2006-07-28 07:45:44 -07:00
<ecus >
<ecu_tools >
<convert_factor type= "afr" name= "Convert Lambda to AFR" metric= "AFR" expr= "[value]*14.7" />
<convert_factor type= "temp" name= "Convert Celsius to Fahrenheit" metric= "F" expr= "([value]*9/5)+32" />
<convert_factor type= "press" name= "Convert PSI to Bar" metric= "Bar" expr= "[value]*0.06894757" />
<convert_factor type= "speed" name= "Convert km/h to mph" metric= "mph" expr= "[value]*0.6213712" />
<convert_factor type= "inj" name= "Convert Injector Milliseconds to Duty %" metric= "%"
expr="GetLogParam(" Engine Speed" )*([value]/1200)"/>
</ecu_tools>
<logprotocols >
2006-07-29 04:35:13 -07:00
<logprotocol type= "SSM" default= "ssmbase" >
2006-07-28 07:45:44 -07:00
<ecu id= "base" name= "SSM base" type= "ssmbase" >
<parameter id= "Engine Speed" offset= "#000E" storagetype= "uint16" decimals= "0" bit= "1" byte= "1" expr= "[value]/4" metric= "RPM"
desc="Engine speed in Revolutions Per Minute. More accurate than your|tachometer, which will normally indicate higher."/>
<parameter id= "Manifold Absolute Pressure" offset= "#000D" storagetype= "uint8" decimals= "3" type= "press" bit= "2" byte= "1"
expr="[value]*37/255" metric="PSI"
desc="Absolute pressure read by the MAP sensor typically located just after|the throttle body. Absolute pressure means air pressure including|amtospheric, therefore the values normall seen here are Atmospheric|Pressure plus any boost pressure."/>
<parameter id= "Air/Fuel Learning #2" offset= "#000C" storagetype= "uint8" decimals= "2" bit= "3" byte= "1" expr= "([value]-128)*100/128"
metric="%"
desc="Fuel trim corrections made by the ECU while in closed loop. This value|is based on trends seen in the Air/Fuel Trim Immediate field.|Adjustments are made slower. The combined value of this field and the|Air/Fuel Trim Immediate field equal your total fuel trim. This|correction is not directly active when in open loop."/>
<parameter id= "Air/Fuel Correction #2" offset= "#000B" storagetype= "uint8" decimals= "2" bit= "4" byte= "1" expr= "([value]-128)*100/128"
metric="%"
desc="Fuel trim corrections made by the ECU while in closed loop. This|value is updated most frequently. Adjustments are made based on the|values provided by the Front O2 Sensor. This correction is not active|when in open loop."/>
<parameter id= "Air/Fuel Learning #1" offset= "#000A" storagetype= "uint8" decimals= "2" bit= "5" byte= "1" expr= "([value]-128)*100/128"
metric="%"
desc="Fuel trim corrections made by the ECU while in closed loop. This value|is based on trends seen in the Air/Fuel Trim Immediate field.|Adjustments are made slower. The combined value of this field and the|Air/Fuel Trim Immediate field equal your total fuel trim. This|correction is not directly active when in open loop."/>
<parameter id= "Air/Fuel Correction #1" offset= "#0009" storagetype= "uint8" decimals= "2" bit= "6" byte= "1" expr= "([value]-128)*100/128"
metric="%"
desc="Fuel trim corrections made by the ECU while in closed loop. This|value is updated most frequently. Adjustments are made based on the|values provided by the Front O2 Sensor. This correction is not active|when in open loop."/>
<parameter id= "Coolant Temperature" offset= "#0008" storagetype= "uint8" decimals= "2" type= "temp" bit= "7" byte= "1" expr= "([value]-40)"
metric="B C"
desc="Engine coolant temperature reading. Do not base your decision on|engine operating temperature on this value. The engine oil will take|slightly longer to heat up than the coolant."/>
<parameter id= "Engine Load" offset= "#0007" storagetype= "uint8" decimals= "2" bit= "8" byte= "1" expr= "[value]*100/255" metric= "g/s"
desc="Calculated engine load based on a number of conditions such as MAF|sensor reading, engine coolant temp, etc. This represents how hard|the engine is being asked to work. Load does not simply mean boost.|This value is used as an axis reference point on many of the ECU maps."/>
<parameter id= "Front O2 Sensor #2" offset= "#001A" storagetype= "uint16" decimals= "3" bit= "1" byte= "2" expr= "[value]*5/1000" metric= "V"
desc="Voltage of the O2 sensor. These sensors do not report an accurate|Air/Fuel ratio but instead provide a rich/lean signal to the ECU.|Their output voltages switches sharply as the AFR crosses the|stoichiometric ratio. Values of ~0 to ~0.9 are normal. 0 being lean|and 0.9 being very rich."/>
<parameter id= "Rear O2 Sensor" offset= "#0018" storagetype= "uint16" decimals= "3" bit= "2" byte= "2" expr= "[value]*5/1000" metric= "V"
desc="Voltage of the O2 sensor. These sensors do not report an accurate|Air/Fuel ratio but instead provide a rich/lean signal to the ECU.|Their output voltages switches sharply as the AFR crosses the|stoichiometric ratio. Values of ~0 to ~0.9 are normal. 0 being lean|and 0.9 being very rich."/>
<parameter id= "Front O2 Sensor #1" offset= "#0016" storagetype= "uint16" decimals= "3" bit= "3" byte= "2" expr= "[value]*5/1000" metric= "V"
desc="Voltage of the O2 sensor. These sensors do not report an accurate|Air/Fuel ratio but instead provide a rich/lean signal to the ECU.|Their output voltages switches sharply as the AFR crosses the|stoichiometric ratio. Values of ~0 to ~0.9 are normal. 0 being lean|and 0.9 being very rich."/>
<parameter id= "Throttle Opening Angle" offset= "#0015" storagetype= "uint8" decimals= "2" bit= "4" byte= "2" expr= "[value]*100/255"
metric="%" desc="Percentage displaying how much the throttle blade has opened. 100% =|wide open throttle."/>
<parameter id= "Mass Air Flow" offset= "#0013" storagetype= "uint16" decimals= "2" bit= "5" byte= "2" expr= "[value]/100" metric= "g/s"
desc="Mass air flow sensor value in gram of air per second. Measured by the|MAF sensor located just after your intake air box."/>
<parameter id= "Intake Air Temperature" offset= "#0012" storagetype= "uint8" decimals= "2" type= "temp" bit= "6" byte= "2"
expr="([value]-40)" metric="B C"
desc="Temperature of the air drawn into the engine for combustion.|Generally measured as the point of entry to the air box. This does|NOT give an indication of actual charge air temperature. This value|is useful to the ECU for determination of the wastegate duty cycle|required to produce a given boost pressure. Higher boost pressures|may be achieved with lower wastegate duty cycles when the IAT is low."/>
<parameter id= "Ignition Timing" offset= "#0011" storagetype= "uint8" decimals= "0" bit= "7" byte= "2" expr= "([value]-128)/2"
metric="B BTDC"
desc="Actual spark advance Before Top Dead Center after all corrections have|been made. This is the actual timing value the engine is experiencing|after all the knock correction and environment corrections have been|made."/>
<parameter id= "Vehicle Speed" offset= "#0010" storagetype= "uint8" decimals= "0" type= "speed" bit= "8" byte= "2" expr= "[value]"
metric="KPH"
desc="Actual vehicle speed. This value is updated slower but may beore|accurate than what your speedometer. This value may not be accurate|if the car wheels or tyres have been changed from standard, since this|changes the rolling circumference."/>
<parameter id= "Atmospheric Pressure" offset= "#0023" storagetype= "uint8" decimals= "3" type= "press" bit= "1" byte= "3"
expr="[value]*37/255" metric="PSI"
desc="Measured atmospheric pressure. At sea-level this should be around|1bar or 14.5PSI. On some vehicles this value is not updated|continuously since a single pressure sensor is shared for reading both|manifold and atmospheric pressure."/>
<parameter id= "Knock Correction" offset= "#0022" storagetype= "uint8" decimals= "0" bit= "2" byte= "3" expr= "([value]-128)/2"
metric="B BTDC"
desc="This value represents how much additional ignition timing is being|added/removed to/from the primary ignition table. + values are|ignition advance and indicate the absence of knock. -ve values are|ignition retard and may indicate that the engine knock sensor is|detecting some knock. This value is generated by the Ignition Advance|Multiplier and the Knock Correction map."/>
<parameter id= "Fuel Injector #2 Pulse Width" offset= "#0021" storagetype= "uint8" decimals= "2" type= "inj" bit= "3" byte= "3"
expr="[value]*256/1000" metric="ms"
desc="Represents how long the injector has been sent a signal to open. This|includes both the injector latency time as well as the time the|injector actually flowed fuel. If you are regularly seeing over 90%|duty, you may need bigger injectors."/>
<parameter id= "Fuel Injector #1 Pulse Width" offset= "#0020" storagetype= "uint8" decimals= "2" type= "inj" bit= "4" byte= "3"
expr="[value]*256/1000" metric="ms"
