107 lines
3.3 KiB
Plaintext
107 lines
3.3 KiB
Plaintext
avrisp.name=AVR ISP
|
|
avrisp.communication=serial
|
|
avrisp.protocol=stk500v1
|
|
avrisp.program.protocol=stk500v1
|
|
avrisp.program.tool=avrdude
|
|
avrisp.program.extra_params=-P{serial.port}
|
|
|
|
avrispmkii.name=AVRISP mkII
|
|
avrispmkii.communication=usb
|
|
avrispmkii.protocol=stk500v2
|
|
avrispmkii.program.protocol=stk500v2
|
|
avrispmkii.program.tool=avrdude
|
|
avrispmkii.program.extra_params=-Pusb
|
|
|
|
usbtinyisp.name=USBtinyISP
|
|
usbtinyisp.protocol=usbtiny
|
|
usbtinyisp.program.tool=avrdude
|
|
usbtinyisp.program.extra_params=
|
|
|
|
arduinoisp.name=ArduinoISP
|
|
arduinoisp.protocol=arduinoisp
|
|
arduinoisp.program.tool=avrdude
|
|
arduinoisp.program.extra_params=
|
|
|
|
arduinoisporg.name=ArduinoISP.org
|
|
arduinoisporg.protocol=arduinoisporg
|
|
arduinoisporg.program.tool=avrdude
|
|
arduinoisporg.program.extra_params=
|
|
|
|
usbasp.name=USBasp
|
|
usbasp.communication=usb
|
|
usbasp.protocol=usbasp
|
|
usbasp.program.protocol=usbasp
|
|
usbasp.program.tool=avrdude
|
|
usbasp.program.extra_params=-Pusb
|
|
|
|
parallel.name=Parallel Programmer
|
|
parallel.protocol=dapa
|
|
parallel.force=true
|
|
# parallel.delay=200
|
|
parallel.program.tool=avrdude
|
|
parallel.program.extra_params=-F
|
|
|
|
arduinoasisp.name=Arduino as ISP
|
|
arduinoasisp.communication=serial
|
|
arduinoasisp.protocol=arduino
|
|
arduinoasisp.speed=19200
|
|
arduinoasisp.program.protocol=arduino
|
|
arduinoasisp.program.speed=19200
|
|
arduinoasisp.program.tool=avrdude
|
|
arduinoasisp.program.extra_params=-P{serial.port} -b{program.speed}
|
|
|
|
usbGemma.name=Arduino Gemma
|
|
usbGemma.protocol=arduinogemma
|
|
usbGemma.program.tool=avrdude
|
|
usbGemma.program.extra_params=
|
|
usbGemma.config.path={runtime.platform.path}/bootloaders/gemma/avrdude.conf
|
|
|
|
## Notes about Dangerous Prototypes Bus Pirate as ISP
|
|
## Bus Pirate V3 need Firmware v5.10 or later
|
|
## Bus Pirate V4 need Firmware v6.3-r2151 or later
|
|
## Could happen that BP does not have enough current to power an Arduino board
|
|
## through the ICSP connector. In this case disconnect the +Vcc from ICSP connector
|
|
## and power Arduino board in the normal way.
|
|
buspirate.name=BusPirate as ISP
|
|
buspirate.communication=serial
|
|
buspirate.protocol=buspirate
|
|
buspirate.program.protocol=buspirate
|
|
buspirate.program.tool=avrdude
|
|
buspirate.program.extra_params=-P{serial.port}
|
|
|
|
# STK500 firmware version v1 and v2 use different serial protocols.
|
|
# Using the 'stk500' protocol tells avrdude to try and autodetect the
|
|
# firmware version. If this leads to problems, we might need to add
|
|
# stk500v1 and stk500v2 entries to allow explicitely selecting the
|
|
# firmware version.
|
|
stk500.name=Atmel STK500 development board
|
|
stk500.communication=serial
|
|
stk500.protocol=stk500
|
|
stk500.program.protocol=stk500
|
|
stk500.program.tool=avrdude
|
|
stk500.program.extra_params=-P{serial.port}
|
|
|
|
jtag3isp.name=Atmel JTAGICE3 (ISP mode)
|
|
jtag3isp.communication=usb
|
|
jtag3isp.protocol=jtag3isp
|
|
jtag3isp.program.protocol=jtag3isp
|
|
jtag3isp.program.tool=avrdude
|
|
jtag3isp.program.extra_params=
|
|
|
|
jtag3.name=Atmel JTAGICE3 (JTAG mode)
|
|
jtag3.communication=usb
|
|
jtag3.protocol=jtag3
|
|
jtag3.program.protocol=jtag3
|
|
jtag3.program.tool=avrdude
|
|
# Set a bitclock of 0.1us (the fastest supported value). This should
|
|
# work regardless of the crystal used, since JTAG doesn't use the MCU
|
|
# clock but dictates its own clock.
|
|
jtag3.program.extra_params=-B0.1
|
|
|
|
atmel_ice.name=Atmel-ICE (AVR)
|
|
atmel_ice.communication=usb
|
|
atmel_ice.protocol=atmelice_isp
|
|
atmel_ice.program.protocol=atmelice_isp
|
|
atmel_ice.program.tool=avrdude
|
|
atmel_ice.program.extra_params=-Pusb
|