2015-04-07 03:57:51 -07:00
|
|
|
#include "LiquidCrystal.h"
|
|
|
|
|
|
|
|
#include <stdio.h>
|
|
|
|
#include <string.h>
|
|
|
|
#include <WProgram.h>
|
|
|
|
|
|
|
|
// When the display powers up, it is configured as follows:
|
|
|
|
//
|
|
|
|
// 1. Display clear
|
|
|
|
// 2. Function set:
|
|
|
|
// DL = 1; 8-bit interface data
|
|
|
|
// N = 0; 1-line display
|
|
|
|
// F = 0; 5x8 dot character font
|
|
|
|
// 3. Display on/off control:
|
|
|
|
// D = 0; Display off
|
|
|
|
// C = 0; Cursor off
|
|
|
|
// B = 0; Blinking off
|
|
|
|
// 4. Entry mode set:
|
|
|
|
// I/D = 1; Increment by 1
|
|
|
|
// S = 0; No shift
|
|
|
|
//
|
|
|
|
// Note, however, that resetting the Arduino doesn't reset the LCD, so we
|
|
|
|
// can't assume that its in that state when a sketch starts (and the
|
|
|
|
// LiquidCrystal constructor is called).
|
|
|
|
|
|
|
|
// This library has been modified to be compatible with the LeafLabs Maple;
|
|
|
|
// very conservative timing is used due to problems with delayMicroseconds()
|
|
|
|
// that should be fixed in the 0.0.7 release of the libmaple. [bnewbold]
|
|
|
|
|
|
|
|
LiquidCrystal::LiquidCrystal(uint8 rs, uint8 rw, uint8 enable,
|
|
|
|
uint8 d0, uint8 d1, uint8 d2, uint8 d3,
|
|
|
|
uint8 d4, uint8 d5, uint8 d6, uint8 d7)
|
|
|
|
{
|
|
|
|
init(0, rs, rw, enable, d0, d1, d2, d3, d4, d5, d6, d7);
|
|
|
|
}
|
|
|
|
|
|
|
|
LiquidCrystal::LiquidCrystal(uint8 rs, uint8 enable,
|
|
|
|
uint8 d0, uint8 d1, uint8 d2, uint8 d3,
|
|
|
|
uint8 d4, uint8 d5, uint8 d6, uint8 d7)
|
|
|
|
{
|
|
|
|
init(0, rs, 255, enable, d0, d1, d2, d3, d4, d5, d6, d7);
|
|
|
|
}
|
|
|
|
|
|
|
|
LiquidCrystal::LiquidCrystal(uint8 rs, uint8 rw, uint8 enable,
|
|
|
|
uint8 d0, uint8 d1, uint8 d2, uint8 d3)
|
|
|
|
{
|
|
|
|
init(1, rs, rw, enable, d0, d1, d2, d3, 0, 0, 0, 0);
|
|
|
|
}
|
|
|
|
|
|
|
|
LiquidCrystal::LiquidCrystal(uint8 rs, uint8 enable,
|
|
|
|
uint8 d0, uint8 d1, uint8 d2, uint8 d3)
|
|
|
|
{
|
|
|
|
init(1, rs, 255, enable, d0, d1, d2, d3, 0, 0, 0, 0);
|
|
|
|
}
|
|
|
|
|
|
|
|
void LiquidCrystal::init(uint8 fourbitmode, uint8 rs, uint8 rw, uint8 enable,
|
|
|
|
uint8 d0, uint8 d1, uint8 d2, uint8 d3,
|
|
|
|
uint8 d4, uint8 d5, uint8 d6, uint8 d7)
|
|
|
|
{
|
|
|
|
_rs_pin = rs;
|
|
|
|
_rw_pin = rw;
|
|
|
|
_enable_pin = enable;
|
|
|
|
|
|
|
|
_data_pins[0] = d0;
|
|
|
|
_data_pins[1] = d1;
|
|
|
|
_data_pins[2] = d2;
|
|
|
|
_data_pins[3] = d3;
|
|
|
|
_data_pins[4] = d4;
|
|
|
|
_data_pins[5] = d5;
|
|
|
|
_data_pins[6] = d6;
|
|
|
|
_data_pins[7] = d7;
|
|
|
|
displaymode=fourbitmode;
|
|
|
|
|
|
|
|
if (fourbitmode)
|
|
|
|
_displayfunction = LCD_4BITMODE | LCD_1LINE | LCD_5x8DOTS;
|
|
|
|
else
|
|
|
|
_displayfunction = LCD_8BITMODE | LCD_1LINE | LCD_5x8DOTS;
|
|
|
|
|
|
|
|
// TODO: bnewbold, re-enable this?
