INI file fixes (#615)
* Add missing commas * Missing closing brace * Missing & Was using bitwise comparison (&): looks like it should be boolean (&&) * Remove extra closing brace "}" Co-authored-by: Josh Stewart <josh@noisymime.org>
This commit is contained in:
tx_haggis
GitHub
parent
118e3d40a5
commit
ef03225c32
|
|
@ -338,7 +338,7 @@ page = 1
|
|||
idleUpPin = bits, U08, 57, [0:5], "Board Default", "INVALID", "INVALID", "3", "4", "5", "6", "7", "8", "9", "10", "11", "12", "13", "14", "15", "16", "17", "18", "19", "20", "21", "22", "23", "24", "25", "26", "27", "28", "29", "30", "31", "32", "33", "34", "35", "36", "37", "38", "39", "40", "41", "42", "43", "44", "45", "46", "47", "48", "49", "50", "51", "52", "53", "INVALID", "A8", "A9", "A10", "A11", "A12", "A13", "A14", "A15", "INVALID"
|
||||
idleUpPolarity= bits, U08, 57, [6:6], "Normal", "Inverted"
|
||||
idleUpEnabled = bits, U08, 57, [7:7], "Off", "On"
|
||||
idleUpAdder = scalar, U08, 58, "% / Steps" 1.0, 0.0, 0.0, 250.0, 0
|
||||
idleUpAdder = scalar, U08, 58, "% / Steps", 1.0, 0.0, 0.0, 250.0, 0
|
||||
aeTaperMin = scalar, U08, 59, "RPM", 100, 0.0, 1000, 10000, 0
|
||||
aeTaperMax = scalar, U08, 60, "RPM", 100, 0.0, 2000, 10000, 0
|
||||
|
||||
|
|
@ -380,7 +380,7 @@ page = 1
|
|||
idleAdvRPM = scalar, U08, 93, "rpm", 100, 0.0, 100, 25500, 0
|
||||
idleAdvTPS = scalar, U08, 94, "%", 1, 0, 0, 120, 0
|
||||
|
||||
injAngRPM = array, U08, 95, [4], "RPM" 100, 0.0, 100, 10000, 0
|
||||
injAngRPM = array, U08, 95, [4], "RPM", 100, 0.0, 100, 10000, 0
|
||||
idleTaperTime = scalar, U08, 99, "S", 0.1, 0.0, 0.0, 25.5, 1
|
||||
dfcoDelay = scalar, U08, 100, "S", 0.1, 0.0, 0.0, 25.5, 1 ;Remainder of DFCO settings are in page 4
|
||||
#if CELSIUS
|
||||
|
|
@ -393,7 +393,7 @@ page = 1
|
|||
vssMode = bits, U08, 102, [0:1], "Off", "INVALID", "Pulses per KM", "Pulses per mile" ;INVALID value will be CAN
|
||||
;vssPullup = bits, U08, 102, [1:1], "Off", "On"
|
||||
vssPin = bits, U08, 102, [2:7], "Board Default", "INVALID", "INVALID", "3", "4", "5", "6", "7", "8", "9", "10", "11", "12", "13", "14", "15", "16", "17", "18", "19", "20", "21", "22", "23", "24", "25", "26", "27", "28", "29", "30", "31", "32", "33", "34", "35", "36", "37", "38", "39", "40", "41", "42", "43", "44", "45", "46", "47", "48", "49", "50", "51", "52", "53", "INVALID", "A8", "A9", "A10", "A11", "A12", "A13", "A14", "A15", "INVALID"
|
||||
vssPulsesPerKm= scalar, U16, 103, "pulses" 1.0, 0.0, 0.0, 25500, 0
|
||||
vssPulsesPerKm= scalar, U16, 103, "pulses", 1.0, 0.0, 0.0, 25500, 0
|
||||
vssSmoothing = scalar, U08, 105, "%", 1.0, 0, 0, 255, 0
|
||||
vssRatio1 = scalar, U16, 106, "km/h per 1000rpm", 0.1, 0, 0, 99.9, 1
|
||||
vssRatio2 = scalar, U16, 108, "km/h per 1000rpm", 0.1, 0, 0, 99.9, 1
|
||||
|
|
@ -411,10 +411,10 @@ page = 1
|
|||
primingDelay = scalar, U08, 120, "S", 0.1, 0.0, 0.0, 25.5, 1
|
||||
|
||||
iacTPSlimit = scalar, U08, 121, "%", 1, 0, 0, 100, 0
|
||||
iacRPMlimitHysteresis = scalar, U08, 122, "RPM" 10, 0 10 2500, 0
|
||||
iacRPMlimitHysteresis = scalar, U08, 122, "RPM", 10, 0, 10, 2500, 0
|
||||
|
||||
rtc_trim = scalar, S08, 123, "ppm", 1, 0, -127, +127, 0
|
||||
idleAdvVss = scalar, U08, 124, "km/h", 1 0.0, 0.0, 255, 0
