* smart gpio: fix tle8888 direct pin mapping for MRE
* MRE: use TLE8888 pins instead of MCU gpios that drives TLE8888
* TLE8888: cleanup
* TLE8888: do not reset driver private data on WD/undervoltage reset
* TLE8888: diagnostic updates
* TLE8888 driver: BIG driver rework
* TLE8888: check SPI answers for abnormal states
Reply with other than requested register can be a sign of:
-Power-On-Reset, then OpStat0 will be replyed
-WatchDog reset, then FWDStat1 will be replyed
-Invalid communication frame, then Diag0 will be replyed
Keep tracking last accessed register and check with the next reply.
* TLE8888: debug clean-up
* TLE8888: implement spi array write
This reduce CS inactive state time between two consequent accesses
from 8.8 uS to 1.4 uS
* TLE8888: fix PP outputs in OD mode
* TLE8888: cleanup register definitions
* TLE8888: run separate driver thread for each chip instance
Calculating poll interval for few chips become more complex, avoid
this running thread for each device.
* TLE8888: fix cypress and kinetic compilation
Both platforms define its own MAX and cause redifination error if
common.h is included in driver.
* MRE: update mapping.yaml and fix direct pin mapping for TLE8888
* TLE8888: diagnnostic: disable switch off in case of overcurrent
For all output, use current limiting instead
* TLE8888: check for overvoltage on OUT8..OUT13
* TLE8888: add TODO note about how to recover from failure condition
Currently TLE8888 automaticly recovers only from overcurrent and
(may be) overtemperature conditions.
Short to bat cause output disable (bit in OECONFIG is reset) and
needs driver/host intervention.
* TLE8888: save few bytes of RAM
* TLE8888: Lada Kalina is test mule for IDLE stepper on TLE8888
Don't forget to enable PP mode for TLE8888 outputs 21..24:
uncomment line 1087 in tle8888.c
* TLE8888: reorder code, cleanup
* TLE8888: mode all debug/statisctic to per-chip struct
* TLE8888: rework poll interval calculation
* MRE: use TLE8888 pins instead of MCU gpios that drives TLE8888 #2
* Add SW knock control to MRE on AT4
* Update software_knock.cpp
cleanup
* use knock only for final build
* adjust RAM
* Update engine_controller.cpp
Adjust RAM for HW QC special to build
* s
* science
* set pin mode
* turn stuff off so it fits
* filtering maybe
* filtering actually works
* generate filter parameters internally
* shorter window
* guard behind enable flag
* use checked in filter
* add biquad reset
* tracing
* const
* exec order
* do it from a thread
* smaller buffer, comment
* configure with header
* only for proteus
* oops
* unused
* not needed
* guards
* pin config
* don't need that include
* precook filter steady state
* define sample rate
* config enable switch
* add env var to skip upload
* remove checking from compile.bat
* working on push.yaml
* finish sorting
* progress
* rename push to builds
* rename push to builds
* Add skip upload env var
* fix pull_request name
* fixed typo and changed name
* fixed indentation and runs-on
* try different env var setup
* add nucleos and switch to underscore
* add quotes
* remove boards that were commented
* remove boards that were commented
* fix project board name
* fixed variable name
* add ini-file and console-settings
* try installing gcc-multilib first
* Install g++-multilib as well
* remove unnecessary export
* fixed exit numbers
* change to different env setup
* add simulator and console compilation to board bundles
* changed OS and added linux simulator build
* add checkout and missing colon
* add gcc-multilib installes
* Install mingw
* fixed install
* remove mingw from linux sim and call compile directly
* change directory
* moved envs to command
* debug ls
* debug ls
* set ftp vars
* add makefile debug info
* removed batchecks
* redirect stdout to easier see orrs
* change name
* remove redirect, add file inpection
* Add conditional project name
* Try software upgrade
* missing char
* update ine files
* try quotes
* add escapes
* add quotes
* add escapes and quotes
* remove quotes and escapes
* remove software upgrade
* ignore test 2
* update apt
* like this then
* forgot import
* fix case
* remove RUSEFI_SKIP_UPLOAD and check RUSEFI_FTP_SERVER instead
* break workflow back apart
* upload simulator artifact
* fixed operator
* update apt
* change paths
* Update build-firmware.yaml
* move update bundle to artifacts
* fix var name
* Install ncftp
* set env vars conditionally
* remove check so zips are created
* try things the github way and copy to primary
* re-enable test
* missing space
rusefi
Matthew Kennedy
Andrey G
rusefillc
David Holdeman
andreika-git
shadowm60
Andrei
kon