|
|
|
|
// begin(16, 1);
|
|
|
|
}
|
|
|
|
|
|
|
|
void LiquidCrystal::begin(uint8 cols, uint8 lines, uint8 dotsize) {
|
|
|
|
|
|
|
|
for (int i = 0; i < 8 - displaymode * 4; i++) {
|
|
|
|
//for (int i = 0; i <4; i++) {
|
|
|
|
pinMode(_data_pins[i], OUTPUT);
|
|
|
|
}
|
|
|
|
|
|
|
|
pinMode(_rs_pin, OUTPUT);
|
|
|
|
// we can save 1 pin by not using RW. Indicate by passing 255 instead of pin#
|
|
|
|
if (_rw_pin != 255) {
|
|
|
|
pinMode(_rw_pin, OUTPUT);
|
|
|
|
}
|
|
|
|
pinMode(_enable_pin, OUTPUT);
|
|
|
|
if (lines > 1) {
|
|
|
|
_displayfunction |= LCD_2LINE;
|
|
|
|
}
|
|
|
|
_numlines = lines;
|
|
|
|
_currline = 0;
|
|
|
|
|
|
|
|
// for some 1 line displays you can select a 10 pixel high font
|
|
|
|
if ((dotsize != 0) && (lines == 1)) {
|
|
|
|
_displayfunction |= LCD_5x10DOTS;
|
|
|
|
}
|
|
|
|
|
|
|
|
// SEE PAGE 45/46 FOR INITIALIZATION SPECIFICATION! according to
|
|
|
|
// datasheet, we need at least 40ms after power rises above 2.7V
|
|
|
|
// before sending commands. Arduino can turn on way befer 4.5V so
|
|
|
|
// we'll wait 50
|
|
|
|
delay(50); // Maple mod
|
|
|
|
//delayMicroseconds(50000);
|
|
|
|
// Now we pull both RS and R/W low to begin commands
|
|
|
|
digitalWrite(_rs_pin, LOW);
|
|
|
|
digitalWrite(_enable_pin, LOW);
|
|
|
|
if (_rw_pin != 255) {
|
|
|
|
digitalWrite(_rw_pin, LOW);
|
|
|
|
}
|
|
|
|
|
|
|
|
//put the LCD into 4 bit or 8 bit mode
|
|
|
|
if (! (_displayfunction & LCD_8BITMODE)) {
|
|
|
|
// this is according to the hitachi HD44780 datasheet
|
|
|
|
// figure 24, pg 46
|
|
|
|
|
|
|
|
// we start in 8bit mode, try to set 4 bit mode
|
|
|
|
write4bits(0x03);
|
|
|
|
delay(5); // Maple mod
|
|
|
|
//delayMicroseconds(4500); // wait min 4.1ms
|
|
|
|
|
|
|
|
// second try
|
|
|
|
write4bits(0x03);
|
|
|
|
delay(5); // Maple mod
|
|
|
|
//delayMicroseconds(4500); // wait min 4.1ms
|
|
|
|
|
|
|
|
// third go!
|
|
|
|
write4bits(0x03);
|
|
|
|
delay(1); // Maple mod
|
|
|
|
//delayMicroseconds(150);
|
|
|
|
|
|
|
|
// finally, set to 8-bit interface
|
|
|
|
write4bits(0x02);
|
|
|
|
} else {
|
|
|
|
// this is according to the hitachi HD44780 datasheet
|
|
|
|
// page 45 figure 23
|
|
|
|
|
|
|
|
// Send function set command sequence
|
|
|
|
command(LCD_FUNCTIONSET | _displayfunction);
|
|
|
|
delay(5); // Maple mod
|
|
|
|
//delayMicroseconds(4500); // wait more than 4.1ms
|
|
|
|
|
|
|
|
// second try
|
|
|
|
command(LCD_FUNCTIONSET | _displayfunction);
|
|
|
|
delay(1); // Maple mod
|
|
|
|
//delayMicroseconds(150);
|
|
|
|
|
|
|
|
// third go
|
|
|
|
command(LCD_FUNCTIONSET | _displayfunction);
|
|
|
|
}
|
|
|
|
|
|
|
|
// finally, set # lines, font size, etc.
