Fix boost and vvt eeprom offsets

reference/speeduino.ini

@@ -65,7 +65,7 @@
    pageSize            = 288,   64,     288,    64,     288,    64,     64,    160
    pageActivationDelay = 10
 ;  pageActivate        = ""
-   pageActivate        = "P\001",   "P\002", "P\003", "P\004", "P\005", "P\006", "P\007"
+   pageActivate        = "P\001",   "P\002", "P\003", "P\004", "P\005", "P\006", "P\007", "P\010"
    pageReadCommand     = "V",       "V",     "V",     "V",     "V",     "V",     "V",     "V"
    pageValueWrite      = "W%2o%v",   "W%o%v", "W%2o%v", "W%o%v", "W%2o%v", "W%o%v", "W%o%v", "W%o%v"
    ;\x00%2

speeduino.ino

@@ -114,13 +114,11 @@ void setup()
   table3D_setSize(&fuelTable, 16);
   table3D_setSize(&ignitionTable, 16);
   table3D_setSize(&afrTable, 16);
+  table3D_setSize(&boostTable, 8);
+  table3D_setSize(&vvtTable, 8);
   
   loadConfig();
   
-  //Boost and vvt tables are only created if they are turned on
-  if(configPage3.boostEnabled) { table3D_setSize(&boostTable, 8); }
-  if(configPage3.vvtEnabled) { table3D_setSize(&vvtTable, 8); }
-  
   //Repoint the 2D table structs to the config pages that were just loaded
   taeTable.valueSize = SIZE_BYTE; //Set this table to use byte values
   taeTable.xSize = 4;
@@ -507,8 +505,6 @@ void loop()
       currentStatus.tpsADC = fastMap1023toX(analogRead(pinTPS), 0, 1023, 0, 255); //Get the current raw TPS ADC value and map it into a byte
       currentStatus.TPS = map(currentStatus.tpsADC, configPage1.tpsMin, configPage1.tpsMax, 0, 100); //Take the raw TPS ADC value and convert it into a TPS% based on the calibrated values
       currentStatus.TPS_time = currentLoopTime;   
-      
-      boostControl(); //Most boost tends to run at about 30Hz, so placing it here ensures a new target time is fetched at least that frequently
     }
     
     //The IAT and CLT readings can be done less frequently. This still runs about 4 times per second
@@ -526,6 +522,9 @@ void loop()
        currentStatus.IAT = iatCalibrationTable[currentStatus.iatADC] - CALIBRATION_TEMPERATURE_OFFSET;
        currentStatus.O2 = o2CalibrationTable[currentStatus.O2ADC];
        currentStatus.O2_2 = o2CalibrationTable[currentStatus.O2_2ADC];
+       
+      vvtControl();
+      boostControl(); //Most boost tends to run at about 30Hz, so placing it here ensures a new target time is fetched frequently enough
     }
 
     //Always check for sync
@@ -549,7 +548,6 @@ void loop()
         } 
       
       idleControl(); //Perform any idle realted actions
-      vvtControl();
       //END SETTING STATUSES
       //-----------------------------------------------------------------------------------------------------
       

storage.ino

@@ -188,13 +188,13 @@ void writeConfig()
   }
   //TPS/MAP bins
   y=EEPROM_CONFIG8_YBINS2;
-  for(int x=EEPROM_CONFIG8_YBINS1; x<EEPROM_CONFIG8_END; x++) 
+  for(int x=EEPROM_CONFIG8_YBINS1; x<EEPROM_CONFIG8_XSIZE2; x++) 
   {
     offset = x - EEPROM_CONFIG8_YBINS1;
     if(EEPROM.read(x) != boostTable.axisY[offset]) { EEPROM.write(x, boostTable.axisY[offset]); }
-    offset = x - EEPROM_CONFIG8_YBINS1;
+    offset = y - EEPROM_CONFIG8_YBINS2;
     if(EEPROM.read(y) != vvtTable.axisY[offset]) { EEPROM.write(y, vvtTable.axisY[offset]); }
-    x++;
+    y++;
   }
 }
 
@@ -311,7 +311,6 @@ void loadConfig()
   
   //*********************************************************************************************************************************************************************************
   // Boost and vvt tables load
-  
   int y = EEPROM_CONFIG8_MAP2;
   for(int x=EEPROM_CONFIG8_MAP1; x<EEPROM_CONFIG8_XBINS1; x++) 
   { 
@@ -321,6 +320,7 @@ void loadConfig()
     vvtTable.values[7-offset/8][offset%8] = EEPROM.read(y); //Read the 8x8 map
     y++;
   }
+
   //RPM bins
   y = EEPROM_CONFIG8_XBINS2;
   for(int x=EEPROM_CONFIG8_XBINS1; x<EEPROM_CONFIG8_YBINS1; x++) 
@@ -331,9 +331,10 @@ void loadConfig()
     vvtTable.axisX[offset] = (EEPROM.read(y) * 100); //RPM bins are divided by 100 when stored. Multiply them back now
     y++;
   }
+    
   //TPS/MAP bins
   y = EEPROM_CONFIG8_YBINS2;
-  for(int x=EEPROM_CONFIG8_YBINS1; x<EEPROM_CONFIG8_END; x++) 
+  for(int x=EEPROM_CONFIG8_YBINS1; x<EEPROM_CONFIG8_XSIZE2; x++) 
   {
     offset = x - EEPROM_CONFIG8_YBINS1;
     boostTable.axisY[offset] = EEPROM.read(x);