desc="Represents how long the injector has been sent a signal to open. This|includes both the injector latency time as well as the time the|injector actually flowed fuel. If you are regularly seeing over 90%|duty, you may need bigger injectors."/>
<parameter id= "Differential Pressure Sensor Voltage" offset= "#001F" storagetype= "uint8" decimals= "3" bit= "5" byte= "3"
expr="[value]*2/100" metric="V" desc=""/>
<parameter id= "Throttle Sensor Voltage" offset= "#001E" storagetype= "uint8" decimals= "3" bit= "6" byte= "3" expr= "[value]*2/100"
metric="V" desc="Voltage generated by the throttle sensor. As throttle blade angle|increases, voltage increases."/>
<parameter id= "Air Flow Sensor Voltage" offset= "#001D" storagetype= "uint8" decimals= "3" bit= "7" byte= "3" expr= "[value]*2/100"
metric="V" desc="Voltage generated by the MAF sensor. As air flow increases, voltage|increases."/>
<parameter id= "Battery Voltage" offset= "#001C" storagetype= "uint8" decimals= "3" bit= "8" byte= "3" expr= "[value]*8/100" metric= "V"
desc="Voltage measured at the ECU. May be as low as 10 volts when the|ignition is off, should rise to ~14 volts when the engine is running."/>
<parameter id= "Front O2 Heater #1" offset= "#002B" storagetype= "uint8" decimals= "3" bit= "1" byte= "4" expr= "[value]*1004/25600"
metric="Amps" desc=""/>
<parameter id= "Fuel Temperature" offset= "#002A" storagetype= "uint8" decimals= "2" type= "temp" bit= "2" byte= "4" expr= "([value]-40)"
metric="B C" desc=""/>
<parameter id= "Accelerator Opening Angle" offset= "#0029" storagetype= "uint8" decimals= "2" bit= "3" byte= "4" expr= "[value]*100/256"
metric="%" desc=""/>
<parameter id= "Learned Ignition Timing" offset= "#0028" storagetype= "uint8" decimals= "0" bit= "4" byte= "4" expr= "([value]-128)/2"
metric="B BTDC" desc=""/>
<parameter id= "CO Adjustment" offset= "#0027" storagetype= "uint8" decimals= "3" bit= "5" byte= "4" expr= "[value]*2/100" metric= "V"
desc=""/>
<parameter id= "Fuel Tank Pressure" offset= "#0026" storagetype= "uint8" decimals= "3" type= "press" bit= "6" byte= "4"
expr="([value]-128)*35/10000" metric="PSI" desc=""/>
<parameter id= "Pressure Differential Sensor" offset= "#0025" storagetype= "uint8" decimals= "3" bit= "7" byte= "4"
expr="([value]-128)*37/255" metric="PSI" desc=""/>
<parameter id= "Manifold Relative Pressure" offset= "#0024" storagetype= "uint8" decimals= "3" type= "press" bit= "8" byte= "4"
expr="([value]-128)*37/255" metric="PSI"
desc="Calculated by the ECU from subtracting the Air Pressure sensor value|against the Manifold Absolute Pressure sensor. The result is relative|or " boost" pressure, which is what is shown by a boost gauge."/>
<parameter id= "Tumble Valve Position Sensor Right" offset= "#0033" storagetype= "uint8" decimals= "3" bit= "1" byte= "5"
expr="[value]*2/100" metric="V" desc="Voltage generated by the tumble value position sensor."/>
<parameter id= "CPC Valve Duty Ratio" offset= "#0032" storagetype= "uint8" decimals= "2" bit= "2" byte= "5" expr= "[value]*100/255"
metric="%" desc="Charge Purge Cannister"/>
<parameter id= "Secondary Wastegate Duty Cycle" offset= "#0031" storagetype= "uint8" decimals= "2" bit= "3" byte= "5" expr= "[value]*100/255"
metric="%"
desc="Duty cycle used to drive the boost control solenoid. This is the|final value used after corrections. Very helpful in tuning the boost|control system. The higher the duty cycles the more exhaust gas is|being used to drive the turbocharger. As the wastegate is opened more|exhaust gases are by-passed to reduce the boost pressure generated by|the turbo."/>
<parameter id= "Primary Wastegate Duty Cycle" offset= "#0030" storagetype= "uint8" decimals= "2" bit= "4" byte= "5" expr= "[value]*100/255"
metric="%"
desc="Duty cycle used to drive the boost control solenoid. This is the|final value used after corrections. Very helpful in tuning the boost|control system. The higher the duty cycles the more exhaust gas is|being used to drive the turbocharger. As the wastegate is opened more|exhaust gases are by-passed to reduce the boost pressure generated by|the turbo."/>
<parameter id= "Fuel Level Voltage" offset= "#002E" storagetype= "uint8" decimals= "3" bit= "6" byte= "5" expr= "[value]*2/100" metric= "V"
desc="Voltage generated by the fuel level sensor inside the fuel tank."/>
<parameter id= "Front O2 Heater #2" offset= "#002D" storagetype= "uint8" decimals= "3" bit= "7" byte= "5" expr= "[value]*1004/25600"
metric="Amps" desc=""/>
<parameter id= "Rear O2 Heater Current" offset= "#002C" storagetype= "uint8" decimals= "3" bit= "8" byte= "5" expr= "[value]*1004/25600"
metric="Amps" desc=""/>
<parameter id= "Fuel Pump Duty" offset= "#003B" storagetype= "uint8" decimals= "2" bit= "1" byte= "6" expr= "[value]*100/255" metric= "%"
desc="Duty cycle used to drive the fuel pump. At idle and very low load|conditions, the duty cycle is reduced to extend the pump's life time|and importantly reduces fuel temperature at idle and this reduces fuel|system related emissions."/>
<parameter id= "Alternator Duty" offset= "#003A" storagetype= "uint8" decimals= "2" bit= "2" byte= "6" expr= "[value]" metric= "%"
desc="On some cars the alternator duty can be controlled by the ECU. This|allows the load on the engine from the alternator to be controlled.|The ECU may reduce the alternator load at high engine loads to reduce|the power drawn from the engine."/>
<parameter id= "Number Of Ex. Gas Recirc Steps" offset= "#0039" storagetype= "uint8" decimals= "2" bit= "3" byte= "6" expr= "[value]"
metric="steps" desc=""/>
<parameter id= "Idle Speed Control Valve Step" offset= "#0038" storagetype= "uint8" decimals= "2" bit= "4" byte= "6" expr= "[value]"
metric="steps" desc=""/>
<parameter id= "Air/Fuel Heater Duty" offset= "#0037" storagetype= "uint8" decimals= "2" bit= "5" byte= "6" expr= "[value]*100/255"
metric="%" desc=""/>
<parameter id= "Air/Fuel Lean Correction" offset= "#0036" storagetype= "uint8" decimals= "2" bit= "6" byte= "6" expr= "[value]*100/255"
metric="%" desc=""/>
<parameter id= "Idle Speed Control Valve Duty Ratio" offset= "#0035" storagetype= "uint8" decimals= "2" bit= "7" byte= "6" expr= "[value]/2"
metric="%"
desc="Duty cycle used to maintain idle speed. Controls the amount of air|let into the manifold when the engine is idling. It is normal to see|this value fluctuating slightly with lambda on idle."/>
<parameter id= "Tumble Valve Position Sensor Left" offset= "#0034" storagetype= "uint8" decimals= "3" bit= "8" byte= "6"
expr="[value]*2/100" metric="V" desc="Voltage generated by the tumble value position sensor."/>
<parameter id= "Air/Fuel Sensor #2 Current" offset= "#0043" storagetype= "uint8" decimals= "3" bit= "1" byte= "7"
expr="([value]-128)*125/1000" metric="mA" desc="Current generated by the Air/Fuel Sensor."/>
<parameter id= "Air/Fuel Sensor #1 Current" offset= "#0042" storagetype= "uint8" decimals= "3" bit= "2" byte= "7"
expr="([value]-128)*125/1000" metric="mA" desc="Current generated by the Air/Fuel Sensor."/>
<parameter id= "Intake OCV Current Left" offset= "#0041" storagetype= "uint8" decimals= "3" bit= "3" byte= "7" expr= "[value]*32" metric= "mA"
desc="Current generated by the Oil Control Valve solenoid."/>
<parameter id= "Intake OCV Current Right" offset= "#0040" storagetype= "uint8" decimals= "3" bit= "4" byte= "7" expr= "[value]*32"
metric="mA" desc="Current generated by the Oil Control Valve solenoid."/>
<parameter id= "Intake OCV Duty Left" offset= "#003F" storagetype= "uint8" decimals= "2" bit= "5" byte= "7" expr= "[value]*100/255"
metric="%"
desc="The Oil Control Valve controls the intake VVT advance angles. The|values are a duty %, indicating the proportion of time that the valves|are energised."/>
<parameter id= "Intake OCV Duty Right" offset= "#003E" storagetype= "uint8" decimals= "2" bit= "6" byte= "7" expr= "[value]*100/255"
metric="%"
desc="The Oil Control Valve controls the intake VVT advance angles. The|values are a duty %, indicating the proportion of time that the valves|are energised."/>
<parameter id= "Intake VVT Advance Angle Left" offset= "#003D" storagetype= "uint8" decimals= "0" bit= "7" byte= "7" expr= "([value]-50)"
metric="B "
desc="Degrees of intake camshaft advance applied. The higher the advance|angle, the earlier the intake valves open; this causes more intake|valve overlap which can help the engine to breathe more efficiently at|a particular RPM and load. It is normal to see small differences|between left and right sides of the engine, however, large continuous|differences may indicate a fault."/>
<parameter id= "Intake VVT Advance Angle Right" offset= "#003C" storagetype= "uint8" decimals= "0" bit= "8" byte= "7" expr= "([value]-50)"
metric="B "
