speeduino/globals.h

#include <Arduino.h>

const byte ms_version = 20;
const byte data_structure_version = 1; //This identifies the data structure when reading / writing. 
const byte page_size = 125;

//The status struct contains the current values for all 'live' variables
//In current version this is 64 bytes
struct statuses {
  volatile boolean hasSync;
  unsigned int RPM;
  byte MAP;
  byte TPS;
  byte VE;
  byte squirt;
  byte engine;
  unsigned long PW; //In uS
  
  //Helpful bitwise operations:
  //Useful reference: http://playground.arduino.cc/Code/BitMath
  // y = (x >> n) & 1;    // n=0..15.  stores nth bit of x in y.  y becomes 0 or 1.
  // x &= ~(1 << n);      // forces nth bit of x to be 0.  all other bits left alone.
  // x |= (1 << n);       // forces nth bit of x to be 1.  all other bits left alone.
  
};


//Page 1 of the config - See the ini file for further reference
//This mostly covers off variables that are required for fuel
struct config1 {
  /*
  byte engineCylinders; 1 // May support more than 1 cyl later. Always will assume 1 injector per cylinder. 
  byte engineInjectorSize; 80 // In cc/min
  byte engineStoich; 14.7 // Stoichiometric ratio of fuel used
  byte engineStrokes; 4 //Can be 2 stroke or 4 stroke, any other value will cause problems
  byte engineDwell; 3000 //The spark dwell time in uS
  */
  
  byte crankCold; //Cold cranking pulsewidth modifier. This is added to the fuel pulsewidth when cranking under a certain temp threshold (ms)
  byte crankHot; //Warm cranking pulsewidth modifier. This is added to the fuel pulsewidth when cranking (ms)
  byte asePct; //Afterstart enrichment (%)
  byte aseCount; //Afterstart enrichment cycles. This is the number of ignition cycles that the afterstart enrichment % lasts for
  byte wueBins[10]; //Warm up enrichment array (10 bytes)
  byte taeBins1; //TPS based acceleration enrichment bin 1 of 4 (ms)
  byte taeBins2; //TPS based acceleration enrichment bin 2 of 4 (ms)
  byte taeBins3; //TPS based acceleration enrichment bin 3 of 4 (ms)
  byte taeBins4; //TPS based acceleration enrichment bin 4 of 4 (ms)
  byte taeColdA;
  byte tpsThresh;
  byte taeTime;
  byte tdePct;
  byte egoTemp; //The temperature at which the EGO / O2 sensor values start being used (Degrees)
  byte egoCount;
  byte egoDelta;
  byte egoLimit;
  byte reqFuel;
  byte divider;
  byte alternate;
  byte injOpen;
  byte injOCfuel;
  byte injPwmP;
  byte injPwmT;
  byte battFac; //Whether to compensate pulsewidth for battery voltage (ms/v)
  int rpmk;

  byte mapType;
  byte strokes;
  byte injType;
  byte nCylinders; //Number of cylinders
  byte cltType;
  byte matType;
  byte nInjectors; //Number of injectors
  byte engineType;
  byte egoType;
  byte algorithm; //"Speed Density", "Alpha-N"
  byte baroCorr;
  byte primePulse;
  byte egoRPM;
  byte fastIdleT; //Fast idle temperature
  byte egoSwitch;
  byte taeColdM;
  byte unused1;
  byte unused2;
  byte unused3;
  byte unused4;
  byte unused5;
  byte unused6;
  
};

//Page 2 of the config - See the ini file for further reference
//This mostly covers off variables that are required for ignition
struct config2 {
  
  byte triggerAngle;
  byte FixAng;
  byte Trim;
  byte CrankAng;
  byte IgHold;
  byte Trig_plus;
  byte TrigCrank;
  byte IgInv;
  byte oddfire;
  byte IdleAdv;
  byte IdleAdvTPS;
  byte IdleAdvRPM;
  byte IdleAdvCLT;
  byte IdleDelayTime;
  byte StgCycles;
  byte dwellCont; //Fixed duty dwell control
  byte dwellCrank;
  byte dwellRun;
  byte triggerTeeth; //The full count of teeth on the trigger wheel if there were no gaps
  byte triggerMissingTeeth; //The size of the tooth gap (ie number of missing teeth)
  byte unused1; //100
  byte unused2;
  byte unused3;
  byte unused4;
  byte unused5;
  byte unused6;
  byte unused7;
  byte unused8;
  byte unused9;
  byte unused10;
  byte unused11;
  byte unused12;
  byte unused13;
  byte unused14;
  byte unused15;
  byte unused16;
  byte unused17;
  byte unused18;
  byte unused19;
  byte unused20;
  byte unused21;
  byte unused22;
  byte unused23;
  byte unused24;
  byte unused25;
  byte unused26;
  byte unused27;
  byte unused28;
  byte unused29; //128
  
};