|
|
|
|
command(LCD_FUNCTIONSET | _displayfunction);
|
|
|
|
|
|
|
|
// turn the display on with no cursor or blinking default
|
|
|
|
_displaycontrol = LCD_DISPLAYON | LCD_CURSOROFF | LCD_BLINKOFF;
|
|
|
|
display();
|
|
|
|
|
|
|
|
// clear it off
|
|
|
|
clear();
|
|
|
|
|
|
|
|
// Initialize to default text direction (for romance languages)
|
|
|
|
_displaymode = LCD_ENTRYLEFT | LCD_ENTRYSHIFTDECREMENT;
|
|
|
|
// set the entry mode
|
|
|
|
command(LCD_ENTRYMODESET | _displaymode);
|
|
|
|
|
|
|
|
}
|
|
|
|
|
|
|
|
/********** high level commands, for the user! */
|
|
|
|
void LiquidCrystal::clear()
|
|
|
|
{
|
|
|
|
command(LCD_CLEARDISPLAY); // clear display, set cursor position to zero
|
|
|
|
delay(2); // Maple mod
|
|
|
|
//delayMicroseconds(2000); // this command takes a long time!
|
|
|
|
}
|
|
|
|
|
|
|
|
void LiquidCrystal::home()
|
|
|
|
{
|
|
|
|
command(LCD_RETURNHOME); // set cursor position to zero
|
|
|
|
delay(2); // Maple mod
|
|
|
|
//delayMicroseconds(2000); // this command takes a long time!
|
|
|
|
}
|
|
|
|
|
|
|
|
void LiquidCrystal::setCursor(uint8 col, uint8 row)
|
|
|
|
{
|
|
|
|
int row_offsets[] = { 0x00, 0x40, 0x14, 0x54 };
|
|
|
|
if ( row > _numlines ) {
|
|
|
|
row = _numlines-1; // we count rows starting w/0
|
|
|
|
}
|
|
|
|
|
|
|
|
command(LCD_SETDDRAMADDR | (col + row_offsets[row]));
|
|
|
|
}
|
|
|
|
|
|
|
|
// Turn the display on/off (quickly)
|
|
|
|
void LiquidCrystal::noDisplay() {
|
|
|
|
_displaycontrol &= ~LCD_DISPLAYON;
|
|
|
|
command(LCD_DISPLAYCONTROL | _displaycontrol);
|
|
|
|
}
|
|
|
|
void LiquidCrystal::display() {
|
|
|
|
_displaycontrol |= LCD_DISPLAYON;
|
|
|
|
command(LCD_DISPLAYCONTROL | _displaycontrol);
|
|
|
|
}
|
|
|
|
|
|
|
|
// Turns the underline cursor on/off
|
|
|
|
void LiquidCrystal::noCursor() {
|
|
|
|
_displaycontrol &= ~LCD_CURSORON;
|
|
|
|
command(LCD_DISPLAYCONTROL | _displaycontrol);
|
|
|
|
}
|
|
|
|
void LiquidCrystal::cursor() {
|
|
|
|
_displaycontrol |= LCD_CURSORON;
|
|
|
|
command(LCD_DISPLAYCONTROL | _displaycontrol);
|
|
|
|
}
|
|
|
|
|
|
|
|
// Turn on and off the blinking cursor
|
|
|
|
void LiquidCrystal::noBlink() {
|
|
|
|
_displaycontrol &= ~LCD_BLINKON;
|
|
|
|
command(LCD_DISPLAYCONTROL | _displaycontrol);
|
|
|
|
}
|
|
|
|
void LiquidCrystal::blink() {
|
|
|
|
_displaycontrol |= LCD_BLINKON;
|
|
|
|
command(LCD_DISPLAYCONTROL | _displaycontrol);
|
|
|
|
}
|
|
|
|
|
|
|
|
// These commands scroll the display without changing the RAM
|
|
|
|
void LiquidCrystal::scrollDisplayLeft(void) {
|
|
|
|
command(LCD_CURSORSHIFT | LCD_DISPLAYMOVE | LCD_MOVELEFT);
|
|
|
|
}
|
|
|
|
void LiquidCrystal::scrollDisplayRight(void) {
|
|
|
|
command(LCD_CURSORSHIFT | LCD_DISPLAYMOVE | LCD_MOVERIGHT);
|
|
|
|
}
|
|
|
|
|
|
|
|
// This is for text that flows Left to Right
|
|
|
|
void LiquidCrystal::leftToRight(void) {
|
|
|
|
_displaymode |= LCD_ENTRYLEFT;
|
|
|
|
command(LCD_ENTRYMODESET | _displaymode);
|
|
|
|
}
|
|
|
|
|
|
|
|
// This is for text that flows Right to Left
|
|
|
|
void LiquidCrystal::rightToLeft(void) {
|
|
|
|
