ETB micro progress

firmware/controllers/injector_central.cpp

@@ -36,6 +36,7 @@
 #include "settings.h"
 #include "idle_thread.h"
 #include "periodic_controller.h"
+#include "tps.h"
 
 EXTERN_ENGINE
 ;
@@ -250,8 +251,15 @@ static void handleCommandX14(uint16_t index) {
 		// cmd_test_fuel_pump
 		fuelPumpBench();
 		return;
+	case 2:
+		grabTPSIsClosed();
+		return;
+	case 3:
+		grabTPSIsWideOpen();
+		return;
 
 	}
+
 }
 
 // todo: this is probably a wrong place for this method now

firmware/controllers/sensors/tps.cpp

@@ -5,8 +5,11 @@
 #include "tps.h"
 #include "interpolation.h"
 #include "analog_input.h"
+#if EFI_PROD_CODE
+#include "settings.h"
+#endif /* EFI_PROD_CODE */
 
-	EXTERN_ENGINE;
+EXTERN_ENGINE;
 
 #if !EFI_PROD_CODE
 	static int mockTps;
@@ -127,6 +130,20 @@ int getTPS12bitAdc(DECLARE_ENGINE_PARAMETER_SIGNATURE) {
 #endif /* EFI_PROD_CODE */
 }
 
+void grabTPSIsClosed() {
+#if EFI_PROD_CODE
+	engineConfiguration->tpsMin = getTPS10bitAdc();
+	printTPSInfo();
+#endif /* EFI_PROD_CODE */
+}
+
+void grabTPSIsWideOpen() {
+#if EFI_PROD_CODE
+	engineConfiguration->tpsMax = getTPS10bitAdc();
+	printTPSInfo();
+#endif /* EFI_PROD_CODE */
+}
+
 /**
  * @brief Position on physical primary TPS
  */

firmware/controllers/sensors/tps.h

@@ -27,11 +27,14 @@ percent_t getTPS(DECLARE_ENGINE_PARAMETER_SIGNATURE);
 bool hasTpsSensor(DECLARE_ENGINE_PARAMETER_SIGNATURE);
 int convertVoltageTo10bitADC(float voltage);
 int getTPS12bitAdc(DECLARE_ENGINE_PARAMETER_SIGNATURE);
+#define getTPS10bitAdc() (getTPS12bitAdc() / TPS_TS_CONVERSION)
 float getTPSVoltage(DECLARE_ENGINE_PARAMETER_SIGNATURE);
 percent_t getTpsValue(int adc DECLARE_ENGINE_PARAMETER_SUFFIX);
 void setBosch0280750009(DECLARE_ENGINE_PARAMETER_SIGNATURE);
 void setMockTpsPosition(percent_t tpsPosition);
 void setMockPedalPosition(percent_t value);
+void grabTPSIsClosed();
+void grabTPSIsWideOpen();
 
 typedef struct {
 	efitimeus_t prevTime;

firmware/controllers/settings.cpp

@@ -408,7 +408,7 @@ static void printThermistor(const char *msg, ThermistorConf *config, ThermistorM
 	scheduleMsg(&logger, "==============================");
 }
 
-static void printTPSInfo(void) {
+void printTPSInfo(void) {
 #if EFI_PROD_CODE && HAL_USE_ADC
 	if (!hasTpsSensor()) {
 		scheduleMsg(&logger, "NO TPS SENSOR");
@@ -419,7 +419,7 @@ static void printTPSInfo(void) {
 	scheduleMsg(&logger, "tps min (closed) %d/max (full) %d v=%.2f @%s", engineConfiguration->tpsMin, engineConfiguration->tpsMax,
 			getTPSVoltage(PASS_ENGINE_PARAMETER_SIGNATURE), getPinNameByAdcChannel("tps", engineConfiguration->tpsAdcChannel, pinNameBuffer));
 #endif /* EFI_PROD_CODE */
-	scheduleMsg(&logger, "current 10bit=%d value=%.2f rate=%.2f", getTPS12bitAdc() / TPS_TS_CONVERSION, getTPS(PASS_ENGINE_PARAMETER_SIGNATURE),
+	scheduleMsg(&logger, "current 10bit=%d value=%.2f rate=%.2f", getTPS10bitAdc(), getTPS(PASS_ENGINE_PARAMETER_SIGNATURE),
 			getTpsRateOfChange());
 }
 

firmware/controllers/settings.h

@@ -16,6 +16,7 @@ void printSpiState(Logging *logger, board_configuration_s *boardConfiguration);
 void printConfiguration(const engine_configuration_s *engineConfiguration);
 void scheduleStopEngine(void);
 void setCallFromPitStop(int durationMs);
+void printTPSInfo(void);
 void setEngineType(int value);
 /**
  * See also getEngine_type_e()