desc="Degrees of intake camshaft advance applied. The higher the advance|angle, the earlier the intake valves open; this causes more intake|valve overlap which can help the engine to breathe more efficiently at|a particular RPM and load. It is normal to see small differences|between left and right sides of the engine, however, large continuous|differences may indicate a fault."/>
<parameter id= "Air/Fuel Adjustment Voltage" offset= "#00D3" storagetype= "uint8" decimals= "3" bit= "1" byte= "8" expr= "[value]*2/100"
metric="V" desc=""/>
<parameter id= "Rear O2 Heater Voltage" offset= "#00D2" storagetype= "uint8" decimals= "3" bit= "2" byte= "8" expr= "[value]*2/100"
metric="V" desc=""/>
<parameter id= "Air/Fuel Learning #3" offset= "#00D1" storagetype= "uint8" decimals= "2" bit= "3" byte= "8" expr= "([value]-128)*100/128"
metric="%"
desc="Fuel trim corrections made by the ECU while in closed loop. This value|is based on trends seen in the Air/Fuel Trim Immediate field.|Adjustments are made slower. The combined value of this field and the|Air/Fuel Trim Immediate field equal your total fuel trim. This|correction is not directly active when in open loop."/>
<parameter id= "Air/Fuel Correction #3" offset= "#00D0" storagetype= "uint8" decimals= "2" bit= "4" byte= "8" expr= "([value]-128)*100/128"
metric="%"
desc="Fuel trim corrections made by the ECU while in closed loop. This|value is updated most frequently. Adjustments are made based on the|values provided by the Front O2 Sensor. This correction is not active|when in open loop."/>
<parameter id= "Air/Fuel Sensor #2" offset= "#0047" storagetype= "uint8" decimals= "2" type= "afr" bit= "5" byte= "8" expr= "[value]/128"
metric="Lambda"
desc="Calculated Air/Fuel ratio based on the readings from the factory front|O2 sensor. The factory front O2 sensor is not a true wideband, and|typically loses accuracy at Air/Fuel ratios richer than 11.5:1. This|sensor is only used during closed loop fueling. A good value to|monitor for reference, but not one suggested to be used solely for|tuning."/>
<parameter id= "Air/Fuel Sensor #1" offset= "#0046" storagetype= "uint8" decimals= "2" type= "afr" bit= "6" byte= "8" expr= "[value]/128"
metric="Lambda"
desc="Calculated Air/Fuel ratio based on the readings from the factory front|O2 sensor. The factory front O2 sensor is not a true wideband, and|typically loses accuracy at Air/Fuel ratios richer than 11.5:1. This|sensor is only used during closed loop fueling. A good value to|monitor for reference, but not one suggested to be used solely for|tuning."/>
<parameter id= "Air/Fuel Sensor #2 Resistance" offset= "#0045" storagetype= "uint8" decimals= "3" bit= "7" byte= "8" expr= "[value]"
metric="Ohms" desc="Resistance measured at the Air/Fuel sensor."/>
<parameter id= "Air/Fuel Sensor #1 Resistance" offset= "#0044" storagetype= "uint8" decimals= "3" bit= "8" byte= "8" expr= "[value]"
metric="Ohms" desc="Resistance measured at the Air/Fuel sensor."/>
<parameter id= "Gear Position" offset= "#004A" storagetype= "uint8" decimals= "3" bit= "6" byte= "9" expr= "([value]+1)" metric= "gear"
desc=""/>
<parameter id= "Air/Fuel Sensor #2 Heater Current" offset= "#0054" storagetype= "uint8" decimals= "3" bit= "4" byte= "10" expr= "[value]/10"
metric="Amps" desc=""/>
<parameter id= "Air/Fuel Sensor #1 Heater Current" offset= "#0053" storagetype= "uint8" decimals= "3" bit= "5" byte= "10" expr= "[value]/10"
metric="Amps" desc=""/>
<parameter id= "Read Memory Signal" offset= "#0061" storagetype= "uint8" decimals= "0" type= "bool" bit= "5" byte= "12" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Test Mode Signal" offset= "#0061" storagetype= "uint8" decimals= "0" type= "bool" bit= "6" byte= "12" expr= "[value]"
metric="On/Off" desc="When test mode connector is connected."/>
<parameter id= "AT/MT Identification Signal" offset= "#0061" storagetype= "uint8" decimals= "0" type= "bool" bit= "7" byte= "12"
expr="[value]" metric="On/Off" desc=""/>
<parameter id= "A/C Switch Signal" offset= "#0062" storagetype= "uint8" decimals= "0" type= "bool" bit= "2" byte= "13" expr= "[value]"
metric="On/Off" desc="When air conditioning switch is turned ON."/>
<parameter id= "Power Steering Switch Signal" offset= "#0062" storagetype= "uint8" decimals= "0" type= "bool" bit= "3" byte= "13"
expr="[value]" metric="On/Off" desc="When power steering switch is entered."/>
<parameter id= "Ignition Switch Signal" offset= "#0062" storagetype= "uint8" decimals= "0" type= "bool" bit= "4" byte= "13" expr= "[value]"
metric="On/Off" desc="When ignition is turned to ON."/>
<parameter id= "Intercooler Auto-Wash Switch Signal" offset= "#0062" storagetype= "uint8" decimals= "0" type= "bool" bit= "5" byte= "13"
expr="[value]" metric="On/Off" desc=""/>
<parameter id= "Idle Switch Signal" offset= "#0062" storagetype= "uint8" decimals= "0" type= "bool" bit= "7" byte= "13" expr= "[value]"
metric="On/Off" desc="When idle switch signal is entered."/>
<parameter id= "Neutral Position Switch Signal" offset= "#0062" storagetype= "uint8" decimals= "0" type= "bool" bit= "8" byte= "13"
expr="[value]" metric="On/Off" desc="When neutral position signal is entered."/>
<parameter id= "Electrical Load Signal" offset= "#0063" storagetype= "uint8" decimals= "0" type= "bool" bit= "1" byte= "14" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Knock Signal #2" offset= "#0063" storagetype= "uint8" decimals= "0" type= "bool" bit= "2" byte= "14" expr= "[value]"
metric="On/Off"
desc="Knock sensor input. Knock signals occur extremely fast and may not|always be captured, it is suggested to rather watch the Knock|Correction value."/>
<parameter id= "Knock Signal #1" offset= "#0063" storagetype= "uint8" decimals= "0" type= "bool" bit= "3" byte= "14" expr= "[value]"
metric="On/Off"
desc="Knock sensor input. Knock signals occur extremely fast and may not|always be captured, it is suggested to rather watch the Knock|Correction value."/>
<parameter id= "Front O2 #2 Rich Signal" offset= "#0063" storagetype= "uint8" decimals= "0" type= "bool" bit= "4" byte= "14" expr= "[value]"
metric="On/Off" desc="When front O2 sensor mixture ratio is rich."/>
<parameter id= "Rear O2 Rich Signal" offset= "#0063" storagetype= "uint8" decimals= "0" type= "bool" bit= "5" byte= "14" expr= "[value]"
metric="On/Off" desc="When rear O2 sensor mixture ratio is rich."/>
<parameter id= "Front O2 Rich Signal" offset= "#0063" storagetype= "uint8" decimals= "0" type= "bool" bit= "6" byte= "14" expr= "[value]"
metric="On/Off" desc="When front O2 sensor mixture ratio is rich."/>
<parameter id= "Starter Switch Signal" offset= "#0063" storagetype= "uint8" decimals= "0" type= "bool" bit= "7" byte= "14" expr= "[value]"
metric="On/Off" desc="When starter switch signal is entered."/>
<parameter id= "Handle Switch" offset= "#0063" storagetype= "uint8" decimals= "0" type= "bool" bit= "8" byte= "14" expr= "[value]"
metric="RHD/LHD" desc="When the vehicle is LHD model."/>
<parameter id= "A/C Mid Pressure Switch" offset= "#0064" storagetype= "uint8" decimals= "0" type= "bool" bit= "1" byte= "15" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "A/C Lock Signal" offset= "#0064" storagetype= "uint8" decimals= "0" type= "bool" bit= "2" byte= "15" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Wiper Switch" offset= "#0064" storagetype= "uint8" decimals= "0" type= "bool" bit= "3" byte= "15" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Interior Light Switch" offset= "#0064" storagetype= "uint8" decimals= "0" type= "bool" bit= "4" byte= "15" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Blower Fan Switch" offset= "#0064" storagetype= "uint8" decimals= "0" type= "bool" bit= "5" byte= "15" expr= "[value]"
metric="On/Off" desc="When blower flan switch is turned ON."/>
<parameter id= "Rear Defogger Switch Signal" offset= "#0064" storagetype= "uint8" decimals= "0" type= "bool" bit= "6" byte= "15"
expr="[value]" metric="On/Off"
desc="When the rear window defogger is turned ON. This sensor is used to|initiate data logging to a .csv file."/>
<parameter id= "Camshaft Position Sensor Signal" offset= "#0064" storagetype= "uint8" decimals= "0" type= "bool" bit= "7" byte= "15"
expr="[value]" metric="On/Off" desc="When camshaft position sensor signal is entered."/>
<parameter id= "Crankshaft Position Sensor Signal" offset= "#0064" storagetype= "uint8" decimals= "0" type= "bool" bit= "8" byte= "15"
expr="[value]" metric="On/Off" desc="When crankshaft position sensor signal is entered"/>
