parent
353b071441
commit
94d3ce8046
|
@ -360,14 +360,7 @@ custom pin_output_mode_e 1 bits, U08, @OFFSET@, [0:1], @@pin_output_mode_e_enum@
|
|||
#define pin_input_mode_e_enum "DEFAULT", "PULLUP", "PULLDOWN"
|
||||
custom pin_input_mode_e 1 bits, U08, @OFFSET@, [0:1], @@pin_input_mode_e_enum@@
|
||||
|
||||
struct spi_pins
|
||||
Gpio mosiPin;
|
||||
Gpio misoPin;
|
||||
Gpio sckPin;
|
||||
end_struct
|
||||
|
||||
|
||||
#define gppwm_channel_e_enum "Zero", "TPS", "MAP", "CLT", "IAT", "Fuel Load", "Ignition Load", "Aux Temp 1", "Aux Temp 2", "Accel Pedal", "Battery Voltage", "VVT 1 I", "VVT 1 E", "VVT 2 I", "VVT 2 E", "Ethanol (Flex) %", "Aux Linear 1", "Aux Linear 2", "GPPWM Output 1", "GPPWM Output 2", "GPPWM Output 3", "GPPWM Output 4", "Lua Gauge 1", "Lua Gauge 2", "RPM"
|
||||
#define gppwm_channel_e_enum "Zero", "TPS", "MAP", "CLT", "IAT", "Fuel Load", "Ignition Load", "Aux Temp 1", "Aux Temp 2", "Accel Pedal", "Battery Voltage", "VVT 1 I", "VVT 1 E", "VVT 2 I", "VVT 2 E", "Ethanol (Flex) %", "Aux Linear 1", "Aux Linear 2", "GPPWM Output 1", "GPPWM Output 2", "GPPWM Output 3", "GPPWM Output 4", "Lua Gauge 1", "Lua Gauge 2", "RPM", "Gear (detected)"
|
||||
custom gppwm_channel_e 1 bits, U08, @OFFSET@, [0:4], @@gppwm_channel_e_enum@@
|
||||
|
||||
struct gppwm_channel
|
||||
|
@ -632,8 +625,8 @@ struct afr_sensor_s
|
|||
float value1;;"AFR", 1, 0, 0, 1000, 2
|
||||
float v2;;"volts", 1, 0, 0, 10, 2
|
||||
float value2;;"AFR", 1, 0, 0, 1000, 2
|
||||
end_struct
|
||||
|
||||
end_struct
|
||||
|
||||
afr_sensor_s afr
|
||||
|
||||
adc_channel_e throttlePedalPositionAdcChannel;Electronic throttle pedal position first channel\nSee throttlePedalPositionSecondAdcChannel for second channel\nSee also tps1_1AdcChannel\nset_analog_input_pin pps X\nSee throttlePedalUpVoltage and throttlePedalWOTVoltage
|
||||
|
@ -716,7 +709,7 @@ switch_input_pin_e clutchDownPin;Some cars have a switch to indicate that clutch
|
|||
Gpio cj125CsPin;set_cj125_cs_pin XXX
|
||||
spi_device_e max31855spiDevice;
|
||||
Gpio debugTriggerSync;
|
||||
|
||||
|
||||
spi_device_e digitalPotentiometerSpiDevice;Digital Potentiometer is used by stock ECU stimulation code
|
||||
Gpio mc33972_cs;
|
||||
pin_output_mode_e mc33972_csPinMode;
|
||||
|
@ -779,7 +772,7 @@ bit is_enabled_spi_2
|
|||
bit isHip9011Enabled
|
||||
bit isVerboseAlternator
|
||||
bit verboseQuad
|
||||
bit useStepperIdle;This setting should only be used if you have a stepper motor idle valve and a stepper motor driver installed.
|
||||
bit useStepperIdle;This setting should only be used if you have a stepper motor idle valve and a stepper motor driver installed.
|
||||
|
||||
bit enabledStep1Limiter
|
||||
bit useTpicAdvancedMode
|
||||
|
@ -879,7 +872,6 @@ custom uart_device_e 1 bits, U08, @OFFSET@, [0:1], "Off", "UART1", "UART2", "UAR
|
|||
custom script_setting_t 4 scalar, F32, @OFFSET@, "", 1, 0, 0, 18000, 2
|
||||
script_setting_t[SCRIPT_SETTING_COUNT iterate] scriptSetting;
|
||||
|
||||
! todo: migrate to spi_pins & combine with spi pin modes
|
||||
Gpio spi1mosiPin;
|
||||
Gpio spi1misoPin;
|
||||
Gpio spi1sckPin;
|
||||
|
|
Loading…
Reference in New Issue