/* Speeduino - Simple engine management for the Arduino Mega 2560 platform Copyright (C) Josh Stewart A full copy of the license may be found in the projects root directory */ /* Returns how much free dynamic memory exists (between heap and stack) This function is one big MISRA violation. MISRA advisories forbid directly poking at memory addresses, however there is no other way of determining heap size on embedded systems. */ #include "utils.h" #include "globals.h" uint16_t freeRam () { #if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__) extern int __heap_start, *__brkval; uint16_t v; return (uint16_t) &v - (__brkval == 0 ? (int) &__heap_start : (int) __brkval); #elif defined(CORE_TEENSY) uint32_t stackTop; uint32_t heapTop; // current position of the stack. stackTop = (uint32_t) &stackTop; // current position of heap. void* hTop = malloc(1); heapTop = (uint32_t) hTop; free(hTop); // The difference is the free, available ram. return (uint16_t)stackTop - heapTop; #elif defined(CORE_STM32) char top = 't'; return &top - reinterpret_cast(sbrk(0)); #endif } //This function performs a translation between the pin list that appears in TS and the actual pin numbers //For the digital IO, this will simply return the same number as the rawPin value as those are mapped directly. //For analog pins, it will translate them into the currect internal pin number byte pinTranslate(byte rawPin) { byte outputPin = rawPin; if(rawPin > BOARD_DIGITAL_GPIO_PINS) { outputPin = A8 + (outputPin - BOARD_DIGITAL_GPIO_PINS - 1); } return outputPin; } void setResetControlPinState() { BIT_CLEAR(currentStatus.status3, BIT_STATUS3_RESET_PREVENT); /* Setup reset control initial state */ switch (resetControl) { case RESET_CONTROL_PREVENT_WHEN_RUNNING: /* Set the reset control pin LOW and change it to HIGH later when we get sync. */ digitalWrite(pinResetControl, LOW); BIT_CLEAR(currentStatus.status3, BIT_STATUS3_RESET_PREVENT); break; case RESET_CONTROL_PREVENT_ALWAYS: /* Set the reset control pin HIGH and never touch it again. */ digitalWrite(pinResetControl, HIGH); BIT_SET(currentStatus.status3, BIT_STATUS3_RESET_PREVENT); break; case RESET_CONTROL_SERIAL_COMMAND: /* Set the reset control pin HIGH. There currently isn't any practical difference between this and PREVENT_ALWAYS but it doesn't hurt anything to have them separate. */ digitalWrite(pinResetControl, HIGH); BIT_CLEAR(currentStatus.status3, BIT_STATUS3_RESET_PREVENT); break; } } void setPinMapping(byte boardID) { switch (boardID) { case 0: #ifndef SMALL_FLASH_MODE //No support for bluepill here anyway //Pin mappings as per the v0.1 shield pinInjector1 = 8; //Output pin injector 1 is on pinInjector2 = 9; //Output pin injector 2 is on pinInjector3 = 11; //Output pin injector 3 is on pinInjector4 = 10; //Output pin injector 4 is on pinInjector5 = 12; //Output pin injector 5 is on pinCoil1 = 6; //Pin for coil 1 pinCoil2 = 7; //Pin for coil 2 pinCoil3 = 12; //Pin for coil 3 pinCoil4 = 13; //Pin for coil 4 pinCoil5 = 14; //Pin for coil 5 pinTrigger = 2; //The CAS pin pinTrigger2 = 3; //The CAS pin pinTPS = A0; //TPS input pin pinMAP = A1; //MAP sensor pin pinIAT = A2; //IAT sensor pin pinCLT = A3; //CLS sensor pin pinO2 = A4; //O2 Sensor pin pinIdle1 = 46; //Single wire idle control pinIdle2 = 47; //2 wire idle control pinStepperDir = 16; //Direction pin for DRV8825 driver pinStepperStep = 17; //Step pin for DRV8825 driver pinFan = 47; //Pin for the fan output pinFuelPump = 4; //Fuel pump output pinTachOut = 49; //Tacho output pin pinFlex = 19; // Flex sensor (Must be external interrupt enabled) pinResetControl = 43; //Reset control output #endif break; case 1: #ifndef SMALL_FLASH_MODE //No support for bluepill here anyway //Pin mappings as per the v0.2 shield pinInjector1 = 8; //Output pin injector 1 is on pinInjector2 = 9; //Output pin injector 2 is on pinInjector3 = 10; //Output pin injector 3 is on pinInjector4 = 11; //Output pin injector 4 is on pinInjector5 = 12; //Output pin injector 5 is on pinCoil1 = 28; //Pin for coil 1 pinCoil2 = 24; //Pin for coil 2 pinCoil3 = 40; //Pin for coil 3 pinCoil4 = 36; //Pin for coil 4 pinCoil5 = 34; //Pin for coil 5 PLACEHOLDER value for now pinTrigger = 20; //The CAS pin pinTrigger2 = 21; //The Cam Sensor pin pinTPS = A2; //TPS input pin pinMAP = A3; //MAP sensor pin pinIAT = A0; //IAT sensor pin pinCLT = A1; //CLS sensor pin pinO2 = A8; //O2 Sensor pin pinBat = A4; //Battery reference voltage pin pinDisplayReset = 48; // OLED reset pin pinTachOut = 49; //Tacho output pin pinIdle1 = 30; //Single wire idle control pinIdle2 = 31; //2 wire idle control pinStepperDir = 16; //Direction pin for DRV8825 driver pinStepperStep = 17; //Step pin for DRV8825 driver pinFan = 47; //Pin for the fan output pinFuelPump = 4; //Fuel pump output pinFlex = 2; // Flex sensor (Must be external interrupt enabled) pinResetControl = 43; //Reset control output break; #endif case 2: #ifndef SMALL_FLASH_MODE //No support for bluepill here anyway //Pin mappings as per the v0.3 shield pinInjector1 = 8; //Output pin injector 1 is on pinInjector2 = 9; //Output pin injector 2 is on pinInjector3 = 10; //Output pin injector 3 is on pinInjector4 = 11; //Output pin injector 4 is on pinInjector5 = 12; //Output pin injector 5 is on pinCoil1 = 28; //Pin for coil 1 pinCoil2 = 24; //Pin