124 lines
3.6 KiB
C++
124 lines
3.6 KiB
C++
/*
|
|
Web Server
|
|
|
|
A simple web server that shows the value of the analog input pins.
|
|
using an Arduino Wiznet Ethernet shield.
|
|
|
|
Circuit:
|
|
* Ethernet shield attached to pins 10, 11, 12, 13
|
|
* Analog inputs attached to pins A0 through A5 (optional)
|
|
|
|
created 18 Dec 2009
|
|
by David A. Mellis
|
|
modified 9 Apr 2012
|
|
by Tom Igoe
|
|
modified 12 Aug 2013
|
|
by Soohwan Kim
|
|
Modified 18 Aug 2015
|
|
by Vassilis Serasidis
|
|
|
|
=========================================================
|
|
Ported to STM32F103 on 18 Aug 2015 by Vassilis Serasidis
|
|
|
|
<---- Pinout ---->
|
|
W5x00 <--> STM32F103
|
|
SS <--> PA4 <--> BOARD_SPI1_NSS_PIN
|
|
SCK <--> PA5 <--> BOARD_SPI1_SCK_PIN
|
|
MISO <--> PA6 <--> BOARD_SPI1_MISO_PIN
|
|
MOSI <--> PA7 <--> BOARD_SPI1_MOSI_PIN
|
|
=========================================================
|
|
|
|
|
|
*/
|
|
|
|
#include <SPI.h>
|
|
#include <Ethernet_STM.h>
|
|
|
|
// Enter a MAC address and IP address for your controller below.
|
|
// The IP address will be dependent on your local network:
|
|
#if defined(WIZ550io_WITH_MACADDRESS) // Use assigned MAC address of WIZ550io
|
|
;
|
|
#else
|
|
byte mac[] = {0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED};
|
|
#endif
|
|
IPAddress ip(192,168,1,177);
|
|
|
|
// Initialize the Ethernet server library
|
|
// with the IP address and port you want to use
|
|
// (port 80 is default for HTTP):
|
|
EthernetServer server(80);
|
|
|
|
void setup() {
|
|
// Open serial communications and wait for port to open:
|
|
Serial.begin(9600);
|
|
while (!Serial) {
|
|
; // wait for serial port to connect. Needed for Leonardo only
|
|
}
|
|
|
|
|
|
// start the Ethernet connection and the server:
|
|
#if defined(WIZ550io_WITH_MACADDRESS)
|
|
Ethernet.begin(ip);
|
|
#else
|
|
Ethernet.begin(mac, ip);
|
|
#endif
|
|
server.begin();
|
|
Serial.print("server is at ");
|
|
Serial.println(Ethernet.localIP());
|
|
}
|
|
|
|
|
|
void loop() {
|
|
// listen for incoming clients
|
|
EthernetClient client = server.available();
|
|
if (client) {
|
|
Serial.println("new client");
|
|
// an http request ends with a blank line
|
|
boolean currentLineIsBlank = true;
|
|
while (client.connected()) {
|
|
if (client.available()) {
|
|
char c = client.read();
|
|
Serial.write(c);
|
|
// if you've gotten to the end of the line (received a newline
|
|
// character) and the line is blank, the http request has ended,
|
|
// so you can send a reply
|
|
if (c == '\n' && currentLineIsBlank) {
|
|
// send a standard http response header
|
|
client.println("HTTP/1.1 200 OK");
|
|
client.println("Content-Type: text/html");
|
|
client.println("Connection: close"); // the connection will be closed after completion of the response
|
|
client.println("Refresh: 5"); // refresh the page automatically every 5 sec
|
|
client.println();
|
|
client.println("<!DOCTYPE HTML>");
|
|
client.println("<html>");
|
|
// output the value of each analog input pin
|
|
for (int analogChannel = 0; analogChannel < 6; analogChannel++) {
|
|
int sensorReading = analogRead(analogChannel);
|
|
client.print("analog input ");
|
|
client.print(analogChannel);
|
|
client.print(" is ");
|
|
client.print(sensorReading);
|
|
client.println("<br />");
|
|
}
|
|
client.println("</html>");
|
|
break;
|
|
}
|
|
if (c == '\n') {
|
|
// you're starting a new line
|
|
currentLineIsBlank = true;
|
|
}
|
|
else if (c != '\r') {
|
|
// you've gotten a character on the current line
|
|
currentLineIsBlank = false;
|
|
}
|
|
}
|
|
}
|
|
// give the web browser time to receive the data
|
|
delay(1);
|
|
// close the connection:
|
|
client.stop();
|
|
Serial.println("client disonnected");
|
|
}
|
|
}
|
|
|