|
||||
idleAdvVss = scalar, U08, 124, "km/h", 1, 0.0, 0.0, 255, 0
|
||||
mapSwitchPoint = scalar, U08, 125, "RPM", 100, 0.0, 0.0, 16320, 0
|
||||
unused2-95 = array, U08, 126, [2], "%", 1.0, 0.0, 0.0, 255, 0
|
||||
|
||||
|
|
@ -454,7 +454,7 @@ page = 4
|
|||
useResync = bits, U08, 6,[7:7], "No", "Yes"
|
||||
sparkDur = scalar, U08, 7, "ms", 0.1, 0, 0, 25.5, 1 ; Spark duration
|
||||
trigPatternSec = bits,U08, 8,[0:6], "Single tooth cam", "4-1 cam", "Poll level", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID"
|
||||
PollLevelPol = bits, U08, 8,[7:7], "Low", "High",
|
||||
PollLevelPol = bits, U08, 8,[7:7], "Low", "High"
|
||||
|
||||
;Reset Control
|
||||
bootloaderCaps = scalar, U08, 9, "level", 1, 0, 0, 255, 0
|
||||
|
|
@ -552,7 +552,7 @@ page = 4
|
|||
|
||||
vvt2CL0DutyAng = scalar, S16, 121, "deg", 1.0, 0.0, -360.0, 360.0, 0 ; * ( 2 bytes)
|
||||
vvt2PWMdir = bits, U08, 123, [0:0], "Advance", "Retard"
|
||||
unusedBits4-123 = bits, U08, 123, [1:7],
|
||||
unusedBits4-123 = bits, U08, 123, [1:7]
|
||||
ANGLEFILTER_VVT = scalar, U08, 124, "%", 1.0, 0.0, 0, 100, 0
|
||||
FILTER_FLEX = scalar, U08, 125, "%", 1.0, 0.0, 0, 240, 0
|
||||
|
||||
|
|
@ -2444,7 +2444,7 @@ menuDialog = main
|
|||
|
||||
dialog = idleUpOutputSettingsPanel, "Idle Up Output Settings", yAxis
|
||||
field = "Idle Up Output Enabled", idleUpOutputEnabled, { idleUpEnabled }
|
||||
field = "Idle Up Output Inverted", idleUpOutputInv, { idleUpEnabled && idleUpOutputEnabled
|
||||
field = "Idle Up Output Inverted", idleUpOutputInv, { idleUpEnabled && idleUpOutputEnabled }
|
||||
field = "Idle Up Output Pin", idleUpOutputPin, { idleUpEnabled && idleUpOutputEnabled }
|
||||
|
||||
dialog = idleUpSettings, "Idle Up Settings"
|
||||
|
|
@ -2515,8 +2515,8 @@ menuDialog = main
|
|||
field = "cranking before the injectors and coils are fired"
|
||||
field = "Trigger edge", TrigEdge { TrigPattern != 4 } ;4G63 uses both edges
|
||||
field = "Secondary trigger edge", TrigEdgeSec, { (TrigPattern == 0 && TrigSpeed == 0 && trigPatternSec != 2) || TrigPattern == 2 || TrigPattern == 9 || TrigPattern == 12 || TrigPattern == 18 || TrigPattern == 19 || TrigPattern == 20 } ;Missing tooth, dual wheel and Miata 9905, weber-marelli, ST170
|
||||
field = "Missing Tooth Secondary type" trigPatternSec, { (TrigPattern == 0&& TrigSpeed == 0) }
|
||||
field = "Level for 1st phase" PollLevelPol, { (TrigPattern == 0 && TrigSpeed == 0 && trigPatternSec == 2) }
|
||||
field = "Missing Tooth Secondary type", trigPatternSec, { (TrigPattern == 0&& TrigSpeed == 0) }
|
||||
field = "Level for 1st phase", PollLevelPol, { (TrigPattern == 0 && TrigSpeed == 0 && trigPatternSec == 2) }
|
||||
field = "Trigger Filter", TrigFilter, { TrigPattern != 13 }
|
||||
field = "Re-sync every cycle", useResync, { TrigPattern == 2 || TrigPattern == 4 || TrigPattern == 7 || TrigPattern == 12 || TrigPattern == 9 || TrigPattern == 13 || TrigPattern == 18 || TrigPattern == 19 } ;Dual wheel, 4G63, Audi 135, Nissan 360, Miata 99-05, weber-marelli
|
||||
|
||||
|
|
@ -2973,7 +2973,7 @@ menuDialog = main
|
|||
dialog = outputtestinj1, "Injector CH1", yAxis
|
||||
commandButton = "Off", cmdtestinj1off,{testactive}