<parameter id= "Blow-By Leak Connector" offset= "#0065" storagetype= "uint8" decimals= "0" type= "bool" bit= "1" byte= "16" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "CPC Solenoid Valve" offset= "#0065" storagetype= "uint8" decimals= "0" type= "bool" bit= "2" byte= "16" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Intercooler Auto-Wash Relay" offset= "#0065" storagetype= "uint8" decimals= "0" type= "bool" bit= "3" byte= "16"
expr="[value]" metric="On/Off" desc=""/>
<parameter id= "Fuel Pump Relay" offset= "#0065" storagetype= "uint8" decimals= "0" type= "bool" bit= "4" byte= "16" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Radiator Fan Relay #2" offset= "#0065" storagetype= "uint8" decimals= "0" type= "bool" bit= "5" byte= "16" expr= "[value]"
metric="On/Off" desc="When radiator sub fan relay is in function."/>
<parameter id= "Radiator Fan Relay #1" offset= "#0065" storagetype= "uint8" decimals= "0" type= "bool" bit= "6" byte= "16" expr= "[value]"
metric="On/Off" desc="When radiator sub fan relay is in function."/>
<parameter id= "Radiator Fan Relay #3" offset= "#0065" storagetype= "uint8" decimals= "0" type= "bool" bit= "7" byte= "16" expr= "[value]"
metric="On/Off" desc="When radiator sub fan relay is in function."/>
<parameter id= "A/C Compressor Signal" offset= "#0065" storagetype= "uint8" decimals= "0" type= "bool" bit= "8" byte= "16" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Assist Air Solenoid Valve" offset= "#0066" storagetype= "uint8" decimals= "0" type= "bool" bit= "1" byte= "17" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Power Steering Solenoid Valve" offset= "#0066" storagetype= "uint8" decimals= "0" type= "bool" bit= "2" byte= "17"
expr="[value]" metric="On/Off" desc=""/>
<parameter id= "Vent Solenoid Valve" offset= "#0066" storagetype= "uint8" decimals= "0" type= "bool" bit= "3" byte= "17" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Pressure Sources Change" offset= "#0066" storagetype= "uint8" decimals= "0" type= "bool" bit= "4" byte= "17" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Variable Intake Air Solenoid" offset= "#0066" storagetype= "uint8" decimals= "0" type= "bool" bit= "5" byte= "17"
expr="[value]" metric="On/Off" desc=""/>
<parameter id= "TGV Drive Signal" offset= "#0066" storagetype= "uint8" decimals= "0" type= "bool" bit= "6" byte= "17" expr= "[value]"
metric="On/Off" desc="Tumble Generator Valve Drive Signal. When TGV moves and valve opens."/>
<parameter id= "TGV Output Signal" offset= "#0066" storagetype= "uint8" decimals= "0" type= "bool" bit= "7" byte= "17" expr= "[value]"
metric="On/Off" desc="Tumble Generator Valve Output Signal. When TGV actuator signal is|entered."/>
<parameter id= "Fuel Pressure Control Solenoid Valve" offset= "#0066" storagetype= "uint8" decimals= "0" type= "bool" bit= "8" byte= "17"
expr="[value]" metric="On/Off" desc="When fuel pressure control solenoid valve is in function."/>
<parameter id= "Muffler Control" offset= "#0067" storagetype= "uint8" decimals= "0" type= "bool" bit= "1" byte= "18" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Intake Air Solenoid" offset= "#0067" storagetype= "uint8" decimals= "0" type= "bool" bit= "2" byte= "18" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Exhaust Gas Negative Pressure" offset= "#0067" storagetype= "uint8" decimals= "0" type= "bool" bit= "3" byte= "18"
expr="[value]" metric="On/Off" desc=""/>
<parameter id= "Exhaust Gas Positive Pressure" offset= "#0067" storagetype= "uint8" decimals= "0" type= "bool" bit= "4" byte= "18"
expr="[value]" metric="On/Off" desc=""/>
<parameter id= "TCS Relief Valve Solenoid" offset= "#0067" storagetype= "uint8" decimals= "0" type= "bool" bit= "5" byte= "18" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Relief Valve Solenoid #2" offset= "#0067" storagetype= "uint8" decimals= "0" type= "bool" bit= "6" byte= "18" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Relief Valve Solenoid #1" offset= "#0067" storagetype= "uint8" decimals= "0" type= "bool" bit= "7" byte= "18" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Tank Sensor Control Valve" offset= "#0067" storagetype= "uint8" decimals= "0" type= "bool" bit= "8" byte= "18" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Request Torque Down VDC" offset= "#0068" storagetype= "uint8" decimals= "0" type= "bool" bit= "1" byte= "19" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Ban Of Torque Down" offset= "#0068" storagetype= "uint8" decimals= "0" type= "bool" bit= "2" byte= "19" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Fuel Cut Signal From AT" offset= "#0068" storagetype= "uint8" decimals= "0" type= "bool" bit= "3" byte= "19" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Retard Signal From AT" offset= "#0068" storagetype= "uint8" decimals= "0" type= "bool" bit= "4" byte= "19" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "AET Signal" offset= "#0069" storagetype= "uint8" decimals= "0" type= "bool" bit= "1" byte= "20" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "AT Coop. Rich Spike Signal" offset= "#0069" storagetype= "uint8" decimals= "0" type= "bool" bit= "2" byte= "20"
expr="[value]" metric="On/Off" desc=""/>
<parameter id= "AT Coop. Lean Burn Signal" offset= "#0069" storagetype= "uint8" decimals= "0" type= "bool" bit= "3" byte= "20" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "AT Coop. Lock Up Signal" offset= "#0069" storagetype= "uint8" decimals= "0" type= "bool" bit= "4" byte= "20" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "EAM Signal" offset= "#0069" storagetype= "uint8" decimals= "0" type= "bool" bit= "5" byte= "20" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Torque Permission Signal" offset= "#0069" storagetype= "uint8" decimals= "0" type= "bool" bit= "6" byte= "20" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Torque Control Signal #2" offset= "#0069" storagetype= "uint8" decimals= "0" type= "bool" bit= "7" byte= "20" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Torque Control Signal #1" offset= "#0069" storagetype= "uint8" decimals= "0" type= "bool" bit= "8" byte= "20" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Throttle Motor Voltage" offset= "#00FB" storagetype= "uint8" decimals= "3" bit= "5" byte= "31" expr= "[value]*8/100"
metric="volts" desc=""/>
<parameter id= "Throttle Motor Duty" offset= "#00FA" storagetype= "uint8" decimals= "2" bit= "6" byte= "31" expr= "([value]-128)*100/128"
metric="%" desc=""/>
<parameter id= "Exhaust Gas Temperature" offset= "#0106" storagetype= "uint8" decimals= "2" type= "temp" bit= "2" byte= "33"
expr="([value]+40)*5" metric="B C"
desc="Exhaust gas temperature on vehicles equipped with this sensor located|in the uppipe before the turbocharger."/>
<parameter id= "Fuel Pressure (High)" offset= "#0105" storagetype= "uint8" decimals= "3" bit= "3" byte= "33" expr= "[value]*4/100"
metric="MPa" desc=""/>
<parameter id= "Brake Booster Pressure" offset= "#0104" storagetype= "uint8" decimals= "3" type= "press" bit= "4" byte= "33"
expr="[value]*37/255" metric="PSI" desc=""/>
<parameter id= "Main Accelerator Sensor" offset= "#0103" storagetype= "uint8" decimals= "3" bit= "5" byte= "33" expr= "[value]*2/100"
metric="volts" desc=""/>
<parameter id= "Sub Accelerator Sensor" offset= "#0102" storagetype= "uint8" decimals= "3" bit= "6" byte= "33" expr= "[value]*2/100"
metric="volts" desc=""/>
<parameter id= "Main Throttle Sensor" offset= "#0101" storagetype= "uint8" decimals= "3" bit= "7" byte= "33" expr= "[value]*2/100"
metric="volts" desc=""/>
<parameter id= "Sub Throttle Sensor" offset= "#0100" storagetype= "uint8" decimals= "3" bit= "8" byte= "33" expr= "[value]*2/100"
metric="volts" desc=""/>
<parameter id= "Memorized Cruise Speed" offset= "#010A" storagetype= "uint8" decimals= "0" type= "speed" bit= "6" byte= "34" expr= "[value]"
metric="KPH" desc=""/>
<parameter id= "SCV Step" offset= "#0109" storagetype= "uint8" decimals= "0" bit= "7" byte= "34" expr= "[value]" metric= "steps" desc= "" />
<parameter id= "Cold Start Injector" offset= "#0108" storagetype= "uint8" decimals= "0" type= "inj" bit= "8" byte= "34"
expr="[value]*256/1000" metric="ms" desc=""/>
<parameter id= "Exhaust OCV Current Left" offset= "#011D" storagetype= "uint8" decimals= "3" bit= "3" byte= "36" expr= "[value]*32"
metric="mA" desc="Current generated by the Oil Control Valve solenoid."/>
<parameter id= "Exhaust OCV Current Right" offset= "#011C" storagetype= "uint8" decimals= "3" bit= "4" byte= "36" expr= "[value]*32"
metric="mA" desc="Current generated by the Oil Control Valve solenoid."/>
<parameter id= "Exhaust OCV Duty Left" offset= "#011B" storagetype= "uint8" decimals= "2" bit= "5" byte= "36" expr= "[value]*100/255"
metric="%"