for coil 2 pinCoil3 = 40; //Pin for coil 3 pinCoil4 = 36; //Pin for coil 4 pinCoil5 = 34; //Pin for coil 5 PLACEHOLDER value for now pinTrigger = 19; //The CAS pin pinTrigger2 = 18; //The Cam Sensor pin pinTPS = A2;//TPS input pin pinMAP = A3; //MAP sensor pin pinIAT = A0; //IAT sensor pin pinCLT = A1; //CLS sensor pin pinO2 = A8; //O2 Sensor pin pinBat = A4; //Battery reference voltage pin pinDisplayReset = 48; // OLED reset pin pinTachOut = 49; //Tacho output pin pinIdle1 = 5; //Single wire idle control pinIdle2 = 53; //2 wire idle control pinBoost = 7; //Boost control pinVVT_1 = 6; //Default VVT output pinFuelPump = 4; //Fuel pump output pinStepperDir = 16; //Direction pin for DRV8825 driver pinStepperStep = 17; //Step pin for DRV8825 driver pinStepperEnable = 26; //Enable pin for DRV8825 pinFan = A13; //Pin for the fan output pinLaunch = 51; //Can be overwritten below pinFlex = 2; // Flex sensor (Must be external interrupt enabled) pinResetControl = 50; //Reset control output #if defined(CORE_TEENSY) pinTrigger = 23; pinStepperDir = 33; pinStepperStep = 34; pinCoil1 = 31; pinTachOut = 28; pinFan = 27; pinCoil4 = 21; pinCoil3 = 30; pinO2 = A22; #endif #endif break; case 3: //Pin mappings as per the v0.4 shield pinInjector1 = 8; //Output pin injector 1 is on pinInjector2 = 9; //Output pin injector 2 is on pinInjector3 = 10; //Output pin injector 3 is on pinInjector4 = 11; //Output pin injector 4 is on pinInjector5 = 12; //Output pin injector 5 is on pinCoil1 = 40; //Pin for coil 1 pinCoil2 = 38; //Pin for coil 2 pinCoil3 = 52; //Pin for coil 3 pinCoil4 = 50; //Pin for coil 4 pinCoil5 = 34; //Pin for coil 5 PLACEHOLDER value for now pinTrigger = 19; //The CAS pin pinTrigger2 = 18; //The Cam Sensor pin pinTPS = A2;//TPS input pin pinMAP = A3; //MAP sensor pin pinIAT = A0; //IAT sensor pin pinCLT = A1; //CLS sensor pin pinO2 = A8; //O2 Sensor pin pinBat = A4; //Battery reference voltage pin pinDisplayReset = 48; // OLED reset pin pinTachOut = 49; //Tacho output pin (Goes to ULN2803) pinIdle1 = 5; //Single wire idle control pinIdle2 = 6; //2 wire idle control pinBoost = 7; //Boost control pinVVT_1 = 4; //Default VVT output pinFuelPump = 45; //Fuel pump output (Goes to ULN2803) pinStepperDir = 16; //Direction pin for DRV8825 driver pinStepperStep = 17; //Step pin for DRV8825 driver pinStepperEnable = 24; //Enable pin for DRV8825 pinFan = 47; //Pin for the fan output (Goes to ULN2803) pinLaunch = 51; //Can be overwritten below pinFlex = 2; // Flex sensor (Must be external interrupt enabled) pinResetControl = 43; //Reset control output #if defined(CORE_TEENSY) pinTrigger = 23; pinTrigger2 = 36; pinStepperDir = 34; pinStepperStep = 35; pinCoil1 = 31; pinTachOut = 28; pinFan = 27; pinCoil4 = 29; pinCoil3 = 30; pinO2 = A22; #elif defined(STM32F4) //Black F407VE http://wiki.stm32duino.com/index.php?title=STM32F407 //PC8~PC12 SDio //PA13~PA15 & PB4 SWD(debug) pins //PB0 EEPROM CS pin //PD5 & PD6 Serial2 pinInjector1 = PE7; //Output pin injector 1 is on pinInjector2 = PE8; //Output pin injector 2 is on pinInjector3 = PE9; //Output pin injector 3 is on pinInjector4 = PE10; //Output pin injector 4 is on pinInjector5 = PE11; //Output pin injector 5 is on pinCoil1 = PB5; //Pin for coil 1 pinCoil2 = PB6; //Pin for coil 2 pinCoil3 = PB7; //Pin for coil 3 pinCoil4 = PB8; //Pin for coil 4 pinCoil5 = PB9; //Pin for coil 5 pinTPS = A0; //TPS input pin pinMAP = A1; //MAP sensor pin pinIAT = A2; //IAT sensor pin pinCLT = A3; //CLT sensor pin pinO2 = A4; //O2 Sensor pin pinBat = A5; //Battery reference voltage pin pinBaro = A10; pinIdle1 = PB8; //Single wire idle control pinIdle2 = PB9; //2 wire idle control pinBoost = PE0; //Boost control pinVVT_1 = PE1; //Default VVT output pinStepperDir = PD8; //Direction pin for DRV8825 driver pinStepperStep = PB15; //Step pin for DRV8825 driver pinStepperEnable = PD9; //Enable pin for DRV8825 pinDisplayReset = PE1; // OLED reset pin pinFan = PE2; //Pin for the fan output pinFuelPump = PA6; //Fuel pump output pinTachOut = PA7; //Tacho output pin //external interrupt enabled pins //external interrupts could be enalbed in any pin, except same port numbers (PA4,PE4) pinFlex = PE2; // Flex sensor (Must be external interrupt enabled) pinTrigger = PE3; //The CAS pin pinTrigger2 = PE4; //The Cam Sensor pin #elif defined(CORE_STM32) //blue pill http://wiki.stm32duino.com/index.php?title=Blue_Pill //Maple mini http://wiki.stm32duino.com/index.php?title=Maple_Mini //pins PA12, PA11 are used for USB or CAN couldn't be used for GPIO pinInjector1 = PB7; //Output pin injector 1 is on pinInjector2 = PB6; //Output pin injector 2 is on pinInjector3 = PB5; //Output pin injector 3 is on pinInjector4 = PB4; //Output pin injector 4 is on pinCoil1 = PB3; //Pin for coil 1 pinCoil2 = PA15; //Pin for coil 2 pinCoil3 = PA14; //Pin for coil 3 pinCoil4 = PA9; //Pin for coil 4 pinCoil5 = PA8; //Pin for coil 5 pinTPS = A0; //TPS input pin pinMAP = A1; //MAP sensor pin pinIAT = A2; //IAT sensor pin pinCLT = A3; //CLS sensor pin pinO2 = A4; //O2 Sensor pin pinBat = A5; //Battery reference voltage pin pinBaro = pinMAP; pinIdle1 = PB2; //Single wire idle control pinIdle2 = PA2; //2 wire idle control pinBoost = PA1; //Boost control pinVVT_1 = PA0; //Default VVT output pinStepperDir = PC15; //Direction pin for DRV8825 driver