From 3bf92a25239eba68b3e1ca7273ecc85ca09715eb Mon Sep 17 00:00:00 2001
From: Dominic Clifton <me@dominicclifton.name>
Date: Fri, 23 May 2014 13:05:44 +0100
Subject: [PATCH] Updating Olimexino board documentation to cover new HoTT
 telemetry port.

---
 targets/Olimexino/notes.txt | 47 +++++++++++++++++++++++++++++++------
 1 file changed, 40 insertions(+), 7 deletions(-)

diff --git a/targets/Olimexino/notes.txt b/targets/Olimexino/notes.txt
index 7dcc9eba0..248fab10e 100644
--- a/targets/Olimexino/notes.txt
+++ b/targets/Olimexino/notes.txt
@@ -22,11 +22,13 @@ PB8  CH5 - PWM13 - D14
 PB9  CH6 - PWM14 - D24
 
 
-Olimexino Shield V1
+Olimexino Shield V1 connections
+
+Headers for a CP2102 for UART1
 
 Top left
 
-UART2 - Headers for CP2102
+6 way header pinouts (left to right)
 
 1 - N/C
 2 - N/C
@@ -35,10 +37,18 @@ UART2 - Headers for CP2102
 5 - D8 - UART1 RX / CP2102 TX
 6 - GND
 
+Headers for PPM, RSSI, SoftSerial1 inputs and Motor outputs
+
 Top centre
 
-1 - D2  - PWM1
-2 - D3  - PWM2
+Top Row = GROUND
+Middle Row = 5V
+Bottom Row = Signals
+
+Signal pinouts (left to right)
+
+1 - D2  - PWM1 - PPM
+2 - D3  - PWM2 - RSSI
 3 - D11 - PWM6  - INPUT CH6 / SS1 TX
 4 - D12 - PWM5  - INPUT CH5 / SS1 RX
 5 - D5  - PWM11 - OUTPUT CH3
@@ -46,9 +56,12 @@ Top centre
 7 - D14 - PWM13 - OUTPUT CH5
 8 - D24 - PWM14 - OUTPUT CH6
 
+
+SoftSerial 1 - Headers for FTDI
+
 Top Right
 
-SoftSeral 1 - Headers for FTDI
+6 way header pinouts (left to right)
 
 1 - N/C
 2 - D11 - SS1 or UART2 TX / FTDI RX
@@ -57,9 +70,11 @@ SoftSeral 1 - Headers for FTDI
 5 - N/C
 6 - GND
 
+Serial IO & Serial Loopback  
+
 Bottom right
 
-6 way header allowing combinations of serial loopback and serial i/o
+The header pins allows combinations of serial loopback and Serial IO.  Any amount of connections or jumpers can be used at the same time.
 
 Jumper positions
 
@@ -83,7 +98,7 @@ v-- SS1 LOOPBACK
 --v UART2 LOOPBACK
 --^  
 
-Pinouts
+6 way header pinouts (top left to bottom right)
 
 123
 456
@@ -94,3 +109,21 @@ Pinouts
 4 - SS1 RX
 5 - FTDI TX
 6 - UART2 RX
+
+Bottom Right
+
+HoTT Telemetry port
+
+When the HoTT enable jumper is on pins 2 and 3 then HoTT data can be received/transmitted on either
+serial port depending on the placement of the Derial IO selection jumpers.
+
+When not in use the HoTT enable jumper can be stored on pins 3 and 4
+
+The HoTT telemetry is connected to the center pins (2 & 5) of the Serial IO header.
+
+4 way header (left to right)
+
+1 - HoTT Telemetry In/Out
+2 - HoTT Enable Jumper
+3 - HoTT Enable Jumper
+4 - N/C - Jumper Storage