Flex pin is still not user selectable in TS, but maybe added at some point. This also allows use of this on board configs.
Also switch to using div100 in the fuel temp code.
* adding VVT logging and trigger edge editing
fix missing define (temp fix?)
Revert "fix missing define (temp fix?)"
This reverts commit c6280f38ff69cc41278148a79c888736a71754b1.
fixes
* Create an additional logger screen in tunerstudio
Changes to create a third high speed logger window in tuner studio.
* Change variable name
Discord discussion requested compositeLogEnabled didn't do a test for false as the type is now a byte. Variable renamed to be compositeTriggerUsed and false replaced with 0. Variable name and values used should now make more logical sense.
* added more logging
Log the primary, secondary and third inputs as well as engine cycle on all composite logs. Still have 3 different logs to allow you to visualise which is the best way to present the information.
* Remove serialCRC - only used within parseSerial()
Also hoist the CRC read into a function.
* Minimize global variable visibility
* Encapsulate write of multi-byte primitives
* Factor out sendBufferAndCrc()
* Push safety test into TS_CommandButtonsHandler()
* Extract writePage()
* Simpler parsing
* Remove some functions from public interface
* Store constant arrays in progmem
* Centralize high speed logger start/stop code
* Factor out loadO2Calibration()
* Factor out temperature calibration table update functions
* Remove dead code
* Fix sendToothLog()
* Fix sendCompositeLog()
* Replace tooth log send booleans with an enum
Saves a byte
* Remove sendBufferAndCrcProgMem()
Use serialPayload to send
* Whitespace clean up
* Optimize comms.cpp for size
* Replace global unsigned long with bool
Saves 2 bytes
* Replace 2 global bools with an enum
Saves a byte, reads better.
* Remove global FastCRC instance
* Make sendSerialReturnCode blocking.
It was using non-blocking functions but was never
re-entered.
Rename to make blocking & non-blocking calls
more obvious.
* Use one uint16_t to track RX/TX byte count
* Simplify new comms log tx API
* Extract loadPageToBuffer function
* All endianess changes use the same code
* Doxygen comments and code organization
* Remove serialWriteUpdateCrc() & updateTmpCalibration()
* Combine SerialStatus & logSendStatus enums.
Makes sense since we can only be doing one thing at a time.
* Remove global inProgressCompositeTime
Only used when sending composite log
* Replace 3 global bools with expanded SerialStatus enum
* Remove unused global tsCanId
* Limit scope of some comms globals.
* Remove isMap global - replace witth function
* Reduce the serial API to only 2 calls
transmit & receive
* Tidy up #define visibility
* Fix Black* build errors
* Workaround Teensy code race condition
availableForWrite() is not reliable.
* Prevent race condition
Was pematurely setting the serialStatusFlag to
SERIAL_INACTIVE before final CRC ws read from
serial.
* Use post write buffer availability checks
Remove buffer size check prior to writing.
* Write multi-byte values as single bytes.
(attempt to fix Teensy 3.5 issue)
* Only use Serial.available() as a boolean test
(Teensy fix)
* writeNonBlocking checks Serial.write() return value
* Non-blocking CRC write
In sendBufferAndCrcNonBlocking().
* Fix compile warning
* Set serial status flag prior to transmitting!
* Reliable blocking byte writes.
* Fix timeout code: not firing under some conditions
* MISRA fixes
* Add decel enleanment feature
* Fix tps and map DOT scaling in TS.
* updates.ino
* Small bug fix.
* One more small bug fix.
* Update cancomms.ino
Cast tps/mapDOT as uint8 to cancomms to retain backwards compatibility
* Fix programmable outputs list.
* Fix programmable outputs in updates.ino
* Add abs around currentStatus.mapDOT
* 19.09.2021
* Final testing of AC Control, some idle features fixed
AC control feature added, better than the existing idle-up feature (which can still be used for other things, e.g. electrical load detection). Air conditioning is locked out with coolant temp, RPM high/low, and high TPS. So the A/C automatically cuts out when driving hard.
Idle step now works correctly with closed loop PWM, open loop PWM, and closed+open loop PWM. Untested with stepper motor, but no reason it shouldn't work.
* Fixed mistakenly incremented page sizes
* Initial changes as per HWright9
-Renamed engineRunSeconds to acAfterEngineStartDelay
-Formatted large if statements better
-Fixed acStartDelay overflow bug
-Improved readability of logic
* Final fixes as per HWright9's feedback
-Add high/low RPM lockout delay, similar to the high TPM lockout delay
-General tidy-up
* Added stand-alone fan, moved config data in EEPROM
-Added additional configurable stand-alone A/C fan output, for when there is dedicated cooling fan for the A/C compressor. This is independent of the engine cooling fan logic.