pinStepperStep = PC14; //Step pin for DRV8825 driver pinStepperEnable = PC13; //Enable pin for DRV8825 pinDisplayReset = PB2; // OLED reset pin pinFan = PB1; //Pin for the fan output pinFuelPump = PB11; //Fuel pump output pinTachOut = PB10; //Tacho output pin //external interrupt enabled pins pinFlex = PB8; // Flex sensor (Must be external interrupt enabled) pinTrigger = PA10; //The CAS pin pinTrigger2 = PA13; //The Cam Sensor pin #endif break; case 9: //Pin mappings as per the MX5 PNP shield pinInjector1 = 11; //Output pin injector 1 is on pinInjector2 = 10; //Output pin injector 2 is on pinInjector3 = 9; //Output pin injector 3 is on pinInjector4 = 8; //Output pin injector 4 is on pinInjector5 = 14; //Output pin injector 5 is on pinCoil1 = 39; //Pin for coil 1 pinCoil2 = 41; //Pin for coil 2 pinCoil3 = 32; //Pin for coil 3 pinCoil4 = 33; //Pin for coil 4 pinCoil5 = 34; //Pin for coil 5 PLACEHOLDER value for now pinTrigger = 19; //The CAS pin pinTrigger2 = 18; //The Cam Sensor pin pinTPS = A2;//TPS input pin pinMAP = A5; //MAP sensor pin pinIAT = A0; //IAT sensor pin pinCLT = A1; //CLS sensor pin pinO2 = A3; //O2 Sensor pin pinBat = A4; //Battery reference voltage pin pinDisplayReset = 48; // OLED reset pin pinTachOut = 49; //Tacho output pin (Goes to ULN2803) pinIdle1 = 2; //Single wire idle control pinBoost = 4; pinIdle2 = 4; //2 wire idle control (Note this is shared with boost!!!) pinFuelPump = 37; //Fuel pump output pinStepperDir = 16; //Direction pin for DRV8825 driver pinStepperStep = 17; //Step pin for DRV8825 driver pinFan = 35; //Pin for the fan output pinLaunch = 12; //Can be overwritten below pinFlex = 3; // Flex sensor (Must be external interrupt enabled) pinResetControl = 44; //Reset control output #if defined(CORE_TEENSY) pinTrigger = 23; pinTrigger2 = 36; pinStepperDir = 34; pinStepperStep = 35; pinCoil1 = 33; //Done pinCoil2 = 24; //Done pinCoil3 = 51; //Won't work (No mapping for pin 32) pinCoil4 = 52; //Won't work (No mapping for pin 33) pinFuelPump = 26; //Requires PVT4 adapter or above pinFan = 50; //Won't work (No mapping for pin 35) pinTachOut = 28; //Done #endif break; case 10: #ifndef SMALL_FLASH_MODE //No support for bluepill here anyway //Pin mappings for user turtanas PCB pinInjector1 = 4; //Output pin injector 1 is on pinInjector2 = 5; //Output pin injector 2 is on pinInjector3 = 6; //Output pin injector 3 is on pinInjector4 = 7; //Output pin injector 4 is on pinInjector5 = 8; //Placeholder only - NOT USED pinInjector6 = 9; //Placeholder only - NOT USED pinInjector7 = 10; //Placeholder only - NOT USED pinInjector8 = 11; //Placeholder only - NOT USED pinCoil1 = 24; //Pin for coil 1 pinCoil2 = 28; //Pin for coil 2 pinCoil3 = 36; //Pin for coil 3 pinCoil4 = 40; //Pin for coil 4 pinCoil5 = 34; //Pin for coil 5 PLACEHOLDER value for now pinTrigger = 18; //The CAS pin pinTrigger2 = 19; //The Cam Sensor pin pinTPS = A2;//TPS input pin pinMAP = A3; //MAP sensor pin pinMAP2 = A8; //MAP2 sensor pin pinIAT = A0; //IAT sensor pin pinCLT = A1; //CLS sensor pin pinO2 = A4; //O2 Sensor pin pinBat = A7; //Battery reference voltage pin pinDisplayReset = 48; // OLED reset pin pinSpareTemp1 = A6; pinSpareTemp2 = A5; pinTachOut = 41; //Tacho output pin transistori puuttuu 2n2222 tähän ja 1k 12v pinFuelPump = 42; //Fuel pump output 2n2222 pinFan = 47; //Pin for the fan output pinTachOut = 49; //Tacho output pin pinFlex = 2; // Flex sensor (Must be external interrupt enabled) pinResetControl = 26; //Reset control output #endif break; case 20: #ifndef SMALL_FLASH_MODE //No support for bluepill here anyway //Pin mappings as per the Plazomat In/Out shields Rev 0.1 pinInjector1 = 8; //Output pin injector 1 is on pinInjector2 = 9; //Output pin injector 2 is on pinInjector3 = 10; //Output pin injector 3 is on pinInjector4 = 11; //Output pin injector 4 is on pinInjector5 = 12; //Output pin injector 5 is on pinCoil1 = 28; //Pin for coil 1 pinCoil2 = 24; //Pin for coil 2 pinCoil3 = 40; //Pin for coil 3 pinCoil4 = 36; //Pin for coil 4 pinCoil5 = 34; //Pin for coil 5 PLACEHOLDER value for now pinSpareOut1 = 4; //Spare LSD Output 1(PWM) pinSpareOut2 = 5; //Spare LSD Output 2(PWM) pinSpareOut3 = 6; //Spare LSD Output 3(PWM) pinSpareOut4 = 7; //Spare LSD Output 4(PWM) pinSpareOut5 = 50; //Spare LSD Output 5(digital) pinSpareOut6 = 52; //Spare LSD Output 6(digital) pinTrigger = 20; //The CAS pin pinTrigger2 = 21; //The Cam Sensor pin pinSpareTemp2 = A15; //spare Analog input 2 pinSpareTemp1 = A14; //spare Analog input 1 pinO2 = A8; //O2 Sensor pin pinBat = A4; //Battery reference voltage pin pinMAP = A3; //MAP sensor pin pinTPS = A2;//TPS input pin pinCLT = A1; //CLS sensor pin pinIAT = A0; //IAT sensor pin pinFan = 47; //Pin for the fan output pinFuelPump = 4; //Fuel pump output pinTachOut = 49; //Tacho output pin pinResetControl = 26; //Reset control output #endif break; case 30: #ifndef SMALL_FLASH_MODE //No support for bluepill here anyway //Pin mappings as per the dazv6 shield pinInjector1 = 8; //Output pin injector 1 is on pinInjector2 = 9; //Output pin injector 2 is on pinInjector3 = 10; //Output pin injector 3 is on pinInjector4 = 11; //Output pin injector 4 is on pinInjector5 = 12; //Output pin injector 5 is on pinCoil1 = 40; //Pin for coil 1 pinCoil2 = 38; //Pin for coil 2 pinCoil3 = 50; //Pin for