;------------------------------------------------------------------------------- ; $Id: core.ini,v 1.269.2.35 2014/11/09 12:15:00 jsmcortina Exp $ ; ; This ini file is Copyright 2007,2008,2009,2010,2011,2012,2013 James Murray and Kenneth Culver. ; It is only to be used with a genuine B&G MS3. ; ; Original author(s) uncertain. Contains work of Eric Fahlgren ; Re-written to support MS3 ; ; ; configuration defines, either #set or #unset ;This enables the "full" CAN/serial commands so this INI can be used anywhere on the CAN network. #set CAN_COMMANDS #unset INI_VERSION_2 ; this is set by TunerStudio, but needs to be unset for Megatune to work #unset INTERNAL_LOG_FIELDS #unset PW_4X #unset CYL_12_16_SUPPORT #unset PORT_STATUS #unset OUTMSG_EDITING ; Allow editing of the outmsg data [MegaTune] MTversion = 2.25 ; MegaTune itself; needs to match exec version. #if CAN_COMMANDS versionInfo = "r\$tsCanId\x0e\x00\x00\x00\x3c" ; Title bar queryCommand = "r\$tsCanId\x0f\x00\x00\x00\x14" ; Verify against signature. #else versionInfo = "S" ; Put this in the title bar. queryCommand = "Q" ; Verify against signature. #endif signature = "MS3 Format 0435.14 " ; MS-II sends a null at 20th byte. ; 123456789.123456789. [TunerStudio] iniSpecVersion = 3.24 helpManualDownloadRoot = "http://www.msextra.com/doc/pdf/" ;---------------------------------------------------------------------------- #if INI_VERSION_2 ; ok #else #error Megatune cannot be used with MS3 - please upgrade to TunerStudio #endif ;---------------------------------------------------------------------------- ; Temperature Limits and Settings Reference ; contributed by Mike Soultanian ;---------------------------------------------------------------------------- ; ; Below is a listing of all of the temperature ranges used throughout the INI ; for the MegaSquirt. ; ; CELSIUS (Expanded/Normal): ; Low limit: -40C/-40C ; High limit: 230C/150C ; Low danger: 65C/10C ; Low warning: 93C/65C ; High warning: 162C/93C ; High danger: 176C/104C ; ; FAHRENHEIT (Expanded/Normal): ; Low Limit: -40F/-40F ; High limit: 450F/300F ; Low danger: 150F/50F ; Low warning: 200F/150F ; High warning: 325F/200F ; High danger: 350F/220F (also used for curve editor limits) ;---------------------------------------------------------------------------- [ReferenceTables] tableWriteCommand = "w\$tsCanId%2i%2o%2c%v" #if CAN_COMMANDS tableBlockingFactor = 256 ; just in case MS2 is used #else tableBlockingFactor = 2048 #endif referenceTable = mafTableBurner, "Calibrate MAF Table..." tableIdentifier = 003, "MAF Table" adcCount = 1024 ; length of the table bytesPerAdc = 2 ; using words scale = 1 ; scale before sending to controller tableGenerator = fileBrowseGenerator, "Browse for Inc File" solutionsLabel = "MAF Sensor" solution = "Default", { table(adcValue, "maffactor.inc") } solution = "Ford V8", { table(adcValue, "maffactor.inc") } solution = "Ford Lightning MAF", { table(adcValue, "maffactor_1L3F_Lightning.inc") } solution = "Infiniti Q45 MAF", { table(adcValue, "maffactor_Q45.inc") } ; solution = "GM LT1/LS1/LS2 MAF", { table(adcValue, "maffactor_lsx.inc") } ; file is not valid, use new method instead solution = "Custom inc File", fileBrowseGenerator [SettingGroups] ; the referenceName will over-ride previous, so if you are creating a ; settingGroup with a reference name of lambdaSensor, it will replace the ; setting group defined in the settingGroups.xml of the TunerStudio config ; folder. If is is an undefined referenceName, it will be added. ; keyword = referenceName, DisplayName settingGroup = lambdaSensor, "Oxygen Sensor / Display" settingOption = NARROW_BAND_EGO, "Narrowband Sensor - Volts" settingOption = LAMBDA, "Wideband - Lambda" settingOption = DEFAULT, "WideBand - AFR" ; DEFAULT will be over looked and this will fall into the #else block of the statement. settingGroup = lambdaDisplay, "" ; Hide this settingGroup option settingOption = DEFAULT, "" ; [PcVariables] ; valid types: boolean, double, int, list ; ; no offset as they are local variables. ; entry format the same as Constants, except there is no offset. ; arrays are not yet supported. ; name = class, type, shape, units, scale, translate, lo, hi, digits ; name = type, min, max; ; ; type List: value will be index. ;tsCanId = bits, U08, [0:3] ; The short one, just numbers tsCanId = bits, U08, [0:3], "CAN ID 0", "CAN ID 1", "CAN ID 2", "CAN ID 3", "CAN ID 4", "CAN ID 5", "CAN ID 6", "CAN ID 7", "CAN ID 8", "CAN ID 9", "CAN ID 10","CAN ID 11","CAN ID 12","CAN ID 13","CAN ID 14","INVALID" ; testScale = scalar, U16, "%", 0.001, 0, 0, 600, 4 ; testTransform = scalar, U08, "#", 0.1, 0, 0, 25.5, 1 rpmhigh = scalar, U16, "rpm", 1, 0, 0, 30000, 0 rpmwarn = scalar, U16, "rpm", 1, 0, 0, 30000, 0 rpmdang = scalar, U16, "rpm", 1, 0, 0, 30000, 0 loadhigh = scalar, U16, "", 1, 0, 100, 1000, 0 wue_lpg = bits, U08, [0:0], "No", "Yes" vehigh = scalar, U16, "%", 1, 0, 100, 600, 0 clt_exp = bits, U08, [0:0], "Normal", "Expanded" algorithmUnits = bits, U08, [0:3], "%", "kPa", "%Baro", "% TPS", "MAFload", "MAFload", "ITB", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" ; * sensor01Alias = string, ASCII, 20 sensor02Alias = string, ASCII, 20 sensor03Alias = string, ASCII, 20 sensor04Alias = string, ASCII, 20 sensor05Alias = string, ASCII, 20 sensor06Alias = string, ASCII, 20 sensor07Alias = string, ASCII, 20 sensor08Alias = string, ASCII, 20 sensor09Alias = string, ASCII, 20 sensor10Alias = string, ASCII, 20 sensor11Alias = string, ASCII, 20 sensor12Alias = string, ASCII, 20 sensor13Alias = string, ASCII, 20 sensor14Alias = string, ASCII, 20 sensor15Alias = string, ASCII, 20 sensor16Alias = string, ASCII, 20 scatterRuntimeEnabled = bits, U08, [0:0], "Disabled", "Enabled" portLabels = bits, U08, [0:8], "unused", "injection LED", "warmup LED", "squirt LED", "fuel pump", "PWM or on/off idle", "stepper idle", "primary injectors", "secondary injectors", "a programmable on/off output", "spark outputs", "HEI bypass", "knock", "MAF", "MAP", "baro", "EGO", "tacho out", "A/C idleup out", "A/C idleup in", "fan out", "boost out", "N2O stage 1 nitrous", "N2O stage 1 fuel", "N2O stage 2 nitrous", "N2O stage 2 fuel", "N2O in", "launch in", "variable launch in", "3 step in", "datalog button", "datalog LED", "bike shift in", "bike shift out", "generic PWM A", "generic PWM B", "generic PWM C", "generic PWM D", "generic PWM E", "generic PWM F", "datalog stream", "dual fuel in", "fuel tableswitch", "spark tableswitch", "boost tableswitch", "overboost tableswitch", "ReqFuel switch", "AFR tableswitch", "stoich switch", "max AFR safety switch", "accelerometer X", "accelerometer Y", "accelerometer Z", "vss out", "water inj pump", "water inj valve", "water inj in", "ignition trigger LED", "flex fuel in", "cam input", "vss1 in", "vss2 in", "speed sensor 1 in", "speed sensor 2 in", "gear position in", "anti-lag in", "anti-lag out", "anti-lag PWM out", "Boost 2 out", "EGT 1 in", "EGT 2 in", "EGT 3 in", "EGT 4 in", "EGT 5 in", "EGT 6 in", "EGT 7 in", "EGT 8 in", "EGT 9 in", "EGT 10 in", "EGT 11 in", "EGT 12 in", "EGT 13 in", "EGT 14 in", "EGT 15 in", "EGT 16 in", "Generic Sensor 1 in", "Generic Sensor 2 in", "Generic Sensor 3 in", "Generic Sensor 4 in", "Generic Sensor 5 in", "Generic Sensor 6 in", "Generic Sensor 7 in", "Generic Sensor 8 in", "Generic Sensor 9 in", "Generic Sensor 10 in", "Generic Sensor 11 in", "Generic Sensor 12 in", "Generic Sensor 13 in", "Generic Sensor 14 in", "Generic Sensor 15 in", "Generic Sensor 16 in", "VVT 1 output", "VVT 2 output", "VVT 3 output", "VVT 4 output", "VVT cam 2/3/4 input", "Real Time Clock", "Torque Convertor Lockup", "Traction control", "Rotary trailing dwell timer", "Internal SPI2", "2nd MAP", "Long Term Trim button", "dual-fuel injectors", "launch timed in", "launch timed out", "throttle stop", "check engine light", "vss3 in", "vss4 in", "Staged inj switch output 1", "Alternator control output", "Alternator load monitor input", "Alternator current monitor input", "Alternator lamp output", "Staged inj switch output 1", "Shift light output", "Oil pressure warning output", "TCS input", "MAP2" prefSpeedUnits = bits, U08, [0:0], "MPH", "KPH" prefLengthUnits = bits, U08, [0:0], "m", "in" [LoggerDefinition] ; valid logger types: composite, tooth, trigger, csv ;loggerDef = uniqueName, Display Name, type loggerDef = mapLogger, "MAP Logger", csv dataReadCommand = "r\\x00\\xf4\\x00\\x00\\x04\\x00" ; standard TS command format dataReadTimeout = 10000 ; time in ms dataReadyCondition = { ( status3 & 0x02 ) == 0x02 } ;dataLength = 1024 ; in bytes, including headers, footers and data (not used) ;recordDef = headerLen. footerLen, recordLen recordDef = 0, 0, 2; in bytes, the recordLen is for each record, currently limited to 4 bytes ;recordField = Name, HeaderName, startBit, bitCount, scale, units, updateCondition recordField = nonMap, "Not MAP", 15, 1, 1.0, "Flag" recordField = mapWindow, "MAPwindow", 14, 1, 1.0, "Flag", { !nonMap } recordField = rpmPrint, "isRPM", 14, 1, 1.0, "Flag", { nonMap } recordField = mapSensor, "Sensor", 10, 3, 1.0, "#", { !nonMap } recordField = mapAdc, "MAP ADC", 0, 10, 1.0, "ADC", { !nonMap } recordField = sampleRpm, "RPM", 0, 14, 1.0, "rpm", { nonMap && rpmPrint } recordField = crankAngle, "CrankAngle", 0, 13, 0.1, "deg", { nonMap && !rpmPrint } ;calcField = name, HeaderName, units, expression calcField = mapValue, "MAP", "kPa", { map0 + (mapmax - map0) * mapAdc/1023 } loggerDef = mafLogger, "MAF Logger", csv dataReadCommand = "r\\x00\\xf5\\x00\\x00\\x04\\x00" ; standard TS command format dataReadTimeout = 10000 ; time in ms dataReadyCondition = { ( status3 & 0x02 ) == 0x02 } ;dataLength = 1024 ; in bytes, including headers, footers and data (not used) ;recordDef = headerLen. footerLen, recordLen recordDef = 0, 0, 2; in bytes, the recordLen is for each record, currently limited to 4 bytes ;recordField = Name, HeaderName, startBit, bitCount, scale, units, updateCondition recordField = nonMaf, "Not MAF", 15, 1, 1.0, "Flag" recordField = mapWindow, "MAPwindow", 14, 1, 1.0, "Flag", { !nonMaf } recordField = rpmPrint, "isRPM", 14, 1, 1.0, "Flag", { nonMaf } recordField = mapSensor, "Sensor", 10, 3, 1.0, "#", { !nonMaf } recordField = mafAdc, "MAF ADC", 0, 10, 1.0, "ADC", { !nonMaf } recordField = sampleRpm, "RPM", 0, 14, 1.0, "rpm", { nonMaf && rpmPrint } recordField = crankAngle, "CrankAngle", 0, 13, 0.1, "deg", { nonMaf && !rpmPrint } calcField = mapValue, "MAF Freq", "Hz", { (MAFOption_t == 0 || (!(mafAdc > 0))) ? 0 : (maf_freq1 > 62.5) ? (1000000 / (32 * mafAdc)) : (1000000 / (128 * mafAdc)) } loggerDef = mafLogger, "Engine Logger", csv dataReadCommand = "r\\x00\\xf6\\x00\\x00\\x04\\x00" ; standard TS command format dataReadTimeout = 10000 ; time in ms dataReadyCondition = { ( status3 & 0x02 ) == 0x02 } ;dataLength = 1024 ; in bytes, including headers, footers and data (not used) ;recordDef = headerLen. footerLen, recordLen recordDef = 0, 0, 3; in bytes, the recordLen is for each record, currently limited to 4 bytes ;recordField = Name, HeaderName, startBit, bitCount, scale, units, updateCondition recordField = PT7, "PTT7", 23, 1, 1, "" recordField = PT6, "PTT6", 22, 1, 1, "" recordField = PT5, "PTT5", 21, 1, 1, "" recordField = PT4, "PTT4", 20, 1, 1, "" recordField = PT3, "PTT3", 19, 1, 1, "" recordField = PT2, "PTT2", 18, 1, 1, "" recordField = PT1, "PTT1", 17, 1, 1, "" recordField = PT0, "PTT0", 16, 1, 1, "" recordField = PB7, "Spk H", 15, 1, 1, "" recordField = PB6, "Spk G", 14, 1, 1, "" recordField = PB5, "Spk F", 13, 1, 1, "" recordField = PB4, "Spk E", 12, 1, 1, "" recordField = PB3, "Spk D", 11, 1, 1, "" recordField = PB2, "Spk C", 10, 1, 1, "" recordField = PB1, "Spk B", 9, 1, 1, "" recordField = PB0, "Spk A", 8, 1, 1, "" recordField = PA7, "Inj H", 7, 1, 1, "" recordField = PA6, "Inj G", 6, 1, 1, "" recordField = PA5, "Inj F", 5, 1, 1, "" recordField = PA4, "Inj E", 4, 1, 1, "" recordField = PA3, "Inj D", 3, 1, 1, "" recordField = PA2, "Inj C", 2, 1, 1, "" recordField = PA1, "Inj B", 1, 1, 1, "" recordField = PA0, "Inj A", 0, 1, 1, "" loggerDef = mafLogger, "Engine Logger + MAP", csv dataReadCommand = "r\\x00\\xf7\\x00\\x00\\x04\\x00" ; standard TS command format dataReadTimeout = 10000 ; time in ms dataReadyCondition = { ( status3 & 0x02 ) == 0x02 } ;dataLength = 1024 ; in bytes, including headers, footers and data (not used) ;recordDef = headerLen. footerLen, recordLen recordDef = 0, 0, 4; in bytes, the recordLen is for each record, currently limited to 4 bytes ;recordField = Name, HeaderName, startBit, bitCount, scale, units, updateCondition recordField = mapAdc, "MAP ADC", 24, 8, 4.0, "ADC" ; scaled to 8 bits recordField = PT7, "PTT7", 23, 1, 1, "" recordField = PT6, "PTT6", 22, 1, 1, "" recordField = PT5, "PTT5", 21, 1, 1, "" recordField = PT4, "PTT4", 20, 1, 1, "" recordField = PT3, "PTT3", 19, 1, 1, "" recordField = PT2, "PTT2", 18, 1, 1, "" recordField = PT1, "PTT1", 17, 1, 1, "" recordField = PT0, "PTT0", 16, 1, 1, "" recordField = PB7, "Spk H", 15, 1, 1, "" recordField = PB6, "Spk G", 14, 1, 1, "" recordField = PB5, "Spk F", 13, 1, 1, "" recordField = PB4, "Spk E", 12, 1, 1, "" recordField = PB3, "Spk D", 11, 1, 1, "" recordField = PB2, "Spk C", 10, 1, 1, "" recordField = PB1, "Spk B", 9, 1, 1, "" recordField = PB0, "Spk A", 8, 1, 1, "" recordField = PA7, "Inj H", 7, 1, 1, "" recordField = PA6, "Inj G", 6, 1, 1, "" recordField = PA5, "Inj F", 5, 1, 1, "" recordField = PA4, "Inj E", 4, 1, 1, "" recordField = PA3, "Inj D", 3, 1, 1, "" recordField = PA2, "Inj C", 2, 1, 1, "" recordField = PA1, "Inj B", 1, 1, 1, "" recordField = PA0, "Inj A", 0, 1, 1, "" calcField = mapValue, "MAP", "kPa", { map0 + (mapmax - map0) * mapAdc/1023 } loggerDef = mafLogger, "Engine Logger + MAF", csv dataReadCommand = "r\\x00\\xf8\\x00\\x00\\x04\\x00" ; standard TS command format dataReadTimeout = 10000 ; time in ms dataReadyCondition = { ( status3 & 0x02 ) == 0x02 } ;dataLength = 1024 ; in bytes, including headers, footers and data (not used) ;recordDef = headerLen. footerLen, recordLen recordDef = 0, 0, 4; in bytes, the recordLen is for each record, currently limited to 4 bytes ;recordField = Name, HeaderName, startBit, bitCount, scale, units, updateCondition recordField = mafAdc, "MAF ADC", 24, 8, 4.0, "ADC" ; scaled to 8 bits recordField = PT7, "PTT7", 23, 1, 1, "" recordField = PT6, "PTT6", 22, 1, 1, "" recordField = PT5, "PTT5", 21, 1, 1, "" recordField = PT4, "PTT4", 20, 1, 1, "" recordField = PT3, "PTT3", 19, 1, 1, "" recordField = PT2, "PTT2", 18, 1, 1, "" recordField = PT1, "PTT1", 17, 1, 1, "" recordField = PT0, "PTT0", 16, 1, 1, "" recordField = PB7, "Spk H", 15, 1, 1, "" recordField = PB6, "Spk G", 14, 1, 1, "" recordField = PB5, "Spk F", 13, 1, 1, "" recordField = PB4, "Spk E", 12, 1, 1, "" recordField = PB3, "Spk D", 11, 1, 1, "" recordField = PB2, "Spk C", 10, 1, 1, "" recordField = PB1, "Spk B", 9, 1, 1, "" recordField = PB0, "Spk A", 8, 1, 1, "" recordField = PA7, "Inj H", 7, 1, 1, "" recordField = PA6, "Inj G", 6, 1, 1, "" recordField = PA5, "Inj F", 5, 1, 1, "" recordField = PA4, "Inj E", 4, 1, 1, "" recordField = PA3, "Inj D", 3, 1, 1, "" recordField = PA2, "Inj C", 2, 1, 1, "" recordField = PA1, "Inj B", 1, 1, 1, "" recordField = PA0, "Inj A", 0, 1, 1, "" [TurboBaud] turboBaudOnCommand = "w\$tsCanId\x07\x02\x99\x00\x01\x51" turboBaudOffCommand = "w\$tsCanId\x07\x02\x99\x00\x01\x50" ; turboBaudSpeed defines the speed for ; TS to set the PC baud to when turboBaud is activated turboBaudSpeed = { baudhigh } ; reference the Constant so they will always be in sync with one setting. sdTurboActive = { 1 } ; this can reference a Constant or PcVariable in order to make it user selectable. runtimeTurboActive = { 0 } [Constants] ;---------------------------------------------------------------------------- ; Constants Definition ; -------------------- ; ; Scalar Values ; ------------- ; The scaling and translation values are used as follows: ; msValue = userValue / scale - translate ; userValue = (msValue + translate) * scale ; ; Array Values ; ------------ ; Arrays are specified just like scalars, except that they have a "shape" ; entry in the fourth parameter. The shape allows you to define lists or ; tables, for example [8] defines a list with eight values and [2x4] defines ; a table with eight values (two rows and four columns). Tables may be ; stored in either "X-" or "Y-order." X-order means that memory is layed ; out like. ; ; [x1,y1] [x2,y1]...[xn,y1] [x1,y2]... ; ; Y-order would be ; ; [x1,y1] [x1,y2]...[x1,yn] [x2,y1]... ; ; To use the TableEditor, you must define two lists and a table, and ; the lengths of the lists must correspond to the shape of the table. ; ; Bit Fields ; ---------- ; Bits are numbered 0-7, the rightmost being bit zero. The basic ; data word that stores bit fields must be unsigned. ; ; You need NOT supply the correct number of labels matching the ; number of bits you've specified (one bit requires 2 values, two ; bits requires 4 values and so on). If you neglect to supply enough ; labels, they will be synthesized using the sequence "1", "2" and so ; on based upon their position in the sequence (the cltType and matType ; will end up with identical lists). ; ;---------------------------------------------------------------------------- ; updated settings from "new" serial pageActivationDelay = 1 blockReadTimeout = 500 tsWriteBlocks = on ; writeBlocks = on interWriteDelay = 0 ;Relationship between TS pages and MS3 pages ;TS MS3 internal ;MS3 internal pages 0-3 are sensor lookup tables ;1 4 ;2 5 ;MS3 internal pages 6,7 are outpc,txbuf ;3 8 ;4 9 ;5 10 ;6 11 ;7 12 ;8 13 ;9 18 ;10 19 ;11 21 ;12 22 ;13 23 ;14 24 ;15 25 ;16 26 ; RAM only page ;17 27 ;18 28 endianness = big nPages = 18 pageSize = 1024, 1024, 1024, 1024, 1024, 1024, 1024, 1024, 1024, 1024, 1024, 1024, 1024, 1024, 1024, 1024, 1024, 1024 pageIdentifier = "\$tsCanId\x04", "\$tsCanId\x05", "\$tsCanId\x08", "\$tsCanId\x09", "\$tsCanId\x0a", "\$tsCanId\x0b", "\$tsCanId\x0c", "\$tsCanId\x0d", "\$tsCanId\x12", "\$tsCanId\x13", "\$tsCanId\x15", "\$tsCanId\x16", "\$tsCanId\x17", "\$tsCanId\x18", "\$tsCanId\x19", "\$tsCanId\x1a", "\$tsCanId\x1b", "\$tsCanId\x1c" burnCommand = "b%2i", "b%2i", "b%2i", "b%2i", "b%2i", "b%2i", "b%2i", "b%2i", "b%2i", "b%2i", "b%2i", "b%2i", "b%2i", "b%2i", "b%2i", "", "b%2i", "b%2i" pageReadCommand = "r%2i%2o%2c", "r%2i%2o%2c", "r%2i%2o%2c", "r%2i%2o%2c", "r%2i%2o%2c", "r%2i%2o%2c", "r%2i%2o%2c", "r%2i%2o%2c", "r%2i%2o%2c", "r%2i%2o%2c", "r%2i%2o%2c", "r%2i%2o%2c", "r%2i%2o%2c", "r%2i%2o%2c", "r%2i%2o%2c", "r%2i%2o%2c", "r%2i%2o%2c", "r%2i%2o%2c" pageValueWrite = "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v" pageChunkWrite = "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v", "w%2i%2o%2c%v" crc32CheckCommand = "k%2i\x00\x00\x00\x04", "k%2i\x00\x00\x00\x04", "k%2i\x00\x00\x00\x04", "k%2i\x00\x00\x00\x04", "k%2i\x00\x00\x00\x04", "k%2i\x00\x00\x00\x04", "k%2i\x00\x00\x00\x04", "k%2i\x00\x00\x00\x04", "k%2i\x00\x00\x00\x04", "k%2i\x00\x00\x00\x04", "k%2i\x00\x00\x00\x04", "k%2i\x00\x00\x00\x04", "k%2i\x00\x00\x00\x04", "k%2i\x00\x00\x00\x04", "k%2i\x00\x00\x00\x04", "k%2i\x00\x00\x00\x04", "k%2i\x00\x00\x00\x04", "k%2i\x00\x00\x00\x04" tableCrcCommand = "k\$tsCanId%2i%2o%2c" retrieveConfigError = "r\$tsCanId\x07\x04\x00\x00\xff" ; new serial messageEnvelopeFormat = msEnvelope_1.0 ; TS could use the 'F' command to determine this automatically. ;TS could use the 'f' command to determine this automatically. Will change if using CAN passthrough #if CAN_COMMANDS blockingFactor = 256 ; just in case MS2 is used #else blockingFactor = 2048 #endif validateArrayBounds = true page = 1 ; name = class, type, offset, shape, units, scale, translate, lo, hi, digits nCylinders = bits, U08, 0, [0:4], "INVALID","1","2","3","4","5","6","7","8","9","10","11","12","13","14","15","16","INVALID","INVALID","INVALID","INVALID","INVALID","INVALID","INVALID","INVALID","INVALID","INVALID","INVALID","INVALID","INVALID","INVALID","INVALID" no_skip_pulses = scalar, U08, 1, "", 1.00000, 0.00000, 1.00, 10.00, 0 ; * ( 1 byte) ICIgnCapture = bits, U08, 2, [0:0], "Falling Edge", "Rising Edge" ; ICIgnOption engineType = bits, U08, 2, [3:3], "Even fire", "Odd fire" ; old setting and settings spkout_hi_lo = bits, U08, 2, [4:4], "Going Low (Normal)", "Going High (Inverted)" ; * ; new settings spkout_hi_lo2 = bits, U08, 2, [4:4], "Going Low", "Going High" ; * max_coil_dur = scalar, U08, 3, "ms", 0.1000, 0.00000, 1.00, 8.00, 1 ; * ( 1 byte) max_spk_dur = scalar, U08, 4, "ms", 0.1000, 0.00000, 0.00, 25.50, 1 ; * ( 1 byte) ; dwellAcc = scalar, U08, 5, "ms", 0.1000, 0.00000, 0.00, 25.50, 0 ; * ( 1 byte) crankingRPM = scalar, S16, 6, "RPM", 1.00000, 0.00000, 200, 3000.0, 0 ; * ( 2 bytes) triggerOffset = scalar, S16, 8, "deg", 0.10000, 0.00000, -90.0, 380.00, 1 ; * ( 2 bytes) TpsBypassCLTRevlim = scalar, S16, 10, "TPS %", 0.10000, 0.00000, 0, 120, 1 ; * ( 2 bytes) ; RevLimRpm2 = scalar, S16, 12, "RPM", 1.00000, 0.00000, 0.00,{rpmhigh}, 0 ; * ( 2 bytes) map0 = scalar, S16, 14, "%", 0.10000, 0.00000, -3276.8, 3276.7, 1 ; * ( 2 bytes) mapmax = scalar, S16, 16, "%", 0.10000, 0.00000, -3276.8, 3276.7, 1 ; * ( 2 bytes) #if CELSIUS clt0 = scalar, S16, 18, "°C", 0.05555, -320.000, -100.0, 500.0, 1 ; * ( 2 bytes) cltmult = scalar, S16, 20, "%", 1.00000, 0.00000, -200.0, 200.0, 0 ; * ( 2 bytes) mat0 = scalar, S16, 22, "°C", 0.05555, -320.000, -100.0, 500.0, 1 ; * ( 2 bytes) #else clt0 = scalar, S16, 18, "°F", 0.10000, 0.00000, -100.0, 500.0, 1 cltmult = scalar, S16, 20, "%", 1.00000, 0.00000, -200.0, 200.0, 0 mat0 = scalar, S16, 22, "°F", 0.10000, 0.00000, -100.0, 500.0, 1 #endif matmult = scalar, S16, 24, "%", 1.00000, 0.00000, -200.0, 200.0, 0 ; * ( 2 bytes) tpsMin = scalar, S16, 26, "ADC", 1.00000, 0.00000, 0, 1023, 0 ; * ( 2 bytes) tpsMax = scalar, S16, 28, "ADC", 1.00000, 0.00000, 0, 1023, 0 ; * ( 2 bytes) batt0 = scalar, S16, 30, "V", 0.10000, 0.00000, -10, 10, 1 ; ( 2 bytes) battmax = scalar, S16, 32, "V", 0.10000, 0.00000, 10, 100, 1 ; ( 2 bytes) ego0 = scalar, S16, 34, "afr", 0.10000, 0.00000,-3276.8, 3276.7, 1 ; ( 2 bytes) egomult = scalar, S16, 36, "%", 1.00000, 0.00000, -200.0, 200.0, 0 ; ( 2 bytes) baro0 = scalar, S16, 38, "kPa", 0.10000, 0.00000,-3276.8, 3276.7, 1 ; * ( 2 bytes) baromax = scalar, S16, 40, "kPa", 0.10000, 0.00000,-3276.8, 3276.7, 1 ; * ( 2 bytes) bcor0 = scalar, S16, 42, "%", 1.00000, 0.00000,-3276.8, 3276.7, 1 ; * ( 2 bytes) bcormult = scalar, S16, 44, "%", 1.00000, 0.00000, -200.0, 200.0, 0 ; * ( 2 bytes) iacfullopen = scalar, U16, 46, "steps", 1.00000, 0.00000, 0.0, 4000.0, 0 reluctorteeth1 = scalar, U16, 48, "", 0.01, 0,0,255,2 ; this is VSS1 crankTolerance = scalar, U08, 50, "%", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) asTolerance = scalar, U08, 51, "%", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) pulseTolerance = scalar, U08, 52, "%", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) ; IdleCtl = bits , U08, 53, [0:3], "None", "On/Off valve", "IAC Stepper Moving Only", "IAC Stepper Always On", "PWM Warmup", "15-Minute IAC", "PWM Closed-loop", "IAC Closed-loop moving only", "IAC Closed-loop always-on", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" ; * IdleCtl = bits , U08, 53, [0:1], "None", "On/Off valve", "PWM valve (2 or 3 wire)", "Stepper valve (4 or 6 wire)" IdleCtl_alg = bits , U08, 53, [3:3], "Open-loop (warmup)", "Closed-loop" IdleCtl_vss = bits , U08, 53, [4:4], "Standard", "Use VSS" IdleCtl_home = bits , U08, 53, [5:5], "Closed", "Open" IACtstep = scalar, U08, 54, "ms", 1.000, 0.00000, 0.00, 25, 0 ; * ( 1 byte) IAC_tinitial_step=scalar, U08, 55, "ms", 1.000, 0.00000, 0.00, 25, 0 ; * ( 1 byte) IACminstep = scalar, U08, 56, "steps", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) dwellduty = scalar, U08, 57, "%", 0.39, 0.0, 0, 100,0 IACStart = scalar, S16, 58, "", 1.00000, 0.00000, 0.00, 4000.00, 0 #if CELSIUS IdleHyst = scalar, S16, 60, "°C", 0.05555, 0.00000, -40.0, {clthighlim}, 1 ; * ( 2 bytes) #else IdleHyst = scalar, S16, 60, "°F", 0.10000, 0.00000, -40.0, {clthighlim}, 1 #endif IACcrankpos = scalar, S16, 62, "steps", 1.00000, 0.00000, 0.00, 4000.00, 0 ; * ( 2 bytes) IACcrankxt = scalar, S16, 64, "s", 1.00000, 0.00000, 0.00,32767.00, 0 ; * ( 2 bytes) IACcurlim = bits, U08, 66, [0:1], "Moving only", "Hold current", "Always on", "INVALID" ;gap reluctorteeth2 = scalar, U16, 68, "", 0.01, 0,0,255,2 ; this is VSS2 boosttol = scalar, S16, 70, "kPa", 0.10000, 0.00000, 0.00, 50, 1 OverBoostKpa2 = scalar, S16, 72, "kPa", 0.10000, 0.00000, 0.00, {loadhigh}, 1 fc_rpm_lower = scalar, U16, 74, "rpm", 1.00000, 0.0, 0.0, {rpmhigh}, 0 ; * ( 1 byte) OverBoostOption = bits, U08, 76, [0:1], "None", "Fuel Cut", "Spark Cut", "Both" OverBoostOption_tol = bits, U08, 76, [2:2], "Off", "On" hardware_spk = bits, U08, 77, [0:2], "JS10 spark", "LEDs spark", "MS3X spark", "INVALID", "Tacho", "INVALID", "INVALID", "INVALID" hardware_fuel = bits, U08, 77, [4:4], "Std fuel", "MS3X fuel" hardware_injij = bits, U08, 77, [5:5], "Mainboard", "H3+H4" hardware_cam = bits, U08, 77, [6:7], "JS10", "MS3X Cam in", "MAP sensor", "INVALID" OverBoostKpa = scalar, S16, 78, "kPa", 0.10000, 0.00000, 0.00, {loadhigh}, 1 OverBoostHyst = scalar, S16, 80, "kPa", 0.10000, 0.00000, 0.00, 100, 1 ; overboostcutx = scalar, U08, 82, "", 1, 0, 0, 255, 0 ; overboostcuty = scalar, U08, 83, "", 1, 0, 0, 255, 0 tpsThresh = scalar, S16, 84, "%/s", 0.10000, 0.00000, 0.00, 3276.0, 1 ; * ( 2 byte) mapThresh = scalar, S16, 86, "kPa/s", 1.00000, 0.00000, 0.00, 10000.0, 0 ; * ( 2 byte) threshold for MAE taeColdA = scalar, U08, 88, "%ReqFuel", 1, 0.00000, 0, 255, 0 ; * ( 1 byte) ; Tpsacold taeColdM = scalar, U08, 89, "%", 1.00000, 0.00000, 100, 255.00, 0 ; * ( 1 byte) ; AccMult taeTime = scalar, U08, 90, "s", 0.010000, 0.00000, 0.00, 1.00, 2 ; * ( 1 byte) ; TpsAsync tpsasync_events = scalar, U08, 90, "events", 1, 0.00000, 0.00, 255, 0 ; * ( 1 byte) ; TpsAsync tdePct = scalar, U08, 91, "", 1.00000, 0.00000, 50.00, 100.00, 0 ; * ( 1 byte) ; TPSDQ floodClear = scalar, S16, 92, "%", 0.10000, 0.00000, 0.00, 100.00, 1 ; * ( 2 bytes) ; TPSWOT TPSOXLimit = scalar, S16, 94, "%", 0.10000, 0.00000, 0.00, 300.00, 1 ; * ( 2 bytes) ; TPSOXLimit tpsProportion = scalar, U08, 96, "%", 1.00000, 0.00000, 0.00, 100.00, 0 ; * ( 1 byte) ; Tps_acc_wght baroCorr = bits , U08, 97, [0:1], "None", "Initial MAP Reading", "Two Independent Sensors", "INVALID"; BaroOption egoType = bits , U08, 98, [0:1], "Disabled", "Narrow Band", "Wide Band", "INVALID" ; egoOption egoCount = scalar, U08, 99, "", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) egoDelta = scalar, U08, 100, "%", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) oldegoLimit = scalar, U08, 101, "%", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) EGOVtarget = scalar, U08, 102, "Volts", 0.00489, 0.00000, 0.00, 1, 3 tempUnits = bits , U08, 103, [0:0], "Coolant/MAT Tables in °F", "Coolant/MAT Tables in °C" ; * ( 1 byte) egonum = scalar, U08, 104, "", 1, 0, 0, 16, 0 rtc_trim = scalar, S08, 105, "ppm", 1, 0, -127, +127, 0 #if CELSIUS fastIdleT = scalar, S16, 106, "°C", 0.05555, -320.000,-40.00, {clthighlim}, 1 ; * ( 2 bytes) egoTemp = scalar, S16, 108, "°C", 0.05555, -320.000,-40.00, {clthighlim}, 1 ; * ( 2 bytes) #else fastIdleT = scalar, S16, 106, "°F", 0.10000, 0.00000,-40.00, {clthighlim}, 1 egoTemp = scalar, S16, 108, "°F", 0.10000, 0.00000,-40.00, {clthighlim}, 1 #endif egoRPM = scalar, U16, 110, "RPM", 1.00000, 0.00000, 0.00, {rpmhigh}, 0 ; RPMOXLimit #if PW_4X reqFuel = scalar, U16, 112, "ms", 0.004, 0.00000, 0.00, 262.143, 2 ; * ( 2 bytes) #else reqFuel = scalar, U16, 112, "ms", 0.001, 0.00000, 0.00, 65.535, 2 ; * ( 2 bytes) #endif divider = scalar, U08, 114, "", 1.00000, 0.00000, 0.00, 255, 0 ; * ( 1 byte) alternate = bits, U08, 115, [0:0], "Simultaneous", "Alternating" ; * ( 1 byte) altcrank = bits, U08, 115, [1:1], "Every event", "Alternate events" alternate_blend = bits, U08, 115, [2:2], "Off", "Blend Curve (7)" injPwmT = scalar, U08, 116, "ms", 0.12800, 0.128, 0.00, 32.64, 1 ; * ( 1 byte) injPwmPd = scalar, U08, 117, "us", 1.00000, 0.00000, 40.00, 100.00, 0 ; * ( 1 byte) injPwmP = scalar, U08, 118, "%", 1.00000, 0.00000, 0.00, 100.00, 0 ; * ( 1 byte) twoStroke = bits, U08, 119, [0:1], "Four-stroke", "Two-stroke", "INVALID", "Rotary" ; * ; injType = bits, U08, 120, [0:0], "Port Injection", "Throttle Body" ; * not used by code nInjectors = bits, U08, 121, [0:4], "INVALID", "1", "2", "3", "4", "5", "6", "7", "8", "9", "10", "11", "12", "13", "14", "15", "16", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" OddFireang = scalar, U16, 122, "", 0.10000, 0.00000, 0.00, 720.00, 0 ; * ( 2 byte) rpmLF = scalar, U08, 124, "", 1.00000, 0.00000, 10.00, 100.00, 0 ; * ( 1 byte) mapLF = scalar, U08, 125, "", 1.00000, 0.00000, 10.00, 100.00, 0 ; * ( 1 byte) tpsLF = scalar, U08, 126, "", 1.00000, 0.00000, 10.00, 100.00, 0 ; * ( 1 byte) egoLF = scalar, U08, 127, "", 1.00000, 0.00000, 10.00, 100.00, 0 ; * ( 1 byte) adcLF = scalar, U08, 128, "", 1.00000, 0.00000, 10.00, 100.00, 0 ; * ( 1 byte) knk_pin_out = bits, U08, 129, [0:5], "Off", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" mafLF = scalar, U08, 130, "", 1.00000, 0.00000, 10.00, 100.00, 0 ;gap algorithm = bits, U08, 132, [0:3], "INVALID", "Speed Density", "Percent Baro", "Alpha-N", "INVALID", "MAF", "ITB", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" ; * algorithm2 = bits, U08, 132, [4:7], "Disabled", "Speed Density", "Percent Baro", "Alpha-N", "INVALID", "MAF", "ITB", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" IgnAlgorithm = bits, U08, 133, [0:3], "INVALID", "Speed Density", "Percent Baro", "Alpha-N", "INVALID", "MAF", "ITB", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" IgnAlgorithm2 = bits, U08, 133, [4:7], "Disabled", "Speed Density", "Percent Baro", "Alpha-N", "INVALID", "MAF", "ITB", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" AfrAlgorithm = scalar, U08, 134, "", 1.00000, 0.00000, 0.00, 255.00, 0 ; U ( 1 byte) UNUSED dwelltime = scalar, U08, 135, "ms", 0.10000, 0, 0.1, 25.5, 1 trigret_ang = scalar, U16, 136, "deg", 0.1, 0, 5, 180,1 RevLimOption_retard = bits,U08, 138, [0:1], "Off", "Progressive retard", "Fixed angle", "INVALID" RevLimOption_spkcut = bits,U08, 138, [2:2], "Off", "On" RevLimCLTbased = bits, U08, 138, [3:3], "Normal", "CLT based" RevLimOption_fuelprog=bits,U08, 138, [4:4], "Off", "On" RevLimOption_fuelcut =bits,U08, 138, [5:5], "Off", "On" RevLimMaxRtd = scalar, U08, 139, "deg", 0.10000, 0.00000,0, 25.5, 0 ; * ( 1 byte) ego_startdelay = scalar, U08, 140, "s", 1, 0, 0, 120, 0 can_poll2_ego = bits, U08, 141, [0:0], "Disable", "Enable" can_poll2_gps = bits, U08, 141, [1:2], "Off", "JBperf GPS", "INVALID", "INVALID" opt142_rtc = bits, U08, 142, [0:1], "Off", "On-board", "CAN", "INVALID" opt142_gs_share = bits, U08, 142, [2:2], "Off", "On" injPwmT2 = scalar, U08, 143, "ms", 0.12800, 0.12800, 0.00, 32.64, 1 ; * ( 1 byte) injPwmPd2 = scalar, U08, 144, "us", 1.00000, 0.00000, 40.00, 100.00, 0 ; * ( 1 byte) injPwmP2 = scalar, U08, 145, "%", 1.00000, 0.00000, 0.00, 100.00, 0 ; * ( 1 byte) can_ego_id = scalar, U08, 146, "", 1.00000, 0.00000, 0.00, 14, 0 ; can_ego_table = scalar, U08, 147, "", 1.00000, 0.00000, 0, 15, 0 ; * ( 1 byte) can_ego_offset = scalar, U16, 148, "bytes", 1.00000, 0.00000, 0, 4095, 0 baro_upper = scalar, S16, 150, "kPa", 0.10000, 0.00000, 60, {loadhigh}, 1 ; baro_lower = scalar, S16, 152, "kPa", 0.10000, 0.00000, 60, {loadhigh}, 1 ; baro_default = scalar, S16, 154, "kPa", 0.10000, 0.00000, 60, {loadhigh}, 1 ; RevLimTPSbypassRPM = scalar, S16, 156, "RPM", 1.00000, 0.00000, 0.00, {rpmhigh}, 0 ; ; RevLimNormal1 = scalar, S16, 158, "RPM", 1.00000, 0.00000, 0.00, {rpmhigh}, 0 ; RevLimNormal2 = scalar, S16, 160, "RPM", 1.00000, 0.00000, 0.00, {rpmhigh}, 0 ; hw_latency = scalar, U08, 162, "usec", 1.0, 0.00000, 0.00, 255.00, 0 ;next three are loadopts in the firmware loadCombine = bits, U08, 163, [0:1], "additive", "multiplicitive", "Blend Curve (1)", "INVALID" loadMult = bits, U08, 163, [2:2], "don't multiply", "multiply" loadStoich = bits, U08, 163, [3:3], "don't include AFRtarget", "include AFRtarget" loadCombineign = bits, U08, 163, [4:4], "additive", "Blend Curve (2)" loadMult2 = bits, U08, 163, [5:5], "don't multiply", "multiply" ; baud = scalar, U32, 164, "", 1.00000, 0.00000,9600.0,115200.0, 0 ; x ( 4 bytes) baud = scalar, U32, 164, "", 1.00000, 0.00000,9600.0,500000.0, 0 ; x ( 4 bytes) MAPOXLimit = scalar, S16, 168, "%", 0.10000, 0.00000, 0.00, 300.00, 2 ; * ( 2 bytes) can_poll_id_rtc = scalar, U08, 170, "", 1.00000, 0.00000, 0.00, 14, 0 mycan_id = scalar, U08, 171, "", 1.00000, 0.00000, 0.00, 14, 0 mapsample_percent = scalar, U08, 172, "%", 1.00000, 0.00000, 0.00, 50, 0 can_poll_id_ports = scalar, U08, 173, "", 1.00000, 0.00000, 0.00, 14, 0 ; can_poll_id = scalar, U08, 174, "", 1.00000, 0.00000, 0.00, 14, 0 ; aeTaperTime = scalar, U08, 175, "s", 0.010000, 0.00000, 0.00, 1.00, 2 ; * ( 1 byte) ; TpsAsync2 tpsasync2_events= scalar, U08, 175, "events", 1, 0.00000, 0.00, 255, 0 ; * ( 1 byte) ; TpsAsync2 aeEndPW = scalar, S16, 176, "%ReqFuel", 1, 0.00000, 0.00, 100, 0 ; * tpsaccel2 ; TpsAccel2 egoAlgorithm = bits , U08, 178, [0:1], "Simple", "INVALID", "PID", "No correction" ; * ( 1 byte) egoAlgorithm_auth=bits , U08, 178, [2:2], "Off", "On" egoAlgorithm_delay_table=bits, U08, 178, [3:3], "Use IGN events", "Use delay table" egoKP = scalar, U08, 179, "%", 1.00000, 0.00000, 0.00, 200.00, 0 ; * ( 1 byte) egoKI = scalar, U08, 180, "%", 1.00000, 0.00000, 0.00, 200.00, 0 ; * ( 1 byte) egoKD = scalar, U08, 181, "%", 1.00000, 0.00000, 0.00, 200.00, 0 ; * ( 1 byte) ac_idleup_vss_offpoint = scalar, U16, 182, { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, { msToPrefUnitsScale }, 0.00000, 0.00, 200, 0 ; * ( 2 bytes) ac_idleup_vss_hyst = scalar, U16, 184, { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, { msToPrefUnitsScale }, 0.00000, 0.00, 200, 0 ; * ( 2 bytes) flexFuel = bits , U08, 186, [0:0], "Disabled", "Enabled" ; * ( 1 byte) flexport = bits, U08, 186, [1:2], "PE0/JS7", "JS11", "Flex input", "INVALID"; (1 byte ) fuelFreq = array , U08, 187, [ 2], "Hz", 1.00000, 0.00000, 0.00, 255, 0 ; * ( 2 bytes) fuelFreq0 = scalar, U08, 187, "Hz", 1.00000, 0.00000, 0.00, 255, 0 fuelFreq1 = scalar, U08, 188, "Hz", 1.00000, 0.00000, 0.00, 255, 0 fuelCorr = array , U08, 189, [ 2], "%", 1.00000, 0.00000, 50, 255, 0 ; * ( 2 bytes) fuelCorr0 = scalar, U08, 189, "%", 1.00000, 0.00000, 50, 255, 0 fuelCorr1 = scalar, U08, 190, "%", 1.00000, 0.00000, 50, 255, 0 dwellmode = bits , U08, 191, [0:1], "Standard Dwell", "Fixed Duty", "Time after Spark", "Charge at Trigger" pwmidle_shift_lower_rpm = scalar, U16, 192, "rpm", 1.00000, 0.00000, 0.00, {rpmhigh}, 0 ac_idleup_tps_offpoint = scalar, S16, 194, "%", 0.10000, 0.00000, 0.00, 100.00, 1 ac_idleup_tps_hyst = scalar, S16, 196, "%", 0.10000, 0.00000, 0.00, 100.00, 1 fan_idleup_tps_offpoint = scalar, S16, 198, "%", 0.10000, 0.00000, 0.00, 150.00, 1 fan_idleup_tps_hyst = scalar, S16, 200, "%", 0.10000, 0.00000, 0.00, 100.00, 1 fan_idleup_vss_offpoint = scalar, U16, 202, { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, { msToPrefUnitsScale }, 0.00000, 0.00, 200.00, 0 knk_option = bits , U08, 204, [0:1], "Disabled", "Safe Mode", "Aggressive Mode", "INVALID" ; * ( 1 byte ) knk_option_an = bits , U08, 204, [2:3], "On/Off", "Analogue", "INVALID", "Internal" knkDirection = bits , U08, 204, [4:4], "Low Input", "High Input" ; * knkpull = bits , U08, 204, [5:6], "INVALID", "None", "Pull up", "INVALID" ; * knk_option_wind = bits , U08, 204, [7:7], "At end", "Peak" knk_maxrtd = scalar, U08, 205, "deg", 0.1, 0.0, 0.0, 25.5, 1 ; * ( 1 byte ) knk_step1 = scalar, U08, 206, "deg", 0.1, 0.0, 1.0, 25.5, 1 ; * ( 1 byte ) knk_step2 = scalar, U08, 207, "deg", 0.1, 0.0, 0.5, 10.0, 1 ; * ( 1 byte ) knk_trtd = scalar, U08, 208, "s", 0.1, 0.0, 0.0, 25.5, 1 ; * ( 1 byte ) knk_tadv = scalar, U08, 209, "s", 0.1, 0.0, 0.0, 25.5, 1 ; * ( 1 byte ) knk_dtble_adv = scalar, U08, 210, "deg", 0.1, 0.0, 0.0, 25.5, 1 ; * ( 1 byte ) knk_ndet = scalar, U08, 211, "knocks", 1.0, 0.0, 0.0, 255, 0 ; * ( 1 byte ) EAEOption = bits , U08, 212, [0:2], "Off", "EAE", "INVALID", "X-tau", "X-tau with CLT correction", "INVALID", "INVALID", "INVALID" ; * ( 1 byte ) knkport = bits, U08, 213, [0:3], "INVALID", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)","INVALID","INVALID" knk_maxmap = scalar, S16, 214, "kPa", 0.1, 0.0, 0.0, {loadhigh}, 1 ; * ( 2 bytes) knk_lorpm = scalar, U16, 216, "rpm", 1.0, 0.0, 0.0, {rpmhigh}, 0 ; * ( 2 bytes) knk_hirpm = scalar, U16, 218, "rpm", 1.0, 0.0, 0.0, {rpmhigh}, 0 ; * ( 2 bytes) triggerTeeth = scalar, U16, 220, "teeth", 1.0, 0.0, 2, 255, 0 ; * ( 2 bytes) No_Miss_Teeth = scalar, U08, 222, "teeth", 1.0, 0.0, 0.0, 4, 0 ; * ( 1 byte ) pwmidle_shift_open_time = scalar, U08, 223, "s", 1.0, 0.0, 0.0, 20, 0 ; * ( 1 byte ) Miss_ang = scalar, U16, 224, "deg BTDC", 0.1, 0.0, 0.0, 720, 1 ; * ( 2 bytes ) ICISR_tmask = scalar, U08, 226, "ms", 0.1, 0.0, 0.0, 25.5, 1 ; * ( 1 byte ) ICISR_pmask = scalar, U08, 227, "%", 1.0, 0.0, 0.0, 90, 0 ; * ( 1 byte ) ae_lorpm = scalar, U16, 228, "rpm", 1.0, 0.0, 0.0, {rpmhigh}, 0 ; * ( 2 bytes) ae_hirpm = scalar, U16, 230, "rpm", 1.0, 0.0, 0.0, {rpmhigh}, 0 ; * ( 2 bytes) fuelSpkDel = array , S16, 232, [ 2], "deg", 0.10000, 0.00000,-45.00, 45.00, 1 ; * ( 4 bytes) fuelSpkDel0 = scalar, S16, 232, "deg", 0.10000, 0.00000,-45.00, 45.00, 1 fuelSpkDel1 = scalar, S16, 234, "deg", 0.10000, 0.00000,-45.00, 45.00, 1 spk_conf2_gmtfi = bits , U08, 236, [0:2], "Off", "GM Bypass on SpkB", "Buick C3I", "TFI Non-signature", "TFI Signature PIP", "INVALID", "INVALID", "INVALID" spk_conf2_oddodd= bits , U08, 236, [3:4], "Alternate", "INVALID", "Paired", "Custom" spk_conf2_dwell = bits , U08, 236, [5:5], "Off", "On" spk_conf2_dwelltbl = bits, U08, 236, [6:6], "Off", "On" spk_conf2_dli = bits , U08, 236, [7:7], "Off", "Toyota DLI" ;spk_config spk_config_campol =bits, U08, 237, [0:0], "Low", "High" spk_config_camcrank = bits, U08, 237, [1:1], "Crank wheel", "Cam wheel" spk_config_trig2 =bits, U08, 237, [2:3], "INVALID", "Single wheel with missing tooth", "Dual wheel", "Dual wheel with missing tooth" spk_config_trig2l =bits, U08, 237, [4:5], "INVALID", "Rising edge", "Falling edge", "Poll level" spk_config_resetcam =bits, U08, 237, [6:7], "Cam", "Crank", "Every cylinder", "INVALID" ; invalids in next line are spare and should be used, extra CASes hidden. spk_mode0 = bits , U08, 238, [0:5], "EDIS", "EDIS Multispk", "Basic trigger", "Trigger return", "Toothed wheel", "420A/Neon", "36-2+2", "36-2-2-2", "Subaru 6/7", "Miata 99-05", "6g72", "IAW Weber", "CAS 4/1", "4G63", "Twin trigger", "Chrysler 2.2/2.5", "Renix 44-2-2", "Suzuki Swift", "Suzuki Vitara 2.0", "Daihatsu 3cyl", "Daihatsu 4cyl", "VTR1000", "Rover#1", "Rover#2", "Rover#3", "GM 7X", "Log crank", "Log crank&cam", "QR25DE", "Honda RC51", "Fiat 1.8 16V", "Fuel Only", "Optispark", "Nissan SR20", "Nissan RB25", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID","LS1", "YZF1000", "Honda Acura", "VQ35DE","Jeep 2000", "Jeep 2002", "Zetec VCT", "Flywheel tri-tach", "2JZ VVTi", "Honda TSX/D17", "Mazda6 2.3 VVT", "Viper V10","Viper V10 Gen1", "Honda K24A2", "HD32-2", "Miata 36-2","INVALID", "INVALID", "INVALID", "INVALID","INVALID", "INVALID", "INVALID", "INVALID" ; incomplete modes are hidden for the moment spk_mode3_trim = bits, U08, 239, [0:0], "Off", "On" spk_mode3_tach3 = bits, U08, 239, [1:1], "MS3X Cam", "JS10" spk_mode3_hirespol= bits, U08, 239, [2:2], "Normal", "Inverted" spk_mode3 = bits, U08, 239, [5:7], "Single coil", "INVALID", "Wasted spark", "Wasted COP", "Coil on plug", "INVALID", "Dual dizzy", "INVALID" ; (1 byte ) rtbaroport = bits, U08, 240, [0:4], "Mainboard", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" ego2port = bits, U08, 241, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" mapport = bits, U08, 242, [0:4], "Mainboard", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" mapport_t = bits, U08, 242, [5:6], "Voltage", "Frequency", "Off", "INVALID" ;NB these mapport are in next byte mapport_f = bits, U08, 243, [6:7], "PT4", "MS3X cam PT2", "JS10 PT5", "Datalog PT6" knkport_an = bits, U08, 243, [0:2], "INVALID", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", OvrRunC = bits , U08, 244, [0:0], "Off", "On" OvrRunC_progcut= bits , U08, 244, [1:1], "Off", "On" OvrRunC_progret= bits , U08, 244, [2:2], "Off", "On" OvrRunC_progign= bits , U08, 244, [3:3], "Off", "On" OvrRunC_retign = bits , U08, 244, [4:4], "Off", "On" poll_level_tooth = scalar, U08, 245, "", 1, 0, 0, 255, 0 ; feature4_0ftrig = bits, U08, 246, [0:0], "Simple", "Advanced" feature4_0igntrig= bits, U08, 246, [1:1], "Off", "Ignition trigger indicator" feature4_0maxdwl = bits, U08, 246, [3:3], "Off", "On" feature4_0ftrig = bits, U08, 246, [4:5], "Off", "INVALID", "Simple", "Advanced" feature4_0mindwl = bits, U08, 246, [6:6], "Off", "On" timing_flags = bits, U08, 247, [0:0], "Use Table", "Fixed timing"; use_prediction = bits, U08, 247, [1:1], "No Prediction", "1st Deriv Prediction"; crank_dwell = scalar, U08, 248, "ms", 0.1000,0.00000,1.00,8.00,1 tsw_pin_f = bits, U08, 249, [0:4], "INVALID", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "Blend Curve (3)", "INVALID", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" crank_timing = scalar, S16, 250, "degrees", 0.10000,0.00000,-10.00,90.00,1; fixed_timing = scalar, S16, 252, "degrees", 0.10000,0.00000,-90.00,90.00,1; tsf_rpm = scalar, U16, 254, "rpm", 1, 0, 0, {rpmhigh}, 0 tsf_kpa = scalar, S16, 256, "kPa", 0.1, 0, 0, {loadhigh}, 1 tsf_tps = scalar, S16, 258, "%", 0.10000, 0.00000, 0.00, 100.00, 1; tss_rpm = scalar, U16, 260, "rpm", 1, 0, 0, {rpmhigh}, 0 tss_kpa = scalar, S16, 262, "kPa", 0.1, 0, 0, {loadhigh}, 1 tss_tps = scalar, S16, 264, "%", 0.10000, 0.00000, 0.00, 100.00, 1; ; feature5_0 266 f5_0_tsf = bits , U08, 266, [1:1], "Off", "On" f5_0_tsf_opt = bits , U08, 266, [2:3], "Hardware", "rpm", "kPa", "TPS" f5_0_tss = bits , U08, 266, [4:4], "Off", "On" f5_0_tss_opt = bits , U08, 266, [5:6], "Hardware", "rpm", "kPa", "TPS" tsw_pin_s = bits, U08, 267, [0:4], "INVALID", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "Blend Curve (4)", "INVALID", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" pwmidlecranktaper= scalar, U08, 268, "s", 1.00000, 0.00000, 0.00, 100.00, 0 knk_step_adv = scalar, U08, 269, "deg", 0.1, 0.0, 0.5, 10.0, 1 ; * ( 1 byte ) fc_rpm = scalar, U16, 270, "rpm", 1, 0, 0, {rpmhigh}, 0 fc_kpa = scalar, S16, 272, "kPa", 0.1, 0, 0, {loadhigh}, 1 fc_tps = scalar, S16, 274, "%", 0.10000, 0.00000, 0.00, 10.00, 1; #if CELSIUS fc_clt = scalar, S16, 276, "°C", 0.05555, -320.000, -40.0, {clthighlim}, 1 ; * ( 2 bytes) #else fc_clt = scalar, S16, 276, "°F", 0.10000, 0.00000, -40.0, {clthighlim}, 1 #endif fc_delay = scalar, U08, 278, "s", 0.1, 0, 0.5, 5.0, 1 tacho_opt80 = bits, U08, 279, [7:7], "Off", "On" tacho_opt40 = bits, U08, 279, [6:6], "Normal", "Half speed" tacho_opt3f = bits, U08, 279, [0:5], "INVALID", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" fc_ego_delay = scalar, U08, 280, "s", 1, 0, 0.00, 10, 0 EAElagsource = bits, U08, 281, [0:0], "TPSdot", "MAPdot" EAElagthresh = scalar, S16, 282, "unit/sec", 1, 0, 0.00, 1000, 0 EAElagRPMmax = scalar, U16, 284, "rpms", 1, 0, 0.00, {rpmhigh}, 0 feature3_tps = bits, U08, 286, [0:0], "Off", "On" feature3_aseunit= bits, U08, 286, [1:1], "Cycles", "0.1 seconds" feature3_maplog = bits, U08, 286, [2:2], "Off", "On" feature3_3 = bits, U08, 286, [3:3], "Off", "On" feature3_pw4x = bits, U08, 286, [4:4], "Normal", "4x" feature3_n2oin = bits, U08, 286, [5:5], "On", "Off" feature3_matase = bits, U08, 286, [6:6], "Off", "On" feature3_dwell = bits, U08, 286, [7:7], "Off", "On" launch_opt_vss = bits, U08, 287, [0:1], "Off", "VSS1", "VSS2", "INVALID" launch_opt_vssgear = bits, U08, 287, [2:2], "Off", "On" launch_opt_retard = bits, U08, 287, [3:3], "Off", "On" launch_opt_bank = bits, U08, 287, [4:5], "Off","Bank1", "Bank2", "Both" launch_opt_on = bits, U08, 287, [6:7], "Off", "Launch","INVALID","Launch/Flatshift" launch_sft_zone = scalar, S16, 288, "RPM", 1.00000, 0.00000, 100, 2000, 0 ; * ( 2 bytes) launch_sft_deg = scalar, S16, 290, "deg", 0.10000, 0.00000, -90.0, 180.00, 2 ; * ( 2 bytes) launch_hrd_lim = scalar, S16, 292, "RPM", 1.00000, 0.00000, 0.00, {rpmhigh}, 0 ; * ( 2 bytes) launch_tps = scalar, S16, 294, "%", 0.10000, 0.00000, 0.0, 100.00, 0 ; launchlimopt = bits , U08, 296, [0:1], "None", "Spark Cut", "Fuel Cut", "Spark and fuel" ; * ( 1 byte) launchvsstime = scalar, U08, 297, "s", 1, 0, 0, 255, 0 launchvss_maxgear= scalar, U08, 298, "", 1, 0, 1, 6, 0 launch_opt_pins = bits, U08, 299, [0:4], "INVALID", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "INVALID", "INVALID", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" flats_arm = scalar, U16, 300, "RPM", 1.00000, 0.00000, 0.00, {rpmhigh}, 0 launchvss_minvss = scalar, U16, 302, { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, { msToPrefUnitsScale }, 0.00000, 1, 200, 1 flats_deg = scalar, S16, 304, "deg", 0.10000, 0.00000, -90.0, 180.00, 2 ; * ( 2 bytes) flats_hrd = scalar, U16, 306, "RPM", 1.00000, 0.00000, 0.00, {rpmhigh}, 0 ; * ( 2 bytes) staged_pri_size = scalar, U16, 308, "cc", 1.00000, 0.00000, 0.0000, 15000.0, 0 ; * ( 2 bytes) staged_sec_size = scalar, U16, 310, "cc", 1.00000, 0.00000, 0.0000, 15000.0, 0 ; * ( 2 bytes) staged_first_param = bits, U08, 312, [0:2], "Off", "RPM", "MAP", "TPS", "Duty", "Table", "INVALID", "INVALID" staged_second_param = bits, U08, 312, [3:5], "Off", "RPM", "MAP", "TPS", "Duty", "INVALID", "INVALID", "INVALID" staged_transition_on = bits, U08, 312, [6:6], "Off", "On" staged_second_logic = bits, U08, 312, [7:7], "OR", "AND" staged_pw1_0 = bits, U08, 312, [7:7], "Off", "On" staged_transition_events = scalar, U08, 313, "ign events", 1.00000, 0.00000, 0.00, 255.0, 0 staged_param_1 = scalar, S16, 314, "units", 1.00000, 0.00000, 0.00, 25500.0, 0 staged_param_2 = scalar, S16, 316, "units", 1.00000, 0.00000, 0.00, 25500.0, 0 staged_hyst_1 = scalar, S16, 318, "units", 1.00000, 0.00000, 0.00, 25500.0, 0 staged_hyst_2 = scalar, S16, 320, "units", 1.00000, 0.00000, 0.00, 25500.0, 0 ; Nitrous System N2Oopt_01 = bits, U08, 322,[0:1],"INVALID","Bank1", "Bank2", "Both" N2Oopt_2 = bits, U08, 322,[2:2], "Off", "On" ; enables stage 1 N2Oopt_3 = bits, U08, 322,[3:3], "Off", "On" ; enables stage 2 N2Oopt_4 = bits, U08, 322,[4:4], "Off", "On" ; use AFR2 ;input and output pins moved N2Oopt2_prog = bits, U08, 323,[0:0], "On/Off", "Progressive" N2Oopt2_prog_time= bits, U08, 323,[1:1], "RPM-based", "Time-based" N2Oopt2_prog_freq= bits, U08, 323,[2:4], "INVALID", "78Hz", "39Hz", "26Hz", "19.5Hz", "15.6Hz", "13Hz", "11.1Hz" N2ORpm = scalar, U16, 324, "RPM", 1, 0, 1000, {rpmhigh}, 0 N2ORpmMax = scalar, U16, 326, "RPM", 1, 0, 1000, {rpmhigh}, 0 N2OTps = scalar, S16, 328, "%", 0.10000, 0.00000, 0.00, 100.00, 1; #if CELSIUS N2OClt = scalar, S16, 330, "°C", 0.05555, -320.000, -40.0, {clthighlim}, 1 ; * ( 2 bytes) #else N2OClt = scalar, S16, 330, "°F", 0.10000, 0.00000, -40.0, {clthighlim}, 1 #endif N2OAngle = scalar, S16, 332, "deg", 0.10000, 0.00000, 0, 50, 2 ; * ( 2 bytes) #if PW_4X N2OPWLo = scalar, S16, 334, "ms", 0.004, 0, -128, +128, 3 N2OPWHi = scalar, S16, 336, "ms", 0.004, 0, -128, +128, 3 #else N2OPWLo = scalar, S16, 334, "ms", 0.001, 0, -32, +32, 3 N2OPWHi = scalar, S16, 336, "ms", 0.001, 0, -32, +32, 3 #endif ;nitrous/launch N2Odel_launch = scalar, U08, 338, "s", 0.01, 0, 0, 2.55, 2 N2Odel_flat = scalar, U08, 339, "s", 0.01, 0, 0, 2.55, 2 N2Oholdon = scalar, U08, 340, "s", 0.01, 0, 0, 2.55, 2 ;nitrous stage 2 ; Nitrous System N2O2delay = scalar, U08, 341, "s", 0.01, 0, 0, 2.55,2 N2O2Rpm = scalar, U16, 342, "RPM", 1, 0, 1000, 25000, 0 N2O2RpmMax = scalar, U16, 344, "RPM", 1, 0, 1000, 25000, 0 N2O2Angle = scalar, S16, 346, "deg", 0.10000, 0.00000, 0, 50, 2 ; * ( 2 bytes) #if PW_4X N2O2PWLo = scalar, S16, 348, "ms", 0.004, 0, -128, +128, 3 N2O2PWHi = scalar, S16, 350, "ms", 0.004, 0, -128, +128, 3 #else N2O2PWLo = scalar, S16, 348, "ms", 0.001, 0, -32, +32, 3 N2O2PWHi = scalar, S16, 350, "ms", 0.001, 0, -32, +32, 3 #endif RotarySplitModeFD = bits, U08, 352, [0:0], "FC mode", "FD mode" RotarySplitModeNeg = bits, U08, 352, [1:1], "Not Allowed", "Allowed" dlyct = scalar, U08, 353, "", 1,0,0,255,0 dwelltime_trl = scalar, U08, 354, "ms", 0.10000, 0, 0.1, 25.5, 1 N2Oopt_pins = bits, U08, 355, [0:4], "INVALID", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "INVALID", "INVALID", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" RevLimRtdAng = scalar, S16, 356, "deg", 0.10000, 0.00000,-10, 25.5, 1 ; gap RevLimNormal2_hyst= scalar,U16, 360, "RPM", 1.00000, 0.00000, 0.00, 1000, 0 pwmidleset_inv = bits, U08, 362, [3:3], "Normal, 0%=off", "Inverted, 100%=off" trig_init = scalar, U08, 363, "", 1,0,0,255,0 ;pwmidle pwmidle_ms = scalar, U16, 364, "ms", 1, 0.00000, 0, 500, 0 pwmidle_close_delay = scalar, U08, 366, "s", 1, 0.00000, 0, 10, 0 pwmidle_open_duty = scalar, U08, 367, "%", 0.392, 0.00000, 0, 100, 1 pwmidle_open_steps = scalar, U08, 367, "steps", 1.00000, 0.00000, 0, 255, 0 ; same but steps pwmidle_closed_duty = scalar, U08, 368, "%", 0.392, 0.00000, 0, 100, 1 pwmidle_closed_steps = scalar, U08, 368, "steps", 1.00000, 0.00000, 0, 255, 0 ; same but steps pwmidle_pid_wait_timer = scalar, U08, 369, "s", 1, 0.00000, 0, 10, 0 pwmidle_freq_pin3 = bits, U08, 370, [0:3], "Off", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Boost", "Idle", "VVT", "Nitrous1", "Nitrous2", "Fidle", "Inj Bank 1", "Inj Bank 2" pwmidle_freq_koeo = bits, U08, 370, [7:7], "Off", "On" ac_idleup_min_rpm = scalar, U16, 371, "rpm", 1, 0, 0, {rpmhigh}, 0 pwmidle_tps_threshold = scalar, U16, 373, "%", 0.1, 0.00000, 0, 1000, 1 pwmidle_dp_adder = scalar, U08, 375, "%", 0.392, 0.00000, 0, 20, 1 pwmidle_dp_adder_steps = scalar, U08, 375, "steps", 1.00000, 0.00000, 0, 20, 0 ; same but steps pwmidle_rpmdot_threshold = scalar, U16, 376, "rpm/sec", 10.0, 0.00000, 0, 1000, 0 pwmidle_decelload_threshold=scalar,U16, 378, "%", 0.1, 0.00000, 0, 100, 1 pwmidle_Kp_new = scalar, U16, 380, "%", 0.1, 0.00000, 0, 200, 1 pwmidle_Ki_new = scalar, U16, 382, "%", 0.1, 0.00000, 0, 200, 1 pwmidle_Kd_new = scalar, U16, 384, "%", 0.1, 0.00000, 0, 200, 1 pwmidle_freq_scale = bits, U08, 386, [0:3], "1021Hz", "766Hz", "613Hz", "511Hz", "383Hz", "306Hz", "204Hz", "153Hz", "99Hz", "75Hz", "50Hz", "48Hz", "30Hz", "20Hz", "15Hz", "12Hz" pwmidle_freq_pin = bits, U08, 386, [4:6], "Boost", "Idle", "VVT", "Nitrous1", "Nitrous2", "Fidle", "Inj Bank 1", "Inj Bank 2" boost_ctl_settings_freq = bits, U08, 387, [0:2], "INVALID", "78Hz", "39Hz", "26Hz", "19.5Hz", "15.6Hz", "13Hz", "11.1Hz" boost_ctl_settings_on = bits, U08, 387, [3:3], "Off","On" boost_ctl_settings_cl = bits, U08, 387, [4:4], "Open-loop", "Closed-loop" boost_ctl_settings_invert_new= bits, U08, 387, [5:5], "Normal", "Inverted" boost_ctl_settings_initialvals=bits,U08,387, [6:6], "Off", "Use Initial Value Table" boost_ctl_settings_tunemode= bits,U08,387, [7:7], "Basic", "Advanced" boost_ctl_pins = bits, U08, 388, [0:5], "INVALID", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" boost_ctl_Kp = scalar, U08, 389, "%", 1, 0.00000, 0, 200, 0 boost_ctl_Ki = scalar, U08, 390, "%", 1, 0.00000, 0, 200, 0 boost_ctl_Kd = scalar, U08, 391, "%", 1, 0.00000, 0, 200, 0 boost_ctl_closeduty = scalar, U08, 392, "%", 1, 0.00000, 0, 100, 0 boost_ctl_openduty = scalar, U08, 393, "%", 1, 0.00000, 0, 100, 0 boost_ctl_ms = scalar, U16, 394, "ms", 1, 0.00000, 10, 500, 0 boost_ctl_pwm_scale = bits, U08, 396, [0:3], "1021Hz", "766Hz", "613Hz", "511Hz", "383Hz", "306Hz", "204Hz", "153Hz", "99Hz", "75Hz", "50Hz", "48Hz", "30Hz", "20Hz", "15Hz", "12Hz" boost_ctl_pwm = bits, U08, 396, [4:5], "INVALID", "Mid","Slow", "INVALID" NoiseFilterOpts = bits, U08, 397, [0:0], "Off", "On" NoiseFilterOpts1 = bits, U08, 397, [1:1], "Off", "On" NoiseFilterOpts2 = bits, U08, 397, [2:2], "Off", "On" NoiseFilterOpts3 = bits, U08, 397, [3:3], "Off", "On" ;pad x2 pwmidle_max_rpm_new = scalar, U16, 400, "", 1, 0.00000, 0, 4000, 0 pwmidle_targ_ramptime = scalar, U08, 402, "s", 1, 0.00000, 0, 10, 0 boost_ctl_pins_pwm = bits, U08, 403, [0:2], "Boost", "Idle", "VVT", "Nitrous1", "Nitrous2", "Fidle", "Inj Bank 1", "Inj Bank 2" ;accel wizard mini tables moved here to keep on one page taeBins = array , U08, 404, [ 4], "%", 1, 0.00000, 0.00, 255, 0 ; * ( 4 bytes) ; tpsen_table maeBins = array , U08, 408, [ 4], "%", 1, 0.00000, 0.00, 255, 0 ; * ( 4 bytes) ; mapen_table taeRates = array , S16, 412, [ 4], "%/s", 0.10000, 0.00000, 0.00, 3276.00, 1 ; * ( 8 bytes) tpsDot bins used for AE: x for TAE interpolation ; tpsdot_table maeRates = array , S16, 420, [ 4], "kPa/s", 1.00000, 0.00000, 0.00, 32767.0, 0 ; * ( 8 bytes) mapDot bins used for AE: x for MAE ; mapdot_table secondtrigopts = bits, U08, 428, [0:0], "Off", "On" secondtrigopts1 = bits, U08, 428, [1:1], "Off", "On" secondtrigopts2 = bits, U08, 428, [2:2], "Off", "On" secondtrigopts3 = bits, U08, 428, [3:3], "Off", "On" TC5_required_width = scalar, U16, 429, "uSec", 1.0, 0.00000, 0.00, 5000, 0 ; egoLimit = scalar, S16, 431, "%", 0.10000, 0.00000, 0.00, 50, 0 ; stoich = scalar, S16, 433, "AFR", 0.10000, 0.00000, 0.00, 25.5, 1 ; MAPOXMin = scalar, S16, 435, "%", 0.10000, 0.00000, -10, {loadhigh}, 2 ; * ( 2 bytes) IC2ISR_tmask = scalar, U08, 437, "ms", 0.1, 0.0, 0.0, 25.5, 1 ; * ( 1 byte ) IC2ISR_pmask = scalar, U08, 438, "%", 1.0, 0.0, 0.0, 90, 0 ; * ( 1 byte ) ;afrload and eaeload are part of extra_load_opts in firmware afrload = bits, U08, 439, [0:3], "Use primary load (Algorithm)", "MAP", "% baro", "TPS", "INVALID", "MAF", "ITB", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" eaeload = bits, U08, 439, [4:7], "Use primary load (Algorithm)", "MAP", "% baro", "TPS", "INVALID", "MAF", "ITB", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" ; airden_scaling = scalar, U08, 440, "%", 1, 0.00000, 0, 150.00, 0 fan_idleup_vss_hyst = scalar, U16, 441, { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, { msToPrefUnitsScale }, 0, 0, 200, 0 log_style_led = bits, U08, 443, [0:5], "Off", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "CANOUT1", "CANOUT2", "CANOUT3", "CANOUT4", "CANOUT5", "CANOUT6", "CANOUT7", "CANOUT8", "CANOUT9", "CANOUT10", "CANOUT11", "CANOUT12", "CANOUT13", "CANOUT14", "CANOUT15", "CANOUT16" log_style_ledspd = bits, U08, 443, [6:7], "Normal", "Slower", "Faster", "Fastest" primedelay = scalar, U08, 444, "s", 0.1, 0.0, 0.0, 3, 1 pwmidle_cl_opts_initvaluetable = bits, U08, 445, [0:0], "Use last value", "Use initial value table" pwmidle_cl_opts_initval_clt = bits, U08, 445, [1:1], "Use MAT", "Use CLT" pwmidle_cl_opts_display_pid = bits, U08, 445, [2:2], "Basic", "Advanced" idleveadv_to_pid_idleadv = bits, U08, 447, [0:0], "Use normal activation", "Use PID idle activation" idleveadv_to_pid_idleve = bits, U08, 447, [1:1], "Use normal activation", "Use PID idle activation" boost_ctl_sensitivity = scalar, S16, 448, "", 0.1, 0, 0, 500, 1 boost_ctl_sensitivity2 = scalar, S16, 450, "", 0.1, 0, 0, 500, 1 fuelcut_fuelon_upper_rpmdot = scalar, U16, 452, "rpmdot", 10, 0, 0, 10000, 0 fuelcut_fuelon_lower_rpmdot = scalar, U16, 454, "rpmdot", 10, 0, 0, 10000, 0 #if PW_4X staged_secondary_enrichment = scalar, U16, 456, "ms", 0.004, 0, 0, 10, 3 #else staged_secondary_enrichment = scalar, U16, 456, "ms", 0.001, 0, 0, 10, 3 #endif staged_primary_delay = scalar, U08, 458, "ign events", 1, 0, 0, 30, 0 idleadvance_on = bits, U08, 459, [0:0], "Off", "On" ; idleve_on = bits, U08, 459, [1:1], "Off", "On" idleve_vsson = bits, U08, 459, [2:3], "Off", "VSS1", "VSS2", "INVALID" idleadv_vsson = bits, U08, 459, [4:5], "Off", "VSS1", "VSS2", "INVALID" idle_special_ops_timing_assist = bits, U08, 459, [6:6], "Off", "On" idleadvance_tps = scalar, S16, 460, "%", 0.1, 0, 0, 100, 1 idleadvance_rpm = scalar, U16, 462, "rpm", 1, 0, 0, {rpmhigh}, 0 idleadvance_load = scalar, S16, 464, "%", 0.1, 0, 0, 100, 0 #if CELSIUS idleadvance_clt = scalar, S16, 466, "°C", 0.05555, -320, -40, {clthighlim}, 1 #else idleadvance_clt = scalar, S16, 466, "°F", 0.10000, 0.00000, -40, {clthighlim}, 1 #endif idleadvance_delay = scalar, U08, 468, "s", 1, 0, 0, 5, 0 idleadvance_curve = array, S16, 469, [ 4 ], "deg", 0.10000, 0.00000, -10.00, 90.00, 1 idleadvance_loads = array, S16, 477, [ 4 ], "%", 0.10000, 0.00000, 0, 100, 1 ;SD datalogging log_style2_but = bits, U08, 485, [0:4], "INVALID", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "INVALID", "INVALID", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" log_style_block = bits, U08, 486, [0:1], "64 byte", "64 byte + stream", "INVALID", "INVALID" log_style_gps = bits, U08, 486, [5:5], "Off", "On" log_style_on = bits, U08, 486, [6:7], "Disabled", "Insertion", "Button", "Trigger" ; old names log_style_on2 = bits, U08, 486, [6:7], "Disabled", "Always", "Button", "Trigger" ; new names log_style2_samp = bits, U08, 487, [3:4], "Timed", "every tooth", "every cycle", "INVALID" log_style2_clg = bits, U08, 487, [5:5], "Off", "On" log_style3_adc = bits, U08, 488, [0:2], "INT_MAP", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID" log_length = scalar, U08, 489, "mins", 1, 0, 1, 255, 0 log_int = scalar, U16, 490, "ms", 0.128,0,2.0,8388,1 log_rate = scalar, U16, 490, "", 1.0, { (1000/log_int) - (log_int/ 0.128) },0,1000,0 logFieldOffset = array , U16, 492, [ 64], "", 1.0000, 0.00000, 0.00, 65535, 0 ; * ( 64 words) logFieldLength = array , U08, 620, [ 64], "", 1.0000, 0.00000, 0.00, 255.00, 0 ; * ( 64 bytes) firea = scalar, U08, 684, "", 1,0,0,16,0 fireb = scalar, U08, 685, "", 1,0,0,16,0 firec = scalar, U08, 686, "", 1,0,0,16,0 fired = scalar, U08, 687, "", 1,0,0,16,0 firee = scalar, U08, 688, "", 1,0,0,16,0 firef = scalar, U08, 689, "", 1,0,0,16,0 fireg = scalar, U08, 690, "", 1,0,0,16,0 fireh = scalar, U08, 691, "", 1,0,0,16,0 firei = scalar, U08, 692, "", 1,0,0,16,0 firej = scalar, U08, 693, "", 1,0,0,16,0 firek = scalar, U08, 694, "", 1,0,0,16,0 firel = scalar, U08, 695, "", 1,0,0,16,0 firem = scalar, U08, 696, "", 1,0,0,16,0 firen = scalar, U08, 697, "", 1,0,0,16,0 fireo = scalar, U08, 698, "", 1,0,0,16,0 firep = scalar, U08, 699, "", 1,0,0,16,0 sequential = bits, U08, 700, [0:1], "Off", "Semi-sequential", "Fully Sequential", "INVALID" sequential_angle_spec = bits, U08, 700, [2:4], "INVALID", "End of squirt", "Middle of Squirt", "INVALID", "Beginning of squirt", "INVALID", "INVALID", "INVALID" sequential_trim_on_off = bits, U08, 700, [5:5], "Off", "On" ; sequential_bank_trim = bits, U08, 700, [6:6], "Off", "On" ; no longer used boost_launch_duty = scalar, U08, 701, "%", 1,0,0,100,0 boost_launch_target = scalar, U16, 702, "kPa", 1,0,0,{loadhigh},0 boost_feats_tsw = bits, U08, 704, [0:4], "Off", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "Blend Curve(6)","Gear-based", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" boost_feats_launch = bits, U08, 704, [5:5], "Off", "On" boost_feats_timed = bits, U08, 704, [6:6], "Off", "On" ;see lower for launch_var_on launch_3step_in = bits, U08, 705, [0:4], "Off", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "INVALID", "INVALID", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" launch_var_low = scalar, U16, 706, "rpm", 1,0,0,{rpmhigh},0 launch_var_up = scalar, U16, 708, "rpm", 1,0,0,{rpmhigh},0 vssout_scale = scalar, U32, 710, "", 1, 0, 0, 300000, 0 launch_sft_deg3 = scalar, S16, 714, "deg", 0.10000, 0.00000, -90.0, 180.00, 2 ; * ( 2 bytes) launch_hrd_lim3 = scalar, U16, 716, "RPM", 1.00000, 0.00000, 0.00, {rpmhigh}, 0 ; * ( 2 bytes) map_sample_duration = scalar, S16, 718, "deg", 0.10000, 0.00000, 0, 180, 1 ; * ( 2 bytes ) opentime_opt1_master = bits, U08, 720, [7:7], "Same", "Individual" opentime_opt1 = bits, U08, 720, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime_opt2 = bits, U08, 721, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime_opt3 = bits, U08, 722, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime_opt4 = bits, U08, 723, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime_opt5 = bits, U08, 724, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime_opt6 = bits, U08, 725, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime_opt7 = bits, U08, 726, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime_opt8 = bits, U08, 727, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime_opta = bits, U08, 728, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime_opta_pwm= bits, U08, 728, [4:4], "Off", "On" opentime_optb = bits, U08, 729, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime_optb_pwm= bits, U08, 729, [4:4], "Off", "On" opentime_optb_own= bits, U08, 729, [5:5], "Off", "On" opentime_opt11 = bits, U08, 730, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime_opt12 = bits, U08, 731, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime_opt13 = bits, U08, 732, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime_opt14 = bits, U08, 733, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime_opt15 = bits, U08, 734, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime_opt16 = bits, U08, 735, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" ; opentime_opt17 = bits, U08, 736, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" ; opentime_opt18 = bits, U08, 737, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw_opt1_master = bits, U08, 738, [7:7], "Off", "On" smallpw_opt1 = bits, U08, 738, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw_opt2 = bits, U08, 739, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw_opt3 = bits, U08, 740, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw_opt4 = bits, U08, 741, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw_opt5 = bits, U08, 742, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw_opt6 = bits, U08, 743, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw_opt7 = bits, U08, 744, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw_opt8 = bits, U08, 745, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw_opta = bits, U08, 746, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw_optb = bits, U08, 747, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw_opt11 = bits, U08, 748, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw_opt12 = bits, U08, 749, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw_opt13 = bits, U08, 750, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw_opt14 = bits, U08, 751, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw_opt15 = bits, U08, 752, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw_opt16 = bits, U08, 753, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" ; smallpw_opt17 = bits, U08, 754, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" ; smallpw_opt18 = bits, U08, 755, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" maxafr_opt1_on = bits, U08, 756, [0:0], "Off", "On" maxafr_opt1_load= bits,U08, 756, [1:2], "MAP", "TPS", "INVALID", "INVALID" maxafr_opt1_led = bits,U08, 757, [0:5], "Off", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "CANOUT1", "CANOUT2", "CANOUT3", "CANOUT4", "CANOUT5", "CANOUT6", "CANOUT7", "CANOUT8", "CANOUT9", "CANOUT10", "CANOUT11", "CANOUT12", "CANOUT13", "CANOUT14", "CANOUT15", "CANOUT16" maxafr_en_load = scalar, U16, 758, "%", 0.10000, 0, 0, {loadhigh}, 1 maxafr_en_rpm = scalar, U16, 760, "rpm", 1, 0, 0, {rpmhigh}, 0 maxafr_en_time = scalar, U16, 762, "s", 0.001, 0, 0, 5.000, 1 maxafr_spkcut_time=scalar, U16, 764, "s", 0.001, 0, 0, 5.000, 2 maxafr_ret_tps = scalar, S16, 766, "%", 0.10000, 0, 0, 110, 1 maxafr_ret_map = scalar, S16, 768, "%", 0.10000, 0, 0, {loadhigh}, 1 maxafr_ret_rpm = scalar, U16, 770, "rpm", 1, 0, 0, {rpmhigh}, 1 #if PW_4X launch_addfuel = scalar, S16, 772, "ms", 0.004, 0.0000, -128, +128, 3 #else launch_addfuel = scalar, S16, 772, "ms", 0.001, 0.0000, -32, +32, 3 #endif wheeldia1 = scalar, U16, 774, { bitStringValue( prefLengthUnits , prefLengthUnits ) }, { prefLengthUnits == 0 ? 0.001 : 0.03937 }, 0, { prefLengthUnits == 0 ? 0.3 : 12 }, { prefLengthUnits == 0 ? 2 : 79 }, 3;{ prefLengthUnits == 0 ? 3 : 1 } wheeldia2 = scalar, U16, 778, { bitStringValue( prefLengthUnits , prefLengthUnits ) }, { prefLengthUnits == 0 ? 0.001 : 0.03937 }, 0, { prefLengthUnits == 0 ? 0.3 : 12 }, { prefLengthUnits == 0 ? 2 : 79 }, 3;{ prefLengthUnits == 0 ? 3 : 1 } fdratio1 = scalar, U16, 776, ":1", 0.01, 0.00000, 0.40, 6.0, 2 ; * ( 2 bytes) ;not a gap vss1_pos = bits, U08, 780, [0:1], "Wheel", "Driveline", "Pulses per mile", "Pulses per km" vss2_pos = bits, U08, 780, [2:3], "Wheel", "Driveline", "Pulses per mile", "Pulses per km" launch_var_on = bits, U08, 781, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" flats_minvss = scalar, U16, 782, { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, { msToPrefUnitsScale }, 0.00000, 0.00, 200, 0 ; * ( 2 bytes) vss_opt1 = bits, U08, 784, [0:3], "INVALID", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "CAN VSS", "Use CAN PWMin" vss_opt2 = bits, U08, 784, [4:7], "INVALID", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "CAN VSS", "Use CAN PWMin" vss1_an = bits, U08, 785,[0:4], "INVALID", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" vss1_can_id = scalar, U08, 786, "", 1.00000, 0.00000, 0.00, 255, 0 ; tsw_pin_ob = bits, U08, 787, [0:4], "Off", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "INVALID", "INVALID", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" vss1_can_offset = scalar, U16, 788, "", 1.00000, 0.00000, 0.00, 65535, 0 ; vss2_can_offset = scalar, U16, 790, "", 1.00000, 0.00000, 0.00, 65535, 0 ; MapThreshXTD = scalar, U08, 792, "-kpa/sec", 1.00000, 0.00000, 0.00, 255.00, 0 ; MapThreshXTD2 = scalar, U08, 793, "-kpa/sec", 1.00000, 0.00000, 0.00, 255.00, 0 ; vss_opt0_1 = bits, U08, 794, [0:1], "Off", "Digital", "Analogue", "INVALID" vss_opt0_2 = bits, U08, 794, [2:3], "Off", "Digital", "Analogue", "INVALID" vss_opt0_3 = bits, U08, 794, [4:4], "Off", "On" vss_opt0_4 = bits, U08, 794, [6:6], "Off", "On" ; 1 gap ss_opt1 = bits, U08, 796, [0:3], "Off", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "INVALID", "Poll CAN" ss_opt1_spd = bits, U08, 796, [7:7], "Off", "On" vss2_an = bits, U08, 797,[0:4], "INVALID", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" ss1_pwmseq = scalar, U08, 798, "", 1.00000, 0.00000, 1, 4, 0 ss2_pwmseq = scalar, U08, 799, "", 1.00000, 0.00000, 1, 4, 0 gear_can_offset = scalar, U16, 800, "", 1.00000, 0.00000, 0.00, 65535, 0 ; mapsample_opt1 = bits, U08, 802, [0:1], "1", "2", "4", "INVALID" mapsample_opt2 = bits, U08, 802, [2:2], "Use timed min", "Use event average" map2port = bits, U08, 803, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" n2o1n_pins = bits, U08, 804, [0:5], "INVALID", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "CANOUT1", "CANOUT2", "CANOUT3", "CANOUT4", "CANOUT5", "CANOUT6", "CANOUT7", "CANOUT8", "CANOUT9", "CANOUT10", "CANOUT11", "CANOUT12", "CANOUT13", "CANOUT14", "CANOUT15", "CANOUT16" n2o1f_pins = bits, U08, 805, [0:5], "Same", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "CANOUT1", "CANOUT2", "CANOUT3", "CANOUT4", "CANOUT5", "CANOUT6", "CANOUT7", "CANOUT8", "CANOUT9", "CANOUT10", "CANOUT11", "CANOUT12", "CANOUT13", "CANOUT14", "CANOUT15", "CANOUT16" n2o2n_pins = bits, U08, 806, [0:5], "INVALID", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "CANOUT1", "CANOUT2", "CANOUT3", "CANOUT4", "CANOUT5", "CANOUT6", "CANOUT7", "CANOUT8", "CANOUT9", "CANOUT10", "CANOUT11", "CANOUT12", "CANOUT13", "CANOUT14", "CANOUT15", "CANOUT16" n2o2f_pins = bits, U08, 807, [0:5], "Same", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "CANOUT1", "CANOUT2", "CANOUT3", "CANOUT4", "CANOUT5", "CANOUT6", "CANOUT7", "CANOUT8", "CANOUT9", "CANOUT10", "CANOUT11", "CANOUT12", "CANOUT13", "CANOUT14", "CANOUT15", "CANOUT16" ; these an_max did use msToPrefUnitsScale, but that didn't change the values in real time vss1_an_max = scalar, U16, 808, { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, { prefSpeedUnits == 0 ? 0.22369 : 0.36 }, 0.00000, 0.00, 1000, 0 vss2_an_max = scalar, U16, 810, { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, { prefSpeedUnits == 0 ? 0.22369 : 0.36 }, 0.00000, 0.00, 1000, 0 tsw_pin_rf = bits, U08, 812, [0:4], "Off", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "INVALID", "INVALID", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" tsw_pin_afr = bits, U08, 813, [0:4], "Off", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "Blend curve(5)", "INVALID", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" tsw_pin_stoich = bits, U08, 814, [0:4], "Off", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "INVALID", "INVALID", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" boost_vss = bits, U08, 815, [0:1], "Off", "VSS1", "VSS2", "Gear" #if PW_4X ReqFuel_alt = scalar, U16, 816, "ms", 0.004, 0.00000, 0.00, 262.143, 2 #else ReqFuel_alt = scalar, U16, 816, "ms", 0.001, 0.00000, 0.00, 65.535, 2 #endif stoich_alt = scalar, S16, 818, "AFR", 0.10000, 0.00000, 0.00, 25.5, 1 water_pins_pump = bits, U08, 820, [0:5], "INVALID", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "CANOUT1", "CANOUT2", "CANOUT3", "CANOUT4", "CANOUT5", "CANOUT6", "CANOUT7", "CANOUT8", "CANOUT9", "CANOUT10", "CANOUT11", "CANOUT12", "CANOUT13", "CANOUT14", "CANOUT15", "CANOUT16" water_pins_valve = bits, U08, 821, [0:5], "Off", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" water_pins_in_shut = bits, U08, 822, [0:4], "Off", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "INVALID", "INVALID", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" water_freq_on = bits, U08, 823,[0:0], "Off", "On" water_freq = bits, U08, 823,[1:4], "INVALID", "INVALID", "250Hz", "225Hz", "200Hz", "175Hz", "150Hz", "125Hz", "100Hz", "78Hz", "39Hz", "26Hz", "19.5Hz", "15.6Hz", "13Hz", "11.1Hz" water_freq_type = bits, U08, 823,[5:6], "Off", "Fast", "Slow", "INVALID" boost_vss_tps = scalar, U16, 824, "%", 0.1, 0, 0, 100, 0 water_tps = scalar, S16, 826, "%", 0.1, 0, 0, 100, 0 water_rpm = scalar, U16, 828, "RPM", 1, 0, 0, {rpmhigh}, 0 water_map = scalar, S16, 830, "kPa", 0.1, 0, 0, {loadhigh}, 1 #if CELSIUS water_mat = scalar, S16, 832, "°C", 0.05555, -320, -40, 150.00, 1 #else water_mat = scalar, S16, 832, "°F", 0.10000, 0.00000, -40, 300, 1 #endif pwmidle_rpmdot_disablepid = scalar, S16, 834, "", 10.0000, 0.00000, 0, 1000, 0 boost_ctl_lowerlimit = scalar, S16, 836, "kPa",0.10000, 0.00000, 5, {loadhigh}, 1 enable_pollADC = bits, U08, 838, [0:0], "Disable", "Enable" ; enable_poll enable_pollPWM = bits, U08, 838, [1:2], "Disable", "16bit", "32bit", "INVALID" enable_pollports_digin = bits, U08,838, [3:3], "Disable", "Enable" enable_pollports_digout = bits,U08,838, [4:5], "Disable", "One", "Two", "INVALID" enable_pwmout = bits,U08,838, [6:6], "Disable", "Enable" enable_pwmout255 = bits,U08,838, [7:7], "Disable", "Enable" poll_table_rtc = scalar, U08, 839, "", 1.00000, 0.00000, 0, 15, 0 poll_tablePWM = scalar, U08, 840, "", 1.00000, 0.00000, 0, 15, 0 ; * ( 1 byte) poll_tableports = scalar, U08, 841, "", 1.00000, 0.00000, 0, 15, 0 ; * ( 1 byte) poll_offset_rtc = scalar, S16, 842, "bytes", 1.00000, 0.00000, 0, 4095, 0 poll_offsetPWM = scalar, S16, 844, "bytes", 1.00000, 0.00000, 0, 4095, 0 ; can_poll_digin_offset = scalar, S16, 846, "bytes", 1.00000, 0.00000, 0, 4095, 0 ; can_poll_digout_offset = scalar, S16, 848, "bytes", 1.00000, 0.00000, 0, 4095, 0 ; egt_num = bits, U08, 850, [0:4], "Off", "1", "2", "3", "4", "5", "6", "7", "8", "9", "10", "11", "12", "13", "14", "15", "16", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" accXport = bits, U08, 851, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" accYport = bits, U08, 852, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" accZport = bits, U08, 853, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" accXcal1 = scalar, S16, 854, "ADC", 1, 0, 0, 4095, 0 accXcal2 = scalar, S16, 856, "ADC", 1, 0, 0, 4095, 0 accYcal1 = scalar, S16, 858, "ADC", 1, 0, 0, 4095, 0 accYcal2 = scalar, S16, 860, "ADC", 1, 0, 0, 4095, 0 accZcal1 = scalar, S16, 862, "ADC", 1, 0, 0, 4095, 0 accZcal2 = scalar, S16, 864, "ADC", 1, 0, 0, 4095, 0 accxyzLF = scalar, U08, 866, "%", 1, 0, 10, 100, 0 egt1port = bits, U08, 867, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egt2port = bits, U08, 868, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egt3port = bits, U08, 869, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egt4port = bits, U08, 870, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egt5port = bits, U08, 871, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egt6port = bits, U08, 872, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egt7port = bits, U08, 873, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egt8port = bits, U08, 874, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egt9port = bits, U08, 875, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egt10port = bits, U08, 876, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egt11port = bits, U08, 877, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egt12port = bits, U08, 878, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egt13port = bits, U08, 879, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egt14port = bits, U08, 880, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egt15port = bits, U08, 881, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egt16port = bits, U08, 882, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "Analog In 3", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egt_conf_action = bits, U08, 883, [0:0], "Off", "On" egt_conf_shutdown = bits, U08, 883, [1:1], "Off", "On" egt_conf_bank = bits, U08, 883, [2:3], "INVALID", "Bank 1", "Bank 2", "Both" ;EGT calibration #if CELSIUS egtcal_temp0 = scalar, S16, 884, "°C", 0.05555, -320, -40, 1500, 0 egtcal_tempmax= scalar, S16, 886, "°C", 0.05555, -320, -40, 1500, 0 egt_warn = scalar, S16, 888, "°C", 0.05555, -320, -40, 1500, 0 egt_max = scalar, S16, 890, "°C", 0.05555, -320, -40, 1500, 0 #else egtcal_temp0 = scalar, S16, 884, "°F", 0.1, 0, -40, 2700, 0 egtcal_tempmax= scalar, S16, 886, "°F", 0.1, 0, -40, 2700, 0 egt_warn = scalar, S16, 888, "°F", 0.1, 0, -40, 2700, 0 egt_max = scalar, S16, 890, "°F", 0.1, 0, -40, 2700, 0 #endif egt_time = scalar, U16, 892, "s", 0.001, 0, 0, 10, 2 vss1_can_scale= scalar, U16, 894, "%", 0.1, 0, 0, 6553, 1 vss1_can_scale_pulse= scalar, U16, 894, "", 1, 0, 0, 65535, 0 vss2_can_scale= scalar, U16, 896, "%", 0.1, 0, 0, 6553, 1 vss2_can_scale_pulse= scalar, U16, 896, "", 1, 0, 0, 65535, 0 vss1_pwmseq = scalar, U08, 898, "", 1.00000, 0.00000, 1, 4, 0 vss2_pwmseq = scalar, U08, 899, "", 1.00000, 0.00000, 1, 4, 0 MAFOption = bits, U08, 900, [0:4], "INVALID", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "MAP (ADC0)", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" MAFOption_t = bits, U08, 900, [5:6], "Voltage", "Frequency", "Off", "INVALID" enginesize = scalar, U16, 901, "cc", 1.00000, 0.00000, 0, 65536, 0 vssout_opt = bits, U08, 903, [0:5], "Off", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" vssout_optunits= bits, U08, 903, [6:7], "Time", "Pulses per mile", "Pulses per km", "INVALID" ; moved vssout_scale = scalar, U16, 904, "", 1, 0, 0, 65535, 0 vss1_can_size = bits, U08, 906, [0:0], "8bit", "16bit" vss2_can_size = bits, U08, 906, [1:1], "8bit", "16bit" ;MAF Freq options in vss_can_size byte MAFOption_f = bits, U08, 906, [6:7], "PT4", "MS3X cam PT2", "JS10 PT5", "Datalog PT6" canpwm_clk = scalar, U08, 907, "MHz", 1,0,0,100,0 canpwm_pre = scalar, U08, 908, "", 1,0,0,255,0 canpwm_div = scalar, U08, 909, "", 1,0,0,255,0 vss1_can_table = scalar, U08, 910, "", 1,0,0,255,0 feature7_mafmat = bits, U08, 911, [0:0], "Off", "On" feature7_maftrim = bits, U08, 911, [1:1], "Off", "On" feature7_mafcalib= bits, U08, 911, [2:2], "Off", "On" feature7_aeevents= bits, U08, 911, [3:3], "Time", "Events" feature7_aetpswot= bits, U08, 911, [4:4], "Off", "On" feature7_batchcrank= bits,U08, 911, [5:5], "Off", "On" feature7_cranktaper= bits,U08, 911, [6:6], "Off", "On" feature7_crtpunits= bits, U08, 911, [7:7], "Time", "Events" vss1LF = scalar, U08, 912, "", 1,0,10,100,0 vss2LF = scalar, U08, 913, "", 1,0,10,100,0 ss1LF = scalar, U08, 914, "", 1,0,10,100,0 ss2LF = scalar, U08, 915, "", 1,0,10,100,0 #if PW_4X egt_addfuel = scalar, U16, 916, "ms", 0.004, 0.00000, 0.00, 262.143, 2 #else egt_addfuel = scalar, U16, 916, "ms", 0.001, 0.00000, 0.00, 65.535, 2 #endif launch_fcut_rpm= scalar, U16, 918, "RPM", 1, 0, 1000, 65000, 0 ;gear ratios gear1ratio = scalar, U16, 920, ":1", 0.01, 0.00000, 0.40, 5.0, 2 ; * ( 2 bytes) gear2ratio = scalar, U16, 922, ":1", 0.01, 0.00000, 0.40, 5.0, 2 ; * ( 2 bytes) gear3ratio = scalar, U16, 924, ":1", 0.01, 0.00000, 0.40, 5.0, 2 ; * ( 2 bytes) gear4ratio = scalar, U16, 926, ":1", 0.01, 0.00000, 0.40, 5.0, 2 ; * ( 2 bytes) gear5ratio = scalar, U16, 928, ":1", 0.01, 0.00000, 0.40, 5.0, 2 ; * ( 2 bytes) gear6ratio = scalar, U16, 930, ":1", 0.01, 0.00000, 0.40, 5.0, 2 ; * ( 2 bytes) gear_method = bits, U08, 932, [0:1], "Off", "VSS/RPM", "Analogue", "CAN Gear#" gear_port_an = bits, U08, 933, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" gear0v = scalar, U16, 934, "V", 0.01, 0.00000, 0.00, 5.0, 2 ; * ( 2 bytes) gear1v = scalar, U16, 936, "V", 0.01, 0.00000, 0.00, 5.0, 2 ; * ( 2 bytes) gear2v = scalar, U16, 938, "V", 0.01, 0.00000, 0.00, 5.0, 2 ; * ( 2 bytes) gear3v = scalar, U16, 940, "V", 0.01, 0.00000, 0.00, 5.0, 2 ; * ( 2 bytes) gear4v = scalar, U16, 942, "V", 0.01, 0.00000, 0.00, 5.0, 2 ; * ( 2 bytes) gear5v = scalar, U16, 944, "V", 0.01, 0.00000, 0.00, 5.0, 2 ; * ( 2 bytes) gear6v = scalar, U16, 946, "V", 0.01, 0.00000, 0.00, 5.0, 2 ; * ( 2 bytes) gear_no = scalar, U08, 948, "", 1, 0, 1, 6, 0 vssdotLF = scalar, U08, 949, "", 1,0,10,100,0 vssdot_int = scalar, U08, 950, "ms", 10, 0 , 10, 2000, 0 ac_idleup_io_in = bits, U08, 951, [0:4], "INVALID", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "INVALID", "INVALID", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" ac_idleup_settings = bits, U08, 951, [7:7], "Off", "On" ac_idleup_io_out = bits, U08, 952, [0:5], "Off", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "CANOUT1", "CANOUT2", "CANOUT3", "CANOUT4", "CANOUT5", "CANOUT6", "CANOUT7", "CANOUT8", "CANOUT9", "CANOUT10", "CANOUT11", "CANOUT12", "CANOUT13", "CANOUT14", "CANOUT15", "CANOUT16" ac_idleup_delay = scalar, U16, 953, "ms", 1.0000, 0.00000, 0.00, 1000, 0 ac_idleup_adder_duty = scalar, U08, 955, "%", 0.392, 0.00000, 0, 100, 1 ac_idleup_adder_steps = scalar, U08, 955, "steps", 1, 0, 0, 255, 0 fanctl_settings_on = bits, U08, 956, [7:7], "Off", "On" fanctl_settings_idleup = bits, U08, 956, [6:6], "No", "Yes" fanctl_settings_pin = bits, U08, 956, [0:5], "INVALID", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "CANOUT1", "CANOUT2", "CANOUT3", "CANOUT4", "CANOUT5", "CANOUT6", "CANOUT7", "CANOUT8", "CANOUT9", "CANOUT10", "CANOUT11", "CANOUT12", "CANOUT13", "CANOUT14", "CANOUT15", "CANOUT16" fanctl_idleup_delay = scalar, U16, 957, "ms", 1.0000, 0.00000, 0.00, 1000, 0 fanctl_idleup_adder_duty = scalar, U08, 959, "%", 0.392, 0.00000, 0, 100, 1 fanctl_idleup_adder_steps = scalar, U08, 959, "steps", 1.000, 0.00000, 0, 255, 0 #if CELSIUS fanctl_ontemp =scalar, S16, 960, "°C", 0.05555, -320.000,-40.00, 150.00, 1 fanctl_offtemp =scalar, S16, 962, "°C", 0.05555, -320.000,-40.00, 150.00, 1 #else fanctl_ontemp =scalar, S16, 960, "°F", 0.10000, 0.00000,-40.00, 300.00, 1 fanctl_offtemp =scalar, S16, 962, "°F", 0.10000, 0.00000,-40.00, 300.00, 1 #endif canadc_opt1 = bits, U08, 964, [0:0], "Off", "On" canadc_opt2 = bits, U08, 964, [1:1], "Off", "On" canadc_opt3 = bits, U08, 964, [2:2], "Off", "On" canadc_opt4 = bits, U08, 964, [3:3], "Off", "On" canadc_opt5 = bits, U08, 964, [4:4], "Off", "On" canadc_opt6 = bits, U08, 964, [5:5], "Off", "On" fanctl_opt2_engineoff = bits, U08, 965, [0:0], "No", "Yes" canadc_id1 = scalar, U08, 966, "", 1, 0, 0, 14, 0 canadc_id2 = scalar, U08, 967, "", 1, 0, 0, 14, 0 canadc_id3 = scalar, U08, 968, "", 1, 0, 0, 14, 0 canadc_id4 = scalar, U08, 969, "", 1, 0, 0, 14, 0 canadc_id5 = scalar, U08, 970, "", 1, 0, 0, 14, 0 canadc_id6 = scalar, U08, 971, "", 1, 0, 0, 14, 0 canadc_tab1 = scalar, U08, 972, "", 1, 0, 0, 31, 0 canadc_tab2 = scalar, U08, 973, "", 1, 0, 0, 31, 0 canadc_tab3 = scalar, U08, 974, "", 1, 0, 0, 31, 0 canadc_tab4 = scalar, U08, 975, "", 1, 0, 0, 31, 0 canadc_tab5 = scalar, U08, 976, "", 1, 0, 0, 31, 0 canadc_tab6 = scalar, U08, 977, "", 1, 0, 0, 31, 0 canadc_off1 = scalar, U16, 978, "", 1, 0, 0, 1023, 0 canadc_off2 = scalar, U16, 980, "", 1, 0, 0, 1023, 0 canadc_off3 = scalar, U16, 982, "", 1, 0, 0, 1023, 0 canadc_off4 = scalar, U16, 984, "", 1, 0, 0, 1023, 0 canadc_off5 = scalar, U16, 986, "", 1, 0, 0, 1023, 0 canadc_off6 = scalar, U16, 988, "", 1, 0, 0, 1023, 0 ac_idleup_cl_targetadder = scalar, S16, 990, "rpm", 1, 0, 0, 700, 0 fan_idleup_cl_targetadder = scalar, S16, 992, "rpm", 1, 0, 0, 700, 0 #if CELSIUS boost_ctl_clt_threshold = scalar, S16, 994, "°C", 0.05555, -320, -40, {clthighlim}, 1 #else boost_ctl_clt_threshold = scalar, S16, 994, "°F", 0.10000, 0.00000, -40, {clthighlim}, 1 #endif fan_ctl_settings_acfan = bits, U08, 996, [0:0], "Leave Fan off", "Turn fan on" #if LAMBDA ego_upper_bound = scalar, U08, 997, "Lambda", 0.006803, 0.00000, 0.0476, 1.7, 3 ego_lower_bound = scalar, U08, 998, "Lambda", 0.006803, 0.00000, 0.0476, 1.7, 3 #else ego_upper_bound = scalar, U08, 997, "AFR", 0.10000, 0.00000, 7, 25, 1 ego_lower_bound = scalar, U08, 998, "AFR", 0.10000, 0.00000, 7, 25, 1 #endif ss_opt2 = bits, U08, 999, [0:3], "Off", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "INVALID", "Poll CAN" ss_opt2_spd = bits, U08, 999, [7:7], "Off", "On" launch_maxvss = scalar, U16, 1000, { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, { msToPrefUnitsScale }, 0.00000, 0.00, 200, 0 ; * ( 2 bytes) maf_range = bits, U08, 1002, [0:1], "650g/s", "1300g/s", "1950g/s", "2600g/s" ac_delay_since_last_on = scalar, U08, 1003, "s", 1.00000, 0.00000, 0, 30, 0 reluctorteeth3 = scalar, U16, 1004, "", 0.01, 0,0,255,2 ; this is SS1 reluctorteeth4 = scalar, U16, 1006, "", 0.01, 0,0,255,2 ; this is SS2 boost_gear_switch = scalar, U08, 1008, "gear", 1, 0, 1, 7, 0 staged_extended_opts_use_v3 = bits, U08, 1009, [0:0], "Use MS3x (if possible)", "Use V3" staged_extended_opts_simult = bits, U08, 1009, [1:1], "Alternating (2 squirts)", "Simultaneous (1 squirt)" staged_extended_opts_pw1off = bits, U08, 1009, [2:2], "Off", "On" can_pwmout_id = scalar, U08, 1010, "", 1.00000, 0.00000, 0, 15, 0 ; * ( 1 byte) can_pwmout_tab = scalar, U08, 1011, "", 1.00000, 0.00000, 0, 15, 0 ; * ( 1 byte) can_pwmout_offset = scalar, S16, 1012, "bytes", 1.00000, 0.00000, 0, 4095, 0 ; idleve_tps = scalar, S16, 1014, "%", 0.10000, 0.00000, 0, 100, 1 idleve_rpm = scalar, U16, 1016, "rpm", 1.00000, 0.00000, 0, {rpmhigh}, 0 idleve_load = scalar, S16, 1018, "%", 0.10000, 0.00000, 0, {loadhigh}, 1 #if CELSIUS idleve_clt = scalar, S16, 1020, "°C", 0.05555, -320, -40, {clthighlim}, 1 #else idleve_clt = scalar, S16, 1020, "°F", 0.10000, 0.00000, -40, {clthighlim}, 1 #endif idleve_delay = scalar, U08, 1022, "s", 1.00000, 0.0000, 0, 10, 0 ac_idleup_cl_lockout_mapadder = scalar, U08, 1023, "%", 0.10000, 0.00000, 0, 25.5, 0 page = 2 pwm_testio = bits, U08, 0, [0:2], "INVALID", "78Hz", "39Hz", "26Hz", "19.5Hz", "15.6Hz", "13Hz", "11.1Hz" duty_testio = scalar, U08, 1, "%", 1, 0, 0, 100, 1 testop_0 = scalar, U08, 2, "", 1,0,0,255,0 testop_coil = bits, U08, 2, [0:1], "Off", "One", "Sequence", "INVALID" testop_fp = bits, U08, 2, [4:4], "Off", "On" testop_inj = bits, U08, 2, [5:6], "Off", "One", "Sequence", "All" testop_pwm = bits, U08, 2, [7:7], "Standard", "As below" testdwell = scalar, U08, 3, "ms", 0.1,0,0,25.5,1 testint = scalar, U16, 4, "ms", 0.128,0,0,8388,1 ;this depend on single coil or seq etc. testrpm = scalar, U16, 4, "RPM", 1.0, { (120000/testint) - (testint/ 0.128) },0,937500,0 #if PW_4X testpw = scalar, U16, 6, "ms", 0.004, 0.00000, 0, 262.143, 3 #else testpw = scalar, U16, 6, "ms", 0.001, 0.00000, 0, 65.535, 3 #endif testinjcnt = scalar, U16, 8, "", 1,0,0,65535,0 ;gap testinjPwmT = scalar, U08, 11, "ms", 0.12800, 0.12800, 0.00, 32.64, 1 testinjPwmPd = scalar, U08, 12, "us", 1.00000, 0.00000, 40.00, 100.00, 0 testinjPwmP = scalar, U08, 13, "%", 1.00000, 0.00000, 0.00, 100.00, 0 testsel_inj = bits, U08, 14, [0:3], "InjA", "InjB", "InjC", "InjD", "InjE", "InjF", "InjG", "InjH", "Inj1/I", "Inj2/J", "InjK", "InjL", "INVALID", "INVALID", "INVALID", "INVALID" testsel_coil = bits, U08, 14, [4:7], "CoilA", "CoilB", "CoilC", "CoilD", "CoilE", "CoilF", "CoilG", "CoilH", "CoilI", "CoilJ", "CoilK", "CoilL", "CoilM", "CoilN", "INVALID", "INVALID" dbgtooth = scalar, U08, 15, "tooth", 1,0,0,255,0 iacpostest = scalar, U16, 16, "steps", 1,0,0,65535,0 iachometest = scalar, U16, 18, "steps", 1,0,0,65535,0 iactest_0 = scalar, U08, 20, "", 1,0,0,255,0 flashlock = bits, U08, 21, [0:0], "Locked", "Unlocked" ; tables 0-3 boost_ctl_settings_on2 = bits, U08, 22, [3:3], "Off","On" boost_ctl_settings_cl2 = bits, U08, 22, [4:4], "Open-loop", "Closed-loop" boost_ctl_settings_tunemode2 = bits,U08, 22, [7:7], "Basic", "Advanced" boost_ctl_pins2 = bits, U08, 23, [0:5], "INVALID", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" boost_ctl_Kp2 = scalar, U08, 24, "%", 1, 0.00000, 0, 200, 0 boost_ctl_Ki2 = scalar, U08, 25, "%", 1, 0.00000, 0, 200, 0 boost_ctl_Kd2 = scalar, U08, 26, "%", 1, 0.00000, 0, 200, 0 boost_ctl_closeduty2 = scalar, U08, 27, "%", 1, 0.00000, 0, 100, 0 boost_ctl_openduty2 = scalar, U08, 28, "%", 1, 0.00000, 0, 100, 0 boost_ctl_pins_pwm2 = bits, U08, 29, [0:2], "Boost", "Idle", "VVT", "Nitrous1", "Nitrous2", "Fidle", "Inj Bank 1", "Inj Bank 2" boost_ctl_lowerlimit2 = scalar, S16, 30, "kPa",0.10000, 0.00000, 5, {loadhigh}, 1 boost_ctl_sensor2 = bits, U08, 32, [0:3], "Sensor 1", "Sensor 2","Sensor 3","Sensor 4","Sensor 5","Sensor 6","Sensor 7","Sensor 8","Sensor 9","Sensor 10","Sensor 11","Sensor 12","Sensor 13","Sensor 14","Sensor 15","Sensor 16" vss_opt3 = bits, U08, 33, [0:3], "INVALID", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "CAN VSS", "Use CAN PWMin" vss_opt4 = bits, U08, 33, [4:7], "INVALID", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "CAN VSS", "Use CAN PWMin" vss3_an = bits, U08, 34,[0:4], "INVALID", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" vss4_an = bits, U08, 35,[0:4], "INVALID", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" vss3_pwmseq = scalar, U08, 36, "", 1.00000, 0.00000, 1, 4, 0 vss4_pwmseq = scalar, U08, 37, "", 1.00000, 0.00000, 1, 4, 0 u08_debug38 = scalar, U08, 38, "", 1, 0.00000, 0, +255, 0 u08_debug38_0 = bits, U08, 38, [0:0], "Normal", "Loopback" u08_debug38_1 = bits, U08, 38, [1:1], "Off", "On" ; pad gap egoport1 = bits, U08, 40, [0:4], "Normal EGO", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "CAN EGO", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egoport2 = bits, U08, 41, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "CAN EGO", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egoport3 = bits, U08, 42, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "CAN EGO", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egoport4 = bits, U08, 43, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "CAN EGO", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egoport5 = bits, U08, 44, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "CAN EGO", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egoport6 = bits, U08, 45, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "CAN EGO", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egoport7 = bits, U08, 46, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "CAN EGO", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egoport8 = bits, U08, 47, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "CAN EGO", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egoport9 = bits, U08, 48, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "CAN EGO", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egoport10 = bits, U08, 49, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "CAN EGO", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egoport11 = bits, U08, 50, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "CAN EGO", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egoport12 = bits, U08, 51, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "CAN EGO", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egoport13 = bits, U08, 52, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "CAN EGO", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egoport14 = bits, U08, 53, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "CAN EGO", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egoport15 = bits, U08, 54, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "CAN EGO", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egoport16 = bits, U08, 55, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "CAN EGO", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" egomap1 = bits, U08, 56, [0:3], "EGO1", "EGO2", "EGO3", "EGO4", "EGO5", "EGO6", "EGO7", "EGO8", "EGO9", "EGO10", "EGO11", "EGO12", "EGO13", "EGO14", "EGO15", "EGO16" egomap2 = bits, U08, 57, [0:3], "EGO1", "EGO2", "EGO3", "EGO4", "EGO5", "EGO6", "EGO7", "EGO8", "EGO9", "EGO10", "EGO11", "EGO12", "EGO13", "EGO14", "EGO15", "EGO16" egomap3 = bits, U08, 58, [0:3], "EGO1", "EGO2", "EGO3", "EGO4", "EGO5", "EGO6", "EGO7", "EGO8", "EGO9", "EGO10", "EGO11", "EGO12", "EGO13", "EGO14", "EGO15", "EGO16" egomap4 = bits, U08, 59, [0:3], "EGO1", "EGO2", "EGO3", "EGO4", "EGO5", "EGO6", "EGO7", "EGO8", "EGO9", "EGO10", "EGO11", "EGO12", "EGO13", "EGO14", "EGO15", "EGO16" egomap5 = bits, U08, 60, [0:3], "EGO1", "EGO2", "EGO3", "EGO4", "EGO5", "EGO6", "EGO7", "EGO8", "EGO9", "EGO10", "EGO11", "EGO12", "EGO13", "EGO14", "EGO15", "EGO16" egomap6 = bits, U08, 61, [0:3], "EGO1", "EGO2", "EGO3", "EGO4", "EGO5", "EGO6", "EGO7", "EGO8", "EGO9", "EGO10", "EGO11", "EGO12", "EGO13", "EGO14", "EGO15", "EGO16" egomap7 = bits, U08, 62, [0:3], "EGO1", "EGO2", "EGO3", "EGO4", "EGO5", "EGO6", "EGO7", "EGO8", "EGO9", "EGO10", "EGO11", "EGO12", "EGO13", "EGO14", "EGO15", "EGO16" egomap8 = bits, U08, 63, [0:3], "EGO1", "EGO2", "EGO3", "EGO4", "EGO5", "EGO6", "EGO7", "EGO8", "EGO9", "EGO10", "EGO11", "EGO12", "EGO13", "EGO14", "EGO15", "EGO16" egomap9 = bits, U08, 64, [0:3], "EGO1", "EGO2", "EGO3", "EGO4", "EGO5", "EGO6", "EGO7", "EGO8", "EGO9", "EGO10", "EGO11", "EGO12", "EGO13", "EGO14", "EGO15", "EGO16" egomap10 = bits, U08, 65, [0:3], "EGO1", "EGO2", "EGO3", "EGO4", "EGO5", "EGO6", "EGO7", "EGO8", "EGO9", "EGO10", "EGO11", "EGO12", "EGO13", "EGO14", "EGO15", "EGO16" egomap11 = bits, U08, 66, [0:3], "EGO1", "EGO2", "EGO3", "EGO4", "EGO5", "EGO6", "EGO7", "EGO8", "EGO9", "EGO10", "EGO11", "EGO12", "EGO13", "EGO14", "EGO15", "EGO16" egomap12 = bits, U08, 67, [0:3], "EGO1", "EGO2", "EGO3", "EGO4", "EGO5", "EGO6", "EGO7", "EGO8", "EGO9", "EGO10", "EGO11", "EGO12", "EGO13", "EGO14", "EGO15", "EGO16" egomap13 = bits, U08, 68, [0:3], "EGO1", "EGO2", "EGO3", "EGO4", "EGO5", "EGO6", "EGO7", "EGO8", "EGO9", "EGO10", "EGO11", "EGO12", "EGO13", "EGO14", "EGO15", "EGO16" egomap14 = bits, U08, 69, [0:3], "EGO1", "EGO2", "EGO3", "EGO4", "EGO5", "EGO6", "EGO7", "EGO8", "EGO9", "EGO10", "EGO11", "EGO12", "EGO13", "EGO14", "EGO15", "EGO16" egomap15 = bits, U08, 70, [0:3], "EGO1", "EGO2", "EGO3", "EGO4", "EGO5", "EGO6", "EGO7", "EGO8", "EGO9", "EGO10", "EGO11", "EGO12", "EGO13", "EGO14", "EGO15", "EGO16" egomap16 = bits, U08, 71, [0:3], "EGO1", "EGO2", "EGO3", "EGO4", "EGO5", "EGO6", "EGO7", "EGO8", "EGO9", "EGO10", "EGO11", "EGO12", "EGO13", "EGO14", "EGO15", "EGO16" ;egomap?t is not presently implemented in the code egomap1t = bits, U08, 56, [4:4], "1", "2" egomap2t = bits, U08, 57, [4:4], "1", "2" egomap3t = bits, U08, 58, [4:4], "1", "2" egomap4t = bits, U08, 59, [4:4], "1", "2" egomap5t = bits, U08, 60, [4:4], "1", "2" egomap6t = bits, U08, 61, [4:4], "1", "2" egomap7t = bits, U08, 62, [4:4], "1", "2" egomap8t = bits, U08, 63, [4:4], "1", "2" egomap9t = bits, U08, 64, [4:4], "1", "2" egomap10t = bits, U08, 65, [4:4], "1", "2" egomap11t = bits, U08, 66, [4:4], "1", "2" egomap12t = bits, U08, 67, [4:4], "1", "2" egomap13t = bits, U08, 68, [4:4], "1", "2" egomap14t = bits, U08, 69, [4:4], "1", "2" egomap15t = bits, U08, 70, [4:4], "1", "2" egomap16t = bits, U08, 71, [4:4], "1", "2" tc_opt_on = bits, U08, 72, [0:0], "Off", "On" tc_opt_method = bits, U08, 72, [1:2], "Perfect Run", "VSS %slip", "Perfect Run RPM", "Switch input" tc_opt_slipcurve=bits,U08, 72, [4:4], "Fixed value", "Adjustable" tc_opt_n2o = bits, U08, 72, [5:5], "On/Off", "INVALID" tc_opt_bank = bits, U08, 72, [6:7], "INVALID", "Bank 1", "Bank 2", "Both" tc_slipthresh = scalar, U08, 73, "%", 1, 0.00000, 0, 100, 0 tc_minvss = scalar, U16, 74, { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, { msToPrefUnitsScale }, 0.00000, 0, 200, 1 tc_maxvss = scalar, U16, 76, { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, { msToPrefUnitsScale }, 0.00000, 0, 200, 1 tc_mintps = scalar, S16, 78, "%", 0.10000, 0.00000, 0, 100, 1 tc_enin = bits, U08, 80, [0:4], "Off", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "INVALID", "INVALID", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" knock_bpass = bits, U08, 81, [0:5], "1.22", "1.26", "1.31", "1.35", "1.40", "1.45", "1.51", "1.57", "1.63", "1.71", "1.78", "1.87", "1.96", "2.07", "2.18", "2.31", "2.46", "2.54", "2.62", "2.71", "2.81", "2.92", "3.03", "3.15", "3.28", "3.43", "3.59", "3.76", "3.95", "4.16", "4.39", "4.66", "4.95", "5.12", "5.29", "5.48", "5.68", "5.90", "6.12", "6.37", "6.64", "6.94", "7.27", "7.63", "8.02", "8.46", "8.95", "9.50", "10.12", "10.46", "10.83", "11.22", "11.65", "12.10", "12.60", "13.14", "13.72", "14.36", "15.07", "15.84", "16.71", "17.67", "18.76", "19.98" knock_conf_num = bits, U08, 82, [0:0], "1", "2" knock_conf_launch = bits, U08, 82, [6:6], "Off", "On" knock_conf_percyl = bits, U08, 82, [7:7], "Off", "On" knock_int = bits, U08, 83, [0:4], "40", "45", "50", "55", "60", "65", "70", "75", "80", "90", "100", "110", "120", "130", "140", "150", "160", "180", "200", "220", "240", "260", "280", "300", "320", "360", "400", "440", "480", "520", "560", "600" ff_tpw0 = scalar, U08, 84, "ms", 0.05, 0, 0, 12.7, 2 ff_tpw1 = scalar, U08, 85, "ms", 0.05, 0, 0, 12.7, 2 #if CELSIUS ff_temp0 = scalar, S16, 86, "°C", 0.05555, -320, -40, 150.00, 1 ff_temp1 = scalar, S16, 88, "°C", 0.05555, -320, -40, 150.00, 1 #else ff_temp0 = scalar, S16, 86, "°F", 0.10000, 0.00000, -40, 300, 1 ff_temp1 = scalar, S16, 88, "°F", 0.10000, 0.00000, -40, 300, 1 #endif fueltemp1 = bits, U08, 90, [0:4], "Off", "Flex fuel", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Sensor 1", "Sensor 2","Sensor 3","Sensor 4","Sensor 5","Sensor 6","Sensor 7","Sensor 8","Sensor 9","Sensor 10","Sensor 11","Sensor 12","Sensor 13","Sensor 14","Sensor 15","Sensor 16" fueltemp1_corr = bits, U08, 90, [7:7], "Off", "On" tc_knob = bits, U08, 91, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" maf_freq0 = scalar, U16, 92, "Hz", 0.25, 0.00000, 0, 16383,1 maf_freq1 = scalar, U16, 94, "Hz", 0.25, 0.00000, 0, 16383,1 map_freq0 = scalar, U16, 96, "Hz", 0.2, 0.00000, 0, 13107,1 map_freq1 = scalar, U16, 98, "Hz", 0.2, 0.00000, 0, 13107,1 knock_gain01 = bits, U08, 100, [0:5], "2.000", "1.882", "1.778", "1.684", "1.600", "1.523", "1.455", "1.391", "1.333", "1.280", "1.231", "1.185", "1.143", "1.063", "1.000", "0.944", "0.895", "0.85", "0.81", "0.773", "0.739", "0.708", "0.680", "0.654", "0.630", "0.607", "0.586", "0.567", "0.548", "0.500", "0.471", "0.444", "0.421", "0.400", "0.381", "0.364", "0.348", "0.333", "0.320", "0.308", "0.296", "0.286", "0.276", "0.267", "0.258", "0.250", "0.236", "0.222", "0.211", "0.200", "0.190", "0.182", "0.174", "0.167", "0.160", "0.154", "0.148", "0.143", "0.138", "0.133", "0.129", "0.125", "0.118", "0.111" knock_gain02 = bits, U08, 101, [0:5], "2.000", "1.882", "1.778", "1.684", "1.600", "1.523", "1.455", "1.391", "1.333", "1.280", "1.231", "1.185", "1.143", "1.063", "1.000", "0.944", "0.895", "0.85", "0.81", "0.773", "0.739", "0.708", "0.680", "0.654", "0.630", "0.607", "0.586", "0.567", "0.548", "0.500", "0.471", "0.444", "0.421", "0.400", "0.381", "0.364", "0.348", "0.333", "0.320", "0.308", "0.296", "0.286", "0.276", "0.267", "0.258", "0.250", "0.236", "0.222", "0.211", "0.200", "0.190", "0.182", "0.174", "0.167", "0.160", "0.154", "0.148", "0.143", "0.138", "0.133", "0.129", "0.125", "0.118", "0.111" knock_gain03 = bits, U08, 102, [0:5], "2.000", "1.882", "1.778", "1.684", "1.600", "1.523", "1.455", "1.391", "1.333", "1.280", "1.231", "1.185", "1.143", "1.063", "1.000", "0.944", "0.895", "0.85", "0.81", "0.773", "0.739", "0.708", "0.680", "0.654", "0.630", "0.607", "0.586", "0.567", "0.548", "0.500", "0.471", "0.444", "0.421", "0.400", "0.381", "0.364", "0.348", "0.333", "0.320", "0.308", "0.296", "0.286", "0.276", "0.267", "0.258", "0.250", "0.236", "0.222", "0.211", "0.200", "0.190", "0.182", "0.174", "0.167", "0.160", "0.154", "0.148", "0.143", "0.138", "0.133", "0.129", "0.125", "0.118", "0.111" knock_gain04 = bits, U08, 103, [0:5], "2.000", "1.882", "1.778", "1.684", "1.600", "1.523", "1.455", "1.391", "1.333", "1.280", "1.231", "1.185", "1.143", "1.063", "1.000", "0.944", "0.895", "0.85", "0.81", "0.773", "0.739", "0.708", "0.680", "0.654", "0.630", "0.607", "0.586", "0.567", "0.548", "0.500", "0.471", "0.444", "0.421", "0.400", "0.381", "0.364", "0.348", "0.333", "0.320", "0.308", "0.296", "0.286", "0.276", "0.267", "0.258", "0.250", "0.236", "0.222", "0.211", "0.200", "0.190", "0.182", "0.174", "0.167", "0.160", "0.154", "0.148", "0.143", "0.138", "0.133", "0.129", "0.125", "0.118", "0.111" knock_gain05 = bits, U08, 104, [0:5], "2.000", "1.882", "1.778", "1.684", "1.600", "1.523", "1.455", "1.391", "1.333", "1.280", "1.231", "1.185", "1.143", "1.063", "1.000", "0.944", "0.895", "0.85", "0.81", "0.773", "0.739", "0.708", "0.680", "0.654", "0.630", "0.607", "0.586", "0.567", "0.548", "0.500", "0.471", "0.444", "0.421", "0.400", "0.381", "0.364", "0.348", "0.333", "0.320", "0.308", "0.296", "0.286", "0.276", "0.267", "0.258", "0.250", "0.236", "0.222", "0.211", "0.200", "0.190", "0.182", "0.174", "0.167", "0.160", "0.154", "0.148", "0.143", "0.138", "0.133", "0.129", "0.125", "0.118", "0.111" knock_gain06 = bits, U08, 105, [0:5], "2.000", "1.882", "1.778", "1.684", "1.600", "1.523", "1.455", "1.391", "1.333", "1.280", "1.231", "1.185", "1.143", "1.063", "1.000", "0.944", "0.895", "0.85", "0.81", "0.773", "0.739", "0.708", "0.680", "0.654", "0.630", "0.607", "0.586", "0.567", "0.548", "0.500", "0.471", "0.444", "0.421", "0.400", "0.381", "0.364", "0.348", "0.333", "0.320", "0.308", "0.296", "0.286", "0.276", "0.267", "0.258", "0.250", "0.236", "0.222", "0.211", "0.200", "0.190", "0.182", "0.174", "0.167", "0.160", "0.154", "0.148", "0.143", "0.138", "0.133", "0.129", "0.125", "0.118", "0.111" knock_gain07 = bits, U08, 106, [0:5], "2.000", "1.882", "1.778", "1.684", "1.600", "1.523", "1.455", "1.391", "1.333", "1.280", "1.231", "1.185", "1.143", "1.063", "1.000", "0.944", "0.895", "0.85", "0.81", "0.773", "0.739", "0.708", "0.680", "0.654", "0.630", "0.607", "0.586", "0.567", "0.548", "0.500", "0.471", "0.444", "0.421", "0.400", "0.381", "0.364", "0.348", "0.333", "0.320", "0.308", "0.296", "0.286", "0.276", "0.267", "0.258", "0.250", "0.236", "0.222", "0.211", "0.200", "0.190", "0.182", "0.174", "0.167", "0.160", "0.154", "0.148", "0.143", "0.138", "0.133", "0.129", "0.125", "0.118", "0.111" knock_gain08 = bits, U08, 107, [0:5], "2.000", "1.882", "1.778", "1.684", "1.600", "1.523", "1.455", "1.391", "1.333", "1.280", "1.231", "1.185", "1.143", "1.063", "1.000", "0.944", "0.895", "0.85", "0.81", "0.773", "0.739", "0.708", "0.680", "0.654", "0.630", "0.607", "0.586", "0.567", "0.548", "0.500", "0.471", "0.444", "0.421", "0.400", "0.381", "0.364", "0.348", "0.333", "0.320", "0.308", "0.296", "0.286", "0.276", "0.267", "0.258", "0.250", "0.236", "0.222", "0.211", "0.200", "0.190", "0.182", "0.174", "0.167", "0.160", "0.154", "0.148", "0.143", "0.138", "0.133", "0.129", "0.125", "0.118", "0.111" knock_gain09 = bits, U08, 108, [0:5], "2.000", "1.882", "1.778", "1.684", "1.600", "1.523", "1.455", "1.391", "1.333", "1.280", "1.231", "1.185", "1.143", "1.063", "1.000", "0.944", "0.895", "0.85", "0.81", "0.773", "0.739", "0.708", "0.680", "0.654", "0.630", "0.607", "0.586", "0.567", "0.548", "0.500", "0.471", "0.444", "0.421", "0.400", "0.381", "0.364", "0.348", "0.333", "0.320", "0.308", "0.296", "0.286", "0.276", "0.267", "0.258", "0.250", "0.236", "0.222", "0.211", "0.200", "0.190", "0.182", "0.174", "0.167", "0.160", "0.154", "0.148", "0.143", "0.138", "0.133", "0.129", "0.125", "0.118", "0.111" knock_gain10 = bits, U08, 109, [0:5], "2.000", "1.882", "1.778", "1.684", "1.600", "1.523", "1.455", "1.391", "1.333", "1.280", "1.231", "1.185", "1.143", "1.063", "1.000", "0.944", "0.895", "0.85", "0.81", "0.773", "0.739", "0.708", "0.680", "0.654", "0.630", "0.607", "0.586", "0.567", "0.548", "0.500", "0.471", "0.444", "0.421", "0.400", "0.381", "0.364", "0.348", "0.333", "0.320", "0.308", "0.296", "0.286", "0.276", "0.267", "0.258", "0.250", "0.236", "0.222", "0.211", "0.200", "0.190", "0.182", "0.174", "0.167", "0.160", "0.154", "0.148", "0.143", "0.138", "0.133", "0.129", "0.125", "0.118", "0.111" knock_gain11 = bits, U08, 110, [0:5], "2.000", "1.882", "1.778", "1.684", "1.600", "1.523", "1.455", "1.391", "1.333", "1.280", "1.231", "1.185", "1.143", "1.063", "1.000", "0.944", "0.895", "0.85", "0.81", "0.773", "0.739", "0.708", "0.680", "0.654", "0.630", "0.607", "0.586", "0.567", "0.548", "0.500", "0.471", "0.444", "0.421", "0.400", "0.381", "0.364", "0.348", "0.333", "0.320", "0.308", "0.296", "0.286", "0.276", "0.267", "0.258", "0.250", "0.236", "0.222", "0.211", "0.200", "0.190", "0.182", "0.174", "0.167", "0.160", "0.154", "0.148", "0.143", "0.138", "0.133", "0.129", "0.125", "0.118", "0.111" knock_gain12 = bits, U08, 111, [0:5], "2.000", "1.882", "1.778", "1.684", "1.600", "1.523", "1.455", "1.391", "1.333", "1.280", "1.231", "1.185", "1.143", "1.063", "1.000", "0.944", "0.895", "0.85", "0.81", "0.773", "0.739", "0.708", "0.680", "0.654", "0.630", "0.607", "0.586", "0.567", "0.548", "0.500", "0.471", "0.444", "0.421", "0.400", "0.381", "0.364", "0.348", "0.333", "0.320", "0.308", "0.296", "0.286", "0.276", "0.267", "0.258", "0.250", "0.236", "0.222", "0.211", "0.200", "0.190", "0.182", "0.174", "0.167", "0.160", "0.154", "0.148", "0.143", "0.138", "0.133", "0.129", "0.125", "0.118", "0.111" knock_gain13 = bits, U08, 112, [0:5], "2.000", "1.882", "1.778", "1.684", "1.600", "1.523", "1.455", "1.391", "1.333", "1.280", "1.231", "1.185", "1.143", "1.063", "1.000", "0.944", "0.895", "0.85", "0.81", "0.773", "0.739", "0.708", "0.680", "0.654", "0.630", "0.607", "0.586", "0.567", "0.548", "0.500", "0.471", "0.444", "0.421", "0.400", "0.381", "0.364", "0.348", "0.333", "0.320", "0.308", "0.296", "0.286", "0.276", "0.267", "0.258", "0.250", "0.236", "0.222", "0.211", "0.200", "0.190", "0.182", "0.174", "0.167", "0.160", "0.154", "0.148", "0.143", "0.138", "0.133", "0.129", "0.125", "0.118", "0.111" knock_gain14 = bits, U08, 113, [0:5], "2.000", "1.882", "1.778", "1.684", "1.600", "1.523", "1.455", "1.391", "1.333", "1.280", "1.231", "1.185", "1.143", "1.063", "1.000", "0.944", "0.895", "0.85", "0.81", "0.773", "0.739", "0.708", "0.680", "0.654", "0.630", "0.607", "0.586", "0.567", "0.548", "0.500", "0.471", "0.444", "0.421", "0.400", "0.381", "0.364", "0.348", "0.333", "0.320", "0.308", "0.296", "0.286", "0.276", "0.267", "0.258", "0.250", "0.236", "0.222", "0.211", "0.200", "0.190", "0.182", "0.174", "0.167", "0.160", "0.154", "0.148", "0.143", "0.138", "0.133", "0.129", "0.125", "0.118", "0.111" knock_gain15 = bits, U08, 114, [0:5], "2.000", "1.882", "1.778", "1.684", "1.600", "1.523", "1.455", "1.391", "1.333", "1.280", "1.231", "1.185", "1.143", "1.063", "1.000", "0.944", "0.895", "0.85", "0.81", "0.773", "0.739", "0.708", "0.680", "0.654", "0.630", "0.607", "0.586", "0.567", "0.548", "0.500", "0.471", "0.444", "0.421", "0.400", "0.381", "0.364", "0.348", "0.333", "0.320", "0.308", "0.296", "0.286", "0.276", "0.267", "0.258", "0.250", "0.236", "0.222", "0.211", "0.200", "0.190", "0.182", "0.174", "0.167", "0.160", "0.154", "0.148", "0.143", "0.138", "0.133", "0.129", "0.125", "0.118", "0.111" knock_gain16 = bits, U08, 115, [0:5], "2.000", "1.882", "1.778", "1.684", "1.600", "1.523", "1.455", "1.391", "1.333", "1.280", "1.231", "1.185", "1.143", "1.063", "1.000", "0.944", "0.895", "0.85", "0.81", "0.773", "0.739", "0.708", "0.680", "0.654", "0.630", "0.607", "0.586", "0.567", "0.548", "0.500", "0.471", "0.444", "0.421", "0.400", "0.381", "0.364", "0.348", "0.333", "0.320", "0.308", "0.296", "0.286", "0.276", "0.267", "0.258", "0.250", "0.236", "0.222", "0.211", "0.200", "0.190", "0.182", "0.174", "0.167", "0.160", "0.154", "0.148", "0.143", "0.138", "0.133", "0.129", "0.125", "0.118", "0.111" knock_sens01 = bits, U08, 116, [0:0], "1", "2" knock_sens02 = bits, U08, 117, [0:0], "1", "2" knock_sens03 = bits, U08, 118, [0:0], "1", "2" knock_sens04 = bits, U08, 119, [0:0], "1", "2" knock_sens05 = bits, U08, 120, [0:0], "1", "2" knock_sens06 = bits, U08, 121, [0:0], "1", "2" knock_sens07 = bits, U08, 122, [0:0], "1", "2" knock_sens08 = bits, U08, 123, [0:0], "1", "2" knock_sens09 = bits, U08, 124, [0:0], "1", "2" knock_sens10 = bits, U08, 125, [0:0], "1", "2" knock_sens11 = bits, U08, 126, [0:0], "1", "2" knock_sens12 = bits, U08, 127, [0:0], "1", "2" knock_sens13 = bits, U08, 128, [0:0], "1", "2" knock_sens14 = bits, U08, 129, [0:0], "1", "2" knock_sens15 = bits, U08, 130, [0:0], "1", "2" knock_sens16 = bits, U08, 131, [0:0], "1", "2" s16_debug = scalar, S16, 132, "", 1, 0.00000, -32768, +32767, 0 u08_debug134 = scalar, U08, 134, "", 1, 0.00000, 0, +255, 0 AE_options = bits, U08, 135, [0:0], "Time-based AE", "Accel-pump AE" accel_blend_percent = scalar, S16, 136, "%", 0.1, 0.0, 0, 100, 1 accel_tpsdot_threshold = scalar, U16, 138, "%/sec", 0.1, 0, 0, 3276, 0 accel_mapdot_threshold = scalar, U16, 140, "kpa/sec", 1, 0, 0, 20000, 0 accel_mapdots = array, S16, 142, [8], "kpa/sec", 1, 0, -5000, 5000, 0 accel_tpsdots = array, S16, 158, [8], "%/sec", 0.1, 0, -3000, 3000, 1 accel_mapdot_amts = array, S16, 174, [8], "%", 0.1, 0, -500, 500, 1 accel_tpsdot_amts = array, S16, 190, [8], "%", 0.1, 0, -500, 500, 1 accel_CLT_multiplier = scalar, S16, 206, "%", 0.1, 0, 100, 255, 1 cl_idle_timing_target_deltas = array, S16, 208, [8], "rpm", 1, 0, -1000, 1000, 0 cl_idle_timing_advance_deltas = array, S16, 224, [8], "deg", 0.1, 0, -90, 90, 0 ltt_opt_on = bits, U08, 240, [0:0], "Off", "On" ltt_opt_mode = bits, U08, 240, [1:1], "Timed", "Button" ltt_opt_feedback = bits, U08, 240, [2:2], "Off", "On" ltt_but_in = bits, U08, 241, [0:4], "INVALID", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "INVALID", "INVALID", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" ltt_int = scalar, U08, 242, "min", 1, 0.00000, 5, 30, 0 ltt_led_out = bits, U08, 243, [0:5], "Off", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "CANOUT1", "CANOUT2", "CANOUT3", "CANOUT4", "CANOUT5", "CANOUT6", "CANOUT7", "CANOUT8", "CANOUT9", "CANOUT10", "CANOUT11", "CANOUT12", "CANOUT13", "CANOUT14", "CANOUT15", "CANOUT16" ltt_thresh = scalar, U16, 244, "%", 0.1, 0.0, 10, 65535, 1 tc_minmap = scalar, S16, 246, "%", 0.10000, 0.00000, 0, 100, 1 can_bcast1_on = bits, U08, 248, [0:0], "Off", "On" can_bcast1_280x4 = bits, U08, 248, [1:1], "Off", "On" can_bcast1_280x1 = bits, U08, 248, [2:2], "Off", "On" can_bcast1_289 = bits, U08, 248, [3:3], "Off", "On" can_bcast1_316 = bits, U08, 248, [4:4], "Off", "On" can_bcast1_329 = bits, U08, 248, [5:5], "Off", "On" can_bcast1_561 = bits, U08, 248, [6:6], "Off", "On" can_bcast1_361 = bits, U08, 248, [7:7], "Off", "On" can_bcast2_041 = bits, U08, 249, [0:0], "Off", "On" can_bcast_int = scalar, U16, 250, "ms", 0.128, 0.00000, 50, 1000,1 timedout1_in = bits, U08, 252, [0:4], "Off", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "INVALID", "Same as launch", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" timedout1_out = bits, U08, 253, [0:5], "Off", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "CANOUT1", "CANOUT2", "CANOUT3", "CANOUT4", "CANOUT5", "CANOUT6", "CANOUT7", "CANOUT8", "CANOUT9", "CANOUT10", "CANOUT11", "CANOUT12", "CANOUT13", "CANOUT14", "CANOUT15", "CANOUT16" timedout1_offdelay = scalar, U16, 254, "s", 0.001, 0, 0, 15, 3 tstop_out = bits, U08, 256, [0:5], "Off", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "CANOUT1", "CANOUT2", "CANOUT3", "CANOUT4", "CANOUT5", "CANOUT6", "CANOUT7", "CANOUT8", "CANOUT9", "CANOUT10", "CANOUT11", "CANOUT12", "CANOUT13", "CANOUT14", "CANOUT15", "CANOUT16" can_enable_on = bits, U08, 257, [0:0], "Off", "On" tstop_delay = scalar, U16, 258, "s", 0.001, 0, 0, 15, 3 tstop_hold = scalar, U16, 260, "s", 0.001, 0, 0, 15, 3 oddfireangs1 = scalar, U16, 262, "", 0.10000, 0.00000, 0.00, 720.00, 0 ; * ( 2 byte) oddfireangs2 = scalar, U16, 264, "", 0.10000, 0.00000, 0.00, 720.00, 0 ; * ( 2 byte) oddfireangs3 = scalar, U16, 266, "", 0.10000, 0.00000, 0.00, 720.00, 0 ; * ( 2 byte) oddfireangs4 = scalar, U16, 268, "", 0.10000, 0.00000, 0.00, 720.00, 0 ; * ( 2 byte) oddfireangs5 = scalar, U16, 270, "", 0.10000, 0.00000, 0.00, 720.00, 0 ; * ( 2 byte) oddfireangs6 = scalar, U16, 272, "", 0.10000, 0.00000, 0.00, 720.00, 0 ; * ( 2 byte) cel_opt_on = bits, U08, 274, [0:0], "Off", "On" cel_opt_stat = bits, U08, 274, [1:3], "Off", "MAP", "MAT", "CLT", "TPS", "Batt", "EGO", "EGT1" cel_opt_adc = bits, U08, 274, [5:5], "Fluctuation", "ADC counts" cel_opt_flash = bits, U08, 274, [6:6], "Solid", "Flash-codes" cel_opt_when = bits, U08, 274, [7:7], "Off", "On" cel_port = bits, U08, 275, [0:5], "Off", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "CANOUT1", "CANOUT2", "CANOUT3", "CANOUT4", "CANOUT5", "CANOUT6", "CANOUT7", "CANOUT8", "CANOUT9", "CANOUT10", "CANOUT11", "CANOUT12", "CANOUT13", "CANOUT14", "CANOUT15", "CANOUT16" afr_min = scalar, U08, 276, "AFR", 0.10000, 0.00000, 0.00, 25.5, 1 ; afr_max = scalar, U08, 277, "AFR", 0.10000, 0.00000, 0.00, 25.5, 1 ; afr_var_upper = scalar, U16, 278, "", 1, 0, 0.00, 65535, 0 afr_var_lower = scalar, U16, 280, "", 1, 0, 0.00, 65535, 0 map_minadc = scalar, U16, 282, "", 1, 0, 0.00, 1023, 0 map_maxadc = scalar, U16, 284, "", 1, 0, 0.00, 1023, 0 map_var_upper = scalar, U16, 286, "", 1, 0, 0.00, 65535, 0 mat_minadc = scalar, U16, 288, "", 1, 0, 0.00, 1023, 0 mat_maxadc = scalar, U16, 290, "", 1, 0, 0.00, 1023, 0 mat_var_upper = scalar, U16, 292, "", 1, 0, 0.00, 65535, 0 clt_minadc = scalar, U16, 294, "", 1, 0, 0.00, 1023, 0 clt_maxadc = scalar, U16, 296, "", 1, 0, 0.00, 1023, 0 clt_var_upper = scalar, U16, 298, "", 1, 0, 0.00, 65535, 0 tps_minadc = scalar, U16, 300, "", 1, 0, 0.00, 1023, 0 tps_maxadc = scalar, U16, 302, "", 1, 0, 0.00, 1023, 0 tps_var_upper = scalar, U16, 304, "", 1, 0, 0.00, 65535, 0 batt_minv = scalar, U08, 306, "", 0.1, 0, 7.00, 23.0, 1 batt_maxv = scalar, U08, 307, "", 0.1, 0, 7.00, 23.0, 1 batt_var_upper = scalar, U16, 308, "", 1, 0, 0.00, 65535, 0 cel_opt2_map = bits, U08, 310, [0:0], "Off", "On" cel_opt2_mat = bits, U08, 310, [1:1], "Off", "On" cel_opt2_clt = bits, U08, 310, [2:2], "Off", "On" cel_opt2_tps = bits, U08, 310, [3:3], "Off", "On" cel_opt2_batt = bits, U08, 310, [4:4], "Off", "On" cel_opt2_afr0 = bits, U08, 310, [5:5], "Off", "On" cel_opt2_sync = bits, U08, 310, [6:6], "Off", "On" cel_opt2_egt = bits, U08, 310, [7:7], "Off", "On" cel_action1_map = bits, U08, 311, [0:0], "Off", "On" cel_action1_mat = bits, U08, 311, [1:1], "Off", "On" cel_action1_clt = bits, U08, 311, [2:2], "Off", "On" cel_action1_tps = bits, U08, 311, [3:3], "Off", "On" cel_action1_batt= bits, U08, 311, [4:4], "Off", "On" cel_action1_ego = bits, U08, 311, [5:5], "Off", "On" cel_action1_sync = bits, U08, 311, [6:6], "Off", "On" cel_action1_map_an = bits, U08, 311, [7:7], "Off", "On" #if CELSIUS cel_clt_cold = scalar, S16, 312, "°C", 0.05555, -320.000,-40.00, {clthighlim}, 1 cel_clt_warm = scalar, S16, 314, "°C", 0.05555, -320.000,-40.00, {clthighlim}, 1 #else cel_clt_cold = scalar, S16, 312, "°F", 0.10000, 0.00000,-40.00, {clthighlim}, 1 cel_clt_warm = scalar, S16, 314, "°F", 0.10000, 0.00000,-40.00, {clthighlim}, 1 #endif cel_warmtime = scalar, U16, 316, "mins", 0.01666, 9, 1, 20,1 #if CELSIUS cel_mat_default = scalar, S16, 318, "°C", 0.05555, -320.000,-40.00, {clthighlim}, 1 #else cel_mat_default = scalar, S16, 318, "°F", 0.10000, 0.00000,-40.00, {clthighlim}, 1 #endif cel_revlim = scalar, S16, 320, "RPM", 1.00000, 0.00000, 0.00,{rpmhigh}, 0 cel_overboost = scalar, S16, 322, "kPa", 0.10000, 0.00000, 0.00, {loadhigh}, 1 cel_boost_duty = scalar, U08, 324, "%", 1, 0.00000, 0, 100, 0 cel_boost_duty2 = scalar, U08, 325, "%", 1, 0.00000, 0, 100, 0 cel_synctol = scalar, U08, 326, "", 1, 0.00000, 0, 100, 0 cel_opt3_flex = bits, U08, 327, [0:0], "Off", "On" cel_retard = scalar, S16, 328, "deg", 0.10000, 0.00000,0.00, 10.00, 1 map_var_lower = scalar, U16, 330, "", 1, 0, 0.00, 65535, 0 #if CELSIUS egt_minvalid = scalar, S16, 332, "°C", 0.05555, -320.000,-40.00, 1500, 1 egt_maxvalid = scalar, S16, 334, "°C", 0.05555, -320.000,-40.00, 1500, 1 #else egt_minvalid = scalar, S16, 332, "°F", 0.10000, 0.00000,-40.00, 2700, 1 egt_maxvalid = scalar, S16, 334, "°F", 0.10000, 0.00000,-40.00, 2700, 1 #endif egt_var_upper = scalar, U16, 336, "", 1, 0, 0.00, 65535, 0 egt_var_lower = scalar, U16, 338, "", 1, 0, 0.00, 65535, 0 cel_runtime = scalar, U08, 340, "s", 1, 0.00000, 5, 100, 0 cel_action2_flex = bits, U08, 341, [0:0], "Off", "On" cel_action2_egt = bits, U08, 341, [1:1], "Off", "On" blend_opt1 = bits, U08, 342, [0:4], "TPS", "MAP", "RPM", "MAFload", "Flex%", "VSS1", "Gear", "RPM*load/100", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Sensor 1", "Sensor 2","Sensor 3","Sensor 4","Sensor 5","Sensor 6","Sensor 7","Sensor 8","Sensor 9","Sensor 10","Sensor 11","Sensor 12","Sensor 13","Sensor 14","Sensor 15","Sensor 16" blend_opt2 = bits, U08, 343, [0:4], "TPS", "MAP", "RPM", "MAFload", "Flex%", "VSS1", "Gear", "RPM*load/100", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Sensor 1", "Sensor 2","Sensor 3","Sensor 4","Sensor 5","Sensor 6","Sensor 7","Sensor 8","Sensor 9","Sensor 10","Sensor 11","Sensor 12","Sensor 13","Sensor 14","Sensor 15","Sensor 16" blend_opt3 = bits, U08, 344, [0:4], "TPS", "MAP", "RPM", "MAFload", "Flex%", "VSS1", "Gear", "RPM*load/100", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Sensor 1", "Sensor 2","Sensor 3","Sensor 4","Sensor 5","Sensor 6","Sensor 7","Sensor 8","Sensor 9","Sensor 10","Sensor 11","Sensor 12","Sensor 13","Sensor 14","Sensor 15","Sensor 16" blend_opt4 = bits, U08, 345, [0:4], "TPS", "MAP", "RPM", "MAFload", "Flex%", "VSS1", "Gear", "RPM*load/100", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Sensor 1", "Sensor 2","Sensor 3","Sensor 4","Sensor 5","Sensor 6","Sensor 7","Sensor 8","Sensor 9","Sensor 10","Sensor 11","Sensor 12","Sensor 13","Sensor 14","Sensor 15","Sensor 16" blend_opt5 = bits, U08, 346, [0:4], "TPS", "MAP", "RPM", "MAFload", "Flex%", "VSS1", "Gear", "RPM*load/100", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Sensor 1", "Sensor 2","Sensor 3","Sensor 4","Sensor 5","Sensor 6","Sensor 7","Sensor 8","Sensor 9","Sensor 10","Sensor 11","Sensor 12","Sensor 13","Sensor 14","Sensor 15","Sensor 16" blend_opt6 = bits, U08, 347, [0:4], "TPS", "MAP", "RPM", "MAFload", "Flex%", "VSS1", "Gear", "RPM*load/100", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Sensor 1", "Sensor 2","Sensor 3","Sensor 4","Sensor 5","Sensor 6","Sensor 7","Sensor 8","Sensor 9","Sensor 10","Sensor 11","Sensor 12","Sensor 13","Sensor 14","Sensor 15","Sensor 16" blend_opt7 = bits, U08, 348, [0:4], "TPS", "MAP", "RPM", "MAFload", "Flex%", "VSS1", "Gear", "RPM*load/100", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Sensor 1", "Sensor 2","Sensor 3","Sensor 4","Sensor 5","Sensor 6","Sensor 7","Sensor 8","Sensor 9","Sensor 10","Sensor 11","Sensor 12","Sensor 13","Sensor 14","Sensor 15","Sensor 16" ;gap in case of more blend curve options fp_opt_mode = bits, U08, 350, [0:1], "On/Off", "Open-Loop PWM", "Closed-Loop PWM", "INVALID" fp_opt_reg = bits, U08, 350, [4:5], "Vac referenced", "Fixed pressure", "Custom correction", "INVALID" fp_opt_inv = bits, U08, 350, [6:6], "Normal", "Inverted" fp_opt_safety = bits, U08, 350, [7:7], "Off", "On" fp_out1 = bits, U08, 351, [0:5], "Fuel Pump", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" rail_pressure_psig = scalar, U16, 352, "psi.g", 0.0147, 0.00000, 0, 100, 1 rail_pressure_kpag = scalar, U16, 352, "kPa.g", 0.1, 0.00000, 0, 680, 1 fp_Kp = scalar, U16, 354, "%", 0.1, 0.00000, 0, 200, 1 fp_Ki = scalar, U16, 356, "%", 0.1, 0.00000, 0, 200, 1 fp_Kd = scalar, U16, 358, "%", 0.1, 0.00000, 0, 200, 1 fp_prime_duty = scalar, U08, 360, "%", 0.392, 0.00000, 0, 100, 1 fp_press_in = bits, U08, 361, [0:3], "Off","Sensor 1", "Sensor 2","Sensor 3","Sensor 4","Sensor 5","Sensor 6","Sensor 7","Sensor 8","Sensor 9","Sensor 10","Sensor 11","Sensor 12","Sensor 13","Sensor 14","Sensor 15" ; note off by 1 fp_press_type = bits, U08, 361, [6:7], "Gauge", "Absolute", "Differential", "INVALID" fp_freq = bits, U08, 362, [0:3], "INVALID", "INVALID", "250Hz", "225Hz", "200Hz", "175Hz", "150Hz", "125Hz", "100Hz", "78Hz", "39Hz", "26Hz", "19.5Hz", "15.6Hz", "13Hz", "11.1Hz" ;spare alternator_opt_mode = bits, U08, 364, [0:2], "Off", "On-Off", "Open-loop frequency", "Open-loop duty", "Closed-loop field control", "High-speed feedback field control", "INVALID", "INVALID" ; possible application specific option bits alternator_freq = bits, U08, 365, [0:3], "INVALID", "INVALID", "250Hz", "225Hz", "200Hz", "175Hz", "150Hz", "125Hz", "100Hz", "78Hz", "39Hz", "26Hz", "19.5Hz", "15.6Hz", "13Hz", "11.1Hz" alternator_controlout = bits, U08, 366, [0:4], "INVALID", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" alternator_control_inv = bits, U08, 366, [6:6], "Normal", "Inverted" alternator_lampout = bits, U08, 367, [0:5], "Off", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "CANOUT1", "CANOUT2", "CANOUT3", "CANOUT4", "CANOUT5", "CANOUT6", "CANOUT7", "CANOUT8", "CANOUT9", "CANOUT10", "CANOUT11", "CANOUT12", "CANOUT13", "CANOUT14", "CANOUT15", "CANOUT16" alternator_Kp = scalar, U16, 368, "%", 0.1, 0.00000, 0, 200, 1 alternator_Ki = scalar, U16, 370, "%", 0.1, 0.00000, 0, 200, 1 alternator_Kd = scalar, U16, 372, "%", 0.1, 0.00000, 0, 200, 1 alternator_startdelay = scalar, U08, 374, "s", 0.1, 0.00000, 0, 25.5, 1 alternator_ramptime = scalar, U08, 375, "s", 0.1, 0.00000, 0, 25.5, 1 alternator_wot = scalar, U16, 376, "%", 0.1, 0.00000, 0, 110, 1 alternator_wotv = scalar, U08, 378, "V", 0.1, 0.00000, 10.0, 15.0, 1 alternator_overrv = scalar, U08, 379, "V", 0.1, 0.00000, 10.0, 15.0, 1 alternator_wottimeout = scalar, U08, 380, "s", 1, 0.00000, 0, 30, 0 alternator_tempin = bits, U08, 381, [0:3], "Off","Sensor 1", "Sensor 2","Sensor 3","Sensor 4","Sensor 5","Sensor 6","Sensor 7","Sensor 8","Sensor 9","Sensor 10","Sensor 11","Sensor 12","Sensor 13","Sensor 14","Sensor 15" ; note off by 1 alternator_freq_monin = bits, U08, 382, [0:4], "Off", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "INVALID", "INVALID", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" alternator_freq_moninv = bits, U08, 382, [6:6], "Normal", "Inverted" alternator_targv = scalar, U08, 383, "V", 0.1, 0.00000, 10.0, 15.0, 1 alternator_ctl_ms = scalar, U16, 384, "ms", 0.128, 0.00000, 10, 500, 0 fp_ctl_ms = scalar, U16, 386, "ms", 0.128, 0.00000, 10, 500, 0 alternator_freq_currin = bits, U08, 388, [0:4], "Off", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "INVALID", "INVALID", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" alternator_freq_currinv = bits, U08, 388, [6:6], "Normal", "Inverted" alternator_chargetime = scalar, U08, 389, "min", 1, 0.00000, 0, 30, 0 alternator_targvr = scalar, U08, 390, "V", 0.1, 0.00000, 10.0, 15.0, 1 alternator_diff = scalar, U08, 391, "V", 0.1, 0.00000, 0.1, 3.0, 1 alternator_maxload = scalar, U08, 392, "%", 1, 0.00000, 75, 101, 0 hpte_opt_on = bits, U08, 393, [0:0], "Off","On" hpte_load = scalar, S16, 394, "%", 0.10000, 0, 0, {loadhigh}, 1 hpte_rpm = scalar, U16, 396, "rpm", 1, 0, 0, {rpmhigh}, 0 shiftlight_opt_pins = bits, U08, 398, [0:5], "Off", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "CANOUT1", "CANOUT2", "CANOUT3", "CANOUT4", "CANOUT5", "CANOUT6", "CANOUT7", "CANOUT8", "CANOUT9", "CANOUT10", "CANOUT11", "CANOUT12", "CANOUT13", "CANOUT14", "CANOUT15", "CANOUT16" shiftlight_opt_gear = bits, U08, 398, [7:7], "Off", "On" fc_trans_time_ret = scalar, U08, 399, "s", 0.1, 0, 0.5, 5.0, 1 shiftlight_limit1 = scalar, U16, 400, "rpm", 1, 0, 0, {rpmhigh}, 0 shiftlight_limit2 = scalar, U16, 402, "rpm", 1, 0, 0, {rpmhigh}, 0 shiftlight_limit3 = scalar, U16, 404, "rpm", 1, 0, 0, {rpmhigh}, 0 shiftlight_limit4 = scalar, U16, 406, "rpm", 1, 0, 0, {rpmhigh}, 0 shiftlight_limit5 = scalar, U16, 408, "rpm", 1, 0, 0, {rpmhigh}, 0 shiftlight_limit6 = scalar, U16, 410, "rpm", 1, 0, 0, {rpmhigh}, 0 ltt_samp_time = scalar, U08, 412, "s", 1, 0, 0, 255, 0 ltt_agg = scalar, U08, 413, "", 1, 0, 10, 255, 0 oilpress_in = bits, U08, 414, [0:3], "Off","Sensor 1", "Sensor 2","Sensor 3","Sensor 4","Sensor 5","Sensor 6","Sensor 7","Sensor 8","Sensor 9","Sensor 10","Sensor 11","Sensor 12","Sensor 13","Sensor 14","Sensor 15" ; note off by 1 oilpress_out = bits, U08, 415, [0:5], "Off", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "CANOUT1", "CANOUT2", "CANOUT3", "CANOUT4", "CANOUT5", "CANOUT6", "CANOUT7", "CANOUT8", "CANOUT9", "CANOUT10", "CANOUT11", "CANOUT12", "CANOUT13", "CANOUT14", "CANOUT15", "CANOUT16" fuelcalctime = scalar, U16, 416, "ms", 0.128, 0, 100, 8000, 0 alternator_sensitivity = scalar, U16, 420, "", 0.1, 0.00000, 0, 20, 0 idleminvss = scalar, U16, 422, { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, { msToPrefUnitsScale }, 0.00000, 0.00, 200, 0 ; * ( 2 bytes) flex_baseline = scalar, U16, 424, "%", 0.1, 0.00000, 0, 100,1 fc_transition_time = scalar, U08, 426, "s", 0.1, 0, 0.5, 5.0, 1 fc_ae_time = scalar, U08, 427, "s", 0.01, 0, 0, 0.5, 2 fc_timing = scalar, S16, 428, "deg", 0.10000, 0.00000, -90.0, 180.00, 2 ; * ( 2 bytes) fc_ae_pct = scalar, U08, 430, "%ReqFuel", 1, 0.00000, 0, 255, 0 ; * ( 1 byte) fp_off_duty = scalar, U08, 431, "%", 0.392, 0.00000, 0, 100, 1 fp_min_duty = scalar, U08, 432, "%", 0.392, 0.00000, 0, 100, 1 fp_max_duty = scalar, U08, 433, "%", 0.392, 0.00000, 0, 100, 1 tcs_in = bits, U08, 434, [0:4], "Off", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "INVALID", "INVALID", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" tcs_moves = scalar, U08, 435, "", 1, 0, 1, 50, 0 tcs_offtime = scalar, U16, 436, "s", 0.001, 0, 0.005, 0.100, 3 tcs_ontime = scalar, U16, 438, "s", 0.001, 0, 0.050, 0.200, 3 boost_geartarg1 = scalar, S16, 440, "kPa", 0.10000, 0.00000, 0.00, {loadhigh}, 1 boost_geartarg2 = scalar, S16, 442, "kPa", 0.10000, 0.00000, 0.00, {loadhigh}, 1 boost_geartarg3 = scalar, S16, 444, "kPa", 0.10000, 0.00000, 0.00, {loadhigh}, 1 boost_geartarg4 = scalar, S16, 446, "kPa", 0.10000, 0.00000, 0.00, {loadhigh}, 1 boost_geartarg5 = scalar, S16, 448, "kPa", 0.10000, 0.00000, 0.00, {loadhigh}, 1 boost_geartarg6 = scalar, S16, 450, "kPa", 0.10000, 0.00000, 0.00, {loadhigh}, 1 fp_drop_psig = scalar, U16, 452, "psi.g", 0.0147, 0.00000, 0, 100, 1 fp_drop_kpag = scalar, U16, 452, "kPa.g", 0.1, 0.00000, 0, 680, 1 fp_drop_load = scalar, U16, 454, "%", 0.1, 0, 0, {loadhigh}, 1 fp_drop_rpm = scalar, U16, 456, "rpm", 1, 0, 0, {rpmhigh}, 0 fp_drop_time = scalar, U16, 458, "s", 0.001,0, 0, 10, 2 pwm_opt_load_a_offset = scalar, U16, 460, "", 1, 0, 0, 65535, 0 pwm_opt_load_b_offset = scalar, U16, 462, "", 1, 0, 0, 65535, 0 pwm_opt_load_c_offset = scalar, U16, 464, "", 1, 0, 0, 65535, 0 pwm_opt_load_d_offset = scalar, U16, 466, "", 1, 0, 0, 65535, 0 pwm_opt_load_e_offset = scalar, U16, 468, "", 1, 0, 0, 65535, 0 pwm_opt_load_f_offset = scalar, U16, 470, "", 1, 0, 0, 65535, 0 pwm_opt_load_a_size = scalar, U08, 472, "", 1, 0, 0, 255, 0 pwm_opt_load_b_size = scalar, U08, 473, "", 1, 0, 0, 255, 0 pwm_opt_load_c_size = scalar, U08, 474, "", 1, 0, 0, 255, 0 pwm_opt_load_d_size = scalar, U08, 475, "", 1, 0, 0, 255, 0 pwm_opt_load_e_size = scalar, U08, 476, "", 1, 0, 0, 255, 0 pwm_opt_load_f_size = scalar, U08, 477, "", 1, 0, 0, 255, 0 can_gps_id = scalar, U08, 478, "", 1.00000, 0.00000, 0.00, 14, 0 ; can_gps_table = scalar, U08, 479, "", 1.00000, 0.00000, 0, 15, 0 ; * ( 1 byte) can_gps_offset = scalar, U16, 480, "bytes", 1.00000, 0.00000, 0, 4095, 0 spkadj_max = scalar, S16, 482, "deg", 0.10000, 0.00000,0, 45, 1 spkadj_min = scalar, S16, 484, "deg", 0.10000, 0.00000,-45, 0, 1 ; somewhat big gap here ; ###### ### ##### ##### # ###### ; # # # # # # # # # # # ; # # # # # # # # # ; ###### # # #### # #### # # ###### ; # # # # # # # ####### # ; # # # # # # # # # # ; ###### ### ##### ##### # # # ; ; big pad dummyfield = bits, U08, 637, [0:0], "","" staged_out2 = bits, U08, 638, [0:5], "Off", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "CANOUT1", "CANOUT2", "CANOUT3", "CANOUT4", "CANOUT5", "CANOUT6", "CANOUT7", "CANOUT8", "CANOUT9", "CANOUT10", "CANOUT11", "CANOUT12", "CANOUT13", "CANOUT14", "CANOUT15", "CANOUT16" staged_out2_inv = bits, U08, 638, [7:7], "Normal", "Inverted" staged_out2_time = scalar, U08, 639, "s", 0.1, 0, 0, 1, 1 u16_debug640 = scalar, U16, 640, "", 1, 0.00000, 0, 65536, 0 staged_out1 = bits, U08, 642, [0:5], "Off", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "CANOUT1", "CANOUT2", "CANOUT3", "CANOUT4", "CANOUT5", "CANOUT6", "CANOUT7", "CANOUT8", "CANOUT9", "CANOUT10", "CANOUT11", "CANOUT12", "CANOUT13", "CANOUT14", "CANOUT15", "CANOUT16" staged_out1_inv = bits, U08, 642, [7:7], "Normal", "Inverted" log_style4_opt = bits, U08, 643, [0:0], "RPM", "TPS" log_trig_rpm = scalar, U16, 644, "RPM", 1, 0, 0, {rpmhigh}, 0 log_trig_tps = scalar, U16, 646, "%", 0.1, 0, 0, 100, 0 baudhigh = scalar, U32, 648, "", 1.00000, 0.00000,9600.0,500000.0, 0 ; x ( 4 bytes) fuelCorr_default = scalar, U08, 652, "%", 1.00000, 0.00000, 50, 255, 0 ;pad 653 fuelSpkDel_default = scalar, S16, 654, "deg", 0.10000, 0.00000,-45.00, 45.00, 1 map_phase_thresh = scalar, S16, 656, "kPa", 0.10000, 0.00000, 0.00, {loadhigh}, 1 flex_pct0 = scalar, U16, 658, "%", 0.1, 0.00000, 0, 100,1 flex_pct1 = scalar, U16, 660, "%", 0.1, 0.00000, 0, 100,1 ;generic sensors sensor01_source = bits, U08, 662, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" sensor02_source = bits, U08, 663, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" sensor03_source = bits, U08, 664, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" sensor04_source = bits, U08, 665, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" sensor05_source = bits, U08, 666, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" sensor06_source = bits, U08, 667, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" sensor07_source = bits, U08, 668, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" sensor08_source = bits, U08, 669, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" sensor09_source = bits, U08, 670, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" sensor10_source = bits, U08, 671, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" sensor11_source = bits, U08, 672, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" sensor12_source = bits, U08, 673, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" sensor13_source = bits, U08, 674, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" sensor14_source = bits, U08, 675, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" sensor15_source = bits, U08, 676, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" sensor16_source = bits, U08, 677, [0:4], "Off", "JS5 (ADC6)", "JS4 (ADC7)", "EXT_MAP (ADC11)", "EGO2 (ADC12)", "Spare ADC (ADC13)", "INVALID", "INVALID", "CAN ADC01", "CAN ADC02", "CAN ADC03", "CAN ADC04", "CAN ADC05", "CAN ADC06", "CAN ADC07", "CAN ADC08", "CAN ADC09", "CAN ADC10", "CAN ADC11", "CAN ADC12", "CAN ADC13", "CAN ADC14", "CAN ADC15", "CAN ADC16", "CAN ADC17", "CAN ADC18", "CAN ADC19", "CAN ADC20", "CAN ADC21", "CAN ADC22", "CAN ADC23", "CAN ADC24" sensor01_trans = bits, U08, 678, [0:2], "Raw", "Linear", "Same as MAP", "Same as CLT", "Same as MAT", "Same as EGO", "Same as MAF", "GM calibration" sensor02_trans = bits, U08, 679, [0:2], "Raw", "Linear", "Same as MAP", "Same as CLT", "Same as MAT", "Same as EGO", "Same as MAF", "GM calibration" sensor03_trans = bits, U08, 680, [0:2], "Raw", "Linear", "Same as MAP", "Same as CLT", "Same as MAT", "Same as EGO", "Same as MAF", "GM calibration" sensor04_trans = bits, U08, 681, [0:2], "Raw", "Linear", "Same as MAP", "Same as CLT", "Same as MAT", "Same as EGO", "Same as MAF", "GM calibration" sensor05_trans = bits, U08, 682, [0:2], "Raw", "Linear", "Same as MAP", "Same as CLT", "Same as MAT", "Same as EGO", "Same as MAF", "GM calibration" sensor06_trans = bits, U08, 683, [0:2], "Raw", "Linear", "Same as MAP", "Same as CLT", "Same as MAT", "Same as EGO", "Same as MAF", "GM calibration" sensor07_trans = bits, U08, 684, [0:2], "Raw", "Linear", "Same as MAP", "Same as CLT", "Same as MAT", "Same as EGO", "Same as MAF", "GM calibration" sensor08_trans = bits, U08, 685, [0:2], "Raw", "Linear", "Same as MAP", "Same as CLT", "Same as MAT", "Same as EGO", "Same as MAF", "GM calibration" sensor09_trans = bits, U08, 686, [0:2], "Raw", "Linear", "Same as MAP", "Same as CLT", "Same as MAT", "Same as EGO", "Same as MAF", "GM calibration" sensor10_trans = bits, U08, 687, [0:2], "Raw", "Linear", "Same as MAP", "Same as CLT", "Same as MAT", "Same as EGO", "Same as MAF", "GM calibration" sensor11_trans = bits, U08, 688, [0:2], "Raw", "Linear", "Same as MAP", "Same as CLT", "Same as MAT", "Same as EGO", "Same as MAF", "GM calibration" sensor12_trans = bits, U08, 689, [0:2], "Raw", "Linear", "Same as MAP", "Same as CLT", "Same as MAT", "Same as EGO", "Same as MAF", "GM calibration" sensor13_trans = bits, U08, 690, [0:2], "Raw", "Linear", "Same as MAP", "Same as CLT", "Same as MAT", "Same as EGO", "Same as MAF", "GM calibration" sensor14_trans = bits, U08, 691, [0:2], "Raw", "Linear", "Same as MAP", "Same as CLT", "Same as MAT", "Same as EGO", "Same as MAF", "GM calibration" sensor15_trans = bits, U08, 692, [0:2], "Raw", "Linear", "Same as MAP", "Same as CLT", "Same as MAT", "Same as EGO", "Same as MAF", "GM calibration" sensor16_trans = bits, U08, 693, [0:2], "Raw", "Linear", "Same as MAP", "Same as CLT", "Same as MAT", "Same as EGO", "Same as MAF", "GM calibration" sensor01_val0 = scalar, S16, 694, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor02_val0 = scalar, S16, 696, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor03_val0 = scalar, S16, 698, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor04_val0 = scalar, S16, 700, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor05_val0 = scalar, S16, 702, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor06_val0 = scalar, S16, 704, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor07_val0 = scalar, S16, 706, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor08_val0 = scalar, S16, 708, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor09_val0 = scalar, S16, 710, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor10_val0 = scalar, S16, 712, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor11_val0 = scalar, S16, 714, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor12_val0 = scalar, S16, 716, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor13_val0 = scalar, S16, 718, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor14_val0 = scalar, S16, 720, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor15_val0 = scalar, S16, 722, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor16_val0 = scalar, S16, 724, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor01_max = scalar, S16, 726, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor02_max = scalar, S16, 728, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor03_max = scalar, S16, 730, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor04_max = scalar, S16, 732, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor05_max = scalar, S16, 734, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor06_max = scalar, S16, 736, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor07_max = scalar, S16, 738, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor08_max = scalar, S16, 740, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor09_max = scalar, S16, 742, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor10_max = scalar, S16, 744, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor11_max = scalar, S16, 746, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor12_max = scalar, S16, 748, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor13_max = scalar, S16, 750, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor14_max = scalar, S16, 752, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor15_max = scalar, S16, 754, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor16_max = scalar, S16, 756, "", 0.10000, 0.00000, -3276.7, 3276.7, 1 ; * ( 2 bytes) sensor01LF = scalar, U08, 758, "", 1,0,10,100,0 sensor02LF = scalar, U08, 759, "", 1,0,10,100,0 sensor03LF = scalar, U08, 760, "", 1,0,10,100,0 sensor04LF = scalar, U08, 761, "", 1,0,10,100,0 sensor05LF = scalar, U08, 762, "", 1,0,10,100,0 sensor06LF = scalar, U08, 763, "", 1,0,10,100,0 sensor07LF = scalar, U08, 764, "", 1,0,10,100,0 sensor08LF = scalar, U08, 765, "", 1,0,10,100,0 sensor09LF = scalar, U08, 766, "", 1,0,10,100,0 sensor10LF = scalar, U08, 767, "", 1,0,10,100,0 sensor11LF = scalar, U08, 768, "", 1,0,10,100,0 sensor12LF = scalar, U08, 769, "", 1,0,10,100,0 sensor13LF = scalar, U08, 770, "", 1,0,10,100,0 sensor14LF = scalar, U08, 771, "", 1,0,10,100,0 sensor15LF = scalar, U08, 772, "", 1,0,10,100,0 sensor16LF = scalar, U08, 773, "", 1,0,10,100,0 sensor_temp = bits, U08, 774, [0:0], "degF", "degC" ;pad #if PW_4X injOpen1 = scalar, U16, 776, "ms", 0.004, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) injOpen2 = scalar, U16, 778, "ms", 0.004, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) injOpen3 = scalar, U16, 780, "ms", 0.004, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) injOpen4 = scalar, U16, 782, "ms", 0.004, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) injOpen5 = scalar, U16, 784, "ms", 0.004, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) injOpen6 = scalar, U16, 786, "ms", 0.004, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) injOpen7 = scalar, U16, 788, "ms", 0.004, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) injOpen8 = scalar, U16, 790, "ms", 0.004, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) injOpena = scalar, U16, 792, "ms", 0.004, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) injOpenb = scalar, U16, 794, "ms", 0.004, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) ;next 8 not yet used injOpen11 = scalar, U16, 796, "ms", 0.004, 0.00000, 0.00, 25.50, 3 injOpen12 = scalar, U16, 798, "ms", 0.004, 0.00000, 0.00, 25.50, 3 injOpen13 = scalar, U16, 800, "ms", 0.004, 0.00000, 0.00, 25.50, 3 injOpen14 = scalar, U16, 802, "ms", 0.004, 0.00000, 0.00, 25.50, 3 injOpen15 = scalar, U16, 804, "ms", 0.004, 0.00000, 0.00, 25.50, 3 injOpen16 = scalar, U16, 806, "ms", 0.004, 0.00000, 0.00, 25.50, 3 injOpen17 = scalar, U16, 808, "ms", 0.004, 0.00000, 0.00, 25.50, 3 injOpen18 = scalar, U16, 810, "ms", 0.004, 0.00000, 0.00, 25.50, 3 #else injOpen1 = scalar, U16, 776, "ms", 0.001, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) injOpen2 = scalar, U16, 778, "ms", 0.001, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) injOpen3 = scalar, U16, 780, "ms", 0.001, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) injOpen4 = scalar, U16, 782, "ms", 0.001, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) injOpen5 = scalar, U16, 784, "ms", 0.001, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) injOpen6 = scalar, U16, 786, "ms", 0.001, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) injOpen7 = scalar, U16, 788, "ms", 0.001, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) injOpen8 = scalar, U16, 790, "ms", 0.001, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) injOpena = scalar, U16, 792, "ms", 0.001, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) injOpenb = scalar, U16, 794, "ms", 0.001, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) ;next 8 not yet used injOpen11 = scalar, U16, 796, "ms", 0.001, 0.00000, 0.00, 25.50, 3 injOpen12 = scalar, U16, 798, "ms", 0.001, 0.00000, 0.00, 25.50, 3 injOpen13 = scalar, U16, 800, "ms", 0.001, 0.00000, 0.00, 25.50, 3 injOpen14 = scalar, U16, 802, "ms", 0.001, 0.00000, 0.00, 25.50, 3 injOpen15 = scalar, U16, 804, "ms", 0.001, 0.00000, 0.00, 25.50, 3 injOpen16 = scalar, U16, 806, "ms", 0.001, 0.00000, 0.00, 25.50, 3 injOpen17 = scalar, U16, 808, "ms", 0.001, 0.00000, 0.00, 25.50, 3 injOpen18 = scalar, U16, 810, "ms", 0.001, 0.00000, 0.00, 25.50, 3 #endif shift_cut_on = bits, U08, 812, [0:0], "Off", "On" shift_cut_auto = bits, U08, 812, [1:1], "Button", "Auto" shift_cut_gear = bits, U08, 812, [2:2], "Off", "On" shift_cut_in = bits, U08, 813, [0:4], "INVALID", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "INVALID", "INVALID", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" shift_cut_out = bits, U08, 814, [0:5], "INVALID", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" shift_cut_rpm = scalar, U16, 815, "RPM", 1, 0, 0, {rpmhigh}, 0 shift_cut_tps = scalar, U16, 817, "%", 0.1, 0, 0, 100, 0 shift_cut_delay = scalar, U08, 819, "s", 0.01024, 0, 0, 2.55, 2 shift_cut_time = scalar, U08, 820, "s", 0.01024, 0, 0, 2.55, 2 shift_cut_add12 = scalar, U08, 821, "s", 0.01024, 0, 0, 2.55, 2 shift_cut_add23 = scalar, U08, 822, "s", 0.01024, 0, 0, 2.55, 2 shift_cut_add34 = scalar, U08, 823, "s", 0.01024, 0, 0, 2.55, 2 shift_cut_add45 = scalar, U08, 824, "s", 0.01024, 0, 0, 2.55, 2 shift_cut_add56 = scalar, U08, 825, "s", 0.01024, 0, 0, 2.55, 2 shift_cut_soldelay=scalar, U08, 826, "s", 0.01024, 0, 0, 2.55, 2 shift_cut_rpm12 = scalar, U16, 827, "RPM", 1, 0, 0, {rpmhigh}, 0 shift_cut_rpm23 = scalar, U16, 829, "RPM", 1, 0, 0, {rpmhigh}, 0 shift_cut_rpm34 = scalar, U16, 831, "RPM", 1, 0, 0, {rpmhigh}, 0 shift_cut_rpm45 = scalar, U16, 833, "RPM", 1, 0, 0, {rpmhigh}, 0 shift_cut_rpm56 = scalar, U16, 835, "RPM", 1, 0, 0, {rpmhigh}, 0 shift_cut_reshift= scalar, U08, 837, "s", 0.01024, 0, 0, 2.55, 2 ;open-loop PWM. all arrays pwm_opt_on_a = bits, U08, 838, [0:0], "Off", "On" pwm_opt_freq_a = bits, U08, 838, [1:4], "On-Off", "Variable Freq", "250Hz", "225Hz", "200Hz", "175Hz", "150Hz", "125Hz", "100Hz", "78Hz", "39Hz", "26Hz", "19.5Hz", "15.6Hz", "13Hz", "11.1Hz" pwm_opt_load_a = bits, U08, 838, [5:7], "RPM", "MAP", "% baro", "TPS", "MAFload", "CLT", "BattV", "MAT" ; ITB hidden pwm_opt_on_b = bits, U08, 839, [0:0], "Off", "On" pwm_opt_freq_b = bits, U08, 839, [1:4], "On-Off", "Variable Freq", "250Hz", "225Hz", "200Hz", "175Hz", "150Hz", "125Hz", "100Hz", "78Hz", "39Hz", "26Hz", "19.5Hz", "15.6Hz", "13Hz", "11.1Hz" pwm_opt_load_b = bits, U08, 839, [5:7], "RPM", "MAP", "% baro", "TPS", "MAFload", "CLT", "BattV", "MAT" pwm_opt_on_c = bits, U08, 840, [0:0], "Off", "On" pwm_opt_freq_c = bits, U08, 840, [1:4], "On-Off", "Variable Freq", "250Hz", "225Hz", "200Hz", "175Hz", "150Hz", "125Hz", "100Hz", "78Hz", "39Hz", "26Hz", "19.5Hz", "15.6Hz", "13Hz", "11.1Hz" pwm_opt_load_c = bits, U08, 840, [5:7], "RPM", "MAP", "% baro", "TPS", "MAFload", "CLT", "BattV", "MAT" pwm_opt_on_d = bits, U08, 841, [0:0], "Off", "On" pwm_opt_freq_d = bits, U08, 841, [1:4], "On-Off", "Variable Freq", "250Hz", "225Hz", "200Hz", "175Hz", "150Hz", "125Hz", "100Hz", "78Hz", "39Hz", "26Hz", "19.5Hz", "15.6Hz", "13Hz", "11.1Hz" pwm_opt_load_d = bits, U08, 841, [5:7], "RPM", "MAP", "% baro", "TPS", "MAFload", "CLT", "BattV", "MAT" pwm_opt_on_e = bits, U08, 842, [0:0], "Off", "On" pwm_opt_freq_e = bits, U08, 842, [1:4], "On-Off", "Variable Freq", "250Hz", "225Hz", "200Hz", "175Hz", "150Hz", "125Hz", "100Hz", "78Hz", "39Hz", "26Hz", "19.5Hz", "15.6Hz", "13Hz", "11.1Hz" pwm_opt_load_e = bits, U08, 842, [5:7], "RPM", "MAP", "% baro", "TPS", "MAFload", "CLT", "BattV", "MAT" pwm_opt_on_f = bits, U08, 843, [0:0], "Off", "On" pwm_opt_freq_f = bits, U08, 843, [1:4], "On-Off", "Variable Freq", "250Hz", "225Hz", "200Hz", "175Hz", "150Hz", "125Hz", "100Hz", "78Hz", "39Hz", "26Hz", "19.5Hz", "15.6Hz", "13Hz", "11.1Hz" pwm_opt_load_f = bits, U08, 843, [5:7], "RPM", "MAP", "% baro", "TPS", "MAFload", "CLT", "BattV", "MAT" pwm_opt2_a = bits, U08, 844, [0:5], "INVALID", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "CANPWM1", "CANPWM2", "CANPWM3", "CANPWM4", "CANPWM5", "CANPWM6", "CANPWM7", "CANPWM8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" pwm_opt2_b = bits, U08, 845, [0:5], "INVALID", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "CANPWM1", "CANPWM2", "CANPWM3", "CANPWM4", "CANPWM5", "CANPWM6", "CANPWM7", "CANPWM8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" pwm_opt2_c = bits, U08, 846, [0:5], "INVALID", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "CANPWM1", "CANPWM2", "CANPWM3", "CANPWM4", "CANPWM5", "CANPWM6", "CANPWM7", "CANPWM8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" pwm_opt2_d = bits, U08, 847, [0:5], "INVALID", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "CANPWM1", "CANPWM2", "CANPWM3", "CANPWM4", "CANPWM5", "CANPWM6", "CANPWM7", "CANPWM8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" pwm_opt2_e = bits, U08, 848, [0:5], "INVALID", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "CANPWM1", "CANPWM2", "CANPWM3", "CANPWM4", "CANPWM5", "CANPWM6", "CANPWM7", "CANPWM8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" pwm_opt2_f = bits, U08, 849, [0:5], "INVALID", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "CANPWM1", "CANPWM2", "CANPWM3", "CANPWM4", "CANPWM5", "CANPWM6", "CANPWM7", "CANPWM8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" pwm_onabove_a = scalar, U08, 850, "%", 1, 0, 0, 100, 0 pwm_onabove_b = scalar, U08, 851, "%", 1, 0, 0, 100, 0 pwm_onabove_c = scalar, U08, 852, "%", 1, 0, 0, 100, 0 pwm_onabove_d = scalar, U08, 853, "%", 1, 0, 0, 100, 0 pwm_onabove_e = scalar, U08, 854, "%", 1, 0, 0, 100, 0 pwm_onabove_f = scalar, U08, 855, "%", 1, 0, 0, 100, 0 pwm_offbelow_a = scalar, U08, 856, "%", 1, 0, 0, 100, 0 pwm_offbelow_b = scalar, U08, 857, "%", 1, 0, 0, 100, 0 pwm_offbelow_c = scalar, U08, 858, "%", 1, 0, 0, 100, 0 pwm_offbelow_d = scalar, U08, 859, "%", 1, 0, 0, 100, 0 pwm_offbelow_e = scalar, U08, 860, "%", 1, 0, 0, 100, 0 pwm_offbelow_f = scalar, U08, 861, "%", 1, 0, 0, 100, 0 dualfuel_sw_on = bits, U08, 862, [0:0], "Off", "On" dualfuel_sw_fuel = bits,U08, 862, [1:1], "Off", "On" dualfuel_sw_spk = bits, U08, 862, [2:2], "Off", "On" dualfuel_sw_afr = bits, U08, 862, [3:3], "Off", "On" dualfuel_sw_rf = bits, U08, 862, [4:4], "Off", "On" dualfuel_sw_stoich=bits,U08, 862, [5:5], "Off", "On" dualfuel_sw_wue = bits, U08, 862, [6:6], "Off", "On" dualfuel_sw_ase = bits, U08, 862, [7:7], "Off", "On" dualfuel_sw2_prime=bits,U08, 863, [0:0], "Off", "On" dualfuel_sw2_crank=bits,U08, 863, [1:1], "Off", "On" dualfuel_sw2_injp =bits,U08, 863, [2:2], "Off", "On" dualfuel_sw2_smpw =bits,U08, 863, [3:3], "Off", "On" dualfuel_sw2_ob =bits ,U08, 863, [4:4], "Off", "On" dualfuel_sw2_boosw=bits,U08, 863, [5:5], "Off", "On" opentime2_opt1_master = bits, U08, 864, [7:7], "Same", "Individual" opentime2_opt1 = bits, U08, 864, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime2_opt2 = bits, U08, 865, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime2_opt3 = bits, U08, 866, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime2_opt4 = bits, U08, 867, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime2_opt5 = bits, U08, 868, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime2_opt6 = bits, U08, 869, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime2_opt7 = bits, U08, 870, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime2_opt8 = bits, U08, 871, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime2_opta = bits, U08, 872, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime2_opta_pwm= bits, U08, 872, [4:4], "Off", "On" opentime2_optb = bits, U08, 873, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime2_optb_pwm= bits, U08, 873, [4:4], "Off", "On" opentime2_optb_own= bits, U08, 873, [5:5], "Off", "On" opentime2_opt11 = bits, U08, 874, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime2_opt12 = bits, U08, 875, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime2_opt13 = bits, U08, 876, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime2_opt14 = bits, U08, 877, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime2_opt15 = bits, U08, 878, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" opentime2_opt16 = bits, U08, 879, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" ; opentime2_opt17 = bits, U08, 880, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" ; opentime2_opt18 = bits, U08, 881, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw2_opt1_master = bits, U08, 864, [7:7], "Off", "On" smallpw2_opt1 = bits, U08, 882, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw2_opt2 = bits, U08, 883, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw2_opt3 = bits, U08, 884, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw2_opt4 = bits, U08, 885, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw2_opt5 = bits, U08, 886, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw2_opt6 = bits, U08, 887, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw2_opt7 = bits, U08, 888, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw2_opt8 = bits, U08, 889, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw2_opta = bits, U08, 890, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw2_optb = bits, U08, 891, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw2_opt11 = bits, U08, 892, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw2_opt12 = bits, U08, 893, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw2_opt13 = bits, U08, 894, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw2_opt14 = bits, U08, 895, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw2_opt15 = bits, U08, 896, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" smallpw2_opt16 = bits, U08, 897, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" ; smallpw2_opt17 = bits, U08, 898, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" ; smallpw2_opt18 = bits, U08, 899, [0:1], "Curve 1", "Curve 2", "Curve 3", "Curve 4" dualfuel_pin = bits, U08, 900, [0:4], "INVALID", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "INVALID", "INVALID", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" dualfuel_opt_temp= bits, U08, 901, [0:0], "Off", "On" dualfuel_opt_press=bits, U08, 901, [1:1], "Off", "On" dualfuel_opt_mode = bits,U08, 901, [2:2], "Switching", "Dual table" dualfuel_opt_out = bits,U08, 901, [3:3], "Shared outputs+relay", "Different outputs" #if PW_4X inj2Open1 = scalar, U16, 902, "ms", 0.004, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) inj2Open2 = scalar, U16, 904, "ms", 0.004, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) inj2Open3 = scalar, U16, 906, "ms", 0.004, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) inj2Open4 = scalar, U16, 908, "ms", 0.004, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) inj2Open5 = scalar, U16, 910, "ms", 0.004, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) inj2Open6 = scalar, U16, 912, "ms", 0.004, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) inj2Open7 = scalar, U16, 914, "ms", 0.004, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) inj2Open8 = scalar, U16, 916, "ms", 0.004, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) inj2Opena = scalar, U16, 918, "ms", 0.004, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) inj2Openb = scalar, U16, 920, "ms", 0.004, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) ;next 8 not yet used inj2Open11 = scalar, U16, 922, "ms", 0.004, 0.00000, 0.00, 25.50, 3 inj2Open12 = scalar, U16, 924, "ms", 0.004, 0.00000, 0.00, 25.50, 3 inj2Open13 = scalar, U16, 926, "ms", 0.004, 0.00000, 0.00, 25.50, 3 inj2Open14 = scalar, U16, 928, "ms", 0.004, 0.00000, 0.00, 25.50, 3 inj2Open15 = scalar, U16, 930, "ms", 0.004, 0.00000, 0.00, 25.50, 3 inj2Open16 = scalar, U16, 932, "ms", 0.004, 0.00000, 0.00, 25.50, 3 inj2Open17 = scalar, U16, 934, "ms", 0.004, 0.00000, 0.00, 25.50, 3 inj2Open18 = scalar, U16, 936, "ms", 0.004, 0.00000, 0.00, 25.50, 3 #else inj2Open1 = scalar, U16, 902, "ms", 0.001, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) inj2Open2 = scalar, U16, 904, "ms", 0.001, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) inj2Open3 = scalar, U16, 906, "ms", 0.001, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) inj2Open4 = scalar, U16, 908, "ms", 0.001, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) inj2Open5 = scalar, U16, 910, "ms", 0.001, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) inj2Open6 = scalar, U16, 912, "ms", 0.001, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) inj2Open7 = scalar, U16, 914, "ms", 0.001, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) inj2Open8 = scalar, U16, 916, "ms", 0.001, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) inj2Opena = scalar, U16, 918, "ms", 0.001, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) inj2Openb = scalar, U16, 920, "ms", 0.001, 0.00000, 0.00, 25.50, 3 ; * ( 1 byte) ;next 8 not yet used inj2Open11 = scalar, U16, 922, "ms", 0.001, 0.00000, 0.00, 25.50, 3 inj2Open12 = scalar, U16, 924, "ms", 0.001, 0.00000, 0.00, 25.50, 3 inj2Open13 = scalar, U16, 926, "ms", 0.001, 0.00000, 0.00, 25.50, 3 inj2Open14 = scalar, U16, 928, "ms", 0.001, 0.00000, 0.00, 25.50, 3 inj2Open15 = scalar, U16, 930, "ms", 0.001, 0.00000, 0.00, 25.50, 3 inj2Open16 = scalar, U16, 932, "ms", 0.001, 0.00000, 0.00, 25.50, 3 inj2Open17 = scalar, U16, 934, "ms", 0.001, 0.00000, 0.00, 25.50, 3 inj2Open18 = scalar, U16, 936, "ms", 0.001, 0.00000, 0.00, 25.50, 3 #endif inj2PwmT = scalar, U08, 938, "ms", 0.12800, 0.128, 0.00, 32.64, 1 ; * ( 1 byte) inj2PwmPd = scalar, U08, 939, "us", 1.00000, 0.00000, 40.00, 100.00, 0 ; * ( 1 byte) inj2PwmP = scalar, U08, 940, "%", 1.00000, 0.00000, 0.00, 100.00, 0 ; * ( 1 byte) inj2PwmT2 = scalar, U08, 941, "ms", 0.12800, 0.128, 0.00, 32.64, 1 ; * ( 1 byte) inj2PwmPd2 = scalar, U08, 942, "us", 1.00000, 0.00000, 40.00, 100.00, 0 ; * ( 1 byte) inj2PwmP2 = scalar, U08, 943, "%", 1.00000, 0.00000, 0.00, 100.00, 0 ; * ( 1 byte) dualfuel_temp_sens = bits, U08, 944, [0:3], "Off", "Sensor 1", "Sensor 2","Sensor 3","Sensor 4","Sensor 5","Sensor 6","Sensor 7","Sensor 8","Sensor 9","Sensor 10","Sensor 11","Sensor 12","Sensor 13","Sensor 14","Sensor 15" dualfuel_press_sens = bits, U08, 945, [0:3], "Off", "Sensor 1", "Sensor 2","Sensor 3","Sensor 4","Sensor 5","Sensor 6","Sensor 7","Sensor 8","Sensor 9","Sensor 10","Sensor 11","Sensor 12","Sensor 13","Sensor 14","Sensor 15" dualfuel_press_type = bits, U08, 945, [6:7], "Gauge", "Absolute", "Differential", "INVALID" ; Leave these unused variables matching MS2 in case trans controller erroneously adjusts them ; FuelAdj 946 ; SpkAdj, 948 ; IdleAdj, 950 ; SprAdj; 952 pwm_opt_curve_a = bits, U08, 954, [0:0], "Table", "Curve" pwm_opt_curve_b = bits, U08, 954, [1:1], "Table", "Curve" pwm_opt_curve_c = bits, U08, 954, [2:2], "Table", "Curve" pwm_opt_curve_d = bits, U08, 954, [3:3], "Table", "Curve" pwm_opt_curve_e = bits, U08, 954, [4:4], "Table", "Curve" pwm_opt_curve_f = bits, U08, 954, [5:5], "Table", "Curve" ;gap ITB_load_mappoint = scalar, S16, 956, "% baro", 0.1000, 0, 30, 100.0, 1 ITB_load_idletpsthresh = scalar, S16, 958, "%", 0.1000, 0, -10, 100, 0 idle_voltage_comp_voltage = array, S16, 960, [6], "V", 0.1000, 0, 9, 17, 1 idle_voltage_comp_delta = array, S16, 972, [6], "%", 0.392, 0.00000, -20, 20, 1 page = 3 ; 8 boost_ctl_load_targets = array, S16, 0, [8x8], "%", 0.1, 0, 0, {loadhigh}, 1 boost_ctl_loadtarg_tps_bins=array, S16, 128, [8], "%", 0.1, 0, 0, 100, 1 boost_ctl_loadtarg_rpm_bins=array, U16, 144, [8], "rpm", 1, 0, 0, {rpmhigh}, 0 boost_ctl_pwm_targets = array, U08, 160, [8x8], "%", 1, 0, 0, 100, 0 boost_ctl_pwmtarg_tps_bins=array, S16, 224, [8], "%", 0.1, 0, 0, 100, 1 boost_ctl_pwmtarg_rpm_bins=array, U16, 240, [8], "rpm", 1, 0, 0, {rpmhigh}, 0 #if PW_4X primePWTable = array, S16, 256, [ 10], "ms", 0.40000, 0.00000, 0.00, 260.00, 1 ; * ( 20 bytes) #else primePWTable = array, S16, 256, [ 10], "ms", 0.10000, 0.00000, 0.00, 65.00, 1 ; * ( 20 bytes) #endif crankPctTable =array, U16, 276, [ 10], "%", 1, 1, 1, 10000, 0 ; * ( 20 bytes) asePctTable =array, S16, 296, [ 10], "%", 1.00000, 0.00000, 0.00, 400.00, 0 ; * ( 2 bytes) aseCntTable =array, S16, 316, [ 10], "cycles", 1.00000, 0.00000, 0.00, 2500.00, 0 ; * ( 2 bytes) #if CELSIUS matTemps =array, S16, 336, [ 6], "°C", 0.05555, -320.000,-40.00, 150.00, 1 ; * ( 12 bytes) #else matTemps =array, S16, 336, [ 6], "°F", 0.10000, 0.00000,-40.00, 300.00, 1 #endif matRetard =array, U08, 348, [ 6], "deg", 0.10000, 0.00000, 0.00, 25.5, 1 ; * ( 6 bytes) EAEAWCRPMbins = array, U16, 354, [ 12], "rpm", 1.00000, 0.00000,0, {rpmhigh}, 0 ; * (24 bytes) EAESOCRPMbins = array, U16, 378, [ 12], "rpm", 1.00000, 0.00000,0, {rpmhigh}, 0 ; * (24 bytes) EAEAWCKPAbins = array, U16, 402, [ 12], { bitStringValue( algorithmUnits , (eaeload ? eaeload : algorithm) ) }, 0.10000, 0.00000,0, {loadhigh}, 0 ; * (24 bytes) EAESOCKPAbins = array, U16, 426, [ 12], { bitStringValue( algorithmUnits , (eaeload ? eaeload : algorithm) ) }, 0.10000, 0.00000,0, {loadhigh}, 0 ; * (24 bytes) EAEBAWC = array, U08, 450, [ 12], "%", 1.00000, 0.00000,0, 100, 0 ; * (12 bytes) EAEBSOC = array, U08, 462, [ 12], "%", 0.10000, 0.00000,0, 25.5, 1 ; * (12 bytes) EAEAWN = array, U08, 474, [ 12], "%", 1.00000, 0.00000,0, 200, 0 ; * (12 bytes) EAESON = array, U08, 486, [ 12], "%", 1.00000, 0.00000,0, 200, 0 ; * (12 bytes) EAEAWW = array, U08, 498, [ 12], "%", 1.00000, 0.00000,0, 200, 0 EAESOW = array, U08, 510, [ 12], "%", 1.00000, 0.00000,0, 200, 0 ; Supplemental corrections for barometer and MAT. baroCorrVals = array , S16, 522, [ 9], "kPa", 0.10000, 0.00000, 0.00, 110.00, 1 ; * ( 24 bytes) #if CELSIUS matCorrTemps2 = array , S16, 540, [ 9], "°C", 0.05555, -320.000,-40.00, 150.00, 1 ; * ( 12 bytes) #else matCorrTemps2 = array , S16, 540, [ 9], "°F", 0.10000, 0.00000,-40.00, 300.00, 1 #endif #if CELSIUS temp_table_p5 = array, S16, 558, [ 10], "°C", 0.05555, -320.000, -40.00, {clthighlim}, 0 #else temp_table_p5 = array, S16, 558, [ 10], "°F", 0.10000, 0.000,-40.00, {clthighlim}, 1 #endif #if CELSIUS EAEAWWCLTbins = array, S16, 578, [ 12], "deg", 0.05555, -320.000, -40.00, {clthighlim}, 0 EAESOWCLTbins = array, S16, 602, [ 12], "deg", 0.05555, -320.000, -40.00, {clthighlim}, 0 #else EAEAWWCLTbins = array, S16, 578, [ 12], "deg", 0.10000, 0.000,-40.00, {clthighlim}, 1 EAESOWCLTbins = array, S16, 602, [ 12], "deg", 0.10000, 0.000,-40.00, {clthighlim}, 1 #endif pwmidle_target_rpms = array, U16, 626, [ 8 ], "rpms", 1, 0.00000, 0.00, 2000, 0; #if CELSIUS pwmidle_clt_temps = array, S16, 642, [8], "°C", 0.05555, -320.000,-40.00, {clthighlim}, 1 ; #else pwmidle_clt_temps = array, S16, 642, [8], "°F", 0.10000, 0.00000,-40.00, {clthighlim}, 1 #endif ;padding 20 #if CELSIUS RevLimLookup = array , S16, 678, [ 8], "°C", 0.05555, -320.000,-40.00, {clthighlim}, 1 ; * ( 16 bytes) #else RevLimLookup = array , S16, 678, [ 8], "°F", 0.10000, 0.00000,-40.00, {clthighlim}, 1 ; * ( 16 bytes) #endif RevLimRpm1 = array , U16, 694, [ 8], "RPM", 1.00000, 0.00000, 0.00,{rpmhigh}, 0 ; * ( 16 bytes ;these are not presently used, but might re-appear Xknk_rpm = array , U16, 710, [ 6], "rpm", 1.0, 0.0, 0.0, {rpmhigh}, 0 ; * ( 2 bytes) Xknk_thresh = array , U16, 722, [ 6], "v", 0.01, 0.0, 0.0, 5.00, 2 ; * ( 2 bytes) RotarySplitTable = array, S16, 734, [8x8], "deg", 0.10000, 0.00000, -60, 20, 1 RotarySplitLoad = array, U16, 862, [ 8 ], { bitStringValue( algorithmUnits , IgnAlgorithm ) }, 0.10000, 0.00000, 0, {loadhigh}, 0 RotarySplitRPM = array, U16, 878, [ 8 ], "RPM", 1, 0.00000, 0, {rpmhigh}, 0 NoiseFilterRpm = array, U16, 894, [ 4], "RPM", 1, 0.00000, 0.00, {rpmhigh}, 0 NoiseFilterLen = array, U16, 902, [ 4], "usec", 1.0, 0.00000, 0.00, 43000, 1 VariableLagTPSBins = array, U08, 910, [4], "%/sec", 1, 0.000000, 0.00, 255.00, 0 VariableLagMapLags = array, U08, 914, [4], "Lag", 1, 0.000000, 0.00, 255.00, 0 pwmidle_crank_dutyorsteps_duty = array, U16, 918, [4], "%", 0.392, 0.00000, 0, 100, 1 pwmidle_crank_dutyorsteps_steps = array, U16, 918, [4], "steps", 1, 0, 0, 512, 0 #if CELSIUS pwmidle_crank_clt_temps = array, S16, 926, [4], "°C", 0.05555, -320.000,-40.00, {clthighlim}, 1 #else pwmidle_crank_clt_temps = array, S16, 926, [4], "°F", 0.10000, 0.00000,-40.00, {clthighlim}, 1 #endif matclt_pct = array, U16, 934, [6], "%", 0.010, 0, 0, 100, 1 matclt_flow = array, U16, 946, [6], "load*rpm", 100, 0, 0, 6553500, 0 ;user defined ; these are not used by the code and are provided for users to use and learn from ; if you want to add more... you also have to make matching changes in ms2_extra.h ; and ms2_extra_main.c ; note that it you add an 'int' that two bytes are consumed and two of the following ; spare array will need to be removed! user_value1 = scalar, U16, 958, "", 1, 0, 0, 65535, 0 user_value2 = scalar, U16, 960, "", 1, 0, 0, 65535, 0 user_conf0 = bits, U08, 962, [0:0], "Off", "On" user_conf1 = bits, U08, 962, [1:2], "Mode 0", "Mode 1", "Mode 2", "Mode 3" ;spare 10 bytes ;end user defined ;pad1 baroCorrDelta = array , S16, 974, [ 9], "%", 0.10000, 0.00000,-120.0, 120.0, 1 ; * ( 6 bytes) matCorrDelta2 = array , S16, 992, [ 9], "%", 0.10000, 0.00000,-120.0, 150.0, 1 ; * ( 6 bytes) ; space page = 4 ; 9 - injector channel trims inj_trima = array , S08, 000, [6x6], "%", 0.20000, 0.00000, -25.4, 25.4, 1 ; * (36 bytes) inj_trimb = array , S08, 036, [6x6], "%", 0.20000, 0.00000, -25.4, 25.4, 1 ; * (36 bytes) inj_trimc = array , S08, 072, [6x6], "%", 0.20000, 0.00000, -25.4, 25.4, 1 ; * (36 bytes) inj_trimd = array , S08, 108, [6x6], "%", 0.20000, 0.00000, -25.4, 25.4, 1 ; * (36 bytes) inj_trime = array , S08, 144, [6x6], "%", 0.20000, 0.00000, -25.4, 25.4, 1 ; * (36 bytes) inj_trimf = array , S08, 180, [6x6], "%", 0.20000, 0.00000, -25.4, 25.4, 1 ; * (36 bytes) inj_trimg = array , S08, 216, [6x6], "%", 0.20000, 0.00000, -25.4, 25.4, 1 ; * (36 bytes) inj_trimh = array , S08, 252, [6x6], "%", 0.20000, 0.00000, -25.4, 25.4, 1 ; * (36 bytes) inj_trimi = array , S08, 288, [6x6], "%", 0.20000, 0.00000, -25.4, 25.4, 1 ; * (36 bytes) inj_trimj = array , S08, 324, [6x6], "%", 0.20000, 0.00000, -25.4, 25.4, 1 ; * (36 bytes) inj_trimk = array , S08, 360, [6x6], "%", 0.20000, 0.00000, -25.4, 25.4, 1 ; * (36 bytes) inj_triml = array , S08, 396, [6x6], "%", 0.20000, 0.00000, -25.4, 25.4, 1 ; * (36 bytes) inj_trimm = array , S08, 432, [6x6], "%", 0.20000, 0.00000, -25.4, 25.4, 1 ; * (36 bytes) inj_trimn = array , S08, 468, [6x6], "%", 0.20000, 0.00000, -25.4, 25.4, 1 ; * (36 bytes) inj_trimo = array , S08, 504, [6x6], "%", 0.20000, 0.00000, -25.4, 25.4, 1 ; * (36 bytes) inj_trimp = array , S08, 540, [6x6], "%", 0.20000, 0.00000, -25.4, 25.4, 1 ; * (36 bytes) inj_trim_rpm = array, U16, 576, [6], "rpm", 1, 0.00000, 0, {rpmhigh}, 0 ; * (12 bytes) inj_trim_load =array, U16, 588, [6], { bitStringValue( algorithmUnits , algorithm ) }, 0.1, 0.0000, 0, {loadhigh}, 1 inj_timing = array, S16, 600, [12x12], "deg", 0.10000, 0.00000, -360.0, 720.0, 1 inj_timing_rpm = array, U16, 888, [12], "rpm", 1, 0, 0, {rpmhigh}, 0 inj_timing_load = array, S16, 912, [12], "%", 0.10000, 0, 0, {loadhigh}, 1 maxafr1_load = array, U16, 936, [6], "%", 0.10000, 0, 0, {loadhigh}, 1 maxafr1_rpm = array, U16, 948, [6], "rpm", 1, 0, 0, {rpmhigh}, 0 #if LAMBDA maxafr1_diff = array, U08, 960, [6x6], "Lambda", 0.006803, 0.00000, 0.00, 0.14, 3 #else maxafr1_diff = array, U08, 960, [6x6], "AFR", 0.10000, 0.00000, 0.00, 2.00, 1 #endif dwellrpm_dwell = array, U08, 996, [6], "ms", 0.1, 0, 1, 8, 1 dwellrpm_rpm = array, U16, 1002, [6], "RPM", 1, 0, 0, 15000, 0 page = 5 ; 10 boost_ctl_load_targets2 = array, S16, 0, [8x8], "%", 0.1, 0, 0, {loadhigh}, 1 boost_ctl_loadtarg_tps_bins2=array, S16, 128, [8], "%", 0.1, 0, 0, 100, 1 boost_ctl_loadtarg_rpm_bins2=array, U16, 144, [8], "rpm", 1, 0, 0, {rpmhigh}, 0 boost_ctl_pwm_targets2 = array, U08, 160, [8x8], "%", 1, 0, 0, 100, 0 boost_ctl_pwmtarg_tps_bins2=array, S16, 224, [8], "%", 0.1, 0, 0, 100, 1 boost_ctl_pwmtarg_rpm_bins2=array, U16, 240, [8], "rpm", 1, 0, 0, {rpmhigh}, 0 boost_timed_pct = array, U08, 256, [ 6 ], "%", 1, 0, 0, 100, 0 boost_timed_time= array, U16, 262, [ 6 ], "s", 0.001, 0, 0, 15, 1 boostvss_duty = array, U08, 274, [ 6 ], "%", 1, 0, 0, 100, 0 boostvss_target = array, U16, 280, [ 6 ], "kPa", 0.1, 0, 0, {loadhigh}, 1 boostvss_speed = array, U16, 292, [ 6 ], { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, { msToPrefUnitsScale }, 0, 0, 1000, 0 map_sample_rpms = array, U16, 304, [ 8 ], "rpm", 1, 0, 0, {rpmhigh}, 0 map_sample_timing = array, S16, 320, [ 8 ], "deg", 0.10000, 0, -360, 720, 1 #if LAMBDA afrTable1 = array , U08, 336, [12x12], "Lambda", 0.006803, 0.00000, 0.00, 2.00, 3 ; * (144 bytes) afrTable2 = array , U08, 480, [12x12], "Lambda", 0.006803, 0.00000, 0.00, 2.00, 3 ; * (144 bytes) #else afrTable1 = array , U08, 336, [12x12], "AFR", 0.10000, 0.00000, 1.00, 25.00, 1 afrTable2 = array , U08, 480, [12x12], "AFR", 0.10000, 0.00000, 1.00, 25.00, 1 #endif wueBins = array , U08, 624, [ 10], "%", 1.00000, 0.00000, { wue_lpg?50:100 }, 255.00, 0 ; * ( 10 bytes) ;gap 8 bytes iacstepTable = array , S16, 642, [ 10], "steps", 1.00000, 0.00000, 0.00, 500.00, 0 ; * ( 20 bytes) arpm_table1 = array , U16, 662, [ 12], "RPM", 1.00000, 0.00000, 0.00,{rpmhigh}, 0 ; * ( 24 bytes) arpm_table2 = array , U16, 686, [ 12], "RPM", 1.00000, 0.00000, 0.00,{rpmhigh}, 0 ; * ( 24 bytes) amap_table1 = array , S16, 710, [ 12], { bitStringValue( algorithmUnits , (afrload ? afrload : algorithm) ) }, 0.10000, 0.00000, 0.00, {loadhigh}, 1 ; * ( 24 bytes) amap_table2 = array , S16, 734, [ 12], { bitStringValue( algorithmUnits , (afrload ? afrload : algorithm) ) }, 0.10000, 0.00000, 0.00, {loadhigh}, 1 ; * ( 24 bytes) #if CELSIUS tempTable = array , S16, 758, [ 10], "°C", 0.05555, -320.000,-40.00, {clthighlim}, 1 ; * ( 20 bytes) Temperature bins for cranking, cold AE and WUE ; temp_table #else tempTable = array , S16, 758, [ 10], "°F", 0.10000, 0.00000,-40.00, {clthighlim}, 1 #endif ;gap dwellvolts = array , U08, 794, [ 6], "V", 0.10000, 0.00000,6, 18, 1 ; * ( 6 bytes) dwellcorr = array , U08, 800, [ 6], "%", 2, 0.00000,20, 512, 0 ; * ( 6 bytes) cold_adv_table = array , S16, 806, [ 10], "deg", 0.10000, 0.00000,-10.00, 10.00, 1 ; * ( 20 bytes) ipwmTable = array , S16, 826, [ 10], "%", 0.392, 0.00000, 0.00, 100.00, 1 ;846 opentimepct0 = array, U16, 846, [ 6], "%", 0.1, 0.00000, 0.00, 500, 1 opentimepct1 = array, U16, 858, [ 6], "%", 0.1, 0.00000, 0.00, 500, 1 opentimepct2 = array, U16, 870, [ 6], "%", 0.1, 0.00000, 0.00, 500, 1 opentimepct3 = array, U16, 882, [ 6], "%", 0.1, 0.00000, 0.00, 500, 1 opentimev = array, U16, 894, [ 6], "V", 0.100, 0.00000, 6, 19.2, 1 #if PW_4X smallpw0 = array, U16, 906, [ 6], "ms", 0.004, 0.00000, 0.00, 2, 3 smallpw1 = array, U16, 918, [ 6], "ms", 0.004, 0.00000, 0.00, 2, 3 smallpw2 = array, U16, 930, [ 6], "ms", 0.004, 0.00000, 0.00, 2, 3 smallpw3 = array, U16, 942, [ 6], "ms", 0.004, 0.00000, 0.00, 2, 3 smallpwpw = array, U16, 954, [ 6], "ms", 0.004, 0.00000, 0.00, 2, 3 #else smallpw0 = array, U16, 906, [ 6], "ms", 0.001, 0.00000, 0.00, 2, 3 smallpw1 = array, U16, 918, [ 6], "ms", 0.001, 0.00000, 0.00, 2, 3 smallpw2 = array, U16, 930, [ 6], "ms", 0.001, 0.00000, 0.00, 2, 3 smallpw3 = array, U16, 942, [ 6], "ms", 0.001, 0.00000, 0.00, 2, 3 smallpwpw = array, U16, 954, [ 6], "ms", 0.001, 0.00000, 0.00, 2, 3 #endif waterinj_rpm = array, U16, 966, [ 8], "RPM", 1, 0.00000, 0.00, {rpmhigh}, 0 waterinj_map = array, U16, 982, [ 4], "kPa", 0.1, 0.00000, 0.00, {loadhigh}, 0 waterinj_duty = array, U08, 990, [8 x 4], "%", 1, 0, 0, 100, 0 page = 6 ; 11 - spark channel trims spk_trima = array , S08, 000, [6x6], "%", 0.10000, 0.00000, -12.7, 12.7, 1 ; * (36 bytes) spk_trimb = array , S08, 036, [6x6], "%", 0.10000, 0.00000, -12.7, 12.7, 1 ; * (36 bytes) spk_trimc = array , S08, 072, [6x6], "%", 0.10000, 0.00000, -12.7, 12.7, 1 ; * (36 bytes) spk_trimd = array , S08, 108, [6x6], "%", 0.10000, 0.00000, -12.7, 12.7, 1 ; * (36 bytes) spk_trime = array , S08, 144, [6x6], "%", 0.10000, 0.00000, -12.7, 12.7, 1 ; * (36 bytes) spk_trimf = array , S08, 180, [6x6], "%", 0.10000, 0.00000, -12.7, 12.7, 1 ; * (36 bytes) spk_trimg = array , S08, 216, [6x6], "%", 0.10000, 0.00000, -12.7, 12.7, 1 ; * (36 bytes) spk_trimh = array , S08, 252, [6x6], "%", 0.10000, 0.00000, -12.7, 12.7, 1 ; * (36 bytes) spk_trimi = array , S08, 288, [6x6], "%", 0.10000, 0.00000, -12.7, 12.7, 1 ; * (36 bytes) spk_trimj = array , S08, 324, [6x6], "%", 0.10000, 0.00000, -12.7, 12.7, 1 ; * (36 bytes) spk_trimk = array , S08, 360, [6x6], "%", 0.10000, 0.00000, -12.7, 12.7, 1 ; * (36 bytes) spk_triml = array , S08, 396, [6x6], "%", 0.10000, 0.00000, -12.7, 12.7, 1 ; * (36 bytes) spk_trimm = array , S08, 432, [6x6], "%", 0.10000, 0.00000, -12.7, 12.7, 1 ; * (36 bytes) spk_trimn = array , S08, 468, [6x6], "%", 0.10000, 0.00000, -12.7, 12.7, 1 ; * (36 bytes) spk_trimo = array , S08, 504, [6x6], "%", 0.10000, 0.00000, -12.7, 12.7, 1 ; * (36 bytes) spk_trimp = array , S08, 540, [6x6], "%", 0.10000, 0.00000, -12.7, 12.7, 1 ; * (36 bytes) spk_trim_rpm = array, U16, 576, [6], "rpm", 1, 0.00000, 0, {rpmhigh}, 0 ; * (12 bytes) spk_trim_load = array, U16, 588, [6], { bitStringValue( algorithmUnits , IgnAlgorithm ) }, 0.1, 0.0000, 0, {loadhigh}, 1 ; * (12 bytes) XAcc =array, U16, 600, [5], "%", 0.10000, 0.00000, 5.00, 90, 1 ; * ( 10 bytes) TauAcc =array, U16, 610, [5], "ms",1.00000, 0.00000, 2.00, 20000, 0 ; * ( 10 bytes) XDec =array, U16, 620, [5], "%", 0.10000, 0.00000, 5.00, 90, 1 ; * ( 10 bytes) TauDec =array, U16, 630, [5], "ms",1.00000, 0.00000, 2.00, 20000, 0 ; * ( 10 bytes) XTrpms =array, U16, 640, [5], "rpm",1.00000, 0.00000, 0.00, {rpmhigh}, 0 ; * ( 10 bytes) XClt =array, U16, 650, [10], "%", 1.00000, 0.00000, 0.00, 600, 0 ; * ( 20 bytes) TauClt =array, U16, 670, [10], "%", 1.00000, 0.00000, 0.00, 600, 0 ; * ( 20 bytes) #if CELSIUS XClt_temps = array, S16, 690, [ 10], "°C", 0.05555, -320.000, -40.00, {clthighlim}, 0 TauClt_temps = array, S16, 710, [ 10], "°C", 0.05555, -320.000, -40.00, {clthighlim}, 0 #else XClt_temps = array, S16, 690, [ 10], "°F", 0.10000, 0.000,-40.00, {clthighlim}, 1 TauClt_temps = array, S16, 710, [ 10], "°F", 0.10000, 0.000,-40.00, {clthighlim}, 1 #endif ;progressive nitrous tables n2o1_time = array, U16, 730, [6], "s", 0.001, 0, 0, 15, 2 n2o1_rpm = array, U16, 742, [6], "RPM", 1, 0, 0, {rpmhigh}, 0 n2o1_duty = array, U08, 754, [6], "%", 1, 0, 0, 100, 1 #if PW_4X n2o1_pw = array, S16, 760, [6], "ms", 0.004, 0, -20, 80, 3 n2o2_pw = array, S16, 814, [6], "ms", 0.004, 0, -20, 80, 3 #else n2o1_pw = array, S16, 760, [6], "ms", 0.001, 0, -5, 20, 3 n2o2_pw = array, S16, 814, [6], "ms", 0.001, 0, -5, 20, 3 #endif n2o1_retard = array, U16, 772, [6], "deg", 0.1, 0, 0, 30, 1 n2o2_time = array, U16, 784, [6], "s", 0.001, 0, 0, 15, 2 n2o2_rpm = array, U16, 796, [6], "RPM", 1, 0, 0, {rpmhigh}, 0 n2o2_duty = array, U08, 808, [6], "%", 1, 0, 0, 100, 1 ; n2o2_pw = array, S16, 814, [6], "ms", 0.001, 0, -5, 20, 3 n2o2_retard = array, U16, 826, [6], "deg", 0.1, 0, 0, 30, 1 ; staged tables staged_percents=array, U08, 838, [8x8], "%", 1, 0, 0, 100, 0 staged_rpms = array, U16, 902, [8], "rpm", 1, 0, 0, {rpmhigh}, 0 staged_loads = array, S16, 918, [8], "%", 0.1, 0, 0, 250, 1 MAFFlow = array, U16, 934, [12], "g/sec", {0.01 * (maf_range + 1)}, 0.00000, 0.00, {655 * (maf_range + 1)}, 1 MAFCor = array, U08, 958, [12], "%", 1.00000, 0.00000, 0.00, 255.0, 0 launch_time = array, U16, 970, [6], "s", 0.001, 0, 0, 15, 2 launch_retard = array, U16, 982, [6], "deg", 0.1, 0, 0, 30, 1 cranktaper_time=array, U16, 994, [6], "s", 0.1, 0, 0, 15, 1 cranktaper_timeevents=array,U16, 994, [6], "events", 1, 0, 0, 1000, 0 ; same again, different units cranktaper_pct =array, U16, 1006, [6], "%", 0.1, 0, 0, 500, 0 page = 7 ; 12 veTable1 = array , U16, 000, [16x16], "%", 0.10000, 0.00000, 0.00, {vehigh}, 1 ; * (512 bytes) veTable2 = array , U16, 512, [16x16], "%", 0.10000, 0.00000, 0.00, {vehigh}, 1 ; page = 8 ; 13 advanceTable1 = array , S16, 000, [16x16], "deg", 0.10000, 0.00000,-10.00, 90.00, 1 ; * (512 bytes) advanceTable2 = array , S16, 512, [16x16], "deg", 0.10000, 0.00000,-10.00, 90.00, 1 ; * (512 bytes) page = 9 ; 18 veTable3 = array , U16, 000, [16x16], "%", 0.10000, 0.00000, 0.00, {vehigh}, 1 ; advanceTable3 = array , S16, 512, [16x16], "deg", 0.10000, 0.00000,-10.00, 90.00, 1 ; * (288 bytes) page = 10 ; 19 frpm_table1 = array , U16, 000, [ 16], "RPM", 1.00000, 0.00000, 0.00,{rpmhigh}, 0 ; * ( 24 bytes) frpm_table2 = array , U16, 032, [ 16], "RPM", 1.00000, 0.00000, 0.00,{rpmhigh}, 0 ; * ( 24 bytes) frpm_table3 = array , U16, 064, [ 16], "RPM", 1.00000, 0.00000, 0.00,{rpmhigh}, 0 ; * ( 24 bytes) fmap_table1 = array , S16, 096, [ 16], { bitStringValue( algorithmUnits , algorithm ) }, 0.10000, 0.00000, 0.00, {loadhigh}, 1 ; * ( 24 bytes) fmap_table2 = array , S16, 128, [ 16], { bitStringValue( algorithmUnits , algorithm2 ) }, 0.10000, 0.00000, 0.00, {loadhigh}, 1 ; * ( 24 bytes) fmap_table3 = array , S16, 160, [ 16], { bitStringValue( algorithmUnits , algorithm ) }, 0.10000, 0.00000, 0.00, {loadhigh}, 1 ; * ( 24 bytes) srpm_table1 = array , U16, 192, [ 16], "RPM", 1.00000, 0.00000, 0.00,{rpmhigh}, 0 ; * ( 24 bytes) srpm_table2 = array , U16, 224, [ 16], "RPM", 1.00000, 0.00000, 0.00,{rpmhigh}, 0 ; * ( 24 bytes) srpm_table3 = array , U16, 256, [ 16], "RPM", 1.00000, 0.00000, 0.00,{rpmhigh}, 0 ; * ( 24 bytes) smap_table1 = array , S16, 288, [ 16], { bitStringValue( algorithmUnits , IgnAlgorithm ) }, 0.10000, 0.00000, 0.00, {loadhigh}, 1 ; * ( 24 bytes) smap_table2 = array , S16, 320, [ 16], { bitStringValue( algorithmUnits , IgnAlgorithm2 ) }, 0.10000, 0.00000, 0.00, {loadhigh}, 1 ; * ( 24 bytes) smap_table3 = array , S16, 352, [ 16], { bitStringValue( algorithmUnits , IgnAlgorithm ) }, 0.10000, 0.00000, 0.00, {loadhigh}, 1 ; * ( 24 bytes) EAEAWCRPMbins2 = array, U16, 384, [ 12], "rpm", 1.0000, 0.00000, 0.00, {rpmhigh}, 0 ; * ( 24 bytes) EAESOCRPMbins2 = array, U16, 408, [ 12], "rpm", 1.0000, 0.00000, 0.00, {rpmhigh}, 0 ; * ( 24 bytes) EAEAWCKPAbins2 = array, U16, 432, [ 12], { bitStringValue( algorithmUnits , (eaeload ? eaeload : algorithm) ) }, 0.1000, 0.00000, 0.00, {loadhigh}, 1 EAESOCKPAbins2 = array, U16, 456, [ 12], { bitStringValue( algorithmUnits , (eaeload ? eaeload : algorithm) ) }, 0.1000, 0.00000, 0.00, {loadhigh}, 1 EAEBAWC2 = array, U08, 480, [ 12], "%", 1.0000, 0.00000, 0.00, 100.00, 0 EAEBSOC2 = array, U08, 492, [ 12], "%", 0.10000, 0.00000, 0.00, 25.5, 1 EAEAWN2 = array, U08, 504, [ 12], "%", 1.00000, 0.00000,0, 200, 0 ; * (12 bytes) EAESON2 = array, U08, 516, [ 12], "%", 1.00000, 0.00000,0, 200, 0 EAEAWW2 = array, U08, 528, [ 12], "%", 1.0000, 0.00000, 0.00, 100, 0 EAESOW2 = array, U08, 540, [ 12], "%", 1.0000, 0.00000, 0.00, 100, 0 #if CELSIUS EAEAWWCLTbins2 = array, S16, 552, [ 12], "deg", 0.05555, -320.000, -40.00, {clthighlim}, 0 EAESOWCLTbins2 = array, S16, 576, [ 12], "deg", 0.05555, -320.000, -40.00, {clthighlim}, 0 #else EAEAWWCLTbins2 = array, S16, 552, [ 12], "deg", 0.10000, 0.000,-40.00, {clthighlim}, 1 EAESOWCLTbins2 = array, S16, 576, [ 12], "deg", 0.10000, 0.000,-40.00, {clthighlim}, 1 #endif ITB_load_loadvals= array, S16, 600, [ 12], "%", 0.10000, 0.000, 0, 100.00, 1 ITB_load_switchpoints = array,S16, 624, [ 12], "%", 0.10000, 0.000, 0, 100.00, 1 ITB_load_rpms = array, U16, 648, [ 12], "rpm", 1.0000, 0.000, 0, {rpmhigh}, 0 idleve_table1 = array, U16, 672, [4x4], "%", 0.10000, 0.000, 0, 200, 1 idleve_table2 = array, U16, 704, [4x4], "%", 0.10000, 0.000, 0, 200, 1 idleve_loads1 = array, S16, 736, [4 ], "%", 0.10000, 0.000, 0, 255, 1 idleve_loads2 = array, S16, 744, [4 ], "%", 0.10000, 0.000, 0, 255, 1 idleve_rpms1 = array, U16, 752, [4 ], "rpm", 1.00000, 0.000, 0, {rpmhigh}, 0 idleve_rpms2 = array, U16, 760, [4 ], "rpm", 1.00000, 0.000, 0, {rpmhigh}, 0 ;TC tc_perfect_vss = array, U16, 768, [ 10 ], { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, { msToPrefUnitsScale }, 0.00000, 0, 200, 1 tc_perfect_time = array, U16, 788, [ 10 ], "s", 0.001024, 0.00000, 0, 30, 1 tc_react_x = array, U16, 808, [ 4 ], "slip% x 0.01s", 0.1, 0.00000, 0, 10000, 1 tc_retard = array, U16, 816, [ 4 ], "deg", 0.1, 0.00000, 0, 30, 1 tc_spkcut = array, U08, 824, [ 4 ], "cut%", 1, 0.00000, 0, 100, 0 tc_addfuel = array, U08, 828, [ 4 ], "add%", 1, 0.00000, 0, 100, 1 tc_nitrous = array, U08, 832, [ 4 ], "cut%", 1, 0.00000, 0, 100, 1 tc_boost = array, U08, 836, [ 4 ], "cut%", 1, 0.00000, 0, 100, 1 ;840 knock_rpms = array, U16, 840, [10], "rpm", 1, 0, 0, {rpmhigh}, 0 knock_thresholds= array, U16, 860, [10], "%", 0.1, 0, 0, 100, 1 knock_starts= array, S16, 880, [10], "deg", 0.1, 0, -50, 50, 1 knock_durations = array, S16, 900, [10], "deg", 0.1, 0, 0, 50, 1 ;920 pwmidle_cl_initialvalue_rpms = array, U16, 920, [5], "rpm", 1, 0, 0, {rpmhigh}, 0 #if CELSIUS pwmidle_cl_initialvalue_matorclt = array, S16, 930, [5], "°C", 0.05555, -320, -40, 230, 0 #else pwmidle_cl_initialvalue_matorclt = array, S16, 930, [5], "°F", 0.10000, 0.000, -40, 450, 0 #endif pwmidle_cl_initialvalues_duties = array, U08, 940, [5 x 5], "%", 0.392, 0.00000, 0, 100, 1 pwmidle_cl_initialvalues_steps = array, U08, 940, [5 x 5], "steps", 1, 0, 0, 255, 0 ;pad #if CELSIUS knock_clts = array, S16, 966, [ 4], "°C", 0.05555, -320.000, -40.00, {clthighlim}, 0 #else knock_clts = array, S16, 966, [ 4], "°F", 0.10000, 0.000,-40.00, {clthighlim}, 1 #endif knock_upscale = array, U16, 974, [4], "%", 0.1, 0, 100, 600, 1 tc_perfect_rpm = array, U16, 982, [ 10 ], "rpm", 1.0000, 0.00000, 0, {rpmhigh}, 0 tc_boost_duty_delta = array, S08, 1002, [ 4 ], "+/-duty", 1, 0.00000, -100, 100, 0 page = 11 ; 21 pwm_rpms_a = array, S16, 0, [6], "rpm",{ pwm_opt_curve_a == 0 ? 1 : getChannelScaleByOffset(pwm_opt_load_a_offset) } , { pwm_opt_curve_a == 0 ? 0 : getChannelTranslateByOffset(pwm_opt_load_a_offset) }, { pwm_opt_curve_a == 0 ? 0 : getChannelMinByOffset(pwm_opt_load_a_offset) }, { pwm_opt_curve_a == 0 ? rpmhigh : getChannelMaxByOffset(pwm_opt_load_a_offset) }, { pwm_opt_curve_a == 0 ? 0 : getChannelDigitsByOffset(pwm_opt_load_a_offset) } pwm_loadvals_a = array, S16, 12, [6], "%", { getChannelScaleByOffset(pwm_opt_load_a_offset) } , { getChannelTranslateByOffset(pwm_opt_load_a_offset) }, { getChannelMinByOffset(pwm_opt_load_a_offset) }, { getChannelMaxByOffset(pwm_opt_load_a_offset) }, { getChannelDigitsByOffset(pwm_opt_load_a_offset) } pwm_xaxis_a = array, S16, 0, [12], "", { getChannelScaleByOffset(pwm_opt_load_a_offset) } , { getChannelTranslateByOffset(pwm_opt_load_a_offset) }, { getChannelMinByOffset(pwm_opt_load_a_offset) }, { getChannelMaxByOffset(pwm_opt_load_a_offset) }, { getChannelDigitsByOffset(pwm_opt_load_a_offset) } pwm_rpms_b = array, S16, 24, [6], "rpm",{ pwm_opt_curve_b == 0 ? 1 : getChannelScaleByOffset(pwm_opt_load_b_offset) } , { pwm_opt_curve_b == 0 ? 0 : getChannelTranslateByOffset(pwm_opt_load_b_offset) }, { pwm_opt_curve_b == 0 ? 0 : getChannelMinByOffset(pwm_opt_load_b_offset) }, { pwm_opt_curve_b == 0 ? rpmhigh : getChannelMaxByOffset(pwm_opt_load_b_offset) }, { pwm_opt_curve_b == 0 ? 0 : getChannelDigitsByOffset(pwm_opt_load_b_offset) } pwm_loadvals_b = array, S16, 36, [6], "%", { getChannelScaleByOffset(pwm_opt_load_b_offset) } , { getChannelTranslateByOffset(pwm_opt_load_b_offset) }, { getChannelMinByOffset(pwm_opt_load_b_offset) }, { getChannelMaxByOffset(pwm_opt_load_b_offset) }, { getChannelDigitsByOffset(pwm_opt_load_b_offset) } pwm_xaxis_b = array, S16, 24, [12], "", { getChannelScaleByOffset(pwm_opt_load_b_offset) } , { getChannelTranslateByOffset(pwm_opt_load_b_offset) }, { getChannelMinByOffset(pwm_opt_load_b_offset) }, { getChannelMaxByOffset(pwm_opt_load_b_offset) }, { getChannelDigitsByOffset(pwm_opt_load_b_offset) } pwm_rpms_c = array, S16, 48, [6], "rpm",{ pwm_opt_curve_c == 0 ? 1 : getChannelScaleByOffset(pwm_opt_load_c_offset) } , { pwm_opt_curve_c == 0 ? 0 : getChannelTranslateByOffset(pwm_opt_load_c_offset) }, { pwm_opt_curve_c == 0 ? 0 : getChannelMinByOffset(pwm_opt_load_c_offset) }, { pwm_opt_curve_c == 0 ? rpmhigh : getChannelMaxByOffset(pwm_opt_load_c_offset) }, { pwm_opt_curve_c == 0 ? 0 : getChannelDigitsByOffset(pwm_opt_load_c_offset) } pwm_loadvals_c = array, S16, 60, [6], "%", { getChannelScaleByOffset(pwm_opt_load_c_offset) } , { getChannelTranslateByOffset(pwm_opt_load_c_offset) }, { getChannelMinByOffset(pwm_opt_load_c_offset) }, { getChannelMaxByOffset(pwm_opt_load_c_offset) }, { getChannelDigitsByOffset(pwm_opt_load_c_offset) } pwm_xaxis_c = array, S16, 48, [12], "", { getChannelScaleByOffset(pwm_opt_load_c_offset) } , { getChannelTranslateByOffset(pwm_opt_load_c_offset) }, { getChannelMinByOffset(pwm_opt_load_c_offset) }, { getChannelMaxByOffset(pwm_opt_load_c_offset) }, { getChannelDigitsByOffset(pwm_opt_load_c_offset) } pwm_rpms_d = array, S16, 72, [6], "rpm",{ pwm_opt_curve_d == 0 ? 1 : getChannelScaleByOffset(pwm_opt_load_d_offset) } , { pwm_opt_curve_d == 0 ? 0 : getChannelTranslateByOffset(pwm_opt_load_d_offset) }, { pwm_opt_curve_d == 0 ? 0 : getChannelMinByOffset(pwm_opt_load_d_offset) }, { pwm_opt_curve_d == 0 ? rpmhigh : getChannelMaxByOffset(pwm_opt_load_d_offset) }, { pwm_opt_curve_d == 0 ? 0 : getChannelDigitsByOffset(pwm_opt_load_d_offset) } pwm_loadvals_d = array, S16, 84, [6], "%", { getChannelScaleByOffset(pwm_opt_load_d_offset) } , { getChannelTranslateByOffset(pwm_opt_load_d_offset) }, { getChannelMinByOffset(pwm_opt_load_d_offset) }, { getChannelMaxByOffset(pwm_opt_load_d_offset) }, { getChannelDigitsByOffset(pwm_opt_load_d_offset) } pwm_xaxis_d = array, S16, 72, [12], "", { getChannelScaleByOffset(pwm_opt_load_d_offset) } , { getChannelTranslateByOffset(pwm_opt_load_d_offset) }, { getChannelMinByOffset(pwm_opt_load_d_offset) }, { getChannelMaxByOffset(pwm_opt_load_d_offset) }, { getChannelDigitsByOffset(pwm_opt_load_d_offset) } pwm_rpms_e = array, S16, 96, [6], "rpm",{ pwm_opt_curve_e == 0 ? 1 : getChannelScaleByOffset(pwm_opt_load_e_offset) } , { pwm_opt_curve_e == 0 ? 0 : getChannelTranslateByOffset(pwm_opt_load_e_offset) }, { pwm_opt_curve_e == 0 ? 0 : getChannelMinByOffset(pwm_opt_load_e_offset) }, { pwm_opt_curve_e == 0 ? rpmhigh : getChannelMaxByOffset(pwm_opt_load_e_offset) }, { pwm_opt_curve_e == 0 ? 0 : getChannelDigitsByOffset(pwm_opt_load_e_offset) } pwm_loadvals_e = array, S16, 108,[6], "%", { getChannelScaleByOffset(pwm_opt_load_e_offset) } , { getChannelTranslateByOffset(pwm_opt_load_e_offset) }, { getChannelMinByOffset(pwm_opt_load_e_offset) }, { getChannelMaxByOffset(pwm_opt_load_e_offset) }, { getChannelDigitsByOffset(pwm_opt_load_e_offset) } pwm_xaxis_e = array, S16, 96, [12], "", { getChannelScaleByOffset(pwm_opt_load_e_offset) } , { getChannelTranslateByOffset(pwm_opt_load_e_offset) }, { getChannelMinByOffset(pwm_opt_load_e_offset) }, { getChannelMaxByOffset(pwm_opt_load_e_offset) }, { getChannelDigitsByOffset(pwm_opt_load_e_offset) } pwm_rpms_f = array, S16, 120, [6], "rpm",{ pwm_opt_curve_f == 0 ? 1 : getChannelScaleByOffset(pwm_opt_load_f_offset) } , { pwm_opt_curve_f == 0 ? 0 : getChannelTranslateByOffset(pwm_opt_load_f_offset) }, { pwm_opt_curve_f == 0 ? 0 : getChannelMinByOffset(pwm_opt_load_f_offset) }, { pwm_opt_curve_f == 0 ? rpmhigh : getChannelMaxByOffset(pwm_opt_load_f_offset) }, { pwm_opt_curve_f == 0 ? 