only:uaefi

firmware/config/boards/hellen/uaefi/board.mk

@@ -0,0 +1,22 @@
+# Combine the related files for a specific platform and MCU.
+
+# Target ECU board design
+BOARDCPPSRC = $(BOARD_DIR)/board_configuration.cpp
+# Set this if you want a default engine type other than normal
+ifeq ($(VAR_DEF_ENGINE_TYPE),)
+#  VAR_DEF_ENGINE_TYPE = -DDEFAULT_ENGINE_TYPE=engine_type_e::HELLEN_154_HYUNDAI_COUPE_BK2
+endif
+
+DDEFS += -DEFI_MAIN_RELAY_CONTROL=TRUE
+
+#no mux on mm100
+
+# Add them all together
+DDEFS += -DFIRMWARE_ID=\"uaefi\" $(VAR_DEF_ENGINE_TYPE)
+#DDEFS += -DEFI_SOFTWARE_KNOCK=TRUE -DSTM32_ADC_USE_ADC3=TRUE
+
+SHORT_BOARD_NAME=uaefi
+
+DDEFS += -DHELLEN_BOARD_ID_DEBUG
+
+include $(BOARDS_DIR)/hellen/hellen-common100.mk

firmware/config/boards/hellen/uaefi/board_configuration.cpp

@@ -0,0 +1,158 @@
+/**
+ * @file boards/hellen/uaefi/board_configuration.cpp
+ *
+ * See https://rusefi.com/s/uaefi
+ *
+ * @author Andrey Belomutskiy, (c) 2012-2023
+ */
+
+#include "pch.h"
+#include "defaults.h"
+#include "hellen_meta.h"
+
+static void setInjectorPins() {
+	engineConfiguration->injectionPins[0] = Gpio::MM100_INJ1;
+	engineConfiguration->injectionPins[1] = Gpio::MM100_INJ2;
+	engineConfiguration->injectionPins[2] = Gpio::MM100_INJ3;
+	engineConfiguration->injectionPins[3] = Gpio::MM100_INJ4;
+}
+
+static void setIgnitionPins() {
+	engineConfiguration->ignitionPins[0] = Gpio::MM100_IGN1;
+	engineConfiguration->ignitionPins[1] = Gpio::MM100_IGN2;
+	engineConfiguration->ignitionPins[2] = Gpio::MM100_IGN3;
+	engineConfiguration->ignitionPins[3] = Gpio::MM100_IGN4;
+}
+
+static void setupVbatt() {
+	// 4.7k high side/4.7k low side = 2.0 ratio divider
+	engineConfiguration->analogInputDividerCoefficient = 2.0f;
+
+	// set vbatt_divider 5.835
+	// 33k / 6.8k
+	engineConfiguration->vbattDividerCoeff = (33 + 6.8) / 6.8; // 5.835
+
+	// pin input +12 from Main Relay
+	engineConfiguration->vbattAdcChannel = MM100_IN_VBATT;
+
+	engineConfiguration->adcVcc = 3.29f;
+}
+
+static void setupDefaultSensorInputs() {
+    engineConfiguration->vehicleSpeedSensorInputPin = Gpio::MM100_IN_D2;
+
+	engineConfiguration->tps1_1AdcChannel = MM100_IN_TPS_ANALOG;
+	engineConfiguration->tps1_2AdcChannel = MM100_IN_O2S_ANALOG;
+
+	setPPSInputs(MM100_IN_PPS_ANALOG, MM100_IN_AUX2_ANALOG);
+
+	engineConfiguration->mafAdcChannel = EFI_ADC_NONE;
+	engineConfiguration->map.sensor.hwChannel = H144_IN_MAP1;
+
+//	engineConfiguration->afr.hwChannel = EFI_ADC_NONE;
+
+	engineConfiguration->clt.adcChannel = MM100_IN_CLT_ANALOG;
+
+	engineConfiguration->iat.adcChannel = MM100_IN_IAT_ANALOG;
+}
+
+#include "hellen_leds_100.cpp"
+
+void setBoardConfigOverrides() {
+	// rev A needs EN pin but newer revisions would potentially not use it
+	setHellenMegaEnPin();
+	setupVbatt();
+
+	setHellenSdCardSpi1();
+	configureHellenMegaAccCS2Pin();
+	configureHellenCanTerminator();
+	setHellenCan();
+
