diff --git a/STM32F1/libraries/SPI/examples/using_SPI_ports/using_SPI_ports.ino b/STM32F1/libraries/SPI/examples/using_SPI_ports/using_SPI_ports.ino
new file mode 100644
index 0000000..b8ebea4
--- /dev/null
+++ b/STM32F1/libraries/SPI/examples/using_SPI_ports/using_SPI_ports.ino
@@ -0,0 +1,64 @@
+/**
+    SPI_1 and SPI_2 port example code
+    
+    Description:
+    This sketch sends one byte with value 0x55 over the SPI_1 or SPI_2 port.
+    The received byte (the answer from the SPI slave device) is stored to the <data> variable.
+    
+    The sketch as it is, works with SPI_1 port. For using the SPI_2 port, just
+    un-comment all the nessesary code lines marked with <SPI_2> word.
+    
+    Created on 10 Jun 2015 by Vassilis Serasidis
+    email:  avrsite@yahoo.gr
+    
+    Using the first SPI port (SPI_1)
+    SS    <-->  PA4 <-->  BOARD_SPI1_NSS_PIN
+    SCK   <-->  PA5 <-->  BOARD_SPI1_SCK_PIN
+    MISO  <-->  PA6 <-->  BOARD_SPI1_MISO_PIN
+    MOSI  <-->  PA7 <-->  BOARD_SPI1_MOSI_PIN
+    
+    Using the second SPI port (SPI_2)
+    SS    <-->  PB12 <-->  BOARD_SPI2_NSS_PIN
+    SCK   <-->  PB13 <-->  BOARD_SPI2_SCK_PIN
+    MISO  <-->  PB14 <-->  BOARD_SPI2_MISO_PIN
+    MOSI  <-->  PB15 <-->  BOARD_SPI2_MOSI_PIN
+*/
+
+
+#include <SPI.h>
+
+#define SPI1_NSS_PIN PA4    //SPI_1 Chip Select pin is PA4. You can change it to the STM32 pin you want.
+#define SPI2_NSS_PIN PB12   //SPI_2 Chip Select pin is PB12. You can change it to the STM32 pin you want.
+
+//SPIClass SPI_2(2); //un-comment this line in case you want to use the SPI_2 port. 
+byte data;
+
+void setup() {
+  SPI.begin(); //Initialize the SPI_1 port.
+  //SPI_2.begin(); //Initialize the SPI_2 port.
+  
+  SPI.setBitOrder(MSBFIRST); // Set the SPI_1 bit order
+  //SPI_2.setBitOrder(MSBFIRST); // Set the SPI_2 bit order
+  
+  SPI.setDataMode(SPI_MODE0); //Set the  SPI_2 data mode 0
+  //SPI_2.setDataMode(SPI_MODE0); //Set the  SPI_2 data mode 0
+  
+  SPI.setClockDivider(SPI_CLOCK_DIV16);      // Slow speed (72 / 16 = 4.5 MHz SPI_1 speed)
+  //SPI_2.setClockDivider(SPI_CLOCK_DIV16);  // Slow speed (72 / 16 = 4.5 MHz SPI_2 speed) 
+
+  pinMode(SPI1_NSS_PIN, OUTPUT); // note: this must be after the SPI.begin() for gpio control of CSN
+  //pinMode(SPI2_NSS_PIN, OUTPUT); // note: this must be after the SPI_2.begin() for gpio control of CSN
+}
+
+void loop() {
+  digitalWrite(SPI1_NSS_PIN, LOW); // manually take CSN low for SPI_1 transmission
+  //digitalWrite(SPI2_NSS_PIN, LOW); // manually take CSN low for SPI_2 transmission
+  
+  data = SPI.transfer(0x55); //Send the HEX data 0x55 over SPI-1 port and store the received byte to the <data> variable.
+  //data = SPI_2.transfer(0x55); //Send the HEX data 0x55 over SPI-2 port and store the received byte to the <data> variable.
+  
+  digitalWrite(SPI1_NSS_PIN, HIGH); // manually take CSN high between spi transmissions
+  //digitalWrite(SPI2_NSS_PIN, HIGH); // manually take CSN high between spi transmissions
+
+  delayMicroseconds(10);    //Delay 10 micro seconds.
+}