0 : getChannelDigitsByOffset(pwm_opt_load_f_offset) } pwm_loadvals_f = array, S16, 132, [6], "%", { getChannelScaleByOffset(pwm_opt_load_f_offset) } , { getChannelTranslateByOffset(pwm_opt_load_f_offset) }, { getChannelMinByOffset(pwm_opt_load_f_offset) }, { getChannelMaxByOffset(pwm_opt_load_f_offset) }, { getChannelDigitsByOffset(pwm_opt_load_f_offset) } pwm_xaxis_f = array, S16, 120, [12], "", { getChannelScaleByOffset(pwm_opt_load_f_offset) } , { getChannelTranslateByOffset(pwm_opt_load_f_offset) }, { getChannelMinByOffset(pwm_opt_load_f_offset) }, { getChannelMaxByOffset(pwm_opt_load_f_offset) }, { getChannelDigitsByOffset(pwm_opt_load_f_offset) } pwm_duties_a = array, U08, 144, [6x6], "%", 1, 0, 0, 250, 0 pwm_yaxis_a = array, U08, 144, [12], "%", 1, 0, 0, 250, 0 pwm_duties_b = array, U08, 180, [6x6], "%", 1, 0, 0, 250, 0 pwm_yaxis_b = array, U08, 180, [12], "%", 1, 0, 0, 250, 0 pwm_duties_c = array, U08, 216, [6x6], "%", 1, 0, 0, 250, 0 pwm_yaxis_c = array, U08, 216, [12], "%", 1, 0, 0, 250, 0 pwm_duties_d = array, U08, 252, [6x6], "%", 1, 0, 0, 250, 0 pwm_yaxis_d = array, U08, 252, [12], "%", 1, 0, 0, 250, 0 pwm_duties_e = array, U08, 288, [6x6], "%", 1, 0, 0, 250, 0 pwm_yaxis_e = array, U08, 288, [12], "%", 1, 0, 0, 250, 0 pwm_duties_f = array, U08, 324, [6x6], "%", 1, 0, 0, 250, 0 pwm_yaxis_f = array, U08, 324, [12], "%", 1, 0, 0, 250, 0 primePWTable2 = array, S16, 360, [ 10], "ms", 0.10000, 0.00000, 0.00, 65.00, 1 ; * ( 20 bytes) crankPctTable2 = array, U16, 380, [ 10], "%", 1, 1, 1, 10000, 0 ; * ( 20 bytes) asePctTable2 = array, S16, 400, [ 10], "%", 1.00000, 0.00000, 0.00, 400.00, 0 ; * ( 2 bytes) aseCntTable2 = array, S16, 420, [ 10], "cycles", 1.00000, 0.00000, 0.00, 2500.00, 0 ; * ( 2 bytes) wueBins2 = array, U08, 440, [ 10], "%", 1.00000, 0.00000, { wue_lpg?50:100 }, 255.00, 0 ; * ( 10 bytes) #if CELSIUS temp_table_p21 = array, S16, 450, [ 10], "°C", 0.05555, -320.000, -40.00, {clthighlim}, 0 #else temp_table_p21 = array, S16, 450, [ 10], "°F", 0.10000, 0.000,-40.00, {clthighlim}, 1 #endif frpm_table4 = array , U16, 470, [ 16], "RPM", 1.00000, 0.00000, 0.00,{rpmhigh}, 0 ; * ( 24 bytes) fmap_table4 = array , S16, 502, [ 16], { bitStringValue( algorithmUnits , algorithm2 ) }, 0.10000, 0.00000, 0.00, {loadhigh}, 1 ; * ( 24 bytes) srpm_table4 = array , U16, 534, [ 16], "RPM", 1.00000, 0.00000, 0.00,{rpmhigh}, 0 ; * ( 24 bytes) smap_table4 = array , S16, 566, [ 16], { bitStringValue( algorithmUnits , IgnAlgorithm2 ) }, 0.10000, 0.00000, 0.00, {loadhigh}, 1 ; * ( 24 bytes) #if CELSIUS dualfuel_temp = array, S16, 598, [ 10], "°C", 0.05555, -320.000, -40.00, {clthighlim}, 0 #else dualfuel_temp = array, S16, 598, [ 10], "°F", 0.10000, 0.000,-40.00, {clthighlim}, 1 #endif dualfuel_temp_adj=array, S16, 618, [ 10], "%", 0.10000, 0.000,-200.00, 200.00, 1 dualfuel_press = array, S16, 638, [ 10], "kPa", 0.10000, 0.000, 70.00, 600.00, 1 dualfuel_press_adj=array, S16, 658, [ 10], "%", 0.10000, 0.000,-200.00, 200.00, 1 inj_timing_sec=array, S16, 678, [12x12], "deg", 0.10000, 0.000, -360, 720, 1 inj_timing_sec_load=array, S16, 966, [ 12], "%", 0.10000, 0.000, 0, {loadhigh}, 1 inj_timing_sec_rpm=array, U16, 990, [ 12], "rpm", 1, 0, 0, {rpmhigh}, 0 page = 12 ; 22 veTable4 = array , U16, 000, [16x16], "%", 0.10000, 0.00000, 0.00, {vehigh}, 1 ; advanceTable4 = array , S16, 512, [16x16], "deg", 0.10000, 0.00000,-10.00, 90.00, 1 ; * (288 bytes) page = 13 ; 23 ; Generic Spare Port Settings constants (on/off outputs) psEnabled = array , U08, 0, [ 48], "", 1, 0, 0, 1, 0, noSizeMutation psCondition = array , U08, 48, [ 48x2], "", 1, 0, 32, 124, 0, noSizeMutation psConnector = array , U08, 144, [ 48], "", 1, 0, 32, 124, 0, noSizeMutation psInitValue = array , U08, 192, [ 48], "", 1, 0 0, 1, 0, noSizeMutation psPortValue = array , U08, 240, [ 48], "", 1, 0, 0, 1, 0, noSizeMutation psOutSize = array , U08, 288, [ 48x2], "", 1, 0, 0, 255, 0, noSizeMutation psOutOffset = array , U16, 384, [ 48x2], "", 1, 0, 0, 1024, 0, noSizeMutation psThreshold = array , S16, 576, [ 48x2], "", 1, 0, -32768, 32767, 0, noSizeMutation psHysteresis = array , S16, 768, [ 48x2], "", 1, 0, -32768, 32767, 0, noSizeMutation ;next is 960 alternator_fvolts = array , U16, 960, [ 6], "V", 0.10000, 0.00000,6, 18, 1 ; * ( 6 bytes) alternator_freqv = array , U08, 972, [ 6], "", 1, 0.00000,0, 255, 0 ; * ( 6 bytes) #if CELSIUS alternator_temp = array, S16, 978, [ 6], "°C", 0.05555, -320.000, -40.00, {clthighlim}, 0 #else alternator_temp = array, S16, 978, [ 6], "°F", 0.10000, 0.000,-40.00, {clthighlim}, 1 #endif alternator_targvolts = array , U08, 990, [ 6], "V", 0.10000, 0.00000,6, 18, 1 ; * ( 6 bytes) alternator_dvolts = array , U16, 996, [ 6], "V", 0.10000, 0.00000,6, 18, 1 ; * ( 6 bytes) alternator_dutyv = array , U08, 1008, [ 6], "", 1, 0.00000,0, 255, 1 ; * ( 6 bytes) page = 14 ; 24 narrowband_tgts = array, U16, 0, [12x12], "V", 0.00488, 0.00000, 0, 1, 3 narrowband_tgts_rpms = array, U16, 288, [ 12], "rpm", 1.00000, 0.00000, 0, {rpmhigh}, 0 narrowband_tgts_loads = array, S16,312, [ 12], "%", 0.10000, 0.00000, 0, {loadhigh}, 1 als_opt_fc = bits, U08, 336, [0:0], "Off", "On" als_opt_sc = bits, U08, 336, [1:1], "Off", "On" als_opt_idle = bits, U08, 336, [2:2], "Off", "On" als_opt_fuel = bits, U08, 336, [3:3], "Off", "On" als_opt_pwmout= bits, U08, 336, [4:4], "Off", "On" als_opt_ri = bits, U08, 336, [5:5], "Off", "On" als_maxtime = scalar, U08, 337, "s", 0.1, 0, 1, 25.5, 1 ; als_mintps = scalar, S16, 338, "%", 0.10000, 0.00000, 0, 100, 1 als_maxtps = scalar, S16, 340, "%", 0.10000, 0.00000, 0, 100, 1 als_iac_duty = scalar, U08, 342, "%", 0.392, 0.00000, 0, 100, 1 als_iac_steps = scalar, U08, 342, "steps", 1, 0, 0, 255, 0 als_in_pin = bits, U08, 343, [0:4], "Off", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "INVALID", "INVALID", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" als_out_pin = bits, U08, 344, [0:5], "Off", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "CANOUT1", "CANOUT2", "CANOUT3", "CANOUT4", "CANOUT5", "CANOUT6", "CANOUT7", "CANOUT8", "CANOUT9", "CANOUT10", "CANOUT11", "CANOUT12", "CANOUT13", "CANOUT14", "CANOUT15", "CANOUT16" als_pwm_duty = scalar, U08, 345, "%", 1, 0, 0, 100, 0 als_pausetime = scalar, U08, 346, "s", 0.1, 0, 0, 25.5, 1 vvt_slew = scalar, U08, 347, "deg", 0.1, 0, 0.1, 25.5, 1 #if CELSIUS als_minclt = scalar, S16, 348, "°C", 0.05555, -320.000, -40.00, 150.00, 1 als_maxclt = scalar, S16, 350, "°C", 0.05555, -320.000, -40.00, 150.00, 1 #else als_minclt = scalar, S16, 348, "°F", 0.10000, 0.000,-40.00, 300.00, 1 als_maxclt = scalar, S16, 350, "°F", 0.10000, 0.000,-40.00, 300.00, 1 #endif ;ALS tables als_rpms = array, U16, 352, [6], "rpm", 1, 0, 0, {rpmhigh}, 0 als_tpss = array, U16, 364, [6], "%", 0.1, 0, 0, 100, 0 als_timing = array, S16, 376, [6x6], "degrees", 0.10000,0.00000,-50.00, 50.00,1; als_addfuel = array, S16, 448, [6x6], "%", 0.1, 0, 0, 100, 1 als_fuelcut = array, U08, 520, [6x6], "%", 1, 0, 0, 100, 0 als_sparkcut = array, U08, 556, [6x6], "%", 1, 0, 0, 100, 0 als_minrpm = scalar, U16, 592, "rpm", 1, 0, 0, {rpmhigh}, 0 als_maxrpm = scalar, U16, 594, "rpm", 1, 0, 0, {rpmhigh}, 0 #if CELSIUS als_maxmat = scalar, S16, 596, "°C", 0.05555, -320.000, -40.00, 150.00, 1 #else als_maxmat = scalar, S16, 596, "°F", 0.10000, 0.000,-40.00, 300.00, 1 #endif vvt_onoff_ang = scalar, S16, 598, "degrees", 0.10000,0.00000,0, 720.00,1; vvt_opt1_on = bits, U08, 600, [0:1], "Off", "1", "2", "4" ; vvt_opt1_dir_intake = bits, U08, 600, [2:2], "Advance", "Retard" vvt_opt1_int = bits, U08, 600, [3:3], "Synced to cam", "Timed" vvt_opt1_tst = bits, U08, 600, [4:6], "Off", "VVT1", "VVT2", "VVT3", "VVT4", "INVALID", "INVALID", "INVALID" ; 0, 1, 2, 3, 4 vvt_opt1_dir_exhaust = bits, U08, 600, [7:7], "Advance", "Retard" vvt_hold_duty = scalar, U08, 601, "%", 0.392, 0, 0, 100, 1 vvt_out1 = bits, U08, 602, [0:3], "Off", "Boost", "Idle", "VVT", "Nitrous1", "Nitrous2", "Fidle", "Inj Bank 1", "Inj Bank 2", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" vvt_out2 = bits, U08, 603, [0:3], "Off", "Boost", "Idle", "VVT", "Nitrous1", "Nitrous2", "Fidle", "Inj Bank 1", "Inj Bank 2", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" vvt_out3 = bits, U08, 604, [0:3], "Off", "Boost", "Idle", "VVT", "Nitrous1", "Nitrous2", "Fidle", "Inj Bank 1", "Inj Bank 2", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" vvt_out4 = bits, U08, 605, [0:3], "Off", "Boost", "Idle", "VVT", "Nitrous1", "Nitrous2", "Fidle", "Inj Bank 1", "Inj Bank 2", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" vvt_out1_dir = bits, U08, 602, [7:7], "Advance", "Retard" vvt_out2_dir = bits, U08, 603, [7:7], "Advance", "Retard" vvt_out3_dir = bits, U08, 604, [7:7], "Advance", "Retard" vvt_out4_dir = bits, U08, 605, [7:7], "Advance", "Retard" vvt_ctl_ms = scalar, U16, 606, "ms", 1, 0.00000, 10, 500, 0 vvt_ctl_Kp = scalar, U08, 608, "%", 1, 0.00000, 0, 200, 0 vvt_ctl_Ki = scalar, U08, 609, "%", 1, 0.00000, 0, 200, 0 vvt_ctl_Kd = scalar, U08, 610, "%", 1, 0.00000, 0, 200, 0 vvt_test_duty = scalar, U08, 611, "%", 0.392, 0.00000, 0, 100, 1 vvt_min_ang1 = scalar, S16, 612, "abs.deg.", 0.10000,0.00000,0, 720.00,1; vvt_min_ang2 = scalar, S16, 614, "abs.deg.", 0.10000,0.00000,0, 720.00,1; vvt_min_ang3 = scalar, S16, 616, "abs.deg.", 0.10000,0.00000,0, 720.00,1; vvt_min_ang4 = scalar, S16, 618, "abs.deg.", 0.10000,0.00000,0, 720.00,1; vvt_max_ang1 = scalar, S16, 620, "abs.deg.", 0.10000,0.00000,0, 720.00,1; vvt_max_ang2 = scalar, S16, 622, "abs.deg.", 0.10000,0.00000,0, 720.00,1; vvt_max_ang3 = scalar, S16, 624, "abs.deg.", 0.10000,0.00000,0, 720.00,1; vvt_max_ang4 = scalar, S16, 626, "abs.deg.", 0.10000,0.00000,0, 720.00,1; vvt_opt2_pid = bits, U08, 628, [0:0], "On/off", "PID" vvt_opt2_pid2 = bits, U08, 628, [0:0], "On/Off", "Variable" vvt_opt2_use_hold_intake = bits, U08, 628, [1:1], "Off", "On" vvt_opt2_use_hold_exhaust = bits, U08, 628, [2:2], "Off", "On" vvt_opt2_cam2pol = bits, U08, 628, [4:4], "Falling Edge", "Rising Edge" vvt_opt2_cam3pol = bits, U08, 628, [5:5], "Falling Edge", "Rising Edge" vvt_opt2_cam4pol = bits, U08, 628, [6:6], "Falling Edge", "Rising Edge" vvt_opt2_cam1pol = bits, U08, 628, [7:7], "Falling Edge", "Rising Edge" vvt_opt3_cam2 = bits, U08, 629, [0:1], "PT4", "MS3X cam PT2", "JS10 PT5", "Datalog PT6" vvt_opt3_cam3 = bits, U08, 629, [2:3], "PT4", "MS3X cam PT2", "JS10 PT5", "Datalog PT6" vvt_opt3_cam4 = bits, U08, 629, [4:5], "PT4", "MS3X cam PT2", "JS10 PT5", "Datalog PT6" vvt_opt3_cam1 = bits, U08, 629, [6:6], "Main cam", "INVALID" ; for display only vvt_timing_load = array, S16, 630, [ 8], "%", 0.10000, 0.000, 0, {loadhigh}, 1 vvt_timing_rpm = array, U16, 646, [ 8], "rpm", 1, 0, 0, {rpmhigh}, 0 vvt_timing1 = array, S16, 662, [8x8], "deg", 0.10000, 0.000, -360, 720, 1 vvt_timing2 = array, S16, 790, [8x8], "deg", 0.10000, 0.000, -360, 720, 1 vvt_tth1 = scalar, U08, 918, "", 1, 0, 0, 24, 0 vvt_tth2 = scalar, U08, 919, "", 1, 0, 0, 24, 0 vvt_tth3 = scalar, U08, 920, "", 1, 0, 0, 24, 0 vvt_tth4 = scalar, U08, 921, "", 1, 0, 0, 24, 0 vvt_coldpos1 = scalar, S16, 922, "degrees", 0.10000,0.00000,0, 720.00,1; vvt_coldpos2 = scalar, S16, 924, "degrees", 0.10000,0.00000,0, 720.00,1; tclu_opt_vss = bits, U08, 926, [0:1], "Off", "VSS1", "VSS2", "INVALID" tclu_opt_gear = bits, U08, 926, [2:2], "Off", "On" tclu_brakepin = bits, U08, 927, [0:4], "Off", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "INVALID", "INVALID", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" tclu_enablepin = bits, U08, 928, [0:4], "Off", "Tableswitch", "PE0/JS7", "PE1", "JS10", "JS11", "JS5 (ADC6)", "JS4 (ADC7)", "Nitrous In", "Launch in", "Datalog In", "PT4 Spare in", "PT2 Cam in", "PE2 Flex", "INVALID", "INVALID", "CANIN1", "CANIN2", "CANIN3", "CANIN4", "CANIN5", "CANIN6", "CANIN7", "CANIN8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" tclu_outpin = bits, U08, 929, [0:5], "Off", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "CANOUT1", "CANOUT2", "CANOUT3", "CANOUT4", "CANOUT5", "CANOUT6", "CANOUT7", "CANOUT8", "CANOUT9", "CANOUT10", "CANOUT11", "CANOUT12", "CANOUT13", "CANOUT14", "CANOUT15", "CANOUT16" tclu_gearmin = scalar, U08, 930, "", 1, 0, 0, 8, 0 tclu_delay = scalar, U08, 931, "s", 0.1, 0, 0, 10, 1 tclu_vssmin = scalar, U16, 932, { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, { msToPrefUnitsScale }, 0, 0, 1000, 0 tclu_tpsmin = scalar, S16, 934, "%", 0.1, 0, 0, 100, 1 tclu_tpsmax = scalar, S16, 936, "%", 0.1, 0, 0, 100, 1 tclu_mapmin = scalar, S16, 938, "%", 0.1, 0, 0, {loadhigh}, 1 tclu_mapmax = scalar, S16, 940, "%", 0.1, 0, 0, {loadhigh}, 1 vvt_opt4_decode = bits, U08, 942, [0:1], "Standard", "BMW V10", "BMW S54", "Hemi VVT" vvt_opt5_add1 = bits, U08, 943, [0:1], "Off", "Cam 1", "Cam 2", "INVALID" vvt_opt5_add2 = bits, U08, 943, [2:2], "Commanded", "Actual" vvt_opt5_err = bits, U08, 943, [3:3], "Yes","No" vvt_opt5_vvt1 = bits, U08, 943, [4:4], "Intake","Exhaust" vvt_opt5_vvt2 = bits, U08, 943, [5:5], "Intake","Exhaust" vvt_opt5_vvt3 = bits, U08, 943, [6:6], "Intake","Exhaust" vvt_opt5_vvt4 = bits, U08, 943, [7:7], "Intake","Exhaust" vvt_hold_duty_exh = scalar, U08, 944, "%", 0.392, 0, 0, 100, 1 vvt_ctl_Kp_exh = scalar, U08, 945, "%", 1, 0.00000, 0, 200, 0 vvt_ctl_Ki_exh = scalar, U08, 946, "%", 1, 0.00000, 0, 200, 0 vvt_ctl_Kd_exh = scalar, U08, 947, "%", 1, 0.00000, 0, 200, 0 vvt_cam1tth1 = scalar, U08, 948, "", 1, 0.00000, 0, 255, 0 vvt_cam1tth2 = scalar, U08, 949, "", 1, 0.00000, 0, 255, 0 vvt_cam2tth1 = scalar, U08, 950, "", 1, 0.00000, 0, 255, 0 vvt_cam2tth2 = scalar, U08, 951, "", 1, 0.00000, 0, 255, 0 vvt_cam3tth1 = scalar, U08, 952, "", 1, 0.00000, 0, 255, 0 vvt_cam3tth2 = scalar, U08, 953, "", 1, 0.00000, 0, 255, 0 vvt_cam4tth1 = scalar, U08, 954, "", 1, 0.00000, 0, 255, 0 vvt_cam4tth2 = scalar, U08, 955, "", 1, 0.00000, 0, 255, 0 vvt_opt6_freq = bits, U08, 956, [0:3], "1021Hz", "766Hz", "613Hz", "511Hz", "383Hz", "306Hz", "204Hz", "153Hz", "99Hz", "75Hz", "50Hz", "48Hz", "30Hz", "20Hz", "15Hz", "12Hz" vvt_opt7_yaxis = bits, U08, 957, [0:2], "Fuelload", "MAP", "% baro", "TPS", "MAFload", "INVALID", "INVALID", "INVALID" als_rifuelcut = array, U08, 958, [6x6], "%", 1, 0, 0, 100, 0 als_rirpms = array, U16, 994, [6], "rpm", 1, 0, 0, {rpmhigh}, 0 als_ritpss = array, U16, 1006, [6], "%", 0.1, 0, 0, 100, 0 als_pwm_opt_freq = bits, U08, 1018, [1:4], "On-Off", "INVALID", "250Hz", "225Hz", "200Hz", "175Hz", "150Hz", "125Hz", "100Hz", "78Hz", "39Hz", "26Hz", "19.5Hz", "15.6Hz", "13Hz", "11.1Hz" als_pwm_opt2 = bits, U08, 1019, [0:5], "INVALID", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "CANPWM1", "CANPWM2", "CANPWM3", "CANPWM4", "CANPWM5", "CANPWM6", "CANPWM7", "CANPWM8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" #if CELSIUS vvt_minclt = scalar, S16, 1020, "°C", 0.05555, -320.000, -40.00, 150.00, 1 #else vvt_minclt = scalar, S16, 1020, "°F", 0.10000, 0.000,-40.00, 300.00, 1 #endif vvt_minduty1 = scalar, U08, 1022, "%", 0.392, 0.00000, 0, 100, 1 vvt_maxduty1 = scalar, U08, 1023, "%", 0.392, 0.00000, 0, 100, 1 page = 15 ; 25 mafv = array, U16, 0, [64], "V", 0.001, 0.00000, 0.00, 5, 3 maff = array, U16, 0, [64], "Hz", { (maf_freq1 - maf_freq0) / 5000 }, { maf_freq0 * 5000 / (maf_freq1 - maf_freq0) }, {maf_freq0}, { maf_freq1 }, 0 mafflow = array, U16, 128, [64], "g/sec", {0.01 * (maf_range + 1)}, -8192, {-81 * (maf_range + 1)}, {573 * (maf_range + 1)}, 2 alphaMAPtable = array , S16, 256, [ 6x 6], "kPa", 0.10000, 0.00000, 0.00, 200.00, 1 ; * ( 72 bytes) amap_tps = array , S16, 328, [ 6], "%", 0.10000, 0.00000, 0.0, 100.00, 1 ; * ( 12 bytes) amap_rpm = array , U16, 340, [ 6], "RPM", 1.00000, 0.00000, 0.00,{rpmhigh}, 0 ; * ( 12 bytes) tpswot_tps = array , S16, 352, [ 6], "%", 0.10000, 0.00000, 0.0, 100.00, 1 ; * ( 12 bytes) tpswot_rpm = array , U16, 364, [ 6], "RPM", 1.00000, 0.00000, 0.00,{rpmhigh}, 0 ; * ( 12 bytes) #if CELSIUS matCorrTemps = array , S16, 376, [ 6], "°C", 0.05555, -320.000,-40.00, 150.00, 1 ; * ( 12 bytes) #else matCorrTemps = array , S16, 376, [ 6], "°F", 0.10000, 0.00000,-40.00, 300.00, 1 #endif matCorrDelta = array , S16, 388, [ 6], "%", 0.10000, 0.00000,-120.0, 120.0, 1 ; * ( 6 bytes) ;next is 400 boost_ctl_cl_pwm_targs1 = array, U08, 400, [8x8], "%", 1.000, 0.00000, 0.00, 100, 0 boost_ctl_cl_pwm_targs2 = array, U08, 464, [8x8], "%", 1.000, 0.00000, 0.00, 100, 0 boost_ctl_cl_pwm_rpms1 = array, U16, 528, [8], "rpm", 1, 0, 0, 25000, 0 boost_ctl_cl_pwm_rpms2 = array, U16, 544, [8], "rpm", 1, 0, 0, 25000, 0 boost_ctl_cl_pwm_targboosts1 = array, S16, 560, [8], "%", 0.10000, 0, 0, 600, 0 boost_ctl_cl_pwm_targboosts2 = array, S16, 576, [8], "%", 0.10000, 0, 0, 600, 0 blendx1 = array, S16, 592, [9], "X", 1, 0, -32767, 32767, 0 blendx2 = array, S16, 610, [9], "X", 1, 0, -32767, 32767, 0 blendx3 = array, S16, 628, [9], "X", 1, 0, -32767, 32767, 0 blendx4 = array, S16, 646, [9], "X", 1, 0, -32767, 32767, 0 blendx5 = array, S16, 664, [9], "X", 1, 0, -32767, 32767, 0 blendx6 = array, S16, 682, [9], "X", 1, 0, -32767, 32767, 0 blendx7 = array, S16, 700, [9], "X", 1, 0, -32767, 32767, 0 blendy1 = array, U08, 718, [9], "VE2", 1, 0, 0, 100, 0 blendy2 = array, U08, 727, [9], "Spk2", 1, 0, 0, 100, 0 blendy3 = array, U08, 736, [9], "VE3/4", 1, 0, 0, 100, 0 blendy4 = array, U08, 745, [9], "Spk3/4", 1, 0, 0, 100, 0 blendy5 = array, U08, 754, [9], "AFR2", 1, 0, 0, 100, 0 blendy6 = array, U08, 763, [9], "Boost2", 1, 0, 0, 100, 0 blendy7 = array, U08, 772, [9], "Crank%2", 1, 0, 0, 100, 0 ;will need to shuffle these next ones done if additional blend curves added tcslipx = array, U16, 781, [9], "Knob%", 0.0978, 0, 0, 100, 0 tcslipy = array, U08, 799, [9], "Slip threshold %", 1, 0, 0, 100, 0 fpd_duty= array, U08, 808, [6x6], "%", 0.392, 0.00000, 0, 100, 1 fpd_load= array, S16, 844, [6], "%", 0.10000, 0.00000, 0.0,{loadhigh}, 1 fpd_rpm = array, U16, 856, [6], "RPM", 1.00000, 0.00000, 0.00,{rpmhigh}, 0 #if CELSIUS fp_temps = array, S16, 868, [ 10], "°C", 0.05555, -320.000, -40.00, {clthighlim}, 0 #else fp_temps = array, S16, 868, [ 10], "°F", 0.10000, 0.000,-40.00, {clthighlim}, 1 #endif fp_temp_adj = array, S16, 888, [ 10], "%", 0.10000, 0.000,-200.00, 200.00, 1 fp_presss = array, S16, 908, [ 10], "kPa", 0.10000, 0.000, 70.00, 600.00, 1 fp_press_adj = array, S16, 928, [ 10], "%", 0.10000, 0.000,-200.00, 200.00, 1 hpte_times = array, S16, 948, [ 6], "s", 0.10000, 0.000, 0.00, 25.5, 1 hpte_afrs = array, U08, 960, [ 6], "AFR", 0.10000, 0.000, 0.00, 5.0, 1 oil_rpm = array, U16, 966, [6], "RPM", 1.00000, 0.00000, 0.00,{rpmhigh}, 0 oil_press_min = array, S16, 978, [6], "", 0.10000, 0.00000, 0.0,3276, 1 oil_press_max = array, S16, 990, [6], "", 0.10000, 0.00000, 0.0,3276, 1 alt_dutyin = array, U16, 1002, [7], "%", 1, 0, 0, 100, 0 alt_dutyout = array, U08, 1016, [7], "%", 1, 0, 0, 100, 0 page = 16 ; 26 ; this is a RAM only page with no burnable flash ; Quickform realtime data. Lower part of data is offset into outpc. Upper 3 bits are size. 0 = nothing, 1 = 1 byte, 2 = 2 bytes, 3 = 4 bytes qfrtfielddata= array, U16, 0, [ 256], "", 1.0000, 0.00000, 0.00, 65535, 0, noMsqSave ltt_table1 = array , S08, 512, [16x16], "%", 0.10000, 0.00000, -12.7, 12.7, 1, noMsqSave ; * (512 bytes) ltt_rpms = array , U16, 768, [ 16], "RPM", 1.00000, 0.00000, 0.00, {rpmhigh}, 0, noMsqSave ; * ( 24 bytes) ltt_loads = array , S16, 800, [ 16], "%", 0.10000, 0.00000, 0.00, {loadhigh}, 1, noMsqSave ; * ( 24 bytes) portusage = array, U08, 832, [ 148], "", 1, 0, 0, 255, 0, noMsqSave portusage_a = array, U08, 832, [ 8], "", 1, 0, 0, 255, 0, noMsqSave portusage_b = array, U08, 840, [ 8], "", 1, 0, 0, 255, 0, noMsqSave portusage_e = array, U08, 848, [ 8], "", 1, 0, 0, 255, 0, noMsqSave portusage_h = array, U08, 856, [ 8], "", 1, 0, 0, 255, 0, noMsqSave portusage_j = array, U08, 864, [ 8], "", 1, 0, 0, 255, 0, noMsqSave portusage_k = array, U08, 872, [ 8], "", 1, 0, 0, 255, 0, noMsqSave portusage_m = array, U08, 880, [ 8], "", 1, 0, 0, 255, 0, noMsqSave portusage_p = array, U08, 888, [ 8], "", 1, 0, 0, 255, 0, noMsqSave portusage_t = array, U08, 896, [ 8], "", 1, 0, 0, 255, 0, noMsqSave portusage_ad0h=array, U08, 904, [ 8], "", 1, 0, 0, 255, 0, noMsqSave portusage_ad0l=array, U08, 912, [ 8], "", 1, 0, 0, 255, 0, noMsqSave portusage_canin=array, U08, 920, [ 8], "", 1, 0, 0, 255, 0, noMsqSave portusage_canout=array,U08, 928, [16], "", 1, 0, 0, 255, 0, noMsqSave portusage_canadc=array,U08, 944, [24], "", 1, 0, 0, 255, 0, noMsqSave portusage_canpwm=array,U08, 968, [ 8], "", 1, 0, 0, 255, 0, noMsqSave portusage_pwmscl=array,U08, 976, [ 4], "", 1, 0, 0, 255, 0, noMsqSave page = 17 ; 27 ego_auth_table = array, U08, 0, [12x12], "%", 0.10000, 0.00000, 0, 25.5, 1 ego_auth_rpms = array, U16, 144, [ 12], "RPM", 1.00000, 0.00000, 0.00,{rpmhigh}, 0 ego_auth_loads = array, S16, 168, [ 12], { bitStringValue( algorithmUnits , (afrload ? afrload : algorithm) ) }, 0.10000, 0.00000, 0.00, {loadhigh}, 1 vsslaunch_vss = array, U16, 192, [ 10], { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, { msToPrefUnitsScale }, 0.00000, 0.00,1000, 0 vsslaunch_rpm = array, U16, 212, [ 10], "RPM", 1.00000, 0.00000, 0.00,{rpmhigh}, 0 vsslaunch_retard = array, U16, 232, [ 10], "deg", 0.10000, 0.00000, 0.00, 50, 1 ego_delay_table = array, U08, 252, [12x12], "ms", 1.00000, 0, 0, 255, 0 ego_delay_rpms = array, U16, 396, [ 12], "rpm", 1.00000, 0, 0, {rpmhigh}, 0 ego_delay_loads = array, S16, 420, [ 12], "%", 0.10000, 0, 0, {loadhigh}, 0 ego_sensor_delay = scalar,U08, 444, "ms", 1, 0, 0, 255, 0 ; 2 Generic PID channels generic_pid_flags_a_on = bits,U08, 445, [0:0], "Off", "On" generic_pid_flags_a_type = bits, U08, 445, [1:2], "INVALID","Type B","Type C", "INVALID" generic_pid_flags_a_direction = bits, U08, 445, [3:3], "Normal (higher duty = higher PV)", "Inverted (lower duty = higher PV)" generic_pid_flags_a_output_type = bits, U08, 445, [4:4], "PWM", "Stepper" generic_pid_flags_a_lookup_type = bits, U08, 445, [5:5], "Table", "Curve" generic_pid_flags_b_on = bits,U08, 446, [0:0], "Off", "On" generic_pid_flags_b_type = bits, U08, 446, [1:2], "INVALID","Type B","Type C", "INVALID" generic_pid_flags_b_direction = bits, U08, 446, [3:3], "Normal (higher duty = higher PV)", "Inverted (lower duty = higher PV)" generic_pid_flags_b_output_type = bits,U08, 446, [4:4], "PWM", "Stepper" generic_pid_flags_b_lookup_type = bits, U08, 446, [5:5], "Table", "Curve" generic_pid_pwm_opts_freq_a = bits, U08, 447, [1:4], "INVALID", "Variable Freq", "250Hz", "225Hz", "200Hz", "175Hz", "150Hz", "125Hz", "100Hz", "78Hz", "39Hz", "26Hz", "19.5Hz", "15.6Hz", "13Hz", "11.1Hz" generic_pid_pwm_opts_load_a = bits, U08, 447, [5:7], "RPM", "MAP", "% baro", "TPS", "MAFload", "CLT", "BattV", "MAT" ; ITB hidden generic_pid_pwm_opts_freq_b = bits, U08, 448, [1:4], "INVALID", "Variable Freq", "250Hz", "225Hz", "200Hz", "175Hz", "150Hz", "125Hz", "100Hz", "78Hz", "39Hz", "26Hz", "19.5Hz", "15.6Hz", "13Hz", "11.1Hz" generic_pid_pwm_opts_load_b = bits, U08, 448, [5:7], "RPM", "MAP", "% baro", "TPS", "MAFload", "CLT", "BattV", "MAT" generic_pid_pwm_outs_a = bits, U08, 449, [0:5], "INVALID", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "CANPWM1", "CANPWM2", "CANPWM3", "CANPWM4", "CANPWM5", "CANPWM6", "CANPWM7", "CANPWM8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" generic_pid_pwm_outs_b = bits, U08, 450, [0:5], "INVALID", "IAC1", "IAC2", "FIDLE", "D15", "Nitrous 1", "Nitrous 2", "Tacho", "Idle", "Boost", "VVT", "Inj Bank 1", "Inj Bank 2", "D14", "D16", "JS11", "Inj A", "Inj B", "Inj C", "Inj D", "Inj E", "Inj F", "Inj G", "Inj H", "PT4", "IGN (JS10)", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "Spk A", "Spk B", "Spk C", "Spk D", "Spk E", "Spk F", "Spk G", "Spk H", "CANPWM1", "CANPWM2", "CANPWM3", "CANPWM4", "CANPWM5", "CANPWM6", "CANPWM7", "CANPWM8", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" generic_pid_load_offset_a = scalar, U16, 451, "", 1, 0, 0, 65535, 0 generic_pid_load_offset_b = scalar, U16, 453, "", 1, 0, 0, 65535, 0 generic_pid_load_size_a = scalar, U08, 455, "", 1, 0, 0, 255, 0 generic_pid_load_size_b = scalar, U08, 456, "", 1, 0, 0, 255, 0 ; These are positioned here so that TS reads them in the correct order and the autoscaling on the next block function generic_pid_PV_offset_a = scalar, U16, 469, "", 1, 0, 0, 65535, 0 generic_pid_PV_offset_b = scalar, U16, 471, "", 1, 0, 0, 65535, 0 generic_pid_PV_size_a = scalar, U08, 473, "", 1, 0, 0, 255, 0 generic_pid_PV_size_b = scalar, U08, 474, "", 1, 0, 0, 255, 0 generic_pid_upper_inputlim_a = scalar, S16, 457, "", { getChannelScaleByOffset(generic_pid_PV_offset_a) } , { getChannelTranslateByOffset(generic_pid_PV_offset_a) }, { getChannelMinByOffset(generic_pid_PV_offset_a) }, { getChannelMaxByOffset(generic_pid_PV_offset_a) }, { getChannelDigitsByOffset(generic_pid_PV_offset_a) } generic_pid_upper_inputlim_b = scalar, S16, 459, "", { getChannelScaleByOffset(generic_pid_PV_offset_b) } , { getChannelTranslateByOffset(generic_pid_PV_offset_b) }, { getChannelMinByOffset(generic_pid_PV_offset_b) }, { getChannelMaxByOffset(generic_pid_PV_offset_b) }, { getChannelDigitsByOffset(generic_pid_PV_offset_b) } generic_pid_lower_inputlim_a = scalar, S16, 461, "", { getChannelScaleByOffset(generic_pid_PV_offset_a) } , { getChannelTranslateByOffset(generic_pid_PV_offset_a) }, { getChannelMinByOffset(generic_pid_PV_offset_a) }, { getChannelMaxByOffset(generic_pid_PV_offset_a) }, { getChannelDigitsByOffset(generic_pid_PV_offset_a) } generic_pid_lower_inputlim_b = scalar, S16, 463, "", { getChannelScaleByOffset(generic_pid_PV_offset_b) } , { getChannelTranslateByOffset(generic_pid_PV_offset_b) }, { getChannelMinByOffset(generic_pid_PV_offset_b) }, { getChannelMaxByOffset(generic_pid_PV_offset_b) }, { getChannelDigitsByOffset(generic_pid_PV_offset_b) } generic_pid_output_upperlim_a = scalar, U08, 465, "%", 0.392, 0.00000, 0, 100, 1 generic_pid_output_upperlim_b = scalar, U08, 466, "%", 0.392, 0.00000, 0, 100, 1 generic_pid_output_lowerlim_a = scalar, U08, 467, "%", 0.392, 0.00000, 0, 100, 1 generic_pid_output_lowerlim_b = scalar, U08, 468, "%", 0.392, 0.00000, 0, 100, 1 ; ; not a gap! ; generic_pid_rpms_a = array, S16, 475, [8], "rpm", 1, 0, 0, rpmhigh, 0 generic_pid_loadvals_a = array, S16, 491, [8], "%", { getChannelScaleByOffset(generic_pid_load_offset_a) } , { getChannelTranslateByOffset(generic_pid_load_offset_a) }, { getChannelMinByOffset(generic_pid_load_offset_a) }, { getChannelMaxByOffset(generic_pid_load_offset_a) }, { getChannelDigitsByOffset(generic_pid_load_offset_a) } generic_pid_rpms_b = array, S16, 507, [8], "rpm", 1, 0, 0, rpmhigh, 0 generic_pid_loadvals_b = array, S16, 523, [8], "%", { getChannelScaleByOffset(generic_pid_load_offset_b) } , { getChannelTranslateByOffset(generic_pid_load_offset_b) }, { getChannelMinByOffset(generic_pid_load_offset_b) }, { getChannelMaxByOffset(generic_pid_load_offset_b) }, { getChannelDigitsByOffset(generic_pid_load_offset_b) } generic_pid_targets_a = array, S16, 539, [8x8], "", { getChannelScaleByOffset(generic_pid_PV_offset_a) } , { getChannelTranslateByOffset(generic_pid_PV_offset_a) }, { getChannelMinByOffset(generic_pid_PV_offset_a) }, { getChannelMaxByOffset(generic_pid_PV_offset_a) }, { getChannelDigitsByOffset(generic_pid_PV_offset_a) } generic_pid_targets_b = array, S16, 667, [8x8], "", { getChannelScaleByOffset(generic_pid_PV_offset_b) } , { getChannelTranslateByOffset(generic_pid_PV_offset_b) }, { getChannelMinByOffset(generic_pid_PV_offset_b) }, { getChannelMaxByOffset(generic_pid_PV_offset_b) }, { getChannelDigitsByOffset(generic_pid_PV_offset_b) } generic_pid_control_interval_a = scalar, U08, 795, "ms", 1, 0, 10, 255, 0 generic_pid_control_interval_b = scalar, U08, 796, "ms", 1, 0, 10, 255, 0 generic_pid_P_a = scalar, U08, 797, "%", 1, 0, 0, 255, 0 generic_pid_P_b = scalar, U08, 798, "%", 1, 0, 0, 255, 0 generic_pid_I_a = scalar, U08, 799, "%", 1, 0, 0, 255, 0 generic_pid_I_b = scalar, U08, 800, "%", 1, 0, 0, 255, 0 generic_pid_D_a = scalar, U08, 801, "%", 1, 0, 0, 255, 0 generic_pid_D_b = scalar, U08, 802, "%", 1, 0, 0, 255, 0 ; 4 outmsg outmsg1_offset01 = scalar, U16, 832, "", 1, 0, 0, 512, 0 outmsg1_offset02 = scalar, U16, 834, "", 1, 0, 0, 512, 0 outmsg1_offset03 = scalar, U16, 836, "", 1, 0, 0, 512, 0 outmsg1_offset04 = scalar, U16, 838, "", 1, 0, 0, 512, 0 outmsg1_offset05 = scalar, U16, 840, "", 1, 0, 0, 512, 0 outmsg1_offset06 = scalar, U16, 842, "", 1, 0, 0, 512, 0 outmsg1_offset07 = scalar, U16, 844, "", 1, 0, 0, 512, 0 outmsg1_offset08 = scalar, U16, 846, "", 1, 0, 0, 512, 0 outmsg1_offset09 = scalar, U16, 848, "", 1, 0, 0, 512, 0 outmsg1_offset10 = scalar, U16, 850, "", 1, 0, 0, 512, 0 outmsg1_offset11 = scalar, U16, 852, "", 1, 0, 0, 512, 0 outmsg1_offset12 = scalar, U16, 854, "", 1, 0, 0, 512, 0 outmsg1_offset13 = scalar, U16, 856, "", 1, 0, 0, 512, 0 outmsg1_offset14 = scalar, U16, 858, "", 1, 0, 0, 512, 0 outmsg1_offset15 = scalar, U16, 860, "", 1, 0, 0, 512, 0 outmsg1_offset16 = scalar, U16, 862, "", 1, 0, 0, 512, 0 outmsg1_size01 = scalar, U08, 864, "", 1, 0, 0, 8, 0 outmsg1_size02 = scalar, U08, 865, "", 1, 0, 0, 8, 0 outmsg1_size03 = scalar, U08, 866, "", 1, 0, 0, 8, 0 outmsg1_size04 = scalar, U08, 867, "", 1, 0, 0, 8, 0 outmsg1_size05 = scalar, U08, 868, "", 1, 0, 0, 8, 0 outmsg1_size06 = scalar, U08, 869, "", 1, 0, 0, 8, 0 outmsg1_size07 = scalar, U08, 870, "", 1, 0, 0, 8, 0 outmsg1_size08 = scalar, U08, 871, "", 1, 0, 0, 8, 0 outmsg1_size09 = scalar, U08, 872, "", 1, 0, 0, 8, 0 outmsg1_size10 = scalar, U08, 873, "", 1, 0, 0, 8, 0 outmsg1_size11 = scalar, U08, 874, "", 1, 0, 0, 8, 0 outmsg1_size12 = scalar, U08, 875, "", 1, 0, 0, 8, 0 outmsg1_size13 = scalar, U08, 876, "", 1, 0, 0, 8, 0 outmsg1_size14 = scalar, U08, 877, "", 1, 0, 0, 8, 0 outmsg1_size15 = scalar, U08, 878, "", 1, 0, 0, 8, 0 outmsg1_size16 = scalar, U08, 879, "", 1, 0, 0, 8, 0 outmsg2_offset01 = scalar, U16, 880, "", 1, 0, 0, 512, 0 outmsg2_offset02 = scalar, U16, 882, "", 1, 0, 0, 512, 0 outmsg2_offset03 = scalar, U16, 884, "", 1, 0, 0, 512, 0 outmsg2_offset04 = scalar, U16, 886, "", 1, 0, 0, 512, 0 outmsg2_offset05 = scalar, U16, 888, "", 1, 0, 0, 512, 0 outmsg2_offset06 = scalar, U16, 890, "", 1, 0, 0, 512, 0 outmsg2_offset07 = scalar, U16, 892, "", 1, 0, 0, 512, 0 outmsg2_offset08 = scalar, U16, 894, "", 1, 0, 0, 512, 0 outmsg2_offset09 = scalar, U16, 896, "", 1, 0, 0, 512, 0 outmsg2_offset10 = scalar, U16, 898, "", 1, 0, 0, 512, 0 outmsg2_offset11 = scalar, U16, 900, "", 1, 0, 0, 512, 0 outmsg2_offset12 = scalar, U16, 902, "", 1, 0, 0, 512, 0 outmsg2_offset13 = scalar, U16, 904, "", 1, 0, 0, 512, 0 outmsg2_offset14 = scalar, U16, 906, "", 1, 0, 0, 512, 0 outmsg2_offset15 = scalar, U16, 908, "", 1, 0, 0, 512, 0 outmsg2_offset16 = scalar, U16, 910, "", 1, 0, 0, 512, 0 outmsg2_size01 = scalar, U08, 912, "", 1, 0, 0, 8, 0 outmsg2_size02 = scalar, U08, 913, "", 1, 0, 0, 8, 0 outmsg2_size03 = scalar, U08, 914, "", 1, 0, 0, 8, 0 outmsg2_size04 = scalar, U08, 915, "", 1, 0, 0, 8, 0 outmsg2_size05 = scalar, U08, 916, "", 1, 0, 0, 8, 0 outmsg2_size06 = scalar, U08, 917, "", 1, 0, 0, 8, 0 outmsg2_size07 = scalar, U08, 918, "", 1, 0, 0, 8, 0 outmsg2_size08 = scalar, U08, 919, "", 1, 0, 0, 8, 0 outmsg2_size09 = scalar, U08, 920, "", 1, 0, 0, 8, 0 outmsg2_size10 = scalar, U08, 921, "", 1, 0, 0, 8, 0 outmsg2_size11 = scalar, U08, 922, "", 1, 0, 0, 8, 0 outmsg2_size12 = scalar, U08, 923, "", 1, 0, 0, 8, 0 outmsg2_size13 = scalar, U08, 924, "", 1, 0, 0, 8, 0 outmsg2_size14 = scalar, U08, 925, "", 1, 0, 0, 8, 0 outmsg2_size15 = scalar, U08, 926, "", 1, 0, 0, 8, 0 outmsg2_size16 = scalar, U08, 927, "", 1, 0, 0, 8, 0 outmsg3_offset01 = scalar, U16, 928, "", 1, 0, 0, 512, 0 outmsg3_offset02 = scalar, U16, 930, "", 1, 0, 0, 512, 0 outmsg3_offset03 = scalar, U16, 932, "", 1, 0, 0, 512, 0 outmsg3_offset04 = scalar, U16, 934, "", 1, 0, 0, 512, 0 outmsg3_offset05 = scalar, U16, 936, "", 1, 0, 0, 512, 0 outmsg3_offset06 = scalar, U16, 938, "", 1, 0, 0, 512, 0 outmsg3_offset07 = scalar, U16, 940, "", 1, 0, 0, 512, 0 outmsg3_offset08 = scalar, U16, 942, "", 1, 0, 0, 512, 0 outmsg3_offset09 = scalar, U16, 944, "", 1, 0, 0, 512, 0 outmsg3_offset10 = scalar, U16, 946, "", 1, 0, 0, 512, 0 outmsg3_offset11 = scalar, U16, 948, "", 1, 0, 0, 512, 0 outmsg3_offset12 = scalar, U16, 950, "", 1, 0, 0, 512, 0 outmsg3_offset13 = scalar, U16, 952, "", 1, 0, 0, 512, 0 outmsg3_offset14 = scalar, U16, 954, "", 1, 0, 0, 512, 0 outmsg3_offset15 = scalar, U16, 956, "", 1, 0, 0, 512, 0 outmsg3_offset16 = scalar, U16, 958, "", 1, 0, 0, 512, 0 outmsg3_size01 = scalar, U08, 960, "", 1, 0, 0, 8, 0 outmsg3_size02 = scalar, U08, 961, "", 1, 0, 0, 8, 0 outmsg3_size03 = scalar, U08, 962, "", 1, 0, 0, 8, 0 outmsg3_size04 = scalar, U08, 963, "", 1, 0, 0, 8, 0 outmsg3_size05 = scalar, U08, 964, "", 1, 0, 0, 8, 0 outmsg3_size06 = scalar, U08, 965, "", 1, 0, 0, 8, 0 outmsg3_size07 = scalar, U08, 966, "", 1, 0, 0, 8, 0 outmsg3_size08 = scalar, U08, 967, "", 1, 0, 0, 8, 0 outmsg3_size09 = scalar, U08, 968, "", 1, 0, 0, 8, 0 outmsg3_size10 = scalar, U08, 969, "", 1, 0, 0, 8, 0 outmsg3_size11 = scalar, U08, 970, "", 1, 0, 0, 8, 0 outmsg3_size12 = scalar, U08, 971, "", 1, 0, 0, 8, 0 outmsg3_size13 = scalar, U08, 972, "", 1, 0, 0, 8, 0 outmsg3_size14 = scalar, U08, 973, "", 1, 0, 0, 8, 0 outmsg3_size15 = scalar, U08, 974, "", 1, 0, 0, 8, 0 outmsg3_size16 = scalar, U08, 975, "", 1, 0, 0, 8, 0 outmsg4_offset01 = scalar, U16, 976, "", 1, 0, 0, 512, 0 outmsg4_offset02 = scalar, U16, 978, "", 1, 0, 0, 512, 0 outmsg4_offset03 = scalar, U16, 980, "", 1, 0, 0, 512, 0 outmsg4_offset04 = scalar, U16, 982, "", 1, 0, 0, 512, 0 outmsg4_offset05 = scalar, U16, 984, "", 1, 0, 0, 512, 0 outmsg4_offset06 = scalar, U16, 986, "", 1, 0, 0, 512, 0 outmsg4_offset07 = scalar, U16, 988, "", 1, 0, 0, 512, 0 outmsg4_offset08 = scalar, U16, 990, "", 1, 0, 0, 512, 0 outmsg4_offset09 = scalar, U16, 992, "", 1, 0, 0, 512, 0 outmsg4_offset10 = scalar, U16, 994, "", 1, 0, 0, 512, 0 outmsg4_offset11 = scalar, U16, 996, "", 1, 0, 0, 512, 0 outmsg4_offset12 = scalar, U16, 998, "", 1, 0, 0, 512, 0 outmsg4_offset13 = scalar, U16, 1000, "", 1, 0, 0, 512, 0 outmsg4_offset14 = scalar, U16, 1002, "", 1, 0, 0, 512, 0 outmsg4_offset15 = scalar, U16, 1004, "", 1, 0, 0, 512, 0 outmsg4_offset16 = scalar, U16, 1006, "", 1, 0, 0, 512, 0 outmsg4_size01 = scalar, U08, 1008, "", 1, 0, 0, 8, 0 outmsg4_size02 = scalar, U08, 1009, "", 1, 0, 0, 8, 0 outmsg4_size03 = scalar, U08, 1010, "", 1, 0, 0, 8, 0 outmsg4_size04 = scalar, U08, 1011, "", 1, 0, 0, 8, 0 outmsg4_size05 = scalar, U08, 1012, "", 1, 0, 0, 8, 0 outmsg4_size06 = scalar, U08, 1013, "", 1, 0, 0, 8, 0 outmsg4_size07 = scalar, U08, 1014, "", 1, 0, 0, 8, 0 outmsg4_size08 = scalar, U08, 1015, "", 1, 0, 0, 8, 0 outmsg4_size09 = scalar, U08, 1016, "", 1, 0, 0, 8, 0 outmsg4_size10 = scalar, U08, 1017, "", 1, 0, 0, 8, 0 outmsg4_size11 = scalar, U08, 1018, "", 1, 0, 0, 8, 0 outmsg4_size12 = scalar, U08, 1019, "", 1, 0, 0, 8, 0 outmsg4_size13 = scalar, U08, 1020, "", 1, 0, 0, 8, 0 outmsg4_size14 = scalar, U08, 1021, "", 1, 0, 0, 8, 0 outmsg4_size15 = scalar, U08, 1022, "", 1, 0, 0, 8, 0 outmsg4_size16 = scalar, U08, 1023, "", 1, 0, 0, 8, 0 page = 18 ; 28 dwell_table_values = array, U08, 262, [8x8], "%", 0.10000, 0.00000, 0.5, 25.5, 1 dwell_table_rpms = array, U16, 326, [ 8], "RPM", 1.00000, 0.00000, 0.00,{rpmhigh}, 0 dwell_table_loads = array, S16, 342, [ 8], { bitStringValue( algorithmUnits , IgnAlgorithm ) }, 0.10000, 0.00000, 0.00, {loadhigh}, 1 [ConstantsExtensions] requiresPowerCycle = nCylinders requiresPowerCycle = ICIgnCapture requiresPowerCycle = engineType requiresPowerCycle = divider requiresPowerCycle = spkout_hi_lo2 ; requiresPowerCycle = triggerOffset requiresPowerCycle = triggerTeeth requiresPowerCycle = No_Miss_Teeth requiresPowerCycle = IdleCtl requiresPowerCycle = IdleCtl_alg requiresPowerCycle = IACcurlim requiresPowerCycle = IAC_tinitial_step requiresPowerCycle = hardware_spk requiresPowerCycle = hardware_cam requiresPowerCycle = hardware_fuel requiresPowerCycle = hardware_injij requiresPowerCycle = baroCorr requiresPowerCycle = egoType ; requiresPowerCycle = alternate requiresPowerCycle = twoStroke requiresPowerCycle = nInjectors requiresPowerCycle = OddFireang requiresPowerCycle = algorithm requiresPowerCycle = algorithm2 requiresPowerCycle = IgnAlgorithm requiresPowerCycle = IgnAlgorithm2 requiresPowerCycle = AfrAlgorithm requiresPowerCycle = opt142_rtc requiresPowerCycle = mycan_id requiresPowerCycle = flexFuel requiresPowerCycle = flexport requiresPowerCycle = dwellmode requiresPowerCycle = knk_option requiresPowerCycle = knkDirection requiresPowerCycle = knkpull requiresPowerCycle = knk_option_an requiresPowerCycle = knkport requiresPowerCycle = spk_conf2_gmtfi requiresPowerCycle = spk_conf2_oddodd requiresPowerCycle = spk_conf2_dli requiresPowerCycle = spk_config_campol requiresPowerCycle = spk_config_camcrank requiresPowerCycle = spk_config_trig2 requiresPowerCycle = spk_config_trig2l requiresPowerCycle = spk_config_resetcam requiresPowerCycle = spk_mode0 requiresPowerCycle = spk_mode3 requiresPowerCycle = rtbaroport requiresPowerCycle = map2port requiresPowerCycle = ego2port requiresPowerCycle = mapport requiresPowerCycle = mapport_t requiresPowerCycle = mapport_f requiresPowerCycle = knkport_an requiresPowerCycle = feature4_0igntrig requiresPowerCycle = tsw_pin_f requiresPowerCycle = tsw_pin_s requiresPowerCycle = tacho_opt3f requiresPowerCycle = launch_opt_on requiresPowerCycle = launch_opt_pins requiresPowerCycle = launch_opt_vss requiresPowerCycle = N2Oopt_2 requiresPowerCycle = N2Oopt_3 requiresPowerCycle = N2Oopt_pins requiresPowerCycle = pwmidle_freq_scale requiresPowerCycle = boost_ctl_pins_pwm requiresPowerCycle = boost_ctl_pins requiresPowerCycle = boost_ctl_pwm_scale requiresPowerCycle = boost_ctl_pwm requiresPowerCycle = boost_ctl_settings_invert_new requiresPowerCycle = afrload requiresPowerCycle = eaeload requiresPowerCycle = log_style_led requiresPowerCycle = log_style2_but requiresPowerCycle = log_style_on2 requiresPowerCycle = log_style3_adc requiresPowerCycle = sequential requiresPowerCycle = boost_feats_tsw requiresPowerCycle = launch_3step_in requiresPowerCycle = maxafr_opt1_led requiresPowerCycle = vss1_pos requiresPowerCycle = vss2_pos requiresPowerCycle = launch_var_on requiresPowerCycle = reluctorteeth1 requiresPowerCycle = reluctorteeth2 requiresPowerCycle = vss_opt1 requiresPowerCycle = vss_opt2 requiresPowerCycle = vss1_an requiresPowerCycle = vss2_an requiresPowerCycle = vss1_can_scale requiresPowerCycle = vss2_can_scale requiresPowerCycle = tsw_pin_ob requiresPowerCycle = ss_opt1 requiresPowerCycle = ss_opt2 requiresPowerCycle = wheeldia1 requiresPowerCycle = wheeldia2 requiresPowerCycle = fdratio1 requiresPowerCycle = vss1_can_id requiresPowerCycle = vss1_can_offset requiresPowerCycle = vss2_can_offset requiresPowerCycle = vss_opt0_1 requiresPowerCycle = vss_opt0_2 requiresPowerCycle = vss_opt0_3 requiresPowerCycle = vss_opt0_4 requiresPowerCycle = ss_opt1_spd requiresPowerCycle = ss1_pwmseq requiresPowerCycle = ss2_pwmseq requiresPowerCycle = gear_can_offset requiresPowerCycle = n2o1n_pins requiresPowerCycle = n2o1f_pins requiresPowerCycle = n2o2n_pins requiresPowerCycle = n2o2f_pins requiresPowerCycle = water_freq_on requiresPowerCycle = water_pins_pump requiresPowerCycle = water_pins_valve requiresPowerCycle = water_pins_in_shut requiresPowerCycle = egt_num requiresPowerCycle = accXport requiresPowerCycle = accYport requiresPowerCycle = accZport requiresPowerCycle = egt1port requiresPowerCycle = egt2port requiresPowerCycle = egt3port requiresPowerCycle = egt4port requiresPowerCycle = egt5port requiresPowerCycle = egt6port requiresPowerCycle = egt7port requiresPowerCycle = egt8port requiresPowerCycle = egt9port requiresPowerCycle = egt10port requiresPowerCycle = egt11port requiresPowerCycle = egt12port requiresPowerCycle = egt13port requiresPowerCycle = egt14port requiresPowerCycle = egt15port requiresPowerCycle = egt16port requiresPowerCycle = MAFOption requiresPowerCycle = MAFOption_t requiresPowerCycle = MAFOption_f requiresPowerCycle = vssout_opt requiresPowerCycle = vssout_optunits requiresPowerCycle = gear_method requiresPowerCycle = gear_port_an requiresPowerCycle = ac_idleup_io_in requiresPowerCycle = ac_idleup_settings requiresPowerCycle = ac_idleup_io_out requiresPowerCycle = fanctl_settings_on requiresPowerCycle = fanctl_settings_pin requiresPowerCycle = staged_extended_opts_use_v3 requiresPowerCycle = staged_extended_opts_simult requiresPowerCycle = boost_ctl_settings_on2 requiresPowerCycle = boost_ctl_settings_cl2 requiresPowerCycle = boost_ctl_pins_pwm2 requiresPowerCycle = boost_ctl_pins2 requiresPowerCycle = boost_ctl_sensor2 requiresPowerCycle = egoport1 requiresPowerCycle = egoport2 requiresPowerCycle = egoport3 requiresPowerCycle = egoport4 requiresPowerCycle = egoport5 requiresPowerCycle = egoport6 requiresPowerCycle = egoport7 requiresPowerCycle = egoport8 requiresPowerCycle = egoport9 requiresPowerCycle = egoport10 requiresPowerCycle = egoport11 requiresPowerCycle = egoport12 requiresPowerCycle = egoport13 requiresPowerCycle = egoport14 requiresPowerCycle = egoport15 requiresPowerCycle = egoport16 requiresPowerCycle = tc_opt_on requiresPowerCycle = tc_opt_method requiresPowerCycle = tc_enin requiresPowerCycle = fueltemp1 requiresPowerCycle = sensor01_source requiresPowerCycle = sensor02_source requiresPowerCycle = sensor03_source requiresPowerCycle = sensor04_source requiresPowerCycle = sensor05_source requiresPowerCycle = sensor06_source requiresPowerCycle = sensor07_source requiresPowerCycle = sensor08_source requiresPowerCycle = sensor09_source requiresPowerCycle = sensor10_source requiresPowerCycle = sensor11_source requiresPowerCycle = sensor12_source requiresPowerCycle = sensor13_source requiresPowerCycle = sensor14_source requiresPowerCycle = sensor15_source requiresPowerCycle = sensor16_source requiresPowerCycle = shift_cut_on requiresPowerCycle = shift_cut_gear requiresPowerCycle = shift_cut_in requiresPowerCycle = shift_cut_out requiresPowerCycle = pwm_opt_on_a requiresPowerCycle = pwm_opt_on_b requiresPowerCycle = pwm_opt_on_c requiresPowerCycle = pwm_opt_on_d requiresPowerCycle = pwm_opt_on_e requiresPowerCycle = pwm_opt_on_f requiresPowerCycle = pwm_opt2_a requiresPowerCycle = pwm_opt2_b requiresPowerCycle = pwm_opt2_c requiresPowerCycle = pwm_opt2_d requiresPowerCycle = pwm_opt2_e requiresPowerCycle = pwm_opt2_f requiresPowerCycle = dualfuel_sw_on requiresPowerCycle = dualfuel_pin requiresPowerCycle = dualfuel_opt_mode requiresPowerCycle = dualfuel_opt_out requiresPowerCycle = dualfuel_temp_sens requiresPowerCycle = dualfuel_press_sens requiresPowerCycle = als_opt_pwmout requiresPowerCycle = als_in_pin requiresPowerCycle = als_out_pin requiresPowerCycle = als_pwm_opt_freq requiresPowerCycle = als_pwm_opt2 requiresPowerCycle = vvt_opt1_on requiresPowerCycle = vvt_out1 requiresPowerCycle = vvt_out2 requiresPowerCycle = vvt_out3 requiresPowerCycle = vvt_out4 requiresPowerCycle = vvt_opt2_cam1pol requiresPowerCycle = vvt_opt2_cam2pol requiresPowerCycle = vvt_opt2_cam3pol requiresPowerCycle = vvt_opt2_cam4pol requiresPowerCycle = vvt_opt3_cam2 requiresPowerCycle = vvt_opt3_cam3 requiresPowerCycle = vvt_opt3_cam4 requiresPowerCycle = tclu_brakepin requiresPowerCycle = tclu_enablepin requiresPowerCycle = tclu_outpin requiresPowerCycle = vvt_opt4_decode requiresPowerCycle = vvt_opt6_freq requiresPowerCycle = knk_pin_out requiresPowerCycle = ltt_opt_on requiresPowerCycle = ltt_but_in requiresPowerCycle = ltt_led_out requiresPowerCycle = timedout1_in requiresPowerCycle = timedout1_out requiresPowerCycle = tstop_out requiresPowerCycle = NoiseFilterOpts requiresPowerCycle = map_phase_thresh requiresPowerCycle = staged_extended_opts_use_v3 requiresPowerCycle = staged_extended_opts_simult requiresPowerCycle = staged_extended_opts_pw1off requiresPowerCycle = staged_first_param requiresPowerCycle = staged_second_param requiresPowerCycle = staged_transition_on requiresPowerCycle = staged_pw1_0 requiresPowerCycle = staged_out1 requiresPowerCycle = fp_opt_mode requiresPowerCycle = fp_opt_inv requiresPowerCycle = fp_out1 requiresPowerCycle = alternator_opt_mode requiresPowerCycle = alternator_controlout requiresPowerCycle = alternator_control_inv requiresPowerCycle = alternator_freq requiresPowerCycle = alternator_lampout requiresPowerCycle = alternator_freq_monin requiresPowerCycle = alternator_freq_moninv requiresPowerCycle = alternator_freq_currin requiresPowerCycle = alternator_freq_currinv requiresPowerCycle = oilpress_in requiresPowerCycle = oilpress_out requiresPowerCycle = cel_port requiresPowerCycle = generic_pid_flags_a_on requiresPowerCycle = generic_pid_flags_b_on requiresPowerCycle = generic_pid_flags_a_direction requiresPowerCycle = generic_pid_flags_b_direction requiresPowerCycle = generic_pid_pwm_opts_freq_a requiresPowerCycle = generic_pid_pwm_opts_freq_b requiresPowerCycle = generic_pid_pwm_outs_a requiresPowerCycle = generic_pid_pwm_outs_b defaultValue = tsCanId, "CAN ID 0" defaultValue = rpmhigh, 9000 defaultValue = rpmwarn, 3000 defaultValue = rpmdang, 5000 defaultValue = loadhigh, 400 defaultValue = wue_lpg, "No" defaultValue = vehigh, 255 defaultValue = clt_exp, 0 defaultValue = sensor01Alias, "Sensor 01" defaultValue = sensor02Alias, "Sensor 02" defaultValue = sensor03Alias, "Sensor 03" defaultValue = sensor04Alias, "Sensor 04" defaultValue = sensor05Alias, "Sensor 05" defaultValue = sensor06Alias, "Sensor 06" defaultValue = sensor07Alias, "Sensor 07" defaultValue = sensor08Alias, "Sensor 08" defaultValue = sensor09Alias, "Sensor 09" defaultValue = sensor10Alias, "Sensor 10" defaultValue = sensor11Alias, "Sensor 11" defaultValue = sensor12Alias, "Sensor 12" defaultValue = sensor13Alias, "Sensor 13" defaultValue = sensor14Alias, "Sensor 14" defaultValue = sensor15Alias, "Sensor 15" defaultValue = sensor16Alias, "Sensor 16" defaultValue = prefSpeedUnits, 0 defaultValue = prefLengthUnits, 0 defaultValue = scatterRuntimeEnabled, 1 [SettingContextHelp] ; constantName = "Help Text" ; tool tips tooltips ;Ensure all settings are defined as some MS2/BG words shipped with TS are not applicable. nCylinders = "The number of cylinders or rotors in your engine." engineType = "Most engines are Even Fire. Typical odd-fire engines are V-twin, some V4, Vmax, some V6, V10." reqFuel = "Global fuel constant. Use the ReqFuel calculator. (Technically related to a pulsewidth at 100%VE)\n\nFirst, fill in all settings below and then click the [Required Fuel] button." tempTable = "" map0 = "MAP reading at 0V, typically pick a sensor from 'common MAP sensors.'" mapmax = "MAP reading at 5V, typically pick a sensor from 'common MAP sensors.'" clt0 = "" cltmult = "" mat0 = "" matmult = "" tpsMin = "With engine off, set TPS at minimum (foot off pedal) then click 'get current'" tpsMax = "With engine off, set TPS at maximum (foot to floor) then click 'get current'" batt0 = "Can be used to correct battery voltage readings." battmax = "Can be used to correct battery voltage readings." ego0 = "" egomult = "" baro0 = "Baro reading at 0V, typically pick a sensor from 'common Baro sensors.'" baromax = "Baro reading at 5V, typically pick a sensor from 'common Baro sensors.'" bcor0 = "The barometeric correction to fuel at a total vacuum.\nFor new installs set these two settings to zero and the barometric correction curve to 100% across the board.\nImported settings from older code versions use a vacuum of 147, a rate of -47 and have the curve at zero." bcormult = "The rate of change of correction.\nFor new installs set these two settings to zero and the barometric correction curve to 100% across the board.\nImported settings from older code versions use a vacuum of 147, a rate of -47 and have the curve at zero." crankTolerance = "Percentage tolerance for next input pulse while cranking." asTolerance = "Percentage tolerance for next input pulse during after start period." pulseTolerance = "Percentage tolerance for next input pulse while running." IdleCtl = "Selects method of idle control.\nNone = no idle control valve.\nOn/Off valve = basic open or closed valve (rare)\nPWM valve (2,3 wire) = common from Ford or Bosch.\nStepper (4,6 wire) = common with GM, Subaru " IdleCtl_alg = "Open-Loop controls the valve purely based on temperature.\nClosed-Loop adjusts the valve position to achieve a target RPM" IACtstep = "Time between each stepper motor step.\nIncrease this if the motor appears to behave intermittently." IAC_tinitial_step = "The length of the first motor step. Typically set a little longer to improve reliability." IACminstep = "Minimum number of steps to move in one go." IACStart = "On startup the stepper motor will move this many steps to ensure it has reached the home position. Set the value to a number larger than the number of steps required for full travel. (This was formerly called 'Start Value')" IdleCtl_home = "Whether to home the valve to the fully closed or fully open position." IACcurlim = "Stepper motor current control when not stepping.\nMoving only: turns off power between steps, motor stays cooler but may be unreliable.\nHold current: a holding current is applied between steps.\nAlways on: full current is always applied. Most heat, but reliable." iacfullopen = "Number of steps from closed to full open. Homing steps must be set to a larger number." IdleHyst = "Amount the coolant temperature must move before idle position is changed." IACcrankxt = "After the engine starts, the idle valve moves from the 'cranking position' to the 'run' position. This setting controls how long that transition takes." pwmidlecranktaper = "After the engine starts, the idle valve moves from the 'cranking position' to the 'run' position. This setting controls how long that transition takes." pwmidleset_inv = "Most valves work with 0% = closed. A few valve may work in the opposite direction." pwmidle_freq_pin = "Output for idle valve." pwmidle_freq_pin3 = "Second output for idle valve in 3-wire mode." pwmidle_freq_scale = "Frequency to operate at. This varies with valve type. Ford/Bosch valves typically operate 50-100Hz. Miata valves are closer to 300Hz." pwmidle_freq_koeo = "Determines whether the idle valve runs during Key-On-Engine-Off. This can potentially help starting by giving additional air during the first few engine rotations." fastIdleT = "Open the idle valve below this temperature for fast-idle." divider = "" alternate = "Sets injector staging in non-sequential modes. For Sequential set 2 Squirts/Alternating or 1 Squirt/Simultaneous." twoStroke = "Four-Stroke (most engines), Two-stroke or Rotary." ; injType = "Not used presently." nInjectors = "Number of primary injectors i.e. not any secondary staged injectors you may have." rpmLF = "Smoothing factors. 100% = no smoothing. 10% = highly smoothed." mapLF = "Smoothing factors. 100% = no smoothing. 10% = highly smoothed." mafLF = "Smoothing factors. 100% = no smoothing. 10% = highly smoothed." tpsLF = "Smoothing factors. 100% = no smoothing. 10% = highly smoothed." egoLF = "Smoothing factors. 100% = no smoothing. 10% = highly smoothed." adcLF = "Smoothing factors. 100% = no smoothing. 10% = highly smoothed." feature3_tps = "Automatically recalibrate TPS if negative TPS values are seen. This can be useful if the zero position on your TPS varies.\n(The temporary recalibration is not saved.)" baud = "This should be set to 115200." baudhigh = "Optional faster baudrate for SDcard datalog readback.\nUseful options are 115200, 230400, 460800.\nUse the quickest that works reliably on your hardware. A direct USB cable is likely to work best." ; These tips for on/off outputs do not show up in 2.1.13, but added for the future psEnabled = "Enables this output for programmable control. Do NOT enable an output here that is already is use for another feature e.g. idle, boost etc." psCondition = "The variable to the left (like in a datalog) is compared with the target value, the output triggers if:\n> variable is greater than target.\n= variable equals target precisely (useless)\n< variable is less than target\nAnd logical bitwise AND with the target." psConnector = "Whether to include a second condition and whether condition 1 AND condition 2 must be true or condition 1 OR condition 2." psInitValue = "Typically this is set to 0 which means the output is off." psPortValue = "Typically this is set to 1 which means the output is on when triggered." psOutSize = "" psOutOffset = "" psThreshold = "This is the target value that the variable is compared against." psHysteresis = "A deadband to prevent the output bouncing on and off." hardware_injij = "Sets the outputs for the 9th and 10th injectors I/J.\nMainboard = use the two batch fire channels.\nH3+H4 = use the spare pins on the MS3X card.\n\nIn either case ensure ALL injector drivers are identical design." firea = "Firing order is used for trim and per-cylinder corrections so the adjustment is applied to the correct cylinder number. Injectors and coils must still be wired in firing order sequence. i.e. InjA = cyl1, InjB = next cylinder to fire" enginesize = "Engine size or displacement in cc. Fill this in before using the ReqFuel calculator.\nTo convert from cu.in to cc, multiply by 16.39" staged_pri_size = "The size of each of your main/primary injectors in cc/min.\nTypical conversion from lbs/hr is multiply by 10.5" hardware_fuel = "Selects whether injectors are wired to the MS3X sequential outputs or the two batch fire outputs on the lower connector." sequential = "Off - disables sequential fuel and runs batch fire. Semi-sequential - fires injectors in pairs spread over a crank rotation (Requires a crank wheel.) Fully-Sequential - fires each injector in turn spread over a full engine cycle (requires a cam sensor on 4-stroke for phase information.)" sequential_angle_spec = "Whether to time the injection by the start, middle or end of the pulse. End is most common and typically arranged so that injection has finished just before the inlet valve opens." sequential_trim_on_off = "Whether to enable per-cylinder trim tables. This allows each cylinder to be tuned individually if you have per-cylinder widebands or EGT." baroCorr = "Enables or disables fuel adjustment for barometer (altitude.)\nOff = ignore baro\nInitial MAP reading = take a sample from the MAP sensor at power-on\nTwo independent sensors = use a second dedicated barometer sensor." rtbaroport = "The connection to an external or internal barometer sensor." baro_upper = "Maximum possible barometer reading that the engine will see. (typ. 102kPa) Limits faulty readings." baro_lower = "Lowest possible barometer reading that the engine will see. (typ. 68-80kPa) Limits faulty readings." baro_default = "Fixed barometer reading for when barometric correction is disabled." mapport_t = "Selects voltage (common) or frequency (rare) type MAP sensor input.\nOff disables the MAP input. e.g. for pure Alpha-N or MAF installs." mapport = "The connection to an external or internal voltage MAP sensor." mapport_f = "The connection to an external or internal frequency MAP sensor." map_freq0 = "The low frequency corresponding to the least MAP." map_freq1 = "The high frequency corresponding to the most MAP." map2port = "If fitted, the connection to a second voltage MAP sensor." tempUnits = "Selects the temperature units displayed on the optional MegaView." algorithm = "The calculation method for fuel. The choices are:\nSpeed Density (uses MAP sensor)\nPercent Baro (Speed-Density but with barometric pressure difference included)\nAlpha-N (uses TPS)\nMAF (uses MAF)\nITB (a mode specifically for Independent Throttle Bodies)" algorithm2 = "Enables a second modifier or blended fuel table (VE2)\n\nAdvanced use only." loadCombine = "Selects the modifier or blend method" loadMult = "Normal Speed-Density should enable 'Multiply MAP'. In rare circumstances, this can be disabled. %baro works the same. With Alpha-N, enabling multiply MAP gives 'Hybrid Alpha-N' : disabling multiply MAP gives 'Pure Alpha-N'. MAF never multiplies in MAP." loadMult2 = "The same as Multiply MAP, but this setting controls the secondary blended tables VE2 and VE4 - allowing for example Speed-Density (with MAP) on VE1 to be blended with a Pure Alpha-N (without MAP) on VE2." loadStoich = "Including the AFR target allows the VE table to be a 'real' VE table and the desired AFR to be specified in the AFR table.\nWith AFR not included, the AFR table is for reference only and the 'VE' table takes full control." stoich = "The stoichiometric (chemical ideal) AFR for the fuel in use. This is only used when 'incorporate AFR target' is enabled. For gasoline use 14.7. For alternate fuels, alter this number, alter the AFR target table and set your wideband calibration appropriately." IgnAlgorithm = "The load Y-axis for ignition table lookups" IgnAlgorithm2 = "Enables a second modifier or blended fuel table (Spk2)\n\nAdvanced use only." loadCombineign = "Selects the modifier or blend method" afrload = "The load Y-axis for AFR table lookups" eaeload = "The load Y-axis for EAE curve lookups" OvrRunC = "Over-run fuel cut is a method to totally cut off fuel during over-run situations such as coasting down a hill in gear. Be sure to set the parameters so that it is only triggered under true over-run conditions and not during regular driving." OvrRunC_progcut = "Allows sequential injectors to be cut progressively for a smoother activation.\nDo not use with staged injection." OvrRunC_progret = "Allows sequential injectors to be returned progressively for a smoother return. Does not make sense to use this with the accel-event option.\nDo not use with staged injection." OvrRunC_progign = "Allows ignition timing transition during fuel cut." OvrRunC_retign = "Allow ignition timing transition during fuel return." fc_rpm = "Typically a number of hundred RPM above idle." fc_kpa = "Typically this will be below your idle kPa." fc_tps = "This should be set close to zero such that over-run only enables when you really are off the throttle." fc_clt = "Set this to prevent over-run operation on a cold engine." fc_delay = "The delay prevents jerky on/off operation during transients." fc_ego_delay = "Over-run will give a full-lean EGO reading and closed-loop EGO should be disabled until a sensible reading is available. Set this long enough so that the EGO sensor is returning a true reading." fc_rpm_lower = "Allows a dead-band of RPM for smoother operation. Typically set this a few hundred RPM below your minimum RPM setting." fc_transition_time = "Once main fuel cut delay timer has run, this sets a transition time from normal spark advance to the advance during overrun. The timer is also used for the progressive fuel cut.\nTypically set a retarded timing for overrun with a second time for smooth activation." fc_trans_time_ret = "This sets a transition time from overrun to normal conditions and is used with progressive spark return and progressive fuel return.\nIf the throttle is applied above the threshold, the fuel and timing are immediately returned cancelling this timer." fc_ae_time = "The length of time that additional fuel is added after over-run ends to avoid a lean-spike." fc_timing = "The ignition advance during overrun. Typically set to a low number or ATDC timing." fc_ae_pct = "Fuel adder after over-run ends to avoid a lean-spike." RevLimOption_retard = "Options for spark retardation to limit revs.\nOff = no spark retard used\nProgressive Retard = timing is progressively retarded above the set RPM\nFixed angle = above the set RPM the timing is immediately changed to the angle you specify." ; RevLimNormal1 = "Timing is retarded above this RPM.\nThis also sets the start of spark cutting." RevLimMaxRtd = "Maximum timing retard." RevLimRtdAng = "Timing value used in Fixed angle." RevLimOption_spkcut = "Enables spark-cut limiting.\nCaution! This can cause catalyst damage and is noisy in operation.\nWill not work with EDIS, TFI or GMDIS" ; RevLimNormal3 = "This is the upper spark cut hard limit RPM.\nThe revlimiter starts dropping sparks above the 'retard' RPM setting." ; RevLimcutx = "Cut X/Y sparks determines how aggressive the cut is. Different engines will require different settings." ; RevLimcuty = "As above." RevLimNormal2 = "Specifies the revlimiter max RPM.\nYou must also select a rev-limiter type below." RevLimNormal2_hyst = "Sets an RPM deadband, soft limiters start this many RPM below the hard limit. If full fuel cut the RPMs must fall by this much before fuel is re-enabled. A number of hundred RPM is suggested." RevLimCLTbased = "Enables optional coolant based rev limiter, so that the rev limit can be lowered when the engine is cold. The curve itself sets the lower 'retard above' limit at your chosen temperatures." ; RevLimRpm2 = "This number is added to the limit from the curve to give the new fuel cut hard limit rpm." TpsBypassCLTRevlim = "Above this TPS% the coolant curve is ignored. This should be set to a high %age number, so that only in an emergency when you really need full throttle on a cold engine can you override the cold limit. Or set to over 100% so that the limit in the curve is always used whatever the throttle position." RevLimTPSbypassRPM = "Rev limit when above the TPS% bypass limit." RevLimOption_fuelcut = "Whether fuel-cut rev limiting is enabled." RevLimOption_fuelprog = "Enables a progressive non-rotational fuel cut that drops cylinders as revs rise between the lower and hard fuel cut limits.\nMUST NOT be used with staged or throttle-body injection." tacho_opt80 = "Enables the tacho output" tacho_opt3f = "Selects the output pin" tacho_opt40 = "Normal - an output pulse is generated matching each cylinder event. i.e. 4 cylinder engines have 4 pulses per engine cycle.\nHalf speed - output runs at half speed. This can enable a 4-cyl tacho to be used on an 8-cyl engine." fanctl_settings_on = "Enables fan control" fanctl_settings_idleup = "Whether the fan activation should also raise the idle" fanctl_settings_pin = "Selects the output pin for the fan relay" fanctl_idleup_delay = "How long to wait after raising idle before turning on fan" fanctl_idleup_adder_duty = "PWM open-loop duty cycle to increase by" fanctl_idleup_adder_steps = "Additional stepper idle steps to open" fan_idleup_cl_targetadder = "Target rpm to increase by" fanctl_ontemp = "Turn fan on above this temperature" fanctl_offtemp = "Turn fan off below this temperature (must be lower than "on" temperature)" fanctl_opt2_engineoff = "Allows fan to run in key-on, engine-off situation" fan_ctl_settings_acfan = "Whether the fan should be automatically turned on to help cool the A/C radiator." fan_idleup_tps_offpoint = "Disable fan above this TPS% (reduces load on engine when max power desired.)" fan_idleup_tps_hyst = "Deadband of TPS% " fan_idleup_vss_offpoint = "Disable fan above this vehicle speed (at high speeds airflow through radiator will be sufficient on its own.)" fan_idleup_vss_hyst = "Deadband of VSS" tclu_outpin = "Selects output port to connect to lockup solenoid " tclu_enablepin = "Selects optional input port for enable switch (could be used for 4th gear pressure switch.) " tclu_brakepin = "Selects optional input port for brake light switch (brake light unlocks convertor.) " tclu_tpsmin = "Minimum TPS to enable lockup " tclu_tpsmax = "Maximum TPS to enable lockup " tclu_mapmin = "Minimum MAP to enable lockup " tclu_mapmax = "Maximum MAP to enable lockup " tclu_opt_vss = "Optionally allow VSS1 or VSS2 speed input as criteria " tclu_vssmin = "Sets minimum speed for lockup. (Requires VSS input in speed/gear sensors.) " tclu_opt_gear = "Optionally allows gear number as criteria. (Requires gear to be enable in speed/gear sensors.) " tclu_gearmin = "Minimum gear to enable lockup " tclu_delay = "Wait this long after conditions are met before locking up." MAFOption_t = "Selects between 0-5V voltage input (e.g. most MAFs) or frequency input (e.g. GM)\nOff disables the MAF input. " MAFOption = "Selects the hardware input pin where the voltage MAF is connected." MAFOption_f = "Selects from four possible frequency input pins." maf_freq0 = "The frequency the MAF outputs to indicate least air flow." maf_freq1 = "The frequency the MAF outputs to indicate greatest air flow." feature7_mafmat = "Optionally enables a trim curve based on MAT sensor input." feature7_maftrim = "Optionally enables VE table 1 as a trim table. Fill the table with 100% to begin with. " maf_range = "Sets the range to match your MAF sensor. Set this before loading a MAF calibration curve. On gasoline, 650g/s ~800hp; 1300g/s ~1600hp; 1950g/s ~2400hp and 2600g/s ~3200hp. Use the lowest range suitable for better low-end precision. " feature7_mafcalib = "Select this if you want to use MAF in the 'old way' as per 1.1.x and earlier. See the 1.1.x MAF manual page. " opentime_opt1_master = "Same = one dead-time across all injectors. Most common.\n\nIndividual = the dead time for each injector is set individually." opentime_opt1 = "You can choose one of the four battery voltage correction curves. (If in doubt pick curve 1 and leave the curve alone.)" injOpena = "Injector dead time.\nTypically 0.7ms for low-z (~2.5ohm) and 0.9ms for high-z (~14ohm)" injOpen1 = "Injector dead time.\nTypically 0.9ms for high-z (~14ohm)" opentime_opta_pwm = "Enables PWM current limiting (peak and hold) for low ohm injectors." injPwmPd = "The period/frequency during the hold phase. Safe to leave at 66us." injPwmT = "This the 'peak' time and is typically set to 1-1.5ms" injPwmP = "This is the 'hold' percentage current. 30-50% is typical." opentime_optb_own = "Enables different settings for bank 2. Only applicable if physically different injectors are on the second bank. Could be used with staged injection.\nFor most engines, this should be set to Off." opentime_opta = "You can choose one of the four battery voltage correction curves. (If in doubt pick curve 1 and leave the curve alone.)" smallpw_opt1_master = "The Injector Small Pulsewidths feature allows the user to make a correction and make the non-linear region more linear in nature. Unless you have calibration data for your injectors measured on your Megasquirt, this feature should be left turned off. " smallpw2_opt1_master = "The Injector Small Pulsewidths feature allows the user to make a correction and make the non-linear region more linear in nature. Unless you have calibration data for your injectors measured on your Megasquirt, this feature should be left turned off. \n\nThis setting applies to table switched different injectors." staged_first_param = "This setting enables staged injection and sets the primary staging parameter, which is used to determine when to engage the secondary injectors.\nFor table-based staging, 0% means not staged at all, and 100% means fully staged, between is partially staged." staged_sec_size = "Size of secondary injectors in cc/min" staged_extended_opts_pw1off = "Off = when staged, primary and secondary pulse-widths are equal.\n\nOn = when staged, primaries are shut down completely and just secondary injectors are used." staged_extended_opts_use_v3 = "Whether the secondaries are connected to MS3X outputs or to the mainboard 'V3' batch fire outputs." staged_extended_opts_simult = "Whether the batch fire outputs alternate during an engine cycle or fire once together." staged_transition_on = "Allows a gradual transition into staging instead of a hard switch point." staged_transition_events = "how many ignition events it will take to go from no staging to fully staged." staged_primary_delay = "Delays the reduction of the primary pulse width by a number of ignition events after the secondaries start coming online." staged_secondary_enrichment = "This setting is used to inject more fuel on the secondaries than the fully staged calculation determines. This is useful when there is a small lean spot just after staged injection fully engages." staged_param_1 = "Used to determine when staged injection engages when using RPM, MAP, TPS, or Duty." staged_hyst_1 = "Used as a deadband to determine when staged injection shuts off." staged_second_param = "This setting is used to add a second method for determining when to stage." staged_param_2 = "Used to determine when staged injection engages when using RPM, MAP, TPS, or Duty." staged_hyst_2 = "Used as a deadband to determine when staged injection shuts off." staged_second_logic = "Whether both parameters or either parameter will enable staging." staged_out1 = "Use a relay output to enable secondary injectors (GM systems) where primary and secondary injectors are wired to the same injector output." staged_out2 = "Use a relay output earlier than secondary injectors (GM air-flaps)." staged_out1_inv = "Allows output polarity sense to be swapped" staged_out2_inv = "Allows output polarity sense to be swapped" staged_out2_time = "How long the pre-output is active before the staging transition begins." flexFuel = "This enables or disables the Flex Fuel system." flexport = "Selects where the sensor is connected." fueltemp1 = "If used, specifies a sensor input for fuel temperature." fuelFreq0 = "The low and high frequencies generated by the sensor (e.g. 50Hz, 150Hz for the GM sensor)" flex_pct0 = "The ethanol percentage corresponding to the low and high frequencies." fuelCorr0 = "The fuel multiplier. 100% means no change. The default of 163% for fully ethanol gives 63% additional fuel." fuelSpkDel0 = "The timing addition in degrees. E85 burns more slowly than pure gasoline and will require more advance." ff_tpw0 = "The pulsewidth from the sensor at low and high temperatures (1.0, 5.0ms for GM)" ff_temp0 = "The low/high temperatures at low/high pulsewidths" fuelCorr_default = "Multiplier to be used if the sensor sends an out of range frequency. (Faulty sensor or an error condition.)" fuelSpkDel_default = "Timing to add under fault conditions. (Expected to be 0 or negative.)" fuelFreq1 = "" flex_pct1 = "" fuelCorr1 = "" fuelSpkDel1 = "" flex_baseline = "Ethanol percentage in regular fuel, assumes that the main fuel and spark tables are tuned for regular fuel. Allows flex-fuel system to be enabled without retuning base tables. Set to 0 for backwards compatability." egoAlgorithm = "None - no fuel changes are made in response to oxygen sensor readings.\nSimple - This method of closed-loop EGO control is well-suited to use with a narrowband O2 sensor. \nPID - This method incorporates a Proportional Integral Derivative control loop which tuned properly, adjusts the amount of fuel being injected to quickly get to the target, and then maintains the target without any oscillation." egoAlgorithm_auth = "Enables a table of EGO authority based on RPM/load. This allows greater control over when closed-loop EGO is operational and permits variable authority. An authority of zero means there will be no correction made. Normally the RPM and load axes should be set the same as the AFR tables." egoCount = "The number of ignition events between each correction." egoDelta = "controls how large each correction 'step' is." egoLimit = "The maximum amount of adjustment performed by the closed-loop algorithm." ego_lower_bound = "Only correct above this AFR" ego_upper_bound = "Only correct below this AFR" egoTemp = "Only correct above this temperature." egoRPM = "Only correct above this RPM." TPSOXLimit = "Only correct below this throttle position." MAPOXLimit = "Only correct below this load." MAPOXMin = "Only correct above this load." ego_startdelay = "Only correct when engine has been running at least this long." egoKP = "Proportional term" egoKI = "Integral term" egoKD = "Differential term" egoType = "Disabled - No EGO sensor enabled.\nNarrowband = Enable narrowband sensor/s.\nWideband = Enable wideband sensor/s" egonum = "Selects the number of oxygen sensors in use." egoport1 = "Selects where the sensor or controller is connected." egomap1 = "Selects which oxygen sensor applies to this cylinder if multiple sensors are used. When only a single sensor is fitted, ensure all cylinders are set to EGO1." spk_mode0 = "Sets the type of tach input pattern decoder to be used." triggerOffset = "In 'Basic Trigger' and 'Trigger Return' this specifies the engine angle BTDC that each trigger pulse is received.\n\nIn 'Toothed Wheel' this should always be set to zero - use tooth#1 angle instead.\n\nIn other modes this setting can make a +/- 20 degree adjustment to the built-in reference angle." trigret_ang = "This is only used in CAS 4/1 mode and specifies the angular length of each tooth." OddFireang = "For oddfire engines this specifies the angle the engine must rotate from spark A output to spark B output." spk_conf2_gmtfi = "GM HEI, Ford TFI and Buick C3I specific options.\nWith HEI7/8 and GM-DIS, this setting enables the 'bypass' output on spark B.\nThe C3I mode enables the 'bypass' and also quick-sync after the cam signal is received.\n Signature PIP mode is used with 'Basic Trigger' and allows the Megasquirt to use these distributors (where one vane is shorter than the others) for sequential fuel." spk_conf2_oddodd = "Alternate = most oddfires such as Ford V4, Chevy V6, Viper V10\n\nPaired = Yamaha Vmax\n\nCustom = set your own oddfire angles." no_skip_pulses = "The number of tach input pulses at start-up that are ignored before ignition calculations and wheel decoding begins. The default value of 3 is suitable for most applications." ICIgnCapture = "This must be matched to your tach input. If it is set incorrectly you can experience timing drift with rpms or misdetection of missing teeth on a missing tooth wheel. The tooth logger can be used to confirm polarity is correct." spkout_hi_lo2 = "This setting is CRITICAL or you will melt your ignition coils. For 99% of installs using the MS3X spark outputs, this should be set to 'Going high'" spk_mode3 = "Specifies the type of ignition coils in use. TFI, HEI, EDIS, GMDIS must set 'single coil'" hardware_spk = "Either MS3X or LEDs. The MS3X outputs are ready to use logic spark outputs. The 'LED' spark outputs will typically only be used on upgrades from MS2 or without the MS3X." hardware_cam = "Either MS3X or JS10. The MS3X input is ready to use. JS10 requires DIY board customisation." spk_mode3_tach3 = "Selects where the tertiary tach input is connected" spk_mode3_hirespol = "Selects whether to flip polarity on hi-res tach input." timing_flags = "Fixed Advance = locks timing to the value set below. This is used for confirming timing with a strobe timing light during setup.\n\nUse table = normal operation where the spark advance table is used." use_prediction = "1st Deriv Prediction = engine accleration deceleration is allowed for in timing calculation. (Normal setting)\n\nNo Prediction = no allowance." fixed_timing = "The timing to lock to in 'Fixed' mode" crank_dwell = "Specifies the base coil dwell time during cranking before battery correction is applied." crank_timing = "Specifies the ignition advance to be used while cranking. Typically 5-10 deg BTDC" spk_conf2_dli = "Enables specific multiplexed outputs for use with the Toyota ignition module such as used on the 7MGTE." dwellmode = "Standard Dwell - this is the setting to use for most installs.\n\vFixed Duty - locks the spark output to a constant duty cycle instead of controlling dwell. e.g. Ford's 'Push Start' TFI modules, Bosch 'smart' ignition modules, or MSD and other CD boxes.\n\nTime After Spark - only intended for Saab Tri-Ionic DI cassettes.\n\vCharge at trigger - rarely used. Could be used with MSD type CDI boxes when running Basic Trigger only." spk_conf2_dwell = "For time-after-spark, the dwell can be varied with rpm." spk_conf2_dwelltbl = "For 'standard dwell', a table of dwell values can be used. Normally a single dwell value is used." max_coil_dur = "The base dwell time before battery voltage correction. Typical values are 3-4 ms." max_spk_dur = "The time required for the spark to complete, typically in the order of 1 millisecond." dwelltime = "The backwards dwell time for Time-After-Spark" dwellduty = "For fixed duty, this specifies the %age duty cycle of the output signal." hw_latency = "If you notice a slight retarding of ignition timing with rpm while strobing with fixed timing, you can enter a small number in here to remedy it." feature4_0igntrig = "For Trigger Return mode only, the middle LED on the case can be used to echo the input signal from the distributor to help in setting up the base timing." spk_mode3_trim = "Enables the adjustment of timing per individual cylinder." spk_config_trig2 = "Single wheel with missing tooth = typically a crank wheel such as 36-1 or 60-2\n\nDual wheel = two wheels without missing teeth e.g. Nippodenso 24/1 CAS\n\nDual wheel with missing tooth = typically a 36-1, 60-2 crank wheel and an additional cam wheel." triggerTeeth = "The number of effective teeth, counting the missing teeth as if they existed. i.e. a 36-1 wheel has 35 physical teeth, but enter 36." No_Miss_Teeth = "The number of missing teeth. Common are 1 for 36-1, or 2 for 60-2 or 36-2" Miss_ang = "See the 'Trigger Wheel' section of the manual for more detail on this important setting." spk_config_camcrank = "Does the main wheel rotate at crankshaft speed or camshaft (distributor) speed." spk_config_trig2l = "Like ignition input capture above, specifies which voltage level is considered 'active'" spk_config_campol = "In 'Poll level' mode specifies which voltage level is used for each engine phase." spk_config_resetcam = "How often are second trigger (e.g. cam) input pulses received." poll_level_tooth = "Which crank tooth number to poll the cam level at. Default is 0.\nRover 4.6 try 17.\nChanging the tooth no. may also change the phase." oddfireangs1 = "Number of crank degrees engine rotates from Spk A to Spk B" oddfireangs2 = "Number of crank degrees engine rotates from Spk B to next cyl" oddfireangs3 = "Number of crank degrees engine rotates from Spk C to next cyl" oddfireangs4 = "Number of crank degrees engine rotates from Spk D to next cyl" mapsample_opt2 = "'Use event average' is useful for most engines.\n\n'Use timed min' is intended for 1cyl, V twins with highly cyclic MAP signals." map_sample_duration = "How many degrees to sample over. The starting angle is set in the curve above." mapsample_opt1 = "How many ignition events to sample over. Typically set to 1 for large engines or 2 for 1,2 cylinder." map_phase_thresh = "When using the MAP sensor to detect engine phase, this sets a pressure threshold that can identify the intake vs. exhaust phases. Will be highly engine dependent, 80kPa worked on a small 1-cyl." fp_opt_mode = "On/Off is used for basic control where the Megasquirt controls the negative side of a relay.\nOpen-Loop PWM provides a table based duty cycle for a fuel pump controller.\nClosed-Loop PWM monitors actual rail pressure and adjusts the duty cycle output to the pump controller to maintain a set differential pressure." fp_ctl_ms = "How often to run the control calculations" fp_out1 = "The output used to control the fuel pump (either to the relay or to a controller.)" fp_freq = "For PWM outputs, this sets the output frequency." fp_opt_inv = "Set to 'Normal' for On/Off. This setting is useful for PWM outputs and should be set to 'Invert' when using one of the mid-current ECU outputs as they invert the signal. The Spark or Digital outputs do not invert the signal and 'Normal' should be used. Note that the on/off fuel pump output is always a low-side driver and connects to the negative side of the relay - changing this setting will have no impact on that." fp_opt_reg = "By preference, fuel systems use a vacuum/boost referenced regulator that maintains line pressure Xbar above inlet pressure. Some GM fuel systems use a fixed fuel pressure referenced to ambient air pressure instead. The vac referenced systems give even injector flow across all inlet pressure conditions. The un-referenced systems give a varying flow and require a calculation within the ECU to compensate. Enabling 'Fixed' here turns on that automatic compensation." fp_opt_safety = "Enables fuel pressure safety system.\nIf the measured fuel pressure drops too low for more than a set time, the engine is shutdown." rail_pressure_psig = "The fuel rail pressure in PSI referenced to manifold pressure. Typically 43.5PSI for many installs." rail_pressure_kpag = "The fuel rail pressure in kPa referenced to manifold pressure. Typically 304kPa for many installs." fp_prime_duty = "The PWM duty cycle used during the priming pulse." fp_off_duty = "The PWM duty cycle used when the pump should be off. Set to 0 for most applications, or 75% for Ford FPDM modules." fp_min_duty = "The minimum PWM duty cycle to be used when running. Set to 0 for most applications, or 5% for Ford FPDM modules." fp_max_duty = "The maximum PWM duty cycle to be used when running. Set to 100 for most applications, or 50% for Ford FPDM modules." fp_press_in = "If used, specifies a Generic Sensor that is configured for fuel pressure in kPa." fp_press_type = "'Gauge' sensors are referenced to atmospheric pressure - with a vac referenced regulator, the reported pressure will drop under vacuum and increase under boost.\n'Differential' sensors are referenced to manifold vacuum/boost - this pressure will typically remain static e.g. 43psi, 3bar.\n'Absolute' sensors are referenced to true vaccum and will read about 14.7psi/1bar when there is no fuel pressure." fueltemp1_corr = "Enables fuel correction based on fuel temperature." fp_Kp = "Closed-loop Proportional term" fp_Ki = "Closed-loop Integral term" fp_Kd = "Closed-loop Differential term" hpte_opt_on = "Allows richer mixture after prolonged high power operation to cool piston crown. The richer mixture is calculated by decreasing the AFR target using the number from the curve. The 'high power timer' counts up when above the load/rpm points and counts down below those points. The relevant enrichment is applied until the counter returns to zero." hpte_load = "Only enable above this fuel-load." hpte_rpm = "Only enable above this RPM." shiftlight_opt_pins = "Allows a specific output to be used to switch a shift light. (Do not also enable the same output in the generic on/off outputs.)" shiftlight_opt_gear = "Allows per-gear limits, can be useful to set a lower limit in lower gears to avoid overshooting." shiftlight_limit1 = "Light is on above this RPM." ltt_opt_on = "Enables the long-term fuel trim. This is intended to automatically make minor corrections in fuelling AFTER the engine is fully tuned. It requires EGO control to be enabled and operational." ltt_opt_feedback = "Reports the total %change in 'sensor15' - mainly for testing." ltt_samp_time = "How often (in seconds) the code checks the current EGO correction." ltt_agg = "How softly the trim correction is applied." ltt_opt_mode = "Timed - if needed, the trim table is automatically saved to flash\nButton - an external button is used to save the trim table to flash." ltt_but_in = "User operated button to burn trim table from RAM to flash so it is used at next power-on." ltt_int = "Minimum time between automatic burns to flash." ltt_led_out = "LED output is illuminated when RAM trim table exceeds change threshold. The user can then choose to Burn to flash." ltt_thresh = "If the sum of all changes exceeds this threshold than a burn to flash is requested - either automatically or by lighting the LED for user intervention. The purpose is to only make permanent changes if there was a widespread change." pwmidle_closed_duty = "The duty below which changes in duty no longer have an effect on RPM" pwmidle_closed_steps = "The number of steps below which changes in duty no longer have an effect on RPM" pwmidle_open_duty = "The duty above which changes in duty no longer have an effect on RPM" pwmidle_open_steps = "The number of steps above which changes in duty no longer have an effect on RPM" pwmidle_dp_adder = "The amount to increase the idle valve duty/steps by when throttle is lifted. Should be set to a value that results in RPM being slightly above the target RPM." pwmidle_dp_adder_steps = "The amount to increase the idle valve duty/steps by when throttle is lifted. Should be set to a value that results in RPM being slightly above the target RPM." pwmidle_close_delay = "This setting controls the amount of time between pressing the throttle and closing the valve while driving. A value of 0 disables this setting. NOTE: The timer does not start until actual RPM is 200 RPM above the target." pwmidle_max_rpm_new = "Use this setting to tune how agressively the idle speed controller tries to reach the target RPM. Adjust the slider up until the idle speed starts oscillating, then back down until it stops. Wait 5-10 seconds between each adjustment to give the controller a chance to settle." pwmidle_cl_opts_initvaluetable = "This setting controls whether the initial duty value used upon entering closed-loop idle is taken from the last time in closed-loop or taken from the initial value table." pwmidle_cl_opts_initval_clt = "This setting is used to set whether the initial values table y-axis lookup is done using CLT or MAT." pwmidle_shift_lower_rpm = "The RPM above which the idle valve will remain closed when shifting gears." pwmidle_shift_open_time = "The longest amount of time that a shift takes. After this timer expires, the valve will follow normal dashpot behavior." pwmidle_cl_opts_display_pid = "Basic mode uses P=100, I=100, D=0\nAdvanced enables the ability to individually set PID gains for cases where the controller cannot be tuned to reach the target adequately in Basic." pwmidle_Kp_new = "Proportional gain for closed-loop idle PID loop. Reacts immediately to change in RPM." pwmidle_Ki_new = "Integral gain for closed-loop idle PID loop. Reacts to sustained difference between target RPM and actual RPM." pwmidle_Kd_new = "Derivative gain for closed-loop idle PID loop. Reacts to rate of change of RPM." pwmidle_pid_wait_timer = "Controls how long all conditions for entering closed-loop idle must be met for before entering closed-loop control." pwmidle_targ_ramptime = "How long after entering closed-loop idle it will take for actual RPM to match target RPM." pwmidle_ms = "Controls how often the closed-loop idle algorithm runs." pwmidle_rpmdot_disablepid = "Use so that engaging clutch without throttle does not leave PID running. Avoids situations where PID stays running while not actually idling causing stalls once PID is entered again." IdleCtl_vss = "Controls whether the VSS activates closed-loop idle." idleminvss = "Closed-loop idle is disabled above this VSS." pwmidle_tps_threshold = "The TPS value below which the other factors for entering closed-loop idle are considered." pwmidle_rpmdot_threshold = "The value RPMdot must be below before closed-loop idle can be activated." pwmidle_decelload_threshold = "The value load must be above before closed-loop idle can be activated." boost_ctl_settings_on = "Controls whether boost control is enabled." boost_ctl_settings_initialvals = "For use with closed-loop boost control. Controls whether the initial values table is used to set the initial duty before closed-loop is engaged." boost_ctl_pwm = "Controls the frequency range allowed on the boost control output(s). Mid allows 12-1021 Hz. Slow allows 11.1-78Hz" boost_ctl_pwm_scale = "Frequencies available with Mid solenoid frequency range. Frequency is shared with other pins in the same PWM group.\rPWM group A : Nitrous1/2, Inj1/2\rPWM group B : Boost, Idle, FIDLE, VVT" boost_ctl_pins_pwm = "Output pins available when using the Mid frequency range." boost_ctl_settings_freq = "Frequencies available when using the Slow frequency range." boost_ctl_pins = "Output pins available when using the Slow frequency range." boost_ctl_settings_invert_new = "Set this so that higher duty yields higher boost." boost_ctl_ms = "Controls how often the boost control algorithm runs." boost_ctl_closeduty = "(Closed-loop) The duty below which changes in duty no longer cause changes in boost pressure." boost_ctl_openduty = "(Closed-loop) The duty above which changes in duty no longer cause changes in boost pressure." boost_ctl_clt_threshold = "Coolant temperature must be above this value before boost control will work." boost_ctl_lowerlimit = "(Closed-loop) Boost pressure must be within this many kPa of the target boost before closed-loop control will activate.\n\nOutside of this range the valve is held wide open (keeping the wastegate shut) for fastest spooling." boost_ctl_settings_cl = "Controls whether open loop or closed-loop control algorithm is used." boost_ctl_Kp = "Proportional gain for closed-loop control. Proportional control causes immediate changes to output duty with changes in boost error." boost_ctl_Ki = "Integral gain for closed-loop control. Integral control causes changes in duty with boost error over time. The longer boost is off target, the stronger the reaction due to the integral term." boost_ctl_Kd = "Derivative gain for closed-loop control. Derivative control causes larger reactions in boost duty with faster rate of change of boost error. The faster error changes, the more duty will change to counteract." boost_ctl_sensitivity = "Use this setting to tune how agressively the boost controller tries to reach the target boost. Adjust the slider up until the boost oscillates around the target, then back down until it stops." boost_ctl_settings_tunemode = "Basic: uses fixed PID parameters P=100,I=100,D=100\n\nAdvanced: uses adjustable PID parameters for greater control." OverBoostOption = "Selection can be fuel cut, spark cut, or both. Fuel cut only cuts fuel, spark cut only cuts spark, both cuts both fuel and spark." OverBoostKpa = "Maximum desired boost before overboost protection cuts fuel/spark." OverBoostHyst = "After overboost protection is enabled, how far below the maximum boost must boost drop before spark/fuel are re-enabled." OverBoostOption_tol = "Trips the overboost protection if boost is a certain pressure above boost target. Allows overboost to track the boost target table." boosttol = "How far MAP can exceed the boost target before overboost cuts in." tsw_pin_ob = "Allows an input pin to toggle maximum boost to an alternate value." OverBoostKpa2 = "The alternate maximum desired boost before overboost protection cuts fuel/spark." ; overboostcutx = "When using spark cut, controls the number of sparks to cut." ; overboostcuty = "When using spark cut, controls the number of potential spark events from which to cut spark." boost_feats_tsw = "Allow boost tables to be switched when an input is toggled on/off." boost_gear_switch = "Selects which gear to switch tables on when gear-based boost table switching is enabled." boost_feats_timed = "Launch control must be enabled to use this feature. Times the amount of boost from launch." boost_feats_launch = "Allow a specific target (closed-loop) or duty (open loop) to be specified when launch control is active." boost_launch_duty = "Duty to use when launch is active." boost_launch_target = "Target to use when launch is active." boost_vss = "Requires VSS to be enabled. Allows boost duty or target to be controlled based on vehicle speed or detected gear." boost_vss_tps = "TPS must be above this value for the VSS target boost to be used." boost_geartarg1 = "Boost target for each gear.\n\nTo use these settings you need:\n Boost = On\nClosed-Loop Boost\nGear detection\n Boost vs speed/gear = Gear." boost_ctl_settings_on2 = "Controls whether the second channel of boost control is enabled." boost_ctl_pins_pwm2 = "Output for solenoid." boost_ctl_pins2 = "Output for solenoid." boost_ctl_closeduty2 = "The duty below which changes in duty no longer cause changes in boost pressure." boost_ctl_openduty2 = "The duty above which changes in duty no longer cause changes in boost pressure." boost_ctl_lowerlimit2 = "(Closed-loop) Boost pressure must be within this many kPa of the target boost before closed-loop control will activate.