Go to file
Josh Stewart 109f64f342 Memory allocation and TS interface for flat shift 2017-01-17 13:33:41 +11:00
reference Memory allocation and TS interface for flat shift 2017-01-17 13:33:41 +11:00
src Add digitalWriteFast to src directory (It's effectively a lib) 2016-10-26 10:38:39 +11:00
.gitignore Further work on v0.4 board 2015-06-28 22:50:20 +10:00
LICENSE Add explicit license information 2015-05-29 09:49:44 +10:00
README.md Update README.md 2016-02-25 13:21:32 +11:00
auxiliaries.h Number of scope check fixes 2016-10-26 01:04:37 +11:00
auxiliaries.ino Improved fan on/off logic 2016-10-27 08:49:27 +11:00
cancomms.h Bring formatting in line with standards 2016-10-01 01:57:57 +10:00
cancomms.ino Cleanup some compile warnings 2017-01-11 18:30:46 +11:00
comms.h Correct packetSize of comms 2016-12-27 17:03:27 +11:00
comms.ino Add more pressure gauge options (PSI, inhg) 2017-01-16 14:41:40 +11:00
contributing.md Create contributing.md 2016-10-26 16:54:06 +11:00
corrections.h Cleanup some compile warnings 2017-01-11 18:30:46 +11:00
corrections.ino Cleanup some compile warnings 2017-01-11 18:30:46 +11:00
decoders.h Better filter options for 4g63 2017-01-01 19:56:04 +11:00
decoders.ino Better filter options for 4g63 2017-01-01 19:56:04 +11:00
display.h Initial I2C OLED display work. Functioning. 2015-03-01 08:27:16 +11:00
display.ino Complete (untested) sequential fuel trim 2016-10-27 17:27:08 +11:00
errors.h Default error values 2016-08-03 12:11:47 +10:00
errors.ino Cleanup of a few compiler warnings 2016-10-11 22:17:15 +11:00
globals.h Memory allocation and TS interface for flat shift 2017-01-17 13:33:41 +11:00
idle.h Add check to prevent potential crash when switching IAC methods (Teensy) 2017-01-12 22:33:26 +11:00
idle.ino Add check to prevent potential crash when switching IAC methods (Teensy) 2017-01-12 22:33:26 +11:00
math.h Setup math.h properly 2016-10-26 10:41:23 +11:00
math.ino Setup math.h properly 2016-10-26 10:41:23 +11:00
scheduler.h Enable ignition channel 5 on Teensy (Prevent compile error) 2017-01-11 17:38:59 +11:00
scheduler.ino Enable ignition channel 5 on Teensy (Prevent compile error) 2017-01-11 17:38:59 +11:00
sensors.h Platform check on ADC interrupt. Fixes #59 2016-11-21 16:45:21 +11:00
sensors.ino Final tidy up of ADC interrupt before merge 2016-11-18 13:42:51 +11:00
speeduino.ino Remove old tach code 2017-01-12 21:57:04 +11:00
storage.h Fixes for trim table comms misalignment 2016-11-01 12:37:00 +11:00
storage.ino Storage changes to allow for MAP value up to 511 kpa 2017-01-16 22:14:07 +11:00
table.h Enable MAP load values up to 511 2017-01-17 10:51:53 +11:00
table.ino Merge branch 'master' into ADC-interrupt 2016-11-10 07:48:47 +11:00
timers.h Move overdwell calc out of the 1ms timer 2016-11-21 16:46:13 +11:00
timers.ino Remove old tach code 2017-01-12 21:57:04 +11:00
utils.h Fix average cycle MAP reading when engine is off (Also begins move of sensor readings to own file) 2016-03-09 16:40:11 +11:00
utils.ino Experimental new tacho output method 2017-01-06 17:30:22 +11:00

README.md

Speeduino

FAQ:

Q: Speeduino, didn't you used to be called something else?

A: Initial aim was for a simple DIY ECU for go-karts and the original project title was kartduino. As it became apparent that we wanted to extend support to larger vehicles, the name became a bit misleading. The important ideas though remain the same and the priority is still SIMPLICITY! The code is written with simplicity above all else in mind and all areas are well commented. The project can be loaded directly into the Arduino IDE and compiled with only a single additional library needing to be added. Where code is complex or low level, a high level pseudo code example is given to explain what is being performed.

========================================================================

Q: Arduino ECU,pffft, heard THAT before. Does this one actually work?

A: Yep! 1, 2, 4, 6 and 8 cylinder engines have all run, fuel and ignition, off Speeduino.

========================================================================

Q: So what can it do?

A: Take a look at this page for details: http://speeduino.com/wiki/index.php/Overview

========================================================================

Q: Target platform?

A: Arduino Mega (Or other ATmega1280 / ATmega2560 powered SKU) will be required. Standard arduino models are not suitable for multi-cylinder engines due to their lack of 16-bit timers. The shield board has been designed around the Mega and it is not expected that there will be a non-Mega variant.

========================================================================

Q: I'm trying to get started or need some general help. What should I do?

A: Support is all through the forum at: http://speeduino.com/forum

========================================================================

Q: I must know more! How can I contact you?

A: Come and visit the forum : http://speeduino.com/forum

If you still need some more info, feel free to drop me a line: noisymime (AT) gmail (dot) com