diff --git a/firmware/integration/rusefi_config.txt b/firmware/integration/rusefi_config.txt
index 0f035cf6d5..cf5a6d53d1 100644
--- a/firmware/integration/rusefi_config.txt
+++ b/firmware/integration/rusefi_config.txt
@@ -680,7 +680,7 @@ float globalFuelCorrection;set global_fuel_correction X;"coef",    1,      0.0,
 
 	float adcVcc;;         "volts",    1,    0.0,       0,    6.0,        3
 	float maxKnockSubDeg;maximum total number of degrees to subtract from ignition advance\nwhen knocking;"Deg",      1,      0,       0, 100,      0
-	brain_input_pin_e[CAM_INPUTS_COUNT iterate] camInputs;+Camshaft input could be used either just for engine phase detection if your trigger shape does not include cam sensor as 'primary' channel, or it could be used for Variable Valve timing on one of the camshafts.\nTODO #660
+	brain_input_pin_e[CAM_INPUTS_COUNT iterate] camInputs;+Camshaft input could be used either just for engine phase detection if your trigger shape does not include cam sensor as 'primary' channel, or it could be used for Variable Valve timing on one of the camshafts.
 	uint8_t[CAM_INPUTS_COUNT_padding] camInputsPadding;;
 	
 struct afr_sensor_s
diff --git a/firmware/tunerstudio/rusefi.input b/firmware/tunerstudio/rusefi.input
index 981fa427c4..d569b9ec87 100644
--- a/firmware/tunerstudio/rusefi.input
+++ b/firmware/tunerstudio/rusefi.input
@@ -1823,27 +1823,31 @@ cmd_set_engine_type_default					= "@@TS_IO_TEST_COMMAND_char@@\x00\x31\x00\x00"
 	    field = "!https://rusefi.com/s/vvt"
 ; todo: code generator to hard-code all triggers not requiring VVT?
 ; todo: https://github.com/rusefi/rusefi/issues/2077
-	    field = "CAM/VVT mode shaft #1",				vvtMode1, {trigger_type != @@TT_TT_MAZDA_MIATA_NA@@}
-	    field = "VVT mode shaft #2",				    vvtMode2, {trigger_type != @@TT_TT_MAZDA_MIATA_NA@@}
-	    field = "VVT use rise front",					vvtCamSensorUseRise, {trigger_type != @@TT_TT_MAZDA_MIATA_NA@@}
-	    field = "VVT position display offset",			vvtOffset
+	    field = "Cam mode (intake cams)",				vvtMode1, {trigger_type != @@TT_TT_MAZDA_MIATA_NA@@}
+	    field = "Cam mode (exhaust cams)",				    vvtMode2, {trigger_type != @@TT_TT_MAZDA_MIATA_NA@@}
+	    field = "VVT use only rising edge",					vvtCamSensorUseRise, {trigger_type != @@TT_TT_MAZDA_MIATA_NA@@}
+	    field = "#Set offset so VVT indicates 0 degrees in default position"
+		field = "VVT offset bank 1 intake",				vvtOffset
+		;field = "VVT offset bank 1 exhaust",			vvtOffset2
+		;field = "VVT offset bank 2 intake",			vvtOffset3
+		;field = "VVT offset bank 2 exhaust",			vvtOffset4
 	    field = "print verbose VVT sync details to console",verboseVVTDecoding
 	    field = "Do not print messages in case of sync error",  silentTriggerError
 	    field = "Enable noise filtering",				useNoiselessTriggerDecoder, {trigger_type == @@TT_TT_TOOTHED_WHEEL_60_2@@ || trigger_type == @@TT_TT_TOOTHED_WHEEL_36_1@@}
 
 	dialog = triggerInputs,					"Trigger Inputs"
-		field = "!ECU reboot needed to apply these settings"
 		field = "#Cam is primary if you have cam sensor as part of trigger shape"
 		field = "Primary channel", 						triggerInputPins1
 		field = "Invert Primary",						invertPrimaryTriggerSignal
 		field = "Secondary channel", 					triggerInputPins2,            { trigger_type != @@TT_TT_TOOTHED_WHEEL@@ && trigger_type != @@TT_TT_TOOTHED_WHEEL_60_2@@ && trigger_type != @@TT_TT_TOOTHED_WHEEL_36_1@@ && trigger_type != @@TT_TT_ONE@@ && trigger_type != @@TT_TT_60_2_VW@@ && trigger_type != @@TT_TT_TOOTHED_WHEEL_36_2@@}
 		field = "Invert Secondary",				    	invertSecondaryTriggerSignal, { trigger_type != @@TT_TT_TOOTHED_WHEEL@@ && trigger_type != @@TT_TT_TOOTHED_WHEEL_60_2@@ && trigger_type != @@TT_TT_TOOTHED_WHEEL_36_1@@ && trigger_type != @@TT_TT_ONE@@ && trigger_type != @@TT_TT_60_2_VW@@ && trigger_type != @@TT_TT_TOOTHED_WHEEL_36_2@@}
-		field = "#VVT or Cam for 60/2 goes here"
-		field = "Cam Sync/VVT shaft #1 bank #1",	    camInputs1
-        field = "VVT shaft #2 bank #1",        camInputs2
-        field = "VVT shaft #1 bank #2",        camInputs3
-        field = "VVT shaft #2 bank #2",        camInputs4
-		field = "Invert Cam/VVT",                       invertCamVVTSignal
+		field = "#VVT or Cam for 60/2 goes below"
+		field = "#If your engine has no exhaust cam sensor, use intake cam inputs"
+		field = "Cam sensor bank 1 intake",	        camInputs1
+        field = "Cam sensor bank 1 exhaust",        camInputs2
+        field = "Cam sensor bank 2 intake",         camInputs3
+        field = "Cam sensor bank 2 exhaust",        camInputs4
+		field = "Invert cam inputs",                invertCamVVTSignal
 		panel = triggerInputComparator @@if_ts_show_trigger_comparator