\n\nOutside of this range the valve is held wide open (keeping the wastegate shut) for fastest spooling." boost_ctl_settings_cl2 = "Controls whether open loop or closed-loop control algorithm is used." boost_ctl_Kp2 = "Proportional gain for closed-loop control. Proportional control causes immediate changes to output duty with changes in boost error." boost_ctl_Ki2 = "Integral gain for closed-loop control. Integral control causes changes in duty with boost error over time. The longer boost is off target, the stronger the reaction due to the integral term." boost_ctl_Kd2 = "Derivative gain for closed-loop control. Derivative control causes larger reactions in boost duty with faster rate of change of boost error. The faster error changes, the more duty will change to counteract." boost_ctl_sensor2 = "MAP sensor input to monitor." alternator_opt_mode = "Control mode for alternator.\nOff = disabled\nOn-Off = most basic control, typically on the 'L' lamp terminal\nOpen-loop frequency = Frequency applied sets target voltage (Ford)\nOpen-loop duty = Duty cycle applied sets target voltage (GM)\nClosed-loop field control = MS3 uses a closed-loop algorithm to control the alternator field to target a voltage (Chrysler)\nHigh-speed feedback field switching = MS3 monitors the voltage at 20kHz and switches the field on or off to match the monitored voltage to the target voltage. (99-05 Miata)" alternator_ctl_ms = "How often to run the control calculations" alternator_controlout = "Output connection to the alternator" alternator_control_inv = "Whether a positive or negative active edge is used" alternator_freq = "Frequency used for control output signal" alternator_lampout = "Output for charge/warning light" alternator_freq_currin = "PWM digital input used for monitoring battery current. (Display only.)" alternator_diff = "Light warning lamp if actual voltage is too far away from target." alternator_freq_monin = "PWM digital input from alternator as load sense - often the 'F' terminal." alternator_freq_moninv = "Whether a positive or negative capture edge is used" alternator_maxload = "Light warning lamp if sensed load is above this limit." alternator_Kp = "Closed-loop Proportional term" alternator_Ki = "Closed-loop Integral term" alternator_Kd = "Closed-loop Differential term" alternator_sensitivity = "Overall sensitivity" alternator_freq_currinv = "Whether a positive or negative capture edge is used" alternator_startdelay = "How long after start before alternator control is enabled. Allows engine to stablise before alternator load is applied." alternator_ramptime = "Time to ramp up to target voltage" alternator_tempin = "If used, specifies a Generic Sensor that is configured for battery temperature. The temperature is then used to lookup a target charging voltage from the upper curve." alternator_targv = "Target voltage when in 'Charge' mode" alternator_chargetime = "How long after start is considered 'Charge' before transitioning to 'Run' mode." alternator_targvr = "Target voltage during 'Run' mode." alternator_wot = "TPS% to trigger Wide Open Throttle (WOT) mode" alternator_wotv = "Target voltage when in WOT mode, typically set lower than normal to free up some engine power." alternator_wottimeout = "Timeout before WOT mode ends and target voltage returns to charge or run mode." alternator_overrv = "Target voltage when over-run fuel cut is active. Setting a slightly higher voltage here will give a minor 'regenerative braking' effect." rpmhigh = "The maximum for RPM on gauges, tables, curves and entry boxes.\nAdjust to suit your engine." rpmwarn = "The RPM 'warning' on gauges - yellow" rpmdang = "The RPM 'danger' on gauges - red" loadhigh = "The maximum 'load' value e.g. kPa on gauges, tables, curves and entry boxes." vehigh = "The maximum for VE values." wue_lpg = "For most installs, setting warmup enrichment (WUE) to below 100% indicates a serious tuning mistake and the code will flag up a 'Configuration Error' to alert the user. In rare conditions such as using LPG (propane) for fuel, it can be valid. This setting disables the Config Error warning message." prefSpeedUnits = "Chooses the speed units - either Mile-per-hour or Kilometres-per-hour\nClose the page and re-open after changing." prefLengthUnits = "Chooses the size units - either metres or inches\nClose the page and re-open after changing." clt_exp = "Allows gauges and curves to use an expanded coolant temperature range for air-cooled engines using the CLT sensor to measure oil or head-temperature." maxafr_opt1_on = "Enables the AFR safety system" maxafr_opt1_led = "Sets an on/off warning output" maxafr_opt1_load = "Selects the load axis on the AFR difference table" maxafr_en_load = "Only check above this TPS/kPa" maxafr_en_rpm = "Only check above this RPM" maxafr_en_time = "Specifies a wait time before taking action, to prevent transients from tripping." maxafr_spkcut_time = "Cuts spark as the first stage in the system for this long." maxafr_ret_tps = "throttle is below this limit." maxafr_ret_map = "Fuel and spark remain cut until MAP (boost) is below this limit." maxafr_ret_rpm = "Fuel and spark remain cut until RPM is below this limit." feature3_3 = "Sequenced batch fire can be useful to give more repeatable engine operation. On every startup the batch firing is aligned to the same ignition event (cylinder). Without this feature the alignment is random." trig_init = "Specifies the ignition 'trigger'. Typically try 0 or 1." dlyct = "Sets the CPU hardware based noise filter. Typically a small number or zero." NoiseFilterOpts = "Enables the noise filtering. Uses the curve to set the filter period. The filter measures the width of the tach-in pulse in order to reject short noise spikes and allow through valid wider tach-in pulses. Typically set to 1000us or more at low revs and 100us or more at high revs. Basic distributor setups can use far larger numbers." NoiseFilterOpts1 = "Enables ignoring of bogus tach pulses, they will still be recorded in the composite logger." NoiseFilterOpts2 = "The tach input is disabled for a short period of time after a valid tach pulse to mask out any bogus tach pulses." ICISR_tmask = "The absolute time after a valid tach pulse when new pulses are ignored. The time value here depends greatly on the type of tach input in use.\ne.g. a 60-2 wheel spinning at 10000rpm has a real tach pulse every 0.1ms. A distributor pickup on a 4-cyl at 600rpm has a real tach pulse every 50ms.\nThis value must be set to less than the shortest ever valid time on your install." ICISR_pmask = "This works as a percentage of the last valid tooth time. 30-50% are typical values." secondtrigopts = "Enables a simple noise filter on the cam tach input." TC5_required_width = "Equivalent to the time on the curve used for the crank input." secondtrigopts1 = "Enables ignoring of bogus tach pulses, they will still be recorded in the composite logger." secondtrigopts2 = "The tach input is disabled for a short period of time after a valid tach pulse to mask out any bogus tach pulses." IC2ISR_tmask = "The absolute time after a valid tach pulse when new pulses are ignored. The time value here depends greatly on the type of tach input in use.\ne.g. a 60-2 wheel spinning at 10000rpm has a real tach pulse every 0.1ms. A distributor pickup on a 4-cyl at 600rpm has a real tach pulse every 50ms.\nThis value must be set to less than the shortest ever valid time on your install." IC2ISR_pmask = "This works as a percentage of the last valid tooth time. 30-50% are typical values." crankingRPM = "Set this a few hundred RPM above your typical fast cranking speed." floodClear = "Above this throttle position no fuel will be injected during cranking to help clear a flood situation. It will also disable priming." feature7_batchcrank = "Allows fuel to be fired on each tach event in a batch-fire mode on a sequential install. Can be useful in cold climates to allow large cranking fuel flow." feature7_cranktaper = "Allows a taper curve on crank pulsewidth, either to reduce pulsewidth over time, or to allow an initial large shot of fuel." feature7_crtpunits = "Selects units of ignition events or 0.1 seconds." alternate_blend = "Enables a blend curve between cranking curves." altcrank = "Engines with many cylinders such as V12 may find that the injecting fuel on every tach event gives difficult hot starting due to small pulsewidths.\nThis option allows the fuel to be injected on alternate events (with twice the pulse width)" primedelay = "Delays the priming pulses to allow a lazy fuel pump to build pressure." feature3_matase = "Can be used to help with perceived heat-soak issues." feature3_aseunit = "Selects whether After Start Enrichment (ASE) uses Seconds or Ignition Events as the timer." shift_cut_on = "Enables the sequential / bike shift cut system." shift_cut_auto = "Whether the system operates from a pushbutton or automatically." shift_cut_in = "Input used for the button." shift_cut_out = "Output to the shift solenoid." shift_cut_rpm = "Minimum RPM to allow shifting." shift_cut_tps = "Minimum throttle to allow shifting." shift_cut_delay = "The solenoid is activated immediately, then wait this long before cutting spark." shift_cut_time = "How long to cut spark for." shift_cut_gear = "Option to add additional spark cut time per gear." shift_cut_add12 = "Additional time to cut spark for this shift." shift_cut_add23 = "Additional time to cut spark for this shift." shift_cut_add34 = "Additional time to cut spark for this shift." shift_cut_add45 = "Additional time to cut spark for this shift." shift_cut_add56 = "Additional time to cut spark for this shift." shift_cut_soldelay = "How long to keep the solenoid powered after the spark is returned." shift_cut_reshift = "Ignore button for this long after shifting - to prevent a false shift." shift_cut_rpm12 = "Shift at this rpm." shift_cut_rpm23 = "Shift at this rpm." shift_cut_rpm34 = "Shift at this rpm." shift_cut_rpm45 = "Shift at this rpm." shift_cut_rpm56 = "Shift at this rpm." ac_idleup_settings = "Enables the A/C idle-up feature." ac_idleup_io_out = "Output to engage compressor." ac_idleup_io_in = "Switch input." ac_idleup_delay = "Delay after switch is pressed before engaging compressor." ac_idleup_min_rpm = "Lowest RPM that AC compressor can be turned on." ac_delay_since_last_on = "Sets a delay to prevent rapid cycling on/off." ac_idleup_adder_duty = "Additional PWM idle duty cycle to add when A/C is active." ac_idleup_adder_steps= "Additional idle steps to add when A/C is active." ac_idleup_cl_targetadder= "Bump up RPM by this much when A/C is active." ac_idleup_cl_lockout_mapadder = "When A/C is active the engine load will increase. Set this number so that the additional load doesn't kick you out of closed-loop idle." ac_idleup_tps_offpoint = "Disable A/C when TPS is above this. (Reduces load on engine when driver demands full power.)" ac_idleup_tps_hyst = "Deadband in TPS to prevent bouncing on/off." ac_idleup_vss_offpoint = "Disable A/C above this speed." ac_idleup_vss_hyst = "Deadband in VSS to prevent bouncing on/off." idleadvance_on = "Enables Idle-advance feature" idle_special_ops_timing_assist = "Enables additional advance curve linked to closed-loop idle target. This allows you to use timing control to assist with idle speed regulation." idleveadv_to_pid_idleadv = "Either links idle-advance with closed-loop idle or allows idle advance to have its own conditions." idleadvance_tps = "Only activate below this TPS." idleadvance_rpm = "Only activate below this RPM." idleadvance_load = "Only activate above this load. (Helps code ignore over-run situations.)" idleadvance_clt = "Only activate above this coolant temperature. (Typically idle-advance does not work too well during warmup.)" idleadvance_delay = "After the conditions are met, wait this long before enabling idle-advance. This helps reduce false activations." idleve_on = "Enables Idle-VE feature" idleveadv_to_pid_idleve = "Either links idle-advance with closed-loop idle or allows idle advance to have its own conditions." idleve_tps = "Only activate below this TPS." idleve_rpm = "Only activate below this RPM." idleve_load = "Only activate above this load. (Helps code ignore over-run situations.)" idleve_clt = "Only activate above this coolant temperature. (Typically idle-VE does not work too well during warmup.)" idleve_vsson = "Selects whether VSS1 must be zero before idle-VE is activated." idleve_delay = "After the conditions are met, wait this long before enabling idle-advance. This helps reduce false activations." knk_option = "Disabled: do not use knock feedback for ignition advance control\nSafe Mode: use knock retard, but keep the advance below that which caused knock. This backs the advance 1 small step back and leaves it at that until TPS or MAP changes - or knock comes back. This is 'safe mode' scheme is the safest thing for a DIY set-up.\nAggressive Mode: use knock retard, but keep advance at threshold of knock occurring. That is, the program advances (up to the timing table value) if it doesn't see knock, and retards if does see knock. The difference from safe mode is that the timing can be advance all the way to the table value after knock, not just up to one step below knock. This may result in the knock returning, in which case the timing is retarded again, then advanced slowly, and so on." knk_option_an = "On/Off: basic on/off 'knock' or 'no-knock' external input.\nAnalogue: external analogue input proportional to knock signal level\nInternal: internal knock module." knkport = "Input for knock on/off signal" knkDirection = "The logic input level. i.e. when set to 'low' then a 0V signal means there is knock. This matches the GM module" knkpull = "Whether an internal pull-resistor should be applied. When using the suggested Datalog/Tableswitch/Launch input pin set to 'None'" knkport_an = "Input for knock analogue signal" knk_option_wind = "Either read single analogue value at end knock window or peak detect." knk_pin_out = "Optional digital output for knock window signal." knk_ndet = "Number of knock events detected before control is started." knk_maxmap = "Disable knock retard above this MAP." knk_lorpm = "Knock control is implemented above this RPM" knk_hirpm = "Knock control is implemented below this RPM" knk_maxrtd = "Maximum total retard when knock occurs." knk_trtd = "The time between knock retard corrections" knk_step1 = "How much to retard by on each correction step when knock is first detected. Make it large to quickly retard the timing and stop knock." knk_step2 = "How much to retard by on each correction step if knock restarts after it had stopped." knk_tadv = "The time between knock advance corrections (i.e. timing return to normal)" knk_step_adv = "The ignition advance step size after knock has stopped." knk_dtble_adv = "If ignition table timing changes by this much then return to normal timing as operating in different area." knock_bpass = "This should be adjusted to suit the resonant frequency of you engine." knock_int = "How long the signal is sampled for." knock_conf_num = "How many knock sensors (1 or 2)" knock_conf_launch = "Knock detection can be disabled when launch/flatshift are active to prevent false detection." knock_conf_percyl = "Enables linking of knock signal to cylinder number. This only works if coil-on-plug or sequential fuel are enabled." knock_gain01 = "Compensate for sensor sensitivity and distance between cylinder and sensor." knock_sens01 = "Pick which sensor to use for each cylinder." AE_options = "Selects between time-based accel enrichment or pump-style enrichment." EAEOption = "Enables a well-wetting transient system." feature7_aetpswot = "Enables a curve to model effective 100% TPS for a given RPM. This allows smaller throttle movements to be more responsive at lower RPMs and ignores changes in throttle above 'wide-open'." mapThresh = "Trigger enrichment above this MAPdot value." aeEndPW = "After main enrichment event, taper down to this amount of enrichment.\n0 is suggested." feature7_aeevents = "Length of enrichment pulse is measured in ignition events or seconds." tpsasync_events = "Length of enrichment pulse." tpsasync2_events = "Length of enrichment taper." taeTime = "Length of main enrichment pulse." aeTaperTime = "Length of 'taper' time after main enrichment pulse.\n0 is suggested." tpsThresh = "Trigger enrichment above this TPSdot value." tdePct = "Deceleration fuel cut amount in percent. 100% is no cut, 0% is complete cut of fuel.\n100% is suggested." taeColdA = "At full cold (-40C/F), add this amount to the enrichment." taeColdM = "At full cold (-40C/F), multiply the enrichment by this percentage." ae_lorpm = "Below this RPM full enrichment is enabled." ae_hirpm = "Above this RPM, there is no enrichment. In between the enrichment is on a sliding scale." tpsProportion = "The balance between MAPdot and TPSdot for accel enrichment. 0% is fully MAPdot, 100% is fully TPSdot." accel_mapdot_threshold = "Trigger enrichment above this MAPdot value." accel_tpsdot_threshold = "Trigger enrichment above this TPSdot value." accel_CLT_multiplier = "At full cold (-40C/F), multiply the enrichment by this percentage." accel_blend_percent = "The balance between MAPdot and TPSdot for accel enrichment. 0% is fully MAPdot, 100% is fully TPSdot." als_in_pin = "Enables the Anti-Lag system and selects the Enable input." als_maxtps = "Disable ALS above this TPS%." als_minrpm = "Disable ALS below this RPM." als_maxrpm = "Disable ALS above this RPM." als_maxmat = "Disable ALS above this manifold temperature." als_maxtime = "Only allow ALS to be active for this long to reduce temperature build-up." als_pausetime = "Enforce a minimum time between activations to reduce temperature build-up." als_minclt = "Disable ALS below this coolant temperature." als_maxclt = "Disable ALS above this coolant temperature." als_opt_fc = "Whether cyclic fuel cut should be used. ONLY for use with sequential fuel." als_opt_sc = "Whether cyclic spark cut should be used." als_opt_ri = "Whether roving idle fuel cut should be used." als_opt_idle = "Enables the idle valve in ALS mode." als_iac_duty = "What valve duty should be used to give the extra air needed for ALS." als_iac_steps = "What valve steps should be used to give the extra air needed for ALS." als_out_pin = "Enables an additional output in ALS mode for extra-air valve." als_opt_pwmout = "Enables an additional pulsed output in ALS mode." als_pwm_opt2 = "Pulsed output." als_pwm_duty = "Duty cycle on pulsed output when ALS is active." als_pwm_opt_freq = "Frequency on pulsed output." vvt_opt1_on = "Enables VVT control and selects number of cams to control." vvt_opt4_decode = "Enables a special decoder if applicable.\n\nThe BMW S54 decoder uses the cam3 and cam4 outputs as the complementary pairs for cam1 and cam2. i.e. wire outputs 1&3 to solenoid 1, wire outputs 2&4 to solenoid 2. Set 3,4 to the opposite direction." vvt_opt6_freq = "VVT solenoid PWM frequency." vvt_opt2_pid2 = "Chooses between basic on/off mode or variable position control." vvt_opt5_add1 = "Whether to adjust injection timing based on cam position and which cam." vvt_opt5_add2 = "If injector timing is being adjusted, whether to adjust it based on target or actual current position." vvt_onoff_ang = "Angle to advance injector timing by when VVT is active." vvt_opt7_yaxis = "The load unit used for the Y-axis on the lookup tables." vvt_opt1_int = "How often to run the calculations.\nSynced to cam is most typical meaning that the calculations are run as soon as new cam tooth passes the sensor." vvt_ctl_ms = "Specifies a fixed calculation interval." vvt_opt5_err = "Whether error checking should be applied to the measured cam angles." vvt_opt1_tst = "Selects a cam output to test." vvt_test_duty = "What duty cycle to output to the VVT solenoid." vvt_opt2_use_hold_intake = "Some VVT systems will hold at a fixed position when a certain duty cycle is applied, enable this on those systems. Others have no specific hold-duty." vvt_hold_duty = "Specific hold duty." vvt_ctl_Kp = "Proportional gain for closed-loop control. Proportional control causes immediate changes to output duty with changes in VVT position difference." vvt_ctl_Ki = "Integral gain for closed-loop control. Integral control causes changes in duty with VVT position difference over time. The longer VVT is off target, the stronger the reaction due to the integral term." vvt_ctl_Kd = "Derivative gain for closed-loop control. Derivative control causes larger reactions in duty with faster rate of change of VVT position difference. The faster the difference changes, the more duty will change to counteract." vvt_opt2_use_hold_exhaust = "Some VVT systems will hold at a fixed position when a certain duty cycle is applied, enable this on those systems. Others have no specific hold-duty." vvt_hold_duty_exh = "Specific hold duty." vvt_ctl_Kp_exh = "Proportional gain for closed-loop control. Proportional control causes immediate changes to output duty with changes in VVT position difference." vvt_ctl_Ki_exh = "Integral gain for closed-loop control. Integral control causes changes in duty with VVT position difference over time. The longer VVT is off target, the stronger the reaction due to the integral term." vvt_ctl_Kd_exh = "Derivative gain for closed-loop control. Derivative control causes larger reactions in duty with faster rate of change of VVT position difference. The faster the difference changes, the more duty will change to counteract." vvt_opt1_dir_exhaust = "Whether the exhaust cam table is a table of advances (old method) or a table of retards (matches most exhaust VVTs.)" vvt_opt3_cam1 = "Cam1 is always the main cam input." vvt_opt2_cam1pol = "Cam1 capture polarity is defined on the Ignition Options page." vvt_tth1 = "The number of teeth on the cam1 trigger wheel." vvt_out1 = "VVT1 solenoid output" vvt_min_ang1 = "The minimum absolute angle from the cam sensor." vvt_max_ang1 = "The maximum absolute angle from the cam sensor." vvt_opt5_vvt1 = "Whether this is an intake or exhaust cam." vvt_cam1tth1 = "Application specific, look for cam tooth after this crank tooth." vvt_cam1tth2 = "Application specific, look for cam tooth after this crank tooth." vvt_out1_dir = "What direction the cam moves with output duty." vvt_opt3_cam2 = "The input for cam2." vvt_opt2_cam2pol = "The capture polarity for cam2.\n(If reported cam angle changes unexpectedly with RPM while the cam is stationary, try swapping polarity." vvt_tth2 = "The number of teeth on the cam2 trigger wheel." vvt_out2 = "VVT2 solenoid output" vvt_min_ang2 = "The minimum absolute angle from the cam sensor." vvt_max_ang2 = "The maximum absolute angle from the cam sensor." vvt_opt5_vvt2 = "Whether this is an intake or exhaust cam." vvt_cam2tth1 = "Application specific, look for cam tooth after this crank tooth." vvt_cam2tth2 = "Application specific, look for cam tooth after this crank tooth." vvt_out2_dir = "What direction the cam moves with output duty." vvt_opt3_cam3 = "The input for cam3." vvt_opt2_cam3pol = "The capture polarity for cam3.\n(If reported cam angle changes unexpectedly with RPM while the cam is stationary, try swapping polarity." vvt_tth3 = "The number of teeth on the cam3 trigger wheel." vvt_out3 = "VVT3 solenoid output" vvt_min_ang3 = "The minimum absolute angle from the cam sensor." vvt_max_ang3 = "The maximum absolute angle from the cam sensor." vvt_opt5_vvt3 = "Whether this is an intake or exhaust cam." vvt_cam3tth1 = "Application specific, look for cam tooth after this crank tooth." vvt_cam3tth2 = "Application specific, look for cam tooth after this crank tooth." vvt_out3_dir = "What direction the cam moves with output duty." vvt_opt3_cam4 = "The input for cam4." vvt_opt2_cam4pol = "The capture polarity for cam4.\n(If reported cam angle changes unexpectedly with RPM while the cam is stationary, try swapping polarity." vvt_tth4 = "The number of teeth on the cam4 trigger wheel." vvt_out4 = "VVT4 solenoid output" vvt_min_ang4 = "The minimum absolute angle from the cam sensor." vvt_max_ang4 = "The maximum absolute angle from the cam sensor." vvt_opt5_vvt4 = "Whether this is an intake or exhaust cam." vvt_cam4tth1 = "Application specific, look for cam tooth after this crank tooth." vvt_cam4tth2 = "Application specific, look for cam tooth after this crank tooth." vvt_out4_dir = "What direction the cam moves with output duty." vvt_minclt = "VVT only operates when coolant is above this temperature." vvt_minduty1 = "Minimum duty cycle for VVT solenoids" vvt_maxduty1 = "Maximum duty cycle for VVT solenoids" vvt_slew = "Limits rate of change of VVT target to minimise overshoot caused by rapid target changes or low oil pressure at low rpms.\nDefault is 2.0deg per cam event." f5_0_tsf = "Enables fuel table switching." f5_0_tsf_opt = "Hardware = Physical switch or blend curve\nRPM,kPa,TPS allow switching above threshold set below." tsw_pin_f = "Table switch input." tsf_rpm = "RPM threshold." tsf_kpa = "kPa threshold." tsf_tps = "TPS threshold." f5_0_tss = "Enables spark table switching." f5_0_tss_opt = "Hardware = Physical switch or blend curve\nRPM,kPa,TPS allow switching above threshold set below." tsw_pin_s = "Table switch input." tss_rpm = "RPM threshold." tss_kpa = "kPa threshold." tss_tps = "TPS threshold." tsw_pin_rf = "Enables ReqFuel switch input." ReqFuel_alt = "ReqFuel to use when switched." tsw_pin_afr = "Enables AFR table switch input." tsw_pin_stoich = "Enables Stoich switch input." stoich_alt = "Stoich to use when switched." dualfuel_sw_on = "Enables Dual Fuel support (e.g. LPG or secondary race fuel on a different system.)" dualfuel_opt_mode = "Switching = swaps from fuel 1 to fuel 2.\nDual Table = parallel fuel tables allowing simultaneous control of both fuels. e.g. mapped methanol under boost." dualfuel_opt_out = "Shared outputs = used when two sets of injectors share one set of control wires from the ECU and have a relay to switch +12V.\nDifferent outputs = where each main and secondary injectors are wired to different outputs." dualfuel_pin = "Input for Dual Fuel switching." dualfuel_sw_fuel = "Whether to switch fuel tables." dualfuel_sw_spk = "Whether to switch spark tables." dualfuel_sw_afr = "Whether to switch AFR tables." dualfuel_sw_rf = "Whether to switch ReqFuel." dualfuel_sw_stoich = "Whether to switch Stoich." dualfuel_sw_wue = "Whether to switch warmup curves." dualfuel_sw_ase = "Whether to switch afterstart curves." dualfuel_sw2_prime = "Whether to switch priming curves." dualfuel_sw2_crank = "Whether to switch cranking pulse curves." dualfuel_sw2_injp = "Whether to switch injector parameters." dualfuel_sw2_smpw = "Whether to switch small pulsewidth curves." dualfuel_sw2_ob = "Whether to switch overboost limits." dualfuel_sw2_boosw = "Whether to switch boost tables." dualfuel_opt_temp = "Enable secondary fuel temperature adjustment." dualfuel_temp_sens = "Secondary fuel temperature input." dualfuel_opt_press = "Enable secondary fuel pressure adjustment." dualfuel_press_sens = "Secondary fuel pressure input." dualfuel_press_type = "Sensor type: Gauge, Absolute, Differential" vss_opt0_1 = "Type of speed sensor connection.\nDigital = any pulse input or capture from an expansion board.\nAnalogue = 0-5V input directly reporting speed (rare.)" vss1_an = "Input for analogue 0-5V speed sensor." vss1_an_max = "Speed at 5V input." vss_opt1 = "Selects digital pulse input or input via CAN from expansion board." wheeldia1 = "Overall diameter of wheel and tyre." vss1_pos = "Whether speed sensor teeth are mounted\n-Directly on the wheel\n-on the driveline/trans\n-as pulses per mile\n-as pulse per km." reluctorteeth1 = "Number of teeth on speed pickup reluctor." vss1_pwmseq = "CAN PWM port for capturing from expansion board." vss1_can_scale = "Scaler to convert from one unit system to another. (Megasquirt uses 0.1 ms-2 internally, so to convert from 0.1 mph use 45.6%" vss1_can_scale_pulse = "Number of pulses per mile/km" vss1LF = "Smoothing factor. 100% = no smoothing, 15% = maximum smoothing." vss_opt0_2 = "Type of speed sensor connection.\nDigital = any pulse input or capture from an expansion board.\nAnalogue = 0-5V input directly reporting speed (rare.)" vss2_an = "Input for analogue 0-5V speed sensor." vss2_an_max = "Speed at 5V input." vss_opt2 = "Selects digital pulse input or input via CAN from expansion board." wheeldia2 = "Overall diameter of wheel and tyre." vss2_pos = "Whether speed sensor teeth are mounted\n-Directly on the wheel\n-on the driveline/trans\n-as pulses per mile\n-as pulse per km." reluctorteeth2 = "Number of teeth on speed pickup reluctor." vss2_pwmseq = "CAN PWM port for capturing from expansion board." vss2_can_scale = "Scaler to convert from one unit system to another. (Megasquirt uses 0.1 ms-2 internally, so to convert from 0.1 mph use 45.6%" vss1_can_scale_pulse = "Number of pulses per mile/km" vss2LF = "Smoothing factor. 100% = no smoothing, 15% = maximum smoothing." vss_opt0_3 = "Type of speed sensor connection.\nDigital = any pulse input or capture from an expansion board.\nAnalogue = 0-5V input directly reporting speed (rare.)" vss3_an = "Input for analogue 0-5V speed sensor." vss_opt3 = "Selects digital pulse input or input via CAN from expansion board." vss3_pwmseq = "CAN PWM port for capturing from expansion board." vss_opt0_4 = "Type of speed sensor connection.\nDigital = any pulse input or capture from an expansion board.\nAnalogue = 0-5V input directly reporting speed (rare.)" vss4_an = "Input for analogue 0-5V speed sensor." vss_opt4 = "Selects digital pulse input or input via CAN from expansion board." vss4_pwmseq = "CAN PWM port for capturing from expansion board." vssout_opt = "Digital pulsed output to drive a speedometer." vssout_optunits = "Type of output conversion." vssout_scale = "Scaling factor." vssdot_int = "How often to calculate VSSdot (acceleration.)" vssdotLF = "Smoothing factor on VSSdot. 100% = no smoothing, 15% = maximum smoothing." fdratio1 = "Final drive gear ratio." gear_method = "How to determine gear no.\nVSS/RPM - compares the vehicle speed with RPM and the gear ratio table.\nAnalogue - uses a 0-5V analogue gear-position-sensor input.\nCAN gear# - fetches a gear number from an expansion board over CAN." gear_no = "How many gears." gear1ratio = "Ratio of each gear." gear_port_an = "Analogue input for gear-position-sensor." gear0v = "Nominal voltage in each position." ss_opt1 = "Selects digital pulse input." reluctorteeth3 = "Number of pickup teeth on reluctor." ss_opt1_spd = "Where possible, configures this as a high-speed input." ss1LF = "Smoothing factor. 100% = no smoothing, 15% = maximum smoothing." ss_opt2 = "Selects digital pulse input." reluctorteeth4 = "Number of pickup teeth on reluctor." ss_opt2_spd = "Where possible, configures this as a high-speed input." ss2LF = "Smoothing factor. 100% = no smoothing, 15% = maximum smoothing." accXport = "Analogue 0-5V input for X-axis." accYport = "Analogue 0-5V input for Y-axis." accZport = "Analogue 0-5V input for Z-axis." accXcal1 = "Calibration value when X is -1g. See the manual." accXcal2 = "Calibration value when X is +1g. See the manual." accYcal1 = "Calibration value when Y is -1g. See the manual." accYcal2 = "Calibration value when Y is +1g. See the manual." accZcal1 = "Calibration value when Z is -1g. See the manual." accZcal2 = "Calibration value when Z is +1g. See the manual." accxyzLF = "Smoothing factor. 100% = no smoothing, 15% = maximum smoothing." log_style_on2 = "Enables SDcard datalogging.\nAlways - log always.\nButton - use a button to start and stop logs.\nTrigger - start logs when trigger condition is met." log_style2_but = "Digital switch input." log_style4_opt = "Type of trigger to start logging." log_trig_rpm = "Start logging above this RPM." log_trig_tps = "Start logging above this TPS." log_style_led = "Output for LED or indicator lamp." log_style_block = "Type of datalog to record.\n64byte = regular SDcard datalog.\n64byte+stream = datalog plus simulataneous audio soundtrack." log_style2_samp = "Timed = suitable for all installs.\nCycle/tooth = for developer use." log_int = "How often to record data.\nLower limit for most cards is 3ms." log_length = "How long each datalog file should be. After this time a new logfile is started." log_style3_adc = "Optional analogue (sound) stream input." log_style_ledspd = "Unless advised otherwise, use 'Normal'" log_style_gps = "Enables the recording of interleaved GPS data.\n\nRequires a CAN connected GPS module." egt_num = "Number of EGT channels to enable." egtcal_temp0 = "Temperature at 0V." egtcal_tempmax = "Temperature at 5V - depends on interface design." egt_conf_action = "EGT over-temperature reactions" egt_warn = "Turn on warning output above this temperature." egt_addfuel = "Bump up pulsewidth on over-temperature." egt_conf_bank = "Most installs should use 'Both' Bank1,2 only apply to Staged primary and secondaries." egt_conf_shutdown = "Enables engine shutdown if above max temperature or too long above warning limit." egt_time = "Shutdown if above warning temperature for this long." egt_max = "Shutdown if temperature exceeds this maximum (even for a split second.)" egt1port = "Analogue 0-5V input from thermocouple. (Note that an interface circuit is required.)" sensor01_source = "Analogue 0-5V input." sensor01Alias = "User defined name assigned to this sensor input. e.g. pre-intercooler air temperature." sensor01_trans = "Type of transformation from raw input to useful numbers.\nRaw = raw 0-1023 ADC count\nLinear = useful for many ratiometric sensors with a linear scale.\nSame as XXX applies the same transform as other sensors on your ECU.\nGM calibration = same transform as GM air/coolant thermistor sensors." sensor01_val0 = "The number you want to see when 0V is applied" sensor01_max = "The number you want to see when 5V is applied" sensor01LF = "Smoothing factor. 100% = no smoothing, 15% = maximum smoothing." opt142_gs_share = "Normally each input can only be used by one feature. This setting allows inputs to be shared between generic sensors and other features. (Obviously you can still only connect one sensor to each input!)" sensor_temp = "Selects degF/degC for temperature units when using CLT/MAT calibrations. This is set on the Generic Sensors page." tc_opt_on = "Enables traction control" tc_opt_method = "Traction control method:\nPerfect Run = a drag race strategy for a single pass comparing actual VSS against best possible.\nVSS %slip = compares VSS1 to VSS2 and detects slip%.\nPerfect Run RPM = similar to perfect run but without VSS for classes where that is not allowed.\nSwitch input = for use with an external slip detector." tc_enin = "Optional digital switch input" tc_mintps = "Only enable traction control above this TPS%" tc_minmap = "Only enable traction control above this MAP" tc_minvss = "Only enable traction control above this VSS" tc_opt_slipcurve = "Whether to use a fixed slip% limit or an adjustable curve." tc_slipthresh = "Fixed slip% limit." tc_opt_n2o = "Only on/off control is presently supported." tc_opt_bank = "Which bank of injectors to add fuel to.\nNormally select 'Both'\nWhen staging bank 1 = primary, bank 2 = secondary" launch_opt_on = "Off - all of launch is turned off\nLaunch - launch only, no flat shift\nLaunch/flatshift - launch and flat shift.\n(Flat shift is used on manual gearboxes for full throttle shifts with a clutch switch to engage the limiter.)" launch_opt_vss = "Enables wheel speed based launch instead of switch input. Select the wheel-speed sensor for a non-driven wheel." launch_opt_pins = "Input for launch switch." launch_sft_zone = "The soft limit is this many rpm below the hard limit. (This is sometimes called the control range.) 200rpm is typical." launch_sft_deg = "The absolute timing to retard to. i.e. 5 gives 5 BTDC timing." launch_opt_bank = "Allows fuelling to be changed while the launch limiter is on." launch_addfuel = "The raw millisecond pulsewidth change to make (+/-)" launch_tps = "Launch is only active when the throttle is open a certain percentage. Most users can safely set this to a very low number." launch_hrd_lim = "Above this rpm the hard limiter methods are used when the launch conditions are met." launchlimopt = "-None - do not use \n-Spark cut - drop sparks, this is the most common limiter used. (Will not work with EDIS ignition.)\n-Fuel cut - cuts fuel.\n-Spark and fuel - both" launchvsstime = "Once you have been moving for this number of seconds, VSS based launch control is locked out until next stop.\nSet to zero to make it permanently active (no timeout.)" launch_fcut_rpm = "During the flat-shift up-shift and the revs are falling, the fuel is cut off until the revs have fallen below this set point to reduce exhaust explosions." launch_maxvss = "Prevents launch from activating once you are rolling." launchvss_minvss = "Below this speed the wheel speed launch is re-armed.\n\nTypically set to a very low number." launch_opt_vssgear = "Enables/disables checking of gear no.\n\n(Requires gear detection to be enabled.)" launchvss_maxgear = "Wheel speed launch is applied up to this gear number.\n\ne.g. 2 means launch can be used in 1st and 2nd." flats_minvss = "Prevents flat-shift from activating at low speeds e.g. just after launch" flats_arm = "This rpm set point is used to differentiate between a flat shift and launch condition, typically set to a few hundred RPM above idle." flats_deg = "The absolute timing to retard to. i.e. 5 gives 5 BTDC timing." flats_hrd = "Above this rpm the hard limiter methods are used when the flat-shift conditions are met." launch_opt_retard = "Enables feature to feed in timing after launch." launch_var_on = "Input for 0-5V potentiometer used to vary launch RPM." launch_var_low = "With a 0V input, the launch hard limit is set to this RPM." launch_var_up = "With a 5V input, the launch hard limit is set to this RPM." launch_3step_in = "Input for 3-step switch. Could be used as burnout limiter." launch_sft_deg3 = "The timing is retarded to this angle when the 3-step is on." launch_hrd_lim3 = "Sets the hard limit RPM when the 3-step is on." timedout1_in = "Input for transbrake button." timedout1_out = "Output for transbrake solenoid." timedout1_offdelay = "Delay between button release and transbrake release." tcs_in = "Input for Turbo Staging control" tcs_offtime = "How long to release trans-brake for on each move step. This should be set long enough to move the car a little without gaining any speed." tcs_ontime = "How long the trans-brake should be re-activated for between each step. This should be set long enough to fully grab again." tcs_moves = "How many moves (trans-brake release steps) on the first press of the button. Each subsequent press of the button gives a single move." tstop_out = "Output for throttle-stop solenoid." tstop_delay = "Delay after launch before solenoid is activated." tstop_hold = "How long to keep solenoid on for." N2Oopt_2 = "Enables the feature." N2ORpm = "The minimum RPM to enable nitrous." N2OClt = "The minimum coolant temperature to enable nitrous." N2OTps = "The minimum throttle position to enable nitrous." N2ORpmMax = "The maximum RPM to enable nitrous." N2Oopt_01 = "Set to 'Both' for most installs. If 'dual table' or Staging are in use it selects which injector bank receives any additional fuel pulsewidth." N2Oopt2_prog = "Selects between On/Off or Progressive control mode." N2Oopt2_prog_time = "Chooses between time or RPM as control factor." N2Oopt2_prog_freq = "Selects solenoid frequency. Typically around 13Hz." N2Oopt_4 = "Allows optional AFR safety system to use alternate AFR targets when nitrous is active." n2o1n_pins = "Output for stage 1 nitrous solenoid." n2o1f_pins = "Output for stage 1 fuel solenoid." N2Oopt_pins = "Input to use to enable the nitrous system. (Expects a 12V signal.)" N2OPWLo = "Fuel PW to add at the min RPM. (Tapers down between min and max.)" N2OPWHi = "Fuel PW to add at the max RPM. (Tapers down between min and max.)" N2OAngle = "Sets a fixed ignition retard when nitrous is active." N2Odel_launch = "Sets a minimum time after launch control is released before nitrous can activate." N2Odel_flat = "Sets a minimum time after flat-shift is released before nitrous can activate." N2Oopt_3 = "Enables the second stage." n2o2n_pins = "Output for stage 2 nitrous solenoid." n2o2f_pins = "Output for stage 2 fuel solenoid." N2O2Rpm = "The activation RPM for stage 2." N2O2RpmMax = "The maximum RPM for stage 2." N2O2delay = "Sets a minimum time delay after stage 1 activates before stage 2 can activate." N2O2Angle = "Sets an additional ignition retard when stage2 is active." N2O2PWLo = "Fuel PW to add at the min RPM. (Tapers down between min and max.)" N2O2PWHi = "Fuel PW to add at the max RPM. (Tapers down between min and max.)" water_freq_on = "Enables the feature." water_pins_pump = "Output to pump relay." water_freq_type = "'Off' - no valve output (used fixed nozzle)\n'Slow' - slow speed valve output with chosen PWM duty cycle\n'Fast' - valve switches at injector speed with chosen PWM duty cycle." water_freq = "Valve operating frequency." water_pins_valve = "Output for valve." water_tps = "Only enable above this TPS%." water_rpm = "Only enable above this RPM." water_map = "Only enable above this MAP." water_mat = "Only enable above this MAT." water_pins_in_shut = "Allows a low fluid level sensor switch input.\n\nThe switch must be wired so that the input is grounded when the level is ok and no connection is made in low or fault conditions.\n\nIf fluid reserve is low when water injection is required, for safety the engine will be shutdown using the parameters in the AFR Safety System." oilpress_in = "Sensor channel used for oil pressure input." oilpress_out = "Output for warning lamp." fp_drop_load = "Only check for low pressure above this engine load (e.g. MAP, TPS, MAFload)" fp_drop_rpm = "Only check for low pressure above this RPM." fp_drop_psig = "Allowed drop in pressure below target." fp_drop_kpag = "Allowed drop in pressure below target." fp_drop_time = "If fuel pressure stays too low for more than this time, the engine is shutdown using the AFR safety settings." pwm_opt_on_a = "Enables Generic PWM feature.\n\nA table or curve is used to plot the desired output based on a lookup from the input variables." pwm_opt2_a = "Output for relay/solenoid." pwm_opt_freq_a = "Selects:\nOn-Off - output is turned on or off based on the table/curve.\nVariable frequency - output runs at the frequency set by the table/curve with 50% duty.\nxxHz - output runs at a fixed frequency with duty set by the table/curve." pwm_onabove_a = "Output is on when the table/curve is above this number." pwm_offbelow_a = "Output is off when the table/curve is below this number." pwm_opt_load_a = "The variable used for the load axis on the table/curve." pwm_opt_curve_a = "Chooses between a 3D mapped table or a 2D curve." pwm_opt_on_b = "Enables Generic PWM feature.\n\nA table or curve is used to plot the desired output based on a lookup from the input variables." pwm_opt2_b = "Output for relay/solenoid." pwm_opt_freq_b = "Selects:\nOn-Off - output is turned on or off based on the table/curve.\nVariable frequency - output runs at the frequency set by the table/curve with 50% duty.\nxxHz - output runs at a fixed frequency with duty set by the table/curve." pwm_onabove_b = "Output is on when the table/curve is above this number." pwm_offbelow_b = "Output is off when the table/curve is below this number." pwm_opt_load_b = "The variable used for the load axis on the table/curve." pwm_opt_curve_b = "Chooses between a 3D mapped table or a 2D curve." pwm_opt_on_c = "Enables Generic PWM feature.\n\nA table or curve is used to plot the desired output based on a lookup from the input variables." pwm_opt2_c = "Output for relay/solenoid." pwm_opt_freq_c = "Selects:\nOn-Off - output is turned on or off based on the table/curve.\nVariable frequency - output runs at the frequency set by the table/curve with 50% duty.\nxxHz - output runs at a fixed frequency with duty set by the table/curve." pwm_onabove_c = "Output is on when the table/curve is above this number." pwm_offbelow_c = "Output is off when the table/curve is below this number." pwm_opt_load_c = "The variable used for the load axis on the table/curve." pwm_opt_curve_c = "Chooses between a 3D mapped table or a 2D curve." pwm_opt_on_d = "Enables Generic PWM feature.\n\nA table or curve is used to plot the desired output based on a lookup from the input variables." pwm_opt2_d = "Output for relay/solenoid." pwm_opt_freq_d = "Selects:\nOn-Off - output is turned on or off based on the table/curve.\nVariable frequency - output runs at the frequency set by the table/curve with 50% duty.\nxxHz - output runs at a fixed frequency with duty set by the table/curve." pwm_onabove_d = "Output is on when the table/curve is above this number." pwm_offbelow_d = "Output is off when the table/curve is below this number." pwm_opt_load_d = "The variable used for the load axis on the table/curve." pwm_opt_curve_d = "Chooses between a 3D mapped table or a 2D curve." pwm_opt_on_e = "Enables Generic PWM feature.\n\nA table or curve is used to plot the desired output based on a lookup from the input variables." pwm_opt2_e = "Output for relay/solenoid." pwm_opt_freq_e = "Selects:\nOn-Off - output is turned on or off based on the table/curve.\nVariable frequency - output runs at the frequency set by the table/curve with 50% duty.\nxxHz - output runs at a fixed frequency with duty set by the table/curve." pwm_onabove_e = "Output is on when the table/curve is above this number." pwm_offbelow_e = "Output is off when the table/curve is below this number." pwm_opt_load_e = "The variable used for the load axis on the table/curve." pwm_opt_curve_e = "Chooses between a 3D mapped table or a 2D curve." pwm_opt_on_f = "Enables Generic PWM feature.\n\nA table or curve is used to plot the desired output based on a lookup from the input variables." pwm_opt2_f = "Output for relay/solenoid." pwm_opt_freq_f = "Selects:\nOn-Off - output is turned on or off based on the table/curve.\nVariable frequency - output runs at the frequency set by the table/curve with 50% duty.\nxxHz - output runs at a fixed frequency with duty set by the table/curve." pwm_onabove_f = "Output is on when the table/curve is above this number." pwm_offbelow_f = "Output is off when the table/curve is below this number." pwm_opt_load_f = "The variable used for the load axis on the table/curve." pwm_opt_curve_f = "Chooses between a 3D mapped table or a 2D curve." mycan_id = "Set to 0 unless specifically wanting to configure this as a secondary data capture ECU." enable_pollPWM = "Enables capturing PWM (pulse/frequency) from expansion board." can_poll_id = "CANid of expansion board." poll_tablePWM = "Table number on expansion board." poll_offsetPWM= "Table number on expansion board." canpwm_clk = "Clock frequency on expansion board. See documentation." canpwm_pre = "Prescaler on expansion board. See documentation." canpwm_div = "Divider on expansion board. See documentation." enable_pollADC= "Enables capturing analogue inputs from expansion board." canadc_opt1 = "Enables this group of analogue inputs." canadc_id1 = "CANid of expansion board." canadc_tab1 = "Table number on expansion board." canadc_off1 = "Data offset on expansion board." can_poll_id_ports = "CANid of expansion board for digital inputs/outputs." poll_tableports = "Table number on expansion board." enable_pollports_digin = "Enables using digital inputs from expansion board." can_poll_digin_offset = "Data offset on expansion board." enable_pollports_digout = "Enables using on/off outputs on expansion board." can_poll_digout_offset = "Data offset on expansion board." enable_pwmout = "Enables sending PWM/pulsed outputs to expansion board." enable_pwmout255 = "Forces PWM duty cycle to 0-255 range.\ne.g. generic PWMs operate on a 0-100 scale, but your remote device might require a 0-255 scale." can_pwmout_id = "CANid of expansion board." can_pwmout_tab = "Table number on expansion board." can_pwmout_offset = "Data offset on expansion board." can_bcast1_on = "Enables broadcasting of parameters over CAN." can_bcast_int = "How often to broadcast." can_bcast1_280x4 = "Specific messages can be enabled." can_enable_on = "Master enable/disable for all CAN polling and broadcasting." vss1_can_id = "CANid of expansion board." vss1_can_table = "Table number on expansion board." vss1_can_offset = "Data offset on expansion board." vss1_can_size = "How the data is stored on the expansion board. See documentation." vss2_can_offset = "Data offset on expansion board." vss2_can_size = "How the data is stored on the expansion board. See documentation." gear_can_offset = "Data offset on expansion board." opt142_rtc = "Enables the optional on-board real time clock or selects a clock on an expansion board via CAN." rtc_trim = "Applies a trim to correct for slow/fast running clock." can_poll_id_rtc = "CANid of expansion board." poll_table_rtc = "Table number on expansion board." poll_offset_rtc = "Data offset on expansion board." can_poll2_ego = "Enables collecting EGO/AFR from innovate widebands on expansion board." can_ego_id = "CANid of expansion board." can_ego_table = "Table number on expansion board." can_ego_offset = "Data offset on expansion board." can_poll2_gps = "Whether to enable CAN polling for GPS data." can_gps_id = "CANid of expansion board." can_gps_table = "Table number on expansion board." can_gps_offset = "Data offset on expansion board." cel_opt_on = "Enables sensor checking feature." cel_port = "Output for warning lamp.\nIt is STRONGLY SUGGESTED that a lamp be connected when the CEL feature is used." cel_opt_flash = "Selects whether CEL lights up solidly or flashes codes to aid diagnostics.\n\nNumber of flashes and fault:\n2=MAP 3=MAT 4=CLT 5=TPS 6=BATT 7=AFR0 8=SYNC 9=EGT 10=FLEX 11=MAF 12=KNOCK 13=CAM 14=OIL 15=FUELPRESS 16=EGTSHUT 17=AFRSHUT" cel_opt_when = "Do you want the light on when the engine is off?" cel_runtime = "Period after-start before sensors are checked." cel_opt2_map = "Enables checking of the MAP sensor." map_minadc = "Minimum raw ADC 0-1023 input allowed." map_maxadc = "Maximum raw ADC 0-1023 input allowed." map_var_lower = "Minimum amount of fluctuation allowed. (To detect flat-lined input.)" map_var_upper = "Maximum amount of fluctuation allowed. (To detect wildly varying input.)" cel_opt2_mat = "Enables checking of the MAT sensor." mat_minadc = "Minimum raw ADC 0-1023 input allowed." mat_maxadc = "Maximum raw ADC 0-1023 input allowed." mat_var_upper = "Maximum amount of fluctuation allowed. (To detect wildly varying input.)" cel_opt2_clt = "Enables checking of the CLT sensor." clt_minadc = "Minimum raw ADC 0-1023 input allowed." clt_maxadc = "Maximum raw ADC 0-1023 input allowed." clt_var_upper = "Maximum amount of fluctuation allowed. (To detect wildly varying input.)" cel_opt2_tps = "Enables checking of the TP sensor." tps_minadc = "Minimum raw ADC 0-1023 input allowed." tps_maxadc = "Maximum raw ADC 0-1023 input allowed." tps_var_upper = "Maximum amount of fluctuation allowed. (To detect wildly varying input.)" cel_opt2_batt = "Enables checking of the battery voltage input." batt_minv = "Minimum voltage allowed." batt_maxv = "Maximum voltage allowed." batt_var_upper = "Maximum amount of fluctuation allowed. (To detect wildly varying input.)" cel_opt2_afr0 = "Enables checking of the EGO/AFR input." afr_min = "Minimum AFR allowed." afr_max = "Maximum AFR allowed." afr_var_lower = "Minimum amount of fluctuation allowed. (To detect flat-lined input.)" afr_var_upper = "Maximum amount of fluctuation allowed. (To detect wildly varying input.)" cel_opt2_sync = "Enables checking for sync-losses." cel_synctol = "Set CEL above this many sync-losses." cel_opt2_egt = "Enables checking of the EGT input." egt_minvalid = "Minimum EGT allowed." egt_maxvalid = "Maximum EGT allowed." egt_var_lower = "Minimum amount of fluctuation allowed. (To detect flat-lined input.)" egt_var_upper = "Maximum amount of fluctuation allowed. (To detect wildly varying input.)" cel_opt3_flex = "Enables checking of the Flex-fuel sensor input." cel_opt_adc = "Sets gauge 'status5' to record 'fluctuations' number or raw ADC count for the chosen sensor input." cel_opt_stat = "Selects input for 'status5' value. Observe the dash gauge and examine datalogs to determine sensible min/max fluctuation limits and ADC counts for each sensor input in turn." cel_action1_map = "Whether an invalid MAP reading will trigger limp mode." cel_action1_map_an = "Whether an invalid MAP reading will enable the fallback MAP table." cel_action1_mat = "Whether an invalid MAT reading will trigger limp mode." cel_mat_default = "If MAT fails, assume MAT is this temperature." cel_action1_clt = "Whether an invalid CLT reading will trigger limp mode." cel_clt_cold = "If CLT fails, start engine using this assumed temperature." cel_clt_warm = "If CLT fails, assume this is the warmed up engine temperature." cel_warmtime = "If CLT fails, assume engine takes this long to warmup." cel_action1_tps = "Whether an invalid TPS reading will trigger limp mode." cel_action1_batt = "Whether an invalid battery voltage reading will trigger limp mode." cel_action1_ego = "Whether an invalid AFR/EGO reading will trigger limp mode." cel_action2_flex = "Whether an invalid Flex-fuel reading will trigger limp mode." cel_action2_egt = "Whether an invalid EGT reading will trigger limp mode." cel_revlim = "Rev limiter when in limp mode." cel_overboost = "Maximum boost when in limp mode. Typically 102kPa for no boost." cel_boost_duty = "Fixed boost valve duty in limp mode. Set for least boost, typically 0%." cel_boost_duty2 = "Fixed boost valve duty in limp mode. Set for least boost, typically 0%." cel_retard = "Retard timing by this amount when in limp mode." testint = "How often to pulse the coil/injector." testrpm = "Approximate equivalent RPM." testop_coil = "Whether to test a single coil output or operate in sequence." testsel_coil = "Whether to test a single coil output or operate in sequence." testdwell = "Dwell used during testing - no voltage correction is applied." testop_inj = "Whether to test a single injector output or operate in sequence." testsel_inj = "Whether to test a single injector output or operate in sequence." testpw = "Pulsewidth used during testing - no dead-time is added and no voltage correction is applied." testinjcnt = "Number of injection pulses in each test." testop_pwm = "Allows testing of different PWM current limiting parameters." testinjPwmP = "The PWM duty cycle." testinjPwmT = "The full-current time at the beginning of each pulse." testinjPwmPd = "The PWM period aka. frequency." pwm_testio = "Frequency of pulsed outputs." duty_testio = "Duty cycle of pulsed outputs." iachometest = "Number of steps to move valve in homing operation (should be set larger than total number of steps from open to closed.)" iacpostest = "Desired valve position." feature3_pw4x = "Only used on low-revving large engines for extra-long pulsewidths. MUST also set PW4X in Project Properties." feature3_n2oin = "Normally this should be on so that the input responds to a +12V signal. Ensure the JP8 is NOT installed on the MS3X card." fuelcalctime = "How often to perform fuel consumption calculations." RotarySplitModeFD = "FC mode = combined trailing coil for two trailing plugs.\nFD mode = individual coils for each trailing plug." RotarySplitModeNeg = "Split usually fires trailing coils after leading coils, this allows for the split to be negative and the trailing coils to fire before the leading." dwelltime_trl = "Dwell time applied to trailing coil(s)." ;curves help text oil_press_min = "For each RPM setting, set the min and max oil pressures allowed at that RPM.\nOutside of the limits the warning light will be illuminated.\nIt is suggested that the first row be 0 RPM. Set the Min and Max limits above 0 so that the oil warning light is tested on each start." hpte_afrs = "The curve specifies AFR decrease (richer) vs. time.\nIt is normal for the first row to be 0, 0.\nThe second row typically specifies when the enrichment should begin. e.g. 7, 0. This means that there is no change from 0-7 seconds as both are set to a 0 decrease in AFR.\nThe third row onwards specify the richening." fp_temp_adj = "Specifies a percentage adjustment in fuelling based on fuel temperature. 0% means no adjustment." fp_press_adj = "Specifies a percentage adjustment in fuelling based on fuel pressure. 0% means no adjustment.\nThe pressure used for the lookup is always the pressure across the injector i.e. rail pressure - intake pressure." dualfuel_temp_adj = "Specifies a percentage adjustment in fuelling based on fuel temperature. 0% means no adjustment." dualfuel_press_adj = "Specifies a percentage adjustment in fuelling based on fuel pressure. 0% means no adjustment.\nThe pressure used for the lookup is always the pressure across the injector i.e. rail pressure - intake pressure." fpd_duty = "The values in the table specify the duty cycle percent of the control output to the pump or controller based on the RPM/load axes." alt_dutyout = "This allows for non-linear control within alternators. It also allows you to restrict the output duty range." alternator_targvolts = "Specifies the target charge voltage related to the battery temperature.\nOnly works if you have a battery temperature sensor." alternator_dutyv = "Specifies the control duty to achieve the desired voltage." alternator_freqv = "Specifies the control frequency to achieve the desired voltage." pwm_duties_a = "The values within the table specify the output duty or frequency based that is looked up based on the input 'load' and RPM." pwm_duties_b = "The values within the table specify the output duty or frequency based that is looked up based on the input 'load' and RPM." pwm_duties_c = "The values within the table specify the output duty or frequency based that is looked up based on the input 'load' and RPM." pwm_duties_d = "The values within the table specify the output duty or frequency based that is looked up based on the input 'load' and RPM." pwm_duties_e = "The values within the table specify the output duty or frequency based that is looked up based on the input 'load' and RPM." pwm_duties_f = "The values within the table specify the output duty or frequency based that is looked up based on the input 'load' and RPM." pwm_yaxis_a = "Specifies the output duty or frequency based on the input 'load' value." pwm_yaxis_b = "Specifies the output duty or frequency based on the input 'load' value." pwm_yaxis_c = "Specifies the output duty or frequency based on the input 'load' value." pwm_yaxis_d = "Specifies the output duty or frequency based on the input 'load' value." pwm_yaxis_e = "Specifies the output duty or frequency based on the input 'load' value." pwm_yaxis_f = "Specifies the output duty or frequency based on the input 'load' value." tcslipy = "Sets the desired slip% threshold at different knob settings 0-100%" tc_knob = "This enables a link to a Generic Sensor input to enable you to set the slip threshold. Configure the Generic Sensor to give 0-100 as the linear output." blendy1 = "Sets a percentage blend from VE1 (0%) to VE2 (100%) based on the input X axis value." blendy2 = "Sets a percentage blend from Spk1 (0%) to Spk2 (100%) based on the input X axis value." blendy3 = "Sets a percentage blend from the combined VE1+2 (0%) to VE3+4 (100%) based on the input X axis value." blendy4 = "Sets a percentage blend from the combined Spk1+2 (0%) to Spk3+4 (100%) based on the input X axis value." blendy5 = "Sets a percentage blend from AFR1 (0%) to AFR2 (100%) based on the input X axis value." blendy6 = "Sets a percentage blend from Boost1 (0%) to Boost2 (100%) based on the input X axis value." blendy7 = "Sets a percentage blend from Cranking Pulse1 (0%) to Cranking Pulse2 (100%) based on the input X axis value." tpswot_tps = "Sets the TPS% that is considered wide-open-throttle based on RPM.\ni.e. at low RPMS, partial throttle will flow the same air as full throttle. At maximum RPMs full throttle is required for full air flow.\nWhen the throttle is at or beyond the new 'full throttle' it is considered 100% throttle. This has the effect of making TPS based accel enrichment more sensitive at lower throttle opening at lower RPMs and also prevents TPS accel enrichment if the throttle is already 'fully open.'" launch_retard = "The curve sets the degrees of ignition subtracted from the normal timing (i.e. retarding it) against time after launch.\nThis can be used to launch at higher RPMs without blowing the tyres away and then feeding the timing back in.\nBe sure to end the curve with zero degrees of retard to use normal timing for the rest of the run." cl_idle_timing_advance_deltas = "Uses timing to assist closed-loop idle control.\nThe X axis of the curve is RPMs +/- the target. i.e. if the target was 800, then -75 in the curve means 800-75 = 725RPM\nThe Y axis of the curve is timing +/-. i.e. + means add timing, - means subtract timing.\nTypically, use positive (advanced) timing when RPMs are below target and negative (retarded) timing when RPMs are above target." idle_voltage_comp_delta = "Some 2 wire PWM idle valves will operate differently depending on the system voltage. This allows a compensation to be applied to allow for that difference.\nTypically at lower voltages the valve will need slightly more duty (positive number) and at higher voltages it will need less duty (negative number.)" maeBins = "The curve specifies a fuel pulsewidth percent adder based on rate of change of MAP (MAPdot)\nThis is part of the basic time based accel enrichment scheme. Larger changes in MAP require more fuel added. The number is a percentage of ReqFuel." taeBins = "The curve specifies a fuel pulsewidth percent adder based on rate of change of TPS (TPSdot)\nThis is part of the basic time based accel enrichment scheme. Larger changes in TPS require more fuel added. The number is a percentage of ReqFuel." accel_mapdot_amts = "The curve specifies a fuel pulsewidth percent adder based on rate of change of MAP (MAPdot)\nThis is part of the accel-pump based accel enrichment scheme. Larger changes in MAP require more fuel added.\nThe negative part of the curve is used for decel enleanment, or set to zero PW% for no enleanment.\nEnsure that there is a 0 0 point in the curve so that when MAP is not changing, no additional fuel is added. The number is a percentage of ReqFuel." accel_tpsdot_amts = "The curve specifies a fuel pulsewidth percent adder based on rate of change of TPS (TPSdot)\nThis is part of the accel-pump based accel enrichment scheme. Larger changes in TPS require more fuel added.\nThe negative part of the curve is used for decel enleanment, or set to zero PW% for no enleanment.\nEnsure that there is a 0 0 point in the curve so that when TPS is not changing, no additional fuel is added. The number is a percentage of ReqFuel." knock_starts = "Set the crank angle (for each cylinder) when the knock system starts 'listening' for knock.\nKnock usually occurs in the time after TDC." knock_durations = "Set the number of crank degrees that the knock system 'listens' for knock." knock_thresholds = "Sets an allowable knock level before retard is triggered.\nThe numbers here are highly engine dependent." knock_upscale = "Allows the threshold to be scaled up on a cold engine. Frequently a cold engine is noiser and may cause false alarms without a raised threshold." tc_perfect_vss = "The perfect run traction control sets a curve of the 'best' speed (VSS) that you can run for each time-point after launch.\nIf your VSS is reporting a higher number than the curve, it is assumed to be wheelspin and the reactions come into force.\nThis traction control strategy is typically applied early in a run only.\nNote that VSS based traction control is outlawed in some race classes." tc_perfect_rpm = "The perfect run traction control sets a curve of the 'best' RPM that you can run for each time-point after launch.\nIf your RPM is higher than the curve, it is assumed to be wheelspin and the reactions come into force.\nThis traction control strategy only makes sense in first gear. Set the final row in the table to just earlier than the time when you expect to shift with an RPM higher than your maximum RPM." tc_retard = "Sets the number of degrees of timing retard to apply based on the amount of wheelspin multiplied by how long." tc_spkcut = "Sets the amount of spark cut to apply based on the amount of wheelspin multiplied by how long." tc_nitrous = "Sets the amount of nitrous cut to apply based on the amount of wheelspin multiplied by how long." tc_boost = "Sets the amount to reduce the boost target by based on the amount of wheelspin multiplied by how long." tc_boost_duty_delta = "Sets the amount to change the boost duty by based on the amount of wheelspin multiplied by how long." tc_addfuel = "Sets the amount of fuel to add based on the amount of wheelspin multiplied by how long." primePWTable = "The priming pulse is used to wet the intake manifold walls and provide some initial starting fuel.\nSetting the curve to all zeros will disable fuel pump priming also." primePWTable2 = "The priming pulse is used to wet the intake manifold walls and provide some initial starting fuel.\nSetting the curve to all zeros will disable fuel pump priming also." crankPctTable = "This percentage table controls the fuel injected when the engine is cranking over. Most engines need 200-400% when cold and near 100% when hot.\n(It is a percentage of ReqFuel, so that if you swap injectors, this curve can be left alone.)" crankPctTable2 = "This percentage table controls the fuel injected when the engine is cranking over. Most engines need 200-400% when cold and near 100% when hot.\n(It is a percentage of ReqFuel, so that if you swap injectors, this curve can be left alone.)" asePctTable = "Immediately after the engine has started it is normal to need additional fuel. This curve specifies how much as a percentage adder. (5-50%)" asePctTable2 = "Immediately after the engine has started it is normal to need additional fuel. This curve specifies how much as a percentage adder. (5-50%)" aseCntTable = "Specifies how long (in engine cycles or seconds) to apply afterstart enrichment." aseCntTable2 = "Specifies how long (in engine cycles or seconds) to apply afterstart enrichment." wueBins = "Specifies the percentage multiplier for fuel during warmup. At cold temperatures 200-300% may be required. At fully warm (final row in table) 100% MUST be specified.\n(LPG users can override this requirement by turning off the warmup warning on the gauge settings/limit page.)" wueBins2 = "Specifies the percentage multiplier for fuel during warmup. At cold temperatures 200-300% may be required. At fully warm (final row in table) 100% MUST be specified.\n(LPG users can override this requirement by turning off the warmup warning on the gauge settings/limit page.)" mafflow = "Specifies the flow curve in grammes/sec vs. frequency or voltage.\nStart out with the actual flow curve for your MAF sensor and then 'tweak' to tune it to your install." MAFCor = "Specifies the adjustment on top of the MAF sensor calibration you loaded through Tools-Calibrate MAF table\nStart out with the correction curve at 100% (no correction) and then 'tweak' to tune it to your install." dwellrpm_dwell = "For Saab Trionic ignition, this allows the dwell time to be varied with RPM." boostvss_duty = "For open-loop boost control, this specifies a solenoid duty based on the wheel speed on VSS1 or VSS2." boostvss_target = "For closed-loop boost control, this specifies a target boost level based on the wheel speed on VSS1 or VSS2.\nThis can be used to limit boost in lower gears to reduce the change of wheelspin or loss of control." n2o1_duty = "For progressive control, this specifies the solenoid duty vs. active time or RPM." n2o2_duty = "For progressive control, this specifies the solenoid duty vs. active time or RPM." n2o1_pw = "For progressive control, this specifies the additional fuel pulsewidth vs. active time or RPM." n2o2_pw = "For progressive control, this specifies the additional fuel pulsewidth vs. active time or RPM." n2o1_retard = "For progressive control, this specifies the ignition retard vs. active time or RPM." n2o2_retard = "For progressive control, this specifies the ignition retard vs. active time or RPM." matclt_pct = "The curve is the %CLT blended into the MAT reading vs. airflow.\nIn theory, at zero air-flow the air temperature in the intake manifold will reach the manifold (coolant) temperature. At infinite airflow, the air will be unaffected by the temperature of the manifold.\nThe curve is setup to give the 'best estimate' of intake air temperature as part of the speed-density fuel calculation.\nIt would be expected that some CLT should be blended in at low airflows, falling away rapidly to close to zero at higher airflows.\nWhen first enabling this curve it will be necessary to adjust the VE values at low RPMs as they will be compensating for the air density change." smallpw0 = "This allows for some correction to the non-linearity that fuel injectors show at low pulsewidths.\nTesting has shown that injectors are frequently linear by 2ms, but below than require more actual pulsewidth than linear to achieve the desired fuel flow.\ne.g. for '1.0ms' of fuel, 1.5ms PW may actually be required." smallpw1 = "This allows for some correction to the non-linearity that fuel injectors show at low pulsewidths.\nTesting has shown that injectors are frequently linear by 2ms, but below than require more actual pulsewidth than linear to achieve the desired fuel flow.\ne.g. for '1.0ms' of fuel, 1.5ms PW may actually be required." smallpw2 = "This allows for some correction to the non-linearity that fuel injectors show at low pulsewidths.\nTesting has shown that injectors are frequently linear by 2ms, but below than require more actual pulsewidth than linear to achieve the desired fuel flow.\ne.g. for '1.0ms' of fuel, 1.5ms PW may actually be required." smallpw3 = "This allows for some correction to the non-linearity that fuel injectors show at low pulsewidths.\nTesting has shown that injectors are frequently linear by 2ms, but below than require more actual pulsewidth than linear to achieve the desired fuel flow.\ne.g. for '1.0ms' of fuel, 1.5ms PW may actually be required." opentimepct0 = "Specifies the percentage change in injector deadtime vs. system voltage.\n13.2V must be 100%.\nAt lower voltages the deadtime % will be above 100%; at higher voltages it will be below 100%" opentimepct1 = "Specifies the percentage change in injector deadtime vs. system voltage.\n13.2V must be 100%.\nAt lower voltages the deadtime % will be above 100%; at higher voltages it will be below 100%" opentimepct2 = "Specifies the percentage change in injector deadtime vs. system voltage.\n13.2V must be 100%.\nAt lower voltages the deadtime % will be above 100%; at higher voltages it will be below 100%" opentimepct3 = "Specifies the percentage change in injector deadtime vs. system voltage.\n13.2V must be 100%.\nAt lower voltages the deadtime % will be above 100%; at higher voltages it will be below 100%" boost_timed_pct = "Allows boost to be feathered in after launching.\n100% means use normal boost settings." map_sample_timing = "When timed MAP sampling is enabled, this specifies the angle BTDC for each cylinder when MAP sampling should begin.\nExperimentation and use of the Diagnostics-MAP logger will be required to determine the best settings." dwellcorr = "Specifies the percentage adjustment to the nominal dwell based on battery voltage.\nInductive coils require greater dwell (charge time) at lower voltages." cold_adv_table = "This curve optionally allows ignition timing to be advance during warmup.\n Conversely, some engines may prefer retard during warmup to pre-heat the catalytic convertor." iacstepTable = "Specifies the stepper idle 'step' position vs. coolant temperature to be used during warmup.\nLarge positions are more open. Zero is fully closed.\nThe curve will start high at cold temperatures and descend towards zero at high temperatures." ipwmTable = "Specifies the PWM idle duty vs. coolant temperature to be used during warmup.\nLarge duties are more open. Typically zero is fully closed. (Some 2 wire Bosch valves have a closed position of about 35%)\nThe curve will start high at cold temperatures and descend towards zero at high temperatures." matRetard = "Allows ignition timing to be retarded based on intake temperature. This is primarily for forced induction installs where there is charge heating." baroCorrDelta = "There are two ways that barometric correction may be used.\n\n1. The current way. On the MAP/Baro page the 'At total vacuum' and 'rate' numbers must be set to zero. This curve is then normally 100% at all points and adjusted up or down to alter fuelling based on the barometer reading.\n\n2. The old way. The two numbers are set to 147 and -47 and the curve is normally 0% at all points." matCorrDelta2 = "This curve is the whole air density correction exposed in full.\nIt is based on the 'ideal gas law' and typically varies between 125% cold to 75% hot." matCorrDelta = "Allows for minor corrections to fuelling based on manifold air temperature (MAT) when using MAF to control fuelling. The default curve is 0% meaning no correction." EAEAWN2 = "This curve modifies the EAE Adhere-to-walls curve. It allows the amount of correction specified by the EAE Adhere-to-walls curve to be increased or decreased based on RPM." EAEAWN = "This curve modifies the EAE Adhere-to-walls curve. It allows the amount of correction specified by the EAE Adhere-to-walls curve to be increased or decreased based on RPM." EAEAWW2 = "This curve modifies the EAE Adhere-to-walls curve. It allows the amount of correction specified by the EAE Adhere-to-walls curve to be increased or decreased based on coolant temperature." EAEAWW = "This curve modifies the EAE Adhere-to-walls curve. It allows the amount of correction specified by the EAE Adhere-to-walls curve to be increased or decreased based on coolant temperature." EAEBAWC2 = "This curve determines how much fuel is getting added to the port walls per injection event. It is a percentage (Y-axis) of each injection event based on load (X-axis)." EAEBAWC = "This curve determines how much fuel is getting added to the port walls per injection event. It is a percentage (Y-axis) of each injection event based on load (X-axis)." EAEBSOC2 = "This curve determines how much fuel is being sucked from the walls on each intake (valve open) event. It is a percentage (Y-axis) of the total amount of fuel that has adhered to the walls based on load (X-axis), so therefore the percentages are much smaller (about 10x smaller) than the Adhere-to-walls coefficients." EAEBSOC = "This curve determines how much fuel is being sucked from the walls on each intake (valve open) event. It is a percentage (Y-axis) of the total amount of fuel that has adhered to the walls based on load (X-axis), so therefore the percentages are much smaller (about 10x smaller) than the Adhere-to-walls coefficients." EAESON2 = "This curve modifies the EAE Sucked-from-walls curve. It allows the amount of correction specified by the EAE Sucked-from-walls curve to be increased or decreased based on RPM." EAESON = "This curve modifies the EAE Sucked-from-walls curve. It allows the amount of correction specified by the EAE Sucked-from-walls curve to be increased or decreased based on RPM." EAESOW2 = "This curve modifies the EAE Sucked-from-walls curve. It allows the amount of correction specified by the EAE Sucked-from-walls curve to be increased or decreased based on coolant temperature." EAESOW = "This curve modifies the EAE Sucked-from-walls curve. It allows the amount of correction specified by the EAE Sucked-from-walls curve to be increased or decreased based on coolant temperature." XAcc = "This is the percentage of the fuel (0-100%) that goes into the wall puddle while accelerating (fuel pulse width increasing), with the remainder of the squirt going directly into the cylinder to be burned." XDec = "This is the percentage of fuel (0-100%) going into the wall puddle while decelerating (fuel pulse width decreasing)," TauAcc = "This is the time factor vs. RPM used during acceleration." TauDec = "This is the time factor vs. RPM used during deceleration." XClt = "Coolant temperature (CLT) correction to the puddling factor X." TauClt = "Coolant temperature (CLT) correction to the time factor Tau." MapThreshXTD = "X-Tau accel tables are used when MAPdot is positive or less negative than this start transition threshold. In-between a blend is used." MapThreshXTD2 = "X-Tau Decel tables are used when MAPdot is more negative than this finish transition threshold. In-between a blend is used." NoiseFilterLen = "The duration of the noise filter depending on RPM. Its aim is to filter out brief spikes of noise on the tach input. The settings here depend on wheel mode and are engine specific. Setting the filter period too high will filter out real teeth.\nExamples\n36-1, 60-2: 500rpm = 200us, 7500rpm = 13\nBasic crank trigger: 500rpm = 1800us, 7500rpm = 120us" idleadvance_curve = "Sets the timing vs engine load when Idle-Advance is active. Typically the curve will ramp from low advance at low load to more advance at higher loads to stablise idle." pwmidle_target_rpms = "The closed-loop idle RPM target depending on coolant temperature. It is normal to set a high idle on a cold engine, tapering down as the engine warms up." RevLimRpm1 = "When the coolant-based rev-limiter is enabled this allows you to specify different rev limits depending on the coolant temperature to prevent a cold engine from being over-revved." pwmidle_crank_dutyorsteps_duty = "The idle valve position during cranking. This should be set high enough so that the engine can start without touching the throttle when cold, but not so high that the engine revs up too far immediately after starting." pwmidle_crank_dutyorsteps_steps = "The idle valve position during cranking. This should be set high enough so that the engine can start without touching the throttle when cold, but not so high that the engine revs up too far immediately after starting." ITB_load_loadvals = "This curve is used to allocate the bins on the VE table to either Speed-Density or Alpha-N tuning. The area of the VE table below the load value from the curve will be used for Speed-Density tuning and the area above the curve will be used for Alpha-N tuning.\nChanging this curve will require the VE table to be retuned.\nSee the full manual for more details on ITB mode." ITB_load_switchpoints = "This curve defines the TPS value where the MAP load reaches %Baro switchpoint. This curve will be different for each engine and should be set up using values obtained from log files from your engine. Setting this curve is an important part of ITB mode.\nChanging this curve will require the VE table to be retuned.\nSee the full manual for more details on ITB mode." ITB_load_mappoint = "Above this MAP value, tuning switches from MAP based to TPS based. Default is 90% and works for most engines." ITB_load_idletpsthresh = "A minimum TPS value that must be met to allow the switch to TPS based tuning to occur. This is sometimes useful in idle tuning." ; tables ego_auth_table = "Specifies the EGO authority limit across the range of engine operation condition. Setting zero means there will be no change in fuel based on the lambda sensor i.e. open-loop mode. " ltt_table1 = "This read-only table shows the long-term-terim values the ECU has calculated based on lambda sensor feedback." alphaMAPtable = "The best-guess MAP value from an alpha-N (TPS vs. RPM) lookup table. This is primarily used as a fallback in case of MAP sensor failure." pwmidle_cl_initialvalues_duties = "The best-guess idle valve duty for RPM/load. This allows you to 'kick-start' the closed-loop idle by setting the valve to the most likely position." pwmidle_cl_initialvalues_steps = "The best-guess idle valve position for RPM/load. This allows you to 'kick-start' the closed-loop idle by setting the valve to the most likely position." vvt_timing1 = "Desired VVT (relative) timing vs RPM/load" vvt_timing2 = "Desired VVT (relative) timing vs RPM/load" als_rifuelcut = "The fuel-cut percentage vs. RPM/load when in anti-lag idle mode.\nThis must ONLY be used with sequential fuel as it cuts off injectors in a round-robin manner." als_fuelcut = "The fuel-cut percentage vs. RPM/load when in anti-lag mode.\nThis must ONLY be used with sequential fuel as it cuts off injectors in a round-robin manner." als_sparkcut = "The spark-cut percentage vs. RPM/load when in anti-lag mode.\nThis drops sparks in a round-robin manner." als_timing = "The ignition advance vs. RPM/load when in anti-lag mode.\nTypically this will be -20 to -50 for ATDC timing." als_addfuel = "The percentage of fuel to be added vs. RPM/load when in anti-lag mode." waterinj_duty = "The duty cycle of the output vs RPM/load" maxafr1_diff = "The maximum AFR difference allowed on the leaner side. This compares the AFR target table and the wideband lambda sensor reading.\nTypically a larger allowance is allowed under low load and low RPMs. High load and into boost require tight control to guard against engine-damaging lean conditions." veTable1 = "The main fuel table (1). Larger VE values mean more fuel, smaller mean less fuel." veTable2 = "The secondary fuel table (2), can be used as a blend table with table 1. Larger VE values mean more fuel, smaller mean less fuel." veTable3 = "The alternate main fuel table (3). Can be used as a switched table from no.1. Larger VE values mean more fuel, smaller mean less fuel." veTable4 = "The alternate secondary fuel table (4). Can be used as a blended and switched table from no.1+2. Larger VE values mean more fuel, smaller mean less fuel." idleve_table1 = "Sets the VE values when 'idle-VE' is active." idleve_table2 = "Sets the VE values when 'idle-VE' is active." staged_percents = "Percentage values specify the amount of staging.\n0% = not staged, only primaries\n100% = fully staged." afrTable1 = "Sets the target AFR vs RPM/load.\nWhen 'incorporate AFR' is off, this is a reference table only.\nWhen 'incorporate AFR' is on, this table is included in the fuel calculation.\n\nSet this table before beginning tuning." afrTable2 = "Sets the target AFR vs RPM/load.\nWhen 'incorporate AFR' is off, this is a reference table only.\nWhen 'incorporate AFR' is on, this table is included in the fuel calculation.\n\nSet this table before beginning tuning." advanceTable1 = "The main ignition advance table (1). Numbers are actual timing BTDC.\nBe sure to have verified timing before starting tuning." advanceTable2 = "The secondary ignition advance table (2), can be used as a blend table with table 1." advanceTable3 = "The alternate main ignition advance table (3). Can be used as a switched table from no.1" advanceTable4 = "The alternate secondary ignition advance table (4). Can be used as a blended and switched table from no.1+2." RotarySplitTable = "Specifies the split (delay) in degrees between leading and trailing coils." boost_ctl_pwm_targets = "For open-loop boost, sets the output duty cycle vs. TPS/RPM" boost_ctl_load_targets = "For closed-loop boost, sets the target kPa (boost) vs. TPS/RPM" boost_ctl_pwm_targets2 = "For open-loop boost, sets the output duty cycle vs. TPS/RPM" boost_ctl_cl_pwm_targs1 = "The best-estimate boost valve duty for target load vs. RPM. This allows you to 'kick-start' the closed-loop boost by setting the valve to the this position before engaging closed-loop PID control.\n\nThe table is determined by reviewing datalogs or taking a known open-loop table." boost_ctl_cl_pwm_targs2 = "The best-estimate boost valve duty for target load vs. RPM. This allows you to 'kick-start' the closed-loop boost by setting the valve to the this position before engaging closed-loop PID control.\n\nThe table is determined by reviewing datalogs or taking a known open-loop table." boost_ctl_load_targets2 = "For closed-loop boost, sets the target kPa (boost) vs. TPS/RPM" inj_trima = "Specifies a +/- percentage adjustment on the basic fuel pulsewidth to allow for difference per cylinder." inj_trimb = "Specifies a +/- percentage adjustment on the basic fuel pulsewidth to allow for difference per cylinder." inj_trimc = "Specifies a +/- percentage adjustment on the basic fuel pulsewidth to allow for difference per cylinder." inj_trimd = "Specifies a +/- percentage adjustment on the basic fuel pulsewidth to allow for difference per cylinder." inj_trime = "Specifies a +/- percentage adjustment on the basic fuel pulsewidth to allow for difference per cylinder." inj_trimf = "Specifies a +/- percentage adjustment on the basic fuel pulsewidth to allow for difference per cylinder." inj_trimg = "Specifies a +/- percentage adjustment on the basic fuel pulsewidth to allow for difference per cylinder." inj_trimh = "Specifies a +/- percentage adjustment on the basic fuel pulsewidth to allow for difference per cylinder." inj_trimi = "Specifies a +/- percentage adjustment on the basic fuel pulsewidth to allow for difference per cylinder." inj_trimj = "Specifies a +/- percentage adjustment on the basic fuel pulsewidth to allow for difference per cylinder." inj_trimk = "Specifies a +/- percentage adjustment on the basic fuel pulsewidth to allow for difference per cylinder." inj_triml = "Specifies a +/- percentage adjustment on the basic fuel pulsewidth to allow for difference per cylinder." inj_trimm = "Specifies a +/- percentage adjustment on the basic fuel pulsewidth to allow for difference per cylinder." inj_trimn = "Specifies a +/- percentage adjustment on the basic fuel pulsewidth to allow for difference per cylinder." inj_trimo = "Specifies a +/- percentage adjustment on the basic fuel pulsewidth to allow for difference per cylinder." inj_trimp = "Specifies a +/- percentage adjustment on the basic fuel pulsewidth to allow for difference per cylinder." inj_timing = "The injector timing in degrees BTDC vs load/RPM. Typical wisdom says that the injection event should finish just as the inlet valve is opening. This corresponds to around 360 BTDC as the timing is measured with respect to the spark event.\nActual best timing can be determined by dyno or road testing." inj_timing_sec = "The injector timing (for secondary staged injectors) in degrees BTDC vs load/RPM. Typical wisdom says that the injection event should finish just as the inlet valve is opening. This corresponds to around 360 BTDC as the timing is measured with respect to the spark event.\nActual best timing can be determined by dyno or road testing." spk_trima = "Specifies a +/- timing angle adjustment on the basic timing to allow for difference per cylinder." spk_trimb = "Specifies a +/- timing angle adjustment on the basic timing to allow for difference per cylinder." spk_trimc = "Specifies a +/- timing angle adjustment on the basic timing to allow for difference per cylinder." spk_trimd = "Specifies a +/- timing angle adjustment on the basic timing to allow for difference per cylinder." spk_trime = "Specifies a +/- timing angle adjustment on the basic timing to allow for difference per cylinder." spk_trimf = "Specifies a +/- timing angle adjustment on the basic timing to allow for difference per cylinder." spk_trimg = "Specifies a +/- timing angle adjustment on the basic timing to allow for difference per cylinder." spk_trimh = "Specifies a +/- timing angle adjustment on the basic timing to allow for difference per cylinder." spk_trimi = "Specifies a +/- timing angle adjustment on the basic timing to allow for difference per cylinder." spk_trimj = "Specifies a +/- timing angle adjustment on the basic timing to allow for difference per cylinder." spk_trimk = "Specifies a +/- timing angle adjustment on the basic timing to allow for difference per cylinder." spk_triml = "Specifies a +/- timing angle adjustment on the basic timing to allow for difference per cylinder." spk_trimm = "Specifies a +/- timing angle adjustment on the basic timing to allow for difference per cylinder." spk_trimn = "Specifies a +/- timing angle adjustment on the basic timing to allow for difference per cylinder." spk_trimo = "Specifies a +/- timing angle adjustment on the basic timing to allow for difference per cylinder." spk_trimp = "Specifies a +/- timing angle adjustment on the basic timing to allow for difference per cylinder." narrowband_tgts = "The target narrowband lamba sensor voltage vs. load/RPM" vsslaunch_rpm = "RPM specifies the hard limiter RPM for given wheel speed.\nRetard is the retard to ignition advance for given wheel speed.\nWhen wheel speed exceeds maximum speed on curve, the launch control is disabled until speed drops below the re-arm setting." fuelcut_fuelon_upper_rpmdot = "When revs are falling more quickly than this RPMdot value the initial RPM is used for fuel return.\nIn-between upper and lower RPMdot values, the return RPM is interpolated. This number must be larger than the 'lower' RPMdot setting.\nTypically 1000." fuelcut_fuelon_lower_rpmdot = "When revs are falling more slowly than this RPMdot value the lower RPM is used for fuel return. This will happen when coasting down.\nIf revs are falling more quickly then any return transitions will be cancelled and the return RPM will be raised.\n\nSet this so that clutch-in during fuel cut does not stall.\nTypically 500.\n\n(The RPMdot shows negative in datalogs when revs are falling, so a setting of 500 means less negative than -500)" egoAlgorithm_delay_table = "Specifies whether to use IGN events or delay table to determine how often EGO runs" ego_delay_table = "Table which specifies the delay between runs of the EGO algorithm in ms" ego_delay_rpms = "RPM (x) axis of the EGO delay table." ego_delay_loads = "Load (y) axis of the EGO delay table." ego_sensor_delay = "Static value representing O2 sensor response time" generic_pid_flags_a_on = "Generic Closed-Loop channel A on or off.\nA table is used to plot the desired value of the feedback value (PV) based on a lookup from the input variables.\nA closed-loop PID method adjusts the PWM output until the desired feedback value is achieved." generic_pid_flags_a_type = "Type B (change in error affects P term) or\nType C (change in PV affects P term) PID" generic_pid_flags_a_direction = "Output polarity for PID output" generic_pid_flags_a_output_type = "Use a PWM output or the stepper output for PID output" generic_pid_flags_a_lookup_type = "Use a table or a curve for closed-loop table lookup" generic_pid_flags_b_on = "Generic Closed-Loop channel B on or off.