desc="The Oil Control Valve controls the exhaust VVT advance angles. The|values are a duty %, indicating the proportion of time that the valves|are energised."/>
<parameter id= "Exhaust OCV Duty Right" offset= "#011A" storagetype= "uint8" decimals= "2" bit= "6" byte= "36" expr= "[value]*100/255"
metric="%"
desc="The Oil Control Valve controls the exhaust VVT advance angles. The|values are a duty %, indicating the proportion of time that the valves|are energised."/>
<parameter id= "Exhaust VVT Advance Angle Left" offset= "#0119" storagetype= "uint8" decimals= "2" bit= "7" byte= "36" expr= "([value]-50)"
metric="B "
desc="Degrees of intake camshaft advance applied. The higher the advance|angle, the earlier the exhaust valves open; this causes more exhaust|valve overlap which can help the engine to breathe more efficiently at|a particular RPM and load. It is normal to see small differences|between left and right sides of the engine, however, large continuous|differences may indicate a fault."/>
<parameter id= "Exhaust VVT Advance Angle Right" offset= "#0118" storagetype= "uint8" decimals= "2" bit= "8" byte= "36" expr= "([value]-50)"
metric="B "
desc="Degrees of intake camshaft advance applied. The higher the advance|angle, the earlier the exhaust valves open; this causes more exhaust|valve overlap which can help the engine to breathe more efficiently at|a particular RPM and load. It is normal to see small differences|between left and right sides of the engine, however, large continuous|differences may indicate a fault."/>
<parameter id= "ETC Motor Relay" offset= "#0120" storagetype= "uint8" decimals= "0" type= "bool" bit= "7" byte= "37" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Accelerator Switch" offset= "#0121" storagetype= "uint8" decimals= "0" type= "bool" bit= "2" byte= "38" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Brake Switch" offset= "#0121" storagetype= "uint8" decimals= "0" type= "bool" bit= "4" byte= "38" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Resume/Accelerate Switch" offset= "#0121" storagetype= "uint8" decimals= "0" type= "bool" bit= "5" byte= "38" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Set/Coast Switch" offset= "#0121" storagetype= "uint8" decimals= "0" type= "bool" bit= "6" byte= "38" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Stop Light Switch" offset= "#0121" storagetype= "uint8" decimals= "0" type= "bool" bit= "7" byte= "38" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Clutch Switch" offset= "#0121" storagetype= "uint8" decimals= "0" type= "bool" bit= "8" byte= "38" expr= "[value]"
metric="On/Off" desc=""/>
<parameter id= "Roughness Monitor Cylinder #4" offset= "#00D9" storagetype= "uint8" decimals= "0" bit= "5" byte= "48" expr= "[value]"
metric="?" desc=""/>
<parameter id= "Roughness Monitor Cylinder #3" offset= "#00D8" storagetype= "uint8" decimals= "0" bit= "6" byte= "48" expr= "[value]"
metric="?" desc=""/>
<parameter id= "Roughness Monitor Cylinder #2" offset= "#00CF" storagetype= "uint8" decimals= "0" bit= "7" byte= "48" expr= "[value]"
metric="?" desc=""/>
<parameter id= "Roughness Monitor Cylinder #1" offset= "#00CE" storagetype= "uint8" decimals= "0" bit= "8" byte= "48" expr= "[value]"
metric="?" desc=""/>
</ecu>
<ecu id= "base" name= "SSM 16 base" type= "ssmbase16" include= "ssmbase" >
<parameter id= "Advance Multiplier" offset= "#20124" storagetype= "uint8" decimals= "0" expr= "[value]" metric= ""
desc="Value used to represent the knock tendency of the engine. A higher|value represents better performance for the given mapping and|conditions. This value ranges between 0 (worst) and 16 (best). This|value is used in determining the about of Knock Correction ignition|advance/retard applied to the base ignition timing map.">
<alt id= "Advance Multiplier (20118)" offset= "#20118" />
<alt id= "Advance Multiplier (20120)" offset= "#20120" />
<alt id= "Advance Multiplier (20124)" offset= "#20124" />
<alt id= "Advance Multiplier (20128)" offset= "#20128" />
<alt id= "Advance Multiplier (20168)" offset= "#20168" />
</parameter>
<parameter id= "Engine Load (RAM)" offset= "#21975" storagetype= "uint8" decimals= "2" expr= "[value]/32" metric= "g"
desc="Calculated engine load based on a number of conditions such as MAF|sensor reading, engine coolant temp, etc. This represents how hard|the engine is being asked to work. Load does not simply mean boost.|This value is used as an axis reference point on many of the ECU maps.">
<alt id= "Engine Load (2009A)" offset= "#2009A" />
<alt id= "Engine Load (200B4)" offset= "#200B4" />
<alt id= "Engine Load (200BE)" offset= "#200BE" />
<alt id= "Engine Load (200D8)" offset= "#200D8" />
<alt id= "Engine Load (200EE)" offset= "#200EE" />
<alt id= "Engine Load (200F2)" offset= "#200F2" />
<alt id= "Engine Load (200F4)" offset= "#200F4" />
<alt id= "Engine Load (21847)" offset= "#21847" />
<alt id= "Engine Load (218BF)" offset= "#218BF" />
<alt id= "Engine Load (218C1)" offset= "#218C1" />
<alt id= "Engine Load (21975)" offset= "#21975" />
<alt id= "Engine Load (219BD)" offset= "#219BD" />
</parameter>
</ecu>
<ecu id= "base" name= "SSM 32 base" type= "ssmbase32" include= "ssmbase" >
<parameter id= "Advance Multiplier" offset= "#802244" storagetype= "uint8" decimals= "0" expr= "[value]" metric= ""
desc="Value used to represent the knock tendency of the engine. A higher|value represents better performance for the given mapping and|conditions. This value ranges between 0 (worst) and 16 (best). This|value is used in determining the about of Knock Correction ignition|advance/retard applied to the base ignition timing map.">
<alt id= "Advance Multiplier (802244)" offset= "#802244" storagetype= "uint8" />
<alt id= "Advance Multiplier (80224A)" offset= "#80224A" storagetype= "uint8" />
<alt id= "Advance Multiplier (80224E)" offset= "#80224E" storagetype= "uint8" />
<alt id= "Advance Multiplier (80225E)" offset= "#80225E" storagetype= "uint8" />
<alt id= "Advance Multiplier (FF83CC)" offset= "#FF83CC" storagetype= "float" />
<alt id= "Advance Multiplier (FF8550)" offset= "#FF8550" storagetype= "float" />
<alt id= "Advance Multiplier (FF8228)" offset= "#FF8228" storagetype= "float" />
<alt id= "Advance Multiplier (FF822C)" offset= "#FF822C" storagetype= "float" />
<alt id= "Advance Multiplier (FF8260)" offset= "#FF8260" storagetype= "float" />
<alt id= "Advance Multiplier (FF850C)" offset= "#FF850C" storagetype= "float" />
<alt id= "Advance Multiplier (FF2664)" offset= "#FF2664" storagetype= "float" />
<alt id= "Advance Multiplier (FF2688)" offset= "#FF2688" storagetype= "float" />
<alt id= "Advance Multiplier (FF267C)" offset= "#FF267C" storagetype= "float" />
<alt id= "Advance Multiplier (FF2588)" offset= "#FF2588" storagetype= "float" />
<alt id= "Advance Multiplier (FF824C)" offset= "#FF824C" storagetype= "float" />
<alt id= "Advance Multiplier (FF83AC)" offset= "#FF83AC" storagetype= "float" />
<alt id= "Advance Multiplier (FF2914)" offset= "#FF2914" storagetype= "float" />
<alt id= "Advance Multiplier (FF2B3C)" offset= "#FF2B3C" storagetype= "float" />
<alt id= "Advance Multiplier (FF2674)" offset= "#FF2674" storagetype= "float" />
<alt id= "Advance Multiplier (FF2570)" offset= "#FF2570" storagetype= "float" />
<alt id= "Advance Multiplier (FF854C)" offset= "#FF854C" storagetype= "float" />
</parameter>
<parameter id= "Engine Load (RAM)" offset= "#801308" storagetype= "uint16" decimals= "2" expr= "[value]/256" metric= ""
desc="Calculated engine load based on a number of conditions such as MAF|sensor reading, engine coolant temp, etc. This represents how hard|the engine is being asked to work. Load does not simply mean boost.|This value is used as an axis reference point on many of the ECU maps.">
<alt id= "Engine Load (801308)" offset= "#801308" storagetype= "uint16" />
<alt id= "Engine Load (801014)" offset= "#801014" storagetype= "uint16" />
<alt id= "Engine Load (8010F6)" offset= "#8010F6" storagetype= "uint16" />
<alt id= "Engine Load (80101A)" offset= "#80101A" storagetype= "uint16" />
<alt id= "Engine Load (FFA41C)" offset= "#FFA41C" storagetype= "float" />
<alt id= "Engine Load (FFA6AC)" offset= "#FFA6AC" storagetype= "float" />
<alt id= "Engine Load (FFA6FC)" offset= "#FFA6FC" storagetype= "float" />
<alt id= "Engine Load (FFB0E0)" offset= "#FFB0E0" storagetype= "float" />
<alt id= "Engine Load (FFA750)" offset= "#FFA750" storagetype= "float" />
<alt id= "Engine Load (FFA770)" offset= "#FFA770" storagetype= "float" />
<alt id= "Engine Load (FFB358)" offset= "#FFB358" storagetype= "float" />
<alt id= "Engine Load (FFB2C4)" offset= "#FFB2C4" storagetype= "float" />
<alt id= "Engine Load (FF5030)" offset= "#FF5030" storagetype= "float" />