+	engineConfiguration->clt.config.bias_resistor = 4700;
+	engineConfiguration->iat.config.bias_resistor = 4700;
+
+	engineConfiguration->triggerInputPins[0] = Gpio::MM100_IN_CRANK;
+	engineConfiguration->camInputs[0] = Gpio::MM100_IN_D1;
+
+    //ETB1
+    // PWM pin
+    engineConfiguration->etbIo[0].controlPin = Gpio::MM100_OUT_PWM6;
+    // DIR pin
+	engineConfiguration->etbIo[0].directionPin1 = Gpio::MM100_SPI2_MISO;
+   	// Disable pin
+   	engineConfiguration->etbIo[0].disablePin = Gpio::MM100_SPI2_MOSI;
+   	// Unused
+ 	engineConfiguration->etbIo[0].directionPin2 = Gpio::Unassigned;
+}
+
+/**
+ * @brief   Board-specific configuration defaults.
+ *
+ * See also setDefaultEngineConfiguration
+ *
+ * @todo    Add your board-specific code, if any.
+ */
+void setBoardDefaultConfiguration() {
+	setInjectorPins();
+	setIgnitionPins();
+
+    // not override since sometimes we have issues?
+//	setHellenMMbaro();
+
+	engineConfiguration->displayLogicLevelsInEngineSniffer = true;
+
+	engineConfiguration->globalTriggerAngleOffset = 0;
+
+	engineConfiguration->enableSoftwareKnock = true;
+
+	engineConfiguration->canTxPin = Gpio::MM100_CAN_TX;
+	engineConfiguration->canRxPin = Gpio::MM100_CAN_RX;
+
+	engineConfiguration->fuelPumpPin = Gpio::MM100_OUT_PWM5;
+//	engineConfiguration->idle.solenoidPin = Gpio::H144_LS_6;
+//	engineConfiguration->fanPin = Gpio::H144_OUT_IO12;
+	engineConfiguration->mainRelayPin = Gpio::MM100_IGN8;
+//	engineConfiguration->malfunctionIndicatorPin = Gpio::H144_OUT_IO7;
+
+	// how come this is not denso 183?!
+	setCustomMap(/*lowValue*/ 11.4, /*mapLowValueVoltage*/ 0.5, /*highValue*/ 170.7, 4.8);
+
+//	engineConfiguration->brakePedalPin = Gpio::H144_IN_CAM;
+//	engineConfiguration->acRelayPin = Gpio::H144_LS_5;
+//    engineConfiguration->tachOutputPin = Gpio::H144_OUT_IO10;
+    // A/C switch on k-line
+
+	// "required" hardware is done - set some reasonable defaults
+	setupDefaultSensorInputs();
+	engineConfiguration->enableVerboseCanTx = true;
+
+	engineConfiguration->etbFunctions[0] = DC_Throttle1;
+
+	// Some sensible defaults for other options
+	setCrankOperationMode();
+
+	setAlgorithm(LM_SPEED_DENSITY);
+
+	engineConfiguration->injectorCompensationMode = ICM_FixedRailPressure;
+
+	setCommonNTCSensor(&engineConfiguration->clt, HELLEN_DEFAULT_AT_PULLUP);
+	setCommonNTCSensor(&engineConfiguration->iat, HELLEN_DEFAULT_AT_PULLUP);
+
+    setTPS1Calibration(100, 650);
+	//hellenWbo();
+}
+
+//static Gpio OUTPUTS[] = {
+//};
+
+//int getBoardMetaOutputsCount() {
+//    return efi::size(OUTPUTS);
+//}
+
+//Gpio* getBoardMetaOutputs() {
+//    return OUTPUTS;
+//}
+
+int getBoardMetaDcOutputsCount() {
+    return 2;
+}

firmware/config/boards/hellen/uaefi/compile_hellen-uaefi.sh

@@ -0,0 +1,7 @@
+#!/bin/bash
+
+
+
+
+cd ..
+bash ../common_make.sh hellen/uaefi ARCH_STM32F4

firmware/config/boards/hellen/uaefi/knock_config.h

@@ -0,0 +1 @@
+#include "../hellen_knock_config.h"