|
||||
commandButton = "50% DC", cmdtestinj150dc,{!testenabled && testactive}
|
||||
commandButton = "On", cmdtestinj1on,{!testenabled & testactive}
|
||||
commandButton = "On", cmdtestinj1on,{!testenabled && testactive}
|
||||
dialog = outputtestinj2, "Injector CH2", yAxis
|
||||
commandButton = "Off", cmdtestinj2off,{testactive && nFuelChannels >= 2 }
|
||||
commandButton = "50% DC", cmdtestinj250dc,{!testenabled && testactive && nFuelChannels >= 2 }
|
||||
|
|
@ -2993,7 +2993,7 @@ menuDialog = main
|
|||
dialog = outputtestinj6, "Injector CH6", yAxis
|
||||
commandButton = "Off", cmdtestinj6off,{ testactive && nFuelChannels >= 6 }
|
||||
commandButton = "50% DC", cmdtestinj650dc,{!testenabled && testactive && nFuelChannels >= 6 }
|
||||
commandButton = "On", cmdtestinj6on ,{ !testenabled & testactive && nFuelChannels >= 6 }
|
||||
commandButton = "On", cmdtestinj6on ,{ !testenabled && testactive && nFuelChannels >= 6 }
|
||||
dialog = outputtestinj7, "Injector CH7", yAxis
|
||||
commandButton = "Off", cmdtestinj7off,{ testactive && nFuelChannels >= 7 }
|
||||
commandButton = "50% DC", cmdtestinj750dc,{!testenabled && testactive && nFuelChannels >= 7 }
|
||||
|
|
@ -3001,7 +3001,7 @@ menuDialog = main
|
|||
dialog = outputtestinj8, "Injector CH8", yAxis
|
||||
commandButton = "Off", cmdtestinj8off,{ testactive && nFuelChannels >= 8 }
|
||||
commandButton = "50% DC", cmdtestinj850dc,{!testenabled && testactive && nFuelChannels >= 8 }
|
||||
commandButton = "On", cmdtestinj8on ,{ !testenabled & testactive && nFuelChannels >= 8 }
|
||||
commandButton = "On", cmdtestinj8on ,{ !testenabled && testactive && nFuelChannels >= 8 }
|
||||
|
||||
dialog = outputtest_injectors, "Injector Driver Output Test", xAxis
|
||||
panel = outputtestinj1
|
||||
|
|
@ -3227,16 +3227,16 @@ menuDialog = main
|
|||
field = "", caninput_sel11extsourcea, {(caninput_sel11a == 1 || caninput_sel11b == 1) }, {enable_secondarySerial && (!enable_intcan || (enable_intcan && !intcan_available))}
|
||||
field = "", caninput_sel11extsourceb, {(caninput_sel11a == 1 || caninput_sel11b == 1) }, {enable_secondarySerial && (enable_intcan && intcan_available)}
|
||||
field = "", caninput_sel11extsourcec, {(caninput_sel11a == 1 || caninput_sel11b == 1) }, {!enable_secondarySerial && (enable_intcan && intcan_available)}
|
||||
field = "", caninput_sel12extsourcea, {(caninput_sel12a == 1 || caninput_sel12b == 1) }, {enable_secondarySerial && (!enable_intcan || (enable_intcan && !intcan_available))}}
|
||||
field = "", caninput_sel12extsourcea, {(caninput_sel12a == 1 || caninput_sel12b == 1) }, {enable_secondarySerial && (!enable_intcan || (enable_intcan && !intcan_available))}
|
||||
field = "", caninput_sel12extsourceb, {(caninput_sel12a == 1 || caninput_sel12b == 1) }, {enable_secondarySerial && (enable_intcan && intcan_available)}
|
||||
field = "", caninput_sel12extsourcec, {(caninput_sel12a == 1 || caninput_sel12b == 1) }, {!enable_secondarySerial && (enable_intcan && intcan_available)}
|
||||
field = "", caninput_sel13extsourcea, {(caninput_sel13a == 1 || caninput_sel13b == 1) }, {enable_secondarySerial && (!enable_intcan || (enable_intcan && !intcan_available))}}