\nA table is used to plot the desired value of the feedback value (PV) based on a lookup from the input variables.\nA closed-loop PID method adjusts the PWM output until the desired feedback value is achieved." generic_pid_flags_b_type = "Type B (change in error affects P term) or\nType C (change in PV affects P term) PID" generic_pid_flags_b_direction = "Output polarity for output" generic_pid_flags_b_output_type = "Use a PWM output or the stepper output for PID output" generic_pid_flags_b_lookup_type = "Use a table or a curve for closed-loop table lookup" generic_pid_pwm_opts_freq_a = "Frequency to use for PWM output" generic_pid_pwm_opts_freq_b = "Frequency to use for PWM output" generic_pid_pwm_outs_a = "Output pin.\nThis is the output to control the actuator (or whatever) that change the process.\ne.g. opens or closes a valve." generic_pid_pwm_outs_b = "Output pin.\nThis is the output to control the actuator (or whatever) that change the process.\ne.g. opens or closes a valve." generic_pid_upper_inputlim_a = "Maximum value for feedback input (PV)" generic_pid_upper_inputlim_b = "Maximum value for feedback input (PV)" generic_pid_lower_inputlim_a = "Minimum value for feedback input (PV)" generic_pid_lower_inputlim_b = "Minimum value for feedback input (PV)" generic_pid_output_upperlim_a = "Maximum output duty" generic_pid_output_upperlim_b = "Maximum output duty" generic_pid_output_lowerlim_a = "Minimum output duty" generic_pid_output_lowerlim_b = "Minimum output duty" generic_pid_rpms_a = "RPM axis bins for lookup table" generic_pid_rpms_b = "RPM axis bins for lookup table" generic_pid_loadvals_a = "Load axis bins for lookup table" generic_pid_loadvals_b = "Load axis bins for lookup table" generic_pid_targets_a = "Generic PID lookup table\n\nThis is the target value which the closed-loop algorithm aims to match to the feedback input by controlling the PWM output." generic_pid_targets_b = "Generic PID lookup table\n\nThis is the target value which the closed-loop algorithm aims to match to the feedback input by controlling the PWM output." generic_pid_control_interval_a = "Time in milliseconds between each run of PID control loop" generic_pid_control_interval_b = "Time in milliseconds between each run of PID control loop" generic_pid_P_a = "Proportional gain" generic_pid_P_b = "Proportional gain" generic_pid_I_a = "Integral gain" generic_pid_I_b = "Integral gain" generic_pid_D_a = "Derivative gain" generic_pid_D_b = "Derivative gain" generic_pid_load_offset_a = "Variable used as the Y load axis in the lookup table" generic_pid_PV_offset_a = "Variable used as feedback input (PV)" generic_pid_load_offset_b = "Variable used as the Y load axis in the lookup table" generic_pid_PV_offset_b = "Variable used as feedback input (PV)" outmsg1_offset01 = "Offset in the OutputChannels of the first variable in the outmsg 1. The outmsg is used to transfer a set of variables to a CAN device. The CAN device must support this and initiate the transfer. The list of variables must match on both devices." outmsg1_size01 = "Size in bytes of the first variable in the outmsg 1" outmsg2_offset01 = "Offset in the OutputChannels of the first variable in the outmsg 2. The outmsg is used to transfer a set of variables to a CAN device. The CAN device must support this and initiate the transfer. The list of variables must match on both devices." outmsg2_size01 = "Size in bytes of the first variable in the outmsg 2" outmsg3_offset01 = "Offset in the OutputChannels of the first variable in the outmsg 3. The outmsg is used to transfer a set of variables to a CAN device. The CAN device must support this and initiate the transfer. The list of variables must match on both devices." outmsg3_size01 = "Size in bytes of the first variable in the outmsg 3" outmsg4_offset01 = "Offset in the OutputChannels of the first variable in the outmsg 4. The outmsg is used to transfer a set of variables to a CAN device. The CAN device must support this and initiate the transfer. The list of variables must match on both devices." outmsg4_size01 = "Size in bytes of the first variable in the outmsg 4" dwell_table_values = "Specifies the base dwell time in milliseconds based on RPM/load.\nThis can be used to reduce dwell where possible to increase spark-plug life.\nAreas in the tune of very rich or very dilute mixture will need most spark energy.\n(Battery voltage correction is applied afterwards.)" spkadj_max = "Sets a limit on the maximum adjustment a remote device (e.g. trans controller) can apply to the ignition timing.\nThis is a positive number, meaning advance." spkadj_min = "Sets a limit on the minimum adjustment a remote device (e.g. trans controller) can apply to the ignition timing.\nThis is a negative number, meaning retard." cranktaper_pct = "Allows cranking fuel to be tapered down during extended cranking to reduce flooding.\n100% means normal cranking pulsewidth." flashlock = "Locks or unlocks the sensor calibration tables.\nLocked = Prevents accidental changes to the tables.\nUnlocked = Allows fresh calibrations to be written.\n\nEnsure you lock again after writing the calibration tables." scatterRuntimeEnabled = "On = Enables a faster method of collecting realtime data from MS3. Off = use previous slower method for realtime data." pwm_opt_load_a_offset = "This selects the 'load' axis on the table or curve." pwm_opt_load_b_offset = "This selects the 'load' axis on the table or curve." pwm_opt_load_c_offset = "This selects the 'load' axis on the table or curve." pwm_opt_load_d_offset = "This selects the 'load' axis on the table or curve." pwm_opt_load_e_offset = "This selects the 'load' axis on the table or curve." pwm_opt_load_f_offset = "This selects the 'load' axis on the table or curve." ; tool tips end tooltips [Menu] ;---------------------------------------------------------------------------- ; There are five pre-defined values that may be used to define your menus. ; The first four allow access to the "standard" dialog boxes, the last one ; merely draws a separator (horizontal line) in the menu. ; ; std_constants ; std_enrichments ; std_realtime ; std_warmup ; std_accel ; ; std_separator ; ; Additionally, to support MegaSquirt-II firmware, there are two standard ; dialogs to generate its three embedded tables. The first of these acts ; like Roger Enns' EasyTherm, but only works for MS-II. The second one ; generates the internal AFR table required for proper closed loop operation ; in MS-II. Use these without page numbers, as they will just be ignored ; in any case. ; ; std_ms2gentherm ; std_ms2geno2 ; ; If you use any of the std_constants, std_enrichments or std_warmup ; editors, they may be optionally suffixed with a page number (only ; useful for multi-page code variants), which causes them to edit the ; specified page. If you leave off the page specifier, they edit logical ; page one as specified in the Constants section. ; ; There are four special menu names, which when used append to the standard ; menus of the same name instead of creating a new one. The menu names ; are "File", "Communications", "Tools" and "Help". ; ;---------------------------------------------------------------------------- menuDialog = main menu = "Basic/Load Settings" subMenu = base, "Engine and Sequential Settings" subMenu = generalsettings2, "General Settings" subMenu = revlimiter2, "Rev Limiter" subMenu = shiftlight, "Shift Light" subMenu = std_separator subMenu = tacho, "Tacho Output" subMenu = fan_control, "Fan Control" subMenu = tcluparams, "Torque Convertor Lockup" subMenu = alternator, "Alternator Control" subMenu = std_separator subMenu = barometerCorr, "Barometric Correction",0, {baroCorr} subMenu = map_sample_dialog, "MAP Sample Settings" subMenu = std_separator subMenu = ITBcombined, "ITB Load Settings", 0, { algorithm == 6 || algorithm2 == 6 || IgnAlgorithm == 6 || IgnAlgorithm2 == 6 || afrload == 6 || eaeload == 6 } subMenu = mafdialog, "MAF Settings" subMenu = MAFtable, "MAF Flow Curve", 0, {!feature7_mafcalib} subMenu = MAFtable1old, "MAF Correction Table (Old)", 0, {feature7_mafcalib} subMenu = manifoldTempCorr,"MAF/MAT Correction Table", 0, {feature7_mafmat && ((algorithm == 5) || (algorithm2 == 4) || (algorithm2 == 5))} subMenu = std_separator subMenu = manifoldTempCorr2,"MAT Air Density Table", 0, {((algorithm != 4) && (algorithm != 5) && (algorithm2 != 4) && (algorithm2 != 5))} subMenu = matclt_curve, "MAT/CLT Correction", 0, {(algorithm != 4) && (algorithm != 5) && (algorithm2 != 4) && (algorithm2 != 5)} subMenu = std_separator subMenu = std_realtime, "&Realtime Display" subMenu = iopinlist, "Feature List Showing I/O pins" subMenu = pinusage, "I/O pins List Showing Usage" subMenu = pinusagecan, "Expansion I/O pins List/Usage" subMenu = limitsettings, "Gauge and Settings Limits" menu = "F&uel Settings" subMenu = injsettings, "Injector Dead-Time/PWM" #if CYL_12_16_SUPPORT subMenu = injsettingsb, "Injector Dead-Time/PWM (9-16)" #endif subMenu = smallpw, "Injector Small Pulsewidths" #if CYL_12_16_SUPPORT subMenu = smallpwb, "Injector Small Pulsewidths (9-16)" #endif subMenu = inj_timing_tbl, "Injector Timing Table", 0, { sequential != 0 } subMenu = inj_timing_sec_tbl, "Secondary Injector Timing Table", 0, { sequential != 0 && (dualfuel_sw_on || staged_first_param) } subMenu = stagedCombined, "Staged Injection" subMenu = flexFuelSettings,"Fuel Sensor Settings (Flex)" subMenu = overrun, "Over-Run Fuel Cut" subMenu = std_separator subMenu = egoControl, "AFR/&EGO Control" #if CYL_12_16_SUPPORT subMenu = egocont9_16, "AFR/EGO (9-16)" #endif subMenu = afrTable1Tbl, "A&FR Table 1", 0 subMenu = afrTable2Tbl, "AF&R Table 2", 0, { (!dualfuel_sw_on && tsw_pin_afr) || (dualfuel_sw_on && dualfuel_sw_afr) || ( N2Oopt_2 && N2Oopt_4) } subMenu = ego_auth_Tbl, "EGO Authority Table", 0, {egoType && egoAlgorithm_auth } subMenu = ego_delay_Tbl, "EGO Delay Table", 0, {egoType && (egoAlgorithm < 3) && egoAlgorithm_delay_table} subMenu = narrowband_tgts_tbl, "Narrowband EGO targets", 0, { egoType == 1 } subMenu = maxafr, "AFR safety system" subMenu = std_separator subMenu = veTable1Tbl, "Fuel VE Table &1", 0, { ((algorithm != 5) || ((algorithm == 5) && (feature7_maftrim))) } subMenu = veTable2Tbl, "Fuel VE Table &2", 0, { (algorithm2 != 0) } subMenu = veTable3Tbl, "Fuel VE Table 3", 0, { ((algorithm != 5) || ((algorithm == 5) && (feature7_maftrim))) && ((!dualfuel_sw_on && f5_0_tsf) || (dualfuel_sw_on && dualfuel_sw_fuel) || (dualfuel_sw_on && dualfuel_opt_mode)) } subMenu = veTable4Tbl, "Fuel VE Table 4", 0, { (algorithm2 != 0) && ((!dualfuel_sw_on && f5_0_tsf) || (dualfuel_sw_on && dualfuel_sw_fuel) || (dualfuel_sw_on && dualfuel_opt_mode)) } subMenu = std_separator subMenu = inj_trim1Tbl, "Injector 1 Trim", 7, { (hardware_fuel==0) && sequential_trim_on_off } subMenu = inj_trim2Tbl, "Injector 2 Trim", 7, { (hardware_fuel==0) && sequential_trim_on_off } subMenu = inj_trimad, "Cyl 1-4 Trims", 7, { hardware_fuel && sequential_trim_on_off } subMenu = inj_trimeh, "Cyl 5-8 Trims", 7, { hardware_fuel && (nInjectors > 4) && sequential_trim_on_off } #if CYL_12_16_SUPPORT subMenu = inj_trimil, "Cyl 9-12 Trims", 7, { hardware_fuel && (nInjectors > 8) && sequential_trim_on_off } subMenu = inj_trimmp, "Cyl 13-16 Trims", 7, { hardware_fuel && (nInjectors > 12) && sequential_trim_on_off } #endif subMenu = std_separator subMenu = injseq, "Sequenced Batch Fire", 0, { sequential == 0 } subMenu = std_separator subMenu = fuelpump, "Fuel Pump and Pressure" subMenu = fp_temp_curve, "Temperature Adjustment", 0, {fueltemp1 && fueltemp1_corr} subMenu = fp_press_curve, "Pressure Adjustment", 0, {(fp_opt_mode != 2) && fp_press_in && (fp_opt_reg == 2)} subMenu = fp_safety, "Fuel Pressure Safety", 0, {fp_press_in} subMenu = std_separator subMenu = fuelcalcs, "Fuel Calculations Summary" menu = "&Ignition Settings" subMenu = combinedignition, "Ignition Options/Wheel Decoder" subMenu = std_trigwiz, "Tri&gger Wizard", 0,{ (spk_mode0 != 31) && (spk_mode0 != 4) } subMenu = std_separator subMenu = dwellSettings, "D&well Battery Correction", 0, { spk_mode0 != 31 } subMenu = dwellrpm_curve, "Dwell vs RPM", 0, {spk_mode0 > 1 && dwellmode == 2 && spk_conf2_dwell} subMenu = dwell_tbl, "Dwell Table", 0, {(spk_mode0 > 1) && (dwellmode == 0) && spk_conf2_dwelltbl} subMenu = std_separator subMenu = coldAdvance, "&Cold Advance", 0, { spk_mode0 != 31 } subMenu = matBasedRetard, "MAT-&Based Timing Retard", 0, { spk_mode0 != 31 } subMenu = noisefiltering2, "Noise Filtering", 0 subMenu = std_separator subMenu = knockSettings, "&Knock Sensor Settings" subMenu = knockSettings4, "Knock Sensor Parameters", 0, {knk_option && (knk_option_an == 3)} subMenu = knockSettings2, "Knock Window Settings", 0, {knk_option} subMenu = knockupscale_curve, "Knock Coolant Scaling", 0, {knk_option} subMenu = std_separator subMenu = ignitionTbl1, "&Ignition Table 1", 0, { (spk_mode0 != 31) } subMenu = ignitionTbl2, "Ignition Table 2", 0, { (IgnAlgorithm2 !=0) && (spk_mode0 != 31)} subMenu = ignitionTbl3, "Ignition Table 3", 0, { (!dualfuel_sw_on && f5_0_tss) || (dualfuel_sw_on && dualfuel_sw_spk) } subMenu = ignitionTbl4, "Ignition Table 4", 0, { (IgnAlgorithm2 !=0) && ((!dualfuel_sw_on && f5_0_tss) || (dualfuel_sw_on && dualfuel_sw_spk)) } subMenu = std_separator subMenu = RotaryTrailingSettings, "Rotary Settings", 0, { (twoStroke == 3) && (spk_mode0 != 31) } subMenu = RotarySplitTbl, "Rotary Split Table", 0, { (twoStroke == 3) && (spk_mode0 != 31) } subMenu = std_separator subMenu = spk_trimad, "Cyl 1-4 Trims", 8, { spk_mode3_trim } subMenu = spk_trimeh, "Cyl 5-8 Trims", 8, { spk_mode3_trim && (nCylinders > 4)} #if CYL_12_16_SUPPORT subMenu = spk_trimil, "Cyl 9-12 Trims", 8, { spk_mode3_trim && (nCylinders > 8)} subMenu = spk_trimmp, "Cyl 13-16 Trims", 8, { spk_mode3_trim && (nCylinders > 12)} #endif subMenu = std_separator subMenu = sparkcalcs, "Spark Calculations Summary" menu = "&Startup/Idle" subMenu = crsettings, "Cranking/Startup Settings", 0 subMenu = primingPW, "Pri&ming Pulse", 0 subMenu = crankingPW, "Cra&nking Pulse", 0 subMenu = cranktaper_curvet, "Cranking Taper Curve", 0, {feature7_cranktaper}, {feature7_crtpunits == 0} subMenu = cranktaper_curvee, "Cranking Taper Curve", 0, {feature7_cranktaper}, {feature7_crtpunits == 1} subMenu = nestedasePct, "AfterStart Enrichment (ASE)", 0 subMenu = aseTaper, "AfterStart Enrichment (ASE) Taper", 0 subMenu = nestedwarmup_curve, "&Warmup Enrichment (WUE)", 0 subMenu = std_separator subMenu = primingPW2, "Priming Pulse 2", 0, { (dualfuel_sw_on && dualfuel_sw2_prime) } subMenu = crankingPW2, "Cranking Pulse 2", 0, { (dualfuel_sw_on && dualfuel_sw2_crank) || alternate_blend } subMenu = nestedasePct2, "AfterStart Enrichment (ASE) 2", 0, { (dualfuel_sw_on && dualfuel_sw_ase) } subMenu = aseTaper2, "AfterStart Enrichment (ASE) Taper 2", 0, { (dualfuel_sw_on && dualfuel_sw_ase) } subMenu = nestedwarmup_curve2, "Warmup Enrichment (WUE) 2", 0, { (dualfuel_sw_on && dualfuel_sw_wue) } subMenu = std_separator subMenu = combinedidle, "I&dle Control" subMenu = pwmidle_crank_dutyorsteps_curve, "Idle Cranking Duty/Steps", 0, {IdleCtl > 1} subMenu = idlebins, "Idle Warmup Duty/Steps", 0, {(IdleCtl > 1) && (IdleCtl_alg == 0)} subMenu = combinedCLidle, "Closed-Loop Idle Settings", 0, {IdleCtl && (IdleCtl_alg == 1)} subMenu = pwmidle_target_curve, "Closed-Loop Idle Target Curve", 0, { ((IdleCtl > 1) && (IdleCtl_alg == 1)) || idle_special_ops_timing_assist } subMenu = pwmidle_cl_initialvalues, "Closed-Loop Idle Initial Values", 0, { pwmidle_cl_opts_initvaluetable && (IdleCtl > 1) && (IdleCtl_alg == 1) } subMenu = idle_voltage_comp_curve, "PWM Idle Voltage Compensation", 0, {IdleCtl == 2} subMenu = ac_idleup, "Air Conditioning Idle-up", 0 subMenu = std_separator subMenu = idleAdvance, "Idle Advance Settings" subMenu = cl_idle_timing_curve, "Idle RPM Timing Correction Curve", 0, { idle_special_ops_timing_assist } subMenu = idleVe, "Idle VE Settings" menu = "Accel Enrich" subMenu = accelsettings, "Accel Enrich Settings" subMenu = AEtime_settings, "Time-Based Accel",0, { !(AE_options & 0x1) } subMenu = AEpump_settings, "Accel-Pump Accel Enrichment Settings",0, { AE_options & 0x1 } subMenu = tpswot_curve, "TPS WOT Curve", 0, {feature7_aetpswot} subMenu = std_separator subMenu = EAEBAWCcurve, "EAE Adhere-to-walls Coefficient", 0, { EAEOption == 1 || EAEOption == 2 } subMenu = EAEBSOCcurve, "EAE Sucked-from-walls Coefficient", 0, { EAEOption == 1 || EAEOption == 2 } subMenu = EAEAWNcurve, "EAE Adhere-to-walls RPM Correction", 0, { EAEOption == 1 || EAEOption == 2 } subMenu = EAEcombi1, "EAE Sucked/Adhered Coefficients", 0, { EAEOption == 1 || EAEOption == 2 } subMenu = EAESONcurve, "EAE Sucked-from-walls RPM Correction", 0, { EAEOption == 1 || EAEOption == 2 } subMenu = EAEAWWcurve, "EAE Adhere-to-walls CLT Correction", 0, { EAEOption == 1 || EAEOption == 2 } subMenu = EAESOWcurve, "EAE Sucked-from-walls CLT Correction", 0, { EAEOption == 1 || EAEOption == 2 } subMenu = EAElagcomp, "EAE Lag Compensation", 0, {EAEOption == 2} subMenu = std_separator subMenu = EAEBAWCcurve2, "EAE Adhere-to-walls Coefficient 2", 0, { (EAEOption == 1 || EAEOption == 2) && (staged_first_param ) } subMenu = EAEBSOCcurve2, "EAE Sucked-from-walls Coefficient 2", 0, { (EAEOption == 1 || EAEOption == 2) && (staged_first_param ) } subMenu = EAEAWNcurve2, "EAE Adhere-to-walls RPM Correction 2", 0, { (EAEOption == 1 || EAEOption == 2) && (staged_first_param ) } subMenu = EAESONcurve2, "EAE Sucked-from-walls RPM Correction 2", 0, { (EAEOption == 1 || EAEOption == 2) && (staged_first_param ) } subMenu = EAEAWWcurve2, "EAE Adhere-to-walls CLT Correction 2", 0, { (EAEOption == 1 || EAEOption == 2) && (staged_first_param ) } subMenu = EAESOWcurve2, "EAE Sucked-from-walls CLT Correction 2", 0, { (EAEOption == 1 || EAEOption == 2) && (staged_first_param ) } subMenu = std_separator subMenu = XAccTable, "Puddling Factors (Accel)", 0, { EAEOption == 3 || EAEOption == 4 } subMenu = XDecTable, "Puddling Factors (Decel)", 0, { EAEOption == 3 || EAEOption == 4 } subMenu = TauAccTable, "Time Factors (Accel)", 0, { EAEOption == 3 || EAEOption == 4 } subMenu = TauDecTable, "Time Factors (Decel)", 0, { EAEOption == 3 || EAEOption == 4 } subMenu = XCltTable, "&X (Puddling) Temp. Corrections",0, { EAEOption == 4 } subMenu = TCltTable, "&Tau (Time) Temp. Corrections", 0, { EAEOption == 4 } menu = "Boost/VVT" subMenu = boost, "Boost Control Settings" subMenu = boostctlDutys, "Boost Control Duty Table", 0, { (boost_ctl_settings_on) && (!boost_ctl_settings_cl)} subMenu = boostctlTargs, "Boost Control Target Table", 0, { (boost_ctl_settings_on == 1) && (boost_ctl_settings_cl == 1) } subMenu = boostctlCLPWMtargs1, "Boost Control Initial Duty Table 1", 0, { (boost_ctl_settings_on == 1) && (boost_ctl_settings_cl == 1) && (boost_ctl_settings_initialvals == 1) } subMenu = boost_timed_curve, "Boost Delay (Timed From Launch)",0, { boost_ctl_settings_on && launch_opt_on && boost_feats_timed } subMenu = boostvss_curve, "Boost Control vs Speed", 0, { (boost_ctl_settings_on) && ((boost_vss == 1) || (boost_vss == 2))} subMenu = std_separator subMenu = boostctlSettings2, "Boost Control Settings 2", 0 , {boost_ctl_settings_on} subMenu = boostctlDutys2, "Boost Control Duty Table 2", 0, { boost_ctl_settings_on && (((!boost_ctl_settings_cl) && (boost_feats_tsw || dualfuel_sw2_boosw)) || (boost_ctl_settings_on2 && !boost_ctl_settings_cl2)) } subMenu = boostctlTargs2, "Boost Control Target Table 2", 0, { boost_ctl_settings_on && ((boost_ctl_settings_cl && (boost_feats_tsw || dualfuel_sw2_boosw)) || (boost_ctl_settings_on2 && boost_ctl_settings_cl2)) } subMenu = boostctlCLPWMtargs2, "Boost Control Initial Duty Table 2", 0, { boost_ctl_settings_on && ((boost_ctl_settings_cl && boost_ctl_settings_initialvals && (boost_feats_tsw || dualfuel_sw2_boosw)) || (boost_ctl_settings_on2 && boost_ctl_settings_cl2)) } subMenu = std_separator subMenu = antilag, "Turbo Anti-lag (ALS)" subMenu = antilagtables, "Turbo Anti-lag Tables", 0, {als_in_pin} subMenu = als_rifuelcut_tbl, "Turbo Anti-lag Roving Idle", 0, {als_in_pin && als_opt_ri && hardware_fuel && sequential} subMenu = std_separator subMenu = vvtparams, "VVT Settings" subMenu = vvt_timing1_tbl, "VVT Intake Table", 0, {vvt_opt1_on && vvt_opt2_pid2} subMenu = vvt_timing2_tbl, "VVT Exhaust Table", 0, {vvt_opt1_on && vvt_opt2_pid2 && (vvt_opt5_vvt1 || vvt_opt5_vvt2 || vvt_opt1_on > 2)} subMenu = pwm_duties_Tbl_vvt, "VVT On/Off Table", 0, {vvt_opt1_on && !vvt_opt2_pid2} menu = "Table choices" subMenu = tablesw, "Table Switch/Dual Fuel" subMenu = dualfuel_temp_curve, "Temperature Adjustment", 0, { (dualfuel_sw_on && dualfuel_opt_temp) } subMenu = dualfuel_press_curve, "Pressure Adjustment", 0, { (dualfuel_sw_on && dualfuel_opt_press) } subMenu = injsettings2, "Alt. Injector Dead-time/PWM 2", 0, { (dualfuel_sw_on && dualfuel_sw2_injp) } #if CYL_12_16_SUPPORT subMenu = injsettingsb2, "Alt. Injector Dead-time/PWM 2 (9-16)", 0, { (dualfuel_sw_on && dualfuel_sw2_injp) } #endif subMenu = smallpw2, "Alt. Injector Small Pulsewidths 2", 0, { (dualfuel_sw_on && dualfuel_sw2_smpw) } #if CYL_12_16_SUPPORT subMenu = smallpw2b, "Alt. Injector Small Pulsewidths 2 (9-16)", 0, { (dualfuel_sw_on && dualfuel_sw2_smpw) } #endif subMenu = std_separator subMenu = blend1menu, "Blend Curve (1) VE1->2", 0, {algorithm2 && (loadCombine == 2)} subMenu = blend2menu, "Blend Curve (2) Spk1->2", 0, {IgnAlgorithm2 && (loadCombineign == 1)} subMenu = blend3menu, "Blend Curve (3) VE1+2->3+4", 0, {f5_0_tsf && (f5_0_tsf_opt == 0) && (tsw_pin_f == 14)} subMenu = blend4menu, "Blend Curve (4) Spk1+2->3+4", 0, {f5_0_tss && (f5_0_tss_opt == 0) && (tsw_pin_s == 14)} subMenu = blend5menu, "Blend Curve (5) AFR1->2", 0, {tsw_pin_afr == 14} subMenu = blend6menu, "Blend Curve (6) Boost1->2", 0, {(boost_feats_tsw == 14) && boost_ctl_settings_on} subMenu = blend7menu, "Blend Curve (7) Crank%1->2", 0, {alternate_blend} menu = "Advanced Engine" subMenu = speedsensors, "Speed and Gear Sensors" subMenu = ss, "Shaft Speed Sensors" subMenu = egt, "EGT/Thermocouple Settings" subMenu = sensors, "Generic Sensor Inputs" subMenu = accelerometer, "Accelerometer Parameters" subMenu = tcsettings, "Traction Control Settings" subMenu = tc_perfect_curve, "Traction Control - Perfect Run VSS", 0, {tc_opt_on && (tc_opt_method == 0)} subMenu = tc_perfectrpm_curve, "Traction Control - Perfect Run RPM", 0, {tc_opt_on && (tc_opt_method == 2)} subMenu = tcslip_menu, "Traction Control - External Slip% Input", 0, {tc_opt_on && (tc_opt_method == 1) && tc_opt_slipcurve} subMenu = tc_curves, "Traction Control Reactions", 0, {tc_opt_on} subMenu = std_separator subMenu = launch, "Launch / 2-step / 3-step / T-brake" subMenu = launch_retard_time, "Timed Retard After Launch", 0, {launch_opt_on && launch_opt_retard} subMenu = vsslaunch, "Speed-based Launch Control" subMenu = ShiftSettings, "Sequential Shift Cut" subMenu = nitrous, "&Nitrous System" subMenu = nitrous_curves_time, "Nitrous - Time-Based Progressive",0, {N2Oopt_2 && N2Oopt2_prog && N2Oopt2_prog_time} subMenu = nitrous_curves_rpm, "Nitrous - RPM-Based Progressive", 0, {N2Oopt_2 && N2Oopt2_prog && !N2Oopt2_prog_time} subMenu = waterinj, "Water Injection" subMenu = hpte, "High Power Time Enrichment" subMenu = oilpress, "Oil Pressure" subMenu = std_separator subMenu = ms3_port_edit_wrap, "Programmable On/Off Outputs" subMenu = gen_pwm_a, "Generic PWM output A" subMenu = gen_pwm_b, "Generic PWM output B" subMenu = gen_pwm_c, "Generic PWM output C" subMenu = gen_pwm_d, "Generic PWM output D" subMenu = gen_pwm_e, "Generic PWM output E", 0, {!(vvt_opt1_on)} subMenu = gen_pwm_f, "Generic PWM output F" subMenu = std_separator subMenu = generic_pid_a, "Generic Closed-Loop A" subMenu = generic_pid_b, "Generic Closed-Loop B" ; subMenu = userdefined, "User defined menu" ; uncomment this line to enable menuDialog = main menu = "3D &Tuning Maps" subMenu = veTable1Map, "Fuel VE Table &1",0, { ((algorithm != 5) || ((algorithm == 5) && (feature7_maftrim))) } subMenu = veTable2Map, "Fuel VE Table &2", 0, { (algorithm2 != 0) && (algorithm2 != 5) } subMenu = veTable3Map, "Fuel VE Table &3", 0, { (!dualfuel_sw_on && f5_0_tsf) || (dualfuel_sw_on && dualfuel_sw_fuel) || (dualfuel_sw_on && dualfuel_opt_mode) } subMenu = veTable4Map, "Fuel VE Table &4", 0, { ((!dualfuel_sw_on && f5_0_tsf) || (dualfuel_sw_on && dualfuel_sw_fuel) || (dualfuel_sw_on && dualfuel_opt_mode)) && (algorithm2 != 0) } subMenu = afrTable1Map, "A&FR Table 1", 0, { egoType > 1 } subMenu = afrTable2Map, "AF&R Table 2", 0, { (egoType > 1) && ((!dualfuel_sw_on && tsw_pin_afr) || (dualfuel_sw_on && dualfuel_sw_afr)) } subMenu = std_separator ;---------------------------------------------- subMenu = ignitionMap1, "&Ignition Table 1", 0, {(spk_mode0 != 31)} subMenu = ignitionMap2, "Ignition Table 2", 0, { (IgnAlgorithm2 != 0) && (spk_mode0 != 31)} subMenu = ignitionMap3, "Ignition Table 3", 0, { (!dualfuel_sw_on && f5_0_tss) || (dualfuel_sw_on && dualfuel_sw_fuel) } subMenu = ignitionMap4, "Ignition Table 4", 0, { (IgnAlgorithm2 !=0) && ((!dualfuel_sw_on && f5_0_tss) || (dualfuel_sw_on && dualfuel_sw_spk)) } subMenu = RotarySplitMap, "Rotary Split Table", 0, {(twoStroke == 3) && (spk_mode0 != 31)} subMenu = std_separator ;---------------------------------------------- subMenu = boostctlDtyMap, "Boost Control Duty Table", 0, {boost_ctl_settings_on && boost_ctl_settings_cl == 0} subMenu = boostctlTargMap, "Boost Control Target Table", 0, {boost_ctl_settings_on && boost_ctl_settings_cl} subMenu = boostctlDtyMap2, "Boost Control Duty Table 2", 0, {boost_ctl_settings_on && boost_ctl_settings_cl == 0} subMenu = boostctlTargMap2, "Boost Control Target Table 2", 0, {boost_ctl_settings_on && boost_ctl_settings_cl} subMenu = std_separator subMenu = inj_timing_map, "Sequential Injector Timing Table", 0, { sequential != 0 } subMenu = inj_timing_sec_map, "Sequential Injector Secondary Timing Table", 0, { sequential != 0 && (dualfuel_sw_on || staged_first_param) } menu = "CAN-bus/ Testmodes" subMenu = canparams, "CAN Parameters" subMenu = canbroadcast, "CAN Broadcasting",0, {can_enable_on} subMenu = canvss, "CAN VSS, Gear, EGO, GPS",0, {can_enable_on} subMenu = realtimeclock, "Real Time Clock" subMenu = std_separator ;---------------------------------------------- subMenu = checkengine, "Check Engine Light" subMenu = limpmode, "Limp Mode", 0, {cel_opt_on} subMenu = alphaMAPTbl, "Fallback MAP Table", 0, {cel_opt_on && cel_opt2_map && cel_action1_map && cel_action1_map_an} subMenu = std_separator ;---------------------------------------------- subMenu = outputtest, "Output Test Mode - Inj/Spk" subMenu = outputtest_io, "Output Test Mode - I/O" subMenu = iactest, "Output Test Mode - Idle Valve ", 0, {IdleCtl} subMenu = injseqtest, "Injector Sequential Testing" subMenu = injspkonoff, "Inj/Spk Disabling Test Mode" subMenu = std_separator ;---------------------------------------------- subMenu = special, "Special Options" subMenu = std_separator subMenu = lttrim, "Long Term Trim Settings" subMenu = ltt_Table1Tbl, "Long Term Trim Table &1", 0 #if OUTMSG_EDITING subMenu = std_separator subMenu = outmsg1, "Outmsg 1" subMenu = outmsg2, "Outmsg 2" subMenu = outmsg3, "Outmsg 3" subMenu = outmsg4, "Outmsg 4" #endif menuDialog = main menu = "T&ools" subMenu = sensorCal, "Calibrate MAP/Baro" subMenu = battcalib, "Calibrate Battery Voltage" subMenu = std_separator ;---------------------------------------------- subMenu = flash_unlock, "Un/Lock Calibrations" subMenu = std_ms2gentherm, "Calibrate T&hermistor Tables", 0, {flashlock} subMenu = std_ms2geno2, "Calibrate &AFR Table", 0, {flashlock} subMenu = mafTableBurner, "Calibrate &MAF Table", 0, {flashlock && feature7_mafcalib} menu = "Data Logging" subMenu = sdcard_datalog, "SD Card Datalogging" subMenu = std_ms3SdConsole, "Browse / Import SD Card",0, {log_style_on2 && (tsLocalCanId == tsCanId) } menu = "Communications" subMenu = setbaud, "Megasquirt Baud Rate", 0 menu = "Help" subMenu = helpGeneral, "Megasquirt 3 Info" ;------------------------------------------------------------------------------- [VerbiageOverride] ; text over-rides for internal TS dialogs. "Engine Stroke" = "Engine Stroke/Rotary" "Number of Cylinders" = "No. Cylinders/Rotors" [ControllerCommands] ; commandName = command1, command2, commandn... ; command in standard ini format, a command name can be assigned to 1 to n commands that will be executed in order. ; This does not include any resultant protocol envelope data, only the response data itself. ; WARNING!! These commands bypass TunerStudio's normal memory synchronization. If these commands ; alter mapped settings (Constant) memory in the controller, TunerStudio will have an out of sync condition ; and may create error messages. ; It is expected that these commands would not typically alter any ram mapped to a Constant. cmdStopTestmode = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x00" cmdEnterTestMode = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x01" cmdtestspkon = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x02" cmdtestinjon = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x03" cmdfpon = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x05" cmdfpoff = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x06" cmdtestinjspkoff = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x07" cmdtestiacoff = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x08" cmdtestiachome = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x09" cmdtestiacon = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x0a" cmdskipinjoff= "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x0b" cmdskipinjon = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x0c" cmdskipspkon = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x0d" cmdtestinjnorm = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x10" cmdtestinjbat = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x11" cmdtestinjsem = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x12" cmdtestinjseq = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x13" cmdtestiaccycle = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x18" cmdtest10off = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x80" cmdtest10pulsed = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x82" cmdtest10on = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x83" cmdtest11off = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x84" cmdtest11pulsed = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x86" cmdtest11on = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x87" cmdtest12off = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x88" cmdtest12pulsed = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x8a" cmdtest12on = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x8b" cmdtest13off = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x8c" cmdtest13pulsed = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x8e" cmdtest13on = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x8f" cmdtest14off = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x90" cmdtest14pulsed = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x92" cmdtest14on = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x93" cmdtest15off = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x94" cmdtest15pulsed = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x96" cmdtest15on = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x97" cmdtest16off = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x98" cmdtest16pulsed = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x9a" cmdtest16on = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x9b" cmdbaudlow = "w\$tsCanId\x07\x02\x99\x00\x01\x50" cmdbaudhigh = "w\$tsCanId\x07\x02\x99\x00\x01\x51" cmdlttr1 = "w\$tsCanId\x07\x02\x9a\x00\x01\x41" cmdlttr2 = "w\$tsCanId\x07\x02\x9a\x00\x01\x42" cmdlttw = "w\$tsCanId\x07\x02\x9a\x00\x01\x51" cmdlttz = "w\$tsCanId\x07\x02\x9a\x00\x01\x61" cmdinjspk1 = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x20" cmdinjspk2 = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x21" cmdinjspk3 = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x22" cmdinjspk4 = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x23" cmdinjspk5 = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x24" cmdinjspk6 = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x25" cmdinjspk7 = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x26" cmdinjspk8 = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x27" cmdinjspk9 = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x28" cmdinjspk10 = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x29" cmdinjspk11 = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x2a" cmdinjspk12 = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x2b" cmdinjspk13 = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x2c" cmdinjspk14 = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x2d" cmdinjspk15 = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x2e" cmdinjspk16 = "w\$tsCanId\x07\x02\x87\x00\x03\x30\x39\x2f" [UserDefined] dialog = outmsg1_off, "", yAxis field = "Variable Offset" field = "01", outmsg1_offset01 field = "02", outmsg1_offset02 field = "03", outmsg1_offset03 field = "04", outmsg1_offset04 field = "05", outmsg1_offset05 field = "06", outmsg1_offset06 field = "07", outmsg1_offset07 field = "08", outmsg1_offset08 field = "09", outmsg1_offset09 field = "10", outmsg1_offset10 field = "11", outmsg1_offset11 field = "12", outmsg1_offset12 field = "13", outmsg1_offset13 field = "14", outmsg1_offset14 field = "15", outmsg1_offset15 field = "16", outmsg1_offset16 dialog = outmsg1_size, "", yAxis field = " Size" field = "", outmsg1_size01 field = "", outmsg1_size02 field = "", outmsg1_size03 field = "", outmsg1_size04 field = "", outmsg1_size05 field = "", outmsg1_size06 field = "", outmsg1_size07 field = "", outmsg1_size08 field = "", outmsg1_size09 field = "", outmsg1_size10 field = "", outmsg1_size11 field = "", outmsg1_size12 field = "", outmsg1_size13 field = "", outmsg1_size14 field = "", outmsg1_size15 field = "", outmsg1_size16 dialog = outmsg1, "Outmsg 1", xAxis panel = outmsg1_off panel = outmsg1_size dialog = outmsg2_off, "", yAxis field = "Variable Offset" field = "01", outmsg2_offset01 field = "02", outmsg2_offset02 field = "03", outmsg2_offset03 field = "04", outmsg2_offset04 field = "05", outmsg2_offset05 field = "06", outmsg2_offset06 field = "07", outmsg2_offset07 field = "08", outmsg2_offset08 field = "09", outmsg2_offset09 field = "10", outmsg2_offset10 field = "11", outmsg2_offset11 field = "12", outmsg2_offset12 field = "13", outmsg2_offset13 field = "14", outmsg2_offset14 field = "15", outmsg2_offset15 field = "16", outmsg2_offset16 dialog = outmsg2_size, "", yAxis field = " Size" field = "", outmsg2_size01 field = "", outmsg2_size02 field = "", outmsg2_size03 field = "", outmsg2_size04 field = "", outmsg2_size05 field = "", outmsg2_size06 field = "", outmsg2_size07 field = "", outmsg2_size08 field = "", outmsg2_size09 field = "", outmsg2_size10 field = "", outmsg2_size11 field = "", outmsg2_size12 field = "", outmsg2_size13 field = "", outmsg2_size14 field = "", outmsg2_size15 field = "", outmsg2_size16 dialog = outmsg2, "Outmsg 2", xAxis panel = outmsg2_off panel = outmsg2_size dialog = outmsg3_off, "", yAxis field = "Variable Offset" field = "01", outmsg3_offset01 field = "02", outmsg3_offset02 field = "03", outmsg3_offset03 field = "04", outmsg3_offset04 field = "05", outmsg3_offset05 field = "06", outmsg3_offset06 field = "07", outmsg3_offset07 field = "08", outmsg3_offset08 field = "09", outmsg3_offset09 field = "10", outmsg3_offset10 field = "11", outmsg3_offset11 field = "12", outmsg3_offset12 field = "13", outmsg3_offset13 field = "14", outmsg3_offset14 field = "15", outmsg3_offset15 field = "16", outmsg3_offset16 dialog = outmsg3_size, "", yAxis field = " Size" field = "", outmsg3_size01 field = "", outmsg3_size02 field = "", outmsg3_size03 field = "", outmsg3_size04 field = "", outmsg3_size05 field = "", outmsg3_size06 field = "", outmsg3_size07 field = "", outmsg3_size08 field = "", outmsg3_size09 field = "", outmsg3_size10 field = "", outmsg3_size11 field = "", outmsg3_size12 field = "", outmsg3_size13 field = "", outmsg3_size14 field = "", outmsg3_size15 field = "", outmsg3_size16 dialog = outmsg3, "Outmsg 3", xAxis panel = outmsg3_off panel = outmsg3_size dialog = outmsg4_off, "", yAxis field = "Variable Offset" field = "01", outmsg4_offset01 field = "02", outmsg4_offset02 field = "03", outmsg4_offset03 field = "04", outmsg4_offset04 field = "05", outmsg4_offset05 field = "06", outmsg4_offset06 field = "07", outmsg4_offset07 field = "08", outmsg4_offset08 field = "09", outmsg4_offset09 field = "10", outmsg4_offset10 field = "11", outmsg4_offset11 field = "12", outmsg4_offset12 field = "13", outmsg4_offset13 field = "14", outmsg4_offset14 field = "15", outmsg4_offset15 field = "16", outmsg4_offset16 dialog = outmsg4_size, "", yAxis field = " Size" field = "", outmsg4_size01 field = "", outmsg4_size02 field = "", outmsg4_size03 field = "", outmsg4_size04 field = "", outmsg4_size05 field = "", outmsg4_size06 field = "", outmsg4_size07 field = "", outmsg4_size08 field = "", outmsg4_size09 field = "", outmsg4_size10 field = "", outmsg4_size11 field = "", outmsg4_size12 field = "", outmsg4_size13 field = "", outmsg4_size14 field = "", outmsg4_size15 field = "", outmsg4_size16 dialog = outmsg4, "Outmsg 4", xAxis panel = outmsg4_off panel = outmsg4_size dialog = fuelcalc_gauges1, "", xAxis gauge = veGauge1 gauge = veGauge2 gauge = reqfuelGauge gauge = deadtime1Gauge gauge = stoichGauge dialog = fuelcalc_gauges2, "", xAxis gauge = warmupgauge gauge = barocorgauge gauge = gammaairGauge gauge = fuelcorr gauge = afr1targetGauge dialog = fuelcalc_gauges3, "", xAxis gauge = accelEnrichGauge gauge = accEnrichMSGauge gauge = EAEGauge1 gauge = EAEGauge2 gauge = fuelloadGauge gauge = nitrous_addfuel dialog = fuelcalc_gauges3, "", xAxis gauge = fueltemp_cor gauge = fuelpress_cor gauge = ltt_cor gauge = als_addfuel dialog = fuelcalc_gauges4, "", xAxis gauge = pulseWidth1Gauge gauge = pulseWidth2Gauge ; gauge = pulseWidth3Gauge ; gauge = pulseWidth4Gauge dialog = fuelcalc_gauges5, "", xAxis gauge = dutyCycle1Gauge gauge = dutyCycle2Gauge gauge = gammaEnrichGauge dialog = fuelcalc_gauges6, "" field = "For more information on fuel calculations, see http://www.msextra.com/doc/ms3/fuelcalc.html" dialog = fuelcalcs, "Fuel Calculations Summary", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#fuelsum" panel = fuelcalc_gauges1 panel = fuelcalc_gauges2 panel = fuelcalc_gauges3 panel = fuelcalc_gauges4 panel = fuelcalc_gauges5 panel = fuelcalc_gauges6 dialog = sparkcalc_gauges1, "", xAxis gauge = adv1Gauge gauge = adv2Gauge gauge = adv3Gauge gauge = adv4Gauge gauge = base_advanceGauge dialog = sparkcalc_gauges2, "", xAxis gauge = idle_cor_advanceGauge gauge = coldAdvGauge gauge = mat_retardGauge gauge = flex_advanceGauge dialog = sparkcalc_gauges3, "", xAxis gauge = nitrous_retard gauge = revlim_retardGauge gauge = ext_advanceGauge gauge = knockGauge dialog = sparkcalc_gauges4, "", xAxis gauge = tc_retardGauge gauge = cel_retardGauge gauge = fc_retardGauge gauge = als_timingGauge dialog = sparkcalc_gauges5, "", xAxis gauge = launch_timingGauge gauge = step3_timingGauge gauge = launchvss_retardGauge gauge = advdegGauge dialog = sparkcalcs, "Spark Calculations Summary", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#sparksum" panel = sparkcalc_gauges1 panel = sparkcalc_gauges2 panel = sparkcalc_gauges3 panel = sparkcalc_gauges4 panel = sparkcalc_gauges5 dialog = buts_injspk_label, "", yAxis field = "Enabled -->>" field = "Disabled ->>" dialog = buts_injspk1, "", yAxis commandButton = "1", cmdinjspk1, {(status8 & 0x03) && ((status5 & 1) == 0)} commandButton = "1", cmdinjspk1, {(status8 & 0x03) && (status5 & 1)} dialog = buts_injspk2, "", yAxis commandButton = "2", cmdinjspk2, {(status8 & 0x03) && ((status5 & 2) == 0)} commandButton = "2", cmdinjspk2, {(status8 & 0x03) && (status5 & 2)} dialog = buts_injspk3, "", yAxis commandButton = "3", cmdinjspk3, {(status8 & 0x03) && ((status5 & 4) == 0)} commandButton = "3", cmdinjspk3, {(status8 & 0x03) && (status5 & 4)} dialog = buts_injspk4, "", yAxis commandButton = "4", cmdinjspk4, {(status8 & 0x03) && ((status5 & 8) == 0)} commandButton = "4", cmdinjspk4, {(status8 & 0x03) && (status5 & 8)} dialog = buts_injspk5, "", yAxis commandButton = "5", cmdinjspk5, {(status8 & 0x03) && ((status5 & 16) == 0)} commandButton = "5", cmdinjspk5, {(status8 & 0x03) && (status5 & 16)} dialog = buts_injspk6, "", yAxis commandButton = "6", cmdinjspk6, {(status8 & 0x03) && ((status5 & 32) == 0)} commandButton = "6", cmdinjspk6, {(status8 & 0x03) && (status5 & 32)} dialog = buts_injspk7, "", yAxis commandButton = "7", cmdinjspk7, {(status8 & 0x03) && ((status5 & 64) == 0)} commandButton = "7", cmdinjspk7, {(status8 & 0x03) && (status5 & 64)} dialog = buts_injspk8, "", yAxis commandButton = "8", cmdinjspk8, {(status8 & 0x03) && ((status5 & 128) == 0)} commandButton = "8", cmdinjspk8, {(status8 & 0x03) && (status5 & 128)} dialog = buts_injspk9, "", yAxis commandButton = "9", cmdinjspk9, {(status8 & 0x03) && ((status5 & 0x100) == 0)} commandButton = "9", cmdinjspk9, {(status8 & 0x03) && (status5 & 0x100)} dialog = buts_injspk10, "", yAxis commandButton = "10", cmdinjspk10, {(status8 & 0x03) && ((status5 & 0x200) == 0)} commandButton = "10", cmdinjspk10, {(status8 & 0x03) && (status5 & 0x200)} dialog = buts_injspk11, "", yAxis commandButton = "11", cmdinjspk11, {(status8 & 0x03) && ((status5 & 0x400) == 0)} commandButton = "11", cmdinjspk11, {(status8 & 0x03) && (status5 & 0x400)} dialog = buts_injspk12, "", yAxis commandButton = "12", cmdinjspk12, {(status8 & 0x03) && ((status5 & 0x800) == 0)} commandButton = "12", cmdinjspk12, {(status8 & 0x03) && (status5 & 0x800)} dialog = buts_injspk13, "", yAxis commandButton = "13", cmdinjspk13, {(status8 & 0x03) && ((status5 & 0x1000) == 0)} commandButton = "13", cmdinjspk13, {(status8 & 0x03) && (status5 & 0x1000)} dialog = buts_injspk14, "", yAxis commandButton = "14", cmdinjspk14, {(status8 & 0x03) && ((status5 & 0x2000) == 0)} commandButton = "14", cmdinjspk14, {(status8 & 0x03) && (status5 & 0x2000)} dialog = buts_injspk15, "", yAxis commandButton = "15", cmdinjspk15, {(status8 & 0x03) && ((status5 & 0x4000) == 0)} commandButton = "15", cmdinjspk15, {(status8 & 0x03) && (status5 & 0x4000)} dialog = buts_injspk16, "", yAxis commandButton = "16", cmdinjspk16, {(status8 & 0x03) && ((status5 & 0x8000) == 0)} commandButton = "16", cmdinjspk16, {(status8 & 0x03) && (status5 & 0x8000)} dialog = injspkonoffmaster, "", xAxis commandButton = "Off", cmdskipinjoff, {status8 & 0x03}, clickOnCloseIfEnabled commandButton = "Injectors", cmdskipinjon, {(status8 & 0x03) == 0} commandButton = "Coils", cmdskipspkon, {(status8 & 0x03) == 0} dialog = injspkonoffchans, "Outputs Per cylinder", xAxis panel = buts_injspk_label panel = buts_injspk1 panel = buts_injspk2 panel = buts_injspk3 panel = buts_injspk4 panel = buts_injspk5 panel = buts_injspk6 panel = buts_injspk7 panel = buts_injspk8 #ifdef CYL_12_16_SUPPORT dialog = injspkonoffchans2, "Outputs Per cylinder", xAxis panel = buts_injspk_label panel = buts_injspk9 panel = buts_injspk10 panel = buts_injspk11 panel = buts_injspk12 panel = buts_injspk13 panel = buts_injspk14 panel = buts_injspk15 panel = buts_injspk16 #endif dialog = injspkonofftype, "", yAxis displayOnlyField = "Off", dummyfield, {(status8 & 0x03) == 0} displayOnlyField = "Injector disabling test.", dummyfield, {(status8 & 0x03) == 1} displayOnlyField = "Coil disabling test - beware of plug fouling.", dummyfield, {(status8 & 0x03) == 2} field = "Will not run as expected if running:" field = " - semi-sequential fuel" field = " - wasted spark and only a crank wheel" field = " - a simple distributor input." dialog = injspkonoff, "Inj/Spk Disabling Test Mode", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#injspkonoff" panel = injspkonoffmaster, North panel = injspkonofftype, Center panel = injspkonoffchans, South;, {status8 & 0x03} ; <--- this isn't ungreying #ifdef CYL_12_16_SUPPORT panel = injspkonoffchans2, South;, {status8 & 0x03} ; <--- this isn't ungreying #endif dialog = fp_safety, "" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#fuelsafety" field = "Fuel pressure monitoring must be enabled." field = "Enable Fuel Pressure Safety", fp_opt_safety, {fp_press_in} field = "(Target fuel pressure are set on fuel pressure page.)" displayOnlyField = "Static/Target rail differential pressure", rail_pressure_psig displayOnlyField = "Static/Target rail differential pressure", rail_pressure_kpag field = "Check Above Load", fp_drop_load, {fp_opt_safety && fp_press_in} field = "Check Above RPM", fp_drop_rpm, {fp_opt_safety && fp_press_in} field = "Allowed Pressure Drop", fp_drop_psig, {fp_opt_safety && fp_press_in} field = "Allowed Pressure Drop", fp_drop_kpag, {fp_opt_safety && fp_press_in} field = "Time Allowed At Low Pressure", fp_drop_time, {fp_opt_safety && fp_press_in} field = "See AFR safety for shutdown options" dialog = oilpress_set, "" field = "Oil Pressure Input", oilpress_in field = "Oil Pressure Warning", oilpress_out, {oilpress_in} field = "Set the zero rpm pressures above zero" field = "to ensure lamp is tested on each start." field = "" field = "" field = "" field = "" dialog = oilpress, "Oil Pressure", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#oil" panel = oilpress_set, West panel = oil_curve, East, {oilpress_in} dialog = shiftlight, "Shift Light" field = "Shift Light Output", shiftlight_opt_pins field = "Per Gear Limits", shiftlight_opt_gear, {shiftlight_opt_pins} field = "Limit", shiftlight_limit1, {shiftlight_opt_pins && (shiftlight_opt_gear == 0)} field = "1st Gear Limit", shiftlight_limit1, {shiftlight_opt_pins && shiftlight_opt_gear} field = "2nd Gear Limit", shiftlight_limit2, {shiftlight_opt_pins && shiftlight_opt_gear && (gear_no > 1)} field = "3rd Gear Limit", shiftlight_limit3, {shiftlight_opt_pins && shiftlight_opt_gear && (gear_no > 2)} field = "4th Gear Limit", shiftlight_limit4, {shiftlight_opt_pins && shiftlight_opt_gear && (gear_no > 3)} field = "5th Gear Limit", shiftlight_limit5, {shiftlight_opt_pins && shiftlight_opt_gear && (gear_no > 4)} field = "6th Gear Limit", shiftlight_limit6, {shiftlight_opt_pins && shiftlight_opt_gear && (gear_no > 5)} dialog = hpte1, "" field = "This feature requires Incorporate AFR be enabled" field = "High Power Time Enrichment", hpte_opt_on, {loadStoich} field = "Above Load", hpte_load, {hpte_opt_on && loadStoich} field = "Above RPM", hpte_rpm, {hpte_opt_on && loadStoich} dialog = hpte, "High Power Time Enrichment", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#hpte" panel = hpte1, North panel = hpte_curve, South, {hpte_opt_on && loadStoich} dialog = MAFtable, "MAF Flow Curve", card panel = MAFtable1, Center, { MAFOption_t == 0 } panel = MAFtable1f, Center, { MAFOption_t == 1 } dialog = alt_load, "" field = "Warn on Voltage Difference >", alternator_diff, {alternator_opt_mode && alternator_lampout} field = "Load Monitor Input", alternator_freq_monin, {alternator_opt_mode && (alternator_opt_mode < 4)} field = "Capture Polarity", alternator_freq_moninv, {alternator_opt_mode && (alternator_opt_mode < 4) && alternator_freq_monin} field = "Warn On Load >", alternator_maxload, {alternator_lampout && ((alternator_opt_mode && alternator_freq_monin) || (alternator_opt_mode == 4) || (alternator_opt_mode == 5))} field = "" field = "" dialog = alt_pids, "" field = "Closed-Loop PID settings" field = "Proportional Gain", alternator_Kp, {alternator_opt_mode == 4} field = "Integral Gain", alternator_Ki, {alternator_opt_mode == 4} field = "Derivative Gain", alternator_Kd, {alternator_opt_mode == 4} slider = "Sensitivity", alternator_sensitivity, horizontal, {alternator_opt_mode == 4} dialog = alt_pidorload, "", card panel = alt_load, Center, {alternator_opt_mode != 4} panel = alt_pids, Center, {alternator_opt_mode == 4} dialog = alt_settings_t, "" field = "Control Mode", alternator_opt_mode field = "Control Interval", alternator_ctl_ms, {alternator_opt_mode} field = "Control Output", alternator_controlout, {alternator_opt_mode} field = "Output Polarity", alternator_control_inv, {alternator_opt_mode} field = "Control Frequency", alternator_freq, {(alternator_opt_mode == 3) || (alternator_opt_mode == 4)} field = "Warning Lamp Output", alternator_lampout, {alternator_opt_mode} dialog = alt_settings_b, "" field = "Current Monitor Input", alternator_freq_currin, {alternator_opt_mode} field = "Capture Polarity", alternator_freq_currinv, {alternator_opt_mode && alternator_freq_currin} field = "Start Delay", alternator_startdelay, {alternator_opt_mode} field = "Ramp Up Time", alternator_ramptime, {alternator_opt_mode > 1} field = "Battery Temperature Input", alternator_tempin, {alternator_opt_mode} field = "Charge Mode Target Voltage", alternator_targv, {(alternator_tempin == 0) && alternator_opt_mode} field = "Charge Time", alternator_chargetime, {alternator_opt_mode > 1} field = "Run Mode Target Voltage", alternator_targvr, {alternator_opt_mode > 1} field = "WOT TPS%", alternator_wot, {alternator_opt_mode > 1} field = "WOT Target Voltage", alternator_wotv, {(alternator_opt_mode > 1) && (alternator_wot < 100)} field = "WOT Timeout", alternator_wottimeout, {(alternator_opt_mode > 1) && (alternator_wot < 100)} field = "Over-Run Target Voltage", alternator_overrv, {alternator_opt_mode > 1} dialog = alt_settings, "" panel = alt_settings_t panel = alt_pidorload panel = alt_settings_b dialog = alt_outcurve, "", card panel = alternator_outfreq, Center, {alternator_opt_mode == 2} panel = alternator_outduty, Center, {alternator_opt_mode == 3} panel = alternator_linearise, Center, {alternator_opt_mode == 4} dialog = alt_curves, "", yAxis panel = alternator_tempcurve, North, {alternator_opt_mode && alternator_tempin} panel = alt_outcurve dialog = alternator, "Alternator Control", border panel = alt_settings, West panel = alt_curves, East dialog = eaecombi1top, "", border panel = EAEBSOCcurve, West panel = EAEBAWCcurve, East dialog = eaecombi1bot, "", yAxis liveGraph = eaeGraph, "AE Graph", North graphLine = EAEFuelCorr1 graphLine = afr1 graphLine = TPSdot, "%", -2000, 2000, auto, auto graphLine = MAPdot, "%", -2000, 2000, auto, auto dialog = EAEcombi1, "EAE Sucked/Adhered Coefficients", border panel = eaecombi1top, Center panel = eaecombi1bot, South dialog = ms3_pe_t, "" field = "Do not try to enable an output port that is already in use for another function." dialog = ms3_port_edit_wrap, "", yAxis panel = ms3_port_edit, North panel = ms3_pe_t dialog = fuelpump_set, "" field = "Fuel Pump Mode", fp_opt_mode field = "Control Interval", fp_ctl_ms field = "Fuel Pump Output", fp_out1, {fp_opt_mode} field = "Output Frequency", fp_freq, {fp_opt_mode} field = "Fuel Pump Output Polarity", fp_opt_inv, {fp_opt_mode} field = "Pressure Regulation/Correction", fp_opt_reg, {fp_opt_mode == 0} field = "'Fixed' automatically adjusts fuel PW." field = "Static/Target Rail Differential Pressure", rail_pressure_psig field = "Static/Target Rail Differential Pressure", rail_pressure_kpag field = "Priming Duty", fp_prime_duty, {fp_opt_mode} field = "Off Duty", fp_off_duty, {fp_opt_mode} field = "Minimum Duty", fp_min_duty, {fp_opt_mode} field = "Maximum Duty", fp_max_duty, {fp_opt_mode} field = "Pressure Sensor Input (kPa)", fp_press_in field = "Sensor Type", fp_press_type, {fp_press_in} field = "Temperature Sensor Input", fueltemp1 field = "Temperature Correction", fueltemp1_corr, {fueltemp1} field = "Closed-Loop PID settings" field = "Proportional Gain", fp_Kp, {fp_opt_mode == 2} field = "Integral Gain", fp_Ki, {fp_opt_mode == 2} field = "Derivative Gain", fp_Kd, {fp_opt_mode == 2} dialog = fuelpump, "Fuel Pump and Pressure Control", xAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#fuelpump" panel = fuelpump_set, West panel = fp_dutyTbl, East, {fp_opt_mode == 1} dialog = boostvss_curve, "", card panel = boostvss_duty_curve, Center, { (boost_ctl_settings_on) && (!boost_ctl_settings_cl) && ((boost_vss == 1) || (boost_vss == 2))} panel = boostvss_target_curve, Center, { (boost_ctl_settings_on) && (boost_ctl_settings_cl)&& ((boost_vss == 1) || (boost_vss == 2))} dialog = pwmidle_crank_dutyorsteps_curve, "", card panel = pwmidle_crank_dutyorsteps_dutycurve, Center, {IdleCtl == 2} panel = pwmidle_crank_dutyorsteps_stepscurve, Center, {IdleCtl == 3} dialog = pwmidle_cl_initialvalues, "", card panel = pwmidle_cl_initialvalues_dty, Center, { pwmidle_cl_opts_initvaluetable && (IdleCtl == 2) } panel = pwmidle_cl_initialvalues_stps, Center, { pwmidle_cl_opts_initvaluetable && (IdleCtl == 3) } dialog = idlebins, "", card panel = iacBins, Center, { IdleCtl == 3 } panel = ipwBins, Center, { IdleCtl == 2 } dialog = tcslip_set, "", yAxis field = "0-5V knob Input", tc_knob dialog = tcslip_menu, "Traction Control - External Slip% Input", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#tractionslip" panel = tc_slip_curve panel = tcslip_set dialog = blend1_set, "", yAxis field = "X Axis Parameter", blend_opt1 field = "%VE2. 0% = Fully VE1. 100% = Fully VE2." dialog = blend1menu, "Blend Curve (1)", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#blend1" panel = blend1_curve panel = blend1_set dialog = blend2_set field = "X Axis Parameter", blend_opt2 field = "%Spk2. 0% = Fully Spk1. 100% = Fully Spk2." dialog = blend2menu, "Blend Curve (2)", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#blend2" panel = blend2_curve panel = blend2_set dialog = blend3_set field = "X Axis Parameter", blend_opt3 field = "%VE3/4. 0% = Fully VE1/2. 100% = Fully VE3/4." dialog = blend3menu, "Blend Curve (3)", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#blend3" panel = blend3_curve panel = blend3_set dialog = blend4_set field = "X Axis Parameter", blend_opt4 field = "%Spk3/4. 0% = Fully Spk1/2. 100% = Fully Spk3/4." dialog = blend4menu, "Blend Curve (4)", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#blend4" panel = blend4_curve panel = blend4_set dialog = blend5_set field = "X Axis Parameter", blend_opt5 field = "%AFR2. 0% = Fully AFR1. 100% = Fully AFR2." dialog = blend5menu, "Blend Curve (5)", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#blend5" panel = blend5_curve panel = blend5_set dialog = blend6_set field = "X Axis Parameter", blend_opt6 field = "%Boost2. 0% = Fully Boost1. 100% = Fully Boost2." dialog = blend6menu, "Blend Curve (6)", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#blend6" panel = blend6_curve panel = blend6_set dialog = blend7_set field = "X Axis Parameter", blend_opt7 field = "%Crank%2. 0% = Fully Cranking curve1. 100% = Fully Cranking curve2." dialog = blend7menu, "Blend Curve (7)", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#blend7" panel = blend7_curve panel = blend7_set dialog = airden_words field = "This curve is the whole air density correction exposed in full." field = "It is based on the 'ideal gas law' and typically varies between 125% cold to 75% hot." field = "Firmwares 1.1.x and earlier used an embedded curve and a correction curve on top." dialog = manifoldTempCorr2, "MAT Air Density Table" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#matairden" panel = airden_words panel = airdenCorr dialog = checkengine_l, "Sensor Validation" field = "Sensor Checking", cel_opt_on field = "Light Output", cel_port, {cel_opt_on} field = "CEL Solid/Flash Codes", cel_opt_flash, {cel_opt_on} field = "Light When Not Running", cel_opt_when, {cel_opt_on && cel_port} field = "Ignore Fluctuations For First", cel_runtime, {cel_opt_on} field = "#MAP Sensor Check", cel_opt2_map, {cel_opt_on} field = "Minimum ADC", map_minadc, {cel_opt_on} field = "Maximum ADC", map_maxadc, {cel_opt_on} field = "Minimum Fluctuation", map_var_lower, {cel_opt_on} field = "Maximum Fluctuation", map_var_upper, {cel_opt_on} field = "#MAT Sensor Check", cel_opt2_mat, {cel_opt_on} field = "Minimum ADC", mat_minadc, {cel_opt_on} field = "Maximum ADC", mat_maxadc, {cel_opt_on} field = "Maximum Fluctuation", mat_var_upper, {cel_opt_on} field = "#CLT Sensor Check", cel_opt2_clt, {cel_opt_on} field = "Minimum ADC", clt_minadc, {cel_opt_on} field = "Maximum ADC", clt_maxadc, {cel_opt_on} field = "Maximum Fluctuation", clt_var_upper, {cel_opt_on} field = "#TPS Check", cel_opt2_tps, {cel_opt_on} field = "Minimum ADC", tps_minadc, {cel_opt_on} field = "Maximum ADC", tps_maxadc, {cel_opt_on} field = "Maximum Fluctuation", tps_var_upper, {cel_opt_on} dialog = checkengine_r, "" field = "#Battery Check", cel_opt2_batt, {cel_opt_on} field = "Minimum Voltage", batt_minv, {cel_opt_on} field = "Maximum Voltage", batt_maxv, {cel_opt_on} field = "Maximum Fluctuation", batt_var_upper, {cel_opt_on} field = "#EGO1 Sensor Check", cel_opt2_afr0, {cel_opt_on} field = "Minimum AFR", afr_min, {cel_opt_on} field = "Maximum AFR", afr_max, {cel_opt_on} field = "Minimum Fluctuation", afr_var_lower, {cel_opt_on} field = "Maximum Fluctuation", afr_var_upper, {cel_opt_on} field = "#Sync-Loss Check", cel_opt2_sync, {cel_opt_on} field = "No. Sync Losses Allowed", cel_synctol, {cel_opt_on} field = "#EGT Sensor Check", cel_opt2_egt, {cel_opt_on} field = "Minimum EGT", egt_minvalid, {cel_opt_on} field = "Maximum EGT", egt_maxvalid, {cel_opt_on} field = "Minimum Fluctuation", egt_var_lower, {cel_opt_on} field = "Maximum Fluctuation", egt_var_upper, {cel_opt_on} field = "#Flex Sensor Check", cel_opt3_flex, {cel_opt_on && flexFuel} field = "AFR safety, oil pressure set CEL." field = "" field = "status5 Input", cel_opt_stat, {cel_opt_on} field = "status5 Shows", cel_opt_adc, {cel_opt_on && cel_opt_stat} dialog = limpmode, "Limp Mode" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#limp" field = "MAP Triggers Limp Mode", cel_action1_map, {cel_opt_on && cel_opt2_map} field = "Use Fallback MAP Table", cel_action1_map_an, {cel_opt_on && cel_opt2_map && cel_action1_map} field = "MAT Triggers Limp Mode", cel_action1_mat, {cel_opt_on && cel_opt2_mat} field = "Fallback MAT", cel_mat_default, {cel_opt_on && cel_opt2_mat && cel_action1_mat} field = "CLT Triggers Limp Mode", cel_action1_clt, {cel_opt_on && cel_opt2_clt} field = "Fallback Cold CLT", cel_clt_cold, {cel_opt_on && cel_opt2_clt && cel_action1_clt} field = "Fallback Warmed Up CLT", cel_clt_warm, {cel_opt_on && cel_opt2_clt && cel_action1_clt} field = "Time To Warmup Engine", cel_warmtime, {cel_opt_on && cel_opt2_clt && cel_action1_clt} field = "TPS Triggers Limp Mode", cel_action1_tps, {cel_opt_on && cel_opt2_tps} field = "TPS-accel is disabled in fault conditions" field = "Batt Triggers Limp Mode", cel_action1_batt, {cel_opt_on && cel_opt2_batt} field = "EGO Triggers Limp Mode", cel_action1_ego, {cel_opt_on && cel_opt2_afr0} field = "Flex Triggers Limp Mode", cel_action2_flex, {cel_opt_on && cel_opt3_flex} field = "EGT Triggers Limp Mode", cel_action2_egt, {cel_opt_on && cel_opt2_egt} field = "The following apply in limp mode:" field = "Limp Rev Limit", cel_revlim field = "Limp Boost Limit", cel_overboost field = "Limp Boost Valve Duty", cel_boost_duty field = "Limp Boost Valve2 Duty", cel_boost_duty2 field = "Limp Retard Timing By", cel_retard dialog = checkengine, "Check Engine Light", xAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#cel" panel = checkengine_l panel = checkengine_r dialog = limitsettings, "Gauge and Settings Limits" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#gaugeset" field = "These are the limits for gauges and tuning settings," field = "so that curves and tables are more appropriately scaled." field = "Adjust to suit your engine." field = "They do not directly alter engine behaviour." field = "RPM - Max Display", rpmhigh field = "RPM - Warn level", rpmwarn field = "RPM - Danger level", rpmdang field = "Load/kPa - Max", loadhigh field = "VE Value - Max", vehigh field = "Allow WUE Below 100% (only for LPG)", wue_lpg field = "Preferred Speed Units", prefSpeedUnits field = "Preferred Length Units", prefLengthUnits field = "Air-Cooled Expanded CLT Range", clt_exp ; list of features and what pins they use dialog = iopinlist1, ".", yAxis displayOnlyField = "Main Fuel Outputs", hardware_fuel displayOnlyField = "Inj1, Inj2", hardware_fuel, {hardware_fuel== 0} displayOnlyField = "MS3X InjA, InjB etc.", hardware_fuel, {hardware_fuel} displayOnlyField = "Spark Hardware In Use", hardware_spk displayOnlyField = "LED D14, D16, D15, JS11 etc.", hardware_spk, {hardware_spk== 0} displayOnlyField = "MS3X SpkA, SpkB etc.", hardware_spk, {hardware_spk} displayOnlyField = "Cam Input (If Used)", hardware_cam displayOnlyField = "Tertiary Tach Input", spk_mode3_tach3, {spk_mode0 == 47} displayOnlyField = "Programmable On/Off Output: PM3 - Injection LED D14", psEnabled[0], {psEnabled[0]} displayOnlyField = "Programmable On/Off Output: PM4 - Accel LED D16", psEnabled[1], {psEnabled[1]} displayOnlyField = "Programmable On/Off Output: PM5 - Warmup LED D15", psEnabled[2], {psEnabled[2]} displayOnlyField = "Programmable On/Off Output: PJ0 - IAC2", psEnabled[3], {psEnabled[3]} displayOnlyField = "Programmable On/Off Output: PJ1 - IAC1", psEnabled[4], {psEnabled[4]} displayOnlyField = "Programmable On/Off Output: PJ7 - JS11", psEnabled[5], {psEnabled[5]} displayOnlyField = "Programmable On/Off Output: PP2 - Idle", psEnabled[6], {psEnabled[6]} displayOnlyField = "Programmable On/Off Output: PP3 - Boost", psEnabled[7], {psEnabled[7]} displayOnlyField = "Programmable On/Off Output: PP4 - Nitrous 1", psEnabled[8], {psEnabled[8]} displayOnlyField = "Programmable On/Off Output: PP5 - Nitrous 2", psEnabled[9], {psEnabled[9]} displayOnlyField = "Programmable On/Off Output: PP6 - VVT", psEnabled[10], {psEnabled[10]} displayOnlyField = "Programmable On/Off Output: PP7 - Fidle", psEnabled[11], {psEnabled[11]} displayOnlyField = "Programmable On/Off Output: PT1 - V3 Inj 1", psEnabled[12], {psEnabled[12]} displayOnlyField = "Programmable On/Off Output: PT3 - V3 Inj 2", psEnabled[13], {psEnabled[13]} displayOnlyField = "Programmable On/Off Output: PT5 - JS10", psEnabled[14], {psEnabled[14]} displayOnlyField = "Programmable On/Off Output: PK0 - Tacho", psEnabled[15], {psEnabled[15]} displayOnlyField = "Programmable On/Off Output: PA0 - Inj A", psEnabled[16], {psEnabled[16]} displayOnlyField = "Programmable On/Off Output: PA1 - Inj B", psEnabled[17], {psEnabled[17]} displayOnlyField = "Programmable On/Off Output: PA2 - Inj C", psEnabled[18], {psEnabled[18]} displayOnlyField = "Programmable On/Off Output: PA3 - Inj D", psEnabled[19], {psEnabled[19]} displayOnlyField = "Programmable On/Off Output: PA4 - Inj E", psEnabled[20], {psEnabled[20]} displayOnlyField = "Programmable On/Off Output: PA5 - Inj F", psEnabled[21], {psEnabled[21]} displayOnlyField = "Programmable On/Off Output: PA6 - Inj G", psEnabled[22], {psEnabled[22]} displayOnlyField = "Programmable On/Off Output: PA7 - Inj H", psEnabled[23], {psEnabled[23]} displayOnlyField = "Programmable On/Off Output: PB0 - Spk A", psEnabled[24], {psEnabled[24]} displayOnlyField = "Programmable On/Off Output: PB1 - Spk B", psEnabled[25], {psEnabled[25]} displayOnlyField = "Programmable On/Off Output: PB2 - Spk C", psEnabled[26], {psEnabled[26]} displayOnlyField = "Programmable On/Off Output: PB3 - Spk D", psEnabled[27], {psEnabled[27]} displayOnlyField = "Programmable On/Off Output: PB4 - Spk E", psEnabled[28], {psEnabled[28]} displayOnlyField = "Programmable On/Off Output: PB5 - Spk F", psEnabled[29], {psEnabled[29]} displayOnlyField = "Programmable On/Off Output: PB6 - Spk G", psEnabled[30], {psEnabled[30]} displayOnlyField = "Programmable On/Off Output: PB7 - Spk H", psEnabled[31], {psEnabled[31]} displayOnlyField = "Programmable On/Off Output: CANout01", psEnabled[32], {psEnabled[32]} displayOnlyField = "Programmable On/Off Output: CANout02", psEnabled[33], {psEnabled[33]} displayOnlyField = "Programmable On/Off Output: CANout03", psEnabled[34], {psEnabled[34]} displayOnlyField = "Programmable On/Off Output: CANout04", psEnabled[35], {psEnabled[35]} displayOnlyField = "Programmable On/Off Output: CANout05", psEnabled[36], {psEnabled[36]} displayOnlyField = "Programmable On/Off Output: CANout06", psEnabled[37], {psEnabled[37]} displayOnlyField = "Programmable On/Off Output: CANout07", psEnabled[38], {psEnabled[38]} displayOnlyField = "Programmable On/Off Output: CANout08", psEnabled[39], {psEnabled[39]} displayOnlyField = "Programmable On/Off Output: CANout09", psEnabled[40], {psEnabled[40]} displayOnlyField = "Programmable On/Off Output: CANout10", psEnabled[41], {psEnabled[41]} displayOnlyField = "Programmable On/Off Output: CANout11", psEnabled[42], {psEnabled[42]} displayOnlyField = "Programmable On/Off Output: CANout12", psEnabled[43], {psEnabled[43]} displayOnlyField = "Programmable On/Off Output: CANout13", psEnabled[44], {psEnabled[44]} displayOnlyField = "Programmable On/Off Output: CANout14", psEnabled[45], {psEnabled[45]} displayOnlyField = "Programmable On/Off Output: CANout15", psEnabled[46], {psEnabled[46]} displayOnlyField = "Programmable On/Off Output: CANout16", psEnabled[47], {psEnabled[47]} displayOnlyField = "EGO 1 Port", egoport1 displayOnlyField = "EGO 2 Port", egoport2, {egonum > 1} displayOnlyField = "EGO 3 Port", egoport3, {egonum > 2} displayOnlyField = "EGO 4 Port", egoport4, {egonum > 3} displayOnlyField = "EGO 5 Port", egoport5, {egonum > 4} displayOnlyField = "EGO 6 Port", egoport6, {egonum > 5} displayOnlyField = "EGO 7 Port", egoport7, {egonum > 6} displayOnlyField = "EGO 8 Port", egoport8, {egonum > 7} #ifdef CYL_12_16_SUPPORT displayOnlyField = "EGO 9 Port", egoport9, {egonum > 8} displayOnlyField = "EGO 10 Port", egoport10, {egonum > 9} displayOnlyField = "EGO 11 Port", egoport11, {egonum > 10} displayOnlyField = "EGO 12 Port", egoport12, {egonum > 11} displayOnlyField = "EGO 13 Port", egoport13, {egonum > 12} displayOnlyField = "EGO 14 Port", egoport14, {egonum > 13} displayOnlyField = "EGO 15 Port", egoport15, {egonum > 14} displayOnlyField = "EGO 16 Port", egoport16, {egonum > 15} #endif displayOnlyField = "Generic Sensor 01 Input", sensor01_source, {sensor01_source} displayOnlyField = "Generic Sensor 02 Input", sensor02_source, {sensor02_source} displayOnlyField = "Generic Sensor 03 Input", sensor03_source, {sensor03_source} displayOnlyField = "Generic Sensor 04 Input", sensor04_source, {sensor04_source} displayOnlyField = "Generic Sensor 05 Input", sensor05_source, {sensor05_source} displayOnlyField = "Generic Sensor 06 Input", sensor06_source, {sensor06_source} displayOnlyField = "Generic Sensor 07 Input", sensor07_source, {sensor07_source} displayOnlyField = "Generic Sensor 08 Input", sensor08_source, {sensor08_source} displayOnlyField = "Generic Sensor 09 Input", sensor09_source, {sensor09_source} displayOnlyField = "Generic Sensor 10 Input", sensor10_source, {sensor10_source} displayOnlyField = "Generic Sensor 11 Input", sensor11_source, {sensor11_source} displayOnlyField = "Generic Sensor 12 Input", sensor12_source, {sensor12_source} displayOnlyField = "Generic Sensor 13 Input", sensor13_source, {sensor13_source} displayOnlyField = "Generic Sensor 14 Input", sensor14_source, {sensor14_source} displayOnlyField = "Generic Sensor 15 Input", sensor15_source, {sensor15_source} displayOnlyField = "Generic Sensor 16 Input", sensor16_source, {sensor16_source} displayOnlyField = "EGT 1 Channel", egt1port, { (egt_num > 0) } displayOnlyField = "EGT 2 Channel", egt2port, { (egt_num > 1) } displayOnlyField = "EGT 3 Channel", egt3port, { (egt_num > 2) } displayOnlyField = "EGT 4 Channel", egt4port, { (egt_num > 3) } displayOnlyField = "EGT 5 Channel", egt5port, { (egt_num > 4) } displayOnlyField = "EGT 6 Channel", egt6port, { (egt_num > 5) } displayOnlyField = "EGT 7 Channel", egt7port, { (egt_num > 6) } displayOnlyField = "EGT 8 Channel", egt8port, { (egt_num > 7) } displayOnlyField = "EGT 9 Channel", egt9port, { (egt_num > 8) } displayOnlyField = "EGT 10 Channel", egt10port, { (egt_num > 9) } displayOnlyField = "EGT 11 Channel", egt11port, { (egt_num > 10) } displayOnlyField = "EGT 12 Channel", egt12port, { (egt_num > 11) } displayOnlyField = "EGT 13 Channel", egt13port, { (egt_num > 12) } displayOnlyField = "EGT 14 Channel", egt14port, { (egt_num > 13) } displayOnlyField = "EGT 15 Channel", egt15port, { (egt_num > 14) } displayOnlyField = "EGT 16 Channel", egt16port, { (egt_num > 15) } displayOnlyField = "Knock Input Pin", knkport, { knk_option && !knk_option_an } displayOnlyField = "Internal Knock Module Uses D14,D15,D16,JS11,PM2", knk_option_an, {(knk_option_an == 2)} dialog = iopinlist2, ".", yAxis displayOnlyField = "PWM Idle Output", pwmidle_freq_pin, { (IdleCtl == 1) || (IdleCtl == 2) } displayOnlyField = "PWM Idle 3 Wire Mode", pwmidle_freq_pin3, { (IdleCtl == 2) && pwmidle_freq_pin3 } displayOnlyField = "Fan Control Output", fanctl_settings_pin, { fanctl_settings_on } displayOnlyField = "AC Idle-up Output", ac_idleup_io_out, { ac_idleup_settings && ac_idleup_io_out } displayOnlyField = "AC Idle-up Input", ac_idleup_io_in, { ac_idleup_settings } displayOnlyField = "Realtime Baro Port", rtbaroport, {baroCorr == 2} displayOnlyField = "MAP Voltage Input", mapport, {mapport_t == 0} displayOnlyField = "MAP Frequency Input", mapport_f, {mapport_t == 1} displayOnlyField = "MAP 2nd Port", map2port, {(mapport_t == 0) && (mapport != 7) && map2port} displayOnlyField = "MAF Voltage Input", MAFOption, {(MAFOption_t == 0)} displayOnlyField = "MAF Frequency Input", MAFOption_f, {(MAFOption_t == 1)} displayOnlyField = "Flex Sensor Port", flexport, { flexFuel > 0 } displayOnlyField = "Flex Temperature Input", fueltemp1, {fueltemp1} displayOnlyField = "Tacho Output", tacho_opt3f, { tacho_opt80 } displayOnlyField = "VVT1 Output", vvt_out1, {vvt_opt1_on} displayOnlyField = "VVT2 Output", vvt_out2, {vvt_opt1_on > 1} displayOnlyField = "VVT3 Output", vvt_out3, {vvt_opt1_on > 2} displayOnlyField = "VVT4 Output", vvt_out4, {vvt_opt1_on > 3} displayOnlyField = "VVT1 Input", vvt_opt3_cam1, {0} displayOnlyField = "VVT2 Input", vvt_opt3_cam2, {vvt_opt1_on > 1} displayOnlyField = "VVT3 Input", vvt_opt3_cam3, {vvt_opt1_on > 2} displayOnlyField = "VVT4 Input", vvt_opt3_cam4, {vvt_opt1_on > 3} displayOnlyField = "Fuel Table Switching Input", tsw_pin_f, { f5_0_tsf && (f5_0_tsf_opt == 0) && !(dualfuel_sw_on && dualfuel_sw_fuel)} displayOnlyField = "Spark Table Switching Input", tsw_pin_s, { f5_0_tss && (f5_0_tss_opt == 0) } displayOnlyField = "Req Fuel Switching", tsw_pin_rf, { !(dualfuel_sw_on && dualfuel_sw_rf)} displayOnlyField = "AFR Table Switching", tsw_pin_afr, { !(dualfuel_sw_on && dualfuel_sw_afr)} displayOnlyField = "Stoich Switching", tsw_pin_stoich, { !(dualfuel_sw_on && dualfuel_sw_stoich)} displayOnlyField = "Dual Fuel Input", dualfuel_pin, { dualfuel_sw_on && !dualfuel_opt_mode } displayOnlyField = "Overboost Switching", tsw_pin_ob, { OverBoostOption > 0 } displayOnlyField = "Boost Table Switching", boost_feats_tsw, {boost_ctl_settings_on} displayOnlyField = "Boost Control Output (Mid)", boost_ctl_pins_pwm, {boost_ctl_settings_on && (boost_ctl_pwm < 2)} displayOnlyField = "Boost Control Output (Slow)", boost_ctl_pins, {boost_ctl_settings_on && (boost_ctl_pwm == 2)} displayOnlyField = "Boost Control2 Output (Mid)", boost_ctl_pins_pwm2, {boost_ctl_settings_on && boost_ctl_settings_on2 && (boost_ctl_pwm < 2)} displayOnlyField = "Boost Control2 Output (Slow)", boost_ctl_pins2, {boost_ctl_settings_on && boost_ctl_settings_on2 && (boost_ctl_pwm == 2)} displayOnlyField = "Gen PWM A Output", pwm_opt2_a, {pwm_opt_on_a} displayOnlyField = "Gen PWM B Output", pwm_opt2_b, {pwm_opt_on_b} displayOnlyField = "Gen PWM C Output", pwm_opt2_c, {pwm_opt_on_c} displayOnlyField = "Gen PWM D Output", pwm_opt2_d, {pwm_opt_on_d} displayOnlyField = "Gen PWM E Output", pwm_opt2_e, {pwm_opt_on_e} displayOnlyField = "Gen PWM F Output", pwm_opt2_f, {pwm_opt_on_f} displayOnlyField = "Generic Closed-Loop A Output", generic_pid_pwm_outs_a, {generic_pid_flags_a_on} displayOnlyField = "Generic Closed-Loop B Output", generic_pid_pwm_outs_b, {generic_pid_flags_b_on} displayOnlyField = "WI Pump Output", water_pins_pump, {water_freq_on} displayOnlyField = "WI Valve Output", water_pins_valve, {water_freq_on && water_freq_type} displayOnlyField = "VSS1 Analogue sensor", vss1_an, {vss_opt0_1 == 2} displayOnlyField = "VSS1 Digi Input", vss_opt1, {vss_opt0_1 == 1} displayOnlyField = "VSS1 CAN PWM Port", vss1_pwmseq, {vss_opt1 ==15 && (vss_opt0_1 == 1)} displayOnlyField = "VSS2 Analogue Sensor", vss2_an, {vss_opt0_2 == 2} displayOnlyField = "VSS2 Digi Input", vss_opt2, {vss_opt0_2 == 1} displayOnlyField = "VSS2 CAN PWM Port", vss2_pwmseq, {vss_opt2 ==15 && (vss_opt0_1 == 1)} displayOnlyField = "Shaft Sensor 1", ss_opt1, {ss_opt1} displayOnlyField = "Shaft Sensor 2", ss_opt2, {ss_opt2} displayOnlyField = "VSS Output", vssout_opt, {vssout_opt} displayOnlyField = "Gear Pos. Input", gear_port_an, { (gear_method == 2) } displayOnlyField = "Bike Shifter Input", shift_cut_in, { shift_cut_on } displayOnlyField = "Bike Shifter Output", shift_cut_out, { shift_cut_on } displayOnlyField = "Accelerometer X Input", accXport, {accXport} displayOnlyField = "Accelerometer Y Input", accYport, {accYport} displayOnlyField = "Accelerometer Z Input", accZport, {accZport} displayOnlyField = "SDcard Datalog button", log_style2_but, {log_style_on2 == 2} displayOnlyField = "SDcard LED indicator", log_style_led, {log_style_on2} displayOnlyField = "SDcard Stream Input", log_style3_adc, {log_style_block == 1} displayOnlyField = "Nitrous Stage 1 output - nitrous", n2o1n_pins, { N2Oopt_2 } displayOnlyField = "Nitrous Stage 1 output - fuel", n2o1f_pins, { N2Oopt_2 } displayOnlyField = "Nitrous Enable input on:", N2Oopt_pins, { N2Oopt_2 } displayOnlyField = "Nitrous Stage 2 output - nitrous", n2o2n_pins, { N2Oopt_2 && N2Oopt_3 } displayOnlyField = "Nitrous Stage 2 output - fuel", n2o2f_pins, { N2Oopt_2 && N2Oopt_3 } displayOnlyField = "AFR safety Warning Output", maxafr_opt1_led, { maxafr_opt1_on || egt_conf_action } displayOnlyField = "Internal RTC uses PM1 and PM3", opt142_rtc, {opt142_rtc == 1} displayOnlyField = "Launch Input", launch_opt_pins, { launch_opt_on >0 } displayOnlyField = "Variable launch Input", launch_var_on, { launch_opt_on >0 } displayOnlyField = "3-step Input", launch_3step_in, {launch_opt_on >0 } displayOnlyField = "Anti-Lag Enable Input", als_in_pin, {als_in_pin} displayOnlyField = "ALS On/off Output", als_out_pin, {als_in_pin} displayOnlyField = "ALS PWM Output", als_opt_pwmout, {als_in_pin} displayOnlyField = "ALS Output", als_pwm_opt2, {als_in_pin && als_opt_pwmout} displayOnlyField = "Torque Convertor Lockup", tclu_outpin, {tclu_outpin} displayOnlyField = "TCLU Enable Input", tclu_enablepin, {tclu_outpin} displayOnlyField = "TCLU Brake switch", tclu_brakepin, {tclu_outpin} displayOnlyField = "Staged Injection Relay Output 1", staged_out1, { staged_first_param } displayOnlyField = "Staged Injection Relay Output 2", staged_out2, { staged_first_param } displayOnlyField = "Alternator Control Output", alternator_controlout, {alternator_opt_mode} displayOnlyField = "Alternator Warning Lamp Output", alternator_lampout, {alternator_opt_mode} displayOnlyField = "Load Monitor Input", alternator_freq_monin, {alternator_opt_mode && (alternator_opt_mode < 4)} displayOnlyField = "Battery Current Monitor Input", alternator_freq_currin, {alternator_opt_mode} displayOnlyField = "Battery Temperature Input", alternator_tempin, {alternator_opt_mode} displayOnlyField = "Fuel Pump Output", fp_out1, {fp_opt_mode} displayOnlyField = "Primary Pressure Input", fp_press_in, {fp_press_in} displayOnlyField = "Primary Fuel Temperature Input", fueltemp1, {fueltemp1} displayOnlyField = "Secondary Fuel Pressure Input", dualfuel_press_sens, { dualfuel_sw_on && dualfuel_opt_press} displayOnlyField = "Secondary Fuel Temperature Input", dualfuel_temp_sens, { dualfuel_sw_on && dualfuel_opt_temp} dialog = iopinlist, "Feature List Showing I/O pins", xAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#iopins" panel = iopinlist1, West panel = iopinlist2, East ; now list of pins and what features they are assigned to. dialog = pinusage1, ".", yAxis displayOnlyField = "Injector A", { bitStringValue( portLabels , portusage_a[0] ) } displayOnlyField = "Injector B", { bitStringValue( portLabels , portusage_a[1] ) } displayOnlyField = "Injector C", { bitStringValue( portLabels , portusage_a[2] ) } displayOnlyField = "Injector D", { bitStringValue( portLabels , portusage_a[3] ) } displayOnlyField = "Injector E", { bitStringValue( portLabels , portusage_a[4] ) } displayOnlyField = "Injector F", { bitStringValue( portLabels , portusage_a[5] ) } displayOnlyField = "Injector G", { bitStringValue( portLabels , portusage_a[6] ) } displayOnlyField = "Injector H", { bitStringValue( portLabels , portusage_a[7] ) } displayOnlyField = "Spark A", { bitStringValue( portLabels , portusage_b[0] ) } displayOnlyField = "Spark B", { bitStringValue( portLabels , portusage_b[1] ) } displayOnlyField = "Spark C", { bitStringValue( portLabels , portusage_b[2] ) } displayOnlyField = "Spark D", { bitStringValue( portLabels , portusage_b[3] ) } displayOnlyField = "Spark E", { bitStringValue( portLabels , portusage_b[4] ) } displayOnlyField = "Spark F", { bitStringValue( portLabels , portusage_b[5] ) } displayOnlyField = "Spark G", { bitStringValue( portLabels , portusage_b[6] ) } displayOnlyField = "Spark H", { bitStringValue( portLabels , portusage_b[7] ) } displayOnlyField = "Hardware PWM A", { bitStringValue( portLabels , portusage_pwmscl[1] ) } displayOnlyField = "Hardware PWM B", { bitStringValue( portLabels , portusage_pwmscl[3] ) } dialog = pinusage2, ".", yAxis displayOnlyField = "PE0", { bitStringValue( portLabels , portusage_e[0] ) } displayOnlyField = "PE1", { bitStringValue( portLabels , portusage_e[1] ) } displayOnlyField = "Flex", { bitStringValue( portLabels , portusage_e[2] ) } displayOnlyField = "FP", { bitStringValue( portLabels , portusage_e[4] ) } displayOnlyField = "Tableswitch in", { bitStringValue( portLabels , portusage_h[6] ) } displayOnlyField = "Nitrous in", { bitStringValue( portLabels , portusage_h[7] ) } displayOnlyField = "IAC1", { bitStringValue( portLabels , portusage_j[0] ) } displayOnlyField = "IAC2", { bitStringValue( portLabels , portusage_j[1] ) } displayOnlyField = "JS11", { bitStringValue( portLabels , portusage_j[7] ) } displayOnlyField = "Tacho Out", { bitStringValue( portLabels , portusage_k[0] ) } displayOnlyField = "(PK1)", { bitStringValue( portLabels , portusage_k[1] ) } displayOnlyField = "Launch In", { bitStringValue( portLabels , portusage_k[2] ) } displayOnlyField = "(PK3)", { bitStringValue( portLabels , portusage_k[3] ) } displayOnlyField = "(PK7)", { bitStringValue( portLabels , portusage_k[7] ) } displayOnlyField = "(PM2)", { bitStringValue( portLabels , portusage_m[2] ) } displayOnlyField = "Inject LED", { bitStringValue( portLabels , portusage_m[3] ) } displayOnlyField = "Accel LED", { bitStringValue( portLabels , portusage_m[4] ) } displayOnlyField = "Warmup LED", { bitStringValue( portLabels , portusage_m[5] ) } dialog = pinusage3, ".", yAxis displayOnlyField = "Idle", { bitStringValue( portLabels , portusage_p[2] ) } displayOnlyField = "Boost", { bitStringValue( portLabels , portusage_p[3] ) } displayOnlyField = "Nitrous 1", { bitStringValue( portLabels , portusage_p[4] ) } displayOnlyField = "Nitrous 2", { bitStringValue( portLabels , portusage_p[5] ) } displayOnlyField = "VVT", { bitStringValue( portLabels , portusage_p[6] ) } displayOnlyField = "FIDLE", { bitStringValue( portLabels , portusage_p[7] ) } ; displayOnlyField = "Primary tach", { bitStringValue( portLabels , portusage_t[0] ) } displayOnlyField = "Inj Bank 1", { bitStringValue( portLabels , portusage_t[1] ) } displayOnlyField = "MS3X Cam", { bitStringValue( portLabels , portusage_t[2] ) } displayOnlyField = "Inj Bank 2", { bitStringValue( portLabels , portusage_t[3] ) } displayOnlyField = "PT4", { bitStringValue( portLabels , portusage_t[4] ) } displayOnlyField = "PT5/JS10", { bitStringValue( portLabels , portusage_t[5] ) } displayOnlyField = "Datalog In", { bitStringValue( portLabels , portusage_t[6] ) } ; displayOnlyField = "PT7", { bitStringValue( portLabels , portusage_t[7] ) } displayOnlyField = "EXT_MAP (ADC11)", { bitStringValue( portLabels , portusage_ad0h[3] ) } displayOnlyField = "EGO2 (ADC12)", { bitStringValue( portLabels , portusage_ad0h[4] ) } displayOnlyField = "SPAREADC (ADC13)", { bitStringValue( portLabels , portusage_ad0h[5] ) } displayOnlyField = "MAP (ADC0)", { bitStringValue( portLabels , portusage_ad0l[0] ) } ; displayOnlyField = "ADC1", { bitStringValue( portLabels , portusage_ad0l[1] ) } ; displayOnlyField = "ADC2", { bitStringValue( portLabels , portusage_ad0l[2] ) } ; displayOnlyField = "ADC3", { bitStringValue( portLabels , portusage_ad0l[3] ) } ; displayOnlyField = "ADC4", { bitStringValue( portLabels , portusage_ad0l[4] ) } ; displayOnlyField = "ADC5", { bitStringValue( portLabels , portusage_ad0l[5] ) } displayOnlyField = "JS5 (ADC6)", { bitStringValue( portLabels , portusage_ad0l[6] ) } displayOnlyField = "JS4 (ADC7)", { bitStringValue( portLabels , portusage_ad0l[7] ) } dialog = pinusage4, ".", yAxis displayOnlyField = "CANIN 1", { bitStringValue( portLabels , portusage_canin[0] ) } displayOnlyField = "CANIN 2", { bitStringValue( portLabels , portusage_canin[1] ) } displayOnlyField = "CANIN 3", { bitStringValue( portLabels , portusage_canin[2] ) } displayOnlyField = "CANIN 4", { bitStringValue( portLabels , portusage_canin[3] ) } displayOnlyField = "CANIN 5", { bitStringValue( portLabels , portusage_canin[4] ) } displayOnlyField = "CANIN 6", { bitStringValue( portLabels , portusage_canin[5] ) } displayOnlyField = "CANIN 7", { bitStringValue( portLabels , portusage_canin[6] ) } displayOnlyField = "CANIN 8", { bitStringValue( portLabels , portusage_canin[7] ) } displayOnlyField = "CANPWM 1", { bitStringValue( portLabels , portusage_canpwm[0] ) } displayOnlyField = "CANPWM 2", { bitStringValue( portLabels , portusage_canpwm[1] ) } displayOnlyField = "CANPWM 3", { bitStringValue( portLabels , portusage_canpwm[2] ) } displayOnlyField = "CANPWM 4", { bitStringValue( portLabels , portusage_canpwm[3] ) } displayOnlyField = "CANPWM 5", { bitStringValue( portLabels , portusage_canpwm[4] ) } displayOnlyField = "CANPWM 6", { bitStringValue( portLabels , portusage_canpwm[5] ) } displayOnlyField = "CANPWM 7", { bitStringValue( portLabels , portusage_canpwm[6] ) } displayOnlyField = "CANPWM 8", { bitStringValue( portLabels , portusage_canpwm[7] ) } dialog = pinusage5, ".", yAxis displayOnlyField = "CANOUT 1", { bitStringValue( portLabels , portusage_canout[0] ) } displayOnlyField = "CANOUT 2", { bitStringValue( portLabels , portusage_canout[1] ) } displayOnlyField = "CANOUT 3", { bitStringValue( portLabels , portusage_canout[2] ) } displayOnlyField = "CANOUT 4", { bitStringValue( portLabels , portusage_canout[3] ) } displayOnlyField = "CANOUT 5", { bitStringValue( portLabels , portusage_canout[4] ) } displayOnlyField = "CANOUT 6", { bitStringValue( portLabels , portusage_canout[5] ) } displayOnlyField = "CANOUT 7", { bitStringValue( portLabels , portusage_canout[6] ) } displayOnlyField = "CANOUT 8", { bitStringValue( portLabels , portusage_canout[7] ) } displayOnlyField = "CANOUT 9", { bitStringValue( portLabels , portusage_canout[8] ) } displayOnlyField = "CANOUT 10", { bitStringValue( portLabels , portusage_canout[9] ) } displayOnlyField = "CANOUT 11", { bitStringValue( portLabels , portusage_canout[10] ) } displayOnlyField = "CANOUT 12", { bitStringValue( portLabels , portusage_canout[11] ) } displayOnlyField = "CANOUT 13", { bitStringValue( portLabels , portusage_canout[12] ) } displayOnlyField = "CANOUT 14", { bitStringValue( portLabels , portusage_canout[13] ) } displayOnlyField = "CANOUT 15", { bitStringValue( portLabels , portusage_canout[14] ) } displayOnlyField = "CANOUT 16", { bitStringValue( portLabels , portusage_canout[15] ) } ; dialog = pinusage6, ".", yAxis dialog = pinusage7, ".", yAxis displayOnlyField = "CANADC 1", { bitStringValue( portLabels , portusage_canadc[0] ) } displayOnlyField = "CANADC 2", { bitStringValue( portLabels , portusage_canadc[1] ) } displayOnlyField = "CANADC 3", { bitStringValue( portLabels , portusage_canadc[2] ) } displayOnlyField = "CANADC 4", { bitStringValue( portLabels , portusage_canadc[3] ) } displayOnlyField = "CANADC 5", { bitStringValue( portLabels , portusage_canadc[4] ) } displayOnlyField = "CANADC 6", { bitStringValue( portLabels , portusage_canadc[5] ) } displayOnlyField = "CANADC 7", { bitStringValue( portLabels , portusage_canadc[6] ) } displayOnlyField = "CANADC 8", { bitStringValue( portLabels , portusage_canadc[7] ) } dialog = pinusage8, ".", yAxis displayOnlyField = "CANADC 9", { bitStringValue( portLabels , portusage_canadc[8] ) } displayOnlyField = "CANADC 10", { bitStringValue( portLabels , portusage_canadc[9] ) } displayOnlyField = "CANADC 11", { bitStringValue( portLabels , portusage_canadc[10] ) } displayOnlyField = "CANADC 12", { bitStringValue( portLabels , portusage_canadc[11] ) } displayOnlyField = "CANADC 13", { bitStringValue( portLabels , portusage_canadc[12] ) } displayOnlyField = "CANADC 14", { bitStringValue( portLabels , portusage_canadc[13] ) } displayOnlyField = "CANADC 15", { bitStringValue( portLabels , portusage_canadc[14] ) } displayOnlyField = "CANADC 16", { bitStringValue( portLabels , portusage_canadc[15] ) } dialog = pinusage9, ".", yAxis displayOnlyField = "CANADC 17", { bitStringValue( portLabels , portusage_canadc[16] ) } displayOnlyField = "CANADC 18", { bitStringValue( portLabels , portusage_canadc[17] ) } displayOnlyField = "CANADC 19", { bitStringValue( portLabels , portusage_canadc[18] ) } displayOnlyField = "CANADC 20", { bitStringValue( portLabels , portusage_canadc[19] ) } displayOnlyField = "CANADC 21", { bitStringValue( portLabels , portusage_canadc[20] ) } displayOnlyField = "CANADC 22", { bitStringValue( portLabels , portusage_canadc[21] ) } displayOnlyField = "CANADC 23", { bitStringValue( portLabels , portusage_canadc[22] ) } displayOnlyField = "CANADC 24", { bitStringValue( portLabels , portusage_canadc[23] ) } dialog = pinusage, "I/O Pins List Showing Usage - only works when online", xAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#pinusage" panel = pinusage1, West panel = pinusage2, Center panel = pinusage3, East dialog = pinusagem, "", xAxis panel = pinusage4, West panel = pinusage5, Center ; panel = pinusage6, East dialog = pinusageb, "", xAxis panel = pinusage7, West panel = pinusage8, Center panel = pinusage9, East dialog = pinusagecan, "Expansion I/O Pins List/Usage - only works when online", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#pinusagecan" panel = pinusagem, North panel = pinusageb, South dialog = ase_note field = "The typical range for afterstart is 50% (cold) to 5% (warm)" dialog = nestedasePct, "Afterstart Enrichment (ASE) - Percent Adder" panel = asePct panel = ase_note dialog = nestedasePct2, "Afterstart Enrichment (ASE) - Percent Adder 2" panel = asePct2 panel = ase_note dialog = wc_note field = "For 99% of engines, warmup must have 100% in the final row. Typical maximum is 255% (cold)." dialog = nestedwarmup_curve, "Warmup Enrichment (WUE) - Percent Multiplier" panel = warmup_curve panel = wc_note dialog = nestedwarmup_curve2, "Warmup Enrichment (WUE) - Percent Multiplier 2" panel = warmup_curve2 panel = wc_note dialog = tcsettings, "Traction Control Settings" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#traction" field = "Traction Control", tc_opt_on field = "Method", tc_opt_method, {tc_opt_on} field = "Enable Input", tc_enin, {tc_opt_on} field = "Minimum TPS", tc_mintps, {tc_opt_on} field = "Minimum MAP", tc_minmap, {tc_opt_on && (tc_opt_method == 1)} field = "Minimum VSS", tc_minvss, {tc_opt_on && (tc_opt_method != 2) && (tc_opt_method != 3) } field = "VSS1 = driven, VSS2 = undriven wheels" ; field = "Maximum VSS", tc_maxvss, {tc_opt_on } field = "Slip % Setting", tc_opt_slipcurve, {tc_opt_on && (tc_opt_method == 1)} field = "Slip Threshold", tc_slipthresh, {tc_opt_on && (tc_opt_method == 1) && !tc_opt_slipcurve} field = "Nitrous Control", tc_opt_n2o, {tc_opt_on } field = "Add Fuel To:", tc_opt_bank, {tc_opt_on } field = "When staging bank 1 = primary, bank 2 = secondary" dialog = tc_top, "", xAxis panel = tc_retard_curve, West panel = tc_spkcut_curve, East, {spk_mode0 > 1} dialog = tc_mid, "", xAxis panel = tc_addfuel_curve, West panel = tc_nitrous_curve, East, {N2Oopt_2} dialog = tc_btm, "", xAxis panel = tc_boost_curve, West, {boost_ctl_settings_on && boost_ctl_settings_cl} panel = tc_boost_duty_delta_curve, East, {boost_ctl_settings_on && (boost_ctl_settings_cl != 1)} dialog = tc_curves, "Traction Control Reactions", yAxis panel = tc_top, North panel = tc_mid, Center panel = tc_btm, South dialog = tcluparams, "Torque Convertor Lockup" field = "Output Pin", tclu_outpin field = "Enable Input", tclu_enablepin, {tclu_outpin} field = "Brake Switch", tclu_brakepin, {tclu_outpin} field = "Minimum TPS", tclu_tpsmin, {tclu_outpin} field = "Maximum TPS", tclu_tpsmax, {tclu_outpin} field = "Minimum MAP", tclu_mapmin, {tclu_outpin} field = "Maximum MAP", tclu_mapmax, {tclu_outpin} field = "Use VSS", tclu_opt_vss, {tclu_outpin} field = "Minimum Speed", tclu_vssmin, {tclu_outpin && tclu_opt_vss} field = "Use Gear Value", tclu_opt_gear, {tclu_outpin} field = "Minimum Gear", tclu_gearmin, {tclu_outpin && tclu_opt_gear} field = "Activation Delay", tclu_delay, {tclu_outpin} dialog = vvtct, "" field = "." field = "Input" field = "Polarity" field = "No. Teeth" field = "Output" field = "Minimum" field = "Maximum" field = "Int./Exh." field = "Tooth 1" field = "Tooth 2" field = "More Duty Means" dialog = vvtc1, "" field = "#CAM1" field = "", vvt_opt3_cam1, {vvt_opt1_on} field = "", vvt_opt2_cam1pol,{vvt_opt1_on && ((spk_config_trig2l & 0x3) == 0x3) && (spk_mode0 == 4) && (spk_config_trig2 == 3) && (vvt_opt4_decode ==0 )} field = "", vvt_tth1, {(vvt_opt1_on > 0) && (spk_mode0 == 4)} field = "", vvt_out1, {vvt_opt1_on} field = "", vvt_min_ang1, {vvt_opt1_on && vvt_opt2_pid2} field = "", vvt_max_ang1, {vvt_opt1_on && vvt_opt2_pid2} field = "", vvt_opt5_vvt1, {vvt_opt1_on && vvt_opt2_pid2} field = "", vvt_cam1tth1, {vvt_opt1_on && (vvt_opt4_decode == 1)} field = "", vvt_cam1tth2, {vvt_opt1_on && (vvt_opt4_decode == 1)} field = "", vvt_out1_dir, {vvt_opt1_on && vvt_opt2_pid2} dialog = vvtc2, "" field = "#CAM2" field = "", vvt_opt3_cam2, {(vvt_opt1_on > 1) && vvt_opt2_pid2} field = "", vvt_opt2_cam2pol,{(vvt_opt1_on > 1) && vvt_opt2_pid2} field = "", vvt_tth2, {(vvt_opt1_on > 1) && vvt_opt2_pid2 && (spk_mode0 == 4)} field = "", vvt_out2, {(vvt_opt1_on > 1) && vvt_opt2_pid2} field = "", vvt_min_ang2, {(vvt_opt1_on > 1) && vvt_opt2_pid2} field = "", vvt_max_ang2, {(vvt_opt1_on > 1) && vvt_opt2_pid2} field = "", vvt_opt5_vvt2, {(vvt_opt1_on > 1) && vvt_opt2_pid2} field = "", vvt_cam2tth1, {0} field = "", vvt_cam2tth2, {0} field = "", vvt_out2_dir, {(vvt_opt1_on > 1) && vvt_opt2_pid2} dialog = vvtc3, "" field = "#CAM3" field = "", vvt_opt3_cam3, {(vvt_opt1_on > 2) && vvt_opt2_pid2} field = "", vvt_opt2_cam3pol,{(vvt_opt1_on > 2) && vvt_opt2_pid2} field = "", vvt_tth3, {(vvt_opt1_on > 2) && vvt_opt2_pid2 && (spk_mode0 == 4)} field = "", vvt_out3, {((vvt_opt1_on > 2) || ((vvt_opt1_on == 2) && (vvt_opt4_decode == 2))) && vvt_opt2_pid2} field = "", vvt_min_ang3, {(vvt_opt1_on > 2) && vvt_opt2_pid2} field = "", vvt_max_ang3, {(vvt_opt1_on > 2) && vvt_opt2_pid2} field = "", vvt_opt5_vvt3, {(vvt_opt1_on > 2) && vvt_opt2_pid2} field = "", vvt_cam3tth1, {(vvt_opt1_on > 2) && vvt_opt2_pid2 && (vvt_opt4_decode == 1)} field = "", vvt_cam3tth2, {(vvt_opt1_on > 2) && vvt_opt2_pid2 && (vvt_opt4_decode == 1)} field = "", vvt_out3_dir, {((vvt_opt1_on > 2) || ((vvt_opt1_on == 2) && (vvt_opt4_decode == 2))) && vvt_opt2_pid2} dialog = vvtc4, "" field = "#CAM4" field = "", vvt_opt3_cam4, {(vvt_opt1_on > 2) && vvt_opt2_pid2} field = "", vvt_opt2_cam4pol,{(vvt_opt1_on > 2) && vvt_opt2_pid2} field = "", vvt_tth4, {(vvt_opt1_on > 2) && vvt_opt2_pid2 && (spk_mode0 == 4)} field = "", vvt_out4, {((vvt_opt1_on > 2) || ((vvt_opt1_on == 2) && (vvt_opt4_decode == 2))) && vvt_opt2_pid2} field = "", vvt_min_ang4, {(vvt_opt1_on > 2) && vvt_opt2_pid2} field = "", vvt_max_ang4, {(vvt_opt1_on > 2) && vvt_opt2_pid2} field = "", vvt_opt5_vvt4, {(vvt_opt1_on > 2) && vvt_opt2_pid2} field = "", vvt_cam4tth1, {0} field = "", vvt_cam4tth2, {0} field = "", vvt_out4_dir, {((vvt_opt1_on > 2) || ((vvt_opt1_on == 2) && (vvt_opt4_decode == 2))) && vvt_opt2_pid2} dialog = vvtcams, "Cam Settings", xAxis panel = vvtct panel = vvtc1 panel = vvtc2 panel = vvtc3 panel = vvtc4 dialog = vvtinext, "" field = "." field = "Use Hold Duty" field = "Hold/Neutral Duty" field = "Proportional Gain" field = "Integral Gain" field = "Differential Gain" field = "Table is Advance/Retard" dialog = vvtinexi, "" field = "#Intake" field = "", vvt_opt2_use_hold_intake, {vvt_opt1_on && vvt_opt2_pid2} field = "", vvt_hold_duty, {vvt_opt1_on && vvt_opt2_pid2 && vvt_opt2_use_hold_intake} field = "", vvt_ctl_Kp, {vvt_opt1_on && vvt_opt2_pid2} field = "", vvt_ctl_Ki, {vvt_opt1_on && vvt_opt2_pid2} field = "", vvt_ctl_Kd, {vvt_opt1_on && vvt_opt2_pid2} field = "Advance" dialog = vvtinexe, "" field = "#Exhaust" field = "", vvt_opt2_use_hold_exhaust, { vvt_opt2_pid2 && (vvt_opt5_vvt1 || vvt_opt5_vvt2 || vvt_opt1_on > 2) } field = "", vvt_hold_duty_exh, { vvt_opt2_pid2 && (vvt_opt5_vvt1 || vvt_opt5_vvt2 || vvt_opt1_on > 2) && vvt_opt2_use_hold_exhaust } field = "", vvt_ctl_Kp_exh, { vvt_opt2_pid2 && (vvt_opt5_vvt1 || vvt_opt5_vvt2 || vvt_opt1_on > 2) } field = "", vvt_ctl_Ki_exh, { vvt_opt2_pid2 && (vvt_opt5_vvt1 || vvt_opt5_vvt2 || vvt_opt1_on > 2) } field = "", vvt_ctl_Kd_exh, { vvt_opt2_pid2 && (vvt_opt5_vvt1 || vvt_opt5_vvt2 || vvt_opt1_on > 2) } field = "", vvt_opt1_dir_exhaust, { vvt_opt2_pid2 && (vvt_opt5_vvt1 || vvt_opt5_vvt2 || vvt_opt1_on > 2) } dialog = vvtinex, "PID Parameters", xAxis panel = vvtinext panel = vvtinexi panel = vvtinexe dialog = vvt_test, "Test", xAxis field = "Cam", vvt_opt1_tst, {vvt_opt1_on} field = "Duty", vvt_test_duty, {vvt_opt1_on && vvt_opt1_tst} dialog = vvtl, "" field = "No. VVTs", vvt_opt1_on field = "Cam Decoder", vvt_opt4_decode,{vvt_opt1_on && (spk_mode0 == 4)} field = "Frequency", vvt_opt6_freq, {vvt_opt1_on && vvt_out1} field = "On/off or Variable (PID)", vvt_opt2_pid2, {vvt_opt1_on} field = "Adjust Inj. Timing Based On", vvt_opt5_add1, {vvt_opt1_on} field = "Commanded vs. Actual", vvt_opt5_add2, {vvt_opt1_on && vvt_opt5_add1} field = "Inj. Timing Adjustment", vvt_onoff_ang, {vvt_opt1_on && !vvt_opt2_pid2 && vvt_opt5_add1} field = "Load Y Axis In Tables", vvt_opt7_yaxis, {vvt_opt1_on} field = "Minimum CLT", vvt_minclt, {vvt_opt1_on} field = "VVT Maximum Slew", vvt_slew, {vvt_opt1_on && vvt_opt2_pid2} panel = vvt_test dialog = vvtr, "" field = "Control Interval", vvt_opt1_int, {vvt_opt1_on && vvt_opt2_pid2} field = "Control Interval Time", vvt_ctl_ms, {vvt_opt1_on && vvt_opt2_pid2 && vvt_opt1_int} field = "Range Check Measured Angles", vvt_opt5_err, {vvt_opt1_on && vvt_opt2_pid2} field = "Minimum VVT Duty", vvt_minduty1, {vvt_opt1_on && vvt_opt2_pid2} field = "Maximum VVT Duty", vvt_maxduty1, {vvt_opt1_on && vvt_opt2_pid2} panel = vvtinex dialog = vvtparams2, "VVT Settings", xAxis panel = vvtl panel = vvtr dialog = vvtparams, "VVT Settings", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#vvt" panel = vvtparams2 panel = vvtcams dialog = spk_trimaTblTitle, "Cyl #1" panel = spk_trimaTbl dialog = spk_trimbTblTitle, "Cyl #2" panel = spk_trimbTbl dialog = spk_trimcTblTitle, "Cyl #3" panel = spk_trimcTbl dialog = spk_trimdTblTitle, "Cyl #4" panel = spk_trimdTbl dialog = spk_trimadt, "", xAxis panel = spk_trimaTblTitle panel = spk_trimbTblTitle dialog = spk_trimadb, "", xAxis panel = spk_trimcTblTitle panel = spk_trimdTblTitle dialog = spk_trimad,"Spark Cyl 1-4 Trims" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#spktrim1-4" panel = spk_trimadt panel = spk_trimadb dialog = spk_trimeTblTitle, "Cyl #5" panel = spk_trimeTbl dialog = spk_trimfTblTitle, "Cyl #6" panel = spk_trimfTbl dialog = spk_trimgTblTitle, "Cyl #7" panel = spk_trimgTbl dialog = spk_trimhTblTitle, "Cyl #8" panel = spk_trimhTbl dialog = spk_trimeht, "", xAxis panel = spk_trimeTblTitle panel = spk_trimfTblTitle dialog = spk_trimehb, "", xAxis panel = spk_trimgTblTitle panel = spk_trimhTblTitle dialog = spk_trimeh,"Spark Cyl 5-8 Trims" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#spktrim1-4" panel = spk_trimeht panel = spk_trimehb #if CYL_12_16_SUPPORT dialog = spk_trimiTblTitle, "Cyl #9" panel = spk_trimiTbl dialog = spk_trimjTblTitle, "Cyl #10" panel = spk_trimjTbl dialog = spk_trimkTblTitle, "Cyl #11" panel = spk_trimkTbl dialog = spk_trimlTblTitle, "Cyl #12" panel = spk_trimlTbl dialog = spk_trimilt, "", xAxis panel = spk_trimiTblTitle panel = spk_trimjTblTitle dialog = spk_trimilb, "", xAxis panel = spk_trimkTblTitle panel = spk_trimlTblTitle dialog = spk_trimil,"Spark Cyl 9-12 Trims" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#spktrim1-4" panel = spk_trimilt panel = spk_trimilb dialog = spk_trimmTblTitle, "Cyl #13" panel = spk_trimmTbl dialog = spk_trimnTblTitle, "Cyl #14" panel = spk_trimnTbl dialog = spk_trimoTblTitle, "Cyl #15" panel = spk_trimoTbl dialog = spk_trimpTblTitle, "Cyl #16" panel = spk_trimpTbl dialog = spk_trimmpt, "", xAxis panel = spk_trimmTblTitle panel = spk_trimnTblTitle dialog = spk_trimmpb, "", xAxis panel = spk_trimoTblTitle panel = spk_trimpTblTitle dialog = spk_trimmp,"Spark Cyl 13-16 Trims" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#spktrim1-4" panel = spk_trimmpt panel = spk_trimmpb #endif dialog = inj_trimaTblTitle, "Cyl #1" panel = inj_trimaTbl, Center dialog = inj_trimbTblTitle, "Cyl #2" panel = inj_trimbTbl dialog = inj_trimcTblTitle, "Cyl #3" panel = inj_trimcTbl dialog = inj_trimdTblTitle, "Cyl #4" panel = inj_trimdTbl dialog = inj_trimadt, "", xAxis panel = inj_trimaTblTitle panel = inj_trimbTblTitle dialog = inj_trimadb, "", xAxis panel = inj_trimcTblTitle panel = inj_trimdTblTitle dialog = inj_trimad,"Injector Cyl 1-4 Trims", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#injtrim1-4" panel = inj_trimadt panel = inj_trimadb dialog = inj_trimeTblTitle, "Cyl #5" panel = inj_trimeTbl, Center dialog = inj_trimfTblTitle, "Cyl #6" panel = inj_trimfTbl dialog = inj_trimgTblTitle, "Cyl #7" panel = inj_trimgTbl dialog = inj_trimhTblTitle, "Cyl #8" panel = inj_trimhTbl dialog = inj_trimeht, "", xAxis panel = inj_trimeTblTitle panel = inj_trimfTblTitle dialog = inj_trimehb, "", xAxis panel = inj_trimgTblTitle panel = inj_trimhTblTitle dialog = inj_trimeh,"Injector Cyl 5-7 Trims", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#injtrim1-4" panel = inj_trimeht panel = inj_trimehb #if CYL_12_16_SUPPORT dialog = inj_trimiTblTitle, "Cyl #9" panel = inj_trimiTbl dialog = inj_trimjTblTitle, "Cyl #10" panel = inj_trimjTbl dialog = inj_trimkTblTitle, "Cyl #11" panel = inj_trimkTbl dialog = inj_trimlTblTitle, "Cyl #12" panel = inj_trimlTbl dialog = inj_trimilt, "", xAxis panel = inj_trimiTblTitle panel = inj_trimjTblTitle dialog = inj_trimilb, "", xAxis panel = inj_trimkTblTitle panel = inj_trimlTblTitle dialog = inj_trimil,"Injector Cyl 9-12 Trims" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#injtrim1-4" panel = inj_trimilt panel = inj_trimilb dialog = inj_trimmTblTitle, "Cyl #13" panel = inj_trimmTbl dialog = inj_trimnTblTitle, "Cyl #14" panel = inj_trimnTbl dialog = inj_trimoTblTitle, "Cyl #15" panel = inj_trimoTbl dialog = inj_trimpTblTitle, "Cyl #16" panel = inj_trimpTbl dialog = inj_trimmpt, "", xAxis panel = inj_trimmTblTitle panel = inj_trimnTblTitle dialog = inj_trimmpb, "", xAxis panel = inj_trimoTblTitle panel = inj_trimpTblTitle dialog = inj_trimmp,"Injector Cyl 13-16 Trims" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#injtrim1-4" panel = inj_trimmpt panel = inj_trimmpb #endif dialog = antilag, "Turbo Anti-Lag (ALS)" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#als" field = "#Caution! Anti-lag is very hard on your turbo" field = "# and engine. Use at your risk." field = "Anti-lag Enable Input", als_in_pin ; field = "Minimum TPS", als_mintps, {als_in_pin} field = "Maximum TPS", als_maxtps, {als_in_pin} field = "Minimum RPM", als_minrpm, {als_in_pin} field = "Maximum RPM", als_maxrpm, {als_in_pin} field = "Maximum MAT", als_maxmat, {als_in_pin} field = "Maximum ALS time", als_maxtime, {als_in_pin} field = "Time Between Activations", als_pausetime,{als_in_pin} field = "Minimum CLT", als_minclt, {als_in_pin} field = "Maximum CLT", als_maxclt, {als_in_pin} field = "Enable Cyclic Fuel Cut", als_opt_fc, {als_in_pin && hardware_fuel && sequential} field = "Fuel cut likely unsafe with Staging" field = "Enable Cyclic Spark Cut", als_opt_sc, {als_in_pin} field = "-" field = "Enable Roving Idle Fuel Cut", als_opt_ri, {als_in_pin} field = "-" field = "Use Idle Valve", als_opt_idle, {als_in_pin} field = "Idle Valve Duty", als_iac_duty, { als_in_pin && als_opt_idle && (IdleCtl == 2) } field = "Idle Valve Steps", als_iac_steps, { als_in_pin && als_opt_idle && (IdleCtl == 3)} field = "-" field = "On/off Output", als_out_pin, {als_in_pin} field = "-" field = "PWM Output", als_opt_pwmout, {als_in_pin} field = "Output Port/Pin", als_pwm_opt2, {als_in_pin && als_opt_pwmout} field = "Output Duty", als_pwm_duty, {als_in_pin && als_opt_pwmout} field = "Frequency", als_pwm_opt_freq, {als_in_pin && als_opt_pwmout} field = "" dialog = als_left1, "Added Fuel %age" panel = als_addfuel_tbl dialog = als_left2, "ALS Timing" panel = als_timing_tbl dialog = als_right1, "Spark Cut %" panel = als_sparkcut_tbl, North, {als_opt_sc} dialog = als_right2, "Fuel Cut %" panel = als_fuelcut_tbl, South, {als_opt_fc && hardware_fuel && sequential}} dialog = antilag_left, "" panel = als_left1, North panel = als_left2, South dialog = antilag_right, "", border panel = als_right1, North panel = als_right2, South dialog = antilagtables, "Turbo Anti-lag Tables", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#alstables" panel = antilag_left, West panel = antilag_right, East dialog = flash_unlock, "Un/Lock Calibrations" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#calunlock" field = "Sensor Calibrations", flashlock field = "Always re-lock after use" dialog = gen_pwm_left_a, "" field = "Enable Generic PWM A", pwm_opt_on_a field = "Output Port/Pin", pwm_opt2_a, {pwm_opt_on_a} field = "Frequency / On-Off", pwm_opt_freq_a, {pwm_opt_on_a} field = "On Above Duty", pwm_onabove_a, {pwm_opt_on_a && (pwm_opt_freq_a == 0)} field = "Off Below Duty", pwm_offbelow_a, {pwm_opt_on_a && (pwm_opt_freq_a == 0)} channelSelector= "Load Axis", pwm_opt_load_a_offset, pwm_opt_load_a_size, {pwm_opt_on_a} field = "Load is Y axis on table, X axis on curve" field = "Table or Curve", pwm_opt_curve_a, {pwm_opt_on_a} field = "CLT/MAT Units", sensor_temp, {0} field = "" field = "" field = "" field = "" field = "" field = "" dialog = gen_pwm_curve_grapha, "", card panel = pwm_duties_Tbl_a, Center, {pwm_opt_on_a && (pwm_opt_curve_a == 0)} panel = pwm_curve_a, Center, {pwm_opt_on_a && pwm_opt_curve_a} dialog = gen_pwm_a, "Generic PWM A", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#genpwm" panel = gen_pwm_left_a, West panel = gen_pwm_curve_grapha, Center dialog = gen_pwm_left_b, "" field = "Enable Generic PWM B", pwm_opt_on_b field = "Output Port/Pin", pwm_opt2_b, {pwm_opt_on_b} field = "Frequency / On-Off", pwm_opt_freq_b, {pwm_opt_on_b} field = "On Above Duty", pwm_onabove_b, {pwm_opt_on_b && (pwm_opt_freq_b == 0)} field = "Off Below Duty", pwm_offbelow_b, {pwm_opt_on_b && (pwm_opt_freq_b == 0)} channelSelector= "Load Axis", pwm_opt_load_b_offset, pwm_opt_load_b_size, {pwm_opt_on_b} field = "Load is Y axis on table, X axis on curve" field = "Table or Curve", pwm_opt_curve_b, {pwm_opt_on_b} field = "CLT/MAT Units", sensor_temp, {0} field = "" field = "" field = "" field = "" field = "" field = "" dialog = gen_pwm_curve_graphb, "", card panel = pwm_duties_Tbl_b, Center, {pwm_opt_on_b && (pwm_opt_curve_b == 0)} panel = pwm_curve_b, Center, {pwm_opt_on_b && pwm_opt_curve_b} dialog = gen_pwm_b, "Generic PWM B", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#genpwm" panel = gen_pwm_left_b, West panel = gen_pwm_curve_graphb, Center dialog = gen_pwm_left_c, "" field = "Enable Generic PWM C", pwm_opt_on_c field = "Output Port/Pin", pwm_opt2_c, {pwm_opt_on_c} field = "Frequency / On-Off", pwm_opt_freq_c, {pwm_opt_on_c} field = "On Above Duty", pwm_onabove_c, {pwm_opt_on_c && (pwm_opt_freq_c == 0)} field = "Off Below Duty", pwm_offbelow_c, {pwm_opt_on_c && (pwm_opt_freq_c == 0)} channelSelector= "Load Axis", pwm_opt_load_c_offset, pwm_opt_load_c_size, {pwm_opt_on_c} field = "Load is Y axis on table, X axis on curve" field = "Table or Curve", pwm_opt_curve_c, {pwm_opt_on_c} field = "CLT/MAT Units", sensor_temp, {0} field = "" field = "" field = "" field = "" field = "" field = "" dialog = gen_pwm_curve_graphc, "", card panel = pwm_duties_Tbl_c, Center, {pwm_opt_on_c && (pwm_opt_curve_c == 0)} panel = pwm_curve_c, Center, {pwm_opt_on_c && pwm_opt_curve_c} dialog = gen_pwm_c, "Generic PWM C", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#genpwm" panel = gen_pwm_left_c, West panel = gen_pwm_curve_graphc, Center dialog = gen_pwm_left_d, "" field = "Enable Generic PWM D", pwm_opt_on_d field = "Output Port/Pin", pwm_opt2_d, {pwm_opt_on_d} field = "Frequency / On-Off", pwm_opt_freq_d, {pwm_opt_on_d} field = "On Above Duty", pwm_onabove_d, {pwm_opt_on_d && (pwm_opt_freq_d == 0)} field = "Off Below Duty", pwm_offbelow_d, {pwm_opt_on_d && (pwm_opt_freq_d == 0)} channelSelector= "Load Axis", pwm_opt_load_d_offset, pwm_opt_load_d_size, {pwm_opt_on_d} field = "Load is Y axis on table, X axis on curve" field = "Table or Curve", pwm_opt_curve_d, {pwm_opt_on_d} field = "CLT/MAT Units", sensor_temp, {0} field = "" field = "" field = "" field = "" field = "" field = "" dialog = gen_pwm_curve_graphd, "", card panel = pwm_duties_Tbl_d, Center, {pwm_opt_on_d && (pwm_opt_curve_d == 0)} panel = pwm_curve_d, Center, {pwm_opt_on_d && pwm_opt_curve_d} dialog = gen_pwm_d, "Generic PWM D", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#genpwm" panel = gen_pwm_left_d, West panel = gen_pwm_curve_graphd, Center dialog = gen_pwm_left_e, "" field = "Enable Generic PWM E", pwm_opt_on_e field = "Output Port/Pin", pwm_opt2_e, {pwm_opt_on_e} field = "Frequency / On-Off", pwm_opt_freq_e, {pwm_opt_on_e} field = "On Above Duty", pwm_onabove_e, {pwm_opt_on_e && (pwm_opt_freq_e == 0)} field = "Off Below Duty", pwm_offbelow_e, {pwm_opt_on_e && (pwm_opt_freq_e == 0)} channelSelector= "Load Axis", pwm_opt_load_e_offset, pwm_opt_load_e_size, {pwm_opt_on_e} field = "Load is Y axis on table, X axis on curve" field = "Table or Curve", pwm_opt_curve_e, {pwm_opt_on_e} field = "CLT/MAT Units", sensor_temp, {0} field = "" field = "" field = "" field = "" field = "" field = "" dialog = gen_pwm_curve_graphe, "", card panel = pwm_duties_Tbl_e, Center, {pwm_opt_on_e && (pwm_opt_curve_e == 0)} panel = pwm_curve_e, Center, {pwm_opt_on_e && pwm_opt_curve_e} dialog = gen_pwm_e, "Generic PWM E", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#genpwm" panel = gen_pwm_left_e, West panel = gen_pwm_curve_graphe, Center dialog = gen_pwm_left_f, "" field = "Enable Generic PWM F", pwm_opt_on_f field = "Output Port/Pin", pwm_opt2_f, {pwm_opt_on_f} field = "Frequency / On-Off", pwm_opt_freq_f, {pwm_opt_on_f} field = "On Above Duty", pwm_onabove_f, {pwm_opt_on_f && (pwm_opt_freq_f == 0)} field = "Off Below Duty", pwm_offbelow_f, {pwm_opt_on_f && (pwm_opt_freq_f == 0)} channelSelector= "Load Axis", pwm_opt_load_f_offset, pwm_opt_load_f_size, {pwm_opt_on_f} field = "Load is Y axis on table, X axis on curve" field = "Table or Curve", pwm_opt_curve_f, {pwm_opt_on_f} field = "CLT/MAT Units", sensor_temp, {0} field = "" field = "" field = "" field = "" field = "" field = "" dialog = gen_pwm_curve_graphf, "", card panel = pwm_duties_Tbl_f, Center, {pwm_opt_on_f && (pwm_opt_curve_f == 0)} panel = pwm_curve_f, Center, {pwm_opt_on_f && pwm_opt_curve_f} dialog = gen_pwm_f, "Generic PWM F", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#genpwm" panel = gen_pwm_left_f, West panel = gen_pwm_curve_graphf, Center dialog = map_sample_dialog_south, "MAP Sample General Settings" field = "MAP Sample Method", mapsample_opt2 field = "Map Sample Window", map_sample_duration, { !mapsample_opt2 } field = "No. Sample Events", mapsample_opt1, { !mapsample_opt2 } field = "" field = "Phase Detect Threshold", map_phase_thresh, { (nCylinders < 3) && (hardware_cam == 2) && (spk_mode0 == 4) && (spk_config_trig2 == 3) } dialog = map_sample_dialog, "MAP Sample Settings", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#mapsamp" panel = mapsample_curve, Center, { !mapsample_opt2 } panel = map_sample_dialog_south, South dialog = ShiftSettings, "Sequential Shift Cut" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#seqshift" field = "Shifter Spark Cut System", shift_cut_on field = "Mode", shift_cut_auto, { shift_cut_on } field = "Button Input", shift_cut_in, { shift_cut_on } field = "Solenoid Output", shift_cut_out, { shift_cut_on } field = "RPM >", shift_cut_rpm, { shift_cut_on } field = "And TPS >", shift_cut_tps, { shift_cut_on } field = "Delay Before Spark Cut", shift_cut_delay, { shift_cut_on } field = "Spark Cut Time (Base)", shift_cut_time, { shift_cut_on } field = "Gear Based Delay", shift_cut_gear, { shift_cut_on } field = "Additional Delay 1-2", shift_cut_add12, { shift_cut_on && shift_cut_gear } field = "Additional Delay 2-3", shift_cut_add23, { shift_cut_on && shift_cut_gear } field = "Additional Delay 3-4", shift_cut_add34, { shift_cut_on && shift_cut_gear } field = "Additional Delay 4-5", shift_cut_add45, { shift_cut_on && shift_cut_gear } field = "Additional Delay 5-6", shift_cut_add56, { shift_cut_on && shift_cut_gear } field = "Solenoid Delay", shift_cut_soldelay, { shift_cut_on && shift_cut_on} field = "Re-Shift Hold-Off Time", shift_cut_reshift field = "Automatic mode shift points" field = "Shift RPM 1-2", shift_cut_rpm12, { shift_cut_on && shift_cut_auto } field = "Shift RPM 2-3", shift_cut_rpm23, { shift_cut_on && shift_cut_auto } field = "Shift RPM 3-4", shift_cut_rpm34, { shift_cut_on && shift_cut_auto } field = "Shift RPM 4-5", shift_cut_rpm45, { shift_cut_on && shift_cut_auto } field = "Shift RPM 5-6", shift_cut_rpm56, { shift_cut_on && shift_cut_auto } dialog = fan_control, "Fan Control" field = "Fan Control On", fanctl_settings_on field = "Fan Control Idles up?", fanctl_settings_idleup, { fanctl_settings_on } field = "Output Pin", fanctl_settings_pin, { fanctl_settings_on } field = "Idle-up Delay", fanctl_idleup_delay, { fanctl_settings_on && fanctl_settings_idleup } field = "Idle-up Duty", fanctl_idleup_adder_duty, { fanctl_settings_on && fanctl_settings_idleup && (IdleCtl == 2) } field = "Idle-up Steps", fanctl_idleup_adder_steps, { fanctl_settings_on && fanctl_settings_idleup && (IdleCtl == 3) } field = "Idle-up Target Increase", fan_idleup_cl_targetadder, { ac_idleup_settings && (IdleCtl > 1) && (IdleCtl_alg == 1) } field = "Fan On Temperature", fanctl_ontemp, { fanctl_settings_on } field = "Fan Off Temperature", fanctl_offtemp, { fanctl_settings_on } field = "Allow fan When Engine Off", fanctl_opt2_engineoff, { fanctl_settings_on } field = "Fan On With AC On?", fan_ctl_settings_acfan, { fanctl_settings_on && ac_idleup_settings } field = "Fan Shutoff" field = "TPS Shutoff", fan_idleup_tps_offpoint, { fanctl_settings_on } field = "TPS Hysteresis", fan_idleup_tps_hyst, { fanctl_settings_on } field = "VSS Shutoff", fan_idleup_vss_offpoint, { fanctl_settings_on && (vss_opt0_1) } field = "VSS Hyst", fan_idleup_vss_hyst, { fanctl_settings_on && (vss_opt0_1) } dialog = ac_idleup, "Air Conditioning Idle-Up" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#acidle" field = "A/C Idle-Up", ac_idleup_settings field = "Idle-Up Output", ac_idleup_io_out, { ac_idleup_settings } field = "Idle-Up Input", ac_idleup_io_in, { ac_idleup_settings } field = "Idle-Up Delay", ac_idleup_delay, { ac_idleup_settings } field = "Idle-Up Min RPM", ac_idleup_min_rpm, { ac_idleup_settings } field = "Compressor delay since last on", ac_delay_since_last_on, { ac_idleup_settings } field = "Idle-up Duty", ac_idleup_adder_duty, { (IdleCtl == 2) && ac_idleup_settings } field = "Idle-up Steps", ac_idleup_adder_steps, { (IdleCtl == 3) && ac_idleup_settings } field = "Idle-up Target RPM Adder", ac_idleup_cl_targetadder, { ac_idleup_settings && (IdleCtl > 1) && (IdleCtl_alg == 1) } field = "Idle-up CL load Allowance", ac_idleup_cl_lockout_mapadder, { ac_idleup_settings && (IdleCtl > 1) && (IdleCtl_alg == 1) } field = "A/C compressor Shutoff" field = "TPS Shutoff", ac_idleup_tps_offpoint, { ac_idleup_settings } field = "TPS Hysteresis", ac_idleup_tps_hyst, { ac_idleup_settings } field = "VSS Shutoff", ac_idleup_vss_offpoint, { ac_idleup_settings && (vss_opt0_1) } field = "VSS Hysteresis", ac_idleup_vss_hyst, { ac_idleup_settings && (vss_opt0_1) } dialog = sensor_source, "", yAxis field = "Sensor - Source" field = "01", sensor01_source field = "02", sensor02_source field = "03", sensor03_source field = "04", sensor04_source field = "05", sensor05_source field = "06", sensor06_source field = "07", sensor07_source field = "08", sensor08_source dialog = sensor_sourceb, "", yAxis field = "Sensor - Source" field = "09", sensor09_source field = "10", sensor10_source field = "11", sensor11_source field = "12", sensor12_source field = "13", sensor13_source field = "14", sensor14_source field = "15", sensor15_source field = "16", sensor16_source dialog = sensor_alias, "", yAxis field = "Field Name" field = "", sensor01Alias field = "", sensor02Alias field = "", sensor03Alias field = "", sensor04Alias field = "", sensor05Alias field = "", sensor06Alias field = "", sensor07Alias field = "", sensor08Alias dialog = sensor_aliasb, "", yAxis field = "Field Name" field = "", sensor09Alias field = "", sensor10Alias field = "", sensor11Alias field = "", sensor12Alias field = "", sensor13Alias field = "", sensor14Alias field = "", sensor15Alias field = "", sensor16Alias dialog = sensor_trans, "", yAxis field = "Transformation" field = "", sensor01_trans, {sensor01_source} field = "", sensor02_trans, {sensor02_source} field = "", sensor03_trans, {sensor03_source} field = "", sensor04_trans, {sensor04_source} field = "", sensor05_trans, {sensor05_source} field = "", sensor06_trans, {sensor06_source} field = "", sensor07_trans, {sensor07_source} field = "", sensor08_trans, {sensor08_source} dialog = sensor_transb, "", yAxis field = "Transformation" field = "", sensor09_trans, {sensor09_source} field = "", sensor10_trans, {sensor10_source} field = "", sensor11_trans, {sensor11_source} field = "", sensor12_trans, {sensor12_source} field = "", sensor13_trans, {sensor13_source} field = "", sensor14_trans, {sensor14_source} field = "", sensor15_trans, {sensor15_source} field = "", sensor16_trans, {sensor16_source} dialog = sensor_val0, "", yAxis field = "0V value" field = "", sensor01_val0, {sensor01_source && (sensor01_trans == 1)} field = "", sensor02_val0, {sensor02_source && (sensor02_trans == 1)} field = "", sensor03_val0, {sensor03_source && (sensor03_trans == 1)} field = "", sensor04_val0, {sensor04_source && (sensor04_trans == 1)} field = "", sensor05_val0, {sensor05_source && (sensor05_trans == 1)} field = "", sensor06_val0, {sensor06_source && (sensor06_trans == 1)} field = "", sensor07_val0, {sensor07_source && (sensor07_trans == 1)} field = "", sensor08_val0, {sensor08_source && (sensor08_trans == 1)} dialog = sensor_val0b, "", yAxis field = "0V value" field = "", sensor09_val0, {sensor09_source && (sensor09_trans == 1)} field = "", sensor10_val0, {sensor10_source && (sensor10_trans == 1)} field = "", sensor11_val0, {sensor11_source && (sensor11_trans == 1)} field = "", sensor12_val0, {sensor12_source && (sensor12_trans == 1)} field = "", sensor13_val0, {sensor13_source && (sensor13_trans == 1)} field = "", sensor14_val0, {sensor14_source && (sensor14_trans == 1)} field = "", sensor15_val0, {sensor15_source && (sensor15_trans == 1)} field = "", sensor16_val0, {sensor16_source && (sensor16_trans == 1)} dialog = sensor_max, "", yAxis field = "5V value" field = "", sensor01_max, {sensor01_source && (sensor01_trans == 1)} field = "", sensor02_max, {sensor02_source && (sensor02_trans == 1)} field = "", sensor03_max, {sensor03_source && (sensor03_trans == 1)} field = "", sensor04_max, {sensor04_source && (sensor04_trans == 1)} field = "", sensor05_max, {sensor05_source && (sensor05_trans == 1)} field = "", sensor06_max, {sensor06_source && (sensor06_trans == 1)} field = "", sensor07_max, {sensor07_source && (sensor07_trans == 1)} field = "", sensor08_max, {sensor08_source && (sensor08_trans == 1)} dialog = sensor_maxb, "", yAxis field = "5V value" field = "", sensor09_max, {sensor09_source && (sensor09_trans == 1)} field = "", sensor10_max, {sensor10_source && (sensor10_trans == 1)} field = "", sensor11_max, {sensor11_source && (sensor11_trans == 1)} field = "", sensor12_max, {sensor12_source && (sensor12_trans == 1)} field = "", sensor13_max, {sensor13_source && (sensor13_trans == 1)} field = "", sensor14_max, {sensor14_source && (sensor14_trans == 1)} field = "", sensor15_max, {sensor15_source && (sensor15_trans == 1)} field = "", sensor16_max, {sensor16_source && (sensor16_trans == 1)} dialog = sensor_lag, "", yAxis field = "Lag Factor" field = "", sensor01LF, {sensor01_source} field = "", sensor02LF, {sensor02_source} field = "", sensor03LF, {sensor03_source} field = "", sensor04LF, {sensor04_source} field = "", sensor05LF, {sensor05_source} field = "", sensor06LF, {sensor06_source} field = "", sensor07LF, {sensor07_source} field = "", sensor08LF, {sensor08_source} dialog = sensor_lagb, "", yAxis field = "Lag Factor" field = "", sensor09LF, {sensor09_source} field = "", sensor10LF, {sensor10_source} field = "", sensor11LF, {sensor11_source} field = "", sensor12LF, {sensor12_source} field = "", sensor13LF, {sensor13_source} field = "", sensor14LF, {sensor14_source} field = "", sensor15LF, {sensor15_source} field = "", sensor16LF, {sensor16_source} dialog = sensors_top, "Sensors 1-8", xAxis panel = sensor_source panel = sensor_alias panel = sensor_trans panel = sensor_val0 panel = sensor_max panel = sensor_lag dialog = sensors_btm, "Sensors 9-16", xAxis panel = sensor_sourceb panel = sensor_aliasb panel = sensor_transb panel = sensor_val0b panel = sensor_maxb panel = sensor_lagb dialog = sensors_data, "", yAxis panel = sensors_top panel = sensors_btm dialog = sensors_temp, "", xAxis field = "Allow Input Sharing", opt142_gs_share field = "CLT/MAT Units", sensor_temp dialog = sensors, "Generic Sensor Inputs", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#gensens" panel = sensors_data, North panel = sensors_temp, South dialog = ITB_settings, "ITB settings" field = "Percent Baro Switchpoint", ITB_load_mappoint field = "Idle TPS Threshold", ITB_load_idletpsthresh dialog = ITBcombined, "ITB Load Settings", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#itbload" panel = ITB_settings, South panel = ITB_load_switchpoint_curve, West panel = ITB_load_loadvals_curve, East dialog = mafdialog, "MAF Settings", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#mafset" field = "Sensor Type", MAFOption_t field = "Voltage Input Port", MAFOption, {MAFOption_t == 0} field = "Frequency Input Port", MAFOption_f, {MAFOption_t == 1} field = "Low Frequency", maf_freq0, {MAFOption_t == 1} field = "High Frequency", maf_freq1, {MAFOption_t == 1} field = "MAT Correction Curve", feature7_mafmat, {MAFOption_t < 2} field = "Use VE1 As Trim Table", feature7_maftrim, {(algorithm == 5) && (MAFOption_t < 2) } field = "MAF Sensor Range", maf_range, {MAFOption_t < 2} field = "Set the range before loading a flow curve." field = "Use Old-Style Calibration Curve (See Tools Menu)", feature7_mafcalib, {MAFOption_t < 2} dialog = battcalib, "Calibrate Battery Voltage" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#calbatt" field = "Supply Voltage At Zero ADC Count", batt0 field = "Supply voltage At Max ADC Count", battmax field = "" field = "Typical values are 0.0V and 29.7V" dialog = waterinj_topl, "" field = "Enable Water/Meth Injection", water_freq_on field = "Pump Output", water_pins_pump, {water_freq_on} field = "Valve Style", water_freq_type, {water_freq_on} field = "Frequency", water_freq, {water_freq_on && (water_freq_type ==2)} field = "Valve Output", water_pins_valve, {water_freq_on && water_freq_type} dialog = waterinj_topr, "" field = "Enable When.." field = "TPS >", water_tps, {water_freq_on} field = "RPM >", water_rpm, {water_freq_on} field = "MAP >", water_map, {water_freq_on} field = "MAT >", water_mat, {water_freq_on} field = "" field = "Low Fluid Level Input", water_pins_in_shut, {water_freq_on} dialog = waterinj_top, "", border panel = waterinj_topl, West panel = waterinj_topr, East dialog = waterinj, "Water Injection", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#water" panel = waterinj_top, North panel = waterinjTbl, Center dialog = vss1, "Vehicle Speed Sensor 1" field = "VSS1 Input Type", vss_opt0_1 field = "Analogue Input", vss1_an, {vss_opt0_1 == 2} field = "Full Scale Speed", vss1_an_max, {vss_opt0_1 == 2} field = "Digital Input", vss_opt1, {vss_opt0_1 == 1} field = "Wheel Diameter", wheeldia1, {vss_opt1 && (((vss_opt0_1 == 1) && (vss_opt1 != 14) && (vss1_pos < 2)) || (gear_method == 1))} field = "VSS Position/Type", vss1_pos, {vss_opt0_1 == 1} field = "Pulses", vss1_can_scale_pulse, {vss_opt1 && (vss_opt0_1 == 1) && (vss_opt1 != 14) && (vss1_pos > 1)} field = "Speed Sensor #Teeth", reluctorteeth1, {vss_opt1 && (vss_opt0_1 == 1) && (vss_opt1 != 14) && (vss1_pos < 2)} field = "PWM Port", vss1_pwmseq, {(vss_opt1 ==15) && (vss_opt0_1 == 1)} field = "Scaler", vss1_can_scale, {(vss_opt1 ==14) && (vss_opt0_1 == 1)} field = "Smoothing lag factor", vss1LF, {vss_opt0_1} dialog = vss2, "Vehicle speed sensor 2" field = "VSS2 Input Type", vss_opt0_2 field = "Analogue Input", vss2_an, {vss_opt0_2 == 2} field = "Full Scale Speed", vss2_an_max, {vss_opt0_2 == 2} field = "Digital Input", vss_opt2, {vss_opt0_2 == 1} field = "Wheel Diameter", wheeldia2, {vss_opt2 && (((vss_opt0_2 == 1) && (vss_opt2 != 14) && (vss2_pos < 2)) || (gear_method == 1))} field = "VSS Position/Type", vss2_pos, {vss_opt0_2 == 1} field = "Pulses", vss2_can_scale_pulse, {vss_opt2 && (vss_opt0_2 == 1) && (vss_opt2 != 14) && (vss2_pos > 1)} field = "Speed Sensor #Teeth", reluctorteeth2, {vss_opt2 && (vss_opt0_2 == 1) && (vss_opt2 != 14) && (vss2_pos < 2)} field = "PWM Port", vss2_pwmseq, {(vss_opt2 ==15) && (vss_opt0_2 == 1)} field = "Scaler", vss2_can_scale, {(vss_opt2 ==14) && (vss_opt0_2 == 1)} field = "Smoothing Lag Factor", vss2LF, {vss_opt0_2} dialog = vss3, "Vehicle Speed Sensor 3 (Matches VSS1)" field = "VSS3 Input Type", vss_opt0_3, {vss_opt0_1} field = "Analogue Input", vss3_an, {vss_opt0_3 && (vss_opt0_1 == 2)} field = "Digital Input", vss_opt3, {vss_opt0_3 && (vss_opt0_1 == 1)} field = "PWM Port", vss3_pwmseq, {(vss_opt3 ==15) && vss_opt0_3 && (vss_opt0_1 == 1)} dialog = vss4, "Vehicle speed sensor 4 (matches VSS2)" field = "VSS4 input type", vss_opt0_4, {vss_opt0_2} field = "Analogue Input", vss4_an, {vss_opt0_4 && (vss_opt0_2 == 2)} field = "Digital Input", vss_opt4, {vss_opt0_4 && (vss_opt0_2 == 1)} field = "PWM Port", vss4_pwmseq, {(vss_opt4 ==15) && vss_opt0_4 && (vss_opt0_4 == 1)} dialog = vssout, "VSS Output" field = "VSS Output", vssout_opt field = "VSSout Units", vssout_optunits, { vssout_opt } field = "Scale", vssout_scale, { vssout_opt } dialog = vssdotlag, "VSSdot Smoothing" field = "Sample Interval", vssdot_int field = "Lag factor", vssdotLF dialog = gears, "Gear detection" field = "Final Drive Ratio", fdratio1 field = "Method", gear_method field = "Number Of Gears", gear_no, {gear_method} field = "1st Ratio", gear1ratio, { (gear_method == 1) } field = "2nd Ratio", gear2ratio, { (gear_method == 1) && (gear_no > 1) } ; would be pretty pointless otherwise! field = "3rd Ratio", gear3ratio, { (gear_method == 1) && (gear_no > 2) } field = "4th Ratio", gear4ratio, { (gear_method == 1) && (gear_no > 3) } field = "5th Ratio", gear5ratio, { (gear_method == 1) && (gear_no > 4) } field = "6th Ratio", gear6ratio, { (gear_method == 1) && (gear_no > 5) } field = "" field = "Input Port", gear_port_an, { (gear_method == 2) } field = "Neutral Voltage", gear0v, { (gear_method == 2) } field = "1st Gear Voltage", gear1v, { (gear_method == 2) } field = "2nd Gear Voltage", gear2v, { (gear_method == 2) && (gear_no > 1) } field = "3rd Gear Voltage", gear3v, { (gear_method == 2) && (gear_no > 2) } field = "4th Gear Voltage", gear4v, { (gear_method == 2) && (gear_no > 3) } field = "5th Gear Voltage", gear5v, { (gear_method == 2) && (gear_no > 4) } field = "6th Gear Voltage", gear6v, { (gear_method == 2) && (gear_no > 5) } dialog = vssunits, "Units" field = "Preferred Speed Units", prefSpeedUnits field = "Preferred Length Units", prefLengthUnits dialog = ssnorth, "", border panel = vss1, West panel = vss2, East dialog = vss34, "", border panel = vss3, West panel = vss4, East dialog = gearsunits, "", border panel = gears, North panel = vssunits, South dialog = vssoutdot, "", border panel = vssout, West panel = vssdotlag, East dialog = sssouth, "", border panel = vss34, North panel = vssoutdot, South dialog = speedsensorsmain, "", yAxis panel = ssnorth panel = sssouth dialog = speedsensors, "Speed and Gear Sensors", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#speedgear" panel = speedsensorsmain, West panel = gearsunits, East dialog = ss, "Shaft Speed Sensors" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#shaftspeed" field = "Sensor 1", ss_opt1 field = "Speed sensor #teeth", reluctorteeth3, {ss_opt1 && ss_opt1<15} field = "High Speed Input", ss_opt1_spd, {(ss_opt1 == 4) || (ss_opt1 == 10) || (ss_opt1 == 11) || (ss_opt1 == 12)} field = "Smoothing Lag Factor", ss1LF ;, {ss_opt2 && ss_opt2<15} field = "" field = "Sensor 2", ss_opt2 field = "Speed Sensor #Teeth", reluctorteeth4, {ss_opt2 && ss_opt2<15} field = "High Speed Input", ss_opt2_spd, {(ss_opt2 == 4) || (ss_opt2 == 10) || (ss_opt2 == 11) || (ss_opt2 == 12)} field = "Smoothing Lag Factor", ss2LF ;, {ss_opt2 && ss_opt2<15} dialog = accelerometer, "Accelerometer Parameters" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#accelerometer" field = "X Input", accXport field = "Y Input", accYport field = "Z Input", accZport field = "X -1g Calib.", accXcal1, { accXport } field = "X +1g Calib.", accXcal2, { accXport } field = "Y -1g Calib.", accYcal1, { accYport } field = "Y +1g Calib.", accYcal2, { accYport } field = "Z -1g Calib.", accZcal1, { accZport } field = "Z +1g Calib.", accZcal2, { accZport } field = "Lag factor", accxyzLF dialog = sdcard_top, "" field = "SD Card Logging:", log_style_on2 field = "Datalog Button", log_style2_but, {log_style_on2 == 2} field = "Trigger", log_style4_opt, {log_style_on2 == 3} field = "RPM >", log_trig_rpm, {(log_style_on2 == 3) && (log_style4_opt == 0)} field = "TPS >", log_trig_tps, {(log_style_on2 == 3) && (log_style4_opt == 1)} field = "LED Indicator", log_style_led, {log_style_on2} field = "Log Data Block Size", log_style_block, {log_style_on2} field = "Interleave GPS Data", log_style_gps, {log_style_on2} field = "Sampling", log_style2_samp, {(log_style_block != 1) && log_style_on2 } field = "Sample Interval", log_int, {(log_style_block != 1) && log_style_on2 } displayOnlyField = "Frames/Second", log_rate, {(log_style_block != 1) && log_style_on2 } field = "Log File Max Duration", log_length, {log_style_on2} field = "Stream Input", log_style3_adc, {log_style_block == 1} field = "SPI Comms Speed", log_style_ledspd, {log_style_on2} dialog = sdcard_btm, "" logFieldSelector = dataLogFieldSelector, "Log Field Selection", logFieldOffset, logFieldLength, 55 dialog = sdcard_datalog, "SD Card Datalogging", yAxis panel = sdcard_top panel = dataLogFieldSelector dialog = N2OSystem_topl, "" field = "Nitrous Control", N2Oopt_2 field = "Enable N2O When Above", N2ORpm, { N2Oopt_2 } field = "And Coolant Temp Above", N2OClt, { N2Oopt_2 } field = "And TPS >", N2OTps, { N2Oopt_2 } field = "Max RPM", N2ORpmMax, { N2Oopt_2 } field = "Enrich Which Bank", N2Oopt_01, { N2Oopt_2 } dialog = N2OSystem_topr, "" field = "On/Off vs Progressive Mode", N2Oopt2_prog, { N2Oopt_2 } field = "Time-Based or RPM-Based", N2Oopt2_prog_time, { N2Oopt_2 && N2Oopt2_prog } field = "Solenoid Frequency", N2Oopt2_prog_freq, { N2Oopt_2 && N2Oopt2_prog } field = "AFR Safety Uses AFR2 Targets", N2Oopt_4, { N2Oopt_2 } field = "" field = "READ THE MANUAL BEFORE USING NITROUS" dialog = N2OSystem1, "Nitrous System Stage 1" field = "Stage 1 Output - Nitrous", n2o1n_pins, { N2Oopt_2 } field = "Stage 1 Output - Fuel", n2o1f_pins, { N2Oopt_2 } field = "Enable Input On:", N2Oopt_pins, { N2Oopt_2 } field = "Additional Fuel PW @ N2O Min RPM", N2OPWLo, { N2Oopt_2 && !N2Oopt2_prog} field = "Additional Fuel PW @ N2O Max RPM", N2OPWHi, { N2Oopt_2 && !N2Oopt2_prog } field = "Retard Ignition By", N2OAngle, { N2Oopt_2 && !N2Oopt2_prog} field = "Nitrous Delay After Launch", N2Odel_launch, { N2Oopt_2 && launch_opt_on } field = "Nitrous Delay After Flat Shift", N2Odel_flat, { N2Oopt_2 && launch_opt_on } field = "" field = "" dialog = N2OSystem2, "Nitrous System Stage 2" field = "Nitrous stage 2", N2Oopt_3, { N2Oopt_2 } field = "Stage 2 Output - Nitrous", n2o2n_pins, { N2Oopt_2 && N2Oopt_3 } field = "Stage 2 Output - Fuel", n2o2f_pins, { N2Oopt_2 && N2Oopt_3 } field = "Enable Stage 2 Above", N2O2Rpm, { N2Oopt_2 && N2Oopt_3 && !N2Oopt2_prog } field = "Max RPM", N2O2RpmMax, { N2Oopt_2 && N2Oopt_3 && !N2Oopt2_prog } field = "Delay After Stage1", N2O2delay, { N2Oopt_2 && N2Oopt_3 && (!N2Oopt2_prog || !N2Oopt2_prog_time) } field = "Retard Ignition By", N2O2Angle, { N2Oopt_2 && N2Oopt_3 && !N2Oopt2_prog } field = "Additional Fuel PW @ N2O Min RPM", N2O2PWLo, { N2Oopt_2 && N2Oopt_3 && !N2Oopt2_prog } field = "Additional Fuel PW @ N2O Max RPM", N2O2PWHi, { N2Oopt_2 && N2Oopt_3 && !N2Oopt2_prog } dialog = N2OSystem_top, "", border panel = N2OSystem_topl, West panel = N2OSystem_topr, East dialog = N2OSystems, "", border panel = N2OSystem1, West panel = N2OSystem2, East dialog = nitrous, "Nitrous System", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#nitrous" panel = N2OSystem_top, North panel = N2OSystems, South dialog = n2o1_curves_time, "" panel = n2o1_duty_time panel = n2o1_pw_time panel = n2o1_retard_time dialog = n2o2_curves_time, "" panel = n2o2_duty_time panel = n2o2_pw_time panel = n2o2_retard_time dialog = nitrous_curves_time, "Nitrous - Time-Based Progressive", border panel = n2o1_curves_time, West panel = n2o2_curves_time, East dialog = n2o1_curves_rpm, "" panel = n2o1_duty_rpm panel = n2o1_pw_rpm panel = n2o1_retard_rpm dialog = n2o2_curves_rpm, "" panel = n2o2_duty_rpm panel = n2o2_pw_rpm panel = n2o2_retard_rpm dialog = nitrous_curves_rpm, "Nitrous - RPM-Based Progressive", border panel = n2o1_curves_rpm, West panel = n2o2_curves_rpm, East dialog = overboost, "Overboost Protection" field = "Overboost Protection", OverBoostOption field = "Maximum Boost", OverBoostKpa, { OverBoostOption > 0 } field = "Hysteresis", OverBoostHyst, { OverBoostOption > 0 } field = "Boost Tolerance", OverBoostOption_tol, { OverBoostOption && boost_ctl_settings_cl} field = "Tolerance", boosttol, {OverBoostOption && OverBoostOption_tol && boost_ctl_settings_cl} field = "Overboost Switching", tsw_pin_ob, { OverBoostOption > 0 } field = "Alt. Maximum Boost", OverBoostKpa2, { (tsw_pin_ob && (OverBoostOption > 0)) || dualfuel_sw2_ob } dialog = boostfeat, "" field = "Boost Table Switching", boost_feats_tsw, {boost_ctl_settings_on} field = "Boost Table Switching Gear", boost_gear_switch, { boost_feats_tsw == 15 } field = "Boost Timed From Launch", boost_feats_timed, {boost_ctl_settings_on && launch_opt_on} field = "Specific Launch Duty/Target", boost_feats_launch, {boost_ctl_settings_on && launch_opt_on} field = "Launch Boost Duty", boost_launch_duty, {boost_ctl_settings_on && launch_opt_on && boost_feats_launch && boost_ctl_settings_cl == 0} field = "Launch Boost Target", boost_launch_target, {boost_ctl_settings_on && launch_opt_on && boost_feats_launch && boost_ctl_settings_cl} field = "Boost vs Speed / Gear", boost_vss, {boost_ctl_settings_on} field = "Above TPS", boost_vss_tps, {boost_ctl_settings_on && boost_vss} field = "Per Gear Targets:" dialog = boostgeartargsl, "", yAxis field = "1", boost_geartarg1, {(boost_vss == 3) && gear_method && (gear_no > 0) && boost_ctl_settings_cl && boost_ctl_settings_on} field = "2", boost_geartarg2, {(boost_vss == 3) && gear_method && (gear_no > 1) && boost_ctl_settings_cl && boost_ctl_settings_on} field = "3", boost_geartarg3, {(boost_vss == 3) && gear_method && (gear_no > 2) && boost_ctl_settings_cl && boost_ctl_settings_on} dialog = boostgeartargsr, "", yAxis field = "4", boost_geartarg4, {(boost_vss == 3) && gear_method && (gear_no > 3) && boost_ctl_settings_cl && boost_ctl_settings_on} field = "5", boost_geartarg5, {(boost_vss == 3) && gear_method && (gear_no > 4) && boost_ctl_settings_cl && boost_ctl_settings_on} field = "6", boost_geartarg6, {(boost_vss == 3) && gear_method && (gear_no > 5) && boost_ctl_settings_cl && boost_ctl_settings_on} dialog = boostgeartargs, "", border panel = boostgeartargsl, West panel = boostgeartargsr, East dialog = boostctlSettings, "Boost Control Settings" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#boost" field = "Boost Control Enabled", boost_ctl_settings_on field = "Boost Control Use Initial Value Table", boost_ctl_settings_initialvals, { boost_ctl_settings_on && boost_ctl_settings_cl } field = "Solenoid Freq. Range", boost_ctl_pwm, {boost_ctl_settings_on} field = "Solenoid Frequency (Mid)", boost_ctl_pwm_scale, { boost_ctl_settings_on && (boost_ctl_pwm == 1)} field = "Boost Control Pin (Mid)", boost_ctl_pins_pwm, {boost_ctl_settings_on && (boost_ctl_pwm < 2)} field = "Solenoid Frequency (Slow)", boost_ctl_settings_freq, {boost_ctl_settings_on && (boost_ctl_pwm == 2)} field = "Boost Control Pin (Slow)", boost_ctl_pins, {boost_ctl_settings_on && (boost_ctl_pwm == 2)} field = "Output Polarity", boost_ctl_settings_invert_new, {boost_ctl_settings_on} field = "Control Interval", boost_ctl_ms, {boost_ctl_settings_on} field = "Minimum Duty", boost_ctl_closeduty, {boost_ctl_settings_on && boost_ctl_settings_cl} field = "Maximum Duty", boost_ctl_openduty, {boost_ctl_settings_on && boost_ctl_settings_cl} field = "Boost Control Lower CLT Threshold",boost_ctl_clt_threshold, {boost_ctl_settings_on} field = "Boost Control Lower Limit Delta", boost_ctl_lowerlimit, {boost_ctl_settings_on && boost_ctl_settings_cl } field = "Algorithm", boost_ctl_settings_cl, {boost_ctl_settings_on && boost_ctl_settings_on} field = "Tuning Mode", boost_ctl_settings_tunemode, {boost_ctl_settings_on && boost_ctl_settings_cl} slider = "Closed-Loop Sensitivity", boost_ctl_sensitivity, horizontal, {boost_ctl_settings_on && boost_ctl_settings_cl} field = "Proportional Gain", boost_ctl_Kp, {boost_ctl_settings_on && boost_ctl_settings_cl && boost_ctl_settings_tunemode} field = "Integral Gain", boost_ctl_Ki, {boost_ctl_settings_on && boost_ctl_settings_cl && boost_ctl_settings_tunemode} field = "Differential Gain", boost_ctl_Kd, {boost_ctl_settings_on && boost_ctl_settings_cl && boost_ctl_settings_tunemode} dialog = boosteast, "" panel = overboost, North panel = boostfeat, Center panel = boostgeartargs, South dialog = boost, "Boost Control Setings", border panel = boostctlSettings, West panel = boosteast, East dialog = boostctlSettings2, "Boost Control Settings 2" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#boost2" field = "Boost Control Enabled", boost_ctl_settings_on2, {boost_ctl_settings_on} field = "Target duty and boost tables 2 are used." field = "Boost vs VSS or time or tableswitch not supported." field = "Frequencies same as channel 1" field = "Boost Control Pin (Mid)", boost_ctl_pins_pwm2, {boost_ctl_settings_on && boost_ctl_settings_on2 && (boost_ctl_pwm < 2)} field = "Boost Control Pin (Slow)", boost_ctl_pins2, {boost_ctl_settings_on && boost_ctl_settings_on2 && (boost_ctl_pwm == 2)} field = "" field = "Minimum Duty", boost_ctl_closeduty2, {boost_ctl_settings_on && boost_ctl_settings_on2 && boost_ctl_settings_cl2} field = "Maximum Duty", boost_ctl_openduty2, {boost_ctl_settings_on && boost_ctl_settings_on2 && boost_ctl_settings_cl2} field = "Boost Control Lower Limit", boost_ctl_lowerlimit2, {boost_ctl_settings_on && boost_ctl_settings_cl2 } field = "" field = "Algorithm", boost_ctl_settings_cl2, {boost_ctl_settings_on && boost_ctl_settings_on2} slider = "Closed-Loop Sensitivity", boost_ctl_sensitivity2, horizontal, {boost_ctl_settings_on2 && boost_ctl_settings_cl2} field = "Tuning Mode", boost_ctl_settings_tunemode2, {boost_ctl_settings_on2 && boost_ctl_settings_cl2} field = "Proportional Gain", boost_ctl_Kp2, {boost_ctl_settings_on && boost_ctl_settings_on2 && boost_ctl_settings_cl2 && boost_ctl_settings_tunemode2} field = "Integral Gain", boost_ctl_Ki2, {boost_ctl_settings_on && boost_ctl_settings_on2 && boost_ctl_settings_cl2 && boost_ctl_settings_tunemode2} field = "Differential Gain", boost_ctl_Kd2, {boost_ctl_settings_on && boost_ctl_settings_on2 && boost_ctl_settings_cl2 && boost_ctl_settings_tunemode2} field = "MAP Sensor To Target", boost_ctl_sensor2, {boost_ctl_settings_on && boost_ctl_settings_on2 && boost_ctl_settings_cl2 && 0} field = "Must be defined in Generic Sensors" dialog = maxafrset, "" field = "Enable AFR Safety", maxafr_opt1_on field = "Warning Output", maxafr_opt1_led, { maxafr_opt1_on || egt_conf_action || fp_opt_safety || (water_pins_in_shut && water_freq_on) } field = "Load Axis", maxafr_opt1_load, { maxafr_opt1_on } field = "Check above Load", maxafr_en_load, { maxafr_opt1_on } field = "Check above RPM", maxafr_en_rpm, { maxafr_opt1_on } field = "Wait for", maxafr_en_time, { maxafr_opt1_on } field = "Kill spark For", maxafr_spkcut_time, { maxafr_opt1_on || egt_conf_action || fp_opt_safety || (water_pins_in_shut && water_freq_on) } field = "Then kill fuel until..." ;, "", { maxafr_opt1_on || egt_conf_action} field = "TPS Below", maxafr_ret_tps, { maxafr_opt1_on || egt_conf_action || fp_opt_safety || (water_pins_in_shut && water_freq_on) } field = "MAP Below", maxafr_ret_map, { maxafr_opt1_on || egt_conf_action || fp_opt_safety || (water_pins_in_shut && water_freq_on) } field = "RPM Below", maxafr_ret_rpm, { maxafr_opt1_on || egt_conf_action || fp_opt_safety || (water_pins_in_shut && water_freq_on) } dialog = maxafrTbls, "AFR Difference Table", border panel = maxafr1Tbl, West dialog = maxafr, "AFR Safety System", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#afrsafety" panel = maxafrset, West panel = maxafrTbls, East dialog = egtwestn, "Configuration" field = "No. EGT inputs", egt_num field = "" field = "Calibration - see documentation" field = "Temp At 0V", egtcal_temp0, {egt_num} field = "Temp At 5V", egtcal_tempmax, {egt_num} dialog = egtwests, "Actions" field = "EGT Actions", egt_conf_action field = "Warning LED same as AFR safety" field = "Warn Temperature", egt_warn, {egt_conf_action} field = "Added Fuel", egt_addfuel, {egt_conf_action} field = "Add To", egt_conf_bank, {egt_conf_action} field = "Shutdown Engine", egt_conf_shutdown, {egt_conf_action} field = "Time > Warn Temp", egt_time, {egt_conf_action && egt_conf_shutdown} field = "Max Temperature", egt_max, {egt_conf_action && egt_conf_shutdown} field = "See AFR safety for shutdown options" dialog = egtwest, "", yAxis panel = egtwestn, North panel = egtwests, South dialog = egteast, "Data capture" field = "EGT 1 Channel", egt1port, { (egt_num > 0) } field = "EGT 2 Channel", egt2port, { (egt_num > 1) } field = "EGT 3 Channel", egt3port, { (egt_num > 2) } field = "EGT 4 Channel", egt4port, { (egt_num > 3) } field = "EGT 5 Channel", egt5port, { (egt_num > 4) } field = "EGT 6 Channel", egt6port, { (egt_num > 5) } field = "EGT 7 Channel", egt7port, { (egt_num > 6) } field = "EGT 8 Channel", egt8port, { (egt_num > 7) } field = "EGT 9 Channel", egt9port, { (egt_num > 8) } field = "EGT 10 Channel", egt10port, { (egt_num > 9) } field = "EGT 11 Channel", egt11port, { (egt_num > 10) } field = "EGT 12 Channel", egt12port, { (egt_num > 11) } field = "EGT 13 Channel", egt13port, { (egt_num > 12) } field = "EGT 14 Channel", egt14port, { (egt_num > 13) } field = "EGT 15 Channel", egt15port, { (egt_num > 14) } field = "EGT 16 Channel", egt16port, { (egt_num > 15) } dialog = egt, "EGT / Thermocouple Inputs", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#egt" panel = egtwest, West panel = egteast, East dialog = injseq, "Sequenced Batch Fire" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#seqbatch" field = "These settings allow batch firing to be sequenced from a specific" field = "trigger number for repeatable phasing on each start." field = "Enable sequenced batch fire", feature3_3 field = "Injector Sequence Start Trigger No.", trig_init, {feature3_3 } dialog = canwest, "" field = "My CAN ID", mycan_id field = "Master Enable", can_enable_on field = "Enable PWM Polling", enable_pollPWM, {can_enable_on} field = "Remote CAN Id", can_poll_id, { enable_pollPWM && can_enable_on} field = "Remote Table Number For PWM Data", poll_tablePWM, { enable_pollPWM && can_enable_on} field = "Remote Table Offset For PWM Data", poll_offsetPWM, { enable_pollPWM && can_enable_on} field = "Remote Clock", canpwm_clk, { enable_pollPWM && can_enable_on} field = "Remote Prescale", canpwm_pre, { enable_pollPWM && can_enable_on} field = "Remote Divider", canpwm_div, { enable_pollPWM && can_enable_on} field = "" field = "Enable ADC Polling", enable_pollADC, {can_enable_on} dialog = caneast, "" field = "Digital ports" field = "Remote CAN Id", can_poll_id_ports, { enable_pollports_digin || enable_pollports_digout} field = "Table", poll_tableports, { enable_pollports_digin || enable_pollports_digout} field = "Enable Input Port", enable_pollports_digin field = "Offset", can_poll_digin_offset, { enable_pollports_digin} field = "Enable Output Port", enable_pollports_digout field = "Offset", can_poll_digout_offset, { enable_pollports_digout} field = "" field = "Enable PWM Outputs", enable_pwmout field = "Remote CAN Id", can_pwmout_id, { enable_pwmout } field = "Table", can_pwmout_tab, { enable_pwmout } field = "Offset", can_pwmout_offset, { enable_pwmout } field = "Force Duty To 0-255", enable_pwmout255 ;CAN adcs dialog = canadc_opt, "", yAxis field = "CAN ADC group on/off" field = "CAN ADC 1- 4", canadc_opt1, { enable_pollADC } field = "CAN ADC 5- 8", canadc_opt2, { enable_pollADC } field = "CAN ADC 9-12", canadc_opt3, { enable_pollADC } field = "CAN ADC 13-16", canadc_opt4, { enable_pollADC } field = "CAN ADC 17-20", canadc_opt5, { enable_pollADC } field = "CAN ADC 21-24", canadc_opt6, { enable_pollADC } dialog = canadc_id, "", yAxis field = "CAN Id" field = "", canadc_id1, { canadc_opt1 && enable_pollADC } field = "", canadc_id2, { canadc_opt2 && enable_pollADC } field = "", canadc_id3, { canadc_opt3 && enable_pollADC } field = "", canadc_id4, { canadc_opt4 && enable_pollADC } field = "", canadc_id5, { canadc_opt5 && enable_pollADC } field = "", canadc_id6, { canadc_opt6 && enable_pollADC } dialog = canadc_tab, "", yAxis field = "Table" field = "", canadc_tab1, { canadc_opt1 && enable_pollADC } field = "", canadc_tab2, { canadc_opt2 && enable_pollADC } field = "", canadc_tab3, { canadc_opt3 && enable_pollADC } field = "", canadc_tab4, { canadc_opt4 && enable_pollADC } field = "", canadc_tab5, { canadc_opt5 && enable_pollADC } field = "", canadc_tab6, { canadc_opt6 && enable_pollADC } dialog = canadc_off, "", yAxis field = "Offset" field = "", canadc_off1, { canadc_opt1 && enable_pollADC } field = "", canadc_off2, { canadc_opt2 && enable_pollADC } field = "", canadc_off3, { canadc_opt3 && enable_pollADC } field = "", canadc_off4, { canadc_opt4 && enable_pollADC } field = "", canadc_off5, { canadc_opt5 && enable_pollADC } field = "", canadc_off6, { canadc_opt6 && enable_pollADC } dialog = canadcs, "CAN ADC selection", xAxis panel = canadc_opt panel = canadc_id panel = canadc_tab panel = canadc_off dialog = can_top, "", xAxis panel = canwest, West panel = caneast, East, {can_enable_on} dialog = canparams, "CAN Parameters", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#canparams" panel = can_top, North panel = canadcs, South, {can_enable_on} dialog = canbroadcast, "CAN Broadcasting" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#canbroadcast" field = "Enable Broadcasting", can_bcast1_on field = "Broadcast Interval", can_bcast_int, { can_bcast1_on } field = "0x280 RPM * 4", can_bcast1_280x4, { can_bcast1_on } field = "0x280 RPM * 1", can_bcast1_280x1, { can_bcast1_on } field = "0x289 Coolant", can_bcast1_289, { can_bcast1_on } field = "0x316 RPM", can_bcast1_316, { can_bcast1_on } field = "0x329 Coolant", can_bcast1_329, { can_bcast1_on } field = "0x561 Alfa/Fiat/Lancia dash", can_bcast1_561, { can_bcast1_on } field = "0x361 Alfa/Fiat/Lancia", can_bcast1_361, { can_bcast1_on } field = "0x041 Alfa/Fiat/Lancia", can_bcast2_041, { can_bcast1_on } dialog = canvss1, "CAN VSS and gear selection" field = "This is for polling the actual vehicle speed" field = "mph/kph from a remote device." field = "For a pulse input use the CAN PWM instead" field = "Remote CAN Id", vss1_can_id field = "Remote CAN Table", vss1_can_table field = "" field = "VSS1 Offset", vss1_can_offset, {vss_opt1 == 0x0e} field = "Data Size", vss1_can_size, {vss_opt1 == 0x0e} field = "" field = "VSS2 Offset", vss2_can_offset, {vss_opt2 == 0x0e} field = "Data Size", vss2_can_size, {vss_opt2 == 0x0e} field = "" field = "Gear# Offset", gear_can_offset, {(gear_method & 0x03) == 0x03} dialog = canrtc, "Real Time Clock" field = "Enable Real Time Clock", opt142_rtc field = "Trim +/-", rtc_trim, {opt142_rtc} field = "Remote CAN Id", can_poll_id_rtc, {(opt142_rtc == 2) && can_enable_on} field = "Table", poll_table_rtc, {(opt142_rtc == 2) && can_enable_on } field = "Offset", poll_offset_rtc, {(opt142_rtc == 2) && can_enable_on} dialog = canego, "Innovate EGO Data Via CAN" field = "Fetch Innovate EGO data", can_poll2_ego field = "Remote CAN id", can_ego_id, {can_poll2_ego} field = "Table", can_ego_table, {can_poll2_ego} field = "Offset", can_ego_offset, {can_poll2_ego} dialog = cangps, "GPS Data Via CAN" field = "Fetch GPS Data", can_poll2_gps field = "Remote CAN Id", can_gps_id, {can_poll2_gps} field = "Table", can_gps_table, {can_poll2_gps} field = "Offset", can_gps_offset, {can_poll2_gps} dialog = canvss, "CAN VSS, Gear, EGO", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#canvss" panel = canvss1 panel = canego panel = cangps dialog = realtimeclock, "", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#rtc" panel = canrtc panel = std_ms3Rtc dialog = tablesw1, "Table Switching" field = "Fuel Table Switching", f5_0_tsf, { !(dualfuel_sw_on && dualfuel_sw_fuel) } field = "Switch Source", f5_0_tsf_opt, { f5_0_tsf && !(dualfuel_sw_on && dualfuel_sw_fuel)} field = "Input pin", tsw_pin_f, { f5_0_tsf && (f5_0_tsf_opt == 0) && !(dualfuel_sw_on && dualfuel_sw_fuel)} field = "RPM greater than", tsf_rpm, { f5_0_tsf && (f5_0_tsf_opt == 1) && !(dualfuel_sw_on && dualfuel_sw_fuel)} field = "MAP greater than", tsf_kpa, { f5_0_tsf && (f5_0_tsf_opt == 2) && !(dualfuel_sw_on && dualfuel_sw_fuel)} field = "TPS greater than", tsf_tps, { f5_0_tsf && (f5_0_tsf_opt == 3) && !(dualfuel_sw_on && dualfuel_sw_fuel)} field = "" field = "Spark Table Switching", f5_0_tss, { !(dualfuel_sw_on && dualfuel_sw_spk) } field = "Switch Source", f5_0_tss_opt, { f5_0_tss && !(dualfuel_sw_on && dualfuel_sw_spk)} field = "Input Pin", tsw_pin_s, { f5_0_tss && (f5_0_tss_opt == 0) } field = "RPM Greater Than", tss_rpm, { f5_0_tss && (f5_0_tss_opt == 1) && !(dualfuel_sw_on && dualfuel_sw_spk)} field = "MAP Greater Than", tss_kpa, { f5_0_tss && (f5_0_tss_opt == 2) && !(dualfuel_sw_on && dualfuel_sw_spk)} field = "TPS Greater Than", tss_tps, { f5_0_tss && (f5_0_tss_opt == 3) && !(dualfuel_sw_on && dualfuel_sw_spk)} field = "" field = "Req Fuel Switching", tsw_pin_rf, { !(dualfuel_sw_on && dualfuel_sw_rf)} field = "Alternate ReqFuel (Lower Number)", ReqFuel_alt, { tsw_pin_rf || (dualfuel_sw_on && dualfuel_sw_rf)} field = "" field = "AFR Table Switching", tsw_pin_afr, { !(dualfuel_sw_on && dualfuel_sw_afr)} field = "" field = "Stoich Switching", tsw_pin_stoich, { !(dualfuel_sw_on && dualfuel_sw_stoich)} field = "Alternate Stoich", stoich_alt, { tsw_pin_stoich || (dualfuel_sw_on && dualfuel_sw_stoich)} field = "" field = "Boost control table switching is on the boost control menu" dialog = dualfuel, "Dual Fuel switching" field = "Dual Fuel Enable", dualfuel_sw_on field = "Mode", dualfuel_opt_mode, { dualfuel_sw_on } field = "Outputs Mode", dualfuel_opt_out, { dualfuel_sw_on && !dualfuel_opt_mode } field = "Secondary Outputs", staged_extended_opts_use_v3, { dualfuel_sw_on && (dualfuel_opt_out || dualfuel_opt_mode) } ;was { ((dualfuel_opt_out || dualfuel_opt_mode) && hardware_fuel && ((nCylinders <= 4)) || ((nCylinders > 4) && (sequential == 1))) } field = "Secondary V3 Alternate", staged_extended_opts_simult, { ((dualfuel_opt_out || dualfuel_opt_mode) && staged_extended_opts_use_v3) || ((nCylinders > 4) && (dualfuel_opt_out || dualfuel_opt_mode) && hardware_fuel && !(sequential & 0x1)) } field = "Input Pin", dualfuel_pin, { dualfuel_sw_on && !dualfuel_opt_mode } field = "Alt. Fuel Tables", dualfuel_sw_fuel, { dualfuel_sw_on && !dualfuel_opt_mode } field = "Alt. Spark Tables", dualfuel_sw_spk, { dualfuel_sw_on && !dualfuel_opt_mode } field = "Alt. AFR Tables", dualfuel_sw_afr, { dualfuel_sw_on && !dualfuel_opt_mode } field = "Alt. ReqFuel", dualfuel_sw_rf, { dualfuel_sw_on && !dualfuel_opt_mode } field = "Alt. Stoich", dualfuel_sw_stoich, { dualfuel_sw_on && !dualfuel_opt_mode } field = "Alt. Warmup", dualfuel_sw_wue, { dualfuel_sw_on && !dualfuel_opt_mode } field = "Alt. AfterStart", dualfuel_sw_ase, { dualfuel_sw_on && !dualfuel_opt_mode } field = "Alt. Priming", dualfuel_sw2_prime, { dualfuel_sw_on && !dualfuel_opt_mode } field = "Alt. Cranking Pulse", dualfuel_sw2_crank, { dualfuel_sw_on && !dualfuel_opt_mode } field = "Alt. Injector Params", dualfuel_sw2_injp, { dualfuel_sw_on && !dualfuel_opt_mode } field = "Alt. Small Pulsewidths", dualfuel_sw2_smpw, { dualfuel_sw_on && !dualfuel_opt_mode } field = "Alt. Overboost", dualfuel_sw2_ob, { dualfuel_sw_on && !dualfuel_opt_mode } field = "Alt. Boost Table", dualfuel_sw2_boosw, { dualfuel_sw_on && !dualfuel_opt_mode } field = "" field = "Enable Temperature Adjustment", dualfuel_opt_temp, { dualfuel_sw_on && !dualfuel_opt_mode } field = "Temperature On", dualfuel_temp_sens, { dualfuel_sw_on && dualfuel_opt_temp} field = "Enable Pressure Adjustment", dualfuel_opt_press, { dualfuel_sw_on && !dualfuel_opt_mode } field = "Pressure In kPa On", dualfuel_press_sens, { dualfuel_sw_on && dualfuel_opt_press} field = "Sensor Type", dualfuel_press_type, { dualfuel_sw_on && dualfuel_opt_press && dualfuel_press_sens} dialog = tablesw, "Table Switch/Dual Fuel", xAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#tablesw" panel = tablesw1, West panel = dualfuel, East dialog = outputTestbuttons1a, "", xAxis ;commandButton = "Label Text", command, { Enabled Condition }, optionalFlags ; The rem > 0 expression is just for testing.. It works when the MS is on the Stim with rpm. ; a status bit there would be the expected real expression commandButton = "Enable Test Mode", cmdEnterTestMode, { (!(status3 & 8)) && (rpm == 0)} ; if clickOnCloseIfEnabled is set, then the command assigned to this button will be run on the ; dialog close, but only if the enable condition is true ; valid click flags are: ; clickOnCloseIfEnabled - the command will be sent on dialog close if active condition is true ; clickOnCloseIfDisabled - the command will be sent on dialog close if active condition is false ; clickOnClose - the command will be sent on dialog close always commandButton = "Disable Test Mode", cmdStopTestmode, { status3 & 8 }, clickOnCloseIfEnabled dialog = outputTestbuttons1b, "" field = "Ensure engine is stationary or stim RPM is 0 before testing injectors or coils" dialog = outputTestbuttons1, "Test Mode Controls", yAxis panel = outputTestbuttons1a panel = outputTestbuttons1b dialog = outputTestbuttons2, "Fuel pump", xAxis commandButton = "Fuel Pump On", cmdfpon, { status3 & 8 } commandButton = "Fuel Pump Off", cmdfpoff, { status3 & 8 } dialog = outputtest_spk_l, "", yAxis field = "Output Interval", testint displayOnlyField = "RPM (Coil-on-Plug)", testrpm field = "Coil Testing Mode", testop_coil field = "Coil Output To Test", testsel_coil field = "Dwell", testdwell dialog = outputtest_spk_r, "", yAxis commandButton = "Start", cmdtestspkon, { testop_coil && (status3 & 8) && testdwell } commandButton = "Stop", cmdtestinjspkoff, { status3 & 8 } dialog = outputtest_inj_l, "", yAxis field = "Output Interval", testint displayOnlyField = "RPM (Full Sequential)", testrpm field = "Injector Testing Mode", testop_inj field = "Injector Channel To Test", testsel_inj field = "Pulsewidth", testpw field = "Total Number Of Injections", testinjcnt field = "-" field = "Note: The following only applies to Inj1 and Inj2" field = "Injector PWM parameters", testop_pwm field = "PWM Current Limit", testinjPwmP, { testop_pwm } field = "PWM Time Threshold", testinjPwmT, { testop_pwm } field = "Injector PWM Period", testinjPwmPd , { testop_pwm } dialog = outputtest_inj_r, "", yAxis commandButton = "Start", cmdtestinjon, { testop_inj && (status3 & 8) && testpw && testinjcnt } commandButton = "Stop", cmdtestinjspkoff, { status3 & 8 } dialog = outputtest_spk, "Coil Testing", xAxis panel = outputtest_spk_l panel = outputtest_spk_r dialog = outputtest_inj, "Injector Testing", xAxis panel = outputtest_inj_l panel = outputtest_inj_r dialog = outputtest_controls, "Output Test Modes", yAxis panel = outputTestbuttons1 panel = outputTestbuttons2 panel = outputtest_spk panel = outputtest_inj dialog = outputtest_r, "Reference Gauges", yAxis gauge = voltMeter, North gauge = injcountGauge, South dialog = outputtest, "", xAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#testinjspk" panel = outputtest_controls panel = outputtest_r dialog = outputtest9, "Fuel Pump", yAxis commandButton = "Off", cmdfpoff, { status3 & 8 } commandButton = "On", cmdfpon, { status3 & 8 } ; "PM3 - Injection LED D14", "PM4 - Accel LED D16", "PM5 - Warmup LED D15", "PJ0 - IAC2", "PJ1 - IAC1", "PJ7 - JS11", "PP2 - Idle", "PP3 - Boost", "PP4 - Nitrous 1", "PP5 - Nitrous 2", "PP6 - VVT", "PP7 - Fidle", "PT1 - V3 Inj 1", "PT3 - V3 Inj 2", "PT5 - JS10", "PK0 - Tacho", "PA0 - Inj A", "PA1 - Inj B", "PA2 - Inj C", "PA3 - Inj D", "PA4 - Inj E", "PA5 - Inj F", "PA6 - Inj G", "PA7 - Inj H", dialog = outputtest16, "PP2-Idle", yAxis commandButton = "Off", cmdtest16off, { status3 & 8 } commandButton = "Pulsed", cmdtest16pulsed, { status3 & 8 } commandButton = "On", cmdtest16on, { status3 & 8 } dialog = outputtest10, "PP3-Boost", yAxis commandButton = "Off", cmdtest10off, { status3 & 8 } commandButton = "Pulsed", cmdtest10pulsed, { status3 & 8 } commandButton = "On", cmdtest10on, { status3 & 8 } dialog = outputtest11, "PP4-Nitrous1", yAxis commandButton = "Off", cmdtest11off, { status3 & 8 } commandButton = "Pulsed", cmdtest11pulsed, { status3 & 8 } commandButton = "On", cmdtest11on, { status3 & 8 } dialog = outputtest12, "PP5-Nitrous2", yAxis commandButton = "Off", cmdtest12off, { status3 & 8 } commandButton = "Pulsed", cmdtest12pulsed, { status3 & 8 } commandButton = "On", cmdtest12on, { status3 & 8 } dialog = outputtest13, "PP6-VVT", yAxis commandButton = "Off", cmdtest13off, { status3 & 8 } commandButton = "Pulsed", cmdtest13pulsed, { status3 & 8 } commandButton = "On", cmdtest13on, { status3 & 8 } dialog = outputtest14, "PP7-Fidle", yAxis commandButton = "Off", cmdtest14off, { status3 & 8 } commandButton = "Pulsed", cmdtest14pulsed, { status3 & 8 } commandButton = "On", cmdtest14on, { status3 & 8 } dialog = outputtest15, "PK0-Tacho", yAxis commandButton = "Off", cmdtest15off, { status3 & 8 } commandButton = "Pulsed", cmdtest15pulsed, { status3 & 8 } commandButton = "On", cmdtest15on, { status3 & 8 } dialog = outputtest_io_warning, "" field = "Caution! Used incorrectly this can cause hardware damage. USE AT YOUR OWN RISK." field = "The pin/port will be forced into an output overriding any other configuration." field = "After testing, turn off/on the ECU to restore normal settings." dialog = outputtest_io_pwm, "Pulse Settings", xAxis field = "Pulse Frequency", pwm_testio field = "Pulse Duty Cycle", duty_testio dialog = outputtest_io1, "Outputs", xAxis panel = outputtest9 panel = outputtest16 panel = outputtest10 panel = outputtest11 panel = outputtest12 panel = outputtest13 panel = outputtest14 panel = outputtest15 dialog = outputtest_io, "", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#testio" panel = outputTestbuttons1 panel = outputtest_io_pwm panel = outputtest_io1 panel = outputtest_io_warning dialog = iactest_l, "", yAxis field = "Idle valve testing can be used with the engine running or stationary" field = "" field = "Idle Valve Homing Steps", iachometest, { IdleCtl == 3 } field = "Idle Valve Step (0-255)", iacpostest, { IdleCtl == 3 } field = "PWM Idle Duty% (0-100)", iacpostest, { IdleCtl == 2 } field = "Set the steps before enabling testing" dialog = iactest_r, "", yAxis commandButton = "Enable Test - Home Position", cmdtestiachome, {( IdleCtl == 3 ) } commandButton = "Enable Test - Run Position", cmdtestiacon commandButton = "Enable Test - In/Out Cycle", cmdtestiaccycle, { IdleCtl == 3 } commandButton = "Stop Testing", cmdtestiacoff, {1}, clickOnCloseIfEnabled dialog = iactest_top, "", xAxis panel = iactest_l panel = iactest_r dialog = iactest_bot, "", xAxis gauge = IACgauge gauge = PWMIdlegauge dialog = iactest, "Output Test Mode - Idle Valve", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#testidle" panel = iactest_top panel = iactest_bot dialog = injseqtest, "Injector Sequential Testing" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#injseqtest" commandButton = "Stop Testing", cmdtestinjnorm commandButton = "Batch Fire", cmdtestinjbat commandButton = "Semi Sequential", cmdtestinjsem commandButton = "Full Sequential", cmdtestinjseq dialog = special, "Special Options" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#special" field = "Pulsewidth Scaling", feature3_pw4x field = "Nitrous-In Pulldown", feature3_n2oin ; field = "U08 Debug 134, SPI baud", u08_debug134 ; field = "U16 Debug 640", u16_debug640 ; field = "SDcard Run/Test", u08_debug38_0 field = "Log trigger times to sensors9-16", u08_debug38_1 field = "Fuel flow/consumption calculation interval", fuelcalctime field = "Maximum SpkAdj Value", spkadj_max field = "Minimum SpkAdj Value", spkadj_min dialog = lttrim, "Long Term Trim Settings" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#lttrim" field = "Enable Experi. Long Term Trim", ltt_opt_on field = "Sample Interval", ltt_samp_time, {ltt_opt_on} field = "Correction Softness", ltt_agg, {ltt_opt_on} field = "Write Method", ltt_opt_mode, {ltt_opt_on} field = "Burn Button", ltt_but_in, {ltt_opt_on && (ltt_opt_mode == 1)} field = "Burn Interval", ltt_int, {ltt_opt_on && (ltt_opt_mode == 0)} field = "LED Output", ltt_led_out,{ltt_opt_on} field = "Total Change Before Burning", ltt_thresh, {ltt_opt_on} field = "Display Current %Change In Sensor15", ltt_opt_feedback, {ltt_opt_on} commandButton = "Read Table 1 To RAM", cmdlttr1 commandButton = "Read Table 2 To RAM", cmdlttr2 commandButton = "Burn Table To Flash", cmdlttw commandButton = "Zero Tables", cmdlttz dialog = EAElagcomp, "EAE Lag Compensation" field = "Source", EAElagsource field = "Threshold", EAElagthresh field = "Max RPM", EAElagRPMmax dialog = RotaryTrailingSettings, "Rotary Settings" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#rotary" field = "See also Rotary Split Table" field = "Output Mode", RotarySplitModeFD, { (twoStroke == 3) && (nCylinders == 2) && (spk_mode3 == 2) } field = "Allow Negative Split?", RotarySplitModeNeg, { twoStroke == 3 } field = "Trailing Dwell Time", dwelltime_trl, { (twoStroke == 3) && (spk_mode0 >1) && (dwellmode==0) } dialog = noisefiltering, "", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#noise" field = "#GLOBAL TIMER NOISE FILTER DELAY" field = "Noise Filter Period", dlyct field = "#PRIMARY TACH (crank)" field = "Noise Filter Enabled", NoiseFilterOpts field = "Use noise filter curve to tune" field = "Tach Period Rejection", NoiseFilterOpts1 field = "Tach Interrupt Masking", NoiseFilterOpts2, {NoiseFilterOpts == 0} field = "Time", ICISR_tmask, {NoiseFilterOpts1 || NoiseFilterOpts2} field = "Percentage", ICISR_pmask, {NoiseFilterOpts1 || NoiseFilterOpts2} field = "#SECONDARY TACH (cam)" field = "Noise Filter Enabled", secondtrigopts; field = "Noise Filter Time Period", TC5_required_width, { secondtrigopts & 0x1 } field = "Tach Period Rejection", secondtrigopts1 field = "Tach Interrupt Masking", secondtrigopts2, { secondtrigopts == 0 } field = "Time", IC2ISR_tmask, {secondtrigopts1 || secondtrigopts2} field = "Percentage", IC2ISR_pmask, {secondtrigopts1 || secondtrigopts2} dialog = noisefilterpad field = "" field = "" field = "" field = "" dialog = Eastnoisefilter, "", yAxis panel = NoiseFiltercurve panel = noisefilterpad, South dialog = noisefiltering2, "Noise Filtering", xAxis panel = noisefiltering, West panel = Eastnoisefilter, East dialog = launchwest, "" field = "Launch Control Option:", launch_opt_on field = "LAUNCH" field = "Input On:", launch_opt_pins, { launch_opt_on } field = "Launch Hard Limit", launch_hrd_lim, {launch_opt_on} field = "Soft Limit Zone", launch_sft_zone, {launch_opt_on} field = "Soft Limit Retard To", launch_sft_deg, {launch_opt_on } field = "Launch Fuel Add/Remove", launch_opt_bank, { launch_opt_on } field = "Fuel Addition", launch_addfuel, {launch_opt_bank && launch_opt_on} field = "Enable Launch When TPS Above ", launch_tps, { launch_opt_on >0} field = "Limiter Method", launchlimopt, { launch_opt_on >0} field = "Disable Launch When VSS1 Above", launch_maxvss, { (launch_opt_on ) && (vss_opt0_1) } field = "FLAT SHIFT" field = "Disable Flat-Shift When VSS1 Below", flats_minvss, { (launch_opt_on > 1) && (vss_opt0_1) } field = "Flat Shift Arming RPM", flats_arm, { launch_opt_on >1 } field = "Flat Shift Hard Rev Limit", flats_hrd, { launch_opt_on >1 } field = "Soft Limit Retard To : ", flats_deg, { launch_opt_on >1 } field = "Cut Fuel Above", launch_fcut_rpm, { (launchlimopt & 1) && (launch_opt_on >0) } field = "TIMED RETARD" field = "Timed Retard After Launch", launch_opt_retard, { launch_opt_on } dialog = launchnortheast, "Variable Launch" field = "Variable Launch Input", launch_var_on, { launch_opt_on >0 } field = " -Minimum Setting", launch_var_low, {launch_var_on && launch_opt_on >0 } field = " -Maximum Setting", launch_var_up, {launch_var_on && launch_opt_on >0 } dialog = launchsoutheast, "3-Step / Burnout Limiter" field = "3-step Input", launch_3step_in, {launch_opt_on >0 } field = " -Soft Limit Retard To", launch_sft_deg3, {launch_3step_in && launch_opt_on >0} field = " -Hard Limit", launch_hrd_lim3, {launch_3step_in && launch_opt_on >0} dialog = launchtbtstop, "Transbrake, Throttle Stop" field = "Transbrake Button Input", timedout1_in field = "Transbrake Output", timedout1_out, {timedout1_in} field = "Delay", timedout1_offdelay, {timedout1_in && timedout1_out} field = "Turbo Staging Button", tcs_in, {timedout1_in} field = "Release Time", tcs_offtime, {tcs_in && timedout1_in} field = "On Time", tcs_ontime, {tcs_in && timedout1_in} field = "Main # Moves", tcs_moves, {tcs_in && timedout1_in} field = "Throttle Stop Output", tstop_out, { launch_opt_on } field = "On Delay After Launch", tstop_delay, {tstop_out && launch_opt_on} field = "Keep On For", tstop_hold, {tstop_out && launch_opt_on} dialog = launcheast, "", yAxis panel = launchnortheast panel = launchtbtstop panel = launchsoutheast dialog = launch, "Launch Control/ 2-Step / 3-Step / T-brake", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#launch" panel = launchwest, West panel = launcheast, East dialog = vsslaunch1, "" field = "Wheel-Speed Based Launch", launch_opt_vss field = "ACTIVATION" field = "Enable Launch When TPS Above ", launch_tps, { launch_opt_vss} field = "Timeout (0 = None)", launchvsstime, { launch_opt_vss} field = "Re-arm Below Speed", launchvss_minvss, { launch_opt_vss} field = "Enable Gear Checking", launch_opt_vssgear, { launch_opt_vss && gear_method } field = "Maximum Gear", launchvss_maxgear, { launch_opt_vss && launch_opt_vssgear && gear_method} field = "LIMITER" field = "Limiter Method", launchlimopt, { launch_opt_vss} field = "Hard limit is taken from the curve" field = "Soft Limit Zone", launch_sft_zone, { launch_opt_vss } field = "Retard To", launch_sft_deg, {launch_opt_vss } field = "Launch Fuel Add/Remove", launch_opt_bank, { launch_opt_vss } field = "Fuel Addition", launch_addfuel, {launch_opt_bank && launch_opt_vss} field = "Limiter settings are shared with the launch control page." dialog = vsslaunch, "Speed-Based Launch Control", border panel = vsslaunch1, West panel = vsslaunch_curve, East dialog = tacho, "Tacho Output" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#tachoout" field = "Tacho Output Enabled", tacho_opt80 field = "" field = "Output On:", tacho_opt3f, { tacho_opt80 } field = "Speed", tacho_opt40, { tacho_opt80 } dialog = overrun, "Over-Run Fuel Cut" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#overrun" field = "Over-Run Fuel Cut", OvrRunC field = "Cut fuel when:" field = "RPM Greater Than:", fc_rpm, { OvrRunC } field = "And MAP Lower Than: ", fc_kpa, { OvrRunC } field = "And TPS Lower Than: ", fc_tps, { OvrRunC } field = "And CLT Greater Than:", fc_clt, { OvrRunC } field = "After Delay", fc_delay, { OvrRunC } field = "Progressive Fuel Cut", OvrRunC_progcut, { OvrRunC } field = "Ignition Timing Transition (Cut)", OvrRunC_progign, {OvrRunC} field = "Ignition Timing During Over-Run", fc_timing, { OvrRunC && (OvrRunC_progign || OvrRunC_retign)} field = "Cut Transition Time", fc_transition_time, { OvrRunC && (OvrRunC_progcut || OvrRunC_progign)} field = "Progressive Fuel Return", OvrRunC_progret, { OvrRunC } field = "Ignition Timing Transition Return", OvrRunC_retign, { OvrRunC } field = "Return Transition Time", fc_trans_time_ret, { OvrRunC && (OvrRunC_progret || OvrRunC_retign) } field = "Lowest RPM To Re-Engage Fuel:", fc_rpm_lower, { OvrRunC } field = "RPMdot For Upper RPM Re-Engagement", fuelcut_fuelon_upper_rpmdot, { OvrRunC } field = "RPMdot For Lower RPM Re-Engagement", fuelcut_fuelon_lower_rpmdot, { OvrRunC } field = "Duration Of Fuel Adder", fc_ae_time, { OvrRunC } field = "Size Of Fuel Adder", fc_ae_pct, { OvrRunC && fc_ae_time } field = "Delay EGO After Fuel Return:", fc_ego_delay, { OvrRunC } dialog = staging, "Staged Injection" field = "Staged Injection First Parameter", staged_first_param field = "Primary Injector Size", staged_pri_size, { staged_first_param } field = "Secondary Injector Size", staged_sec_size, { staged_first_param } field = "Transition Fully To Secondaries", staged_extended_opts_pw1off, { staged_first_param } field = "Secondary Outputs", staged_extended_opts_use_v3, { staged_first_param && (staged_out1 == 0) } field = "Secondary V3 Alternate", staged_extended_opts_simult, { ((staged_extended_opts_use_v3 && staged_first_param) || ((nCylinders > 4) && (staged_first_param) && (hardware_fuel) && !(sequential & 0x1))) && (staged_out1 == 0) } field = "" field = "Gradual Transition", staged_transition_on, { staged_first_param && ((staged_first_param & 0x7) != 5) } field = "Transition Events", staged_transition_events, { (staged_first_param && staged_transition_on) && ((staged_first_param & 0x7) != 5) } field = "Primary Reduction Delay", staged_primary_delay, { (staged_first_param && staged_transition_on) && ((staged_first_param & 0x7) != 5) && (staged_out1 == 0) } field = "Secondary Enrichment", staged_secondary_enrichment, { (staged_first_param && staged_transition_on) && ((staged_first_param & 0x7) != 5) && (staged_out1 == 0) } field = "" field = "Primary Staging Threshold", staged_param_1, { staged_first_param && ((staged_first_param & 0x7) != 5) } field = "Primary Staging Hysteresis", staged_hyst_1, { staged_first_param && ((staged_first_param & 0x7) != 5) } field = "" field = "Second Parameter", staged_second_param, { staged_first_param && ((staged_first_param & 0x7) != 5) } field = "Secondary Staging Threshold", staged_param_2, { staged_second_param } field = "Secondary Staging Hysteresis", staged_hyst_2, { staged_second_param } field = "Secondary Staging Logic", staged_second_logic, { staged_second_param } field = "" field = "Relay Output", staged_out1, { staged_first_param } field = "Relay Output Polarity", staged_out1_inv, { staged_first_param && staged_out1} field = "Pre-Relay Output", staged_out2, { staged_first_param } field = "Pre-Relay Output Polarity", staged_out2_inv, { staged_first_param && staged_out2} field = "Pre-Relay Timer", staged_out2_time, { staged_first_param && staged_out2} dialog = stagedCombined, "Staged Injection", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#stagedinj" panel = staging, West panel = stagedTable, Center, { (staged_first_param & 0x7) == 5 } dialog = crsettings, "Cranking / Startup Settings" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#crankstart" field = "Cranking RPM", crankingRPM field = "" field = "Flood Clear TPS", floodClear field = "Above this throttle no fuel is injected" field = "Batch Fire During Crank", feature7_batchcrank, {sequential} field = "Cranking Taper Curve", feature7_cranktaper field = "Cranking Taper Curve Units", feature7_crtpunits, {feature7_cranktaper} field = "Cranking Fuel Pulse Rate ", altcrank field = "Blended Cranking Curves", alternate_blend field = "" field = "Priming Pulse Delay", primedelay field = "Ignore MAT Correction During ASE", feature3_matase field = "ASE Count Units", feature3_aseunit dialog = generalSettings, "Baro Sensor Settings" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#barocor" field = "Barometric Correction", baroCorr field = "Realtime Baro Port", rtbaroport, {baroCorr == 2} field = "Upper Limit", baro_upper, {baroCorr} field = "Lower Limit", baro_lower, {baroCorr} field = "Default Baro", baro_default, {baroCorr < 2} dialog = gsmap, "MAP Sensor Settings" field = "MAP Sensor Type", mapport_t field = "Voltage Input Port", mapport, {mapport_t == 0} field = "Frequency Input Port", mapport_f, {mapport_t == 1} field = "Low Frequency", map_freq0, {mapport_t == 1} field = "High Frequency", map_freq1, {mapport_t == 1} field = "2nd MAP Port", map2port, { (mapport_t == 0) } field = "(See also Tools->Calibrate MAP/Baro)" dialog = gsgen, "General Sensor Settings" field = "MegaView Temp. Units", tempUnits field = "MAP Averaging Lag Factor", mapLF field = "MAF Averaging Lag Factor", mafLF field = "RPM Averaging Lag Factor", rpmLF field = "TPS Averaging Lag Factor", tpsLF field = "Lambda Averaging Lag Factor", egoLF field = "CLT/MAT/Battery/Baro Lag Factor", adcLF field = "Auto-zero TPS", feature3_tps dialog = secondaryLoad, "Load Parameters" field = "Primary Fuel Load", algorithm field = "Secondary Fuel Load", algorithm2 field = "Secondary Fuel", loadCombine, {algorithm2 != 0 } field = "Multiply MAP (VE1/3)", loadMult field = "99% of Speed-Density installs should use Multiply" field = "Multiply MAP (VE2/4)", loadMult2, {algorithm2 && (loadCombine == 2)} field = "Incorporate AFRTarget", loadStoich field = "Stoichiometric AFR", stoich ;, { loadStoich } needed for lambda calc even if not incl AFR field = "Primary Ignition Load", IgnAlgorithm field = "Secondary Ignition Load", IgnAlgorithm2 field = "Secondary Ignition", loadCombineign, {IgnAlgorithm2} field = "AFR table Load", afrload field = "EAE curve Load", eaeload dialog = overrun_note field = "Overrun is on the fuel menu" dialog = eastgeneral, "" panel = secondaryLoad, North panel = overrun_note, South dialog = generalsettings3, "", border panel = generalSettings, North panel = gsmap, Center panel = gsgen, South dialog = generalsettings2, "General Settings", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#genset" panel = generalsettings3, West panel = eastgeneral, East dialog = revlimiter, "" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#revlim" field = "HARD REV LIMIT" field = "Hard Rev Limit", RevLimNormal2 field = "Soft Limit Zone / Hysteresis", RevLimNormal2_hyst field = "COOLANT TEMP LIMITER" field = "Rev Limiter CLT Based", RevLimCLTbased field = "Rev Limit TPS Bypass", TpsBypassCLTRevlim, { RevLimCLTbased & 1 } field = "RPM When In TPS Bypass", RevLimTPSbypassRPM, { RevLimCLTbased & 1 } field = "SPARK RETARD" field = "Spark Retard Mode", RevLimOption_retard field = "Maximum Retard", RevLimMaxRtd, { RevLimOption_retard == 1 } field = "Retard To", RevLimRtdAng, { RevLimOption_retard == 2} field = "SPARK CUT" field = "Enable Spark Cut Limiting", RevLimOption_spkcut field = "FUEL CUT" field = "Enable Fuel Cut Limiting", RevLimOption_fuelcut field = "Progressive Fuel Cut", RevLimOption_fuelprog, {RevLimOption_fuelcut} field = "" field = "" field = "" field = "" dialog = revlimiter2, "Rev Limiter", border panel = revlimiter, West panel = revlimiterBins, Center, { RevLimCLTbased & 1 } dialog = flexn, "" field = "#Spark/Fuel" field = "Sensor Frequency" field = "Ethanol Mix" field = "Fuel Multiplier%" field = "Timing Addition" field = "#Temp Sense" field = "Sensor PW" field = "Fuel Temp" dialog = flexl, "" field = "Low" field = "", fuelFreq0, { flexFuel } field = "", flex_pct0, { flexFuel } field = "", fuelCorr0, { flexFuel } field = "", fuelSpkDel0, { flexFuel } field = "Low" field = "", ff_tpw0, { flexFuel && (fueltemp1 == 1)} field = "", ff_temp0, { flexFuel && (fueltemp1 == 1)} dialog = flexh, "" field = "High" field = "", fuelFreq1, { flexFuel } field = "", flex_pct1, { flexFuel } field = "", fuelCorr1, { flexFuel } field = "", fuelSpkDel1, { flexFuel } field = "High" field = "", ff_tpw1, { flexFuel && (fueltemp1 == 1)} field = "", ff_temp1, { flexFuel && (fueltemp1 == 1)} dialog = ff_table1, "", xAxis panel = flexn panel = flexl panel = flexh dialog = ff_fallback, "", yAxis field = "Baseline Ethanol%", flex_baseline, { flexFuel } field = "#Fallback For Sensor Failure" field = "Fallback Fuel Multiplier%", fuelCorr_default, { flexFuel > 0 } field = "Fallback Timing Addition", fuelSpkDel_default, { flexFuel > 0 } dialog = flexFuelSettings, "Fuel Sensor Settings", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#flex" field = "Flex Fuel Sensor", flexFuel field = "Sensor Port", flexport, { flexFuel > 0 } panel = ff_table1 field = "Temperature Input", fueltemp1 panel = ff_fallback dialog = sequentialOptions, "Sequential Fuel Injection" field = "Main Fuel Outputs", hardware_fuel field = "Sequential On", sequential field = "Angle Specifies:", sequential_angle_spec, { sequential != 0 } field = "Injector Trim", sequential_trim_on_off #if CYL_12_16_SUPPORT field = "Injector I/J Outputs", hardware_injij, { nCylinders > 8} #endif dialog = firingorder1, "Firing Order" field = "A.", firea field = "B.", fireb, { nCylinders > 1} field = "C.", firec, { nCylinders > 2} field = "D.", fired, { nCylinders > 3} field = "E.", firee, { nCylinders > 4} field = "F.", firef, { nCylinders > 5} field = "G.", fireg, { nCylinders > 6} field = "H.", fireh, { nCylinders > 7} #if CYL_12_16_SUPPORT dialog = firingorder2, "Firing Order" field = "I.", firei, { nCylinders > 8} field = "J.", firej, { nCylinders > 9} field = "K.", firek, { nCylinders > 10} field = "L.", firel, { nCylinders > 11} field = "M.", firem, { nCylinders > 12} field = "N.", firen, { nCylinders > 13} field = "O.", fireo, { nCylinders > 14} field = "P.", firep, { nCylinders > 15} #endif field = "" dialog = firingorder, "", xAxis panel = firingorder1, West #if CYL_12_16_SUPPORT panel = firingorder2, East #endif dialog = seqfo, "", border panel = sequentialOptions, North panel = firingorder, South dialog = base3, "", yAxis field = "Engine Size", enginesize field = "Injector Size Each", staged_pri_size dialog = base2, "", yAxis panel = std_injection, North panel = base3, South dialog = base, "Engine and Sequential Settings", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#engseq" panel = base2, West panel = seqfo, East ;main injector parameters dialog = ot_ot, "", yAxis field = "Inj Parameters" field = "Dead-Time" field = "@ 13.2V" field = "A", injOpen1 field = "B", injOpen2, {opentime_opt1_master} field = "C", injOpen3, {opentime_opt1_master} field = "D", injOpen4, {opentime_opt1_master} field = "E", injOpen5, {opentime_opt1_master} field = "F", injOpen6, {opentime_opt1_master} field = "G", injOpen7, {opentime_opt1_master} field = "H", injOpen8, {opentime_opt1_master} dialog = ot_curve, "", yAxis field = "", opentime_opt1_master field = "Voltage Dead" field = "Time Curve" field = "", opentime_opt1 field = "", opentime_opt2, {opentime_opt1_master} field = "", opentime_opt3, {opentime_opt1_master} field = "", opentime_opt4, {opentime_opt1_master} field = "", opentime_opt5, {opentime_opt1_master} field = "", opentime_opt6, {opentime_opt1_master} field = "", opentime_opt7, {opentime_opt1_master} field = "", opentime_opt8, {opentime_opt1_master} dialog = injchar_ms3x, "MS3X Injectors", xAxis panel = ot_ot panel = ot_curve dialog = injchar_v3, "Mainboard Injectors", yAxis field = "BANK 1 Dead-Time @ 13.2V", injOpena field = "Correction Curve", opentime_opta field = "PWM Current Limiting", opentime_opta_pwm field = "PWM Current Limit", injPwmP, {opentime_opta_pwm} field = "PWM Time Threshold", injPwmT, {opentime_opta_pwm} field = "Injector PWM Period", injPwmPd, {opentime_opta_pwm} field = "" field = "BANK 2 Different Settings", opentime_optb_own field = "Dead Time", injOpenb, {opentime_optb_own} field = "Correction Curve", opentime_optb, {opentime_optb_own} field = "PWM Current Limiting", opentime_optb_pwm, {opentime_optb_own} field = "PWM Current Limit", injPwmP2, {opentime_optb_own && opentime_optb_pwm} field = "PWM Time Threshold", injPwmT2, {opentime_optb_own && opentime_optb_pwm} field = "Injector PWM Period", injPwmPd2, {opentime_optb_own && opentime_optb_pwm} ; 9-16 dialog = ot_otb, "", yAxis field = "Dead-Time" field = "@ 13.2V" field = "I", injOpena, {opentime_opt1_master} field = "J", injOpenb, {opentime_opt1_master} field = "K", injOpen11, {opentime_opt1_master} field = "L", injOpen12, {opentime_opt1_master} field = "M", injOpen13, {opentime_opt1_master} field = "N", injOpen14, {opentime_opt1_master} field = "O", injOpen15, {opentime_opt1_master} field = "P", injOpen16, {opentime_opt1_master} dialog = ot_curveb, "", yAxis field = "Voltage Cead" field = "Time Curve" field = "", opentime_opta, {opentime_opt1_master} field = "", opentime_optb, {opentime_opt1_master} field = "", opentime_opt11, {opentime_opt1_master} field = "", opentime_opt12, {opentime_opt1_master} field = "", opentime_opt13, {opentime_opt1_master} field = "", opentime_opt14, {opentime_opt1_master} field = "", opentime_opt15, {opentime_opt1_master} field = "", opentime_opt16, {opentime_opt1_master} dialog = injcurveswest, "", yAxis panel = opencurve0, North panel = opencurve2, South dialog = injcurveseast, "", yAxis panel = opencurve1, North panel = opencurve3, South dialog = injcurves, "", xAxis panel = injcurveswest panel = injcurveseast dialog = injsettingsb, "Injector Dead-Time/PWM (9-16)", xAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#injdt" panel = ot_otb panel = ot_curveb dialog = injCharswest, "", yAxis panel = injchar_ms3x, North panel = injchar_v3, South dialog = injsettings, "", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#injdt" panel = injCharswest, West panel = injcurves, Center ; table-switched alternate parameters dialog = ot_ot2b, "", yAxis field = "Dead-Time" field = "@ 13.2V" field = "I", inj2Opena, {opentime2_opt1_master} field = "J", inj2Openb, {opentime2_opt1_master} field = "K", inj2Open11, {opentime2_opt1_master} field = "L", inj2Open12, {opentime2_opt1_master} field = "M", inj2Open13, {opentime2_opt1_master} field = "N", inj2Open14, {opentime2_opt1_master} field = "O", inj2Open15, {opentime2_opt1_master} field = "P", inj2Open16, {opentime2_opt1_master} dialog = ot_curve2b, "", yAxis field = "Voltage Dead" field = "Time curve" field = "", opentime2_opta, {opentime2_opt1_master} field = "", opentime2_optb, {opentime2_opt1_master} field = "", opentime2_opt11, {opentime2_opt1_master} field = "", opentime2_opt12, {opentime2_opt1_master} field = "", opentime2_opt13, {opentime2_opt1_master} field = "", opentime2_opt14, {opentime2_opt1_master} field = "", opentime2_opt15, {opentime2_opt1_master} field = "", opentime2_opt16, {opentime2_opt1_master} dialog = injsettingsb2, "Injector Dead-Time/PWM 2 (9-16)", xAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#injdt2" panel = ot_ot2b panel = ot_curve2b dialog = ot_ot2, "", yAxis field = "Inj Parameters" field = "Dead-Time" field = "@ 13.2V" field = "A", inj2Open1 field = "B", inj2Open2, {opentime2_opt1_master} field = "C", inj2Open3, {opentime2_opt1_master} field = "D", inj2Open4, {opentime2_opt1_master} field = "E", inj2Open5, {opentime2_opt1_master} field = "F", inj2Open6, {opentime2_opt1_master} field = "G", inj2Open7, {opentime2_opt1_master} field = "H", inj2Open8, {opentime2_opt1_master} dialog = ot_curve2, "", yAxis field = "", opentime2_opt1_master field = "Voltage Dead" field = "Time Curve" field = "", opentime2_opt1 field = "", opentime2_opt2, {opentime2_opt1_master} field = "", opentime2_opt3, {opentime2_opt1_master} field = "", opentime2_opt4, {opentime2_opt1_master} field = "", opentime2_opt5, {opentime2_opt1_master} field = "", opentime2_opt6, {opentime2_opt1_master} field = "", opentime2_opt7, {opentime2_opt1_master} field = "", opentime2_opt8, {opentime2_opt1_master} dialog = injchar_ms3x_2, "MS3X Injectors", xAxis panel = ot_ot2 panel = ot_curve2 dialog = injchar_v3_2, "Mainboard Injectors", yAxis field = "BANK 1 Dead-Time @ 13.2V", inj2Opena field = "Correction Curve", opentime2_opta field = "PWM Current Limiting", opentime2_opta_pwm field = "PWM Current Limit", inj2PwmP, {opentime2_opta_pwm} field = "PWM Time Threshold", inj2PwmT, {opentime2_opta_pwm} field = "Injector PWM Period", inj2PwmPd, {opentime2_opta_pwm} field = "" field = "BANK 2 Different Settings", opentime2_optb_own field = "Dead-Time", inj2Openb, {opentime2_optb_own} field = "Correction Curve", opentime2_optb, {opentime2_optb_own} field = "PWM Current Limiting", opentime2_optb_pwm, {opentime2_optb_own} field = "PWM Current Limit", inj2PwmP2, {opentime2_optb_own && opentime2_optb_pwm} field = "PWM Time Threshold", inj2PwmT2, {opentime2_optb_own && opentime2_optb_pwm} field = "Injector PWM Period", inj2PwmPd2, {opentime2_optb_own && opentime2_optb_pwm} dialog = injCharswest2, "", yAxis panel = injchar_ms3x_2, North panel = injchar_v3_2, South dialog = injsettings2, "", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#injdt2" panel = injCharswest2, West dialog = smallpwwest2, "" field = "Enable Non-Linear Small Pulsewidths", smallpw2_opt1_master field = "(This is for the alternate injectors from dual-fuel)" field = "MS3X Injector A", smallpw2_opt1, { smallpw2_opt1_master } field = "MS3X Injector B", smallpw2_opt2, { smallpw2_opt1_master } field = "MS3X Injector C", smallpw2_opt3, { smallpw2_opt1_master } field = "MS3X Injector D", smallpw2_opt4, { smallpw2_opt1_master } field = "MS3X Injector E", smallpw2_opt5, { smallpw2_opt1_master } field = "MS3X Injector F", smallpw2_opt6, { smallpw2_opt1_master } field = "MS3X Injector G", smallpw2_opt7, { smallpw2_opt1_master } field = "MS3X Injector H", smallpw2_opt8, { smallpw2_opt1_master } field = "" field = "Mainboard Bank 1", smallpw2_opta, { smallpw2_opt1_master } field = "" field = "Mainboard Bank 2", smallpw2_optb, { smallpw2_opt1_master } dialog = smallpw2, "Injector Small Pulsewidths 2", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#injsmallpw2" panel = smallpwwest2, West dialog = smallpwwest, "" field = "Enable Non-Linear Small Pulsewidths", smallpw_opt1_master field = "!CAUTION!" field = "Unless you have specific injector data these" field = "'curves' must be a straight line from 0-2" field = "Ensure the start and end points are equal" field = "(e.g. 0.000, 0.000 and 2.000, 2.000)" field = "Select the pulsewidth curve for each injector" field = "MS3X Injector A", smallpw_opt1, { smallpw_opt1_master && ((hardware_fuel) ) } field = "MS3X Injector B", smallpw_opt2, { smallpw_opt1_master && ((hardware_fuel) && (nInjectors > 1)) } field = "MS3X Injector C", smallpw_opt3, { smallpw_opt1_master && ((hardware_fuel) && (nInjectors > 2)) } field = "MS3X Injector D", smallpw_opt4, { smallpw_opt1_master && ((hardware_fuel) && (nInjectors > 3)) } field = "MS3X Injector E", smallpw_opt5, { smallpw_opt1_master && ((hardware_fuel) && (nInjectors > 4)) } field = "MS3X Injector F", smallpw_opt6, { smallpw_opt1_master && ((hardware_fuel) && (nInjectors > 5)) } field = "MS3X Injector G", smallpw_opt7, { smallpw_opt1_master && ((hardware_fuel) && (nInjectors > 6)) } field = "MS3X Injector H", smallpw_opt8, { smallpw_opt1_master && ((hardware_fuel) && (nInjectors > 7)) } field = "" field = "Mainboard Bank 1", smallpw_opta, { smallpw_opt1_master } field = "" field = "Mainboard Bank 2", smallpw_optb, { smallpw_opt1_master } dialog = smallcurveswest, "", yAxis panel = smallcurve0 panel = smallcurve2 dialog = smallcurveseast, "", yAxis panel = smallcurve1 panel = smallcurve3 dialog = smallcurves, "", xAxis panel = smallcurveswest panel = smallcurveseast dialog = smallpw, "Injector Small Pulsewidths", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#injsmallpw" panel = smallpwwest, West panel = smallcurves, Center dialog = smallpwb, "" field = "Injector I", smallpw_opta, { smallpw_opt1_master && ((hardware_fuel) && (nInjectors > 8)) } field = "Injector J", smallpw_optb, { smallpw_opt1_master && ((hardware_fuel) && (nInjectors > 9)) } field = "Injector K", smallpw_opt11, { smallpw_opt1_master && ((hardware_fuel) && (nInjectors > 10)) } field = "Injector L", smallpw_opt12, { smallpw_opt1_master && ((hardware_fuel) && (nInjectors > 11)) } field = "Injector M", smallpw_opt13, { smallpw_opt1_master && ((hardware_fuel) && (nInjectors > 12)) } field = "Injector N", smallpw_opt14, { smallpw_opt1_master && ((hardware_fuel) && (nInjectors > 13)) } field = "Injector O", smallpw_opt15, { smallpw_opt1_master && ((hardware_fuel) && (nInjectors > 14)) } field = "Injector P", smallpw_opt16, { smallpw_opt1_master && ((hardware_fuel) && (nInjectors > 15)) } dialog = smallpw2b, "" field = "Injector I", smallpw2_opta, { smallpw2_opt1_master && ((hardware_fuel) && (nInjectors > 8)) } field = "Injector J", smallpw2_optb, { smallpw2_opt1_master && ((hardware_fuel) && (nInjectors > 9)) } field = "Injector K", smallpw2_opt11, { smallpw2_opt1_master && ((hardware_fuel) && (nInjectors > 10)) } field = "Injector L", smallpw2_opt12, { smallpw2_opt1_master && ((hardware_fuel) && (nInjectors > 11)) } field = "Injector M", smallpw2_opt13, { smallpw2_opt1_master && ((hardware_fuel) && (nInjectors > 12)) } field = "Injector N", smallpw2_opt14, { smallpw2_opt1_master && ((hardware_fuel) && (nInjectors > 13)) } field = "Injector O", smallpw2_opt15, { smallpw2_opt1_master && ((hardware_fuel) && (nInjectors > 14)) } field = "Injector P", smallpw2_opt16, { smallpw2_opt1_master && ((hardware_fuel) && (nInjectors > 15)) } ; dialog = egoControl, "EGO Control" dialog = egoControlright, "" field = "Algorithm", egoAlgorithm, { egoType } field = "Use EGO Delay Table", egoAlgorithm_delay_table, {egoType && (egoAlgorithm < 3)} field = "Ignition Events Per Step", egoCount, { egoType && (egoAlgorithm < 3) && !egoAlgorithm_delay_table} field = "EGO Sensor Response Time", ego_sensor_delay, { egoType && (egoAlgorithm < 3) && egoAlgorithm_delay_table} field = "Controller Step Size", egoDelta, { egoType && (egoAlgorithm == 0) } field = "Use Authority Table", egoAlgorithm_auth, { egoType } field = "Controller Auth +/-", egoLimit, { egoType && !egoAlgorithm_auth && (egoAlgorithm < 3) } field = "Only Correct Above:", ego_lower_bound, { egoType && (egoAlgorithm < 3) } field = "And Correct Below:", ego_upper_bound, { egoType && (egoAlgorithm < 3) } field = "Active Above Coolant", egoTemp, { egoType && (egoAlgorithm < 3) } field = "Active Above RPM", egoRPM, { egoType && !egoAlgorithm_auth && (egoAlgorithm < 3) } field = "Active Below TPS", TPSOXLimit, { egoType && (egoAlgorithm < 3) } field = "Active Below Load", MAPOXLimit, { egoType && !egoAlgorithm_auth && (egoAlgorithm < 3) } field = "Active Above Load", MAPOXMin, { egoType && !egoAlgorithm_auth && (egoAlgorithm < 3) } field = "EGO Delay After Start", ego_startdelay, { egoType && (egoAlgorithm < 3) } field = "PID Proportional Gain", egoKP, { egoType && (egoAlgorithm == 2) } field = "PID Integral", egoKI, { egoType && (egoAlgorithm == 2) } field = "PID Derivative", egoKD, { egoType && (egoAlgorithm == 2) } dialog = egoports, "",yAxis field = "EGO 1 Port", egoport1 field = "EGO 2 Port", egoport2, {egonum > 1} field = "EGO 3 Port", egoport3, {egonum > 2} field = "EGO 4 Port", egoport4, {egonum > 3} field = "EGO 5 Port", egoport5, {egonum > 4} field = "EGO 6 Port", egoport6, {egonum > 5} field = "EGO 7 Port", egoport7, {egonum > 6} field = "EGO 8 Port", egoport8, {egonum > 7} ; not implemented ; dialog = egoports_tgt, "", yAxis ; field = "AFR target" ; field = "", egomap1t ; field = "", egomap2t, {egonum > 1} ; field = "", egomap3t, {egonum > 2} ; field = "", egomap4t, {egonum > 3} ; field = "", egomap5t, {egonum > 4} ; field = "", egomap6t, {egonum > 5} ; field = "", egomap7t, {egonum > 6} ; field = "", egomap8t, {egonum > 7} dialog = egoports2, "EGO ports", xAxis panel = egoports ; panel = egoports_tgt dialog = egoControlleft, "", yAxis field = "EGO Sensor Type", egoType field = "Number Of Sensors", egonum, { egoType } field = "#Remember to Calibrate and set Project Properties" panel = egoports2 dialog = egoControlmain, "", xAxis panel = egoControlright, West panel = egoControlleft, East dialog = egomap_inj, "", yAxis field = "Injector" field = "MS3X Inj A" field = "MS3X Inj B" field = "MS3X Inj C" field = "MS3X Inj D" field = "MS3X Inj E" field = "MS3X Inj F" field = "MS3X Inj G" field = "MS3X Inj H" field = "V3 Inj 1" field = "V3 Inj 2" dialog = egomap_ego, "", yAxis field = "- Uses Sensor" field = "", egomap1 field = "", egomap2 field = "", egomap3 field = "", egomap4 field = "", egomap5 field = "", egomap6 field = "", egomap7 field = "", egomap8 field = "", egomap9 field = "", egomap10 dialog = egomapping, "AFR / EGO Sensor Mapping", xAxis panel = egomap_inj panel = egomap_ego dialog = egoControl, "AFR / EGO Control", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#egocont" panel = egoControlmain, West panel = egomapping, East dialog = egomap_inj2, "", yAxis field = "Injector" field = "InjI" field = "InjJ" field = "InjK" field = "InjL" field = "InjM" field = "InjN" field = "InjO" field = "InjP" dialog = egomap_ego2, "", yAxis field = "Sensor" field = "", egomap9 field = "", egomap10 field = "", egomap11 field = "", egomap12 field = "", egomap13 field = "", egomap14 field = "", egomap15 field = "", egomap16 dialog = egomapping2, "AFR / EGO Sensor Mapping", xAxis panel = egomap_inj2 panel = egomap_ego2 dialog = egoports2a, "",yAxis field = "EGO Channel" field = "EGO 9 Port", egoport9, {egonum > 8} field = "EGO 10 Port", egoport10, {egonum > 9} field = "EGO 11 Port", egoport11, {egonum > 10} field = "EGO 12 Port", egoport12, {egonum > 11} field = "EGO 13 Port", egoport13, {egonum > 12} field = "EGO 14 Port", egoport14, {egonum > 13} field = "EGO 15 Port", egoport15, {egonum > 14} field = "EGO 16 Port", egoport16, {egonum > 15} dialog = egocont9_16, "AFR / EGO(9-16)", border panel = egoports2a, West panel = egomapping2, East dialog = ignitionOptions, "" field = "Spark Mode (Dizzy, EDIS, Wheel)", spk_mode0 ; ! field = "Trigger Angle/Offset", triggerOffset, { (spk_mode0 != 31) && (spk_mode0 != 4)} field = "Angle Between Main And Return", trigret_ang, { spk_mode0 ==12} field = "Oddfire First Angle", OddFireang, { (engineType == 1) && (spk_mode0 < 31) && (spk_conf2_oddodd != 3) } field = "HEI/GMDIS, TFI, C3I Options", spk_conf2_gmtfi, {(spk_mode0 == 2) || (spk_mode0 == 4)} field = "Oddfire Phasing", spk_conf2_oddodd, { (engineType == 1) && (spk_mode0==4)} field = "Skip Pulses", no_skip_pulses field = "Ignition Input Capture", ICIgnCapture ; ! field = "Spark Output", spkout_hi_lo2, {spk_mode0 != 31} ; field = "Number Of Coils", spk_mode3 field = "Spark Hardware In Use", hardware_spk field = "Cam Input (If Used)", hardware_cam field = "Tertiary Tach Input", spk_mode3_tach3, {spk_mode0 == 47} field = "Flip Polarity On Hi-Res Tach", spk_mode3_hirespol, {((spk_mode0 >= 32) && (spk_mode0 <= 39)) || (spk_mode0 == 47)} dialog = moreIgnitionOptions, "" field = "Fixed Advance", timing_flags field = "Use Prediction", use_prediction field = "Timing for Fixed Advance", fixed_timing, { timing_flags == 1 }; field = "Cranking Dwell", crank_dwell field = "Cranking Advance", crank_timing, {!