diff --git a/firmware/tunerstudio/rusefi.ini b/firmware/tunerstudio/rusefi.ini
index ad5d6f4b85..a71be1fae3 100644
--- a/firmware/tunerstudio/rusefi.ini
+++ b/firmware/tunerstudio/rusefi.ini
@@ -1314,6 +1314,7 @@ cmd_test_idle_valve          = "w\x00\x17\x00\x01"
 		field = "use Rise Edge?",						trigger_customUseRiseEdge, {trigger_type == 0}
 		field = "needed Second Trigger Input?",			trigger_customNeedSecondTriggerInput, {trigger_type == 0}
 	dialog = triggerConfiguration_IO,	"Settings I/O"
+		field = "!ECU reboot needed to apply these settings"
 		field = "#Cam is primary if you have cam sensor"
 		field = "Primary input channel", 				triggerInputPins1
 	    field = "Secondary channel", 					triggerInputPins2
@@ -1330,6 +1331,7 @@ cmd_test_idle_valve          = "w\x00\x17\x00\x01"
 		field = "phase offset",				injectionOffset
 		
 	dialog = injIO, "Injector Output",	yAxis
+		field = "!ECU reboot needed to apply these settings"
 		field = "injection Pin Mode",       			injectionPinMode
 		field = "Injection Pin 1",						injectionPins1
 		field = "Injection Pin 2",						injectionPins2, {cylindersCount > 1}
@@ -1492,21 +1494,25 @@ cmd_test_idle_valve          = "w\x00\x17\x00\x01"
 		field = "Fan On Temperature",					fanOnTemperature
 		field = "Fan Off Temperature",					fanOffTemperature
 		field = ""
+		field = "!ECU reboot needed to apply these settings"
 		field = "Fan Pin Mode",							fanPinMode
 		field = "Fan Pin",								fanPin
 
 ;			Engine->Main Relay Settings
 	dialog = mainRealay,	"Main Relay Settings"
+		field = "!ECU reboot needed to apply these settings"
 		field = "Main Relay Mode",			         	mainRelayPinMode	
 		field = "Main Relay Pin",  						mainRelayPin
 		
 ;			Engine->Fuel Pump Settings
 	dialog = fuelPump,	"Fuel Pump Settings"
+		field = "!ECU reboot needed to apply these settings"
 		field = "Fuel Pump Pin Mode",         	        fuelPumpPinMode
 		field = "Fuel Pump Pin",						fuelPumpPin
 		
 ;			Engine->MIL Settings
 	dialog = malfunction,	"Check Engine Settings"
+		field = "!ECU reboot needed to apply these settings"
 		field = "Check Engine Pin Mode",				         	malfunctionIndicatorPinMode	
 		field = "Check Engine Pin",         						malfunctionIndicatorPin
 
@@ -1514,6 +1520,7 @@ cmd_test_idle_valve          = "w\x00\x17\x00\x01"
 	dialog = hipFunction, "HIP9011 Settings"
 		field = "Enabled",								isHip9011Enabled
 		field = "Threshold",							knockVThreshold
+		field = "!ECU reboot needed to apply these settings"
 		field = "IntHold pin (hip9011 input)",      	hip9011IntHoldPin
 		field = "ChipSelect pin",						hip9011CsPin
 		field = "hip Output/stm input",					hipOutputChannel
@@ -1523,6 +1530,7 @@ cmd_test_idle_valve          = "w\x00\x17\x00\x01"
 		panel = knockThresholdCurve
 		
 	dialog = spiFunction, "SPI settings"
+		field = "!ECU reboot needed to apply these settings"
 		field = "SPI1 MOSI",							spi1mosiPin
 		field = "SPI1 MISO",							spi1misoPin
 		field = "SPI1 SCK",								spi1sckPin
@@ -1575,6 +1583,7 @@ cmd_test_idle_valve          = "w\x00\x17\x00\x01"
 
 ;			Engine->Other inputs	
 	dialog = analogInputs, "Analog inputs"
+		field = "!ECU reboot needed to apply these settings"
 		field = "TPS ADC input", 						tpsAdcChannel
 		field = "MAF ADC input", 						mafAdcChannel
 		field = "Baro ADC input", 						baroSensor_hwChannel