_displaymode &= ~LCD_ENTRYLEFT;
|
|
|
|
command(LCD_ENTRYMODESET | _displaymode);
|
|
|
|
}
|
|
|
|
|
|
|
|
// This will 'right justify' text from the cursor
|
|
|
|
void LiquidCrystal::autoscroll(void) {
|
|
|
|
_displaymode |= LCD_ENTRYSHIFTINCREMENT;
|
|
|
|
command(LCD_ENTRYMODESET | _displaymode);
|
|
|
|
}
|
|
|
|
|
|
|
|
// This will 'left justify' text from the cursor
|
|
|
|
void LiquidCrystal::noAutoscroll(void) {
|
|
|
|
_displaymode &= ~LCD_ENTRYSHIFTINCREMENT;
|
|
|
|
command(LCD_ENTRYMODESET | _displaymode);
|
|
|
|
}
|
|
|
|
|
|
|
|
// Allows us to fill the first 8 CGRAM locations
|
|
|
|
// with custom characters
|
|
|
|
void LiquidCrystal::createChar(uint8 location, uint8 charmap[]) {
|
|
|
|
location &= 0x7; // we only have 8 locations 0-7
|
|
|
|
command(LCD_SETCGRAMADDR | (location << 3));
|
|
|
|
for (int i=0; i<8; i++) {
|
|
|
|
write(charmap[i]);
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
/*********** mid level commands, for sending data/cmds */
|
|
|
|
|
|
|
|
inline void LiquidCrystal::command(uint8 value) {
|
|
|
|
send(value, LOW);
|
|
|
|
}
|
|
|
|
|
|
|
|
inline size_t LiquidCrystal::write(uint8 value) {
|
|
|
|
send(value, HIGH);
|
|
|
|
return 1;
|
|
|
|
}
|
|
|
|
|
|
|
|
/************ low level data pushing commands **********/
|
|
|
|
|
|
|
|
// write either command or data, with automatic 4/8-bit selection
|
|
|
|
void LiquidCrystal::send(uint8 value, uint8 mode) {
|
|
|
|
digitalWrite(_rs_pin, mode);
|
|
|
|
|
|
|
|
// if there is a RW pin indicated, set it low to Write
|
|
|
|
if (_rw_pin != 255) {
|
|
|
|
digitalWrite(_rw_pin, LOW);
|
|
|
|
}
|
|
|
|
|
|
|
|
if (_displayfunction & LCD_8BITMODE) {
|
|
|
|
write8bits(value);
|
|
|
|
} else {
|
|
|
|
write4bits(value>>4);
|
|
|
|
write4bits(value);
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
void LiquidCrystal::pulseEnable(void) {
|
|
|
|
// _enable_pin should already be LOW (unless someone else messed
|
|
|
|
// with it), so don't sit around waiting for long.
|
|
|
|
digitalWrite(_enable_pin, LOW);
|
|
|
|
delayMicroseconds(1);
|
|
|
|
|
|
|
|
// Enable pulse must be > 450 ns. Value chosen here according to
|
|
|
|
// the following threads:
|
|
|
|
// http://forums.leaflabs.com/topic.php?id=640
|
|
|
|
// http://forums.leaflabs.com/topic.php?id=512
|
|
|
|
gpio_toggle_bit(PIN_MAP[_enable_pin].gpio_device, PIN_MAP[_enable_pin].gpio_bit);// togglePin(_enable_pin);
|
|
|
|
delayMicroseconds(1);
|
|
|
|
gpio_toggle_bit(PIN_MAP[_enable_pin].gpio_device, PIN_MAP[_enable_pin].gpio_bit);// togglePin(_enable_pin);
|
|
|
|
|
|
|
|
// Commands needs > 37us to settle.
|
|
|
|
delayMicroseconds(42);
|
|
|
|
}
|
|
|
|
|
|
|
|
void LiquidCrystal::write4bits(uint8 value) {
|
|
|
|
for (int i = 0; i < 4; i++) {
|
|
|
|
digitalWrite(_data_pins[i], (value >> i) & 0x01);
|
|
|
|
}
|
|
|
|
|
|
|
|
pulseEnable();
|
|
|
|
}
|
|
|
|
|
|
|
|
void LiquidCrystal::write8bits(uint8 value) {
|
|
|
|
for (int i = 0; i < 8; i++) {
|
|
|
|
digitalWrite(_data_pins[i], (value >> i) & 0x01);
|
|
|
|
}
|
|
|
|
|
|
|
|
pulseEnable();
|
|
|
|
}
|