<alt id= "Engine Load (FF50B0)" offset= "#FF50B0" storagetype= "float" />
<alt id= "Engine Load (FFA648)" offset= "#FFA648" storagetype= "float" />
<alt id= "Engine Load (FFA664)" offset= "#FFA664" storagetype= "float" />
<alt id= "Engine Load (FF4F48)" offset= "#FF4F48" storagetype= "float" />
<alt id= "Engine Load (FFB3D0)" offset= "#FFB3D0" storagetype= "float" />
<alt id= "Engine Load (FFA818)" offset= "#FFA818" storagetype= "float" />
<alt id= "Engine Load (FF554C)" offset= "#FF554C" storagetype= "float" />
<alt id= "Engine Load (FF543C)" offset= "#FF543C" storagetype= "float" />
<alt id= "Engine Load (FFB438)" offset= "#FFB438" storagetype= "float" />
<alt id= "Engine Load (FF6694)" offset= "#FF6694" storagetype= "float" />
<alt id= "Engine Load (FF689C)" offset= "#FF689C" storagetype= "float" />
<alt id= "Engine Load (FF684C)" offset= "#FF684C" storagetype= "float" />
<alt id= "Engine Load (FF6848)" offset= "#FF6848" storagetype= "float" />
<alt id= "Engine Load (FF5034)" offset= "#FF5034" storagetype= "float" />
<alt id= "Engine Load (FF4F58)" offset= "#FF4F58" storagetype= "float" />
<alt id= "Engine Load (FF508C)" offset= "#FF508C" storagetype= "float" />
</parameter>
</ecu>
<ecu id= "1644500305" name= "MY99/00 Impreza 2.0 Turbo/WRX/GT (EURO)" type= "AE800" include= "ssmbase16" />
<ecu id= "1644500405" name= "MY99/00 Impreza 2.0 Turbo/WRX/GT (EURO)" type= "AE801" include= "ssmbase16" />
<ecu id= "1644500505" name= "MY99/00 Impreza 2.0 Turbo/WRX/GT (EURO)" type= "AE802" include= "ssmbase16" />
<ecu id= "16445005FF" name= "MY99/00 Impreza 2.0 Turbo/WRX/GT (EURO)" type= "AE802b" include= "ssmbase16" />
<ecu id= "1604690405" name= "MY99/00 Impreza 2.0 STI (JDM)" type= "AF040" include= "ssmbase16" />
<ecu id= "1604690505" name= "MY99/00 Impreza 2.0 STI (JDM)" type= "AF041" include= "ssmbase16" />
<ecu id= "1604690605" name= "Impreza 2.0 P1 (JDM)" type= "AG340" include= "ssmbase" />
<ecu id= "1B44580405" name= "MY01/02 Impreza 2.0 WRX (EURO)" type= "AF530-7554" include= "ssmbase16" />
<ecu id= "1B44580505" name= "MY01/02 Impreza 2.0 WRX (EURO)" type= "AF531" include= "ssmbase16" />
<ecu id= "2944594105" name= "MY01/02 Impreza 2.0 STI Type UK (EURO)" type= "AG820-2591" include= "ssmbase16" />
<ecu id= "1842100705" name= "MY02 Legacy 2.5 GX (EURO)" type= "" include= "ssmbase" />
<ecu id= "1844100805" name= "MY02 Legacy 2.0 GL (EURO)" type= "" include= "ssmbase" />
<ecu id= "0D04680805" name= "Legacy 2.0 B4 Twin-Turbo (JDM)" type= "AD983" include= "ssmbase16" />
<ecu id= "1944580505" name= "MY00 Forester 2.0 Turbo S/GT (EURO)" type= "AG050" include= "ssmbase16" />
<ecu id= "2344100805" name= "MY02 Forester 2.0 GLS (EURO)" type= "" include= "ssmbase16" />
<ecu id= "1B14400505" name= "MY01/02 Impreza 2.0 WRX (US)" type= "AF423" include= "ssmbase16" />
<ecu id= "1B14400305" name= "MY01/02 Impreza 2.0 WRX (US)" type= "AF411" include= "ssmbase16" />
<ecu id= "1B14400405" name= "MY01/02 Impreza 2.0 WRX" type= "AF422" include= "ssmbase16" />
<ecu id= "1B04490605" name= "MY01/02 Impreza 2.0 STI (JDM)" type= "AF481" include= "ssmbase16" />
<ecu id= "1B04490205" name= "MY01/02 Impreza 2.0 STI (JDM)" type= "AF480-7542" include= "ssmbase16" />
<ecu id= "2344500405" name= "MY02 Forester 2.0 Turbo S/GT Auto (EURO)" type= "AG200" include= "ssmbase16" />
<ecu id= "1E12" name= "Impreza 2.5 RS (US)" type= "AF581" include= "ssmbase" />
<ecu id= "1B04490405" name= "MY01/02 Impreza 2.0 STI (JDM)" type= "AF480-7541" include= "ssmbase16" />
<ecu id= "2954594105" name= "MY02 Impreza 2.0 STI (AUS)" type= "AH180-2581" include= "ssmbase16" />
<ecu id= "1B54500505" name= "MY01 Impreza 2.0 WRX (AUS)" type= "AH570" include= "ssmbase16" />
<ecu id= "1B44580305" name= "MY01/02 Impreza 2.0 WRX (EURO)" type= "AF530-7552" include= "ssmbase16" />
<ecu id= "1B44100705" name= "MY01/02 Impreza 2.0 GX (EURO)" type= "AF633" include= "ssmbase" />
<ecu id= "1B54500405" name= "MY01 Impreza 2.0 WRX (AUS)" type= "AF730-7574" include= "ssmbase16" />
<ecu id= "1944540505" name= "MY00 Forester 2.0 Turbo S/GT Auto (EURO)" type= "AE901-921" include= "ssmbase16" />
<ecu id= "2654786105" name= "MY02 Legacy 2.0 B4 Twin-Turbo (AUS)" type= "AG850-3382" include= "ssmbase16" />
<ecu id= "1844100605" name= "MY01 Legacy 2.0 Auto (EURO)" type= "AG180" include= "ssmbase" />
<ecu id= "1644100505" name= "Impreza 2.0 (EURO)" type= "AF671" include= "ssmbase" />
<ecu id= "1954540505" name= "MY00 Forester 2.0 Turbo S/GT Auto (EURO)" type= "AF261" include= "ssmbase16" />
<ecu id= "1604680405" name= "Impreza 2.0 WRX Type RA (JDM)" type= "AE481-2000" include= "ssmbase16" />
<ecu id= "2A44506005" name= "MY03 Forester 2.0 Turbo S/GT (EURO)" type= "AG580-1361" include= "ssmbase16" />
<ecu id= "2A44104305" name= "MY03 Forester 2.0 NA (EURO)" type= "AG600-2000" include= "ssmbase16" />
<ecu id= "1844100805" name= "MY03 Legacy 2.0 GX (EURO)" type= "" include= "ssmbase" />
<ecu id= "264A354005" name= "MY03 Legacy 3.0 Outback (EURO)" type= "" include= "ssmbase" />
<ecu id= "29044A4105" name= "MY01/02 Impreza 2.0 STI Type RA (JDM)" type= "AG970" include= "ssmbase16" />
<ecu id= "1954580505" name= "MY00 Forester 2.0 Turbo S/GT (AUS)" type= "AG060" include= "ssmbase16" />
<ecu id= "2354500405" name= "MY01 Forester 2.0 Turbo S/GT Auto (AUS)" type= "AG540" include= "ssmbase16" />
<ecu id= "2944593105" name= "MY01/02 Impreza 2.0 STI Type UK (EURO)" type= "AG820-090" include= "ssmbase16" />
<ecu id= "2954593105" name= "Impreza 2.0 STI (AUS)" type= "AH180-2580" include= "ssmbase16" />
<ecu id= "1B04400505" name= "MY01/02 Impreza 2.0 WRX (JDM)" type= "AF471-7085" include= "ssmbase16" />
<ecu id= "3614486105" name= "MY03 Impreza 2.0 WRX (US)" type= "AJ030-5692" include= "ssmbase16" />
<ecu id= "1B14400605" name= "MY01/02 Impreza 2.0 WRX (US)" type= "AF424-7066" include= "ssmbase16" />
<ecu id= "1604400305" name= "MY99/00 Impreza 2.0 WRX (JDM)" type= "AE490" include= "ssmbase16" />
<ecu id= "1604400405" name= "MY99/00 Impreza 2.0 WRX (JDM)" type= "AE491" include= "ssmbase16" />
<ecu id= "1612040605" name= "Impreza 2.5 RS (US)" type= "AF581b" include= "ssmbase" />
<ecu id= "29044A7105" name= "MY01/02 Impreza 2.0 STI Type RA (JDM)" type= "AG971" include= "ssmbase16" />
<ecu id= "3614446105" name= "MY03 Impreza 2.0 WRX Auto (US)" type= "AJ040-5702" include= "ssmbase16" />
<ecu id= "2E44584005" name= "MY03 Impreza 2.0 WRX (EURO)" type= "AH750-5140" include= "ssmbase16" />
<ecu id= "2E44594005" name= "MY03 Impreza 2.0 STI Type UK (EURO)" type= "AH990-5511" include= "ssmbase16" />
<ecu id= "1B14400105" name= "MY01 Impreza 2.0 WRX (US)" type= "AF420" include= "ssmbase16" />
<ecu id= "1E12080805" name= "MY01 Impreza 2.5 RS (US)" type= "" include= "ssmbase" />
<ecu id= "1B04400405" name= "MY01/02 Impreza 2.0 WRX (JDM)" type= "AF470-7084" include= "ssmbase16" />
<ecu id= "2904495005" name= "MY03 Impreza 2.0 STI (JDM)" type= "AH190-3771" include= "ssmbase16" />
<ecu id= "2E54504105" name= "MY03 Impreza 2.0 WRX (AUS)" type= "AF770" include= "ssmbase16" />
<ecu id= "2944596105" name= "MY01/02 Impreza 2.0 STI Type UK (EURO)" type= "AG820-821" include= "ssmbase16" />
<ecu id= "2E04494005" name= "MY03 Impreza 2.0 STI (JDM)" type= "AH580-5121" include= "ssmbase16" />
<ecu id= "2E44594105" name= "MY03 Impreza 2.0 STI Type UK (EURO)" type= "AH990-5512" include= "ssmbase16" />
<ecu id= "2E54594105" name= "MY03 Impreza 2.0 STI (AUS)" type= "AJ000-5521" include= "ssmbase16" />
<ecu id= "184A350205" name= "MY00 Legacy 3.0 H6 (EURO)" type= "AF992" include= "ssmbase" />
<ecu id= "2952100705" name= "MY01 Impreza 2.5 (AUS)" type= "AG710" include= "ssmbase" />
<ecu id= "0D42100405" name= "MY00 Legacy 2.5 RX (EURO)" type= "AG130" include= "ssmbase" />
<ecu id= "1904400505" name= "MY01 Forester 2.0 STB (JDM)" type= "AG380" include= "ssmbase" />
<ecu id= "0D04440805" name= "Legacy 2.0 B4 Twin-Turbo (JDM)" type= "AD971" include= "ssmbase16" />
<ecu id= "2604686305" name= "MY02 Legacy 2.0 B4 Twin-Turbo (JDM)" type= "AG441" include= "ssmbase16" />
<ecu id= "29046B6005" name= "Impreza 2.0 STI S202 (JDM)" type= "S202" include= "ssmbase16" />
<ecu id= "3614486205" name= "MY03 Impreza 2.0 WRX (US)" type= "AJ031" include= "ssmbase16" />
<ecu id= "2E44584105" name= "MY03 Impreza 2.0 WRX (EURO)" type= "AH750-5141" include= "ssmbase16" />
<ecu id= "1B04490505" name= "MY01/02 Impreza 2.0 STI (JDM)" type= "AF481-7545" include= "ssmbase16" />
<ecu id= "2604686505" name= "MY03 Legacy 2.0 B4 Twin-Turbo (JDM)" type= "AG443" include= "ssmbase16" />
<ecu id= "1954500405" name= "MY99 Forester 2.0 Turbo S/GT (AUS)" type= "AF260-8721" include= "ssmbase16" />
<ecu id= "2A52186005" name= "MY02 Forester 2.5 (AUS)" type= "AF621-2523" include= "ssmbase" />