coil 3 pinCoil4 = 52; //Pin for coil 4 pinCoil5 = 34; //Pin for coil 5 PLACEHOLDER value for now pinTrigger = 19; //The CAS pin pinTrigger2 = 18; //The Cam Sensor pin pinTrigger3 = 17; // cam sensor 2 pin pinTPS = A2;//TPS input pin pinMAP = A3; //MAP sensor pin pinIAT = A0; //IAT sensor pin pinCLT = A1; //CLS sensor pin pinO2 = A8; //O2 Sensor pin pinO2_2 = A9; //O2 sensor pin (second sensor) pinBat = A4; //Battery reference voltage pin pinDisplayReset = 48; // OLED reset pin pinTachOut = 49; //Tacho output pin pinIdle1 = 5; //Single wire idle control pinFuelPump = 45; //Fuel pump output pinStepperDir = 20; //Direction pin for DRV8825 driver pinStepperStep = 21; //Step pin for DRV8825 driver pinSpareHOut1 = 4; // high current output spare1 pinSpareHOut2 = 6; // high current output spare2 pinBoost = 7; pinSpareLOut1 = 43; //low current output spare1 pinSpareLOut2 = 47; pinSpareLOut3 = 49; pinSpareLOut4 = 51; pinSpareLOut5 = 53; pinFan = 47; //Pin for the fan output #endif break; case 40: //Pin mappings as per the NO2C shield pinInjector1 = 8; //Output pin injector 1 is on pinInjector2 = 9; //Output pin injector 2 is on pinInjector3 = 11; //Output pin injector 3 is on - NOT USED pinInjector4 = 12; //Output pin injector 4 is on - NOT USED pinInjector5 = 13; //Placeholder only - NOT USED pinCoil1 = 23; //Pin for coil 1 pinCoil2 = 22; //Pin for coil 2 pinCoil3 = 2; //Pin for coil 3 - ONLY WITH DB2 pinCoil4 = 3; //Pin for coil 4 - ONLY WITH DB2 pinCoil5 = 46; //Placeholder only - NOT USED pinTrigger = 19; //The CAS pin pinTrigger2 = 18; //The Cam Sensor pin pinTPS = A3; //TPS input pin pinMAP = A0; //MAP sensor pin pinIAT = A5; //IAT sensor pin pinCLT = A4; //CLT sensor pin pinO2 = A2; //O2 sensor pin pinBat = A1; //Battery reference voltage pin pinBaro = A6; //Baro sensor pin - ONLY WITH DB pinSpareTemp1 = A7; //spare Analog input 1 - ONLY WITH DB pinDisplayReset = 48; // OLED reset pin - NOT USED pinTachOut = 38; //Tacho output pin pinIdle1 = 5; //Single wire idle control pinIdle2 = 47; //2 wire idle control - NOT USED pinBoost = 7; //Boost control pinVVT_1 = 6; //Default VVT output pinFuelPump = 4; //Fuel pump output pinStepperDir = 25; //Direction pin for DRV8825 driver pinStepperStep = 24; //Step pin for DRV8825 driver pinStepperEnable = 27; //Enable pin for DRV8825 driver pinLaunch = 10; //Can be overwritten below pinFlex = 20; // Flex sensor (Must be external interrupt enabled) - ONLY WITH DB pinFan = 30; //Pin for the fan output - ONLY WITH DB pinSpareLOut1 = 32; //low current output spare1 - ONLY WITH DB pinSpareLOut2 = 34; //low current output spare2 - ONLY WITH DB pinSpareLOut3 = 36; //low current output spare3 - ONLY WITH DB pinResetControl = 26; //Reset control output break; case 41: #ifndef SMALL_FLASH_MODE //No support for bluepill here anyway //Pin mappings as per the UA4C shield pinInjector1 = 8; //Output pin injector 1 is on pinInjector2 = 7; //Output pin injector 2 is on pinInjector3 = 6; //Output pin injector 3 is on pinInjector4 = 5; //Output pin injector 4 is on pinInjector5 = 45; //Output pin injector 5 is on PLACEHOLDER value for now pinCoil1 = 35; //Pin for coil 1 pinCoil2 = 36; //Pin for coil 2 pinCoil3 = 33; //Pin for coil 3 pinCoil4 = 34; //Pin for coil 4 pinCoil5 = 44; //Pin for coil 5 PLACEHOLDER value for now pinTrigger = 19; //The CAS pin pinTrigger2 = 18; //The Cam Sensor pin pinFlex = 20; // Flex sensor pinTPS = A3; //TPS input pin pinMAP = A0; //MAP sensor pin pinBaro = A7; //Baro sensor pin pinIAT = A5; //IAT sensor pin pinCLT = A4; //CLS sensor pin pinO2 = A1; //O2 Sensor pin pinO2_2 = A9; //O2 sensor pin (second sensor) pinBat = A2; //Battery reference voltage pin pinSpareTemp1 = A8; //spare Analog input 1 pinLaunch = 37; //Can be overwritten below pinDisplayReset = 48; // OLED reset pin PLACEHOLDER value for now pinTachOut = 22; //Tacho output pin pinIdle1 = 9; //Single wire idle control pinIdle2 = 10; //2 wire idle control pinFuelPump = 23; //Fuel pump output pinVVT_1 = 11; //Default VVT output pinStepperDir = 32; //Direction pin for DRV8825 driver pinStepperStep = 31; //Step pin for DRV8825 driver pinStepperEnable = 30; //Enable pin for DRV8825 driver pinBoost = 12; //Boost control pinSpareLOut1 = 26; //low current output spare1 pinSpareLOut2 = 27; //low current output spare2 pinSpareLOut3 = 28; //low current output spare3 pinSpareLOut4 = 29; //low current output spare4 pinFan = 24; //Pin for the fan output //pinFan2 = 25; //Pin for the 2nd fan output pinResetControl = 46; //Reset control output PLACEHOLDER value for now #endif break; #if defined(CORE_TEENSY) case 50: //Pin mappings as per the teensy rev A shield pinInjector1 = 2; //Output pin injector 1 is on pinInjector2 = 10; //Output pin injector 2 is on pinInjector3 = 6; //Output pin injector 3 is on - NOT USED pinInjector4 = 9; //Output pin injector 4 is on - NOT USED //pinInjector5 = 13; //Placeholder only - NOT USED pinCoil1 = 29; //Pin for coil 1 pinCoil2 = 30; //Pin for coil 2 pinCoil3 = 31; //Pin for coil 3 - ONLY WITH DB2 pinCoil4 = 32; //Pin for coil 4 - ONLY WITH DB2 //pinCoil5 = 46; //Placeholder only - NOT USED pinTrigger = 23; //The CAS pin pinTrigger2 = 36; //The Cam Sensor pin pinTPS = 16; //TPS input pin pinMAP = 17; //MAP sensor pin pinIAT = 14; //IAT sensor pin pinCLT = 15; //CLT sensor pin pinO2 = A22; //O2 sensor pin pinO2_2 = A21; //O2 sensor pin (second sensor) pinBat = 18; //Battery reference voltage pin //pinBaro = A6; //Baro sensor pin - ONLY WITH DB //pinSpareTemp1 = A7; //spare Analog input 1 - ONLY WITH DB //pinDisplayReset = 48; // OLED reset pin - NOT USED pinTachOut = 20; //Tacho output pin pinIdle1 = 5; //Single wire idle control //pinIdle2 = 47; //2 wire idle control - NOT USED pinBoost = 11; //Boost control //pinVVT_1 = 6; //Default VVT output pinFuelPump = 38; //Fuel pump output pinStepperDir = 34; //Direction pin for DRV8825 driver pinStepperStep = 35; //Step pin for DRV8825 driver pinStepperEnable = 33; //Enable pin for DRV8825 driver pinLaunch = 26; //Can be overwritten below //pinFlex = 20; // Flex sensor (Must be external interrupt enabled) - ONLY WITH DB pinFan = 37; //Pin for the fan output - ONLY WITH DB //pinSpareLOut1 = 32; //low current output spare1 - ONLY WITH DB //pinSpareLOut2 = 34; //low current output spare2 - ONLY WITH DB //pinSpareLOut3 = 36; //low current output spare3 - ONLY WITH DB //pinResetControl = 26; //Reset control output pinSpareHOut1 = 8; // high current output spare1 pinSpareHOut2 = 7; // high current output spare2 pinSpareLOut1 = 21; //low current output spare1 break; case 51: //Pin mappings as per the teensy revB board shield pinInjector1 = 2; //Output pin injector 1 is on pinInjector2 = 10; //Output pin injector 2 is on pinInjector3 = 6; //Output pin injector 3 is on - NOT USED pinInjector4 = 9; //Output pin injector 4 is on - NOT USED //pinInjector5 = 13; //Placeholder only - NOT USED pinCoil1 = 29; //Pin for coil 1 pinCoil2 = 30; //Pin for coil 2 pinCoil3 = 31; //Pin for coil 3 - ONLY WITH DB2 pinCoil4 = 32; //Pin for coil 4 - ONLY WITH DB2 //pinCoil5 = 46; //Placeholder only - NOT USED pinTrigger = 23; //The CAS pin pinTrigger2 = 36; //The Cam Sensor pin pinTPS = 16; //TPS input pin pinMAP = 17; //MAP sensor pin pinIAT = 14; //IAT sensor pin pinCLT = 15; //CLT sensor pin pinO2 = A22; //O2 sensor pin pinO2_2 = A21; //O2 sensor pin (second sensor) pinBat = 18; //Battery reference voltage pin //pinBaro = A6; //Baro sensor pin - ONLY WITH DB //pinSpareTemp1 = A7; //spare Analog input 1 - ONLY WITH DB //pinDisplayReset = 48; // OLED reset pin - NOT USED pinTachOut = 20; //Tacho output pin pinIdle1 = 5; //Single wire idle control //pinIdle2 = 47; //2 wire idle control - NOT USED pinBoost = 11; //Boost control //pinVVT_1 = 6; //Default VVT output pinFuelPump = 38; //Fuel pump output pinStepperDir = 34; //Direction pin for DRV8825 driver pinStepperStep = 35; //Step pin for DRV8825 driver pinStepperEnable = 33; //Enable pin for DRV8825 driver pinLaunch = 26; //Can be overwritten below //pinFlex = 20; // Flex sensor (Must be external interrupt enabled) - ONLY WITH DB pinFan = 37; //Pin for the fan output - ONLY WITH DB //pinSpareLOut1 = 32; //low current output spare1 - ONLY WITH DB //pinSpareLOut2 = 34; //low current output spare2 - ONLY WITH DB //pinSpareLOut3 = 36; //low current output spare3 - ONLY WITH DB //pinResetControl = 26; //Reset control output pinSpareHOut1 = 8; // high current output spare1 pinSpareHOut2 = 7; // high current output spare2 pinSpareLOut1 = 21; //low current output spare1 break; #endif default: #ifndef SMALL_FLASH_MODE //No support for bluepill here anyway //Pin mappings as per the v0.2 shield pinInjector1 = 8; //Output pin injector 1 is on pinInjector2 = 9; //Output pin injector 2 is on pinInjector3 = 10; //Output pin injector 3 is on pinInjector4 = 11; //Output pin injector 4 is on pinInjector5 = 12; //Output pin injector 5 is on pinCoil1 = 28; //Pin for coil 1 pinCoil2 = 24; //Pin for coil 2 pinCoil3 = 40; //Pin for coil 3 pinCoil4 = 36; //Pin for coil 4 pinCoil5 = 34; //Pin for coil 5 PLACEHOLDER value for now pinTrigger = 20; //The CAS pin pinTrigger2 = 21; //The Cam Sensor pin pinTPS = A2; //TPS input pin pinMAP = A3; //MAP sensor pin pinIAT = A0; //IAT sensor pin pinCLT = A1; //CLS sensor pin pinO2 = A8; //O2 Sensor pin pinBat = A4; //Battery reference voltage pin pinStepperDir = 16; //Direction pin for DRV8825 driver pinStepperStep = 17; //Step pin for DRV8825 driver pinDisplayReset = 48; // OLED reset pin pinFan = 47; //Pin for the fan output pinFuelPump = 4; //Fuel pump output pinTachOut = 49; //Tacho output pin pinFlex = 3; // Flex sensor (Must be external interrupt enabled) pinBoost = 5; pinIdle1 = 6; pinResetControl = 43; //Reset control output #endif break; } //Setup any devices that are using selectable pins if ( (configPage6.launchPin != 0) && (configPage6.launchPin < BOARD_NR_GPIO_PINS) ) { pinLaunch = pinTranslate(configPage6.launchPin); } if ( (configPage4.ignBypassPin != 0) && (configPage4.ignBypassPin < BOARD_NR_GPIO_PINS) ) { pinIgnBypass = pinTranslate(configPage4.ignBypassPin); } if ( (configPage2.tachoPin != 0) && (configPage2.tachoPin < BOARD_NR_GPIO_PINS) ) { pinTachOut = pinTranslate(configPage2.tachoPin); } if ( (configPage4.fuelPumpPin != 0) && (configPage4.fuelPumpPin < BOARD_NR_GPIO_PINS) ) { pinFuelPump = pinTranslate(configPage4.fuelPumpPin); } if ( (configPage6.fanPin != 0) && (configPage6.fanPin < BOARD_NR_GPIO_PINS) ) { pinFan = pinTranslate(configPage6.fanPin); } if ( (configPage6.boostPin != 0) && (configPage6.boostPin < BOARD_NR_GPIO_PINS) ) { pinBoost = pinTranslate(configPage6.boostPin); } if ( (configPage6.vvtPin != 0) && (configPage6.vvtPin < BOARD_NR_GPIO_PINS) ) { pinVVT_1 = pinTranslate(configPage6.vvtPin); } if ( (configPage6.useExtBaro != 0) && (configPage6.baroPin < BOARD_NR_GPIO_PINS) ) { pinBaro = configPage6.baroPin + A0; } if ( (configPage6.useEMAP != 0) && (configPage10.EMAPPin < BOARD_NR_GPIO_PINS) ) { pinEMAP = configPage10.EMAPPin + A0; } //Currently there's no default pin for Idle Up pinIdleUp = pinTranslate(configPage2.idleUpPin); /* Reset control is a special case. If reset control is enabled, it needs its initial state set BEFORE its pinMode. If that doesn't happen and reset control is in "Serial Command" mode, the Arduino will end up in a reset loop because the control pin will go low as soon as the pinMode is set to OUTPUT. */ if ( (configPage4.resetControl != 0) && (configPage4.resetControlPin < BOARD_NR_GPIO_PINS) ) { resetControl = configPage4.resetControl; pinResetControl = pinTranslate(configPage4.resetControlPin); setResetControlPinState(); pinMode(pinResetControl, OUTPUT); } //Finally, set the relevant pin modes for outputs pinMode(pinCoil1, OUTPUT); pinMode(pinCoil2, OUTPUT); pinMode(pinCoil3, OUTPUT); pinMode(pinCoil4, OUTPUT); pinMode(pinCoil5, OUTPUT); pinMode(pinInjector1, OUTPUT); pinMode(pinInjector2, OUTPUT); pinMode(pinInjector3, OUTPUT); pinMode(pinInjector4, OUTPUT); pinMode(pinInjector5, OUTPUT); pinMode(pinTachOut, OUTPUT); pinMode(pinIdle1, OUTPUT); pinMode(pinIdle2, OUTPUT); pinMode(pinFuelPump, OUTPUT); pinMode(pinIgnBypass, OUTPUT); pinMode(pinFan, OUTPUT); pinMode(pinStepperDir, OUTPUT); pinMode(pinStepperStep, OUTPUT); pinMode(pinStepperEnable, OUTPUT); pinMode(pinBoost, OUTPUT); pinMode(pinVVT_1, OUTPUT); inj1_pin_port = portOutputRegister(digitalPinToPort(pinInjector1)); inj1_pin_mask = digitalPinToBitMask(pinInjector1); inj2_pin_port = portOutputRegister(digitalPinToPort(pinInjector2)); inj2_pin_mask = digitalPinToBitMask(pinInjector2); inj3_pin_port = portOutputRegister(digitalPinToPort(pinInjector3)); inj3_pin_mask = digitalPinToBitMask(pinInjector3); inj4_pin_port = portOutputRegister(digitalPinToPort(pinInjector4)); inj4_pin_mask = digitalPinToBitMask(pinInjector4); inj5_pin_port = portOutputRegister(digitalPinToPort(pinInjector5)); inj5_pin_mask = digitalPinToBitMask(pinInjector5); inj6_pin_port = portOutputRegister(digitalPinToPort(pinInjector6)); inj6_pin_mask = digitalPinToBitMask(pinInjector6); inj7_pin_port = portOutputRegister(digitalPinToPort(pinInjector7)); inj7_pin_mask = digitalPinToBitMask(pinInjector7); inj8_pin_port = portOutputRegister(digitalPinToPort(pinInjector8)); inj8_pin_mask = digitalPinToBitMask(pinInjector8); ign1_pin_port = portOutputRegister(digitalPinToPort(pinCoil1)); ign1_pin_mask = digitalPinToBitMask(pinCoil1); ign2_pin_port = portOutputRegister(digitalPinToPort(pinCoil2)); ign2_pin_mask = digitalPinToBitMask(pinCoil2); ign3_pin_port = portOutputRegister(digitalPinToPort(pinCoil3)); ign3_pin_mask = digitalPinToBitMask(pinCoil3); ign4_pin_port = portOutputRegister(digitalPinToPort(pinCoil4)); ign4_pin_mask = digitalPinToBitMask(pinCoil4); ign5_pin_port = portOutputRegister(digitalPinToPort(pinCoil5)); ign5_pin_mask = digitalPinToBitMask(pinCoil5); ign6_pin_port = portOutputRegister(digitalPinToPort(pinCoil6)); ign6_pin_mask = digitalPinToBitMask(pinCoil6); ign7_pin_port = portOutputRegister(digitalPinToPort(pinCoil7)); ign7_pin_mask = digitalPinToBitMask(pinCoil7); ign8_pin_port = portOutputRegister(digitalPinToPort(pinCoil8)); ign8_pin_mask = digitalPinToBitMask(pinCoil8); tach_pin_port = portOutputRegister(digitalPinToPort(pinTachOut)); tach_pin_mask = digitalPinToBitMask(pinTachOut); pump_pin_port = portOutputRegister(digitalPinToPort(pinFuelPump)); pump_pin_mask = digitalPinToBitMask(pinFuelPump); //And for inputs #if defined(CORE_STM32) #ifndef ARDUINO_ARCH_STM32 //libmaple core aka STM32DUINO pinMode(pinMAP, INPUT_ANALOG); pinMode(pinO2, INPUT_ANALOG); pinMode(pinO2_2, INPUT_ANALOG); pinMode(pinTPS, INPUT_ANALOG); pinMode(pinIAT, INPUT_ANALOG); pinMode(pinCLT, INPUT_ANALOG); pinMode(pinBat, INPUT_ANALOG); pinMode(pinBaro, INPUT_ANALOG); #else pinMode(pinMAP, INPUT); pinMode(pinO2, INPUT); pinMode(pinO2_2, INPUT); pinMode(pinTPS, INPUT); pinMode(pinIAT, INPUT); pinMode(pinCLT, INPUT); pinMode(pinBat, INPUT); pinMode(pinBaro, INPUT); #endif #endif pinMode(pinTrigger, INPUT); pinMode(pinTrigger2, INPUT); pinMode(pinTrigger3, INPUT); pinMode(pinFlex, INPUT_PULLUP); //Standard GM / Continental flex sensor requires pullup if (configPage6.lnchPullRes == true) { pinMode(pinLaunch, INPUT_PULLUP); } else { pinMode(pinLaunch, INPUT); } //If Launch Pull Resistor is not set make input float. if (configPage2.idleUpPolarity == 0) { pinMode(pinIdleUp, INPUT_PULLUP); } //Normal setting else { pinMode(pinIdleUp, INPUT); } //inverted setting //These must come after the above pinMode statements triggerPri_pin_port = portInputRegister(digitalPinToPort(pinTrigger)); triggerPri_pin_mask = digitalPinToBitMask(pinTrigger); triggerSec_pin_port = portInputRegister(digitalPinToPort(pinTrigger2)); triggerSec_pin_mask = digitalPinToBitMask(pinTrigger2); #if defined(CORE_STM32) #else //Set default values digitalWrite(pinMAP, HIGH); //digitalWrite(pinO2, LOW); digitalWrite(pinTPS, LOW); #endif } void initialiseTriggers() { byte