_ANALOG_CHART "analog_chart"
|
|
#define PROTOCOL_ENGINE_SNIFFER "wave_chart"
|
|
#define PROTOCOL_KNOCK_SPECTROGRAMM "knock_spectrogram"
|
|
#define PROTOCOL_VERSION_TAG "rusEfiVersion"
|
|
#define PROTOCOL_TEST_RESPONSE_TAG "ts_p_alive"
|
|
#define PROTOCOL_SIGNATURE_PREFIX "rusEFI "
|
|
#define FRONTEND_TITLE_BAR_NAME "rusEFI"
|
|
|
|
! Engine Sniffer Protocol
|
|
#define PROTOCOL_ES_DOWN "d"
|
|
#define PROTOCOL_ES_UP "u"
|
|
#define TOP_DEAD_CENTER_MESSAGE "r"
|
|
|
|
! Engine Sniffer channel names
|
|
#define PROTOCOL_CRANK1 "t1"
|
|
#define PROTOCOL_CRANK2 "t2"
|
|
|
|
#define PROTOCOL_VVT1_NAME "VVT1"
|
|
#define PROTOCOL_VVT2_NAME "VVT2"
|
|
#define PROTOCOL_VVT3_NAME "VVT3"
|
|
#define PROTOCOL_VVT4_NAME "VVT4"
|
|
#define PROTOCOL_HIP_NAME "HIP"
|
|
#define PROTOCOL_TACH_NAME "tach"
|
|
#define PROTOCOL_HPFP_NAME "hpfp"
|
|
#define PROTOCOL_ACR_NAME "acr"
|
|
|
|
#define PROTOCOL_WA_CHANNEL_1 "input1"
|
|
#define PROTOCOL_WA_CHANNEL_2 "input2"
|
|
#define PROTOCOL_WA_CHANNEL_3 "input3"
|
|
#define PROTOCOL_WA_CHANNEL_4 "input4"
|
|
|
|
#define MLQ_HEADER_SIZE 24
|
|
#define MLQ_FIELD_HEADER_SIZE 89
|
|
|
|
! TEST_CONTROL_MAGIC_WORD copy-paste while we are learning how to share between rusEFI and stim firmware
|
|
#define CAN_BENCH_HEADER2 0x66
|
|
|
|
#define BENCH_FUEL_PUMP_DURATION 3000
|
|
#define BENCH_FAN_DURATION 2000
|
|
#define BENCH_VVT_DURATION 300
|
|
#define BENCH_MAIN_RELAY_DURATION 1000
|
|
#define BENCH_STARTER_DURATION 4000
|
|
#define BENCH_AC_RELAY_DURATION 800
|
|
|
|
#define DEFAULT_SELT_STIM_RPM 1200
|
|
#define DEFAULT_SELT_STIM_VVT0 23
|