diff --git a/Hardware/Hardware.md b/Hardware/Hardware.md index da1ea5f7..68006327 100644 --- a/Hardware/Hardware.md +++ b/Hardware/Hardware.md @@ -8,8 +8,8 @@ As of March 2020 Frankenso board is sold as mostly as a DIY kit. | Board | Features | Connectors/Misc. Info | Released in | Maximum recommended engine | | ----- | -------- | --------------------- | ----------- | ---------------------------| | [Hellen](https://rusefi.com/forum/viewtopic.php?f=4&t=1682) | Coming soon! | modular design| 2020 | TBD cylinder, single electronic throttle | -| [Proteus](Proteus) | + rusEFI if you have lots of hardware or cylinders
+ 4 layer PCB, 135mm x 82.5mm
+ 16 low-side outputs, limited to 3 amps each (injectors, relays, check engine light, etc)
+ 12x ignition outputs (or general purpose 5v, 100mA push-pull)
+ Dual electronic throttles
+ 4x High-side 12v drivers, 1 amp each
+ 4 thermistor analog inputs (2.7k pull up resistor)
+ 12 General purpose analog inputs
+ Dual VR sensors (crank position, wheel speed)
+ 6 digital inputs (hall cam/crank position, wheel speed, clutch/brake switch, etc) | TE Ampseal connectors: 2x 35 pin, 1x 23 pin
rusEFI's most fully-featured shield
IP68 waterproof case | 2020 | 12 cylinder, dual electronic throttles | -| [microRusEFI](Hardware-microRusEFI) | + Available fully assembled!
+ about 10 analog inputs
+ One VR/Hall input channel for crank sensor
+ One Hall input channel for crank sensor
+ 4 injector output channels
+ 4 logic level coil control channels (external igniters could be needed for some coils) | 48-pin connector
On-board DBW
USB, CAN
open source hardware | 2019 | 4 cylinder, single electronic throttle | +| [Proteus](Proteus) [ on eBay!](https://www.ebay.com/itm/rusEFI-Proteus-0-4-standalone-ECU/333841923141)| + rusEFI if you have lots of hardware or cylinders
+ 4 layer PCB, 135mm x 82.5mm
+ 16 low-side outputs, limited to 3 amps each (injectors, relays, check engine light, etc)
+ 12x ignition outputs (or general purpose 5v, 100mA push-pull)
+ Dual electronic throttles
+ 4x High-side 12v drivers, 1 amp each
+ 4 thermistor analog inputs (2.7k pull up resistor)
+ 12 General purpose analog inputs
+ Dual VR sensors (crank position, wheel speed)
+ 6 digital inputs (hall cam/crank position, wheel speed, clutch/brake switch, etc) | TE Ampseal connectors: 2x 35 pin, 1x 23 pin
rusEFI's most fully-featured shield
IP68 waterproof case | 2020 | 12 cylinder, dual electronic throttles | +| [microRusEFI](Hardware-microRusEFI) [on eBay!](https://www.ebay.com/itm/333532119947) | + Available fully assembled!
+ about 10 analog inputs
+ One VR/Hall input channel for crank sensor
+ One Hall input channel for crank sensor
+ 4 injector output channels
+ 4 logic level coil control channels (external igniters could be needed for some coils) | 48-pin connector
On-board DBW
USB, CAN
open source hardware | 2019 | 4 cylinder, single electronic throttle | | [Prometheus](https://rusefi.com/forum/viewtopic.php?f=4&t=1215) | + The only rusEFI board with on-board wide band controller.
+ compact 4-layer PCB smaller than 93 x 100 mm
+ on-board power supply
+ knock sensor chip
+ stepper motor IAC controller chip
+ stepper motor IAC controller chip
+ onboard 4-channel "smart" protected ignition drivers
+ bluetooth module
+ supports two packages of on-board stm32 chips | no on-board connector (wired)
SD card, USB/TTL, CAN | 2017 | 4 cylinder. No plans to offer assembled units. | | [Frankenstein](https://rusefi.com/forum/viewtopic.php?f=4&t=359) retired | + Simplest rusEFI board
+ our smaller two-layer board
+ Small Box shipping rate
+ low price
- external 5v power supply required
- external brain board required | no on-board connector (wired)
SD card, USB/TTL, CAN
open source hardware | 2014 | Flexible - probably 8 cylinder max recommended. No plans to offer assembled units. | | [Frankenso](Hardware-Frankenso) retired| + Most customizable board
+ larger 154x152mm 4-layer board requires a Medium Box shipping rate
+ on-board power supply
+ 20x4 LCD screen
+ joystick
+ works both with external brain boards and on-board stm32 chip
+ knock sensor chip
+ used Denso OEM cases available | on-board 64 pin connector
SD card, USB/TTL, CAN
open source hardware | 2014 | Flexible - probably 8 cylinder max recommended |