81 lines
1.8 KiB
Plaintext
81 lines
1.8 KiB
Plaintext
*** Hellen One: Hellen72 Frame specs (DRAFT) ***
|
|
|
|
General info: https://rusefi.com/s/hellen72/
|
|
|
|
EDA Software: Altium Designer
|
|
|
|
Board/connector footprints source: <.../hw_72_nb>
|
|
|
|
Pinout spreadsheet: <...>
|
|
|
|
Modules:
|
|
- mcu/0.1
|
|
- input/0.1
|
|
- output/0.1
|
|
- power5/0.1
|
|
- power12/0.1
|
|
- can/0.1
|
|
- lin/0.1
|
|
- ign8/0.1
|
|
- sd/0.1
|
|
- stlink/0.1
|
|
- knock/0.1
|
|
|
|
- Additional components:
|
|
- USB-B vertical TH: TE 5787834-1
|
|
- "PROG" button
|
|
- "RESET" button
|
|
- Accelerometer
|
|
- MAP sensor: MPX4250AP
|
|
- SD-Card module connector: <SD-CARD module info>
|
|
- "Extension port" connector:
|
|
- UART
|
|
- SPI
|
|
- IO1-IO4
|
|
- +3.3V, +5V, +12V, GND
|
|
|
|
- Board configuration:
|
|
- Jumper resistors for pins:
|
|
- 3L = IN_AFR or OUT_IGN7
|
|
- 3Z = GNDA or OUT_IGN5
|
|
- 4K = V5A or OUT_IGN6
|
|
- 4U = IN_MAP2 or OUT_IGN8
|
|
- IN_VIGN = 4S or 4T
|
|
- Standard input pullups (V5A):
|
|
- RES1, RES2
|
|
- AUX1, AUX2, AUX3, AUX4
|
|
- TPS, PPS, O2S, O2S2, IAT, CLT
|
|
- CRANK, CAM, VSS
|
|
- SENS3 (FUEL_LEVEL)
|
|
- Standard input pulldowns (GNDA):
|
|
- MAP1, MAP2, MAP3, MAP4
|
|
- KNOCK
|
|
- SENS1, SENS2, SENS4
|
|
- Additional pulldowns (GNDA):
|
|
- IN_MAF (1k)
|
|
|
|
- Additional LEDS:
|
|
- IGN1-IGN8 (to GND)
|
|
- INJ1-INJ8 (to +12V, protected)
|
|
- AC, PUMP, IDLE, ECF, VVT, O2H, O2H2, CE, ALT_WARN, MAIN, CANIST (to +12V, protected)
|
|
- TACH, ALTERN, VIGN (to GND, protected)
|
|
- CRANK, CAM, VSS (to +5V, protected)
|
|
- +5V, +3.3V
|
|
- Jumper resistors for LEDS: VSS, CAM, CRANK
|
|
|
|
- Additional TEST PADS:
|
|
- +12V
|
|
- +5V
|
|
- +3.3V
|
|
- GND
|
|
|
|
- Silkscreen:
|
|
- silkscreen/board orientation - the ECU connector is at the top
|
|
- all pins named (both sides)
|
|
- https://rusefi.com/s/hellen72/
|
|
- "for notes" area 50x20 mm
|
|
|
|
- Special layout requirements:
|
|
- SD-Card should be 10-20 mm away from other components
|
|
- MPX4250 hose output opposite to the ECU connector
|