|
||||
field = "", caninput_sel13extsourcea, {(caninput_sel13a == 1 || caninput_sel13b == 1) }, {enable_secondarySerial && (!enable_intcan || (enable_intcan && !intcan_available))}
|
||||
field = "", caninput_sel13extsourceb, {(caninput_sel13a == 1 || caninput_sel13b == 1) }, {enable_secondarySerial && (enable_intcan && intcan_available)}
|
||||
field = "", caninput_sel13extsourcec, {(caninput_sel13a == 1 || caninput_sel13b == 1) }, {!enable_secondarySerial && (enable_intcan && intcan_available)}
|
||||
field = "", caninput_sel14extsourcea, {(caninput_sel14a == 1 || caninput_sel14b == 1) }, {enable_secondarySerial && (!enable_intcan || (enable_intcan && !intcan_available))}}
|
||||
field = "", caninput_sel14extsourcea, {(caninput_sel14a == 1 || caninput_sel14b == 1) }, {enable_secondarySerial && (!enable_intcan || (enable_intcan && !intcan_available))}
|
||||
field = "", caninput_sel14extsourceb, {(caninput_sel14a == 1 || caninput_sel14b == 1) }, {enable_secondarySerial && (enable_intcan && intcan_available)}
|
||||
field = "", caninput_sel14extsourcec, {(caninput_sel14a == 1 || caninput_sel14b == 1) }, {!enable_secondarySerial && (enable_intcan && intcan_available)}
|
||||
field = "", caninput_sel15extsourcea, {(caninput_sel15a == 1 || caninput_sel15b == 1) }, {enable_secondarySerial && (!enable_intcan || (enable_intcan && !intcan_available))}}
|
||||
field = "", caninput_sel15extsourcea, {(caninput_sel15a == 1 || caninput_sel15b == 1) }, {enable_secondarySerial && (!enable_intcan || (enable_intcan && !intcan_available))}
|
||||
field = "", caninput_sel15extsourceb, {(caninput_sel15a == 1 || caninput_sel15b == 1) }, {enable_secondarySerial && (enable_intcan && intcan_available)}
|
||||
field = "", caninput_sel15extsourcec, {(caninput_sel15a == 1 || caninput_sel15b == 1) }, {!enable_secondarySerial && (enable_intcan && intcan_available)}
|
||||
|
||||
|
|
@ -4520,7 +4520,7 @@ cmdVSSratio6 = "E\x99\x06"
|
|||
reqFuelGauge = req_fuel, "Req. Fuel", "ms", 0, 35.0, 1.0, 1.2, 20, 25, 2, 2
|
||||
mapMultiplyGauge = map_multiply_amt, "MAP Multiply", "%", 0, 200, 130, 140, 140, 150, 0, 0
|
||||
nSquirtsGauge = nSquirts, "# Squirts", "", 0, 10, 130, 140, 140, 150, 0, 0
|
||||
syncLossGauge = syncLossCounter, "# Sync Losses" "", 0, 255, -1, -1, 10, 50, 0, 0
|
||||
syncLossGauge = syncLossCounter, "# Sync Losses", "", 0, 255, -1, -1, 10, 50, 0, 0
|
||||
;-------------------------------------------------------------------------------
|
||||
|
||||
[FrontPage]
|
||||
|
|
@ -4543,7 +4543,7 @@ cmdVSSratio6 = "E\x99\x06"
|
|||
;----------------------------------------------------------------------------
|
||||
; Indicators
|
||||
; expr off-label on-label, off-bg, off-fg, on-bg, on-fg
|
||||
indicator = { running }, "Not Running", "Running" white, black, green, black
|
||||
indicator = { running }, "Not Running", "Running", white, black, green, black
|
||||
indicator = { crank }, "Not Cranking", "Cranking", white, black, green, black
|
||||
indicator = { ase }, "ASE OFF", "ASE ON", white, black, green, black
|
||||
indicator = { warmup }, "WUE OFF", "WUE ON", white, black, green, black
|
||||
|
|
|
|||
Loading…
Reference in New Issue