* 429 boots and LEDs work
* oops missed a comma
* enable on f767 too, since it should be the same board
* why not just completely duplicate it
* script should not be fancy
* script should not be fancy
* correct pins
* h743 while we're at it
* tle8888: ups IGN1
* tle8888: more BIT() macro
* tle8888: fix typos
* tle8888: fix LS2 output on MRE when stepper is enabled
Default settings casue one (or few) not used direct driver inputs
to be mapped to OUT5 (LS2 on MRE)
* smart_gpio: comments for TLE8888 on MicroRusEFI
* smart_gpio: typo
* tle8888: more comments
* make things c++ friendly
* install various canaries in coal mines
* using is much clearer than typedef
* fixing builds
* lps25
* trigger includes were a mess
* c -> c++ cleanup
* os util
* why did so many include os_util.h?
* fwd declare
* cypress/kinetis
* s
* eg33 happy
* happy sim
* cypress usb
* pch
* cypress
* doesn't need to include all that
* h7
* Typo fix
* flash_main: always allow to write settings to ext NOR while running
* mc33810: do not enable outputs right after undervoltage
Wait for next active signal
* QSPI flash: set correct dummy cycles for fast read command
* board subaru: fix connector pinout. again.
* board subaru: fix SDMMC pin configuration
* board subaru: fix DMA conflict SPI4_RX vs SDMMC2
* big pch energy
* put back ramdisk stub
* tests are happy
* h743 nucleo
* kinetis
* I love deleting code!
* make stepper happy
Co-authored-by: Matthew Kennedy <makenne@microsoft.com>
* tle6240: fix Matt's trap
* map: report some default value if no map sensor configured
Othervise user will get "unexpected MAP value" warning
Thread 2 hit Breakpoint 1, validateMap (mapKPa=3121.66162) at ./controllers/sensors/map.cpp:126
126 if (cisnan(mapKPa) || mapKPa < CONFIG(mapErrorDetectionTooLow) || mapKPa > CONFIG(mapErrorDetectionTooHigh)) {
(gdb) bt
0 validateMap (mapKPa=3121.66162) at ./controllers/sensors/map.cpp:126
1 0x002717dc in getMap () at ./controllers/engine_cycle/map_averaging.cpp:334
2 0x0028175a in GetMapWrapper::getMap (this=0x2004214c <mapWrapper>) at ./init/sensor/init_map.cpp:12
3 0x0028177c in operator() (__closure=0x0) at ./init/sensor/init_map.cpp:20
4 0x002817a8 in _FUN () at ./init/sensor/init_map.cpp:21
5 0x002811de in FunctionPointerSensor::get (this=0x20042150 <mapSensor>) at ./controllers/sensors/function_pointer_sensor.h:24
6 0x002651c0 in SensorRegistryEntry::get (this=0x2003ddf0 <s_sensorRegistry+48>) at ./controllers/sensors/sensor.cpp:111
7 0x002653e2 in Sensor::get (type=SensorType::Map) at ./controllers/sensors/sensor.cpp:208
8 0x00261f38 in updateTunerStudioState (tsOutputChannels=0x2003d2e8 <tsOutputChannels>) at ./console/status_loop.cpp:637
9 0x00262e48 in prepareTunerStudioOutputs () at ./console/status_loop.cpp:900
10 0x00260914 in TunerStudio::cmdOutputChannels (this=0x20021a64 <tsInstance>, tsChannel=0x2003d4dc <usbChannel>, offset=0, count=340) at ./console/binary/tunerstudio_commands.cpp:24
11 0x00260584 in TunerStudioBase::handleCrcCommand (this=0x20021a64 <tsInstance>, tsChannel=0x2003d4dc <usbChannel>, data=0x2003d4e1 <usbChannel+5> "", incomingPacketSize=5)
at ./console/binary/tunerstudio.cpp:701
12 0x0025fb3c in tsProcessOne (tsChannel=0x2003d4dc <usbChannel>) at ./console/binary/tunerstudio.cpp:537
13 0x0025fbe2 in TunerstudioThread::ThreadTask (this=0x2003d608 <usbConsole>) at ./console/binary/tunerstudio.cpp:554
14 0x0025f094 in ThreadController<1200>::StaticThreadTaskAdapter (thread=0x2003d608 <usbConsole>) at ./controllers/system/thread_controller.h:37
15 0x0020035e in _port_thread_start () at ChibiOS/os/common/ports/ARMCMx/compilers/GCC/chcoreasm_v7m.S:201
* rename
* core
* structing
* more
* makefile
* structing
* 6240 compiles
* explicit cast instead of implicit narrowing
* 8888
* no extern C
* fix tests build
* extern "C"
* 33810
* 8860
* 33810
* linker
* unbreak master
* don't need that if compiling as C++
* bump config
* fix test
* tests
* unit tests bad merge
* build
* move subaru logic to cpp file
* cpp goodness
* hpp include
* this is probably the right thing to do
* simulator
* MC33972: update
-per-instance thread
-enable pull-ups for enabled pins only
* smart-gpio: mc33972: uses 8-bit spi frames
3 bytes are sent to make 24-bit frame
* configure for no cache
* this doesn't need a setting
* now we don't need invalidate
* reorder and comment
* mmc
* sw knock
* use spiPolledExchange for small transfers
* mock spi
Co-authored-by: Matthew Kennedy <makenne@microsoft.com>
* ChibiOS: add support for STM32F765
This chip is used on Subaru EG33 p'n'p RusEFI board from Dron_Gus
* drivers: gpio: mc33810: commulative update
- use BIT macro
- fix wake-up method
- fix order of arguments in _add function
* port: stm32f4/7: detectCanDevice check for enabled interfaces only
* ADC: fix internal array size
internalAdcIndexByHardwareIndex should be EFI_ADC_LAST_CHANNEL size
couse adc_channel_e is used as index
* status LEDs: support status LEDs that driven by low level
* We still need consoleEventListener for boards with EFI_CONSOLE_SERIAL_DEVICE
* MC33810: add MC_ prefix for command defines
As CMD_PWM define is now used by console command
* switch to CriticalSectionLocker
* that's just about all
* clean up last usage
* include hpp for sim
* need the cpp wrappers in the makefile too
* include dir
* include
rusefi
rusefillc
Matthew Kennedy
Andrey G
Scott Smith