60 lines
4.7 KiB
Plaintext
60 lines
4.7 KiB
Plaintext
1) RESOLVED IN R0.2 upper mounting hole does not align - see http://rusefi.com/images/Frankenso/frankenso_0_1_back.jpg
|
|
2) RESOLVED IN R0.2 add a jumper to isolate C1002 & C1003 while powered via USB? see http://rusefi.com/forum/viewtopic.php?f=4&t=569&start=50#p9859
|
|
3) RESOLVED IN R0.2 usability issue: GND test pad is under discovery
|
|
4) RESOLVED IN R0.2 add larger +5 test pad?
|
|
5) RESOLVED IN R0.2 add +12 test point?
|
|
6) RESOLVED IN R0.2 Thermocouple needs a via to allow a zip tie to go fully around the connector.
|
|
7) RESOLVED IN R0.2 op-amp reference & part # silkscreen is upside down in relation to the labeling of the actual chips
|
|
8) RESOLVED IN R0.2 Make HIP9011 components into 0805 for common parts
|
|
9) RESOLVED IN R0.2 VDD on STM discovery should be 3V not 5V.
|
|
10) RESOLVED IN R0.2 LCD mounting holes are too small for the Chinese M3 stand-offs
|
|
11) RESOLVED IN R0.2 SD card PB4 should be SO not SI PB5 should be SI not SO.
|
|
12) RESOLVED IN R0.2 USB D- and D+ were on wrong pins, D+ now on USB pin 3, TTL RX and TX were also on the wrong pins
|
|
13) RESOLVED IN R0.2 JP212 is to close to the LCD mounting slot.
|
|
14) separate VP lines of our three hi-side mosfers
|
|
15) RESOLVED IN R0.2 look into flipping the VR + and - pins
|
|
16) RESOLVED IN R0.2 add vias for GND, 12V and 5V for test purposes
|
|
17) RESOLVED IN R0.2 add option to GND one side of VR in ECU
|
|
18) RESOLVED IN R0.2 HC-OX needs 3.3V not 5V.
|
|
19) BOM issue: D1001 should be BZT52C7V5-FDICT-ND?
|
|
20) BOM issue: C1001 sch says 470uF but part number is 100uF?
|
|
21) SKQUCAA010 is End of Life. I've placed and order to get these in October, but we need a better solution
|
|
22) RESOLVED IN R0.2 JP212 should be replaced with JP209 which would be breaking the OUT9 line. That's part of hall-via-op-amp circuirty.
|
|
23) chip select and such for SPI on thermo-couple chips.
|
|
24) Change joy stick to ALPS SKRHAAE010
|
|
25) RESOLVED IN R0.2 add a prototype area for future circuits to be tossed in.
|
|
26) add a couple more low-side chips
|
|
27) RESOLVED IN R0.2 surge suppression diode option for some low-side
|
|
28) RESOLVED IN R0.2 better silkscreen for P602 & P604 - explicit "5v" "12v" "GND"
|
|
29) RESOLVED IN R0.2 Add LED indicators to injector channels.
|
|
30) RESOLVED IN R0.3 3D for C1001 bulk cap has black mark on wrong side
|
|
31) RESOLVED IN R0.3 We've moved the upper mounting hole too far - we need to move it half way back http://rusefi.com/forum/viewtopic.php?f=4&t=735#p12500
|
|
32) RESOLVED IN R0.3 C1001 should be 1mm lower to improve clearance with the case
|
|
32) Q411 should be 1.5mm lower to improve clearance with the case (See 47)
|
|
33) Q412 should be moved 3mm to the left, this would probably affect W63 which would affect the whole corner. Maybe move Q412 to the back of the board? (See 47)
|
|
34) RESOLVED IN R0.3 R0.3 rename the recently added low-side diodes and LEDs/resistors into 400 range
|
|
35) RESOLVED IN R0.3 test pads explicit silkscreen
|
|
36) RESOLVED IN R0.3 test pads on the back of the board
|
|
37) RESOLVED IN R0.3 U601/2/3: hard to see pad #1 label on the silkscreen
|
|
38) RESOLVED IN R0.3 cap values format inconsistency: C165 is ".1u", C24 C355 C471 C701 are ".1uF" and C104 C211 C291 etc are "0.1uF"
|
|
39) RESOLVED IN R0.3 rename JP212 to JP09 since it's sitting on input channel #9
|
|
40) RESOLVED IN R0.3 JP211 silkscreen not visible on rev 0.2 (was visible on rev 0.1 before the JP211 move)
|
|
41) (pedantism) eliminate the 4 unused middle pins on the LCD screen connector
|
|
42) RESOLVED IN R0.3 Wxx silkscreen on the back where it's possible - this would help while troubleshooting analog inputs
|
|
43) RESOLVED IN R0.3 vertical USB is buggered, vias are to small, ect.
|
|
44) RESOLVED IN R0.3 Move 12V injector flyback diodes to other side of W2
|
|
45) RESOLVED IN R0.3 Short out D10.
|
|
46) RESOLVED IN R0.3 add vias around ST processor. Orginal board design was a 2 layer, not it's 4 layer. It's better design practice to have GND via's closer to the GND pins.
|
|
47) Per 32) and 33) change W64,63 change to single hole, which allows U chips to move away from enclosre metal wall
|
|
48) Make hidden text for component values align such that a picture can be caputured that displays the component values.
|
|
49) check VR against 1996 Miata's.
|
|
50) HIP9011 CS line needs to be pulled down, not pulled up
|
|
51) CAN_RX line should be connected to PB12, not PD12
|
|
|
|
For honda add-on / rewiring board
|
|
-- Add 2A high side solinoid drive for VTec sol
|
|
-- Add 3rd VR chip for 3rd signal
|
|
-- Add selectable high side drive with +5V or +12V options
|
|
-- re-wire to allow freindly pinout
|
|
|