(spk_mode0 == 2 && triggerOffset < 20) } field = "" field = "Toyota Multiplex", spk_conf2_dli, {spk_mode0 > 2} field = "Dwell type", dwellmode field = "Use Dwell vs Rpm Curve", spk_conf2_dwell, {dwellmode ==2} field = "Use Dwell Table", spk_conf2_dwelltbl, {dwellmode ==0} field = "Nominal Dwell", max_coil_dur, {(spk_mode0 >1) && (dwellmode==0) && (spk_conf2_dwelltbl==0)} field = "Spark Duration", max_spk_dur, {(spk_mode0 >1) && (dwellmode==0) } field = "Dwell Time", dwelltime, {(spk_mode0 >1) && (dwellmode==2) && (spk_conf2_dwell==0)} field = "Dwell Duty", dwellduty, {(spk_mode0 >1) && (dwellmode==1) } field = "NOTE: Spark hardware latency should ONLY be used if" field = "you notice spark retard with increasing rpms." field = "Spark Hardware Latency", hw_latency field = "Middle LED indicator", feature4_0igntrig, { (spk_mode0 == 3) } field = "Spark Trim", spk_mode3_trim dialog = triggerWheel, "" field = "Trigger Wheel Arrangement", spk_config_trig2, { spk_mode0 == 4 } field = "Trigger Wheel Teeth", triggerTeeth, { (spk_mode0 == 4) || (spk_mode0 == 47) } field = "Missing Teeth", No_Miss_Teeth, {(spk_config_trig2 != 2) && (spk_mode0 == 4)} field = "Tooth #1 Angle", Miss_ang, { (spk_mode0 == 4) || (spk_mode0 == 47) } field = "Main Wheel Speed", spk_config_camcrank, { (spk_mode0 == 4) || ((spk_mode0 == 14) && (nCylinders == 2))} field = "Second Trigger Active On", spk_config_trig2l, {(spk_config_trig2 & 0x2) && spk_mode0 == 4} field = "Level For Phase 1", spk_config_campol, {((spk_config_trig2l & 0x3) == 0x3) && (spk_mode0 == 4) && (spk_config_trig2 == 3)} field = "Check At Tooth#", poll_level_tooth, {((spk_config_trig2l & 0x3) == 0x3) && (spk_mode0 == 4) && (spk_config_trig2 == 3)} field = "And Every Rotation Of..", spk_config_resetcam, {((spk_config_trig2 & 0x3) == 0x2) && spk_mode0 == 4} dialog = padignition field = "" dialog = westIgnitionOptions, "", yAxis panel = ignitionOptions panel = triggerWheel dialog = oddfireangles1, "" field = "Custom Oddfire Angles In Sequence From #1" dialog = oddfireangles3, "", xAxis field = "1st", oddfireangs1, {(spk_conf2_oddodd == 3) && (engineType == 1) && (spk_mode0==4)} field = "2nd", oddfireangs2, {(spk_conf2_oddodd == 3) && (engineType == 1) && (spk_mode0==4)} dialog = oddfireangles5, "", xAxis field = "3rd", oddfireangs3, {(spk_conf2_oddodd == 3) && (engineType == 1) && (spk_mode0==4)} field = "4th", oddfireangs4, {(spk_conf2_oddodd == 3) && (engineType == 1) && (spk_mode0==4)} dialog = eastIgnitionOptions, "", yAxis panel = moreIgnitionOptions panel = oddfireangles1 panel = oddfireangles3 panel = oddfireangles5 dialog = combinedignition, "Ignition Options / Wheel Decoder", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#ignopts" panel = westIgnitionOptions, West panel = eastIgnitionOptions, East dialog = northwestidle, "", yAxis field = "Idle Valve Type", IdleCtl field = "Algorithm", IdleCtl_alg, {IdleCtl > 1} dialog = northeastidle, "", yAxis field = "Fast Idle Temperature", fastIdleT, { IdleCtl == 1 } field = "Hysteresis", IdleHyst, { IdleCtl == 1 } dialog = westidle, "Stepper Idle" field = "Time Step Size", IACtstep, { IdleCtl == 3 } field = "Initial Time Step Size", IAC_tinitial_step, { IdleCtl == 3 } field = "Minimum # Steps To Move", IACminstep, { IdleCtl == 3 } field = "Homing Steps", IACStart, { IdleCtl == 3 } field = "Homing Direction", IdleCtl_home, { IdleCtl == 3 } field = "Wide Open Steps", iacfullopen, { IdleCtl_home && (IdleCtl == 3) } field = "Crank-to-Run Taper Time", IACcrankxt, { (IdleCtl == 3) && (IdleCtl_alg == 0) } field = "Power Between Steps", IACcurlim, { IdleCtl == 3 } dialog = eastidle, "PWM Idle" field = "Crank-to-Run Taper Time", pwmidlecranktaper, { IdleCtl == 2 } field = "" field = "Valve mode", pwmidleset_inv, { IdleCtl == 2 } field = "Run Valve Before Start", pwmidle_freq_koeo, { IdleCtl == 2 } field = "Output Port", pwmidle_freq_pin, { (IdleCtl == 1) || (IdleCtl == 2) } field = "3 Wire Mode", pwmidle_freq_pin3, { IdleCtl == 2 } field = "Frequency", pwmidle_freq_scale, { IdleCtl == 2 } field = "This frequency may be shared with boost control" dialog = northidle, "", border panel = northwestidle, West panel = northeastidle, East dialog = southidle, "", border panel = westidle, West panel = eastidle, East dialog = combinedidle, "Idle Control", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#idle" panel = northidle, North panel = southidle, South dialog = pwmidle_closedloop_pwm, "Closed-Loop Idle Valve Settings" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#clidle" field = "Idle Valve Minimum Duty", pwmidle_closed_duty, { (IdleCtl == 2) && (IdleCtl_alg == 1) } field = "Idle Valve Maximum Duty", pwmidle_open_duty, { (IdleCtl == 2) && (IdleCtl_alg == 1) } field = "Dashpot Adder", pwmidle_dp_adder, { (IdleCtl == 2) && (IdleCtl_alg == 1) } field = "Use Last Value Or Table", pwmidle_cl_opts_initvaluetable field = "Use CLT Or MAT In Table Lookup", pwmidle_cl_opts_initval_clt, { pwmidle_cl_opts_initvaluetable } field = "Close Delay (0 Means Do Not Close)", pwmidle_close_delay field = "Shift Settings" field = "Leave Valve Closed Above:", pwmidle_shift_lower_rpm, { pwmidle_close_delay > 0 } field = "For This Number Of Seconds:", pwmidle_shift_open_time, { pwmidle_close_delay > 0 } dialog = pwmidle_closedloop_stepper, "Closed-Loop Idle Valve Settings" field = "Idle Valve Minimum Steps", pwmidle_closed_steps, { (IdleCtl == 3) } field = "Idle Valve Maximum Steps", pwmidle_open_steps, { (IdleCtl == 3) } field = "Dashpot Adder", pwmidle_dp_adder_steps field = "Use Last Value Or Table", pwmidle_cl_opts_initvaluetable field = "Use CLT Or MAT In Table Lookup", pwmidle_cl_opts_initval_clt, { pwmidle_cl_opts_initvaluetable } field = "Close Delay (0 Means Do Not Close)", pwmidle_close_delay field = "Shift Settings" field = "Leave Valve Closed Above:", pwmidle_shift_lower_rpm, { pwmidle_close_delay > 0 } field = "For This Number Of Seconds:", pwmidle_shift_open_time, { pwmidle_close_delay > 0 } dialog = pwmidle_closedloop, "", card panel = pwmidle_closedloop_pwm, Center, { IdleCtl == 2 } panel = pwmidle_closedloop_stepper, Center, { IdleCtl == 3 } dialog = pwmidle_PID_gains, "Closed-Loop Idle PID Gains" slider = "Closed-Loop Sensitivity", pwmidle_max_rpm_new, horizontal field = "Tuning Mode", pwmidle_cl_opts_display_pid field = "Proportional Gain", pwmidle_Kp_new, { pwmidle_cl_opts_display_pid } field = "Integral Gain", pwmidle_Ki_new, { pwmidle_cl_opts_display_pid } field = "Derivative Gain", pwmidle_Kd_new, { pwmidle_cl_opts_display_pid } dialog = pwmidle_PID_behavior, "Closed-Loop Idle PID Delays And Behavior" field = "PID Delay", pwmidle_pid_wait_timer field = "Crank To Run Taper", pwmidlecranktaper field = "PID Ramp To Target Time", pwmidle_targ_ramptime field = "PID Control Interval", pwmidle_ms field = "PID Disable RPMdot", pwmidle_rpmdot_disablepid, { IdleCtl_vss != 1 } dialog = pwmidle_PID_activation, "Closed-Loop Idle PID Activation Settings" field = "Use VSS To Activate PID", IdleCtl_vss field = "Minimum VSS1", idleminvss, {IdleCtl_vss} field = "Idle Activation TPS Threshold", pwmidle_tps_threshold field = "RPMdot Threshold", pwmidle_rpmdot_threshold, { IdleCtl_vss != 1 } field = "Max Decel Load", pwmidle_decelload_threshold, { IdleCtl_vss != 1 } dialog = pwmidle_empty, "" field = "" field = "" field = "" field = "" field = "" field = "" dialog = pwmidle_west_panel, "", border panel = pwmidle_closedloop, North panel = pwmidle_PID_gains, Center dialog = pwmidle_mid_panel, "", border panel = pwmidle_PID_behavior, North panel = pwmidle_PID_activation, Center panel = pwmidle_empty, South dialog = combinedCLidle, "Closed-Loop Idle Settings", border panel = pwmidle_mid_panel, Center panel = pwmidle_west_panel, West ; first accel page dialog = accelsettings, "Accel Enrich Settings" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#aeset" field = "Use Time-Based or Accel-Pump Accel", AE_options field = "Wall-Wetting AE (EAE, X-tau)", EAEOption field = "TPSdot Uses %WOT", feature7_aetpswot field = "X-Tau MAPdot Thresholds for transition to X, Tau Decel Tables" field = "Start Transition", MapThreshXTD, {EAEOption > 2} field = "Finish Transition", MapThreshXTD2, {EAEOption > 2} ;time based AE dialog = time_ae_south_west, "" field = "Accel MAPdot threshold", mapThresh field = "End Pulsewidth", aeEndPW field = "Time Or Ignition Events", feature7_aeevents field = "Accel Duration", tpsasync_events, { feature7_aeevents } field = "Accel Taper", tpsasync2_events, { feature7_aeevents } field = "Accel Time", taeTime, { !feature7_aeevents } field = "Accel Taper Time", aeTaperTime, { !feature7_aeevents } dialog = time_ae_south_east, "" field = "Accel TPSdot Threshold", tpsThresh field = "Decel Fuel Amount", tdePct field = "Cold Accel Adder", taeColdA field = "Cold Accel Multiplier", taeColdM field = "Accel Enrich Down-Scaling With RPM" field = "Full Accel Below:", ae_lorpm, { !feature7_aeevents } field = "Zero Accel Above:", ae_hirpm, { !feature7_aeevents } dialog = time_ae_south_south, "", xAxis panel = time_ae_south_west panel = time_ae_south_east dialog = time_ae_south, "", yAxis liveGraph = timeaeGraph, "AE Graph", South graphLine = afr1 graphLine = TPSdot, "%", -2000, 2000, auto, auto graphLine = MAPdot, "%", -2000, 2000, auto, auto panel = time_ae_south_south dialog = time_ae_mid, "" slider = "Accel Rnrichment MAPdot<->TPSdot Blend.", tpsProportion, horizontal dialog = time_ae_north, "", xAxis panel = time_accel_mapdot_curve, West, {tpsProportion < 100} panel = time_accel_tpsdot_curve, East, {tpsProportion > 0} dialog = AEtime_settings, "Time-Based Accel Enrichment", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#aetime" panel = time_ae_north panel = time_ae_mid panel = time_ae_south ;accel-pump dialog = pump_ae_south_west, "" field = "Accel MAPdot Threshold", accel_mapdot_threshold, { accel_blend_percent < 100 } field = "Accel TPSdot Threshold", accel_tpsdot_threshold, { accel_blend_percent > 0 } field = "Cold Accel Multiplier", accel_CLT_multiplier dialog = pump_ae_south_east, "" field = "Accel Enrich Down-Scaling With RPM" field = "Full Accel Below:", ae_lorpm, { !feature7_aeevents } field = "Zero Accel Above:", ae_hirpm, { !feature7_aeevents } dialog = pump_ae_south_south, "", xAxis panel = pump_ae_south_west panel = pump_ae_south_east dialog = pump_ae_south, "", yAxis liveGraph = pump_ae_Graph, "AE Graph", South graphLine = afr1 graphLine = TPSdot, "%", -2000, 2000, auto, auto graphLine = MAPdot, "%", -2000, 2000, auto, auto panel = pump_ae_south_south dialog = pump_ae_north, "", xAxis panel = pump_accel_mapdot_curve, West, {accel_blend_percent < 100} panel = pump_accel_tpsdot_curve, East, {accel_blend_percent > 0} dialog = pump_ae_mid, "" slider = "Accel Enrichment MAPdot<->TPSdot Blend.", accel_blend_percent, horizontal dialog = AEpump_settings, "Accel-Pump Accel Enrichment", yAxis topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#accelpump" panel = pump_ae_north panel = pump_ae_mid panel = pump_ae_south dialog = sensorCal, "Calibrate MAP/Baro" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#calmapbaro" field = "#MAP Sensor" #if INI_VERSION_2 settingSelector = "Common MAP Sensors" settingOption = "MPX4115", map0=10.6, mapmax=121.7 settingOption = "MPX4250", map0=10, mapmax=260 settingOption = "GM 1-BAR", map0=10, mapmax=105 settingOption = "GM 2-BAR", map0=8.8, mapmax=208 settingOption = "GM 3-BAR / MPXH6300", map0=1.1, mapmax=315.5 settingOption = "MPXH6400", map0=3.5, mapmax=416.5 settingOption = "AEM 3.5 BAR", map0=-42.3, mapmax=386.3 settingOption = "AEM 5.0 BAR", map0=-64.6, mapmax=581.7 #endif field = "Value At 0.0 Volts", map0 field = "Value At 5.0 Volts", mapmax field = "#Barometer Sensor (usually identical to MAP)" #if INI_VERSION_2 settingSelector = "Common Baro Sensors" settingOption = "MPX4115", baro0=10.6, baromax=121.7 settingOption = "MPX4250", baro0=10, baromax=260 settingOption = "GM 1-BAR", baro0=10, baromax=105 settingOption = "GM 2-BAR", baro0=8.8, baromax=208 settingOption = "GM 3-BAR / MPXH6300",baro0=1.1, baromax=315.5 settingOption = "MPXH6400", baro0=3.5, baromax=416.5 settingOption = "AEM 3.5 BAR", map0=-42.3, mapmax=386.3 settingOption = "AEM 5.0 BAR", map0=-64.6, mapmax=581.7 #endif field = "Value At 0.0 Volts", baro0 field = "Value At 5.0 Volts", baromax field = "#Barometric Correction" field = "At Total Vacuum ", bcor0 field = "Rate", bcormult dialog = knockSettings3, "Knock Sensor Settings" field = "Knock Control", knk_option field = "Input Type", knk_option_an, { knk_option } field = "Knock Input Pin", knkport, { knk_option && !knk_option_an } field = "Knock Indicated By:", knkDirection, { knk_option && !knk_option_an } field = "Pullup/Down On Input", knkpull, { knk_option && !knk_option_an } field = "Input Pin", knkport_an, { knk_option && (knk_option_an == 1) } field = "Window Sample Type", knk_option_wind, { knk_option && (knk_option_an == 1) } field = "Window Output", knk_pin_out, { knk_option && (knk_option_an < 2) } field = "#Detection" field = "Knock Count", knk_ndet, { knk_option > 0 } field = "Knock Ignored Above MAP", knk_maxmap, { knk_option > 0 } field = "RPM Window Low", knk_lorpm, { knk_option > 0 } field = "RPM Window High", knk_hirpm, { knk_option > 0 } field = "Ignore During Launch/Flatshift", knock_conf_launch, { knk_option > 0 } field = "#Retarding" field = "Maximum Retard", knk_maxrtd, { knk_option > 0 } field = "Retard Check Time", knk_trtd, { knk_option > 0 } field = "Retard Coarse Step Size", knk_step1, { knk_option > 0 } field = "Retard Fine Step Size", knk_step2, { knk_option > 0 } field = "#Recovery" field = "Advance Check Time", knk_tadv, { knk_option > 0 } field = "Advance Step Size", knk_step_adv, { knk_option > 0 } field = "Recovery Advance", knk_dtble_adv, { knk_option == 1 } dialog = ks4a, "", yAxis field = "Cyl#" field = "1" field = "2" field = "3" field = "4" field = "5" field = "6" field = "7" field = "8" #if CYL_12_16_SUPPORT field = "9" field = "10" field = "11" field = "12" field = "13" field = "14" field = "15" field = "16" #endif dialog = ks4b, "", yAxis field = "Gain" field = "", knock_gain01 field = "", knock_gain02, {knock_conf_percyl && (nCylinders >1)} field = "", knock_gain03, {knock_conf_percyl && (nCylinders >2)} field = "", knock_gain04, {knock_conf_percyl && (nCylinders >3)} field = "", knock_gain05, {knock_conf_percyl && (nCylinders >4)} field = "", knock_gain06, {knock_conf_percyl && (nCylinders >5)} field = "", knock_gain07, {knock_conf_percyl && (nCylinders >6)} field = "", knock_gain08, {knock_conf_percyl && (nCylinders >7)} #if CYL_12_16_SUPPORT field = "", knock_gain09, {knock_conf_percyl && (nCylinders >8)} field = "", knock_gain10, {knock_conf_percyl && (nCylinders >9)} field = "", knock_gain11, {knock_conf_percyl && (nCylinders >10)} field = "", knock_gain12, {knock_conf_percyl && (nCylinders >11)} field = "", knock_gain13, {knock_conf_percyl && (nCylinders >12)} field = "", knock_gain14, {knock_conf_percyl && (nCylinders >13)} field = "", knock_gain15, {knock_conf_percyl && (nCylinders >14)} field = "", knock_gain16, {knock_conf_percyl && (nCylinders >15)} #endif dialog = ks4c, "", yAxis field = "Sensor" field = "", knock_sens01 field = "", knock_sens02, {knock_conf_percyl && (nCylinders >1)} field = "", knock_sens03, {knock_conf_percyl && (nCylinders >2)} field = "", knock_sens04, {knock_conf_percyl && (nCylinders >3)} field = "", knock_sens05, {knock_conf_percyl && (nCylinders >4)} field = "", knock_sens06, {knock_conf_percyl && (nCylinders >5)} field = "", knock_sens07, {knock_conf_percyl && (nCylinders >6)} field = "", knock_sens08, {knock_conf_percyl && (nCylinders >7)} #if CYL_12_16_SUPPORT field = "", knock_sens09, {knock_conf_percyl && (nCylinders >8)} field = "", knock_sens10, {knock_conf_percyl && (nCylinders >9)} field = "", knock_sens11, {knock_conf_percyl && (nCylinders >10)} field = "", knock_sens12, {knock_conf_percyl && (nCylinders >11)} field = "", knock_sens13, {knock_conf_percyl && (nCylinders >12)} field = "", knock_sens14, {knock_conf_percyl && (nCylinders >13)} field = "", knock_sens15, {knock_conf_percyl && (nCylinders >14)} field = "", knock_sens16, {knock_conf_percyl && (nCylinders >15)} #endif dialog = ks4bot, "", xAxis panel = ks4a panel = ks4b panel = ks4c dialog = ks4top, "" field = "NOTE! This feature is only licensed for use" field = "with JSM add-on board" field = "Bandpass Frequency (kHz)", knock_bpass field = "Integrator Time constant (us)", knock_int field = "Number of Sensors", knock_conf_num field = "Monitor Per Cylinder", knock_conf_percyl field = "Knock gain:" dialog = knockSettings4, "Knock Sensor Parameters", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#knockparam" panel = ks4top, North panel = ks4bot, South dialog = knockSettings, "Knock Sensor Settings", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#knock" panel = knockSettings3, West panel = knockthresh_curve, East dialog = knockSettings2, "Knock Window Settings", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#knockwindow" panel = knockstart_curve, North panel = knockduration_curve, South dialog = idleAdvancemenu, "Idle Advance Settings" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#idleadv" field = "Idle Advance On", idleadvance_on field = "Idle RPM Timing Correction", idle_special_ops_timing_assist field = "Go to idle advance/Idle RPM timing correction when:" field = "PID Idle Activates", idleveadv_to_pid_idleadv, { idleadvance_on || idle_special_ops_timing_assist } field = "TPS Is Below:", idleadvance_tps, { (idleadvance_on || idle_special_ops_timing_assist) && !idleveadv_to_pid_idleadv } field = "And RPM Is Below:", idleadvance_rpm, { (idleadvance_on || idle_special_ops_timing_assist) && !idleveadv_to_pid_idleadv } field = "And Load Is Above:", idleadvance_load, { (idleadvance_on || idle_special_ops_timing_assist) && !idleveadv_to_pid_idleadv } field = "And CLT Is Above:", idleadvance_clt, { (idleadvance_on || idle_special_ops_timing_assist) && !idleveadv_to_pid_idleadv } field = "And After Delay:", idleadvance_delay, { (idleadvance_on || idle_special_ops_timing_assist) && !idleveadv_to_pid_idleadv } dialog = idleAdvance, "Idle Advance Settings", border panel = idleAdvancemenu, West panel = idleAdvance_curve, East dialog = idleVemenu, "Idle VE settings" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#idleve" field = "Idle VE On", idleve_on field = "Go to idle VE when:" field = "PID Idle Activates", idleveadv_to_pid_idleve, { idleve_on } field = "TPS Is Below:", idleve_tps, { idleve_on && !idleveadv_to_pid_idleve } field = "And RPM Is Below:", idleve_rpm, { idleve_on && !idleveadv_to_pid_idleve } field = "And load Is Above:", idleve_load, { idleve_on && !idleveadv_to_pid_idleve } field = "And CLT Is Above:", idleve_clt, { idleve_on && !idleveadv_to_pid_idleve } field = "And VSS Zero?", idleve_vsson, { idleve_on && !idleveadv_to_pid_idleve } field = "And After Delay:", idleve_delay, { idleve_on && !idleveadv_to_pid_idleve } dialog = idleVeTables_n, "Idle VE Table" panel = idleve1Tbl, North, { idleve_on } dialog = idleVeTables_s, "Idle VE Table - Dual Fuel" panel = idleve2Tbl, South, { idleve_on && dualfuel_sw_on } dialog = idleVeTables, "", yAxis panel = idleVeTables_n panel = idleVeTables_s dialog = idleVe, "Idle VE", border panel = idleVemenu, West panel = idleVeTables, Center dialog = setbaud, "Megasquirt Baud Rate" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#baud" field = "#The main baud rate should normally be 115200" field = "Megasquirt Baud Rate", baud field = "9600, 19200, 38400, 57600, 115200 only" field = "SDcard Readback Baud Rate", baudhigh field = "up to 230400 only" field = "Set these, Burn" field = "Then adjust tuning software comms baud rate to match" field = "Then powercycle Megasquirt" field = "Use High Speed Runtime", scatterRuntimeEnabled ; not for production ; commandButton = "Test low baud", cmdbaudlow ; commandButton = "Test high baud", cmdbaudhigh dialog = userdefined, "User Defined Menu" field = "Feature Enabled", user_conf0 field = "Mode", user_conf1, { user_conf0 } ; <---- this bit here greys the control out if the bit isn't set field = "Value 1", user_value1, { user_conf0 } field = "Value 2", user_value2, { user_conf0 } dialog = generic_pid_left_a, "" field = "Enable", generic_pid_flags_a_on field = "Closed-loop (PID) type", generic_pid_flags_a_type, { generic_pid_flags_a_on } channelSelector= "Load Axis", generic_pid_load_offset_a, generic_pid_load_size_a, { generic_pid_flags_a_on } channelSelector= "Feedback Input Variable (PV)", generic_pid_PV_offset_a, generic_pid_PV_size_a, { generic_pid_flags_a_on } field = "Max Feedback Input", generic_pid_upper_inputlim_a, { generic_pid_flags_a_on } field = "Min Feedback Input", generic_pid_lower_inputlim_a, { generic_pid_flags_a_on } field = "Control Output Port/Pin", generic_pid_pwm_outs_a, { generic_pid_flags_a_on } field = "Frequency" , generic_pid_pwm_opts_freq_a, { generic_pid_flags_a_on } field = "Max Control Output", generic_pid_output_upperlim_a, { generic_pid_flags_a_on } field = "Min Control Output", generic_pid_output_lowerlim_a, { generic_pid_flags_a_on } field = "Output Polarity", generic_pid_flags_a_direction, { generic_pid_flags_a_on } ; field = "Generic PID direction", generic_pid_flags_a_direction, { generic_pid_flags_a_on } ; field = "Generic PID use stepper", generic_pid_flags_a_output_type, { generic_pid_flags_a_on } ; field = "Generic PID use table or curve", generic_pid_flags_a_lookup_type, { generic_pid_flags_a_on } field = "Control Interval", generic_pid_control_interval_a, { generic_pid_flags_a_on } field = "P Term", generic_pid_P_a, { generic_pid_flags_a_on } field = "I Term", generic_pid_I_a, { generic_pid_flags_a_on } field = "D Term", generic_pid_D_a, { generic_pid_flags_a_on } field = "CLT/MAT Units", sensor_temp, {0} dialog = generic_pid_curve_grapha, "", card panel = generic_pid_Tbl_a, Center, { generic_pid_flags_a_on } dialog = generic_pid_a, "Generic Closed-Loop A", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#gencl" panel = generic_pid_left_a, West panel = generic_pid_curve_grapha, Center dialog = generic_pid_left_b, "" field = "Enable", generic_pid_flags_b_on field = "Closed-Loop (PID) Type", generic_pid_flags_b_type, { generic_pid_flags_b_on } channelSelector= "Load Axis", generic_pid_load_offset_b, generic_pid_load_size_b, { generic_pid_flags_b_on } channelSelector= "Feedback Input Variable (PV)", generic_pid_PV_offset_b, generic_pid_PV_size_b, { generic_pid_flags_b_on } field = "Max Feedback Input", generic_pid_upper_inputlim_b, { generic_pid_flags_b_on } field = "Min Feedback Input", generic_pid_lower_inputlim_b, { generic_pid_flags_b_on } field = "Control Output Port/Pin", generic_pid_pwm_outs_b, { generic_pid_flags_b_on } field = "Frequency" , generic_pid_pwm_opts_freq_b, { generic_pid_flags_b_on } field = "Max Control Output", generic_pid_output_upperlim_b, { generic_pid_flags_b_on } field = "Min Control Output", generic_pid_output_lowerlim_b, { generic_pid_flags_b_on } field = "Output Polarity", generic_pid_flags_b_direction, { generic_pid_flags_b_on } ; field = "Generic PID direction", generic_pid_flags_b_direction, { generic_pid_flags_b_on } ; field = "Generic PID use stepper", generic_pid_flags_b_output_type, { generic_pid_flags_b_on } ; field = "Generic PID use table or curve", generic_pid_flags_b_lookup_type, { generic_pid_flags_b_on } field = "Control Interval", generic_pid_control_interval_b, { generic_pid_flags_b_on } field = "P Term", generic_pid_P_b, { generic_pid_flags_b_on } field = "I Term", generic_pid_I_b, { generic_pid_flags_b_on } field = "D Term", generic_pid_D_b, { generic_pid_flags_b_on } field = "CLT/MAT Units", sensor_temp, {0} dialog = generic_pid_curve_graphb, "", card panel = generic_pid_Tbl_b, Center, { generic_pid_flags_b_on } dialog = generic_pid_b, "Generic Closed-Loop B", border topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#gencl" panel = generic_pid_left_b, West panel = generic_pid_curve_graphb, Center ;------------------------------------------------------------------------------- ; General help text help = helpGeneral, "Megasquirt 3 General Help" webHelp = "http://www.msextra.com/" text = "For current documentation, click the Web Help button," text = "or visit http://www.msextra.com/." text = "
" text = "
Megasquirt firmware is copyright and is only licensed for use on approved hardware." text = "
See the LICENSE text supplied with your firmware." text = "
" text = "
To see legal Megasquirts, visit http://www.msextra.com/doc/general/whatmegasquirt.html" ;------------------------------------------------------------------------------- #if INI_VERSION_2 [PortEditor] ; spare ports ; map the arrays and supply the labels. ; all arrays are expected to be the same length in the first dimension ; thus a [ 7] array will be 7 ports in length and expect 7 labels ; The second dimension will drive the number of conditions per array. ; thus a [7x2] array will have 2 conditions joined by the conditionRelationship. ; a [7x3] will have up to 3 conditions. portEditor = ms3_port_edit, "Programmable On/Off Outputs" ; 1st the array constant, then the labels in the index order. enabledPorts = psEnabled, "PM3 - Injection LED D14", "PM4 - Accel LED D16", "PM5 - Warmup LED D15", "PJ0 - IAC2", "PJ1 - IAC1", "PJ7 - JS11", "PP2 - Idle", "PP3 - Boost", "PP4 - Nitrous 1", "PP5 - Nitrous 2", "PP6 - VVT", "PP7 - Fidle", "PT1 - V3 Inj 1", "PT3 - V3 Inj 2", "PT5 - JS10", "PK0 - Tacho", "PA0 - Inj A", "PA1 - Inj B", "PA2 - Inj C", "PA3 - Inj D", "PA4 - Inj E", "PA5 - Inj F", "PA6 - Inj G", "PA7 - Inj H", "PB0 - Spk A", "PB1 - Spk B", "PB2 - Spk C", "PB3 - Spk D", "PB4 - Spk E", "PB5 - Spk F", "PB6 - Spk G", "PB7 - Spk H", "CANout01", "CANout02", "CANout03", "CANout04", "CANout05", "CANout06", "CANout07", "CANout08", "CANout09", "CANout10", "CANout11", "CANout12", "CANout13", "CANout14", "CANout15", "CANout16" outputOffset = psOutOffset outputSize = psOutSize operators = psCondition, "<", "=", ">", "&" ; the actual ASCII value of the operator will be sent to the controller threshold = psThreshold hysteresis = psHysteresis powerOnValue = psInitValue triggerValue = psPortValue conditionRelationship = psConnector, " ", "|", "&" activateOption = extendedDataInSize activateOption = filter32BitChannels #endif ;------------------------------------------------------------------------------- [CurveEditor] curve = vsslaunch_curve, "RPM Limit vs. Speed" columnLabel = "Speed", "RPM limit", "Retard" xAxis = 0, { prefSpeedUnits == 0 ? 50 : 80 }, 9 yAxis = 0, {rpmhigh}, 9 ; xAxis = 0, { prefSpeedUnits == 0 ? 50 : 80 }, 9 ; yAxis = 0, 30, 9 xBins = vsslaunch_vss yBins = vsslaunch_rpm yBins = vsslaunch_retard curve = cranktaper_curvee, "Cranking Taper Curve (Events)" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#crankingtaper" columnLabel = "Events", "%fuel" xAxis = 0, 1000, 5 yAxis = 0, 500, 5 xBins = cranktaper_timeevents yBins = cranktaper_pct curve = cranktaper_curvet, "Cranking Taper Curve (Time)" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#crankingtaper" columnLabel = "Time", "%fuel" xAxis = 0, 25.5, 5 yAxis = 0, 500, 5 xBins = cranktaper_time yBins = cranktaper_pct curve = oil_curve, "Min/Max Oil Pressure vs. RPM" columnLabel = "RPM", "Min", "Max" xAxis = 0, {rpmhigh}, 6 yAxis = 0, 300, 6 xBins = oil_rpm, rpm yBins = oil_press_min yBins = oil_press_max lineLabel = "Min. pressure" lineLabel = "Max. pressure" curve = hpte_curve, "Enrichment vs. Time" columnLabel = "Time", "AFR decrease" xAxis = 0, 25.5, 6 yAxis = 0, 3, 6 xBins = hpte_times yBins = hpte_afrs curve = fp_temp_curve, "Temperature Adjustment (Primary Fuel)" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#fueltemp1" columnLabel = "Temperature", "adj %" xAxis = -40, 220, 9 yAxis = -200, 200, 6 xBins = fp_temps, fuel_temp1 yBins = fp_temp_adj curve = fp_press_curve, "Pressure Adjustment (Primary Fuel)" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#fuelpress1" columnLabel = "Differential Pressure", "adj %" xAxis = 200, 600, 9 yAxis = -200, 200, 6 xBins = fp_presss, fuel_press1 yBins = fp_press_adj curve = alternator_linearise, "Duty linearisation" columnLabel = "Calc", "Output" xAxis = 0, 100, 7 yAxis = 0, 100, 7 xBins = alt_dutyin yBins = alt_dutyout curve = alternator_tempcurve, "Target Charge Voltage" columnLabel = "Temperature", "Voltage" xAxis = 0, 100, 6 yAxis = 12, 16, 6 xBins = alternator_temp yBins = alternator_targvolts curve = alternator_outduty, "Alternator Control Duty" columnLabel = "Voltage", "Duty %" xAxis = 12, 16, 6 yAxis = 0, 100, 6 xBins = alternator_dvolts, alt_targv yBins = alternator_dutyv curve = alternator_outfreq, "Alternator Control Frequency" columnLabel = "Voltage", "Freq Hz" xAxis = 12, 16, 6 yAxis = 0, 250, 6 xBins = alternator_fvolts, alt_targv yBins = alternator_freqv curve = pwm_curve_a, "PWM curve A" columnLabel = "Load", "" xAxis = 0, 100, 6 yAxis = 0, 100, 7 xBins = pwm_xaxis_a, pwma_load yBins = pwm_yaxis_a size = 300, 240 curve = pwm_curve_b, "PWM curve B" columnLabel = "Load", "" xAxis = 0, 100, 6 yAxis = 0, 100, 7 xBins = pwm_xaxis_b, pwmb_load yBins = pwm_yaxis_b size = 300, 240 curve = pwm_curve_c, "PWM curve C" columnLabel = "Load", "" xAxis = 0, 100, 6 yAxis = 0, 100, 7 xBins = pwm_xaxis_c, pwmc_load yBins = pwm_yaxis_c size = 300, 240 curve = pwm_curve_d, "PWM curve D" columnLabel = "Load", "" xAxis = 0, 100, 6 yAxis = 0, 100, 7 xBins = pwm_xaxis_d, pwmd_load yBins = pwm_yaxis_d size = 300, 240 curve = pwm_curve_e, "PWM curve E" columnLabel = "Load", "" xAxis = 0, 100, 6 yAxis = 0, 100, 7 xBins = pwm_xaxis_e, pwme_load yBins = pwm_yaxis_e size = 300, 240 curve = pwm_curve_f, "PWM curve F" columnLabel = "Load", "" xAxis = 0, 100, 6 yAxis = 0, 100, 7 xBins = pwm_xaxis_f, pwmf_load yBins = pwm_yaxis_f size = 300, 240 curve = tc_slip_curve, "Slip Threshold vs Knob Input" columnLabel = "Knob Input", "%" xAxis = 0, 100, 6 yAxis = 0, 100, 7 xBins = tcslipx yBins = tcslipy curve = blend1_curve, "VE1 -> VE2" columnLabel = "X", "%" xAxis = 0, 100, 6 yAxis = 0, 100, 7 xBins = blendx1 yBins = blendy1 curve = blend2_curve, "Spk1 -> Spk2" columnLabel = "X", "%" xAxis = 0, 100, 6 yAxis = 0, 100, 7 xBins = blendx2 yBins = blendy2 curve = blend3_curve, "VE1+2 -> VE3+4" columnLabel = "X", "%" xAxis = 0, 100, 6 yAxis = 0, 100, 7 xBins = blendx3 yBins = blendy3 curve = blend4_curve, "Spk1+2 -> Spk3+4" columnLabel = "X", "%" xAxis = 0, 100, 6 yAxis = 0, 100, 7 xBins = blendx4 yBins = blendy4 curve = blend5_curve, "AFR1 -> AFR2" columnLabel = "X", "%" xAxis = 0, 100, 6 yAxis = 0, 100, 7 xBins = blendx5 yBins = blendy5 curve = blend6_curve, "Boost1 -> Boost2" columnLabel = "X", "%" xAxis = 0, 100, 6 yAxis = 0, 100, 7 xBins = blendx6 yBins = blendy6 curve = blend7_curve, "Crank % 1 -> Crank % 2" columnLabel = "X", "%" xAxis = 0, 100, 6 yAxis = 0, 100, 7 xBins = blendx7 yBins = blendy7 curve = tpswot_curve, "TPS for WOT" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#tpswot" columnLabel = "RPM", "TPS" xAxis = 0, {rpmhigh}, 6 yAxis = 0, 100, 7 xBins = tpswot_rpm, rpm yBins = tpswot_tps curve = launch_retard_time, "Timed Retard After Launch" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#timedretard" columnLabel = "s", "Retard" xAxis = 0, 15, 6 yAxis = 0, 30, 7 xBins = launch_time yBins = launch_retard curve = cl_idle_timing_curve, "Idle RPM Timing Correction Curve" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#idleadvrpm" columnLabel = "RPM delta", "Timing Delta" xAxis = -400, 400, 8 yAxis = -20, 20, 8 xBins = cl_idle_timing_target_deltas yBins = cl_idle_timing_advance_deltas curve = idle_voltage_comp_curve, "PWM Idle Voltage Compensation" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#idlevolt" columnLabel = "Voltage", "Duty" xAxis = 9, 17, 6 yAxis = -10, 10, 6 xBins = idle_voltage_comp_voltage yBins = idle_voltage_comp_delta ;time-based curve = time_accel_mapdot_curve, "MAP based AE" columnLabel = "MAPdot", "Added" xAxis = 0, 1200, 6 yAxis = 0, 48, 4 xBins = maeRates, MAPdot yBins = maeBins ;time-based curve = time_accel_tpsdot_curve, "TPS based AE" columnLabel = "TPSdot", "Added" xAxis = 0, 1200, 6 yAxis = 0, 48, 4 xBins = taeRates, TPSdot yBins = taeBins ;accel-pump curve = pump_accel_mapdot_curve, "Accel MAPdot Curve" columnLabel = "MAPdot", "Added" xAxis = -2000, 2000, 5 yAxis = -200, 200, 5 xBins = accel_mapdots, MAPdot yBins = accel_mapdot_amts ;accel-pump curve = pump_accel_tpsdot_curve, "Accel TPSdot Curve" columnLabel = "TPSdot", "Added" xAxis = -1000, 1000, 5 yAxis = -200, 200, 5 xBins = accel_tpsdots, TPSdot yBins = accel_tpsdot_amts curve = knockstart_curve, "Knock Window Start" columnLabel = "RPM", "deg" xAxis = 0, {rpmhigh}, 6 yAxis = -40, 10, 6 xBins = knock_rpms, rpm yBins = knock_starts curve = knockduration_curve, "Knock Window Duration" columnLabel = "RPM", "deg" xAxis = 0, {rpmhigh}, 6 yAxis = 0, 40, 6 xBins = knock_rpms, rpm yBins = knock_durations curve = knockthresh_curve, "Knock Input Threshold" columnLabel = "RPM", "%" xAxis = 0, {rpmhigh}, 6 yAxis = 0, 100, 6 xBins = knock_rpms, rpm yBins = knock_thresholds gauge = knockinGauge curve = knockupscale_curve, "Knock Coolant Scaling" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#knockcoolant" columnLabel = "clt", "%" xAxis = {cltlowlim}, {clthighlim}, 6 yAxis = 100, 500, 6 xBins = knock_clts, coolant yBins = knock_upscale gauge = cltGauge curve = tc_perfect_curve, "Traction Control - Perfect Run VSS" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#tractionperfectvss" columnLabel = "Time", "VSS" xAxis = 0, 20, 9 yAxis = 0, { prefSpeedUnits == 0 ? 200 : 300 }, 6 xBins = tc_perfect_time yBins = tc_perfect_vss curve = tc_perfectrpm_curve, "Traction Control - Perfect Run RPM" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#tractionperfectrpm" columnLabel = "Time", "RPM" xAxis = 0, 20, 9 yAxis = 0, {rpmhigh}, 6 xBins = tc_perfect_time yBins = tc_perfect_rpm curve = tc_retard_curve, "Spark Retard" columnLabel = "Slip x time", "Retard" xAxis = 0, 100, 5 yAxis = 0, 30, 5 xBins = tc_react_x yBins = tc_retard curve = tc_spkcut_curve, "Spark Cut" columnLabel = "Slip x time", "Spark" xAxis = 0, 100, 5 yAxis = 0, 100, 5 xBins = tc_react_x yBins = tc_spkcut curve = tc_nitrous_curve, "Nitrous%" columnLabel = "Slip x time", "Nitrous" xAxis = 0, 100, 5 yAxis = 0, 100, 5 xBins = tc_react_x yBins = tc_nitrous curve = tc_boost_curve, "Boost Cut" columnLabel = "Slip x Time", "Boost" xAxis = 0, 100, 5 yAxis = 0, 100, 5 xBins = tc_react_x yBins = tc_boost curve = tc_boost_duty_delta_curve, "Boost Duty +/-" columnLabel = "Slip x Time", "Boost Duty +/-" xAxis = 0, 100, 5 yAxis = -100, 100, 5 xBins = tc_react_x yBins = tc_boost_duty_delta curve = tc_addfuel_curve, "Add Fuel" columnLabel = "Slip x time", "Added Fuel" xAxis = 0, 100, 5 yAxis = 0, 100, 5 xBins = tc_react_x yBins = tc_addfuel curve = dualfuel_temp_curve, "Temperature Adjustment (Secondary Fuel)" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#fueltemp2" columnLabel = "Temperature", "Adj %" xAxis = -40, 220, 9 yAxis = -200, 200, 6 xBins = dualfuel_temp, fuel_temp2 yBins = dualfuel_temp_adj curve = dualfuel_press_curve, "Pressure Adjustment (Secondary Fuel)" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#fuelpress2" columnLabel = "Differential Pressure", "Adj %" xAxis = 200, 600, 9 yAxis = -200, 200, 6 xBins = dualfuel_press, fuel_press2 yBins = dualfuel_press_adj curve = primingPW2, "Priming Pulse 2" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#primep2" columnLabel = "Coolant", "Prime PW" xAxis = -40, {clthighlim}, 9 yAxis = 0, 20, 5 xBins = temp_table_p21, coolant, readonly yBins = primePWTable2 gauge = cltGauge curve = crankingPW2, "Cranking Pulse % 2" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#crankp2" columnLabel = "Coolant", "Cranking PW%" xAxis = -40, {clthighlim}, 9 yAxis = 0, 500, 6 xBins = temp_table_p21, coolant yBins = crankPctTable2 gauge = cltGauge curve = asePct2, "Afterstart Enrichment (ASE) Percentage 2" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#asep2" columnLabel = "Coolant", "Afterstart" xAxis = -40, {clthighlim}, 9 yAxis = 0, 100, 6 xBins = temp_table_p21, coolant, readonly yBins = asePctTable2 gauge = cltGauge curve = aseTaper2, "Afterstart Enrichment (ASE) Taper 2" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#aset2" columnLabel = "Coolant", "Taper" xAxis = -40, {clthighlim}, 9 yAxis = 0, 500, 6 xBins = temp_table_p21, coolant, readonly yBins = aseCntTable2 gauge = cltGauge curve = warmup_curve2, "Warmup Enrichment (WUE) Curve 2" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#wue2" columnLabel = "Coolant", "WUE %" xAxis = -40, {clthighlim}, 9 yAxis = 0, 500, 6 xBins = temp_table_p21, coolant, readonly yBins = wueBins2 gauge = cltGauge curve = MAFtable1f, "MAF Flow Curve" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#mafflow" columnLabel = "MAF Freq", "Flow" xAxis = {maf_freq0}, {maf_freq1}, 11 yAxis = {-81 * (maf_range + 1)}, {573 * (maf_range + 1)}, 11 xBins = maff, maf_freq yBins = mafflow gauge = maf_voltsGauge curve = MAFtable1, "MAF Flow Curve" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#mafflow" columnLabel = "MAF Volts", "Flow" xAxis = 0, 5, 11 yAxis = {-81 * (maf_range + 1)}, {573 * (maf_range + 1)}, 11 xBins = mafv, maf_volts yBins = mafflow gauge = maf_voltsGauge curve = MAFtable1old, "MAF Correction Table (Old)" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#mafcor" columnLabel = "MAF Flow", "Correction" xAxis = 0, 300, 11 yAxis = 0, 255, 11 xBins = MAFFlow, maf yBins = MAFCor gauge = mafGauge curve = dwellrpm_curve, "Dwell vs RPM" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#dwellvsrpm" columnLabel = "RPM", "Dwell" xAxis = 0, {rpmhigh}, 6 yAxis = 0, 6, 6 xBins = dwellrpm_rpm yBins = dwellrpm_dwell curve = boostvss_duty_curve, "Boost Duty vs Speed" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#boostspeed" columnLabel = "Speed", "Duty" xAxis = 0, { prefSpeedUnits == 0 ? 200 : 300 }, 6 yAxis = 0, 100, 6 xBins = boostvss_speed yBins = boostvss_duty curve = boostvss_target_curve, "Boost Target vs Speed" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#boostspeed" columnLabel = "Speed", "kPa" xAxis = 0, { prefSpeedUnits == 0 ? 200 : 300 }, 6 yAxis = 0, 400, 6 xBins = boostvss_speed yBins = boostvss_target ; nitrous 1 vs time curve = n2o1_duty_time, "Nitrous1 - Duty vs Time" columnLabel = "s", "Duty" xAxis = 0, 15, 6 yAxis = 0, 100, 6 xBins = n2o1_time yBins = n2o1_duty curve = n2o1_pw_time, "Nitrous1 - Added Fuel vs Time" columnLabel = "s", "pw" xAxis = 0, 15, 6 yAxis = -5, 20, 6 xBins = n2o1_time yBins = n2o1_pw curve = n2o1_retard_time, "Nitrous1 - Retard vs Time" columnLabel = "s", "Retard" xAxis = 0, 15, 6 yAxis = 0, 30, 7 xBins = n2o1_time yBins = n2o1_retard ; nitrous 2 vs time curve = n2o2_duty_time, "Nitrous2 - Duty vs Time" columnLabel = "s", "Duty" xAxis = 0, 15, 6 yAxis = 0, 100, 6 xBins = n2o2_time yBins = n2o2_duty curve = n2o2_pw_time, "Nitrous2 - Added Fuel vs Time" columnLabel = "s", "pw" xAxis = 0, 15, 6 yAxis = -5, 20, 6 xBins = n2o2_time yBins = n2o2_pw curve = n2o2_retard_time, "Nitrous2 - Retard vs Time" columnLabel = "s", "Retard" xAxis = 0, 15, 6 yAxis = 0, 30, 7 xBins = n2o2_time yBins = n2o2_retard ; nitrous 1 vs rpm curve = n2o1_duty_rpm, "Nitrous1 - Duty vs RPM" columnLabel = "RPM", "Duty" xAxis = 0, {rpmhigh}, 6 yAxis = 0, 100, 6 xBins = n2o1_rpm yBins = n2o1_duty curve = n2o1_pw_rpm, "Nitrous1 - Added fuel vs RPM" columnLabel = "RPM", "pw" xAxis = 0, {rpmhigh}, 6 yAxis = -5, 20, 6 xBins = n2o1_rpm yBins = n2o1_pw curve = n2o1_retard_rpm, "Nitrous1 - Retard vs RPM" columnLabel = "RPM", "Retard" xAxis = 0, {rpmhigh}, 6 yAxis = 0, 30, 7 xBins = n2o1_rpm yBins = n2o1_retard ; nitrous 2 vs rpm curve = n2o2_duty_rpm, "Nitrous2 - Duty vs RPM" columnLabel = "RPM", "Duty" xAxis = 0, {rpmhigh}, 6 yAxis = 0, 100, 6 xBins = n2o2_rpm yBins = n2o2_duty curve = n2o2_pw_rpm, "Nitrous2 - Added Fuel vs RPM" columnLabel = "RPM", "pw" xAxis = 0, {rpmhigh}, 6 yAxis = -5, 20, 6 xBins = n2o2_rpm yBins = n2o2_pw curve = n2o2_retard_rpm, "Nitrous2 - Retard vs RPM" columnLabel = "RPM", "Retard" xAxis = 0, {rpmhigh}, 6 yAxis = 0, 30, 7 xBins = n2o2_rpm yBins = n2o2_retard ;mat/clt curve = matclt_curve, "MAT/CLT correction" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#matcltcor" columnLabel = "flow", "%CLT" xAxis = 0, {rpmhigh * 400}, 5 yAxis = 0, 100, 5 xBins = matclt_flow, calcflow yBins = matclt_pct ;small pulsewidths curve = smallcurve0, "Small Pulsewidth Curve 1" columnLabel = "Original", "New" xAxis = 0, 2, 5 yAxis = 0, 2, 5 xBins = smallpwpw yBins = smallpw0 curve = smallcurve1, "Small Pulsewidth Curve 2" columnLabel = "Original", "New" xAxis = 0, 2, 5 yAxis = 0, 2, 5 xBins = smallpwpw yBins = smallpw1 curve = smallcurve2, "Small Pulsewidth Curve 3" columnLabel = "Original", "New" xAxis = 0, 2, 5 yAxis = 0, 2, 5 xBins = smallpwpw yBins = smallpw2 curve = smallcurve3, "Small Pulsewidth Curve 4" columnLabel = "Original", "New" xAxis = 0, 2, 5 yAxis = 0, 2, 5 xBins = smallpwpw yBins = smallpw3 curve = opencurve0, "Dead Time Voltage % Curve 1" columnLabel = "Voltage", "" xAxis = 7.2, 19.2, 7 yAxis = 0, 500, 6 xBins = opentimev, batteryVoltage yBins = opentimepct0 curve = opencurve1, "Injector Dead Time Curve 2" columnLabel = "Voltage", "" xAxis = 7.2, 19.2, 7 yAxis = 0, 500, 6 xBins = opentimev, batteryVoltage yBins = opentimepct1 curve = opencurve2, "Injector Dead Time Curve 3" columnLabel = "Voltage", "" xAxis = 7.2, 19.2, 7 yAxis = 0, 500, 6 xBins = opentimev, batteryVoltage yBins = opentimepct2 curve = opencurve3, "Injector Dead Time Curve 4" columnLabel = "Voltage", "" xAxis = 7.2, 19.2, 7 yAxis = 0, 500, 6 xBins = opentimev, batteryVoltage yBins = opentimepct3 curve = boost_timed_curve, "Boost %age After Launch" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#boostdelay" columnLabel = "Time", "" xAxis = 0, 15, 6 yAxis = 0, 100, 6 xBins = boost_timed_time yBins = boost_timed_pct curve = mapsample_curve, "MAP Sample Timing" columnLabel = "RPM", "deg" xAxis = 0, {rpmhigh}, 8 yAxis = 0, 180, 8 xBins = map_sample_rpms yBins = map_sample_timing gauge = tachometer curve = dwellSettings, "Dwell Battery Correction" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#dwellbat" columnLabel = "Voltage", "%age" xAxis = 6, 16, 6 yAxis = 0, 500, 6 xBins = dwellvolts yBins = dwellcorr curve = coldAdvance, "Cold Advance" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#coldadv" columnLabel = "Coolant", "Offset" xAxis = -40, {clthighlim}, 9 yAxis = -10, 10, 5 xBins = tempTable, coolant, readonly yBins = cold_adv_table gauge = cltGauge curve = iacBins, "Stepper Idle Warmup Position" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#idlewu" columnLabel = "Coolant", "IAC Steps" xAxis = -40, {clthighlim}, 9 yAxis = 0, 300, 7 xBins = tempTable, coolant, readonly yBins = iacstepTable gauge = cltGauge curve = ipwBins, "PWM Idle Warmup Duty Cycle" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#idlewu" columnLabel = "Coolant", "Idle PWM duty" xAxis = -40, {clthighlim}, 9 yAxis = 0, 100, 6 xBins = tempTable, coolant, readonly yBins = ipwmTable gauge = cltGauge curve = primingPW, "Priming Pulse" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#primep" columnLabel = "Coolant", "Prime PW" xAxis = -40, {clthighlim}, 9 yAxis = 0, 20, 5 xBins = temp_table_p5, coolant, readonly yBins = primePWTable gauge = cltGauge curve = crankingPW, "Cranking Pulse %" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#crankp" columnLabel = "Coolant", "Cranking PW%" xAxis = -40, {clthighlim}, 9 yAxis = 0, 500, 6 xBins = temp_table_p5, coolant yBins = crankPctTable gauge = cltGauge curve = asePct, "Afterstart Enrichment (ASE) Percentage" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#asep" columnLabel = "Coolant", "Afterstart" xAxis = -40, {clthighlim}, 9 yAxis = 0, 100, 6 xBins = temp_table_p5, coolant, readonly yBins = asePctTable gauge = cltGauge curve = aseTaper, "Afterstart Enrichment (ASE) Taper" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#aset" columnLabel = "Coolant", "Taper" xAxis = -40, {clthighlim}, 9 yAxis = 0, 500, 6 xBins = temp_table_p5, coolant, readonly yBins = aseCntTable gauge = cltGauge curve = matBasedRetard, "MAT-Based Timing Retard" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#matretard" columnLabel = "MAT", "Retard" xAxis = -40, {mathigh}, 9 yAxis = 0, 15, 7 xBins = matTemps, airtemp yBins = matRetard gauge = matGauge curve = barometerCorr, "Barometric Correction" columnLabel = "Barometer", "Correction" xAxis = 60, 120, 7 yAxis = 80, 120, 7 xBins = baroCorrVals, barometer yBins = baroCorrDelta gauge = barometerGauge curve = airdenCorr, "MAT Air density" columnLabel = "Air temp", "Correction" xAxis = -40, 200, 9 yAxis = 70, 130, 7 xBins = matCorrTemps2, airtemp yBins = matCorrDelta2 gauge = airtempGauge curve = manifoldTempCorr, "MAF/MAT Correction" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#mafmatcor" columnLabel = "MAT", "Correction" xAxis = -40, 200, 9 yAxis = -30, 30, 7 xBins = matCorrTemps, mat yBins = matCorrDelta gauge = matGauge ; this is just as an example.. not yet finished curve = EAEmanycurves, "Combined EAE Curve Graph - example to test TunerStudio features" columnLabel = "RPM", "Correction" xAxis = 0, {rpmhigh}, 12 yAxis = 0, 200, 12 xBins = EAESOCRPMbins, rpm yBins = EAESON xBins = EAEAWCRPMbins, rpm yBins = EAEAWN xBins = EAEAWCRPMbins2, rpm yBins = EAEAWN2 xBins = EAESOCRPMbins2, rpm ; commented out to show last yAxis tied to previous xAxis yBins = EAESON2 gauge = EAEGauge1 ; As always gauge is optional lineLabel = "Sucked-from-walls const" lineLabel = "Adhere-to-walls coef" lineLabel = "Adhere-to-walls coef 2" lineLabel = "Sucked-from-walls Correction" curve = EAEBAWCcurve, "EAE Adhere-to-walls Coefficient" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#eaeawc" columnLabel = "%", "Correction" xAxis = 0, 255, 12 yAxis = 0, 100, 12 xBins = EAEAWCKPAbins, eaeload1 yBins = EAEBAWC gauge = EAEGauge1 curve = EAEBSOCcurve, "EAE Sucked-from-walls Coefficient" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#eaeswc" columnLabel = "%", "Correction" xAxis = 0, 255, 12 yAxis = 0, 25.5, 12 xBins = EAESOCKPAbins, eaeload1 yBins = EAEBSOC gauge = EAEGauge1 curve = EAEAWNcurve, "EAE Adhere-to-walls RPM Correction" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#eaeawrc" columnLabel = "RPM", "Correction" xAxis = 0, {rpmhigh}, 12 yAxis = 0, 200, 12 xBins = EAEAWCRPMbins, rpm yBins = EAEAWN gauge = EAEGauge1 curve = EAESONcurve, "EAE Sucked-from-walls RPM Correction" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#eaeswrc" columnLabel = "RPM", "Correction" xAxis = 0, {rpmhigh}, 12 yAxis = 0, 200, 12 xBins = EAESOCRPMbins, rpm yBins = EAESON gauge = EAEGauge1 curve = EAESOWcurve, "EAE Sucked-from-walls CLT Correction" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#eaeswcc" columnLabel = "CLT", "Correction" xAxis = 0, {clthighlim}, 12 yAxis = 0, 200, 12 xBins = EAESOWCLTbins, coolant yBins = EAESOW gauge = EAEGauge1 curve = EAEAWWcurve, "EAE Adhere-to-walls CLT Correction" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#eaeawcc" columnLabel = "CLT", "Correction" xAxis = 0, {clthighlim}, 12 yAxis = 0, 200, 12 xBins = EAEAWWCLTbins, coolant yBins = EAEAWW gauge = EAEGauge1 curve = EAEBAWCcurve2, "EAE Adhere-to-walls Coefficient 2" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#eaeawc2" columnLabel = "%", "Correction" xAxis = 0, 255, 12 yAxis = 0, 100, 12 xBins = EAEAWCKPAbins2, fuelload yBins = EAEBAWC2 gauge = EAEGauge1 curve = EAEBSOCcurve2, "EAE Sucked-from-walls Coefficient 2" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#eaeswc" columnLabel = "%", "Correction" xAxis = 0, 255, 12 yAxis = 0, 25.5, 12 xBins = EAESOCKPAbins2, fuelload yBins = EAEBSOC2 gauge = EAEGauge1 curve = EAEAWNcurve2, "EAE Adhere-to-walls RPM Correction 2" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#eaeawrc2" columnLabel = "RPM", "Correction" xAxis = 0, {rpmhigh}, 12 yAxis = 0, 200, 12 xBins = EAEAWCRPMbins2, rpm yBins = EAEAWN2 gauge = EAEGauge1 curve = EAESONcurve2, "EAE Sucked-from-walls RPM Correction 2" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#eaeswrc2" columnLabel = "RPM", "Correction" xAxis = 0, {rpmhigh}, 12 yAxis = 0, 200, 12 xBins = EAESOCRPMbins2, rpm yBins = EAESON2 gauge = EAEGauge1 curve = EAESOWcurve2, "EAE Sucked-from-walls CLT Correction 2" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#eaeswcc2" columnLabel = "CLT", "Correction" xAxis = 0, {clthighlim}, 12 yAxis = 0, 200, 12 xBins = EAESOWCLTbins2, coolant yBins = EAESOW2 gauge = EAEGauge1 curve = EAEAWWcurve2, "EAE Adhere-to-walls CLT Correction 2" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#eaeawcc2" columnLabel = "CLT", "Correction" xAxis = 0, {clthighlim}, 12 yAxis = 0, 200, 12 xBins = EAEAWWCLTbins2, coolant yBins = EAEAWW2 gauge = EAEGauge1 curve = XAccTable, "X Accel Fuel Correction" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#xtpuddlea" columnLabel = "RPM", "Correction" xAxis = 0, {rpmhigh}, 4 yAxis = 0, 120, 4 xBins = XTrpms, rpm yBins = XAcc gauge = EAEGauge1 curve = XDecTable, "X Decel Fuel Correction" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#xtpuddled" columnLabel = "RPM", "Correction" xAxis = 0, {rpmhigh}, 9 yAxis = 0, 120, 9 xBins = XTrpms, rpm yBins = XDec gauge = EAEGauge1 curve = TauAccTable, "Tau Accel Fuel Correction" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#xttimea" columnLabel = "RPM", "time" xAxis = 0, {rpmhigh}, 9 yAxis = 0, 1000, 9 xBins = XTrpms, rpm yBins = TauAcc gauge = EAEGauge1 curve = TauDecTable, "Tau Decel Correction" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#xttimed" columnLabel = "RPM", "time" xAxis = 0, {rpmhigh}, 9 yAxis = 0, 1000, 9 xBins = XTrpms, rpm yBins = TauDec gauge = EAEGauge1 curve = XCltTable, "X (Puddling) Temp. Correction Factors" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#xtxtemp" columnLabel = "Temperature", "Correction" xAxis = -40, {clthighlim}, 9 yAxis = 0, 600, 9 xBins = XClt_temps yBins = XClt gauge = cltGauge curve = TCltTable, "Tau (Time) Temp. Correction Factors" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#xtttemp" columnLabel = "Temperature", "time" xAxis = -40, {clthighlim}, 9 yAxis = 0, 600, 9 xBins = TauClt_temps yBins = TauClt gauge = cltGauge curve = NoiseFiltercurve, "Noise Filter Curve" columnLabel = "RPMS", "usec" xAxis = 0, {rpmhigh}, 4 yAxis = 0, 2000, 4 xBins = NoiseFilterRpm yBins = NoiseFilterLen curve = warmup_curve, "Warmup Enrichment (WUE) Curve" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#wue" columnLabel = "Coolant", "WUE %" xAxis = -40, {clthighlim}, 9 yAxis = 0, 500, 6 xBins = tempTable, coolant yBins = wueBins gauge = cltGauge curve = idleAdvance_curve, "Idle Advance Timing" columnLabel = "Load %", "deg" xAxis = 0, 100, 4 yAxis = -10, 90, 4 xBins = idleadvance_loads, fuelload yBins = idleadvance_curve curve = pwmidle_target_curve, "Closed-Loop Idle Target RPMs" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#clidletarg" columnLabel = "CLT", "RPM" xAxis = 0, {clthighlim}, 8 yAxis = 0, 2000, 8 xBins = pwmidle_clt_temps, coolant yBins = pwmidle_target_rpms curve = revlimiterBins, "Coolant Based Rev Limit" columnLabel = "Coolant", "Rev limit" xAxis = -40, {clthighlim}, 8 yAxis = 0, 15000, 8 xBins = RevLimLookup, coolant yBins = RevLimRpm1 gauge = cltGauge curve = pwmidle_crank_dutyorsteps_dutycurve, "Coolant-Based Crank Duty" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#idlecrank" columnLabel = "Coolant", "Duty %" xAxis = -40, {clthighlim}, 4 yAxis = 0, 100, 4 xBins = pwmidle_crank_clt_temps, coolant yBins = pwmidle_crank_dutyorsteps_duty gauge = cltGauge curve = pwmidle_crank_dutyorsteps_stepscurve, "Coolant-Based Crank Steps" topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#idlecrank" columnLabel = "Coolant", "Steps" xAxis = -40, {clthighlim}, 4 yAxis = 0, 512, 4 xBins = pwmidle_crank_clt_temps, coolant yBins = pwmidle_crank_dutyorsteps_steps gauge = cltGauge curve = ITB_load_loadvals_curve, "ITB Load at TPS Switchpoint" columnLabel = "RPM", "Load" xAxis = 0, {rpmhigh}, 12 yAxis = 0, 100, 12 xBins = ITB_load_rpms, rpm yBins = ITB_load_loadvals curve = ITB_load_switchpoint_curve, "ITB Load TPS Switchpoints" columnLabel = "RPM", "TPS %" xAxis = 0, {rpmhigh}, 12 yAxis = 0, 100, 12 xBins = ITB_load_rpms, rpm yBins = ITB_load_switchpoints [TableEditor] ; table_id, map3d_id, "title", page table = dwell_tbl, dwell_tblMap, "Dwell Table", 1 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#dwelltable" xBins = dwell_table_rpms, rpm yBins = dwell_table_loads, ignload zBins = dwell_table_values upDownLabel = "UP", "DOWN" gridOrient = 250, 0, 340 table = ego_delay_Tbl, ego_delay_Map, "EGO Delay Table", 1 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#egodelay" xBins = ego_delay_rpms, rpm yBins = ego_delay_loads, afrload1 zBins = ego_delay_table upDownLabel = "SHORTER", "LONGER" gridOrient = 250, 0, 340 table = ego_auth_Tbl, ego_auth_Map, "EGO Authority Table", 1 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#egoauth" xBins = ego_auth_rpms, rpm yBins = ego_auth_loads, afrload1 zBins = ego_auth_table upDownLabel = "LEANER", "RICHER" gridOrient = 250, 0, 340 table = ltt_Table1Tbl, ltt_Table1Map, "Long Term Trim Table 1", 15 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#ltttable" xBins = ltt_rpms, rpm yBins = ltt_loads, fuelload zBins = ltt_table1 upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 table = fp_dutyTbl, fp_dutyMap, "Fuel Pump Duty Table", 1 ; constant, variable xBins = fpd_rpm rpm yBins = fpd_load, fuelload zBins = fpd_duty upDownLabel = "MORE", "LESS" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = alphaMAPTbl, alphaMAPMap, "Fallback MAP Table", 1 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#fallbackmap" xBins = amap_rpm, rpm yBins = amap_tps, tps zBins = alphaMAPtable upDownLabel = "UP", "DOWN" gridOrient = 250, 0, 340 table = pwmidle_cl_initialvalues_dty, pwmidle_cl_initialvalues_dtymap, "Closed-Loop Idle Initial Values", 19 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#clidleinit" xBins = pwmidle_cl_initialvalue_rpms, cl_idle_targ_rpm yBins = pwmidle_cl_initialvalue_matorclt, pwmidle_cl_initialvalue_matorclt_follower zBins = pwmidle_cl_initialvalues_duties upDownLabel = "INCREASE","DECREASE" gridOrient = 250, 0, 340 table = pwmidle_cl_initialvalues_stps, pwmidle_cl_initialvalues_stpmap, "Closed-Loop Idle Initial Values", 19 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#clidleinit" xBins = pwmidle_cl_initialvalue_rpms, cl_idle_targ_rpm yBins = pwmidle_cl_initialvalue_matorclt, pwmidle_cl_initialvalue_matorclt_follower zBins = pwmidle_cl_initialvalues_steps upDownLabel = "INCREASE","DECREASE" gridOrient = 250, 0, 340 ;vvt timing table = vvt_timing1_tbl, vvt_timing1_map, "VVT Intake (Relative Timing)", 7 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#vvtint" xBins = vvt_timing_rpm, rpm yBins = vvt_timing_load, vvt_load zBins = vvt_timing1 upDownLabel = "ADVANCE", "RETARD" gridOrient = 250, 0, 340 table = vvt_timing2_tbl, vvt_timing2_map, "VVT Exhaust (Relative Timing)", 7 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#vvtexh" xBins = vvt_timing_rpm, rpm yBins = vvt_timing_load, vvt_load zBins = vvt_timing2 upDownLabel = "ADVANCE", "RETARD" gridOrient = 250, 0, 340 table = als_rifuelcut_tbl, als_rifuelcut_map, "Turbo Anti-lag Roving Idle", 14 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#alsidle" xBins = als_rirpms, rpm yBins = als_ritpss, tps zBins = als_rifuelcut upDownLabel = "HIGHER", "LOWER" gridOrient = 250, 0, 340 table = als_fuelcut_tbl, als_fuelcut_map, "ALS Fuel Cut%", 14 xBins = als_rpms, rpm yBins = als_tpss, tps zBins = als_fuelcut upDownLabel = "HIGHER", "LOWER" gridOrient = 250, 0, 340 table = als_sparkcut_tbl, als_sparkcut_map, "ALS Spark Cut%", 14 xBins = als_rpms, rpm yBins = als_tpss, tps zBins = als_sparkcut upDownLabel = "HIGHER", "LOWER" gridOrient = 250, 0, 340 table = als_timing_tbl, als_timing_map, "ALS Timing", 14 xBins = als_rpms, rpm yBins = als_tpss, tps zBins = als_timing upDownLabel = "ADVANCE", "RETARD" gridOrient = 250, 0, 340 table = als_addfuel_tbl, als_addfuel_map, "ALS Added Fuel %age", 14 xBins = als_rpms, rpm yBins = als_tpss, tps zBins = als_addfuel upDownLabel = "HIGHER", "LOWER" gridOrient = 250, 0, 340 table = pwm_duties_Tbl_a, pwm_duties_map_a, "Generic PWM Output A", 11 xBins = pwm_rpms_a, rpm yBins = pwm_loadvals_a, pwma_load zBins = pwm_duties_a upDownLabel = "HIGHER", "LOWER" gridOrient = 250, 0, 340 table = pwm_duties_Tbl_b, pwm_duties_map_b, "Generic PWM Output B", 2 xBins = pwm_rpms_b, rpm yBins = pwm_loadvals_b, pwmb_load zBins = pwm_duties_b upDownLabel = "HIGHER", "LOWER" gridOrient = 250, 0, 340 table = pwm_duties_Tbl_c, pwm_duties_map_c, "Generic PWM Output C", 2 xBins = pwm_rpms_c, rpm yBins = pwm_loadvals_c, pwmc_load zBins = pwm_duties_c upDownLabel = "HIGHER", "LOWER" gridOrient = 250, 0, 340 table = pwm_duties_Tbl_d, pwm_duties_map_d, "Generic PWM Output D", 2 xBins = pwm_rpms_d, rpm yBins = pwm_loadvals_d, pwmd_load zBins = pwm_duties_d upDownLabel = "HIGHER", "LOWER" gridOrient = 250, 0, 340 table = pwm_duties_Tbl_vvt, pwm_duties_map_vvt, "Generic PWM Output E / VVT", 2 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#vvtonoff" xBins = pwm_rpms_e, rpm yBins = pwm_loadvals_e, vvt_load zBins = pwm_duties_e upDownLabel = "HIGHER", "LOWER" gridOrient = 250, 0, 340 table = pwm_duties_Tbl_e, pwm_duties_map_e, "Generic PWM Output E", 2 xBins = pwm_rpms_e, rpm yBins = pwm_loadvals_e, pwme_load zBins = pwm_duties_e upDownLabel = "HIGHER", "LOWER" gridOrient = 250, 0, 340 table = pwm_duties_Tbl_f, pwm_duties_map_f, "Generic PWM Output F", 2 xBins = pwm_rpms_f, rpm yBins = pwm_loadvals_f, pwmf_load zBins = pwm_duties_f upDownLabel = "HIGHER", "LOWER" gridOrient = 250, 0, 340 table = generic_pid_Tbl_a, generic_pid_map_a, "Generic Closed-Loop A", 17 xBins = generic_pid_rpms_a, rpm yBins = generic_pid_loadvals_a, generic_pid_load_a zBins = generic_pid_targets_a upDownLabel = "HIGHER", "LOWER" gridOrient = 250, 0, 340 table = generic_pid_Tbl_b, generic_pid_map_b, "Generic Closed-Loop B", 17 xBins = generic_pid_rpms_b, rpm yBins = generic_pid_loadvals_b, generic_pid_load_b zBins = generic_pid_targets_b upDownLabel = "HIGHER", "LOWER" gridOrient = 250, 0, 340 table = waterinjTbl, waterinjMap, "Water Injection Duty Table ", 1 xBins = waterinj_rpm, rpm yBins = waterinj_map, map zBins = waterinj_duty upDownLabel = "MORE", "LESS" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. #if LAMBDA table = maxafr1Tbl, maxafr1Map, "Max AFR 1 in Lambda", 1 #else table = maxafr1Tbl, maxafr1Map, "Max AFR Difference", 1 #endif xBins = maxafr1_rpm, rpm yBins = maxafr1_load, maxafrload zBins = maxafr1_diff upDownLabel = "LEANER", "RICHER" gridOrient = 250, 0, 340 table = veTable1Tbl, veTable1Map, "Fuel VE Table 1", 4 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#ve1" ; constant, variable xBins = frpm_table1, rpm yBins = fmap_table1, fuelload zBins = veTable1 upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = veTable2Tbl, veTable2Map, "Fuel VE Table 2", 4 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#ve2" xBins = frpm_table2, rpm yBins = fmap_table2, fuelload2 zBins = veTable2 upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 table = veTable3Tbl, veTable3Map, "Fuel VE Table 3", 4 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#ve3" ; constant, variable xBins = frpm_table3, rpm yBins = fmap_table3, fuelload zBins = veTable3 upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = veTable4Tbl, veTable4Map, "Fuel VE Table 4", 4 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#ve4" ; constant, variable xBins = frpm_table4, rpm yBins = fmap_table4, fuelload2 zBins = veTable4 upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = idleve1Tbl, idleve1Map, "Idle VE table", 10 xBins = idleve_rpms1, rpm yBins = idleve_loads1, fuelload zBins = idleve_table1 upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 table = idleve2Tbl, idleve2Map, "Idle VE Table - Dual Fuel", 10 xBins = idleve_rpms2, rpm yBins = idleve_loads2, fuelload zBins = idleve_table2 upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 table = stagedTable, stagedMap, "Staged Injection Table", 6 xBins = staged_rpms, rpm yBins = staged_loads, fuelload zBins = staged_percents upDownLabel = "MORE", "LESS" gridOrient = 250, 0, 340 #if LAMBDA table = afrTable1Tbl, afrTable1Map, "Lambda Table 1", 1 #else table = afrTable1Tbl, afrTable1Map, "AFR Table 1", 1 #endif topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#afr1" xBins = arpm_table1, rpm yBins = amap_table1, afrload1 zBins = afrTable1 upDownLabel = "LEANER", "RICHER" gridOrient = 250, 0, 340 #if LAMBDA table = afrTable2Tbl, afrTable2Map, "Lambda Table 2", 1 #else table = afrTable2Tbl, afrTable2Map, "AFR Table 2", 1 #endif topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#afr2" xBins = arpm_table2, rpm yBins = amap_table2, fuelload zBins = afrTable2 upDownLabel = "LEANER", "RICHER" gridOrient = 250, 0, 340 table = ignitionTbl1, ignitionMap1, "Ignition Table 1 (Spark Advance)", 3 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#ign1" xBins = srpm_table1, rpm yBins = smap_table1, ignload zBins = advanceTable1 upDownLabel = "ADVANCING", "RETARDING" gridOrient = 250, 0, 340 table = ignitionTbl2, ignitionMap2, "Ignition Table 2 (Spark Advance)", 3 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#ign2" xBins = srpm_table2, rpm yBins = smap_table2, ignload2 zBins = advanceTable2 upDownLabel = "ADVANCING", "RETARDING" gridOrient = 250, 0, 340 table = ignitionTbl3, ignitionMap3, "Ignition Table 3 (Spark Advance)", 4 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#ign3" xBins = srpm_table3, rpm yBins = smap_table3, ignload zBins = advanceTable3 upDownLabel = "ADVANCING", "RETARDING" gridOrient = 250, 0, 340 table = ignitionTbl4, ignitionMap4, "Ignition Table 4 (Spark Advance)", 4 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#ign4" xBins = srpm_table4, rpm yBins = smap_table4, ignload2 zBins = advanceTable4 upDownLabel = "ADVANCING", "RETARDING" gridOrient = 250, 0, 340 table = RotarySplitTbl, RotarySplitMap, "Rotary Split Table", 3 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#rotarysplit" xBins = RotarySplitRPM, rpm yBins = RotarySplitLoad, ignload zBins = RotarySplitTable upDownLabel = "ADVANCING", "RETARDING" gridOrient = 250, 0, 340 table = boostctlDutys, boostctlDtyMap, "Boost Control Duty 1", 2 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#boostduty" xBins = boost_ctl_pwmtarg_rpm_bins, rpm yBins = boost_ctl_pwmtarg_tps_bins, throttle zBins = boost_ctl_pwm_targets upDownLabel = "HIGHER", "LOWER" gridOrient = 250, 0, 340 table = boostctlTargs, boostctlTargMap, "Boost Control Targets 1", 2 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#boosttarg" xBins = boost_ctl_loadtarg_rpm_bins, rpm yBins = boost_ctl_loadtarg_tps_bins, throttle zBins = boost_ctl_load_targets upDownLabel = "HIGHER", "LOWER" gridOrient = 250, 0, 340 table = boostctlDutys2, boostctlDtyMap2, "Boost Control Duty 2", 2 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#boostduty2" xBins = boost_ctl_pwmtarg_rpm_bins2, rpm yBins = boost_ctl_pwmtarg_tps_bins2, throttle zBins = boost_ctl_pwm_targets2 upDownLabel = "HIGHER", "LOWER" gridOrient = 250, 0, 340 table = boostctlCLPWMtargs1, boostctlCLPWMtargsMap1, "Boost Control Initial Duty 1", 15 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#boostinit" xBins = boost_ctl_cl_pwm_rpms1, rpm yBins = boost_ctl_cl_pwm_targboosts1, boost_targ_1 zBins = boost_ctl_cl_pwm_targs1 upDownLabel = "HIGHER", "LOWER" gridOrient = 250, 0, 340 table = boostctlCLPWMtargs2, boostctlCLPWMtargsMap2, "Boost Control Initial Duty 2", 15 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#boostinit2" xBins = boost_ctl_cl_pwm_rpms2, rpm yBins = boost_ctl_cl_pwm_targboosts2, boost_targ_2 zBins = boost_ctl_cl_pwm_targs2 upDownLabel = "HIGHER", "LOWER" gridOrient = 250, 0, 340 table = boostctlTargs2, boostctlTargMap2, "Boost Control Targets 2", 2 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#boosttarg2" xBins = boost_ctl_loadtarg_rpm_bins2, rpm yBins = boost_ctl_loadtarg_tps_bins2, throttle zBins = boost_ctl_load_targets2 upDownLabel = "HIGHER", "LOWER" gridOrient = 250, 0, 340 ;injector trims table = inj_trimaTbl, inj_trimaMap, "Cyl 1 Fuel Trim", 7 ; constant, variable xBins = inj_trim_rpm, rpm yBins = inj_trim_load, fuelload zBins = inj_trima upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = inj_trimbTbl, inj_trimbMap, "Cyl 2 Fuel Trim", 7 ; constant, variable xBins = inj_trim_rpm, rpm, readonly yBins = inj_trim_load, fuelload, readonly zBins = inj_trimb upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = inj_trimcTbl, inj_trimcMap, "Cyl 3 Fuel Trim", 7 ; constant, variable xBins = inj_trim_rpm, rpm, readonly yBins = inj_trim_load, fuelload, readonly zBins = inj_trimc upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = inj_trimdTbl, inj_trimdMap, "Cyl 4 Fuel Trim", 7 ; constant, variable xBins = inj_trim_rpm, rpm, readonly yBins = inj_trim_load, fuelload, readonly zBins = inj_trimd upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = inj_trimeTbl, inj_trimeMap, "Cyl 5 Fuel Trim", 7 ; constant, variable xBins = inj_trim_rpm, rpm, readonly yBins = inj_trim_load, fuelload, readonly zBins = inj_trime upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = inj_trimfTbl, inj_trimfMap, "Cyl 6 Fuel Trim", 7 ; constant, variable xBins = inj_trim_rpm, rpm, readonly yBins = inj_trim_load, fuelload, readonly zBins = inj_trimf upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = inj_trimgTbl, inj_trimgMap, "Cyl 7 Fuel Trim", 7 ; constant, variable xBins = inj_trim_rpm, rpm, readonly yBins = inj_trim_load, fuelload, readonly zBins = inj_trimg upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = inj_trimhTbl, inj_trimhMap, "Cyl 8 Fuel Trim", 7 ; constant, variable xBins = inj_trim_rpm, rpm, readonly yBins = inj_trim_load, fuelload, readonly zBins = inj_trimh upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = inj_trim1Tbl, inj_trim1Map, "Injector Trim 1", 7 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#injtrim1" ; constant, variable xBins = inj_trim_rpm, rpm, readonly yBins = inj_trim_load, fuelload, readonly zBins = inj_trimi upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = inj_trim2Tbl, inj_trim2Map, "Injector Trim 2", 7 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#injtrim2" ; constant, variable xBins = inj_trim_rpm, rpm, readonly yBins = inj_trim_load, fuelload, readonly zBins = inj_trimj upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = inj_trimiTbl, inj_trimiMap, "Cyl 9 Fuel Trim", 7 ; constant, variable xBins = inj_trim_rpm, rpm yBins = inj_trim_load, fuelload zBins = inj_trimi upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = inj_trimjTbl, inj_trimjMap, "Cyl 10 Fuel Trim", 7 ; constant, variable xBins = inj_trim_rpm, rpm, readonly yBins = inj_trim_load, fuelload, readonly zBins = inj_trimj upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = inj_trimkTbl, inj_trimkMap, "Cyl 11 Fuel Trim", 7 ; constant, variable xBins = inj_trim_rpm, rpm, readonly yBins = inj_trim_load, fuelload, readonly zBins = inj_trimk upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = inj_trimlTbl, inj_trimlMap, "Cyl 12 Fuel Trim", 7 ; constant, variable xBins = inj_trim_rpm, rpm, readonly yBins = inj_trim_load, fuelload, readonly zBins = inj_triml upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = inj_trimmTbl, inj_trimmMap, "Cyl 13 Fuel Trim", 7 ; constant, variable xBins = inj_trim_rpm, rpm, readonly yBins = inj_trim_load, fuelload, readonly zBins = inj_trimm upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = inj_trimnTbl, inj_trimnMap, "Cyl 14 Fuel Trim", 7 ; constant, variable xBins = inj_trim_rpm, rpm, readonly yBins = inj_trim_load, fuelload, readonly zBins = inj_trimn upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = inj_trimoTbl, inj_trimoMap, "Cyl 15 Fuel Trim", 7 ; constant, variable xBins = inj_trim_rpm, rpm, readonly yBins = inj_trim_load, fuelload, readonly zBins = inj_trimo upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = inj_trimpTbl, inj_trimpMap, "Cyl 16 Fuel Trim", 7 ; constant, variable xBins = inj_trim_rpm, rpm, readonly yBins = inj_trim_load, fuelload, readonly zBins = inj_trimp upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. ;inj timing table = inj_timing_tbl, inj_timing_map, "Injector Timing", 7 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#injt1" xBins = inj_timing_rpm, rpm yBins = inj_timing_load, fuelload zBins = inj_timing upDownLabel = "ADVANCE", "RETARD" gridOrient = 250, 0, 340 table = inj_timing_sec_tbl, inj_timing_sec_map, "Secondary Injector Timing", 7 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#injt2" xBins = inj_timing_sec_rpm, rpm yBins = inj_timing_sec_load, fuelload zBins = inj_timing_sec upDownLabel = "ADVANCE", "RETARD" gridOrient = 250, 0, 340 ;spark trims table = spk_trimaTbl, spk_trimaMap, "Spark Trim 1", 8 ; constant, variable xBins = spk_trim_rpm, rpm yBins = spk_trim_load, ignload zBins = spk_trima upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = spk_trimbTbl, spk_trimbMap, "Spark Trim 2", 8 ; constant, variable xBins = spk_trim_rpm, rpm yBins = spk_trim_load, ignload zBins = spk_trimb upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = spk_trimcTbl, spk_trimcMap, "Spark Trim 3", 8 ; constant, variable xBins = spk_trim_rpm, rpm yBins = spk_trim_load, ignload zBins = spk_trimc upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = spk_trimdTbl, spk_trimdMap, "Spark Trim 4", 8 ; constant, variable xBins = spk_trim_rpm, rpm yBins = spk_trim_load, ignload zBins = spk_trimd upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = spk_trimeTbl, spk_trimeMap, "Spark Trim 5", 8 ; constant, variable xBins = spk_trim_rpm, rpm yBins = spk_trim_load, ignload zBins = spk_trime upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = spk_trimfTbl, spk_trimfMap, "Spark Trim 6", 8 ; constant, variable xBins = spk_trim_rpm, rpm yBins = spk_trim_load, ignload zBins = spk_trimf upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = spk_trimgTbl, spk_trimgMap, "Spark Trim 7", 8 ; constant, variable xBins = spk_trim_rpm, rpm yBins = spk_trim_load, ignload zBins = spk_trimg upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = spk_trimhTbl, spk_trimhMap, "Spark Trim 8", 8 ; constant, variable xBins = spk_trim_rpm, rpm yBins = spk_trim_load, ignload zBins = spk_trimh upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = spk_trimiTbl, spk_trimiMap, "Spark Trim 9", 8 ; constant, variable xBins = spk_trim_rpm, rpm yBins = spk_trim_load, ignload zBins = spk_trimi upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = spk_trimjTbl, spk_trimjMap, "Spark Trim 10", 8 ; constant, variable xBins = spk_trim_rpm, rpm yBins = spk_trim_load, ignload zBins = spk_trimj upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = spk_trimkTbl, spk_trimkMap, "Spark Trim 11", 8 ; constant, variable xBins = spk_trim_rpm, rpm yBins = spk_trim_load, ignload zBins = spk_trimk upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = spk_trimlTbl, spk_trimlMap, "Spark Trim 12", 8 ; constant, variable xBins = spk_trim_rpm, rpm yBins = spk_trim_load, ignload zBins = spk_triml upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = spk_trimmTbl, spk_trimmMap, "Spark Trim 13", 8 ; constant, variable xBins = spk_trim_rpm, rpm yBins = spk_trim_load, ignload zBins = spk_trimm upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = spk_trimnTbl, spk_trimnMap, "Spark Trim 14", 8 ; constant, variable xBins = spk_trim_rpm, rpm yBins = spk_trim_load, ignload zBins = spk_trimn upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = spk_trimoTbl, spk_trimoMap, "Spark Trim 15", 8 ; constant, variable xBins = spk_trim_rpm, rpm yBins = spk_trim_load, ignload zBins = spk_trimo upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = spk_trimpTbl, spk_trimpMap, "Spark Trim 16", 8 ; constant, variable xBins = spk_trim_rpm, rpm yBins = spk_trim_load, ignload zBins = spk_trimp upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = narrowband_tgts_tbl, narrowband_tgts_map, "Narrowband EGO targets", 14 topicHelp = "file://$getProjectsDirPath()/docs/Megasquirt3_TunerStudio_MS_Lite_Reference-1.3.pdf#narrowtargs" xBins = narrowband_tgts_rpms, rpm yBins = narrowband_tgts_loads, afrload1 zBins = narrowband_tgts upDownLabel = "RICHER", "LEANER" gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. ;------------------------------------------------------------------------------- [GaugeConfigurations] ;------------------------------------------------------------------------------- ; Define a gauge's characteristics here, then go to a specific layout ; block (Tuning or FrontPage) and use the name you've defined here to ; display that gauge in a particular position. ; ; Name = Case-sensitive, user-defined name for this gauge configuration. ; Var = Case-sensitive name of variable to be displayed, see the ; OutputChannels block in this file for possible values. ; Title = Title displayed at the top of the gauge. ; Units = Units displayed below value on gauge. ; Lo = Lower scale limit of gauge. ; Hi = Upper scale limit of gauge. ; LoD = Lower limit at which danger color is used for gauge background. ; LoW = Lower limit at which warning color is used. ; HiW = Upper limit at which warning color is used. ; HiD = Upper limit at which danger color is used. ; vd = Decimal places in displayed value ; ld = Label decimal places for display of Lo and Hi, above. ;Name Var Title Units Lo Hi LoD LoW HiW HiD vd ld gaugeCategory = "Outputs 1" pulseWidth1Gauge = pulseWidth1, "Pulse Width 1", "ms", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 pulseWidth2Gauge = pulseWidth2, "Pulse Width 2", "ms", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 pulseWidthSeq1Gauge = pwseq1, "Pulse Width Seq 1", "ms", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 pulseWidthSeq2Gauge = pwseq2, "Pulse Width Seq 2", "ms", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 pulseWidthSeq3Gauge = pwseq3, "Pulse Width Seq 3", "ms", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 pulseWidthSeq4Gauge = pwseq4, "Pulse Width Seq 4", "ms", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 pulseWidthSeq5Gauge = pwseq5, "Pulse Width Seq 5", "ms", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 pulseWidthSeq6Gauge = pwseq6, "Pulse Width Seq 6", "ms", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 pulseWidthSeq7Gauge = pwseq7, "Pulse Width Seq 7", "ms", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 pulseWidthSeq8Gauge = pwseq8, "Pulse Width Seq 8", "ms", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 #if CYL_12_16_SUPPORT pulseWidthSeq9Gauge = pwseq9, "Pulse Width Seq 9", "ms", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 pulseWidthSeq10Gauge = pwseq10, "Pulse Width Seq 10", "ms", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 pulseWidthSeq11Gauge = pwseq11, "Pulse Width Seq 11", "ms", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 pulseWidthSeq12Gauge = pwseq12, "Pulse Width Seq 12", "ms", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 pulseWidthSeq13Gauge = pwseq13, "Pulse Width Seq 13", "ms", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 pulseWidthSeq14Gauge = pwseq14, "Pulse Width Seq 14", "ms", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 pulseWidthSeq15Gauge = pwseq15, "Pulse Width Seq 15", "ms", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 pulseWidthSeq16Gauge = pwseq16, "Pulse Width Seq 16", "ms", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 #else pulseWidthSeq9Gauge = pwseq9, "Pulse Width V3 inj1", "ms", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 pulseWidthSeq10Gauge = pwseq10, "Pulse Width V3 inj2", "ms", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 #endif gaugeCategory = "Outputs 2" IACgauge = iacstep, "Idle Stepper position", "steps", 0, 255, -1, -1, 999, 999, 0, 0 dwellGauge = dwell, "Dwell", "ms", 0, 10, 0.5, 1.0, 6.0, 8.0, 1, 1 dwelltrlGauge = dwell_trl, "Dwell (Trailing)", "ms", 0, 10, 0.5, 1.0, 6.0, 8.0, 1, 1 ; IAC step == idle pwm, when using pwm idle control. PWMIdlegauge = idleDC, "Idle PWM%", "%", 0, 100, -1, -1, 999, 90, 1, 1 advdegGauge = advance, "Ignition Advance", "degrees", 0, 50, -1, -1, 999, 999, 1, 1 dutyCycle1Gauge = dutyCycle1, "Duty Cycle 1", "%", 0, 100, -1, -1, 85, 90, 1, 1 dutyCycle2Gauge = dutyCycle2, "Duty Cycle 2", "%", 0, 100, -1, -1, 85, 90, 1, 1 boostdutyGauge = boostduty, "Boost Duty", "%", 0, 100, -1, -1, 100, 100, 1, 1 boostdutyGauge2 = boostduty2, "Boost Duty 2", "%", 0, 100, -1, -1, 100, 100, 1, 1 injtimingpriGauge = inj_timing_pri, "Injector timing (pri)", "degrees", 0, 50, -1, -1, 999, 999, 1, 1 injtimingsecGauge = inj_timing_sec, "Injector timing (sec)", "degrees", 0, 50, -1, -1, 999, 999, 1, 1 gaugeCategory = "Outputs 3" nitrous1_duty = nitrous1_duty, "Nitrous 1 Duty", "%", 0, 100, 100, 100, 100, 100, 0 ,0 nitrous2_duty = nitrous2_duty, "Nitrous 2 Duty", "%", 0, 100, 100, 100, 100, 100, 0 ,0 water_duty = water_duty, "Water Duty", "%", 0, 100, 100, 100, 100, 100, 0 ,0 duty_pwm_a = duty_pwm_a, "Generic PWM A Duty", "%", 0, 100, 100, 100, 100, 100, 0 ,0 duty_pwm_b = duty_pwm_b, "Generic PWM B Duty", "%", 0, 100, 100, 100, 100, 100, 0 ,0 duty_pwm_c = duty_pwm_c, "Generic PWM C Duty", "%", 0, 100, 100, 100, 100, 100, 0 ,0 duty_pwm_d = duty_pwm_d, "Generic PWM D Duty", "%", 0, 100, 100, 100, 100, 100, 0 ,0 duty_pwm_e = duty_pwm_e, "Generic PWM E Duty", "%", 0, 100, 100, 100, 100, 100, 0 ,0 duty_pwm_f = duty_pwm_f, "Generic PWM F Duty", "%", 0, 100, 100, 100, 100, 100, 0 ,0 vvt_duty1 = vvt_duty1, "VVT 1 duty", "%", 0, 100, 100, 100, 100, 100, 1 ,1 vvt_duty2 = vvt_duty2, "VVT 2 duty", "%", 0, 100, 100, 100, 100, 100, 1 ,1 vvt_duty3 = vvt_duty3, "VVT 3 duty", "%", 0, 100, 100, 100, 100, 100, 1 ,1 vvt_duty4 = vvt_duty4, "VVT 4 duty", "%", 0, 100, 100, 100, 100, 100, 1 ,1 fp_duty = fp_duty, "Fuel pump duty", "%", 0, 100, 100, 100, 100, 100, 1, 1 alt_duty = alt_duty, "Alternator Control Duty", "%", 0, 100, 100, 100, 100, 100, 0, 0 alt_freq = alt_freq, "Alternator Control Frequency", "Hz", 0, 255, 255, 255, 255, 255, 0, 0 alt_targv = alt_targv, "Alternator Target Volts", "V", 0, 16, 16, 16, 16, 16, 1, 1 generic_pid_duty_a = generic_pid_duty_a, "Generic Closed-Loop A Duty", "%", 0, 100, 100, 100, 100, 100, 1, 1 generic_pid_duty_b = generic_pid_duty_b, "Generic Closed-Loop B Duty", "%", 0, 100, 100, 100, 100, 100, 1, 1 gaugeCategory = "Calculations 1" accelEnrichGauge = accDecEnrich, "Accel Enrich%", "%", 50, 150, -1, -1, 999, 999, 0, 0 accEnrichMSGauge = accEnrichMS, "Accel Enrich PW", "ms", 50, 150, -1, -1, 999, 999, 3, 3 gammaEnrichGauge = gammaEnrich, "Total cor", "%", 50, 150, -1, -1, 151, 151, 1, 1 gammaairGauge = airCorrection, "Air density Correction", "%", 50, 150, -1, -1, 151, 151, 1, 1 warmupgauge = warmupEnrich, "Warmup Enrichment", "%", 50, 150, -1, -1, 151, 151, 1, 1 barocorgauge = baroCorrection, "Barometric Correction", "%", 50, 150, -1, -1, 151, 151, 1, 1 WFGauge1 = wallfuel1, "Fuel on the walls 1", "", 0, 40000000, 0, 0, 40000000, 40000000, 0, 0 WFGauge2 = wallfuel2, "Fuel on the walls 2", "", 0, 40000000, 0, 0, 40000000, 40000000, 0, 0 EAEGauge1 = EAEFuelCorr1, "EAE Fuel Correction 1", "%", 0, 200, 40, 70, 130, 160, 0, 0 EAEGauge2 = EAEFuelCorr2, "EAE Fuel Correction 2", "%", 0, 200, 40, 70, 130, 160, 0, 0 fuelcorr = fuelCorrection,"E85 Fuel Correction", "%", 100, 200, 99, 99, 164, 170, 0, 0 fueltemp_cor = fueltemp_cor, "Fuel Temperature Correction", "%", -100, 100, -100, -100, 100, 100, 1, 1 fuelpress_cor = fuelpress_cor, "Fuel Pressure Correction", "%", -100, 100, -100, -100, 100, 100, 1, 1 ltt_cor = ltt_cor, "Long Term Trim Correction", "%", -12.7, 12.7, -12.7, -12.7, 12.7, 12.7, 1, 1 veGauge1 = veCurr1, "VE1 Current", "%", 0, 120, -1, -1, 999, 999, 1, 1 veGauge2 = veCurr2, "VE2 Current", "%", 0, 120, -1, -1, 999, 999, 1, 1 nitrous_addfuel = n2o_addfuel, "Nitrous added fuel", "ms", -5, 20, 20, 20, 20, 20, 3, 3 tps_accel = tps_accel, "tps_accel", "%/sec", -15000, 15000, 65535, 65535, 65535, 65535, 0, 0 map_accel = map_accel, "map_accel", "kPa/sec", -15000, 15000, 65535, 65535, 65535, 65535, 0, 0 total_accel = total_accel, "total_accel", "%/sec", -15000, 15000, 65535, 65535, 65535, 65535, 0, 0 als_addfuel = als_addfuel, "ALS added fuel", "ms", -5, 20, 20, 20, 20, 20, 3, 3 reqfuelGauge = reqfuel, "Req Fuel (calc)", "ms", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 deadtime1Gauge = deadtime1, "DeadTime 1", "ms", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 gaugeCategory = "Calculations 2" knockGauge = knockRetard, "Knock Retard", "deg", 0, 25.0, -1, -1, 5.0, 10.0, 1, 1 coldAdvGauge = coldAdvDeg, "Cold advance", "deg", 0, 25.0, -50, -50, 50.0, 50.0, 1, 1 tc_retardGauge = tc_retard, "Traction Retard", "deg", 0, 25.0, -50, -50, 50.0, 50.0, 1, 1 cel_retardGauge = cel_retard, "CEL Retard", "deg", 0, 25.0, -50, -50, 50.0, 50.0, 1, 1 fc_retardGauge = fc_retard, "Fuel cut Retard", "deg", 0, 25.0, -50, -50, 50.0, 50.0, 1, 1 ext_advanceGauge = ext_advance, "External Advance", "deg", 0, 25.0, -50, -50, 50.0, 50.0, 1, 1 base_advanceGauge = base_advance, "Base Spark Advance", "deg", 0, 25.0, -50, -50, 50.0, 50.0, 1, 1 idle_cor_advanceGauge = idle_cor_advance, "Idle Correction Advance", "deg", 0, 25.0, -50, -50, 50.0, 50.0, 1, 1 mat_retardGauge = mat_retard, "MAT Retard", "deg", 0, 25.0, -50, -50, 50.0, 50.0, 1, 1 flex_advanceGauge = flex_advance, "Flex Advance", "deg", 0, 25.0, -50, -50, 50.0, 50.0, 1, 1 adv1Gauge = adv1, "Spark Table 1", "deg", 0, 25.0, -50, -50, 50.0, 50.0, 1, 1 adv2Gauge = adv2, "Spark Table 2", "deg", 0, 25.0, -50, -50, 50.0, 50.0, 1, 1 adv3Gauge = adv3, "Spark Table 3", "deg", 0, 25.0, -50, -50, 50.0, 50.0, 1, 1 adv4Gauge = adv4, "Spark Table 4", "deg", 0, 25.0, -50, -50, 50.0, 50.0, 1, 1 revlim_retardGauge= revlim_retard, "Revlim Retard", "deg", 0, 25.0, -50, -50, 50.0, 50.0, 1, 1 als_timingGauge = als_timing, "ALS Timing", "deg", 0, 25.0, -50, -50, 50.0, 50.0, 1, 1 launch_timingGauge = launch_timing, "Launch Timing", "deg", 0, 25.0, -50, -50, 50.0, 50.0, 1, 1 step3_timingGauge = step3_timing, "3-step Timing", "deg", 0, 25.0, -50, -50, 50.0, 50.0, 1, 1 launchvss_retardGauge = launchvss_retard, "Launch VSS Retard", "deg", 0, 25.0, -50, -50, 50.0, 50.0, 1, 1 timingerrGauge = timing_err, "Timing pred err", "%", -127, 127, 255,255,255,255,0,0 ; user0Gauge = user0, "User defined", "", 0, 65535, 65535, 65535, 65535, 65535, 0, 0 nitrous_retard = n2o_retard, "Nitrous retard", "deg", -5, 30, 30, 30, 30, 30, 1, 1 launch_timer = launch_timer, "Launch timer", "s", 0, 15, 15, 15, 15, 15, 3 ,3 launch_retard = launch_retard, "Launch timed retard", "deg", -5, 30, 30, 30, 30, 30, 1, 1 nitrous_timer = nitrous_timer, "Nitrous Timer", "s", 0, 15, 15, 15, 15, 15, 3 ,3 gaugeCategory = "Calculations 3" lostsyncGauge = synccnt, "Lost sync counter", "", 0, 255, 255, 255, 255, 255, 0, 0 syncreasonGauge = syncreason, "Lost sync reason", "", 0, 255, 255, 255, 255, 255, 0, 0 clockGauge = seconds, "Clock", "Seconds", 0, 65535, 10, 10, 65535, 65535, 0, 0 vss1dot = vss1dot, "VSS1 Acceleration", "ms-2", -25, 25, 65535, 65535, 65535, 65535, 0, 0 ; adjust to 50 if running top fuel vss2dot = vss2dot, "VSS2 Acceleration", "ms-2", -25, 25, 65535, 65535, 65535, 65535, 0, 0 ; adjust to 50 if running top fuel RPMdot = RPMdot, "RPMdot", "rpm/sec", -15000, 15000, 65535, 65535, 65535, 65535, 0, 0 TPSdot = TPSdot, "TPSdot", "%/sec", -15000, 15000, 65535, 65535, 65535, 65535, 0, 0 MAPdot = MAPdot, "MAPdot", "kPa/sec", -15000, 15000, 65535, 65535, 65535, 65535, 0, 0 vvttargGauge1 = vvt_target1, "VVT 1 target", "degrees", 0, 50, -1, -1, 999, 999, 1, 1 vvttargGauge2 = vvt_target2, "VVT 2 target", "degrees", 0, 50, -1, -1, 999, 999, 1, 1 vvttargGauge3 = vvt_target3, "VVT 3 target", "degrees", 0, 50, -1, -1, 999, 999, 1, 1 vvttargGauge4 = vvt_target4, "VVT 4 target", "degrees", 0, 50, -1, -1, 999, 999, 1, 1 fuelflowGauge = fuelflow, "Fuel flow (avg)", "cc/min", 0, 65535, -1, -1, 99999, 99999, 0, 0 economy_l_100km = economy_l_100km, "Fuel economy", "l/100km", 0, 300, -1, -1, 900, 900, 1, 1 economy_mpg_us = economy_mpg_us, "Fuel economy", "mpg_us", 0, 60, -1, -1, 99, 99, 0, 0 economy_mpg_uk = economy_mpg_uk, "Fuel economy", "mpg_uk", 0, 60, -1, -1, 99, 99, 0, 0 boost_target_1 = boost_targ_1, "Boost Target 1", "%", 0, 500, -1, -1, 999, 999, 1, 1 boost_target_2 = boost_targ_2, "Boost Target 2", "%", 0, 500, -1, -1, 999, 999, 1, 1 cl_idle_targ_rpm = cl_idle_targ_rpm, "CL Idle target", "RPM", 0, {rpmhigh}, 300, 600, {rpmwarn}, {rpmdang}, 0, 0 gaugeCategory = "EGT inputs" #if CELSIUS egtGauge1 = egt1, "EGT 01", "C", 0, 1250, 0, 0, 1250, 1250, 0, 0 egtGauge2 = egt2, "EGT 02", "C", 0, 1250, 0, 0, 1250, 1250, 0, 0 egtGauge3 = egt3, "EGT 03", "C", 0, 1250, 0, 0, 1250, 1250, 0, 0 egtGauge4 = egt4, "EGT 04", "C", 0, 1250, 0, 0, 1250, 1250, 0, 0 egtGauge5 = egt5, "EGT 05", "C", 0, 1250, 0, 0, 1250, 1250, 0, 0 egtGauge6 = egt6, "EGT 06", "C", 0, 1250, 0, 0, 1250, 1250, 0, 0 egtGauge7 = egt7, "EGT 07", "C", 0, 1250, 0, 0, 1250, 1250, 0, 0 egtGauge8 = egt8, "EGT 08", "C", 0, 1250, 0, 0, 1250, 1250, 0, 0 egtGauge9 = egt9, "EGT 09", "C", 0, 1250, 0, 0, 1250, 1250, 0, 0 egtGauge10 = egt10, "EGT 10", "C", 0, 1250, 0, 0, 1250, 1250, 0, 0 egtGauge11 = egt11, "EGT 11", "C", 0, 1250, 0, 0, 1250, 1250, 0, 0 egtGauge12 = egt12, "EGT 12", "C", 0, 1250, 0, 0, 1250, 1250, 0, 0 egtGauge13 = egt13, "EGT 13", "C", 0, 1250, 0, 0, 1250, 1250, 0, 0 egtGauge14 = egt14, "EGT 14", "C", 0, 1250, 0, 0, 1250, 1250, 0, 0 egtGauge15 = egt15, "EGT 15", "C", 0, 1250, 0, 0, 1250, 1250, 0, 0 egtGauge16 = egt16, "EGT 16", "C", 0, 1250, 0, 0, 1250, 1250, 0, 0 #else egtGauge1 = egt1, "EGT 01", "F", 0, 2280, 0, 0, 2280, 2280, 0, 0 egtGauge2 = egt2, "EGT 02", "F", 0, 2280, 0, 0, 2280, 2280, 0, 0 egtGauge3 = egt3, "EGT 03", "F", 0, 2280, 0, 0, 2280, 2280, 0, 0 egtGauge4 = egt4, "EGT 04", "F", 0, 2280, 0, 0, 2280, 2280, 0, 0 egtGauge5 = egt5, "EGT 05", "F", 0, 2280, 0, 0, 2280, 2280, 0, 0 egtGauge6 = egt6, "EGT 06", "F", 0, 2280, 0, 0, 2280, 2280, 0, 0 egtGauge7 = egt7, "EGT 07", "F", 0, 2280, 0, 0, 2280, 2280, 0, 0 egtGauge8 = egt8, "EGT 08", "F", 0, 2280, 0, 0, 2280, 2280, 0, 0 egtGauge9 = egt9, "EGT 09", "F", 0, 2280, 0, 0, 2280, 2280, 0, 0 egtGauge10 = egt10, "EGT 10", "F", 0, 2280, 0, 0, 2280, 2280, 0, 0 egtGauge11 = egt11, "EGT 11", "F", 0, 2280, 0, 0, 2280, 2280, 0, 0 egtGauge12 = egt12, "EGT 12", "F", 0, 2280, 0, 0, 2280, 2280, 0, 0 egtGauge13 = egt13, "EGT 13", "F", 0, 2280, 0, 0, 2280, 2280, 0, 0 egtGauge14 = egt14, "EGT 14", "F", 0, 2280, 0, 0, 2280, 2280, 0, 0 egtGauge15 = egt15, "EGT 15", "F", 0, 2280, 0, 0, 2280, 2280, 0, 0 egtGauge16 = egt16, "EGT 16", "F", 0, 2280, 0, 0, 2280, 2280, 0, 0 #endif gaugeCategory = "Sensor inputs1" #if CELSIUS cltGauge = coolant, "Coolant Temp", "°C", {cltlowlim}, {clthighlim}, -100, -100, {clthighwarn}, {clthighdang}, 0, 0 matGauge = mat, "Manifold Air Temp", "°C", -40, 110, -15, 0, 95, 100, 0, 0 airtempGauge = airtemp, "Est. Intake Air Temp", "°C", -40, 110, -15, 0, 95, 100, 0, 0 #else cltGauge = coolant, "Coolant Temp", "°F", {cltlowlim}, {clthighlim}, -100, -100, {clthighwarn}, {clthighdang}, 0, 0 matGauge = mat, "Manifold Air Temp", "°F", -40, 215, 0, 30, 200, 210, 0, 0 airtempGauge = airtemp, "Est. Intake Air Temp", "°F", -40, 215, 0, 30, 200, 210, 0, 0 #endif voltMeter = batteryVoltage,"Battery Voltage", "volts", 7, 21, 8, 9, 15, 16, 2, 2 tachometer = rpm, "Engine Speed", "RPM", 0, {rpmhigh}, 300, 600, {rpmwarn}, {rpmdang}, 0, 0 throttleGauge = throttle, "Throttle Position", "%", 0, 100, -1, 1, 90, 100, 1, 0 mapGauge = map, "Engine MAP", "kPa", 0, {loadhigh}, 0, 20, 200, {loadhigh}, 1, 0 barometerGauge = barometer, "Barometer", "kPa", 60, 120, 0, 20, 200, 245, 1, 0 fuelloadGauge = fuelload, "Fuel Load", { bitStringValue( algorithmUnits , algorithm ) }, 0, {loadhigh}, 0, 20, 200, {loadhigh}, 1, 0 fuelload2Gauge = fuelload2, "Secondary Fuel Load", { bitStringValue( algorithmUnits , algorithm2 ) }, 0, {loadhigh}, 0, 20, 200, {loadhigh}, 1, 0 ignloadGauge = ignload, "Ign Load", { bitStringValue( algorithmUnits , IgnAlgorithm ) }, 0, {loadhigh}, 0, 20, 200, {loadhigh}, 1, 0 ignload2Gauge = ignload2, "Secondary Ign Load", { bitStringValue( algorithmUnits , IgnAlgorithm2 ) }, 0, {loadhigh}, 0, 20, 200, {loadhigh}, 1, 0 eaeloadGauge = eaeload1, "EAE Load", { bitStringValue( algorithmUnits , (eaeload ? eaeload : algorithm) ) }, 0, {loadhigh}, 0, 20, 200, {loadhigh}, 1, 0 afrloadGauge = afrload1, "AFR Load", { bitStringValue( algorithmUnits , (afrload ? afrload : algorithm) ) }, 0, {loadhigh}, 0, 20, 200, {loadhigh}, 1, 0 mafGauge = maf, "Mass Air Flow", "g/sec", 0, {650 * (maf_range + 1)}, 0, {200 * (maf_range + 1)}, {480 * (maf_range + 1)}, {550 * (maf_range + 1)}, 2, 0 maf_voltsGauge = maf_volts, "MAF Volts", "V", 0, 5.00, 0, 5.00, 5.00, 5.00, 3, 1 maf_freqGauge = maf_freq, "MAF Frequency", "Hz", 0, 30000, 0, 30000, 30000, 30000, 0, 0 mafloadGauge = mafload, "MAFload", "kPa", 0, 400, -1, -1, 999, 999, 1, 0 boostbarGauge = boostbar, "Boost", "bar", -1, 3, -1, -1, 5, 5, 2, 2 boostpsigGauge = boostpsig, "Boost", "psig", -14.7, 21, -15, -15, 30, 30, 1, 1 boostvacGauge = boostvac, "Vac/Boost", "inHg/psig", -30, 30, -30, -30, 30, 30, 1, 1 knockinGauge = knock, "Knock Input", "%", 0, 100.0, -1, -1, 100.0, 100.0, 1, 1 gaugeCategory = "Sensor inputs2" stream_levelGauge = stream_level, "Stream Level", "", 0, 128, 128, 128, 128, 128, 0, 0 vehiclespeed1 = vss1, "Vehicle Speed 1", { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, 0, { prefSpeedUnits == 0 ? 