-Moved config storage in EEPROM to configPage9, as noisymime's SD card logging has used the (previously unused) bytes I had used in configPage13.
-Minor bug fix - rename Aux in 1-16 to Aux in 0-15
* Revert to current master branch - as of master commit 97f8ef795a
* A/C Control Re-Integrated from AC-Control-Clean-3 (@Corey-Harding). Tested & ready to merge.
Additionally, added @HazuTo25's lines into the update() routine to configure default A/C settings.
* Changed updates.ino to just set A/C to disabled
* Fix change reverted by mistake - master merge commit 73badbce8c
* Fix remaining mistakes from previous master merge
* Remove test statements left in by mistake
* define unusedBits
* Remove test statements left in by mistake
* Increase timing granularity to 0.1s
* idleUpRPMAdder
* Remove another line put in by mistake by auto merge
* idleUpRPMFixes
* Update speeduino.ino
* Tweak A/C idle up descriptions
* Tweak A/C TS descriptors again
* Fixed alignment bug that turned page 15 config values into gobbledegook.
This had the symptom of the A/C request never triggering, because when a pin was assigned in TS (e.g. I did 27), a completely different pin would be read from config15 (in my case 22 - connecting the button to pin 22 would work in this case, even though TS was set to 27).
* Fix bit count - should be 6 to match ini file
* Increase minimum RPM lockout granularity
* Change granularity of A/C minimum RPM lockout to 10 RPM; Inline some functions for readability
* Add static inline function prototypes to auxiliaries.h as per the style guide.
* Fixed page 15 merge errors
* Style changes to suit new pinIsUsed() checks in setPinMappings()
* Add PWM Fan Control Minimum Clamp Value when A/C Compressor Engaged
* Fix comment
* Fix bug with stand-alone fan initialisation
Pin was unable to be used in prog. I/O even if fan was disabled, because it was always initialised as an output even if it was disabled. Fixed in this commit.
* Correction to Fahrenheit temperature scaling
* Move A/C updates to correct next release
Co-authored-by: shiznit304 <62686180+shiznit304@users.noreply.github.com>
Co-authored-by: Josh Stewart <josh@noisymime.org>
* Added PWM Fan functionality
PWM Fan output for Teensy and STM32
* Teensy3.5 timer fix for PWM Fan.
* Fix the conflicts with incorporate AFR
* Possibility to use PWM fan on mega too
Not tested at this stage!! Do not merge yet.
* Fix log entry size
* Remove duplicate stuff and use same way off toggling fan
* Fix typo errors
* Move fan pin definitions to globals.h
* Fix problems related to PWM fan.
* Revert previous change.
* Fix problems with idle things
* fix idle duty getting stuck at 100%
* Revert "fix idle duty getting stuck at 100%"
This reverts commit 7e9779483b.
* Revert "Fix problems with idle things"
This reverts commit 8bccb56d9a.
* Revert "Revert previous change."
This reverts commit fcb962864a.
* Remove mega support
* fixes
* more fixes
* moar fixes
* Should be working now
* Update speeduino.ini
* Lots of tweaking
* Update to work better with current FW
* Fix compiler warnings and include update things.
* Minor fixes
* Update logger.ino
* Fan duty working on mega too and fan output will be on/off
Co-authored-by: Pasi Kemppainen <pazi88@users.noreply.github.com>
* doxygen warning fixes
* run doxygen -u, add speeduino logo to src tree for doxygen
* increase DOT_GRAPH_MAX_NODES
so we generate the complete call graph for loop() and setup()
* [VVT] PID work
Tested on a half moon CAM pattern as working, it should work on others too.
Added option to reverse the PWM output
Co-Authored-By: pazi88 <48950874+pazi88@users.noreply.github.com>
* Fix typo
Co-Authored-By: diy-efi <diy-efi@users.noreply.github.com>
* Add second VVT pwm on same timer
All precious VVT variables was renamed to VVT1 and added VVT2 stuff.
Tested with logic analyzer.
* Define VVT2 for other boards
Added vvt2Pin
* Just update on first tooth
Co-authored-by: pazi88 <48950874+pazi88@users.noreply.github.com>
Co-authored-by: diy-efi <diy-efi@users.noreply.github.com>
Josh Stewart
mike501
tx_haggis
Pasi Kemppainen
Afroboltski
Daniel Tobias
Vitor Moreno B. Sales