<ecu id= "2354500405" name= "MY02 Forester 2.0 (AUS)" type= "AG540-0243" include= "ssmbase" />
<ecu id= "1B04490805" name= "MY01/02 Impreza 2.0 STI (JDM)" type= "AF482-7548" include= "ssmbase16" />
<ecu id= "2E044A6005" name= "MY03 Impreza 2.0 STI Spec C (JDM)" type= "AH591-5132" include= "ssmbase16" />
<ecu id= "2954546005" name= "MY02 Impreza 2.0 WRX (AUS)" type= "AF720-7566" include= "ssmbase16" />
<ecu id= "2E04496005" name= "MY03 Impreza 2.0 STI (JDM)" type= "AH581-5122" include= "ssmbase16" />
<ecu id= "0D04680905" name= "MY99 Legacy 2.0 Twin-Turbo (JDM)" type= "AD984" include= "ssmbase16" />
<ecu id= "0D04460305" name= "MY99 Legacy 2.0 B4 RSK (JDM)" type= "AF181" include= "ssmbase16" />
<ecu id= "2E12495106" name= "MY04 Impreza 2.5 STI (US)" type= "AJ241" include= "ssmbase32" />
<ecu id= "1804680205" name= "MY99 Legacy 2.0 Twin-Turbo (JDM)" type= "AG302" include= "ssmbase16" />
<ecu id= "1644500205" name= "MY99/00 Impreza 2.0 Turbo/WRX/GT (EURO)" type= "AE800b" include= "ssmbase16" />
<ecu id= "2E14486006" name= "MY04 Impreza 2.0 WRX (US)" type= "AH791" include= "ssmbase16" />
<ecu id= "3152504006" name= "MY04 Forester 2.5 XT (AUS)" type= "AH710-5401" include= "ssmbase16" />
<ecu id= "3614446205" name= "MY03 Impreza 2.0 WRX Auto (US)" type= "AJ041" include= "ssmbase16" />
<ecu id= "1B04400605" name= "MY01/02 Impreza 2.0 WRX (JDM)" type= "AF471-7086" include= "ssmbase16" />
<ecu id= "2A44506105" name= "MY03 Forester 2.0 Turbo S/GT Turbo (EURO)" type= "AG580-1362" include= "ssmbase16" />
<ecu id= "2E14446006" name= "MY04 Impreza 2.0 WRX Auto (US)" type= "AH801" include= "ssmbase16" />
<ecu id= "2944596005" name= "MY01/02 Impreza 2.0 STI Type UK (EURO)" type= "AG820" include= "ssmbase16" />
<ecu id= "1604680305" name= "Impreza 2.0 WRX Type RA (JDM)" type= "AE481" include= "ssmbase16" />
<ecu id= "2F54504006" name= "MY04 Legacy 2.0 GT (AUS)" type= "AH130" include= "ssmbase" />
<ecu id= "2F5A354106" name= "MY04 Legacy 3.0 H6 VDC (AUS)" type= "AJ230-7430" include= "ssmbase" />
<ecu id= "2F421A4106" name= "MY03 Legacy 2.5 (EURO)" type= "AH850" include= "ssmbase" />
<ecu id= "2F4A344106" name= "MY03 Legacy 3.0 H6 (EURO)" type= "AH620" include= "ssmbase" />
<ecu id= "2F44104206" name= "MY03 Legacy 2.0 (EURO)" type= "AH840" include= "ssmbase" />
<ecu id= "0D42100305" name= "MY99 Legacy 2.5 (EURO)" type= "AE151" include= "ssmbase" />
<ecu id= "2604686205" name= "MY02 Legacy 2.0 B4 Twin-Turbo (JDM)" type= "AG440-0983" include= "ssmbase16" />
<ecu id= "3144504006" name= "MY03 Forester 2.0 XT Turbo (EURO)" type= "AH690-5380" include= "ssmbase16" />
<ecu id= "1B46100705" name= "MY01/02 Impreza 1.6 (EURO)" type= "AG180" include= "ssmbase" />
<ecu id= "1844100B05" name= "MY02 Legacy 2.0 (EURO)" type= "AG660" include= "ssmbase" />
<ecu id= "2E44586005" name= "MY03 Impreza 2.0 WRX (EURO)" type= "AH751-5142" include= "ssmbase16" />
<ecu id= "2E14486106" name= "MY04 Impreza 2.0 WRX (US)" type= "AH792-5183" include= "ssmbase16" />
<ecu id= "1B14400705" name= "MY01/02 Impreza 2.0 WRX (US)" type= "AF425" include= "ssmbase16" />
<ecu id= "2E44596105" name= "MY03 Impreza 2.0 STI Type UK (EURO)" type= "AH992-5513" include= "ssmbase16" />
<ecu id= "2E14446106" name= "MY04 Impreza 2.0 WRX Auto (US)" type= "AH802" include= "ssmbase16" />
<ecu id= "2E12495206" name= "MY04 Impreza 2.5 STI (US)" type= "AJ242" include= "ssmbase32" />
<ecu id= "1944500405" name= "MY00 Forester 2.0 Turbo S/GT Auto (EURO)" type= "AE900-920" include= "ssmbase16" />
<ecu id= "2604446305" name= "MY02 Legacy 2.0 B4 Twin-Turbo (JDM)" type= "AG451-0995" include= "ssmbase16" />
<ecu id= "29044B6005" name= "MY01/02 Impreza 2.0 STI Type RA (JDM)" type= "AH970-5340" include= "ssmbase16" />
<ecu id= "2EA4584004" name= "MY04 Impreza 2.0 WRX (US)" type= "AH760-5150" include= "ssmbase16" />
<ecu id= "3112485106" name= "MY03 Forester 2.5 XT Turbo (US)" type= "AJ470-7312" include= "ssmbase32" />
<ecu id= "2F4A356006" name= "MY04 Legacy 3.0 Auto (EURO)" type= "AJ220-7423" include= "ssmbase" />
<ecu id= "2F42166106" name= "MY04 Legacy 2.5 Auto (EURO)" type= "AJ670-8332" include= "ssmbase" />
<ecu id= "2E044A3005" name= "MY03 Impreza 2.0 STI Spec C (JDM)" type= "AH590-5130" include= "ssmbase16" />
<ecu id= "1B04400205" name= "MY01/02 Impreza 2.0 WRX (JDM)" type= "AF460-7072" include= "ssmbase16" />
<ecu id= "1E12" name= "Impreza 2.5 RS (US)" type= "AF584" include= "ssmbase" />
<ecu id= "2F54505106" name= "MY04 Legacy 2.0 GT (AUS)" type= "AH131-5894" include= "ssmbase16" />
<ecu id= "3112405106" name= "MY03 Forester 2.5 XT Turbo (US)" type= "AH700-5392" include= "ssmbase32" />
<ecu id= "0D04680705" name= "Legacy 2.0 B4 Twin-Turbo (JDM)" type= "AD981" include= "ssmbase16" />
<ecu id= "2E445961EC" name= "Impreza 2.0 Prodrive WR1 (EURO)" type= "WR1" include= "ssmbase16" />
<ecu id= "3A54584005" name= "MY04 Impreza 2.0 WRX (AUS)" type= "AJ420-7550" include= "ssmbase16" />
<ecu id= "2904485005" name= "MY03 Impreza 2.0 WRX (JDM)" type= "AH200" include= "ssmbase16" />
<ecu id= "3614486305" name= "MY03 Impreza 2.0 WRX (US)" type= "AJ052-5694" include= "ssmbase16" />
<ecu id= "2654784005" name= "MY02 Legacy 2.0 B4 Twin-Turbo (AUS)" type= "AG850-3380" include= "ssmbase16" />
<ecu id= "2E044A6005" name= "MY03 Impreza 2.0 STI Spec C (JDM)" type= "AH590-5132" include= "ssmbase16" />
<ecu id= "2A04446305" name= "MY03 Forester 2.0 Turbo (JDM)" type= "AG572-1355" include= "ssmbase16" />
<ecu id= "2F5A356006" name= "MY04 Legacy 3.0 H6 VDC (AUS)" type= "AJ230-7431" include= "ssmbase" />
<ecu id= "2E044A4005" name= "MY03 Impreza 2.0 STI Spec C (JDM)" type= "AH590-076" include= "ssmbase16" />
<ecu id= "2E14486206" name= "MY04 Impreza 2.0 WRX (US)" type= "AH793-5184" include= "ssmbase16" />
<ecu id= "1904400405" name= "MY01 Forester 2.0 STB (JDM)" type= "AG830-8713" include= "ssmbase16" />
<ecu id= "2F04785006" name= "MY04 Legacy 2.0 GTB (JDM)" type= "AH110-5644" include= "ssmbase16" />
<ecu id= "2F04785206" name= "MY04 Legacy 2.0 GTB (JDM)" type= "AH110-5646" include= "ssmbase16" />
<ecu id= "3D12594006" name= "MY05 Impreza 2.5 STI (US)" type= "AJ930-8791" include= "ssmbase32" />
<ecu id= "2E12493006" name= "MY04 Impreza 2.5 STI (US)" type= "AJ241" include= "ssmbase32" />
<ecu id= "2F04505106" name= "MY04 Legacy 2.0 GT (JDM)" type= "AH121-5885" include= "ssmbase16" />
<ecu id= "2E12495306" name= "MY04 Impreza 2.5 STI (US)" type= "AJ243" include= "ssmbase32" />
<ecu id= "2F1A355006" name= "MY05 Legacy 3.0 Auto (US)" type= "AH63B-7273" include= "ssmbase" />
<ecu id= "2F12505106" name= "MY05 Legacy 2.5 GT (US)" type= "AJ18A-6824" include= "ssmbase32" />
<ecu id= "2F12795106" name= "MY05 Legacy 2.5 Outback XT (US)" type= "AJ65A-7904" include= "ssmbase32" />
<ecu id= "2904445205" name= "MY01 Impreza 2.0 WRX (JDM)" type= "AH000-3573" include= "ssmbase16" />
<ecu id= "3E14484006" name= "MY05 Impreza 2.0 WRX (US)" type= "AJ890-8851" include= "ssmbase16" />
<ecu id= "2F12785106" name= "MY05 Legacy 2.5 GT (US)" type= "AJ17A-6814" include= "ssmbase32" />
<ecu id= "3152584006" name= "MY04 Forester 2.5 XT (AUS)" type= "AJ530-7671" include= "ssmbase32" />
<ecu id= "3D04594005" name= "MY05 Impreza 2.0 STI (JDM)" type= "AJ810-8801" include= "ssmbase16" />
<ecu id= "3D044A4005" name= "MY05 Impreza 2.0 STI Spec C (JDM)" type= "AJ820-8810" include= "ssmbase16" />
<ecu id= "3712405006" name= "Baja 2.5 Turbo (US)" type= "AJ460-7371" include= "ssmbase32" />
<ecu id= "3E14444006" name= "MY05 Impreza 2.0 WRX (US)" type= "AJ900-8861" include= "ssmbase16" />
<ecu id= "2E14446206" name= "MY04 Impreza 2.0 WRX Auto (US)" type= "AH803" include= "ssmbase16" />
<ecu id= "2904497105" name= "MY03 Impreza 2.0 STI (JDM)" type= "AH191" include= "ssmbase16" />
<ecu id= "3D44593005" name= "MY05 Impreza 2.0 STI Type UK (EURO)" type= "AJ840-8830" include= "ssmbase16" />
<ecu id= "3614486405" name= "MY03 Impreza 2.0 WRX (US)" type= "AJ053" include= "ssmbase16" />
<ecu id= "3A54504005" name= "MY04 Impreza 2.0 WRX Auto (AUS)" type= "AJ410-7540" include= "ssmbase16" />
<ecu id= "3C54784106" name= "MY04 Legacy 2.0 GT (AUS)" type= "AK311-0271" include= "ssmbase16" />
<ecu id= "1B14400805" name= "MY01/02 Impreza 2.0 WRX (US)" type= "AF426" include= "ssmbase16" />
<ecu id= "2F54505206" name= "MY04 Legacy 2.0 GT (AUS)" type= "AH132-5895" include= "ssmbase16" />
<ecu id= "3B42584006" name= "MY04 Forester 2.5 XT (EURO)" type= "AJ590-8481" include= "ssmbase32" />
<ecu id= "3712485006" name= "Baja 2.5 Turbo (US)" type= "AJ450" include= "ssmbase32" />
<ecu id= "2EA4584005" name= "MY04 Impreza 2.0 WRX (US)" type= "AH760-5150" include= "ssmbase16" />
