90 lines
3.4 KiB
C++
90 lines
3.4 KiB
C++
/*
|
|
* This routine is used for doing any data conversions that are required during firmware changes
|
|
* This prevents users getting difference reports in TS when such a data change occurs.
|
|
* It also can be used for setting good values when there are viarables that move locations in the ini
|
|
* When a user skips multiple firmware versions at a time, this will roll through the updates 1 at a time
|
|
*/
|
|
|
|
|
|
void doUpdates()
|
|
{
|
|
#define CURRENT_DATA_VERSION 6
|
|
|
|
//May 2017 firmware introduced a -40 offset on the ignition table. Update that table to +40
|
|
if(EEPROM.read(EEPROM_DATA_VERSION) == 2)
|
|
{
|
|
for(int x=0; x<16; x++)
|
|
{
|
|
for(int y=0; y<16; y++)
|
|
{
|
|
ignitionTable.values[x][y] = ignitionTable.values[x][y] + 40;
|
|
}
|
|
}
|
|
writeAllConfig();
|
|
EEPROM.write(EEPROM_DATA_VERSION, 3);
|
|
}
|
|
//June 2017 required the forced addition of some CAN values to avoid weird errors
|
|
if(EEPROM.read(EEPROM_DATA_VERSION) == 3)
|
|
{
|
|
configPage10.speeduino_tsCanId = 0;
|
|
configPage10.true_address = 256;
|
|
configPage10.realtime_base_address = 336;
|
|
|
|
//There was a bad value in the May base tune for the spark duration setting, fix it here if it's a problem
|
|
if(configPage2.sparkDur == 255) { configPage2.sparkDur = 10; }
|
|
|
|
writeAllConfig();
|
|
EEPROM.write(EEPROM_DATA_VERSION, 4);
|
|
}
|
|
//July 2017 adds a cranking enrichment curve in place of the single value. This converts that single value to the curve
|
|
if(EEPROM.read(EEPROM_DATA_VERSION) == 4)
|
|
{
|
|
//Some default values for the bins (Doesn't matter too much here as the values against them will all be identical)
|
|
configPage11.crankingEnrichBins[0] = 0;
|
|
configPage11.crankingEnrichBins[1] = 40;
|
|
configPage11.crankingEnrichBins[2] = 70;
|
|
configPage11.crankingEnrichBins[3] = 100;
|
|
|
|
configPage11.crankingEnrichValues[0] = 100 + configPage1.crankingPct;
|
|
configPage11.crankingEnrichValues[1] = 100 + configPage1.crankingPct;
|
|
configPage11.crankingEnrichValues[2] = 100 + configPage1.crankingPct;
|
|
configPage11.crankingEnrichValues[3] = 100 + configPage1.crankingPct;
|
|
|
|
writeAllConfig();
|
|
EEPROM.write(EEPROM_DATA_VERSION, 5);
|
|
}
|
|
//September 2017 had a major change to increase the minimum table size to 128. This required multiple pieces of data being moved around
|
|
if(EEPROM.read(EEPROM_DATA_VERSION) == 5)
|
|
{
|
|
//Data after page 4 has to move back 128 bytes
|
|
for(int x=0; x < 1152; x++)
|
|
{
|
|
int endMem = EEPROM_CONFIG11_END - x;
|
|
int startMem = endMem - 128; //
|
|
byte currentVal = EEPROM.read(startMem);
|
|
EEPROM.update(endMem, currentVal);
|
|
}
|
|
//The remaining data only has to move back 64 bytes
|
|
for(int x=0; x < 352; x++)
|
|
{
|
|
int endMem = EEPROM_CONFIG11_END - 1152 - x;
|
|
int startMem = endMem - 64; //
|
|
byte currentVal = EEPROM.read(startMem);
|
|
EEPROM.update(endMem, currentVal);
|
|
}
|
|
|
|
EEPROM.write(EEPROM_DATA_VERSION, 6);
|
|
loadConfig(); //Reload the config after changing everything in EEPROM
|
|
}
|
|
|
|
//Final check is always for 255 and 0 (Brand new arduino)
|
|
if( (EEPROM.read(EEPROM_DATA_VERSION) == 0) || (EEPROM.read(EEPROM_DATA_VERSION) == 255) )
|
|
{
|
|
configPage10.true_address = 0x200;
|
|
EEPROM.write(EEPROM_DATA_VERSION, CURRENT_DATA_VERSION);
|
|
}
|
|
|
|
//Check to see if someone has downgraded versions:
|
|
if( EEPROM.read(EEPROM_DATA_VERSION) > CURRENT_DATA_VERSION ) { EEPROM.write(EEPROM_DATA_VERSION, CURRENT_DATA_VERSION); }
|
|
}
|