triggerInterrupt = 0; // By default, use the first interrupt byte triggerInterrupt2 = 1; #if defined(CORE_AVR) switch (pinTrigger) { //Arduino Mega 2560 mapping case 2: triggerInterrupt = 0; break; case 3: triggerInterrupt = 1; break; case 18: triggerInterrupt = 5; break; case 19: triggerInterrupt = 4; break; case 20: triggerInterrupt = 3; break; case 21: triggerInterrupt = 2; break; default: triggerInterrupt = 0; break; //This should NEVER happen } #else triggerInterrupt = pinTrigger; #endif #if defined(CORE_AVR) switch (pinTrigger2) { //Arduino Mega 2560 mapping case 2: triggerInterrupt2 = 0; break; case 3: triggerInterrupt2 = 1; break; case 18: triggerInterrupt2 = 5; break; case 19: triggerInterrupt2 = 4; break; case 20: triggerInterrupt2 = 3; break; case 21: triggerInterrupt2 = 2; break; default: triggerInterrupt2 = 0; break; //This should NEVER happen } #else triggerInterrupt2 = pinTrigger2; #endif pinMode(pinTrigger, INPUT); pinMode(pinTrigger2, INPUT); pinMode(pinTrigger3, INPUT); //digitalWrite(pinTrigger, HIGH); detachInterrupt(triggerInterrupt); detachInterrupt(triggerInterrupt2); //Set the trigger function based on the decoder in the config switch (configPage4.TrigPattern) { case 0: //Missing tooth decoder triggerSetup_missingTooth(); trigger = triggerPri_missingTooth; triggerSecondary = triggerSec_missingTooth; getRPM = getRPM_missingTooth; getCrankAngle = getCrankAngle_missingTooth; triggerSetEndTeeth = triggerSetEndTeeth_missingTooth; if(configPage4.TrigEdge == 0) { attachInterrupt(triggerInterrupt, trigger, RISING); } // Attach the crank trigger wheel interrupt (Hall sensor drags to ground when triggering) else { attachInterrupt(triggerInterrupt, trigger, FALLING); } if(configPage4.TrigEdgeSec == 0) { attachInterrupt(triggerInterrupt2, triggerSec_missingTooth, RISING); } else { attachInterrupt(triggerInterrupt2, triggerSec_missingTooth, FALLING); } break; case 1: // Basic distributor triggerSetup_BasicDistributor(); trigger = triggerPri_BasicDistributor; getRPM = getRPM_BasicDistributor; getCrankAngle = getCrankAngle_BasicDistributor; triggerSetEndTeeth = triggerSetEndTeeth_BasicDistributor; if(configPage4.TrigEdge == 0) { attachInterrupt(triggerInterrupt, trigger, RISING); } // Attach the crank trigger wheel interrupt (Hall sensor drags to ground when triggering) else { attachInterrupt(triggerInterrupt, trigger, FALLING); } break; case 2: triggerSetup_DualWheel(); trigger = triggerPri_DualWheel; getRPM = getRPM_DualWheel; getCrankAngle = getCrankAngle_DualWheel; triggerSetEndTeeth = triggerSetEndTeeth_DualWheel; if(configPage4.TrigEdge == 0) { attachInterrupt(triggerInterrupt, trigger, RISING); } // Attach the crank trigger wheel interrupt (Hall sensor drags to ground when triggering) else { attachInterrupt(triggerInterrupt, trigger, FALLING); } if(configPage4.TrigEdgeSec == 0) { attachInterrupt(triggerInterrupt2, triggerSec_DualWheel, RISING); } else { attachInterrupt(triggerInterrupt2, triggerSec_DualWheel, FALLING); } break; case 3: triggerSetup_GM7X(); trigger = triggerPri_GM7X; getRPM = getRPM_GM7X; getCrankAngle = getCrankAngle_GM7X; triggerSetEndTeeth = triggerSetEndTeeth_GM7X; if(configPage4.TrigEdge == 0) { attachInterrupt(triggerInterrupt, trigger, RISING); } // Attach the crank trigger wheel interrupt (Hall sensor drags to ground when triggering) else { attachInterrupt(triggerInterrupt, trigger, FALLING); } break; case 4: triggerSetup_4G63(); trigger = triggerPri_4G63; getRPM = getRPM_4G63; getCrankAngle = getCrankAngle_4G63; triggerSetEndTeeth = triggerSetEndTeeth_4G63; attachInterrupt(triggerInterrupt, trigger, CHANGE); // Primary trigger connects to attachInterrupt(triggerInterrupt2, triggerSec_4G63, FALLING); break; case 5: triggerSetup_24X(); trigger = triggerPri_24X; getRPM = getRPM_24X; getCrankAngle = getCrankAngle_24X; triggerSetEndTeeth = triggerSetEndTeeth_24X; if(configPage4.TrigEdge == 0) { attachInterrupt(triggerInterrupt, trigger, RISING); } // Attach the crank trigger wheel interrupt (Hall sensor drags to ground when triggering) else { attachInterrupt(triggerInterrupt, trigger, FALLING); } // Primary trigger connects to attachInterrupt(triggerInterrupt2, triggerSec_24X, CHANGE); break; case 6: triggerSetup_Jeep2000(); trigger = triggerPri_Jeep2000; getRPM = getRPM_Jeep2000; getCrankAngle = getCrankAngle_Jeep2000; triggerSetEndTeeth = triggerSetEndTeeth_Jeep2000; if(configPage4.TrigEdge == 0) { attachInterrupt(triggerInterrupt, trigger, RISING); } // Attach the crank trigger wheel interrupt (Hall sensor drags to ground when triggering) else { attachInterrupt(triggerInterrupt, trigger, FALLING); } // Primary trigger connects to attachInterrupt(triggerInterrupt2, triggerSec_Jeep2000, CHANGE); break; case 7: triggerSetup_Audi135(); trigger = triggerPri_Audi135; getRPM = getRPM_Audi135; getCrankAngle = getCrankAngle_Audi135; triggerSetEndTeeth = triggerSetEndTeeth_Audi135; if(configPage4.TrigEdge == 0) { attachInterrupt(triggerInterrupt, trigger, RISING); } // Attach the crank trigger wheel interrupt (Hall sensor drags to ground when triggering) else { attachInterrupt(triggerInterrupt, trigger, FALLING); } attachInterrupt(triggerInterrupt2, triggerSec_Audi135, RISING); break; case 8: triggerSetup_HondaD17(); trigger = triggerPri_HondaD17; getRPM = getRPM_HondaD17; getCrankAngle = getCrankAngle_HondaD17; triggerSetEndTeeth = triggerSetEndTeeth_HondaD17; if(configPage4.TrigEdge == 0) { attachInterrupt(triggerInterrupt, trigger, RISING); } // Attach the crank trigger wheel interrupt (Hall sensor drags to ground when triggering) else { attachInterrupt(triggerInterrupt, trigger, FALLING); } // Primary trigger connects to attachInterrupt(triggerInterrupt2, triggerSec_HondaD17, CHANGE); break; case 9: triggerSetup_Miata9905(); trigger = triggerPri_Miata9905; getRPM = getRPM_Miata9905; getCrankAngle = getCrankAngle_Miata9905; triggerSetEndTeeth = triggerSetEndTeeth_Miata9905; //These may both need to change, not sure // Attach the crank trigger wheel interrupt (Hall sensor drags to ground when triggering) if(configPage4.TrigEdge == 0) { attachInterrupt(triggerInterrupt, trigger, RISING); } else { attachInterrupt(triggerInterrupt, trigger, FALLING); } if(configPage4.TrigEdgeSec == 0) { attachInterrupt(triggerInterrupt2, triggerSec_Miata9905, RISING); } else { attachInterrupt(triggerInterrupt2, triggerSec_Miata9905, FALLING); } break; case 10: triggerSetup_MazdaAU(); trigger = triggerPri_MazdaAU; getRPM = getRPM_MazdaAU; getCrankAngle = getCrankAngle_MazdaAU; triggerSetEndTeeth = triggerSetEndTeeth_MazdaAU; if(configPage4.TrigEdge == 0) { attachInterrupt(triggerInterrupt, trigger, RISING); } // Attach the crank trigger wheel interrupt (Hall sensor drags to ground when triggering) else { attachInterrupt(triggerInterrupt, trigger, FALLING); } // Primary trigger connects to attachInterrupt(triggerInterrupt2, triggerSec_MazdaAU, FALLING); break; case 11: triggerSetup_non360(); trigger = triggerPri_DualWheel; //Is identical to the dual wheel decoder, so that is used. Same goes for the secondary below getRPM = getRPM_non360; getCrankAngle = getCrankAngle_non360; triggerSetEndTeeth = triggerSetEndTeeth_Non360; if(configPage4.TrigEdge == 0) { attachInterrupt(triggerInterrupt, trigger, RISING); } // Attach the crank trigger wheel interrupt (Hall sensor drags to ground when triggering) else { attachInterrupt(triggerInterrupt, trigger, FALLING); } attachInterrupt(triggerInterrupt2, triggerSec_DualWheel, FALLING); //Note the use of the Dual Wheel trigger function here. No point in having the same code in twice. break; case 12: triggerSetup_Nissan360(); trigger = triggerPri_Nissan360; getRPM = getRPM_Nissan360; getCrankAngle = getCrankAngle_Nissan360; triggerSetEndTeeth = triggerSetEndTeeth_Nissan360; if(configPage4.TrigEdge == 0) { attachInterrupt(triggerInterrupt, trigger, RISING); } // Attach the crank trigger wheel interrupt (Hall sensor drags to ground when triggering) else { attachInterrupt(triggerInterrupt, trigger, FALLING); } attachInterrupt(triggerInterrupt2, triggerSec_Nissan360, CHANGE); break; case 13: triggerSetup_Subaru67(); trigger = triggerPri_Subaru67; getRPM = getRPM_Subaru67; getCrankAngle = getCrankAngle_Subaru67; triggerSetEndTeeth = triggerSetEndTeeth_Subaru67; if(configPage4.TrigEdge == 0) { attachInterrupt(triggerInterrupt, trigger, RISING); } // Attach the crank trigger wheel interrupt (Hall sensor drags to ground when triggering) else { attachInterrupt(triggerInterrupt, trigger, FALLING); } attachInterrupt(triggerInterrupt2, triggerSec_Subaru67, FALLING); break; case 14: triggerSetup_Daihatsu(); trigger = triggerPri_Daihatsu; getRPM = getRPM_Daihatsu; getCrankAngle = getCrankAngle_Daihatsu; triggerSetEndTeeth = triggerSetEndTeeth_Daihatsu; if(configPage4.TrigEdge == 0) { attachInterrupt(triggerInterrupt, trigger, RISING); } // Attach the crank trigger wheel interrupt (Hall sensor drags to ground when triggering) else { attachInterrupt(triggerInterrupt, trigger, FALLING); } //No secondary input required for this pattern break; case 15: triggerSetup_Harley(); trigger = triggerPri_Harley; //triggerSecondary = triggerSec_Harley; getRPM = getRPM_Harley; getCrankAngle = getCrankAngle_Harley; triggerSetEndTeeth = triggerSetEndTeeth_Harley; attachInterrupt(triggerInterrupt, trigger, RISING); // attachInterrupt(triggerInterrupt2, triggerSec_Harley, FALLING); break; case 16: //36-2-2-2 triggerSetup_ThirtySixMinus222(); trigger = triggerPri_ThirtySixMinus222; triggerSecondary = triggerSec_ThirtySixMinus222; getRPM = getRPM_missingTooth; //This uses the same function as the missing tooth decoder, so no need to duplicate code getCrankAngle = getCrankAngle_missingTooth; //This uses the same function as the missing tooth decoder, so no need to duplicate code triggerSetEndTeeth = triggerSetEndTeeth_ThirtySixMinus222; if(configPage4.TrigEdge == 0) { attachInterrupt(triggerInterrupt, trigger, RISING); } // Attach the crank trigger wheel interrupt (Hall sensor drags to ground when triggering) else { attachInterrupt(triggerInterrupt, trigger, FALLING); } if(configPage4.TrigEdgeSec == 0) { attachInterrupt(triggerInterrupt2, triggerSecondary, RISING); } else { attachInterrupt(triggerInterrupt2, triggerSecondary, FALLING); } break; default: trigger = triggerPri_missingTooth; getRPM = getRPM_missingTooth; getCrankAngle = getCrankAngle_missingTooth; if(configPage4.TrigEdge == 0) { attachInterrupt(triggerInterrupt, trigger, RISING); } // Attach the crank trigger wheel interrupt (Hall sensor drags to ground when triggering) else { attachInterrupt(triggerInterrupt, trigger, FALLING); } break; } }