<ecu id= "3D54593005" name= "MY04 Impreza 2.0 STI (AUS)" type= "AJ870-8840" include= "ssmbase16" />
<ecu id= "1804440205" name= "MY99 Legacy 2.0 Auto (JDM)" type= "AG292" include= "ssmbase" />
<ecu id= "3D54583005" name= "MY05 Impreza 2.0 WRX (AUS)" type= "AJ850-8930" include= "ssmbase" />
<ecu id= "3B02594006" name= "MY04 Forester 2.5 XT (JDM)" type= "AJ540-8431" include= "ssmbase32" />
<ecu id= "3D44583005" name= "MY05 Impreza 2.0 WRX (EURO)" type= "AJ830-8820" include= "ssmbase16" />
<ecu id= "2F04785306" name= "MY04 Legacy 2.0 GTB (JDM)" type= "AH112" include= "ssmbase16" />
<ecu id= "2904444005" name= "MY03 Impreza 2.0 WRX (JDM)" type= "AH730-0730" include= "ssmbase16" />
<ecu id= "3E14483006" name= "MY05 Impreza 2.0 WRX (US)" type= "AJ890-861" include= "ssmbase16" />
<ecu id= "3B52583006" name= "MY04 Forester 2.5 XT (AUS)" type= "AK030-8900" include= "ssmbase32" />
<ecu id= "2D54544005" name= "MY03 Legacy 2.0 B4 Twin-Turbo (AUS)" type= "AH650-4430" include= "ssmbase16" />
<ecu id= "3C5A384106" name= "Legacy 3.0 B4 H6 (AUS)" type= "AK170-0471" include= "ssmbase" />
<ecu id= "0D42100705" name= "MY01 Legacy 2.5 RX (EURO)" type= "AG980-1516" include= "ssmbase" />
<ecu id= "2E46104005" name= "MY03 Impreza 1.6 (EURO)" type= "AH300-3525" include= "ssmbase" />
<ecu id= "1B46100905" name= "MY02 Impreza 1.6 (EURO)" type= "AF494" include= "ssmbase" />
<ecu id= "2D045B6005" name= "MY03 Legacy 2.0 B4 Twin-Turbo S401 (JDM)" type= "S401-7160" include= "ssmbase16" />
<ecu id= "2604686605" name= "Legacy 2.0 B4 Twin-Turbo (JDM)" type= "" include= "ssmbase16" />
<ecu id= "3C04504106" name= "MY04 Legacy 2.0 GT Auto (JDM)" type= "AK231-0262" include= "ssmbase16" />
<ecu id= "3C04784106" name= "MY04 Legacy 2.0 GT (JDM)" type= "AK221-0251" include= "ssmbase16" />
<ecu id= "3C54504106" name= "MY04 Legacy 2.0 GT (AUS)" type= "AK321-0281" include= "ssmbase16" />
<ecu id= "3F12484006" name= "MY05 Baja 2.5 Turbo (US)" type= "AJ960-8960" include= "ssmbase32" />
<ecu id= "2F12505206" name= "MY05 Legacy 2.5 GT (US)" type= "AJ18B-6825" include= "ssmbase32" />
<ecu id= "2F12785206" name= "MY05 Legacy 2.5 GT (US)" type= "AJ17B-6815" include= "ssmbase32" />
<ecu id= "2F04785406" name= "MY04 Legacy 2.0 GTB (JDM)" type= "AH113-5647" include= "ssmbase16" />
<ecu id= "2F12515106" name= "MY05 Legacy 2.5 Outback XT (US)" type= "AJ66A-7914" include= "ssmbase32" />
<ecu id= "2E04404005" name= "MY05 Impreza 2.0 WRX (JDM)" type= "AH740-5110" include= "ssmbase16" />
<ecu id= "3C4A384106" name= "Legacy 3.0 R Spec B (EURO)" type= "AK150-0442" include= "ssmbase" />
<ecu id= "3B44503006" name= "MY05 Forester 2.0 (EURO)" type= "AK010-8880" include= "ssmbase16" />
<ecu id= "3C04504216" name= "MY04 Legacy 2.0 GT Auto (JDM)" type= "AK232-0263" include= "ssmbase16" />
<ecu id= "3B52503006" name= "MY04 Forester 2.5 XT (AUS)" type= "AK040-8900" include= "ssmbase32" />
<ecu id= "3C54784216" name= "MY04 Legacy 2.0 GT (AUS)" type= "AK312-0272" include= "ssmbase16" />
<ecu id= "3B12584006" name= "MY05 Forester 2.5 XT (US)" type= "AJ570-8462" include= "ssmbase32" />
<ecu id= "3D12594106" name= "MY05 Impreza 2.5 STI (US)" type= "AJ931-8792" include= "ssmbase32" />
<ecu id= "3F12484106" name= "MY05 Baja 2.5 Turbo (US)" type= "AJ960-896" include= "ssmbase32" />
<ecu id= "3C54504216" name= "MY04 Legacy 2.0 GT Auto (AUS)" type= "AK322-0282" include= "ssmbase16" />
<ecu id= "3D045B4005" name= "Impreza 2.0 S203 (JDM)" type= "S203" include= "ssmbase16" />
<ecu id= "3B12504006" name= "MY05 Forester 2.5 XT (US)" type= "AJ580" include= "ssmbase32" />
<ecu id= "3B52583116" name= "MY05 Forester 2.5 XT (AUS)" type= "AK031-8901" include= "ssmbase32" />
<ecu id= "3B44503116" name= "MY05 Forester 2.0 (EURO)" type= "AK011-8881" include= "ssmbase16" />
<ecu id= "2604446605" name= "Legacy 2.0 B4 Twin-Turbo (JDM)" type= "AG454-0998" include= "ssmbase16" />
<ecu id= "3B12504106" name= "Forester 2.5 Auto (US)" type= "" include= "ssmbase32" />
<ecu id= "18441008FF" name= "MY03 Legacy 2.0 GX (EURO)" type= "" include= "ssmbase" />
<ecu id= "23545004FF" name= "MY02 Forester 2.0 (AUS)" type= "AG540-0243" include= "ssmbase" />
<ecu id= "" name= "MY03 Impreza WRX 2.0 (JDM)" type= "AJ051" include= "ssmbase16" />
<ecu id= "2E044A60FF" name= "MY03 Impreza 2.0 STI Spec C (JDM)" type= "AH591-5132" include= "ssmbase16" />
<ecu id= "4242584106" name= "MY06 Forester 2.5 XT (EURO)" type= "AK710-1520" include= "ssmbase32" />
<ecu id= "3C54784316" name= "MY05 Legacy 2.0 GT (AUS)" type= "AK313-0273" include= "ssmbase16" />
<ecu id= "2F12785306" name= "MY05 Legacy 2.5 GT (US)" type= "AJ17C-6816" include= "ssmbase32" />
<ecu id= "3B42584116" name= "MY05 Forester 2.5 XT (EURO)" type= "AJ591-8482" include= "ssmbase32" />
<ecu id= "2F12515206" name= "MY05 Legacy Outback 2.5 XT (US)" type= "AJ66B-7915" include= "ssmbase32" />
<ecu id= "2F04505306" name= "MY04 Legacy 2.0 GT (JDM)" type= "AH123-5887" include= "ssmbase16" />
<ecu id= "4344304006" name= "MY06 Impreza 2.0 (EURO)" type= "AL240-5607" include= "ssmbase" />
<ecu id= "43045A4005" name= "MY06 Impreza 2.0 (JDM)" type= "AL380-2270" include= "ssmbase" />
<ecu id= "3B12584106" name= "MY05 Forester 2.5 (US)" type= "AJ571-8463" include= "ssmbase32" />
<ecu id= "4312594006" name= "MY06 Impreza 2.5 (US)" type= "AL370-2221" include= "ssmbase32" />
<ecu id= "4312584006" name= "MY06 Impreza 2.5 (US)" type= "AL350-2201" include= "ssmbase32" />
<ecu id= "2F12505306" name= "MY05 Legacy 2.5 GT (US)" type= "AJ18C-6826" include= "ssmbase32" />
<ecu id= "4212585106" name= "MY05 Forester 2.5 (US)" type= "AK752-1564" include= "ssmbase32" />
<ecu id= "1B04490305" name= "MY01/02 Impreza 2.0 STI (JDM)" type= "AF480-7540" include= "ssmbase16" />
<ecu id= "401A344206" name= "Tribeca 3.0 (US)" type= "AK12A-0343" include= "ssmbase" />
<ecu id= "454A384006" name= "Legacy 3.0 (EURO)" type= "AL010-1680" include= "ssmbase" />
<ecu id= "2F0A367216" name= "Legacy 3.0 (JDM)" type= "AH612-7255" include= "ssmbase" />
<ecu id= "2F0A367106" name= "Legacy 3.0 (JDM)" type= "AH611-7254" include= "ssmbase" />
<ecu id= "3B12504206" name= "Forester 2.5 Auto (US)" type= "AJ582-8474" include= "ssmbase" />
<ecu id= "2F12784006" name= "MY05 Legacy 2.5 GT (US)" type= "AJ17A-6812" include= "ssmbase32" />
<ecu id= "4212505106" name= "MY05 Forester 2.5 Auto (US)" type= "AK762-1574" include= "ssmbase32" />
<ecu id= "4252504106" name= "MY06 Forester 2.5 (AUS)" type= "AL120-1610" include= "ssmbase32" />
<ecu id= "2604686405" name= "Legacy 2.0 B4 Twin-Turbo (JDM)" type= "AG442-0986" include= "ssmbase16" />
<ecu id= "4352584006" name= "MY06 Impreza 2.5 WRX (AUS)" type= "AL330-2180" include= "ssmbase32" />
<ecu id= "4252584106" name= "MY06 Forester 2.5 (AUS)" type= "AL110-1600" include= "ssmbase32" />
<ecu id= "4512783106" name= "MY06 Legacy 2.5 GT (US)" type= "AK45B-0991" include= "ssmbase32" />
<ecu id= "3112485206" name= "MY03 Forester 2.5 XT (US)" type= "AJ471-7313" include= "ssmbase32" />
<ecu id= "3D545B6005" name= "MY05 Impreza 2.0 WRX WRP10 (AUS)" type= "WRP10" include= "ssmbase16" />
<ecu id= "4352594006" name= "MY06 Impreza 2.5 STI (AUS)" type= "AL390-2230" include= "ssmbase32" />
<ecu id= "2F04505206" name= "MY04 Legacy 2.0 GT (JDM)" type= "AH122-5886" include= "ssmbase16" />
<ecu id= "4304594005" name= "MY06 Impreza 2.0 STI (JDM)" type= "AL300-2261" include= "ssmbase16" />
<ecu id= "3B02594216" name= "MY06 Forester 2.5 XT (JDM)" type= "AJ542-8433" include= "ssmbase32" />
<ecu id= "4342594006" name= "MY06 Impreza 2.5 STI (EURO)" type= "AL340-2190" include= "ssmbase32" />
<ecu id= "4342584006" name= "MY06 Impreza 2.5 WRX (EURO)" type= "AL310-2161" include= "ssmbase32" />
<ecu id= "4242504106" name= "MY06 Forester 2.5 XT Auto (EURO)" type= "AK720-1531" include= "ssmbase32" />
<ecu id= "3C04504316" name= "MY04 Legacy 2.0 GT Auto (JDM)" type= "AK233-0264" include= "ssmbase16" />
<ecu id= "2F54505306" name= "MY04 Legacy 2.0 GT (AUS)" type= "AH133-5896" include= "ssmbase16" />
<ecu id= "3C54504206" name= "MY04 Legacy 2.0 GT (AUS)" type= "AK321-0281" include= "ssmbase16" />
<ecu id= "2F12785506" name= "MY05 Legacy 2.5 GT (US)" type= "AJ17D-6817" include= "ssmbase32" />
<ecu id= "4512793106" name= "MY06 Legacy Outback 2.5 (US)" type= "AK478-1011" include= "ssmbase32" />
<ecu id= "0D04680B05" name= "MY99 Legacy 2.0 B4 Twin-Turbo (JDM)" type= "AD985" include= "ssmbase16" />
<ecu id= "3C04504006" name= "MY04 Legacy 2.0 GT Auto (JDM)" type= "AK230-0261" include= "ssmbase16" />
<ecu id= "2D4A354005" name= "MY03 Legacy 3.0 (EURO)" type= "AH080-3941" include= "ssmbase" />
<ecu id= "3B12584206" name= "MY05 Forester 2.5 (US)" type= "AJ572-8464" include= "ssmbase32" />
</logprotocol>
</logprotocols>
</ecus>