200 : 300 }, 1000, 1000, 1000, 1000, 0, 0 vehiclespeed2 = vss2, "Vehicle Speed 2", { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, 0, { prefSpeedUnits == 0 ? 200 : 300 }, 1000, 1000, 1000, 1000, 0, 0 vehiclespeed3 = vss3, "Vehicle Speed 3", { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, 0, { prefSpeedUnits == 0 ? 200 : 300 }, 1000, 1000, 1000, 1000, 0, 0 vehiclespeed4 = vss4, "Vehicle Speed 4", { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, 0, { prefSpeedUnits == 0 ? 200 : 300 }, 1000, 1000, 1000, 1000, 0, 0 shaftspeed1 = ss1, "Shaft Speed 1", "RPM", 0, 10000, 10000, 10000, 10000, 10000, 0, 0 shaftspeed2 = ss2, "Shaft Speed 2", "RPM", 0, 10000, 10000, 10000, 10000, 10000, 0, 0 gear = gear, "Gear", "", -1, 6, 6, 6, 6, 6, 0 ,0 accelx = accelx, "Accel X", "ms-2", -59, 59, 59, 59, 59, 59, 2, 2 accely = accely, "Accel Y", "ms-2", -59, 59, 59, 59, 59, 59, 2, 2 accelz = accelz, "Accel Z", "ms-2", -59, 59, 59, 59, 59, 59, 2, 2 fuelcompsn= fuel_pct, "Ethanol Percentage","%", 0, 100, -1, -1, 85, 101, 1, 1 #if CELSIUS fueltempGauge1 = fuel_temp1, "Fuel Temp1", "°C", -40, 110, -100, -100, 95, 105, 0, 0 fueltempGauge2 = fuel_temp2, "Fuel Temp2", "°C", -40, 110, -100, -100, 95, 105, 0, 0 #else fueltempGauge1 = fuel_temp1, "Fuel Temp1", "°F", -40, 240, -100, -100, 200, 220, 0, 0 fueltempGauge2 = fuel_temp2, "Fuel Temp2", "°F", -40, 240, -100, -100, 200, 220, 0, 0 #endif fuelpressGauge1kpa = fuel_press1, "Fuel Pressure1", "kPa.d", -40, 240, -100, -100, 200, 220, 0, 0 fuelpressGauge1psi = fuel_press1_psi, "Fuel Pressure1", "psi.d", -40, 240, -100, -100, 200, 220, 0, 0 fuelpressGauge1bar = fuel_press1_bar, "Fuel Pressure1", "bar.d", -40, 240, -100, -100, 200, 220, 0, 0 fuelpressGauge2kpa = fuel_press2, "Fuel Pressure2", "kPa.d", -40, 240, -100, -100, 200, 220, 0, 0 fuelpressGauge2psi = fuel_press2_psi, "Fuel Pressure2", "psi.d", -40, 240, -100, -100, 200, 220, 0, 0 fuelpressGauge2bar = fuel_press2_bar, "Fuel Pressure1", "bar.d", -40, 240, -100, -100, 200, 220, 0, 0 TPSADCGauge = tpsADC, "TPS ADC", "ADC", 0, 1023, -1, 1, 1024, 1024, 0, 0 load_duty = load_duty, "Alternator Load Duty", "%", 0, 100, 100, 100, 100, 100, 0, 0 batt_curr = batt_curr, "Battery Current", "A", -100, 100, 200, 200, 200, 200, 1, 1 gaugeCategory = "Sensor inputs3" vvtGauge1 = vvt_ang1, "VVT 1 angle", "degrees", 0, 50, -1, -1, 999, 999, 1, 1 vvtGauge2 = vvt_ang2, "VVT 2 angle", "degrees", 0, 50, -1, -1, 999, 999, 1, 1 vvtGauge3 = vvt_ang3, "VVT 3 angle", "degrees", 0, 50, -1, -1, 999, 999, 1, 1 vvtGauge4 = vvt_ang4, "VVT 4 angle", "degrees", 0, 50, -1, -1, 999, 999, 1, 1 knock01Gauge = knock_cyl01, "Knock cyl# 1", "", 0, 100, 0, 0, 100, 100, 1, 0 knock02Gauge = knock_cyl02, "Knock cyl# 2", "", 0, 100, 0, 0, 100, 100, 1, 0 knock03Gauge = knock_cyl03, "Knock cyl# 3", "", 0, 100, 0, 0, 100, 100, 1, 0 knock04Gauge = knock_cyl04, "Knock cyl# 4", "", 0, 100, 0, 0, 100, 100, 1, 0 knock05Gauge = knock_cyl05, "Knock cyl# 5", "", 0, 100, 0, 0, 100, 100, 1, 0 knock06Gauge = knock_cyl06, "Knock cyl# 6", "", 0, 100, 0, 0, 100, 100, 1, 0 knock07Gauge = knock_cyl07, "Knock cyl# 7", "", 0, 100, 0, 0, 100, 100, 1, 0 knock08Gauge = knock_cyl08, "Knock cyl# 8", "", 0, 100, 0, 0, 100, 100, 1, 0 #if CYL_12_16_SUPPORT knock09Gauge = knock_cyl09, "Knock cyl# 9", "", 0, 100, 0, 0, 100, 100, 1, 0 knock10Gauge = knock_cyl10, "Knock cyl#10", "", 0, 100, 0, 0, 100, 100, 1, 0 knock11Gauge = knock_cyl11, "Knock cyl#11", "", 0, 100, 0, 0, 100, 100, 1, 0 knock12Gauge = knock_cyl12, "Knock cyl#12", "", 0, 100, 0, 0, 100, 100, 1, 0 knock13Gauge = knock_cyl13, "Knock cyl#13", "", 0, 100, 0, 0, 100, 100, 1, 0 knock14Gauge = knock_cyl14, "Knock cyl#14", "", 0, 100, 0, 0, 100, 100, 1, 0 knock15Gauge = knock_cyl15, "Knock cyl#15", "", 0, 100, 0, 0, 100, 100, 1, 0 knock16Gauge = knock_cyl16, "Knock cyl#16", "", 0, 100, 0, 0, 100, 100, 1, 0 #endif gaugeCategory = "Sensor inputs4" gps_latdeggauge = gps_latdeg, "GPS Latitude deg", "deg", -90, +90, -90, -90, 90, 90, 0, 0 gps_latmingauge = gps_latmin, "GPS Latitude min", "min", 0, +60, 0, 0, 60, 60, 0, 0 gps_latsecgauge = gps_latsec, "GPS Latitude sec", "sec", 0, +60, 0, 0, 60, 60, 3, 3 gps_londeggauge = gps_londeg, "GPS Longitude deg", "deg", 0, +180, 0, 0, 180, 180, 0, 0 gps_lonmingauge = gps_lonmin, "GPS Longitude min", "min", 0, +60, 0, 0, 60, 60, 0, 0 gps_lonsecgauge = gps_lonsec, "GPS Longitude sec", "sec", 0, +60, 0, 0, 60, 60, 3, 3 gps_lonEWgauge = gps_lonEW, "GPS Longitude E/W", "E/W", 0, 255, 0, 0, 255, 255, 0, 0 gps_altgauge = gps_alt, "GPS Altitude", "m", -100, +13000, -100, -100, 13000, 13000, 1, 1 gps_speedgauge = gps_speed, "GPS Speed", { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, 0, { prefSpeedUnits == 0 ? 200 : 300 }, 1000, 1000, 1000, 1000, 0, 0 gps_coursegauge = gps_course, "GPS Course", "deg", 0, 360, 0, 0, 360, 360, 1, 1 gps_latitudegauge = gps_latitude, "GPS Latitude", "deg", -90, +90, -90, -90, 90, 90, 5, 5 gps_longitudegauge = gps_longitude, "GPS Longitude", "deg", -180, +180, -180, -180, 180, 180, 5, 5 gaugeCategory = "AFR/EGO inputs" #if NARROW_BAND_EGO egoV1Gauge = egov1, "Exhaust Gas Oxygen 1", "volts", 0, 1, 1, 1, 1, 1, 2, 2 egoV2Gauge = egov2, "Exhaust Gas Oxygen 2", "volts", 0, 1, 1, 1, 1, 1, 2, 2 egoV3Gauge = egov3, "Exhaust Gas Oxygen 3", "volts", 0, 1, 1, 1, 1, 1, 2, 2 egoV4Gauge = egov4, "Exhaust Gas Oxygen 4", "volts", 0, 1, 1, 1, 1, 1, 2, 2 egoV5Gauge = egov5, "Exhaust Gas Oxygen 5", "volts", 0, 1, 1, 1, 1, 1, 2, 2 egoV6Gauge = egov6, "Exhaust Gas Oxygen 6", "volts", 0, 1, 1, 1, 1, 1, 2, 2 egoV7Gauge = egov7, "Exhaust Gas Oxygen 7", "volts", 0, 1, 1, 1, 1, 1, 2, 2 egoV8Gauge = egov8, "Exhaust Gas Oxygen 8", "volts", 0, 1, 1, 1, 1, 1, 2, 2 #elif LAMBDA lambda1Gauge = lambda1, "Lambda 1", "", 0.5, 1.5, 0.5, 0.7, 2, 1.1, 2, 2 lambda2Gauge = lambda2, "Lambda 2", "", 0.5, 1.5, 0.5, 0.7, 2, 1.1, 2, 2 lambda3Gauge = lambda3, "Lambda 3", "", 0.5, 1.5, 0.5, 0.7, 2, 1.1, 2, 2 lambda4Gauge = lambda4, "Lambda 4", "", 0.5, 1.5, 0.5, 0.7, 2, 1.1, 2, 2 lambda5Gauge = lambda5, "Lambda 5", "", 0.5, 1.5, 0.5, 0.7, 2, 1.1, 2, 2 lambda6Gauge = lambda6, "Lambda 6", "", 0.5, 1.5, 0.5, 0.7, 2, 1.1, 2, 2 lambda7Gauge = lambda7, "Lambda 7", "", 0.5, 1.5, 0.5, 0.7, 2, 1.1, 2, 2 lambda8Gauge = lambda8, "Lambda 8", "", 0.5, 1.5, 0.5, 0.7, 2, 1.1, 2, 2 egoV1Gauge = egov1, "Exhaust Gas Oxygen 1", "volts", 0, 5, 5, 5, 5, 5, 2, 2 egoV2Gauge = egov2, "Exhaust Gas Oxygen 2", "volts", 0, 5, 5, 5, 5, 5, 2, 2 egoV3Gauge = egov3, "Exhaust Gas Oxygen 3", "volts", 0, 5, 5, 5, 5, 5, 2, 2 egoV4Gauge = egov4, "Exhaust Gas Oxygen 4", "volts", 0, 5, 5, 5, 5, 5, 2, 2 egoV5Gauge = egov5, "Exhaust Gas Oxygen 5", "volts", 0, 5, 5, 5, 5, 5, 2, 2 egoV6Gauge = egov6, "Exhaust Gas Oxygen 6", "volts", 0, 5, 5, 5, 5, 5, 2, 2 egoV7Gauge = egov7, "Exhaust Gas Oxygen 7", "volts", 0, 5, 5, 5, 5, 5, 2, 2 egoV8Gauge = egov8, "Exhaust Gas Oxygen 8", "volts", 0, 5, 5, 5, 5, 5, 2, 2 #else afr1Gauge = afr1, "Air:Fuel Ratio 1", "", 10, 19.4, 12, 13, 15, 16, 2, 2 afr2Gauge = afr2, "Air:Fuel Ratio 2", "", 10, 19.4, 12, 13, 15, 16, 2, 2 afr3Gauge = afr3, "Air:Fuel Ratio 3", "", 10, 19.4, 12, 13, 15, 16, 2, 2 afr4Gauge = afr4, "Air:Fuel Ratio 4", "", 10, 19.4, 12, 13, 15, 16, 2, 2 afr5Gauge = afr5, "Air:Fuel Ratio 5", "", 10, 19.4, 12, 13, 15, 16, 2, 2 afr6Gauge = afr6, "Air:Fuel Ratio 6", "", 10, 19.4, 12, 13, 15, 16, 2, 2 afr7Gauge = afr7, "Air:Fuel Ratio 7", "", 10, 19.4, 12, 13, 15, 16, 2, 2 afr8Gauge = afr8, "Air:Fuel Ratio 8", "", 10, 19.4, 12, 13, 15, 16, 2, 2 egoV1Gauge = egov1, "Exhaust Gas Oxygen 1", "volts", 0, 5, 5, 5, 5, 5, 2, 2 egoV2Gauge = egov2, "Exhaust Gas Oxygen 2", "volts", 0, 5, 5, 5, 5, 5, 2, 2 egoV3Gauge = egov3, "Exhaust Gas Oxygen 3", "volts", 0, 5, 5, 5, 5, 5, 2, 2 egoV4Gauge = egov4, "Exhaust Gas Oxygen 4", "volts", 0, 5, 5, 5, 5, 5, 2, 2 egoV5Gauge = egov5, "Exhaust Gas Oxygen 5", "volts", 0, 5, 5, 5, 5, 5, 2, 2 egoV6Gauge = egov6, "Exhaust Gas Oxygen 6", "volts", 0, 5, 5, 5, 5, 5, 2, 2 egoV7Gauge = egov7, "Exhaust Gas Oxygen 7", "volts", 0, 5, 5, 5, 5, 5, 2, 2 egoV8Gauge = egov8, "Exhaust Gas Oxygen 8", "volts", 0, 5, 5, 5, 5, 5, 2, 2 #endif gaugeCategory = "AFR/EGO calculations" #if NARROW_BAND_EGO afr1targetGauge = afrtgt1, "EgoV 1 Target", "", 0, 1, 20, 20, 20, 20, 3, 3 afr2targetGauge = afrtgt2, "EgoV 2 Target", "", 0, 1, 20, 20, 20, 20, 3, 3 afr1errGauge = afr1err, "EgoV 1 Error", "", -1, +1, 12, 13, 15, 16, 3, 3 afr2errGauge = afr2err, "EgoV 2 Error", "", -1, +1, 12, 13, 15, 16, 3, 3 #elif LAMBDA afr1targetGauge = afrtgt1, "Lambda 1 Target", "", 0.5, 1.5, 20, 20, 20, 20, 2, 2 afr2targetGauge = afrtgt2, "Lambda 2 Target", "", 0.5, 1.5, 20, 20, 20, 20, 2, 2 afr1errGauge = afr1err, "Lambda 1 Error", "", -2, +2, 12, 13, 15, 16, 2, 2 afr2errGauge = afr2err, "Lambda 2 Error", "", -2, +2, 12, 13, 15, 16, 2, 2 #else afr1targetGauge = afrtgt1, "AFR 1 Target", "", 10, 19.4, 20, 20, 20, 20, 2, 2 afr2targetGauge = afrtgt2, "AFR 2 Target", "", 10, 19.4, 20, 20, 20, 20, 2, 2 afr1errGauge = afr1err, "AFR 1 Error", "", -5, +5, 12, 13, 15, 16, 2, 2 afr2errGauge = afr2err, "AFR 2 Error", "", -5, +5, 12, 13, 15, 16, 2, 2 #endif egoCorrGauge1 = egocor1, "EGO Correction 1", "%", 50, 150, 90, 99, 101, 110, 1, 1 egoCorrGauge2 = egocor2, "EGO Correction 2", "%", 50, 150, 90, 99, 101, 110, 1, 1 egoCorrGauge3 = egocor3, "EGO Correction 3", "%", 50, 150, 90, 99, 101, 110, 1, 1 egoCorrGauge4 = egocor4, "EGO Correction 4", "%", 50, 150, 90, 99, 101, 110, 1, 1 egoCorrGauge5 = egocor5, "EGO Correction 5", "%", 50, 150, 90, 99, 101, 110, 1, 1 egoCorrGauge6 = egocor6, "EGO Correction 6", "%", 50, 150, 90, 99, 101, 110, 1, 1 egoCorrGauge7 = egocor7, "EGO Correction 7", "%", 50, 150, 90, 99, 101, 110, 1, 1 egoCorrGauge8 = egocor8, "EGO Correction 8", "%", 50, 150, 90, 99, 101, 110, 1, 1 stoichGauge = Stoich, "Stoich", "", 10, 19.4, 12, 13, 15, 16, 2, 2 #if CYL_12_16_SUPPORT gaugeCategory = "AFR/EGO inputs 9-16" #if NARROW_BAND_EGO ; #elif LAMBDA lambda9Gauge = lambda9, "Lambda 9", "", 0.5, 1.5, 0.5, 0.7, 2, 1.1, 2, 2 lambda10Gauge = lambda10, "Lambda 10", "", 0.5, 1.5, 0.5, 0.7, 2, 1.1, 2, 2 lambda11Gauge = lambda11, "Lambda 11", "", 0.5, 1.5, 0.5, 0.7, 2, 1.1, 2, 2 lambda12Gauge = lambda12, "Lambda 12", "", 0.5, 1.5, 0.5, 0.7, 2, 1.1, 2, 2 lambda13Gauge = lambda13, "Lambda 13", "", 0.5, 1.5, 0.5, 0.7, 2, 1.1, 2, 2 lambda14Gauge = lambda14, "Lambda 14", "", 0.5, 1.5, 0.5, 0.7, 2, 1.1, 2, 2 lambda15Gauge = lambda15, "Lambda 15", "", 0.5, 1.5, 0.5, 0.7, 2, 1.1, 2, 2 lambda16Gauge = lambda16, "Lambda 16", "", 0.5, 1.5, 0.5, 0.7, 2, 1.1, 2, 2 #else afr9Gauge = afr9, "Air:Fuel Ratio 9", "", 10, 19.4, 12, 13, 15, 16, 2, 2 afr10Gauge = afr10, "Air:Fuel Ratio 10", "", 10, 19.4, 12, 13, 15, 16, 2, 2 afr11Gauge = afr11, "Air:Fuel Ratio 11", "", 10, 19.4, 12, 13, 15, 16, 2, 2 afr12Gauge = afr12, "Air:Fuel Ratio 12", "", 10, 19.4, 12, 13, 15, 16, 2, 2 afr13Gauge = afr13, "Air:Fuel Ratio 13", "", 10, 19.4, 12, 13, 15, 16, 2, 2 afr14Gauge = afr14, "Air:Fuel Ratio 14", "", 10, 19.4, 12, 13, 15, 16, 2, 2 afr15Gauge = afr15, "Air:Fuel Ratio 15", "", 10, 19.4, 12, 13, 15, 16, 2, 2 afr16Gauge = afr16, "Air:Fuel Ratio 16", "", 10, 19.4, 12, 13, 15, 16, 2, 2 #endif egoV9Gauge = egov9, "Exhaust Gas Oxygen 9", "volts", 0, 5, 5, 5, 5, 5, 2, 2 egoV10Gauge = egov10, "Exhaust Gas Oxygen 10", "volts", 0, 5, 5, 5, 5, 5, 2, 2 egoV11Gauge = egov11, "Exhaust Gas Oxygen 11", "volts", 0, 5, 5, 5, 5, 5, 2, 2 egoV12Gauge = egov12, "Exhaust Gas Oxygen 12", "volts", 0, 5, 5, 5, 5, 5, 2, 2 egoV13Gauge = egov13, "Exhaust Gas Oxygen 13", "volts", 0, 5, 5, 5, 5, 5, 2, 2 egoV14Gauge = egov14, "Exhaust Gas Oxygen 14", "volts", 0, 5, 5, 5, 5, 5, 2, 2 egoV15Gauge = egov15, "Exhaust Gas Oxygen 15", "volts", 0, 5, 5, 5, 5, 5, 2, 2 egoV16Gauge = egov16, "Exhaust Gas Oxygen 16", "volts", 0, 5, 5, 5, 5, 5, 2, 2 gaugeCategory = "AFR/EGO calculations 9-16" egoCorrGauge9 = egocor9, "EGO Correction 9", "%", 50, 150, 90, 99, 101, 110, 1, 1 egoCorrGauge10 = egocor10, "EGO Correction 10", "%", 50, 150, 90, 99, 101, 110, 1, 1 egoCorrGauge11 = egocor11, "EGO Correction 11", "%", 50, 150, 90, 99, 101, 110, 1, 1 egoCorrGauge12 = egocor12, "EGO Correction 12", "%", 50, 150, 90, 99, 101, 110, 1, 1 egoCorrGauge13 = egocor13, "EGO Correction 13", "%", 50, 150, 90, 99, 101, 110, 1, 1 egoCorrGauge14 = egocor14, "EGO Correction 14", "%", 50, 150, 90, 99, 101, 110, 1, 1 egoCorrGauge15 = egocor15, "EGO Correction 15", "%", 50, 150, 90, 99, 101, 110, 1, 1 egoCorrGauge16 = egocor16, "EGO Correction 16", "%", 50, 150, 90, 99, 101, 110, 1, 1 #endif gaugeCategory = "Generic sensor inputs" sensor01Gauge = sensor01, { stringValue(sensor01Alias) }, "", -3000, 3000, -3277, -3277, 3277, 3277, 1, 1 sensor02Gauge = sensor02, { stringValue(sensor02Alias) }, "", -3000, 3000, -3277, -3277, 3277, 3277, 1, 1 sensor03Gauge = sensor03, { stringValue(sensor03Alias) }, "", -3000, 3000, -3277, -3277, 3277, 3277, 1, 1 sensor04Gauge = sensor04, { stringValue(sensor04Alias) }, "", -3000, 3000, -3277, -3277, 3277, 3277, 1, 1 sensor05Gauge = sensor05, { stringValue(sensor05Alias) }, "", -3000, 3000, -3277, -3277, 3277, 3277, 1, 1 sensor06Gauge = sensor06, { stringValue(sensor06Alias) }, "", -3000, 3000, -3277, -3277, 3277, 3277, 1, 1 sensor07Gauge = sensor07, { stringValue(sensor07Alias) }, "", -3000, 3000, -3277, -3277, 3277, 3277, 1, 1 sensor08Gauge = sensor08, { stringValue(sensor08Alias) }, "", -3000, 3000, -3277, -3277, 3277, 3277, 1, 1 sensor09Gauge = sensor09, { stringValue(sensor09Alias) }, "", -3000, 3000, -3277, -3277, 3277, 3277, 1, 1 sensor10Gauge = sensor10, { stringValue(sensor10Alias) }, "", -3000, 3000, -3277, -3277, 3277, 3277, 1, 1 sensor11Gauge = sensor11, { stringValue(sensor11Alias) }, "", -3000, 3000, -3277, -3277, 3277, 3277, 1, 1 sensor12Gauge = sensor12, { stringValue(sensor12Alias) }, "", -3000, 3000, -3277, -3277, 3277, 3277, 1, 1 sensor13Gauge = sensor13, { stringValue(sensor13Alias) }, "", -3000, 3000, -3277, -3277, 3277, 3277, 1, 1 sensor14Gauge = sensor14, { stringValue(sensor14Alias) }, "", -3000, 3000, -3277, -3277, 3277, 3277, 1, 1 sensor15Gauge = sensor15, { stringValue(sensor15Alias) }, "", -3000, 3000, -3277, -3277, 3277, 3277, 1, 1 sensor16Gauge = sensor16, { stringValue(sensor16Alias) }, "", -3000, 3000, -3277, -3277, 3277, 3277, 1, 1 gaugeCategory = "CAN board inputs/outputs" canin1_8Gauge = canin1_8, "CAN inputs 1-8", "", 0, 255, 255, 255, 255, 255,0, 0 canout1_8Gauge = canout1_8, "CAN outputs 1-8", "", 0, 255, 255, 255, 255, 255,0, 0 canout9_16Gauge = canout9_16, "CAN outputs 9-16", "", 0, 255, 255, 255, 255, 255,0, 0 canpwmin0Gauge = canpwmin0, "CAN PWMin 0", "", 0, 65535, 65535, 65535, 65535, 65535,0, 0 canpwmin1Gauge = canpwmin1, "CAN PWMin 1", "", 0, 65535, 65535, 65535, 65535, 65535,0, 0 canpwmin2Gauge = canpwmin2, "CAN PWMin 2", "", 0, 65535, 65535, 65535, 65535, 65535,0, 0 canpwmin3Gauge = canpwmin3, "CAN PWMin 3", "", 0, 65535, 65535, 65535, 65535, 65535,0, 0 gaugeCategory = "X-Code dev" status1Gauge = status1, "Status 1", "", 0, 255, 255, 255, 255, 255, 0, 0 status2Gauge = status2, "Status 2", "", 0, 255, 255, 255, 255, 255, 0, 0 status3Gauge = status3, "Status 3", "", 0, 255, 255, 255, 255, 255, 0, 0 status4Gauge = status4, "Status 4", "", 0, 255, 255, 255, 255, 255, 0, 0 status5Gauge = status5, "Status 5", "", 0, 65535, 65535, 65535, 65535, 65535,0, 0 status6Gauge = status6, "Status 6", "", 0, 255, 255, 255, 255, 255, 0, 0 status7Gauge = status7, "Status 7", "", 0, 255, 255, 255, 255, 255, 0, 0 status8Gauge = status8, "Status 8", "", 0, 255, 255, 255, 255, 255, 0, 0 injcountGauge = status5, "Injection Count", "pulses", 0, 1000, 65535, 65535, 65535, 65535,0, 0 looptimeGauge = looptime, "Mainloop time", "us", 0, 10000, -1, -1, 1000, 6000, 0, 0 sd_filenum = sd_filenum, "SDcard file number", "", 0, 9999, 9999, 9999, 9999, 9999, 0 ,0 sd_error = sd_error, "SDcard error", "", 0, 255, 255, 255, 255, 255, 0 ,0 sd_status = sd_status, "SDcard status", "", 0, 255, 255, 255, 255, 255, 0 ,0 sd_phase = sd_phase, "SDcard phase", "", 0, 255, 255, 255, 255, 255, 0 ,0 deadGauge = deadValue, "---", "", 0, 1, -1, -1, 2, 2, 0, 0 advBucketGauge = veTuneValue, "Advance Bucket", "degrees", 0, 55, -1, -1, 999, 999, 1, 1 veBucketGauge = veTuneValue, "VE Value", "%", 0, 120, -1, -1, 999, 999, 0, 0 cel_statusGauge = cel_status, "CEL Status", "", 0, 65535, 65535, 65535, 65535, 65535, 0, 0 cel_status2Gauge = cel_status2, "CEL Status2", "", 0, 65535, 65535, 65535, 65535, 65535, 0, 0 cel_errorcodeGauge = cel_errorcode, "CEL Error code", "", 0, 32, 32, 32, 32, 32, 0, 0 ;------------------------------------------------------------------------------ [FrontPage] #if NARROW_BAND_EGO egoLEDs = 0.0, 1.0, 0.5 ; Voltage settings. #elif LAMBDA egoLEDs = 1.5, 0.5, 1.0 ; Lambda settings. #else egoLEDs = 19.7, 9.7, 14.7 ; Afr settings. #endif ; Gauges are numbered left to right, top to bottom. ; ; 1 2 3 4 ; 5 6 7 8 gauge1 = tachometer ; gauge2 = EAEGauge1 gauge2 = throttleGauge gauge3 = pulseWidth1Gauge gauge4 = cltGauge gauge5 = advdegGauge gauge6 = fuelloadGauge #if NARROW_BAND_EGO gauge7 = egoV1Gauge #elif LAMBDA gauge7 = lambda1Gauge #else gauge7 = afr1Gauge #endif ; gauge7 = dwellGauge ; gauge8 = matGauge gauge8 = lostsyncGauge ;---------------------------------------------------------------------------- ; Indicators ; expr off-label on-label, off-bg, off-fg, on-bg, on-fg indicator = { ready }, "Not Ready", "Ready", white, black, green, black indicator = { crank }, "Not Cranking", "Cranking", white, black, green, black indicator = { startw }, "ASE OFF", "ASE", white, black, green, black indicator = { warmup }, "WUE OFF", "WUE", white, black, green, black indicator = { tpsaccaen }, "TPS Accel", "TPS Accel", white, black, green, black indicator = { mapaccaen }, "MAP Accel", "MAP Accel", white, black, green, black indicator = { tpsaccden }, "TPS Decel", "TPS Decel", white, black, green, black indicator = { mapaccden }, "MAP Decel", "MAP Decel", white, black, green, black ; indicator = { tps > floodClear && crank }, "", "FLOOD CLEAR", white, black, red, black indicator = { status1 & 1}, "Need Burn", "Need Burn", white, black, red, black indicator = { status1 & 2}, "Data Lost", "Lost Data", white, black, red, black indicator = { status1 & 4}, "Config Error", "Config Error", white, black, red, black indicator = { status1 & 8}, "Not RPM synced", "RPM Synced", red, black, green, black indicator = { status1 & 32}, "VE1/2", "VE3/4", white, black, green, black indicator = { status1 & 64}, "SPK1/2", "SPK3/4", white, black, green, black indicator = { status1 & 128}, "Half-RPM sync", "Full-RPM sync", white, black, green, black indicator = { status2 & 1}, "N2O 1 off", "N2O 1 on", white, black, green, black indicator = { status2 & 2}, "N2O 2 off", "N2O 2 on", white, black, green, black indicator = { status2 & 4}, "No Launch", "Launch in", white, black, green, black indicator = { status2 & 16}, "No Flat shift", "Flat shift", white, black, green, black indicator = { status2 & 32}, "Spark cut", "Spark cut", white, black, red, black indicator = { status2 & 64}, "Over boost", "Over boost", white, black, red, black indicator = { status2 & 128}, "CL Idle off", "CL idle on", white, black, green, black indicator = { status3 & 1}, "No Fuel cut", "Fuel cut", white, black, red, black indicator = { status3 & 2}, "T-log", "T-log", white, black, green, black indicator = { status3 & 4}, "3 step off", "3 step on", white, black, green, black indicator = { status3 & 8}, "Test mode", "Test mode", white, black, yellow, black indicator = { status3 & 16}, "No 3 step", "3 step in", white, black, green, black indicator = { status3 & 32}, "No soft limit", "Soft limiter",white, black, red, black indicator = { status3 & 64}, "No seq. shift", "Seq. Shift", white, black, red, black indicator = { status3 & 128}, "Launch Off", "Launch on", white, black, red, black indicator = { status6 & 1}, "EGT warn", "EGT warn", white, black, red, black indicator = { status6 & 2}, "EGT shutdown", "EGT shutdown", white, black, red, black indicator = { status6 & 4}, "AFR warn", "AFR warn", white, black, red, black indicator = { status6 & 8}, "AFR shutdown", "AFR shutdown", white, black, red, black indicator = { status6 & 16}, "Idle VE", "Idle VE", white, black, green, black indicator = { status6 & 32}, "Idle Adv", "Idle Adv", white, black, green, black indicator = { status6 & 64}, "Fan", "Fan", white, black, green, black indicator = { status6 & 128}, "MAPsample error!", "MAPsample error!", white, black, red, black indicator = { status7 & 1}, "VVT1 err", "VVT1 err", white, black, red, black indicator = { status7 & 2}, "VVT2 err", "VVT2 err", white, black, red, black indicator = { status7 & 4}, "VVT3 err", "VVT3 err", white, black, red, black indicator = { status7 & 8}, "VVT4 err", "VVT4 err", white, black, red, black indicator = { status7 & 16}, "No Knock", "Knock", white, black, red, black indicator = { status7 & 32}, "AC", "AC", white, black, green, black indicator = { status7 & 64}, "Check Engine", "Check Engine", white, black, red, black indicator = { status7 & 128}, "Limp mode", "Limp mode", white, black, red, black indicator = { status8 & 4}, "W.I. low", "W.I. low!", white, black, red, black indicator = { status8 & 8}, "PW4X", "PW4X", white, black, red, black indicator = { status8 & 16}, "VSS launch L/O", "VSS launch L/O", white, black, red, black indicator = { status8 & 32}, "VSS launch on", "VSS launch on", white, black, red, black indicator = { sd_status & 1}, "No SD", "SD in", white, black, green, black indicator = { sd_status & 4}, "SD ready", "SD ready", white, black, green, black indicator = { sd_status & 8}, "SD Log", "SD Log", white, black, green, black indicator = { sd_status & 16}, "SD Err", "SD Err", white, black, red, black indicator = { (gammaEnrich < 70) }, "-", "Tune error", white, black, red, black #if PORT_STATUS indicator = { porta0 }, "PORTA0", "PORTA0", white, black, green, black indicator = { porta1 }, "PORTA1", "PORTA1", white, black, green, black indicator = { porta2 }, "PORTA2", "PORTA2", white, black, green, black indicator = { porta3 }, "PORTA3", "PORTA3", white, black, green, black indicator = { porta4 }, "PORTA4", "PORTA4", white, black, green, black indicator = { porta5 }, "PORTA5", "PORTA5", white, black, green, black indicator = { porta6 }, "PORTA6", "PORTA6", white, black, green, black indicator = { porta7 }, "PORTA7", "PORTA7", white, black, green, black indicator = { portb0 }, "PORTB0", "PORTB0", white, black, green, black indicator = { portb1 }, "PORTB1", "PORTB1", white, black, green, black indicator = { portb2 }, "PORTB2", "PORTB2", white, black, green, black indicator = { portb3 }, "PORTB3", "PORTB3", white, black, green, black indicator = { portb4 }, "PORTB4", "PORTB4", white, black, green, black indicator = { portb5 }, "PORTB5", "PORTB5", white, black, green, black indicator = { portb6 }, "PORTB6", "PORTB6", white, black, green, black indicator = { portb7 }, "PORTB7", "PORTB7", white, black, green, black indicator = { porte0 }, "PORTE0", "PORTE0", white, black, green, black indicator = { porte1 }, "PORTE1", "PORTE1", white, black, green, black indicator = { porte2 }, "PORTE2", "PORTE2", white, black, green, black indicator = { porte4 }, "PORTE4", "PORTE4", white, black, green, black indicator = { porth6 }, "PORTH6", "PORTH6", white, black, green, black indicator = { porth7 }, "PORTH7", "PORTH7", white, black, green, black indicator = { portk0 }, "PORTK0", "PORTK0", white, black, green, black indicator = { portk1 }, "PORTK1", "PORTK1", white, black, green, black indicator = { portk2 }, "PORTK2", "PORTK2", white, black, green, black indicator = { portk3 }, "PORTK3", "PORTK3", white, black, green, black indicator = { portk7 }, "PORTK7", "PORTK7", white, black, green, black indicator = { portj0 }, "PORTJ0", "PORTJ0", white, black, green, black indicator = { portj1 }, "PORTJ1", "PORTJ1", white, black, green, black indicator = { portm2 }, "PORTM2", "PORTM2", white, black, green, black indicator = { portm3 }, "PORTM3", "PORTM3", white, black, green, black indicator = { portm4 }, "PORTM4", "PORTM4", white, black, green, black indicator = { portm5 }, "PORTM5", "PORTM5", white, black, green, black indicator = { portj7 }, "PORTJ7", "PORTJ7", white, black, green, black indicator = { portp2 }, "PORTP2", "PORTP2", white, black, green, black indicator = { portp3 }, "PORTP3", "PORTP3", white, black, green, black indicator = { portp4 }, "PORTP4", "PORTP4", white, black, green, black indicator = { portp5 }, "PORTP5", "PORTP5", white, black, green, black indicator = { portp6 }, "PORTP6", "PORTP6", white, black, green, black indicator = { portp7 }, "PORTP7", "PORTP7", white, black, green, black indicator = { portt0 }, "PORTT0", "PORTT0", white, black, green, black indicator = { portt1 }, "PORTT1", "PORTT1", white, black, green, black indicator = { portt2 }, "PORTT2", "PORTT2", white, black, green, black indicator = { portt3 }, "PORTT3", "PORTT3", white, black, green, black indicator = { portt4 }, "PORTT4", "PORTT4", white, black, green, black indicator = { portt5 }, "PORTT5", "PORTT5", white, black, green, black indicator = { portt6 }, "PORTT6", "PORTT6", white, black, green, black #endif indicator = { cel_status_map }, "MAP fault", "MAP fault", white, black, red, black ; 1 indicator = { cel_status_mat }, "MAT fault", "MAT fault", white, black, red, black ; 2 indicator = { cel_status_clt }, "CLT fault", "CLT fault", white, black, red, black ; 4 indicator = { cel_status_tps }, "TPS fault", "TPS fault", white, black, red, black ; 8 indicator = { cel_status_batt }, "BATT fault", "BATT fault", white, black, red, black ; 16 indicator = { cel_status_afr0 }, "AFR0 fault", "AFR0 fault", white, black, red, black ; 32 indicator = { cel_status_sync }, "SYNC fault", "SYNC fault", white, black, red, black ; 64 indicator = { cel_status_egt }, "EGT fault", "EGT fault", white, black, red, black ; 128 indicator = { cel_status_flex }, "Flex fault", "Flex fault", white, black, red, black ;256 indicator = { cel_status_maf }, "MAF fault", "MAF fault", white, black, red, black ; 512 indicator = { cel_status_knock }, "Knock fault", "Knock fault", white, black, red, black ; 1024 indicator = { cel_status_cam }, "Cam fault", "Cam fault", white, black, red, black ; 2048 indicator = { cel_status_oil}, "Oil fault", "Oil fault", white, black, red, black ; 4096 indicator = { cel_status_fp}, "Fuel press.", "Fuel press.", white, black, red, black ; 4096 indicator = { cel_status_egtshut}, "CEL EGT shutdown", "CEL EGT shutdown", white, black, red, black ; 16384 indicator = { cel_status_afrshut}, "CEL AFR shutdown", "CEL AFR shutdown", white, black, red, black ; 32768 indicator = { cel_status2_winj}, "CEL W.Inj low", "CEL W.Inj low", white, black, red, black ; 1 indicator = { cel_status2_shutd}, "Safety shutdown", "Safety shutdown", white, black, red, black ; 2 ;------------------------------------------------------------------------------- [RunTime] barHysteresis = 2.5 ; Seconds coolantBar = {cltlowlim}, {clthighlim} matBar = -40, {mathigh} batteryBar = 6, 15 dutyCycleBar = 0, 100 #if NARROW_BAND_EGO egoBar = 0.0 , 1.0 #elif LAMBDA egoBar = 0.5, 1.5 #else egoBar = 9.7, 19.7 #endif gammaEBar = 0, 200 mapBar = 0, 255 pulseWidthBar = 0, 25.5 rpmBar = 0, {rpmhigh} throttleBar = 0, 100 egoCorrBar = 0, 200 baroCorrBar = 0, 200 warmupCorrBar = 0, 200 airdenCorrBar = 0, 200 veCorrBar = 0, 200 accCorrBar = 0, 100 ;------------------------------------------------------------------------------- [Tuning] #if NARROW_BAND_EGO egoLEDs = 0.0, 1.0, 0.5 ; Voltage settings. #elif LAMBDA egoLEDs = 1.5, 0.5, 1.0 ; Lambda settings. #else egoLEDs = 19.7, 9.7, 14.7 ; Afr settings. #endif ; font = "Lucida Console", 12 ; font = "Courier", 14 spotDepth = 2 ; 0 = no indicators, 1 = Z only, 2 = XYZ indicators. cursorDepth = 2 ; Same as spot depth. ; The four radio buttons on the tuning screen select a "page" of six ; gauges. The gauge numbering is the same as the front page, across ; then down. ; 1 2 ; 3 4 ; 5 6 ; ; gaugeColumns allows you to hide or show gauges in column 2 (i.e., ; gauges 2, 4 and 6). gaugeColumns = 2 ; Only 1 or 2 are valid. ; Page 1 Page 2 Page 3 Page 4 pageButtons = "&EGO", "&WUE", "PW&1", "PW&2" gauge1 = tachometer, tachometer, tachometer, tachometer gauge2 = mapGauge, mapGauge, mapGauge, mapGauge #if NARROW_BAND_EGO gauge3 = egoV1Gauge, egoV1Gauge, egoV1Gauge, egoV1Gauge #elif LAMBDA gauge3 = lambda1Gauge, lambda1Gauge, lambda1Gauge, lambda1Gauge #else gauge3 = afr1Gauge, afr1Gauge, afr1Gauge, afr1Gauge #endif gauge4 = egoCorrGauge1, warmupEnrichGauge, pulseWidth1Gauge, pulseWidth2Gauge gauge5 = veBucketGauge, veBucketGauge, veBucketGauge, veBucketGauge gauge6 = egoCorrGauge2, accelEnrichGauge, dutyCycle1Gauge, dutyCycle2Gauge ;------------------------------------------------------------------------------- [AccelerationWizard] tpsDotBar = 0, 800 mapDotBar = 0, 700 ;------------------------------------------------------------------------------- [BurstMode] ; getCommand = "a\x00\x06" getCommand = "A" [OutputChannels] deadValue = { 0 } ; Convenient unchanging value. ochBlockSize = 506 ; change this if adding extra data to outpc #if CAN_COMMANDS ochGetCommand = "r\$tsCanId\x07%2o%2c" ; leave this alone #else ; fast get via serial ochGetCommand = "A" #endif scatteredOffsetArray = qfrtfielddata scatteredOchGetCommand = "g" scatteredGetEnabled = { scatterRuntimeEnabled && (tsLocalCanId == tsCanId) } seconds = scalar, U16, 0, "s", 1.000, 0.0 secl = { seconds % 256 }, "s" ; For runtime screen. #if PW_4X pulseWidth1 = scalar, U16, 2, "ms", 0.004, 0.0 pulseWidth2 = scalar, U16, 4, "ms", 0.004, 0.0 #else pulseWidth1 = scalar, U16, 2, "ms", 0.001, 0.0 pulseWidth2 = scalar, U16, 4, "ms", 0.001, 0.0 #endif pulseWidth = { pulseWidth1 }, "ms" ; For runtime screen. rpm = scalar, U16, 6, "RPM", 1.000, 0.0 advance = scalar, S16, 8, "deg", 0.100, 0.0 ; unsigned char squirt,engine,afrtgt1,afrtgt2; // afrtgt in afr x 10 squirt = scalar, U08, 10, "bit", 1.000, 0.0 ; Squirt Event Scheduling Variables - bit fields for "squirt" variable above ; inj1: equ 3 ; 0 = no squirt 1 = squirt ; inj2: equ 5 ; 0 = no squirt 1 = squirt ; sched1: equ 2 ; 0 = nothing scheduled 1 = scheduled to squirt ; firing1: equ 0 ; 0 = not squirting 1 = squirting ; sched2: equ 4 ; firing2: equ 1 firing1 = bits, U08, 10, [0:0] firing2 = bits, U08, 10, [1:1] sched1 = bits, U08, 10, [2:2] inj1 = bits, U08, 10, [3:3] sched2 = bits, U08, 10, [4:4] inj2 = bits, U08, 10, [5:5] engine = scalar, U08, 11, "bit", 1.000, 0.0 ; Engine Operating/Status variables - bit fields for "engine" variable above ; ready: equ 0 ; 0 = engine not ready 1 = ready to run ; crank: equ 1 ; 0 = engine not cranking 1 = engine cranking ; startw: equ 2 ; 0 = not in startup warmup 1 = in warmup enrichment ; warmup: equ 3 ; 0 = not in warmup 1 = in warmup ; tpsaen: equ 4 ; 0 = not in TPS acceleration mode 1 = TPS acceleration mode ; tpsden: equ 5 ; 0 = not in deacceleration mode 1 = in deacceleration mode ready = bits, U08, 11, [0:0] crank = bits, U08, 11, [1:1] startw = bits, U08, 11, [2:2] warmup = bits, U08, 11, [3:3] tpsaccaen = bits, U08, 11, [4:4] tpsaccden = bits, U08, 11, [5:5] mapaccaen = bits, U08, 11, [6:6] mapaccden = bits, U08, 11, [7:7] #if NARROW_BAND_EGO afrtgt1 = scalar, U08, 12, "Volts", 0.00489, 0.0 afrtgt2 = scalar, U08, 13, "Volts", 0.00489, 0.0 #elif LAMBDA afrtgt1raw = scalar, U08, 12, "Lambda", 0.1, 0.0 afrtgt2raw = scalar, U08, 13, "Lambda", 0.1, 0.0 #else afrtgt1 = scalar, U08, 12, "AFR", 0.1, 0.0 afrtgt2 = scalar, U08, 13, "AFR", 0.1, 0.0 #endif ; unsigned char wbo2_en1,wbo2_en2; // from wbo2 - indicates whether wb afr valid wbo2_en1 = scalar, U08, 14, "", 1.000, 0.0 wbo2_en2 = scalar, U08, 15, "", 1.000, 0.0 ; int baro,map,mat,clt,tps,batt,ego1,ego2,knock, // baro - kpa x 10 ; // map - kpa x 10 ; // mat, clt deg(C/F)x 10 ; // tps - % x 10 ; // batt - vlts x 10 ; // ego1,2 - afr x 10 ; // knock - volts x 10 barometer = scalar, S16, 16, "kPa", 0.100, 0.0 map = scalar, S16, 18, "kPa", 0.100, 0.0 #if CELSIUS mat = scalar, S16, 20, "°C", 0.05555, -320.0 coolant = scalar, S16, 22, "°C", 0.05555, -320.0 #else mat = scalar, S16, 20, "°F", 0.100, 0.0 coolant = scalar, S16, 22, "°F", 0.100, 0.0 #endif tps = scalar, S16, 24, "%", 0.100, 0.0 throttle = { tps }, "%" batteryVoltage = scalar, S16, 26, "v", 0.100, 0.0 afr1_old = scalar, S16, 28, "AFR", 0.100, 0.0 afr2_old = scalar, S16, 30, "AFR", 0.100, 0.0 knock = scalar, S16, 32, "%", 0.100, 0.0 ; egocor1,egocor2,aircor,warmcor, // all in % egoCorrection1 = scalar, S16, 34, "%", 0.1000, 0.0 egoCorrection = { ( egoCorrection1 + egoCorrection2) / 2 }, "%" ; Alias for old gauges. egoCorrection2 = scalar, S16, 36, "%", 0.1000, 0.0 airCorrection = scalar, S16, 38, "%", 0.1000, 0.0 warmupEnrich = scalar, S16, 40, "%", 1.000, 0.0 ; tpsaccel,tpsfuelcut,barocor,gammae, // tpsaccel - acc enrich(.1 ms units) ; // tpsfuelcut - % ; // barcor,gammae - % accelEnrich = scalar, S16, 42, "ms", 0.100, 0.0 tpsfuelcut = scalar, S16, 44, "%", 1.000, 0.0 baroCorrection = scalar, S16, 46, "%", 0.1000, 0.0 gammaEnrich = scalar, S16, 48, "%", 1.000, 0.0 ; vecurr1,vecurr2,iacstep,cold_adv_deg; // vecurr - % ; // iacstep - steps ; // cold_adv_deg - deg x 10 veCurr1 = scalar, S16, 50, "%", 0.1000, 0.0 veCurr2 = scalar, S16, 52, "%", 0.1000, 0.0 veCurr = { veCurr1 }, "%" ; For runtime display. iacstep = scalar, S16, 54, "", 1.000, 0.0 idleDC = scalar, S16, 54, "%", 0.392, 0.0 coldAdvDeg = scalar, S16, 56, "deg", 0.100, 0.0 TPSdot = scalar, S16, 58, "%/s", 0.100, 0.0 MAPdot = scalar, S16, 60, "kPa/s", 1.000, 0.0 dwell = scalar, U16, 62, "ms", 0.1000, 0.0 mafload = scalar, S16, 64, "kPa", 0.1000, 0.0 fuelload = scalar, S16, 66, { bitStringValue( algorithmUnits , algorithm ) }, 0.100, 0.0 ; Blend of MAP and TPS, depends on algorithm fuelCorrection = scalar, S16, 68, "%", 1.000, 0.0 ; Correcton based on percent alcohol in fuel. sd_status = scalar, U08, 70, "", 1.0, 0.0 knockRetard = scalar, U08, 71, "deg", 0.1, 0.0 EAEFuelCorr1 = scalar, U16, 72, "%", 1.0, 0.0 egoV = scalar, S16, 74, "V", 0.01, 0.0 ; was omitted egoV2 = scalar, S16, 76, "V", 0.01, 0.0 ; was omitted status1 = scalar, U08, 78, "", 1.0, 0.0 ; status1 status2 = scalar, U08, 79, "", 1.0, 0.0 ; status2 status3 = scalar, U08, 80, "", 1.0, 0.0 ; status3 status4 = scalar, U08, 81, "", 1.0, 0.0 ; status4 status6 = scalar, U08, 82, "", 1.0, 0.0 status7 = scalar, U08, 83, "", 1.0, 0.0 status5 = scalar, U16, 84, "", 1, 0 ; istatus5 cel_status = scalar, U16, 86, "bit", 1.000, 0.0 ; engine fault bits cel_status_map = bits, U08, 87, [0:0] ; low byte cel_status_mat = bits, U08, 87, [1:1] cel_status_clt = bits, U08, 87, [2:2] cel_status_tps = bits, U08, 87, [3:3] cel_status_batt = bits, U08, 87, [4:4] cel_status_afr0 = bits, U08, 87, [5:5] cel_status_sync = bits, U08, 87, [6:6] cel_status_egt = bits, U08, 87, [7:7] cel_status_flex = bits, U08, 86, [0:0] ; high byte cel_status_maf = bits, U08, 86, [1:1] ; high byte cel_status_knock = bits, U08, 86, [2:2] ; high byte cel_status_cam = bits, U08, 86, [3:3] ; high byte cel_status_oil = bits, U08, 86, [4:4] ; high byte cel_status_fp = bits, U08, 86, [5:5] ; high byte cel_status_egtshut= bits, U08, 86, [6:6] ; high byte cel_status_afrshut= bits, U08, 86, [7:7] ; high byte fuelload2 = scalar, S16, 88, { bitStringValue( algorithmUnits , algorithm2 ) }, 0.100, 0.0 ignload = scalar, S16, 90, "%", 0.100, 0.0 ignload2 = scalar, S16, 92, "%", 0.100, 0.0 synccnt = scalar, U08, 94, "", 1, 0 syncreason = scalar, U08, 95, "", 1.0, 0.0 wallfuel1 = scalar, U32, 96, "uS", 0.010, 0.0 wallfuel2 = scalar, U32, 100, "uS", 1.000, 0.0 sensor01 = scalar, S16, 104, "", 0.1000, 0.0 sensor02 = scalar, S16, 106, "", 0.1000, 0.0 sensor03 = scalar, S16, 108, "", 0.1000, 0.0 sensor04 = scalar, S16, 110, "", 0.1000, 0.0 sensor05 = scalar, S16, 112, "", 0.1000, 0.0 sensor06 = scalar, S16, 114, "", 0.1000, 0.0 sensor07 = scalar, S16, 116, "", 0.1000, 0.0 sensor08 = scalar, S16, 118, "", 0.1000, 0.0 sensor09 = scalar, S16, 120, "", 0.1000, 0.0 sensor10 = scalar, S16, 122, "", 0.1000, 0.0 sensor11 = scalar, S16, 124, "", 0.1000, 0.0 sensor12 = scalar, S16, 126, "", 0.1000, 0.0 sensor13 = scalar, S16, 128, "", 0.1000, 0.0 sensor14 = scalar, S16, 130, "", 0.1000, 0.0 sensor15 = scalar, S16, 132, "", 0.1000, 0.0 sensor16 = scalar, S16, 134, "", 0.1000, 0.0 canin1_8 = scalar, U08, 136, "", 1.000, 0.0 canout1_8 = scalar, U08, 137, "", 1.000, 0.0 canout9_16 = scalar, U08, 138, "", 1.000, 0.0 boostduty = scalar, U08, 139 , "%", 1.0, 0.0 #if PW_4X n2o_addfuel = scalar, S16, 140, "ms", 0.004, 0 #else n2o_addfuel = scalar, S16, 140, "ms", 0.001, 0 #endif n2o_retard = scalar, S16, 142, "deg", 0.1, 0 #if PW_4X pwseq1 = scalar, U16, 144, "ms", 0.004, 0.0 pwseq2 = scalar, U16, 146, "ms", 0.004, 0.0 pwseq3 = scalar, U16, 148, "ms", 0.004, 0.0 pwseq4 = scalar, U16, 150, "ms", 0.004, 0.0 pwseq5 = scalar, U16, 152, "ms", 0.004, 0.0 pwseq6 = scalar, U16, 154, "ms", 0.004, 0.0 pwseq7 = scalar, U16, 156, "ms", 0.004, 0.0 pwseq8 = scalar, U16, 158, "ms", 0.004, 0.0 pwseq9 = scalar, U16, 160, "ms", 0.004, 0.0 pwseq10 = scalar, U16, 162, "ms", 0.004, 0.0 pwseq11 = scalar, U16, 164, "ms", 0.004, 0.0 pwseq12 = scalar, U16, 166, "ms", 0.004, 0.0 pwseq13 = scalar, U16, 168, "ms", 0.004, 0.0 pwseq14 = scalar, U16, 170, "ms", 0.004, 0.0 pwseq15 = scalar, U16, 172, "ms", 0.004, 0.0 pwseq16 = scalar, U16, 174, "ms", 0.004, 0.0 #else pwseq1 = scalar, U16, 144, "ms", 0.001, 0.0 pwseq2 = scalar, U16, 146, "ms", 0.001, 0.0 pwseq3 = scalar, U16, 148, "ms", 0.001, 0.0 pwseq4 = scalar, U16, 150, "ms", 0.001, 0.0 pwseq5 = scalar, U16, 152, "ms", 0.001, 0.0 pwseq6 = scalar, U16, 154, "ms", 0.001, 0.0 pwseq7 = scalar, U16, 156, "ms", 0.001, 0.0 pwseq8 = scalar, U16, 158, "ms", 0.001, 0.0 pwseq9 = scalar, U16, 160, "ms", 0.001, 0.0 pwseq10 = scalar, U16, 162, "ms", 0.001, 0.0 pwseq11 = scalar, U16, 164, "ms", 0.001, 0.0 pwseq12 = scalar, U16, 166, "ms", 0.001, 0.0 pwseq13 = scalar, U16, 168, "ms", 0.001, 0.0 pwseq14 = scalar, U16, 170, "ms", 0.001, 0.0 pwseq15 = scalar, U16, 172, "ms", 0.001, 0.0 pwseq16 = scalar, U16, 174, "ms", 0.001, 0.0 #endif nitrous1_duty = scalar, U08, 176, "%", 1, 0 nitrous2_duty = scalar, U08, 177, "%", 1, 0 #if CELSIUS egt1 = scalar, S16, 178, "°C", 0.05555, -320 egt2 = scalar, S16, 180, "°C", 0.05555, -320 egt3 = scalar, S16, 182, "°C", 0.05555, -320 egt4 = scalar, S16, 184, "°C", 0.05555, -320 egt5 = scalar, S16, 186, "°C", 0.05555, -320 egt6 = scalar, S16, 188, "°C", 0.05555, -320 egt7 = scalar, S16, 190, "°C", 0.05555, -320 egt8 = scalar, S16, 192, "°C", 0.05555, -320 egt9 = scalar, S16, 194, "°C", 0.05555, -320 egt10 = scalar, S16, 196, "°C", 0.05555, -320 egt11 = scalar, S16, 198, "°C", 0.05555, -320 egt12 = scalar, S16, 200, "°C", 0.05555, -320 egt13 = scalar, S16, 202, "°C", 0.05555, -320 egt14 = scalar, S16, 204, "°C", 0.05555, -320 egt15 = scalar, S16, 206, "°C", 0.05555, -320 egt16 = scalar, S16, 208, "°C", 0.05555, -320 #else egt1 = scalar, S16, 178, "°F", 0.1, 0 egt2 = scalar, S16, 180, "°F", 0.1, 0 egt3 = scalar, S16, 182, "°F", 0.1, 0 egt4 = scalar, S16, 184, "°F", 0.1, 0 egt5 = scalar, S16, 186, "°F", 0.1, 0 egt6 = scalar, S16, 188, "°F", 0.1, 0 egt7 = scalar, S16, 190, "°F", 0.1, 0 egt8 = scalar, S16, 192, "°F", 0.1, 0 egt9 = scalar, S16, 194, "°F", 0.1, 0 egt10 = scalar, S16, 196, "°F", 0.1, 0 egt11 = scalar, S16, 198, "°F", 0.1, 0 egt12 = scalar, S16, 200, "°F", 0.1, 0 egt13 = scalar, S16, 202, "°F", 0.1, 0 egt14 = scalar, S16, 204, "°F", 0.1, 0 egt15 = scalar, S16, 206, "°F", 0.1, 0 egt16 = scalar, S16, 208, "°F", 0.1, 0 #endif maf = scalar, U16, 210, "g/sec", { 0.010 * (maf_range + 1) }, 0.0 canpwmin0 = scalar, U16, 212, "", 1.000, 0.0 canpwmin1 = scalar, U16, 214, "", 1.000, 0.0 canpwmin2 = scalar, U16, 216, "", 1.000, 0.0 canpwmin3 = scalar, U16, 218, "", 1.000, 0.0 fuelflow = scalar, U16, 220, "cc/min", 1, 0.0 fuelcons = scalar, U16, 222, "l/km", 1, 0.0 EAEFuelCorr2 = scalar, U16, 224 , "%", 1.0, 0.0 tpsADC = scalar, U16, 226, "ADC", 1, 0 ; REAL for calibrator eaeload1 = scalar, S16, 228, { bitStringValue( algorithmUnits , (eaeload ? eaeload : algorithm) ) }, 0.1000, 0.0 afrload1 = scalar, S16, 230, { bitStringValue( algorithmUnits , (afrload ? afrload : algorithm) ) }, 0.1000, 0.0 gear = scalar, U08, 232, "", 1, 0 timing_err = scalar, S08, 233, "%", 1, 0 ; accuracy of timing prediction RPMdot = scalar, S16, 234, "rpm/sec", 10, 0 vss1dot = scalar, S16, 236, "ms-2", 0.1, 0 vss2dot = scalar, S16, 238, "ms-2", 0.1, 0 accelx = scalar, S16, 240, "ms-2", 0.001, 0 accely = scalar, S16, 242, "ms-2", 0.001, 0 accelz = scalar, S16, 244, "ms-2", 0.001, 0 duty_pwm_a = scalar, U08, 246, "%", 1, 0 duty_pwm_b = scalar, U08, 247, "%", 1, 0 duty_pwm_c = scalar, U08, 248, "%", 1, 0 duty_pwm_d = scalar, U08, 249, "%", 1, 0 duty_pwm_e = scalar, U08, 250, "%", 1, 0 duty_pwm_f = scalar, U08, 251, "%", 1, 0 afr1 = scalar, U08, 252, "AFR", 0.1, 0.0 afr2 = scalar, U08, 253, "AFR", 0.1, 0.0 afr3 = scalar, U08, 254, "AFR", 0.1, 0.0 afr4 = scalar, U08, 255, "AFR", 0.1, 0.0 afr5 = scalar, U08, 256, "AFR", 0.1, 0.0 afr6 = scalar, U08, 257, "AFR", 0.1, 0.0 afr7 = scalar, U08, 258, "AFR", 0.1, 0.0 afr8 = scalar, U08, 259, "AFR", 0.1, 0.0 afr9 = scalar, U08, 260, "AFR", 0.1, 0.0 afr10 = scalar, U08, 261, "AFR", 0.1, 0.0 afr11 = scalar, U08, 262, "AFR", 0.1, 0.0 afr12 = scalar, U08, 263, "AFR", 0.1, 0.0 afr13 = scalar, U08, 264, "AFR", 0.1, 0.0 afr14 = scalar, U08, 265, "AFR", 0.1, 0.0 afr15 = scalar, U08, 266, "AFR", 0.1, 0.0 afr16 = scalar, U08, 267, "AFR", 0.1, 0.0 egov1 = scalar, U16, 268, "V", 0.00489, 0.0 egov2 = scalar, U16, 270, "V", 0.00489, 0.0 egov3 = scalar, U16, 272, "V", 0.00489, 0.0 egov4 = scalar, U16, 274, "V", 0.00489, 0.0 egov5 = scalar, U16, 276, "V", 0.00489, 0.0 egov6 = scalar, U16, 278, "V", 0.00489, 0.0 egov7 = scalar, U16, 280, "V", 0.00489, 0.0 egov8 = scalar, U16, 282, "V", 0.00489, 0.0 egov9 = scalar, U16, 284, "V", 0.00489, 0.0 egov10 = scalar, U16, 286, "V", 0.00489, 0.0 egov11 = scalar, U16, 288, "V", 0.00489, 0.0 egov12 = scalar, U16, 290, "V", 0.00489, 0.0 egov13 = scalar, U16, 292, "V", 0.00489, 0.0 egov14 = scalar, U16, 294, "V", 0.00489, 0.0 egov15 = scalar, U16, 296, "V", 0.00489, 0.0 egov16 = scalar, U16, 298, "V", 0.00489, 0.0 egocor1 = scalar, S16, 300, "%", 0.1000, 0.0 egocor2 = scalar, S16, 302, "%", 0.1000, 0.0 egocor3 = scalar, S16, 304, "%", 0.1000, 0.0 egocor4 = scalar, S16, 306, "%", 0.1000, 0.0 egocor5 = scalar, S16, 308, "%", 0.1000, 0.0 egocor6 = scalar, S16, 310, "%", 0.1000, 0.0 egocor7 = scalar, S16, 312, "%", 0.1000, 0.0 egocor8 = scalar, S16, 314, "%", 0.1000, 0.0 egocor9 = scalar, S16, 316, "%", 0.1000, 0.0 egocor10 = scalar, S16, 318, "%", 0.1000, 0.0 egocor11 = scalar, S16, 320, "%", 0.1000, 0.0 egocor12 = scalar, S16, 322, "%", 0.1000, 0.0 egocor13 = scalar, S16, 324, "%", 0.1000, 0.0 egocor14 = scalar, S16, 326, "%", 0.1000, 0.0 egocor15 = scalar, S16, 328, "%", 0.1000, 0.0 egocor16 = scalar, S16, 330, "%", 0.1000, 0.0 stream_level = scalar, U08, 332, "", 1,0 water_duty = scalar, U08, 333, "%", 1, 0 dwell_trl = scalar, U16, 334, "ms", 0.1000, 0.0 vss1 = scalar, U16, 336, { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, { msToPrefUnitsScale }, 0.0 vss2 = scalar, U16, 338, { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, { msToPrefUnitsScale }, 0.0 vss1_ms_1 = scalar, U16, 336, "ms-1", 0.1, 0.0 ; see calcs converting this raw number into kph or mph vss2_ms_1 = scalar, U16, 338, "ms-1", 0.1, 0.0 ss1 = scalar, U16, 340, "RPM", 10.000, 0.0 ; now in steps of 10 rpm ss2 = scalar, U16, 342, "RPM", 10.000, 0.0 nitrous_timer = scalar, U16, 344, "s", 0.001, 0 sd_filenum = scalar, U16, 346, "", 1, 0 sd_error = scalar, U08, 348, "", 1, 0 sd_phase = scalar, U08, 349, "", 1, 0 boostduty2 = scalar, U08, 350 , "%", 1.0, 0.0 status8 = scalar, U08, 351, "", 1.0, 0.0 vvt_ang1 = scalar, S16, 352, "deg", 0.100, 0.0 vvt_ang2 = scalar, S16, 354, "deg", 0.100, 0.0 vvt_ang3 = scalar, S16, 356, "deg", 0.100, 0.0 vvt_ang4 = scalar, S16, 358, "deg", 0.100, 0.0 inj_timing_pri = scalar, S16, 360, "deg", 0.100, 0.0 inj_timing_sec = scalar, S16, 362, "deg", 0.100, 0.0 vvt_target1 = scalar, S16, 364, "deg", 0.100, 0.0 vvt_target2 = scalar, S16, 366, "deg", 0.100, 0.0 vvt_target3 = scalar, S16, 368, "deg", 0.100, 0.0 vvt_target4 = scalar, S16, 370, "deg", 0.100, 0.0 vvt_duty1 = scalar, U08, 372 , "%", 0.392, 0.0 vvt_duty2 = scalar, U08, 373 , "%", 0.392, 0.0 vvt_duty3 = scalar, U08, 374 , "%", 0.392, 0.0 vvt_duty4 = scalar, U08, 375 , "%", 0.392, 0.0 fuel_pct = scalar, U16, 376, "%", 0.1000, 0.0 #if CELSIUS fuel_temp1 = scalar, S16, 378, "°C", 0.05555, -320.0 fuel_temp2 = scalar, S16, 380, "°C", 0.05555, -320.0 #else fuel_temp1 = scalar, S16, 378, "°F", 0.100, 0.0 fuel_temp2 = scalar, S16, 380, "°C", 0.05555, -320.0 #endif tps_accel = scalar, S16, 382, "%", 0.1000, 0.0 map_accel = scalar, S16, 384, "%", 0.1000, 0.0 total_accel = scalar, S16, 386, "%", 0.1000, 0.0 knock_cyl01 = scalar, U08, 388, "%", 0.4, 0 knock_cyl02 = scalar, U08, 389, "%", 0.4, 0 knock_cyl03 = scalar, U08, 390, "%", 0.4, 0 knock_cyl04 = scalar, U08, 391, "%", 0.4, 0 knock_cyl05 = scalar, U08, 392, "%", 0.4, 0 knock_cyl06 = scalar, U08, 393, "%", 0.4, 0 knock_cyl07 = scalar, U08, 394, "%", 0.4, 0 knock_cyl08 = scalar, U08, 395, "%", 0.4, 0 knock_cyl09 = scalar, U08, 396, "%", 0.4, 0 knock_cyl10 = scalar, U08, 397, "%", 0.4, 0 knock_cyl11 = scalar, U08, 398, "%", 0.4, 0 knock_cyl12 = scalar, U08, 399, "%", 0.4, 0 knock_cyl13 = scalar, U08, 400, "%", 0.4, 0 knock_cyl14 = scalar, U08, 401, "%", 0.4, 0 knock_cyl15 = scalar, U08, 402, "%", 0.4, 0 knock_cyl16 = scalar, U08, 403, "%", 0.4, 0 launch_timer = scalar, U16, 404, "s", 0.001, 0 launch_retard = scalar, S16, 406, "deg", 0.1, 0 maf_volts = scalar, U16, 408, "V", 0.001, 0.0 porta = scalar, U08, 410, "bit", 1.000, 0.0 ; raw i/o port status bits porta0 = bits, U08, 410, [0:0] porta1 = bits, U08, 410, [1:1] porta2 = bits, U08, 410, [2:2] porta3 = bits, U08, 410, [3:3] porta4 = bits, U08, 410, [4:4] porta5 = bits, U08, 410, [5:5] porta6 = bits, U08, 410, [6:6] porta7 = bits, U08, 410, [7:7] portb = scalar, U08, 411, "bit", 1.000, 0.0 ; raw i/o port status bits portb0 = bits, U08, 411, [0:0] portb1 = bits, U08, 411, [1:1] portb2 = bits, U08, 411, [2:2] portb3 = bits, U08, 411, [3:3] portb4 = bits, U08, 411, [4:4] portb5 = bits, U08, 411, [5:5] portb6 = bits, U08, 411, [6:6] portb7 = bits, U08, 411, [7:7] porteh = scalar, U08, 412, "bit", 1.000, 0.0 ; raw i/o port status bits porte0 = bits, U08, 412, [0:0] porte1 = bits, U08, 412, [1:1] porte2 = bits, U08, 412, [2:2] porte4 = bits, U08, 412, [4:4] porth6 = bits, U08, 412, [6:6] porth7 = bits, U08, 412, [7:7] portk = scalar, U08, 413, "bit", 1.000, 0.0 ; raw i/o port status bits portk0 = bits, U08, 413, [0:0] portk1 = bits, U08, 413, [1:1] portk2 = bits, U08, 413, [2:2] portk3 = bits, U08, 413, [3:3] portk7 = bits, U08, 413, [7:7] portmj = scalar, U08, 414, "bit", 1.000, 0.0 ; raw i/o port status bits portj0 = bits, U08, 414, [0:0] portj1 = bits, U08, 414, [1:1] portm2 = bits, U08, 414, [2:2] portm3 = bits, U08, 414, [3:3] portm4 = bits, U08, 414, [4:4] portm5 = bits, U08, 414, [5:5] portj7 = bits, U08, 414, [7:7] portp = scalar, U08, 415, "bit", 1.000, 0.0 ; raw i/o port status bits portp2 = bits, U08, 415, [2:2] portp3 = bits, U08, 415, [3:3] portp4 = bits, U08, 415, [4:4] portp5 = bits, U08, 415, [5:5] portp6 = bits, U08, 415, [6:6] portp7 = bits, U08, 415, [7:7] portt = scalar, U08, 416, "bit", 1.000, 0.0 ; raw i/o port status bits portt0 = bits, U08, 416, [0:0] portt1 = bits, U08, 416, [1:1] portt2 = bits, U08, 416, [2:2] portt3 = bits, U08, 416, [3:3] portt4 = bits, U08, 416, [4:4] portt5 = bits, U08, 416, [5:5] portt6 = bits, U08, 416, [6:6] cel_errorcode = scalar, U08, 417, "bit", 1, 0.0 boost_targ_1 = scalar, S16, 418, "%", 0.1, 0 boost_targ_2 = scalar, S16, 420, "%", 0.1, 0 #if CELSIUS airtemp = scalar, S16, 422, "°C", 0.05555, -320.0 #else airtemp = scalar, S16, 422, "°F", 0.100, 0.0 #endif looptime = scalar, U16, 424, "us", 1.0, 0.0 vss3 = scalar, U16, 426, { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, { msToPrefUnitsScale }, 0.0 vss4 = scalar, U16, 428, { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, { msToPrefUnitsScale }, 0.0 vss3_ms_1 = scalar, U16, 426, "ms-1", 0.1, 0.0 vss4_ms_1 = scalar, U16, 428, "ms-1", 0.1, 0.0 fuel_press1 = scalar, S16, 430, "kPa", 0.100, 0.0 fuel_press2 = scalar, S16, 432, "kPa", 0.100, 0.0 cl_idle_targ_rpm = scalar, U16, 434, "rpm", 1, 0 fp_duty = scalar, U08, 436, "%", 0.392, 0.0 alt_duty = scalar, U08, 437, "%", 1, 0.0 alt_freq = scalar, U08, 437, "Hz", 1, 0.0 load_duty = scalar, U08, 438, "%", 1, 0.0 alt_targv = scalar, U08, 439, "V", 0.100, 0.0 batt_curr = scalar, S16, 440, "A", 0.1, 0.0 fueltemp_cor = scalar, S16, 442, "%", 0.100, 0.0 fuelpress_cor = scalar, S16, 444, "%", 0.100, 0.0 ltt_cor = scalar, S08, 446, "%", 0.100, 0.0 ; gap 447 tc_retard = scalar, S16, 448, "deg", 0.100, 0.0 cel_retard = scalar, S16, 450, "deg", 0.100, 0.0 fc_retard = scalar, S16, 452, "deg", 0.100, 0.0 ext_advance = scalar, S16, 454, "deg", 0.100, 0.0 base_advance = scalar, S16, 456, "deg", 0.100, 0.0 idle_cor_advance = scalar, S16, 458, "deg", 0.100, 0.0 mat_retard = scalar, S16, 460, "deg", 0.100, 0.0 flex_advance = scalar, S16, 462, "deg", 0.100, 0.0 adv1 = scalar, S16, 464, "deg", 0.100, 0.0 adv2 = scalar, S16, 466, "deg", 0.100, 0.0 adv3 = scalar, S16, 468, "deg", 0.100, 0.0 adv4 = scalar, S16, 470, "deg", 0.100, 0.0 revlim_retard = scalar, S16, 472, "deg", 0.100, 0.0 als_timing = scalar, S16, 474, "deg", 0.100, 0.0 #if PW_4X als_addfuel = scalar, S16, 476, "ms", 0.004, 0.0 deadtime1 = scalar, S16, 478, "ms", 0.004, 0.0 #else als_addfuel = scalar, S16, 476, "ms", 0.001, 0.0 deadtime1 = scalar, S16, 478, "ms", 0.001, 0.0 #endif launch_timing = scalar, S16, 480, "deg", 0.100, 0.0 step3_timing = scalar, S16, 482, "deg", 0.100, 0.0 launchvss_retard = scalar, S16, 484, "deg", 0.100, 0.0 ; cel_status2_xx = bits, U08, 486, [0:0] ; high byte cel_status2 = scalar, U16, 486, "bit", 1.000, 0.0 ; engine fault bits cel_status2_winj = bits, U08, 487, [0:0] ; low byte cel_status2_shutd = bits, U08, 487, [1:1] gps_latdeg = scalar, S08, 488, "", 1,0 gps_latmin = scalar, U08, 489, "", 1,0 gps_latmmin = scalar, U16, 490, "", 1,0 gps_londeg = scalar, U08, 492, "", 1,0 gps_lonmin = scalar, U08, 493, "", 1,0 gps_lonmmin = scalar, U16, 494, "", 1,0 gps_outstatus = scalar, U08, 496, "", 1,0 gps_altk = scalar, S08, 497, "", 1,0 gps_altm = scalar, S16, 498, "", 0.1,0 gps_speed = scalar, U16, 500, { bitStringValue( prefSpeedUnits , prefSpeedUnits ) }, { msToPrefUnitsScale }, 0.0 gps_speed_ms_1 = scalar, U16, 500, "ms-1", 0.1, 0.0 gps_course = scalar, U16, 502, "", 0.1,0 generic_pid_duty_a = scalar, U08, 504, "%", 0.392, 0.0 generic_pid_duty_b = scalar, U08, 505, "%", 0.392, 0.0 ;very nearly out of space. 512+ requires firmware changes ;--------------- accDecEnrich = { (pulseWidth1 > 0) ? (((accEnrichMS + decEnrichMS)/pulseWidth1*100) + 100) : 100 }, "%" accDecEnrichPcnt = { (pulseWidth1 > 0) ? (accelEnrich/pulseWidth1 + (tpsaccden ? tpsfuelcut : accelEnrich/pulseWidth1*100)) : 100 }, "%" accEnrichPcnt = { (pulseWidth1 > 0) ? (100 + (accelEnrich/pulseWidth1*100)) : 100 }, "%" accEnrichMS = { accelEnrich }, "ms" decEnrichPcnt = { (tpsaccden ? tpsfuelcut : 100) }, "%" decEnrichMS = { (pulseWidth1 > 0) ? ((tpsfuelcut/100*pulseWidth1)-pulseWidth1) : 100 }, "ms" ; approximation because doesn't include deadtime time = { timeNow }, "s" rpm100 = { rpm / 100.0 } cycleTime1 = { rpm ? (60000.0 / rpm * (2.0-(twoStroke&1))) : 0 }, "ms" nSquirts1 = { nCylinders/divider} altDiv1 = { alternate ? 2 : 1 } dcfactor1 = { (sequential == 0) ? nSquirts1/altDiv1 : ( (sequential == 1) ? 2 : 1) } dutyCycle1 = { cycleTime1 ? (100.0*dcfactor1*pulseWidth1/cycleTime1) : 0}, "%" cycleTime2 = { rpm ? (60000.0 / rpm * (2.0-(twoStroke&1))) : 0 }, "ms" nSquirts2 = { nCylinders/divider } altDiv2 = { alternate ? 2 : 1 } ; ought to look at staging parameters too dcfactor2a = { (sequential == 0) ? nSquirts2/altDiv2 : ( (sequential == 1) ? 2 : 1) } ; ought to look at staging parameters too dcfactor2b = { (staged_first_param && staged_extended_opts_use_v3) ? 1 : dcfactor2a } dutyCycle2 = { cycleTime2 ? (100.0*dcfactor2b*pulseWidth2/cycleTime2) : 0}, "%" #if NARROW_BAND_EGO egoVoltage = { egoV }, "V" ; For LED bars... afr1err = { egov1 - afrtgt1 } afr2err = { egov2 - afrtgt2 } #elif LAMBDA lambda1 = { afr1 / stoich }, "Lambda" lambda2 = { afr2 / stoich }, "Lambda2" lambda3 = { afr3 / stoich }, "Lambda3" lambda4 = { afr4 / stoich }, "Lambda4" lambda5 = { afr5 / stoich }, "Lambda5" lambda6 = { afr6 / stoich }, "Lambda6" lambda7 = { afr7 / stoich }, "Lambda7" lambda8 = { afr8 / stoich }, "Lambda8" egoVoltage = { lambda1 }, "Lambda" ; For LED bars... afrtgt1 = { afrtgt1raw / stoich * (egoType == 2) } ; return zero if NB because of mixed units with target in volts afrtgt2 = { afrtgt2raw / stoich * (egoType == 2) } afr1err = { (afr1 - afrtgt1raw) / stoich * (egoType == 2)} afr2err = { (afr2 - afrtgt2raw) / stoich * (egoType == 2)} #else egoVoltage = { afr1 }, "AFR" ; For LED bars... afr1err = { afr1 - afrtgt1 } afr2err = { afr2 - afrtgt2 } #endif pwma_load = { getChannelValueByOffset( pwm_opt_load_a_offset ) } pwmb_load = { getChannelValueByOffset( pwm_opt_load_b_offset ) } pwmc_load = { getChannelValueByOffset( pwm_opt_load_c_offset ) } pwmd_load = { getChannelValueByOffset( pwm_opt_load_d_offset ) } pwme_load = { getChannelValueByOffset( pwm_opt_load_e_offset ) } pwmf_load = { getChannelValueByOffset( pwm_opt_load_f_offset ) } maxafrload = { (maxafr_opt1_load & 1) ? tps : map } vvt_load = { (vvt_opt7_yaxis == 0) ? fuelload : ((vvt_opt7_yaxis == 1) ? map : ( (vvt_opt7_yaxis == 2) ? (map*100/barometer) : ((vvt_opt7_yaxis == 3) ? tps : ((vvt_opt7_yaxis == 4) ? mafload : fuelload ) ) ) ) } reqfuel = { reqFuel } Stoich = { stoich } ; Vacuum and Boost Gauges boostbar = { (map - barometer) / 101.33} boostpsig = { (map - barometer) * 0.1450} vacuum = { (barometer-map)*0.2953007 } ; Calculate vacuum in in-Hg. boostvac = { map < barometer ? -vacuum : boostpsig } ; calculate instantaneous economy from fuel flow (not calculated in firmware at this time) economy_l_km = { vss1_ms_1 ? (fuelflow / (vss1_ms_1 * 60)) : 0 } ; economy_mpg_us = { (1 / economy_l_km) * 3.800 / 1.609344 } economy_mpg_us = { vss1_ms_1 ? (2.361 / economy_l_km) : 0 } economy_mpg_uk = { vss1_ms_1 ? (2.825 / economy_l_km) : 0 } economy_l_100km = { economy_l_km * 100 } pwmidle_cl_initialvalue_matorclt_follower = { pwmidle_cl_opts_initval_clt ? coolant : mat } rpm_target_error_follower = { rpm - cl_idle_targ_rpm }, "rpm" #if CELSIUS cltlowlim = { clt_exp ? -40 : -40 } clthighlim = { clt_exp ? 230 : 120 } cltlowdang = { clt_exp ? 65 : 10 } cltlowwarn = { clt_exp ? 93 : 65 } clthighwarn = { clt_exp ? 162 : 93 } clthighdang = { clt_exp ? 176 : 104 } mathigh = { 110 } #else ; fahrenheit cltlowlim = { clt_exp ? -40 : -40 } clthighlim = { clt_exp ? 450 : 250 } cltlowdang = { clt_exp ? 150 : 50 } cltlowwarn = { clt_exp ? 200 : 150 } clthighwarn = { clt_exp ? 325 : 200 } clthighdang = { clt_exp ? 350 : 220 } mathigh = { 215 } #endif ;synthetic air flow calcflow = { fuelload * rpm * veCurr1/100 } maf_freq = { MAFOption_t ? (maf_freq0 + ((maf_freq1 - maf_freq0) * maf_volts / 5)) : 0 } ;old names tpsDOT = { TPSdot } mapDOT = { MAPdot } ;fuel pressures fuel_press1_psi = {fuel_press1 * 0.147 }, "psi" fuel_press2_psi = {fuel_press2 * 0.147 }, "psi" fuel_press1_bar = {fuel_press1 / 101.35 }, "bar" fuel_press2_bar = {fuel_press2 / 101.35 }, "bar" msToPrefUnitsScale = { prefSpeedUnits == 0 ? 0.22369 : 0.36 }, "" gps_latsec = { 60 * gps_latmmin / 10000 } gps_lonsec = { 60 * gps_lonmmin / 10000 } gps_alt = { gps_altk * 1000 + gps_altm } gps_latitude = { gps_latdeg + (gps_latmin / 60) + (gps_latsec / 3600) } gps_long = { gps_londeg + (gps_lonmin / 60) + (gps_lonsec / 3600) } gps_lonEW = { (gps_outstatus & 1) ? 1 : 0 } gps_longitude = { gps_lonEW ? 0-gps_long : gps_long } ; the 0 is redundant, but causes a TS error otherwise generic_pid_load_a = { getChannelValueByOffset( generic_pid_load_offset_a ) } generic_pid_load_b = { getChannelValueByOffset( generic_pid_load_offset_b ) } ;------------------------------------------------------------------------------- ;-- The entries are saved in the datalog file in the order in which they -- ;-- appear in the list below. -- ;-- -- ;-- Channel - Case sensitive name of output channel to be logged. -- ;-- Label - String written to header line of log. -- ;-- Type - Data type of output, converted before writing. -- ;-- Format - C-style output format of data. -- [Datalog] ; Channel Label Type Format ; -------------- ---------- ----- ------ entry = time, "Time", float, "%.3f" entry = seconds, "SecL", int, "%d" entry = rpm, "RPM", int, "%d" entry = map, "MAP", float, "%.1f" entry = boostpsig, "Boost psi", float, "%.1f" entry = throttle, "TPS", float, "%.1f" entry = tpsADC, "TPSADC", int, "%d" ; for debug entry = maf, "MAF", float, "%.2f", { MAFOption || MAFOption_t } entry = mafload, "MAFload", float, "%.1f", { MAFOption || MAFOption_t } entry = maf_volts, "MAF volts", float, "%.3f", { MAFOption } entry = maf_freq, "MAF Freq", int, "%d", { MAFOption_t } #if NARROW_BAND_EGO entry = egov1 , "O2", float, "%.3f", {egonum > 0} entry = egov2 , "O2 #2", float, "%.3f", {egonum > 1} entry = egov3 , "O2 #3", float, "%.3f", {egonum > 2} entry = egov4 , "O2 #4", float, "%.3f", {egonum > 3} entry = egov5 , "O2 #5", float, "%.3f", {egonum > 4} entry = egov6 , "O2 #6", float, "%.3f", {egonum > 5} entry = egov7 , "O2 #7", float, "%.3f", {egonum > 6} entry = egov8 , "O2 #8", float, "%.3f", {egonum > 7} #elif LAMBDA entry = lambda1, "Lambda", float, "%.3f", {egonum > 0} entry = lambda2, "Lambda2", float, "%.3f", {egonum > 1} entry = lambda3, "Lambda3", float, "%.3f", {egonum > 2} entry = lambda4, "Lambda4", float, "%.3f", {egonum > 3} entry = lambda5, "Lambda5", float, "%.3f", {egonum > 4} entry = lambda6, "Lambda6", float, "%.3f", {egonum > 5} entry = lambda7, "Lambda7", float, "%.3f", {egonum > 6} entry = lambda8, "Lambda8", float, "%.3f", {egonum > 7} #else entry = afr1, "AFR", float, "%.2f", {egonum > 0} entry = afr2, "AFR2", float, "%.2f", {egonum > 1} entry = afr3, "AFR3", float, "%.2f", {egonum > 2} entry = afr4, "AFR4", float, "%.2f", {egonum > 3} entry = afr5, "AFR5", float, "%.2f", {egonum > 4} entry = afr6, "AFR6", float, "%.2f", {egonum > 5} entry = afr7, "AFR7", float, "%.2f", {egonum > 6} entry = afr8, "AFR8", float, "%.2f", {egonum > 7} #endif entry = mat, "MAT", float, "%.1f" entry = coolant, "CLT", float, "%.1f" entry = engine, "Engine", int, "%d" entry = batteryVoltage, "Batt V", float, "%.1f" entry = egocor1, "EGO cor1", int, "%.1f" entry = egocor2, "EGO cor2", int, "%.1f", {egonum > 1} entry = egocor3, "EGO cor3", int, "%.1f", {egonum > 2} entry = egocor4, "EGO cor4", int, "%.1f", {egonum > 3} entry = egocor5, "EGO cor5", int, "%.1f", {egonum > 4} entry = egocor6, "EGO cor6", int, "%.1f", {egonum > 5} entry = egocor7, "EGO cor7", int, "%.1f", {egonum > 6} entry = egocor8, "EGO cor8", int, "%.1f", {egonum > 7} entry = airCorrection, "Fuel: Air cor", int, "%.1f" entry = warmupEnrich, "Fuel: Warmup cor", int, "%d" entry = baroCorrection, "Fuel: Baro cor", int, "%.1f" entry = gammaEnrich, "Fuel: Total cor", int, "%d" entry = accDecEnrich, "Fuel: Accel enrich", int, "%d" entry = accEnrichMS, "Fuel: Accel PW", float, "%.3f" entry = veCurr1, "VE1", int, "%.1f" entry = pulseWidth1, "PW", float, "%.3f" entry = dutyCycle1, "Duty Cycle1", float, "%.1f" entry = veCurr2, "VE2", int, "%.1f" entry = pulseWidth2, "PW2", float, "%.3f" entry = dutyCycle2, "Duty Cycle2", float, "%.1f" entry = pwseq1, "Seq PW1", float, "%.3f", { sequential } entry = pwseq2, "Seq PW2", float, "%.3f", { sequential } entry = pwseq3, "Seq PW3", float, "%.3f", { sequential } entry = pwseq4, "Seq PW4", float, "%.3f", { sequential } entry = pwseq5, "Seq PW5", float, "%.3f", { sequential } entry = pwseq6, "Seq PW6", float, "%.3f", { sequential } entry = pwseq7, "Seq PW7", float, "%.3f", { sequential } entry = pwseq8, "Seq PW8", float, "%.3f", { sequential } #if CYL_12_16_SUPPORT entry = pwseq9, "Seq PW9", float, "%.3f", { sequential } entry = pwseq10, "Seq PW10", float, "%.3f", { sequential } entry = pwseq11, "Seq PW11", float, "%.3f", { sequential } entry = pwseq12, "Seq PW12", float, "%.3f", { sequential } entry = pwseq13, "Seq PW13", float, "%.3f", { sequential } entry = pwseq14, "Seq PW14", float, "%.3f", { sequential } entry = pwseq15, "Seq PW15", float, "%.3f", { sequential } entry = pwseq16, "Seq PW16", float, "%.3f", { sequential } #endif entry = advance, "SPK: Spark Advance", float, "%.1f" entry = knockRetard, "SPK: Knock retard", float, "%.1f" entry = knock, "Knock in", float, "%.1f" entry = coldAdvDeg, "SPK: Cold advance", float, "%.1f" entry = tc_retard, "SPK: Traction retard", float, "%.1f" entry = cel_retard, "SPK: CEL retard", float, "%.1f" entry = fc_retard, "SPK: Fuel cut retard", float, "%.1f" entry = ext_advance, "SPK: External advance", float, "%.1f" entry = base_advance, "SPK: Base Spark Advance",float, "%.1f" entry = idle_cor_advance,"SPK: Idle Correction Advance", float, "%.1f" entry = mat_retard, "SPK: MAT Retard", float, "%.1f" entry = flex_advance, "SPK: Flex Advance", float, "%.1f" entry = adv1, "SPK: Spark Table 1", float, "%.1f" entry = adv2, "SPK: Spark Table 2", float, "%.1f" entry = adv3, "SPK: Spark Table 3", float, "%.1f" entry = adv4, "SPK: Spark Table 4", float, "%.1f" entry = revlim_retard, "SPK: Revlim Retard", float, "%.1f" entry = als_timing, "SPK: ALS Timing", float, "%.1f" entry = launch_timing, "SPK: Launch Timing", float, "%.1f" entry = step3_timing, "SPK: 3-step Timing", float, "%.1f" entry = launchvss_retard,"SPK: Launch VSS Retard",float, "%.1f" entry = n2o_retard, "SPK: Nitrous Retard", float, "%.1f", { N2Oopt_2 } entry = dwell, "Dwell", float, "%.2f" entry = barometer, "Barometer", float, "%.1f" entry = iacstep, "Stepper Idle position", int, "%d", {IdleCtl == 3} entry = idleDC, "PWM Idle duty", float, "%.1f", {IdleCtl == 2} entry = cl_idle_targ_rpm, "Closed-loop idle target RPM", int, "%d", { ((IdleCtl > 1) && (IdleCtl_alg == 1)) || idle_special_ops_timing_assist } entry = rpm_target_error_follower, "Closed-loop idle RPM error", int, "%d", { ((IdleCtl > 1) && (IdleCtl_alg == 1)) || idle_special_ops_timing_assist } entry = boostduty, "Boost duty", int, "%d", { boost_ctl_settings_on } entry = boost_targ_1, "Boost target 1", int, "%d", { boost_ctl_settings_on && boost_ctl_settings_cl } entry = boostduty2, "Boost duty 2", int, "%d", { boost_ctl_settings_on && boost_ctl_settings_on2 } entry = boost_targ_2, "Boost target 2", int, "%d", { boost_ctl_settings_on && boost_ctl_settings_cl && boost_ctl_settings_on2 } #if NARROW_BAND_EGO entry = afrtgt1, "EgoV 1 Target", float, "%.1f" entry = afrtgt2, "EgoV 2 Target", float, "%.1f" entry = afr1err, "EgoV 1 Error", float, "%.1f" entry = afr2err, "EgoV 2 Error", float, "%.1f" #elif LAMBDA entry = afrtgt1, "Lambda 1 Target", float, "%.1f" entry = afrtgt2, "Lambda 2 Target", float, "%.1f" entry = afr1err, "Lambda 1 Error", float, "%.1f" entry = afr2err, "Lambda 2 Error", float, "%.1f" #else entry = afrtgt1, "AFR 1 Target", float, "%.1f" entry = afrtgt2, "AFR 2 Target", float, "%.1f" entry = afr1err, "AFR 1 Error", float, "%.1f" entry = afr2err, "AFR 2 Error", float, "%.1f" #endif entry = TPSdot, "TPSdot", float, "%.1f" entry = MAPdot, "MAPdot", float, "%.1f" entry = RPMdot, "RPMdot", int, "%d" entry = wallfuel1, "Wall fuel1", int, "%d", {EAEOption} entry = wallfuel2, "Wall fuel2", int, "%d", {EAEOption} entry = EAEFuelCorr1, "EAE1", int, "%d", {EAEOption} entry = EAEFuelCorr2, "EAE2", int, "%d", {EAEOption} entry = fuelload, "Load", float, "%.1f" entry = fuelload2, "Secondary load", float, "%.1f" entry = ignload, "Ign load", float, "%.1f" entry = ignload2, "Secondary ign load", float, "%.1f" entry = eaeload1, "EAE load", float, "%.1f", {EAEOption} entry = afrload1, "AFR load", float, "%.1f" entry = inj_timing_pri, "Injector timing pri", float, "%.1f" entry = inj_timing_sec, "Injector timing sec", float, "%.1f" entry = egt1, "EGT1", int, "%d", {egt_num > 0} entry = egt2, "EGT2", int, "%d", {egt_num > 1} entry = egt3, "EGT3", int, "%d", {egt_num > 2} entry = egt4, "EGT4", int, "%d", {egt_num > 3} entry = egt5, "EGT5", int, "%d", {egt_num > 4} entry = egt6, "EGT6", int, "%d", {egt_num > 5} entry = egt7, "EGT7", int, "%d", {egt_num > 6} entry = egt8, "EGT8", int, "%d", {egt_num > 7} entry = egt9, "EGT9", int, "%d", {egt_num > 8} entry = egt10, "EGT10", int, "%d", {egt_num > 9} entry = egt11, "EGT11", int, "%d", {egt_num > 10} entry = egt12, "EGT12", int, "%d", {egt_num > 11} entry = egt13, "EGT13", int, "%d", {egt_num > 12} entry = egt14, "EGT14", int, "%d", {egt_num > 13} entry = egt15, "EGT15", int, "%d", {egt_num > 14} entry = egt16, "EGT16", int, "%d", {egt_num > 15} entry = sensor01, { stringValue(sensor01Alias) }, float, "%.1f", { sensor01_source } entry = sensor02, { stringValue(sensor02Alias) }, float, "%.1f", { sensor02_source } entry = sensor03, { stringValue(sensor03Alias) }, float, "%.1f", { sensor03_source } entry = sensor04, { stringValue(sensor04Alias) }, float, "%.1f", { sensor04_source } entry = sensor05, { stringValue(sensor05Alias) }, float, "%.1f", { sensor05_source } entry = sensor06, { stringValue(sensor06Alias) }, float, "%.1f", { sensor06_source } entry = sensor07, { stringValue(sensor07Alias) }, float, "%.1f", { sensor07_source } entry = sensor08, { stringValue(sensor08Alias) }, float, "%.1f", { sensor08_source } entry = sensor09, { stringValue(sensor09Alias) }, float, "%.1f", { sensor09_source } entry = sensor10, { stringValue(sensor10Alias) }, float, "%.1f", { sensor10_source } entry = sensor11, { stringValue(sensor11Alias) }, float, "%.1f", { sensor11_source } entry = sensor12, { stringValue(sensor12Alias) }, float, "%.1f", { sensor12_source } entry = sensor13, { stringValue(sensor13Alias) }, float, "%.1f", { sensor13_source } entry = sensor14, { stringValue(sensor14Alias) }, float, "%.1f", { sensor14_source } entry = sensor15, { stringValue(sensor15Alias) }, float, "%.1f", { sensor15_source } entry = sensor16, { stringValue(sensor16Alias) }, float, "%.1f", { sensor16_source } entry = canpwmin0, "CANpwmin0", int, "%d", { enable_pollPWM } entry = canpwmin1, "CANpwmin1", int, "%d", { enable_pollPWM } entry = canpwmin2, "CANpwmin2", int, "%d", { enable_pollPWM } entry = canpwmin3, "CANpwmin3", int, "%d", { enable_pollPWM } entry = timing_err, "Timing err", float, "%.1f" entry = synccnt, "Lost sync count", int, "%d" entry = syncreason, "Lost sync reason", int, "%d" entry = fuelflow, "Fuel flow cc/min", int, "%d" entry = vss1, "VSS1", int, "%.1f", {vss_opt0_1} entry = vss2, "VSS2", int, "%.1f", {vss_opt0_2} entry = vss3, "VSS3", int, "%.1f", {vss_opt0_3} entry = vss4, "VSS4", int, "%.1f", {vss_opt0_4} entry = vss1_ms_1, "VSS1 ms-1", int, "%.1f", {vss_opt0_1} entry = vss2_ms_1, "VSS2 ms-1", int, "%.1f", {vss_opt0_2} entry = vss3_ms_1, "VSS3 ms-1", int, "%.1f", {vss_opt0_3} entry = vss4_ms_1, "VSS4 ms-1", int, "%.1f", {vss_opt0_4} entry = economy_mpg_us, "MPG(USA)", int, "%.1f", {vss_opt0_1 && (prefSpeedUnits == 0)} entry = economy_mpg_uk, "MPG(UK)", int, "%.1f", {vss_opt0_1 && (prefSpeedUnits == 0)} entry = economy_l_100km, "l/100km", int, "%d", {vss_opt0_1 && (prefSpeedUnits == 1)} entry = ss1, "Shaft rpm 1", int, "%d", { ss_opt1 } entry = ss2, "Shaft rpm 2", int, "%d", { ss_opt2 } entry = n2o_addfuel, "Nitrous added fuel", float, "%.3f", { N2Oopt_2 } entry = nitrous1_duty, "Nitrous 1 duty", int, "%d", { N2Oopt_2 } entry = nitrous2_duty, "Nitrous 2 duty", int, "%d", { N2Oopt_2 } entry = nitrous_timer, "Nitrous Timer", float, "%.3f", { N2Oopt_2 } entry = water_duty, "Water inj duty", int, "%d", { water_freq_on } entry = als_addfuel, "ALS added fuel", float, "%.3f", { als_in_pin } entry = als_timing, "ALS timing", float, "%.1f", { als_in_pin } entry = sd_filenum, "SDcard file number", int, "%d", { log_style_on2 } entry = sd_status, "SDcard status", int, "%d", { log_style_on2 } entry = sd_phase, "SDcard phase", int, "%d", { log_style_on2 } entry = sd_error, "SDcard error", int, "%d", { log_style_on2 } entry = gear, "Gear", int, "%d", { gear_method } entry = vss1dot, "VSS1dot", float, "%.1f", {vss_opt0_1} entry = vss2dot, "VSS2dot", float, "%.1f", {vss_opt0_2} entry = accelx, "Accel X", float, "%.2f", { accXport } entry = accely, "Accel Y", float, "%.2f", { accYport } entry = accelz, "Accel Z", float, "%.2f", { accZport } entry = duty_pwm_a, "PWM A duty", int, "%d", { pwm_opt_on_a } entry = duty_pwm_b, "PWM B duty", int, "%d", { pwm_opt_on_b } entry = duty_pwm_c, "PWM C duty", int, "%d", { pwm_opt_on_c } entry = duty_pwm_d, "PWM D duty", int, "%d", { pwm_opt_on_d } entry = duty_pwm_e, "PWM E duty", int, "%d", { pwm_opt_on_e } entry = duty_pwm_f, "PWM F duty", int, "%d", { pwm_opt_on_f } entry = generic_pid_duty_a, "Generic Closed-Loop A duty", float, "%.1f", { generic_pid_flags_a_on } entry = generic_pid_duty_b, "Generic Closed-Loop B duty", float, "%.1f", { generic_pid_flags_b_on } entry = status1, "Status1", int, "%d" entry = status2, "Status2", int, "%d" entry = status3, "Status3", int, "%d" entry = status4, "Status4", int, "%d" entry = status5, "Status5", int, "%d" entry = status6, "Status6", int, "%d" entry = status7, "Status7", int, "%d" entry = status8, "Status8", int, "%d" entry = vvt_ang1, "VVT angle 1", int, "%.1f", { vvt_opt1_on } entry = vvt_ang2, "VVT angle 2", int, "%.1f", { vvt_opt1_on > 1} entry = vvt_ang3, "VVT angle 3", int, "%.1f", { vvt_opt1_on > 2} entry = vvt_ang4, "VVT angle 4", int, "%.1f", { vvt_opt1_on > 2} entry = vvt_target1, "VVT target 1", int, "%.1f", { vvt_opt1_on } entry = vvt_target2, "VVT target 2", int, "%.1f", { vvt_opt1_on > 1} entry = vvt_target3, "VVT target 3", int, "%.1f", { vvt_opt1_on > 2} entry = vvt_target4, "VVT target 4", int, "%.1f", { vvt_opt1_on > 2} entry = vvt_duty1, "VVT duty 1", int, "%.1f", { vvt_opt1_on } entry = vvt_duty2, "VVT duty 2", int, "%.1f", { vvt_opt1_on > 1} entry = vvt_duty3, "VVT duty 3", int, "%.1f", { vvt_opt1_on > 2} entry = vvt_duty4, "VVT duty 4", int, "%.1f", { vvt_opt1_on > 2} entry = tps_accel, "TPS accel", int, "%.1f", { AE_options & 0x1 } entry = map_accel, "MAP accel", int, "%.1f", { AE_options & 0x1 } entry = total_accel, "Total accel", int, "%.1f", { AE_options & 0x1 } entry = launch_timer, "Launch retard timer", float, "%.3f", { launch_opt_on && launch_opt_retard } entry = launch_retard, "Launch timed retard", float, "%.1f", { launch_opt_on && launch_opt_retard } entry = knock_cyl01, "Knock cyl# 1", float, "%.1f", {(knk_option_an == 3) && knock_conf_percyl && (nCylinders > 0)} entry = knock_cyl02, "Knock cyl# 2", float, "%.1f", {(knk_option_an == 3) && knock_conf_percyl && (nCylinders > 1)} entry = knock_cyl03, "Knock cyl# 3", float, "%.1f", {(knk_option_an == 3) && knock_conf_percyl && (nCylinders > 2)} entry = knock_cyl04, "Knock cyl# 4", float, "%.1f", {(knk_option_an == 3) && knock_conf_percyl && (nCylinders > 3)} entry = knock_cyl05, "Knock cyl# 5", float, "%.1f", {(knk_option_an == 3) && knock_conf_percyl && (nCylinders > 4)} entry = knock_cyl06, "Knock cyl# 6", float, "%.1f", {(knk_option_an == 3) && knock_conf_percyl && (nCylinders > 5)} entry = knock_cyl07, "Knock cyl# 7", float, "%.1f", {(knk_option_an == 3) && knock_conf_percyl && (nCylinders > 6)} entry = knock_cyl08, "Knock cyl# 8", float, "%.1f", {(knk_option_an == 3) && knock_conf_percyl && (nCylinders > 7)} #if CYL_12_16_SUPPORT entry = knock_cyl09, "Knock cyl#09", float, "%.1f", {(knk_option_an == 3) && knock_conf_percyl && (nCylinders > 8)} entry = knock_cyl10, "Knock cyl#10", float, "%.1f", {(knk_option_an == 3) && knock_conf_percyl && (nCylinders > 9)} entry = knock_cyl11, "Knock cyl#11", float, "%.1f", {(knk_option_an == 3) && knock_conf_percyl && (nCylinders > 10)} entry = knock_cyl12, "Knock cyl#12", float, "%.1f", {(knk_option_an == 3) && knock_conf_percyl && (nCylinders > 11)} entry = knock_cyl13, "Knock cyl#13", float, "%.1f", {(knk_option_an == 3) && knock_conf_percyl && (nCylinders > 12)} entry = knock_cyl14, "Knock cyl#14", float, "%.1f", {(knk_option_an == 3) && knock_conf_percyl && (nCylinders > 13)} entry = knock_cyl15, "Knock cyl#15", float, "%.1f", {(knk_option_an == 3) && knock_conf_percyl && (nCylinders > 14)} entry = knock_cyl16, "Knock cyl#16", float, "%.1f", {(knk_option_an == 3) && knock_conf_percyl && (nCylinders > 15)} #endif entry = porta, "porta", int, "%d" entry = portb, "portb", int, "%d" entry = porteh, "porteh", int, "%d" entry = portk, "portk", int, "%d" entry = portmj, "portmj", int, "%d" entry = portp, "portp", int, "%d" entry = portt, "portt", int, "%d" entry = cel_status, "CEL status", int, "%d" entry = cel_status2, "CEL status2", int, "%d" entry = cel_errorcode, "CEL error code", int, "%d" entry = fuel_pct, "Ethanol Percentage", float, "%.1f", { flexFuel > 0 } entry = fuelCorrection, "E85 Fuel Correction", int, "%d", { flexFuel > 0 } entry = fuel_temp1, "Fuel Temp1", float, "%.1f", { (flexFuel && (fueltemp1 == 1)) || (fueltemp1 > 15)} entry = fuel_temp2, "Fuel Temp2", float, "%.1f", { dualfuel_temp_sens } entry = fuel_press1, "Fuel Pressure1_kPa", float, "%.1f", { fp_press_in } entry = fuel_press1_psi, "Fuel Pressure1_psi", float, "%.1f", { fp_press_in } entry = fuel_press1_bar, "Fuel Pressure1_bar", float, "%.1f", { fp_press_in } entry = fuel_press2, "Fuel Pressure2_kPa", float, "%.1f", { dualfuel_press_sens } entry = fuel_press2_psi, "Fuel Pressure2_psi", float, "%.1f", { dualfuel_press_sens } entry = fuel_press2_bar, "Fuel Pressure2_bar", float, "%.1f", { dualfuel_press_sens } entry = fp_duty, "Fuel pump control duty", int, "%d", { fp_opt_mode } entry = alt_targv, "Alternator target voltage", float, "%.1f", {alternator_opt_mode > 1} entry = alt_freq, "Alternator control frequency", int, "%d", {alternator_opt_mode == 2} entry = alt_duty, "Alternator control duty", int, "%d", {alternator_opt_mode > 2} entry = load_duty, "Alternator load", int, "%d", {alternator_opt_mode && alternator_freq_monin} entry = batt_curr, "Battery current", float, "%.1f", {alternator_opt_mode && alternator_freq_currin} entry = fueltemp_cor, "Fuel temperature cor", float, "%.1f" entry = fuelpress_cor, "Fuel pressure cor", float, "%.1f" entry = ltt_cor, "Long term fuel trim cor", float, "%.1f", {ltt_opt_on} entry = gps_latdeg, "GPS Lat. deg", int, "%d", { can_poll2_gps == 1 } entry = gps_latmin, "GPS Lat. min", int, "%d", { can_poll2_gps == 1 } entry = gps_latsec, "GPS Lat. sec", float, "%.3f", { can_poll2_gps == 1 } entry = gps_londeg, "GPS Lon. deg", int, "%d", { can_poll2_gps == 1 } entry = gps_lonmin, "GPS Lon. min", int, "%d", { can_poll2_gps == 1 } entry = gps_lonsec, "GPS Lon. sec", float, "%.3f", { can_poll2_gps == 1 } entry = gps_lonEW, "GPS Lon. E/W", int, "%d", { can_poll2_gps == 1 } entry = gps_alt, "GPS Altitude", float, "%.1f", { can_poll2_gps == 1 } entry = gps_speed, "GPS Speed", float, "%.1f", { can_poll2_gps == 1 } entry = gps_speed_ms_1, "GPS Speed ms-1",float, "%.1f", { can_poll2_gps == 1 } entry = gps_course, "GPS Course (deg)", float, "%.1f", { can_poll2_gps == 1 } entry = gps_latitude, "GPS Latitude", float, "%.5f", { can_poll2_gps == 1 } entry = gps_longitude, "GPS Longitude", float, "%.5f", { can_poll2_gps == 1 } #if INTERNAL_LOG_FIELDS ;internalLogField = fieldName, class, type, offset, units, scale, translate, digits internalLogField = "Tooth number", scalar, U08, 1024, "#", 1.0, 0.0, 0 internalLogField = "Synch", scalar, U08, 1025, "", 1, 0, 0 internalLogField = "Cumulative cycles", scalar, U16, 1026, "#", 1.0, 0.0, 0 internalLogField = "Cumulative teeth", scalar, U16, 1027, "#", 1.0, 0.0, 0 internalLogField = "coilsel", scalar, U16, 1028, "", 1, 0, 0 internalLogField = "dwellsel", scalar, U16, 1029, "", 1, 0, 0 internalLogField = "PTM", scalar, U08, 1030, "", 1, 0, 0 internalLogField = "PTJ", scalar, U08, 1031, "", 1, 0, 0 internalLogField = "PTT", scalar, U08, 1032, "", 1, 0, 0 internalLogField = "PORTA", scalar, U08, 1033, "", 1, 0, 0 internalLogField = "PORTB", scalar, U08, 1034, "", 1, 0, 0 internalLogField = "next_dwell.tooth", scalar, U08, 1035, "", 1, 0, 0 internalLogField = "next_spark.tooth", scalar, U08, 1036, "", 1, 0, 0 internalLogField = "next_inj0.tooth", scalar, U08, 1037, "", 1, 0, 0 internalLogField = "next_inj1.tooth", scalar, U08, 1038, "", 1, 0, 0 internalLogField = "next_inj2.tooth", scalar, U08, 1039, "", 1, 0, 0 internalLogField = "next_inj3.tooth", scalar, U08, 1040, "", 1, 0, 0 internalLogField = "next_inj4.tooth", scalar, U08, 1041, "", 1, 0, 0 internalLogField = "next_inj5.tooth", scalar, U08, 1042, "", 1, 0, 0 internalLogField = "next_inj6.tooth", scalar, U08, 1043, "", 1, 0, 0 internalLogField = "next_inj7.tooth", scalar, U08, 1044, "", 1, 0, 0 ; internalLogField = "fuel_ovflo", scalar, U08, 1046, "", 1, 0, 0 internalLogField = "wheeldec_ovflo", scalar, U08, 1047, "", 1, 0, 0 internalLogField = "next_dwell.time32", scalar, U32, 1048, "", 1, 0, 0 internalLogField = "next_spark.time32", scalar, U32, 1049, "", 1, 0, 0 internalLogField = "TIE", scalar, U08, 1050, "", 1, 0, 0 internalLogField = "TFLG1", scalar, U08, 1051, "", 1, 0, 0 internalLogField = "TIMTIE", scalar, U08, 1052, "", 1, 0, 0 internalLogField = "TIMTFLG1", scalar, U08, 1053, "", 1, 0, 0 internalLogField = "next_inj[0].time", scalar, U16, 1054, "", 1, 0, 0 internalLogField = "next_inj[1].time", scalar, U16, 1055, "", 1, 0, 0 internalLogField = "next_inj[2].time", scalar, U16, 1056, "", 1, 0, 0 internalLogField = "next_inj[3].time", scalar, U16, 1057, "", 1, 0, 0 internalLogField = "next_inj[4].time", scalar, U16, 1058, "", 1, 0, 0 internalLogField = "next_inj[5].time", scalar, U16, 1059, "", 1, 0, 0 internalLogField = "next_inj[6].time", scalar, U16, 1060, "", 1, 0, 0 internalLogField = "next_inj[7].time", scalar, U16, 1061, "", 1, 0, 0 internalLogField = "XGSEM", scalar, U08, 1062, "", 1, 0, 0 internalLogField = "pwcalc1", scalar, U16, 1063, "", 1, 0, 0 internalLogField = "pwcalc2", scalar, U16, 1064, "", 1, 0, 0 internalLogField = "next_map_start_event.tooth", scalar, U08, 1065, "", 1, 0, 0 internalLogField = "XGCHID", scalar, U08, 1066, "", 1, 0, 0 internalLogField = "XGSWT", scalar, U08, 1067, "", 1, 0, 0 internalLogField = "xgate_deadman", scalar, U08, 1068, "", 1, 0, 0 internalLogField = "XGMCTL", scalar, U08, 1069, "", 1, 0, 0 internalLogField = "xgpc", scalar, U16, 1070, "", 1, 0, 0 internalLogField = "xgswe_count", scalar, U08, 1071, "", 1, 0, 0 internalLogField = "next_fuel", scalar, U08, 1072, "", 1, 0, 0 internalLogField = "inj1_cnt", scalar, U16, 1073, "", 1, 0, 0 internalLogField = "inj2_cnt", scalar, U16, 1074, "", 1, 0, 0 internalLogField = "inj3_cnt", scalar, U16, 1075, "", 1, 0, 0 internalLogField = "inj4_cnt", scalar, U16, 1076, "", 1, 0, 0 internalLogField = "inj5_cnt", scalar, U16, 1077, "", 1, 0, 0 internalLogField = "inj6_cnt", scalar, U16, 1078, "", 1, 0, 0 internalLogField = "inj7_cnt", scalar, U16, 1079, "", 1, 0, 0 internalLogField = "inj8_cnt", scalar, U16, 1080, "", 1, 0, 0 #endif ;-------------------------------------------------------------------------------