Update Dev-Status.md (#477)
* Update Dev-Status.md * Update Dev-Status.md
This commit is contained in:
mi-hol
GitHub
parent
7c3e1a4dbc
commit
5e269e4c9a
|
|
@ -37,6 +37,8 @@ Base Engine Settings
|
|||
(🔶): MAF fuel strategy
|
||||
(💚): Firing orders
|
||||
(💚): RPM limit
|
||||
(🔶): Configurable hard cut RPM limit
|
||||
(🔶): Variable RPM limit based on CLT
|
||||
(💚): Boost Limit
|
||||
|
||||
Trigger [**988** documentation issue](https://github.com/rusefi/rusefi/issues/988)
|
||||
|
|
@ -86,13 +88,15 @@ Injection settings [**1041**](https://github.com/rusefi/rusefi/issues/1041)
|
|||
(💚): Simultaneous fuel mode
|
||||
(💚): Configurable Injector output pins
|
||||
(🔶): Single point fuel mode
|
||||
(🔶): Per cylinder fuel trim
|
||||
(🔶): Per cylinder fuel trim
|
||||
(🔶): Flex fuel sensor
|
||||
|
||||
Injector dead time
|
||||
(🔶): Injection dead time (latency) compensation [**275**](https://github.com/rusefi/rusefi/issues/275)
|
||||
|
||||
Fuel short-term closed-loop correction
|
||||
(🔶): Short term fuel trim enable/disable [**384**](https://github.com/rusefi/rusefi/issues/384)
|
||||
(🔶): Closed loop fueling
|
||||
CLT thresholds
|
||||
RPM thresholds
|
||||
EGO thresholds
|
||||
|
|
@ -172,6 +176,7 @@ Cranking
|
|||
|
||||
Cranking Settings [**285**](https://github.com/rusefi/rusefi/issues/285) [**314**](https://github.com/rusefi/rusefi/issues/314)
|
||||
(💚): Configurable cranking speed limit
|
||||
(🔴): Instant crank speed
|
||||
(💚): Flood clear
|
||||
(💚): Faster engine start mode (a smarter cranking logic)
|
||||
(💚): Temperature configurable fuel priming pulse
|
||||
|
|
@ -209,6 +214,7 @@ Idle settings
|
|||
(🔶): Extra IAC demand above x% throttle at idle
|
||||
(💚): Manual IAC position (open loop)
|
||||
(🔶): Idle PID controller [**501**](https://github.com/rusefi/rusefi/issues/501)
|
||||
(🔶): Idle switch style TPS support
|
||||
|
||||
Idle hardware
|
||||
(🔶): Stepper Idle [**351**](https://github.com/rusefi/rusefi/issues/351) [**1088**](https://github.com/rusefi/rusefi/issues/1088) [**1395**](https://github.com/rusefi/rusefi/issues/1391)
|
||||
|
|
@ -331,10 +337,10 @@ EGO sensor
|
|||
(💚): Calibration drift correction value
|
||||
|
||||
Narrow to Wideband approximation
|
||||
(🔴): Narrow to wideband approximation table
|
||||
(🔶): Narrow to wideband approximation table
|
||||
|
||||
CJ125 Settings (wbo decoder)
|
||||
(🔴): CJ125 (Bosch wide band controller) enable/disable [**1460**](https://github.com/rusefi/rusefi/issues/1460)
|
||||
(🔴): CJ125 (Bosch wide band controller) enable/disable [**1460**](https://github.com/rusefi/rusefi/issues/1460)
|
||||
(🔴): LSU4.9 sensor select [**1460**](https://github.com/rusefi/rusefi/issues/1460)
|
||||
(🔴): CJ125 chip select pin [**1460**](https://github.com/rusefi/rusefi/issues/1460)
|
||||
(🔴): CJ125 chip select mode [**1460**](https://github.com/rusefi/rusefi/issues/1460)
|
||||
|
|
@ -351,7 +357,7 @@ Oil pressure
|
|||
(🔶): 2 point oil pressure sensor calibration
|
||||
|
||||
EGT inputs
|
||||
(🔴): SPI select for EGT via SPI
|
||||
(🔶): SPI select for EGT via SPI
|
||||
(🔴): 8x EGT inputs [**149**](https://github.com/rusefi/rusefi/issues/149)
|
||||
|
||||
---
|
||||
|
|
@ -369,6 +375,7 @@ Engine chart size
|
|||
Data logging Settings
|
||||
(💚): Debug logging enable setting
|
||||
(💚): Error logging enable setting
|
||||
(🔶): Race capture integration
|
||||
|
||||
Bench Test and Commands
|
||||
(💚): 8 coil spark bench test
|
||||
|
|
@ -479,15 +486,15 @@ TLE8888 pin config
|
|||
Aux serial pin config
|
||||
|
||||
Experimental or Broken
|
||||
(🔴): Global fuel correction coefficient
|
||||
(🔴): Ignition math logic
|
||||
(🔶): Global fuel correction coefficient
|
||||
(🔶): Ignition math logic
|
||||
(🔶): MAP averaging logic
|
||||
|
||||
Multispark
|
||||
(🔶): Enable/disable multi spark [**327**](https://github.com/rusefi/rusefi/issues/327)
|
||||
(🔶): Multi spark config
|
||||
|
||||
GDI Dreams see [GDI-status](GDI-status)
|
||||
GDI Dreams see [GDI-status](GDI-status)
|
||||
(🔴): MC33816_cs GDI config [**1448**](https://github.com/rusefi/rusefi/issues/1448)
|
||||
|
||||
HIP9011 Settings (knock decoder)
|
||||
|
|
@ -499,7 +506,7 @@ Electronic Throttle Body (beta)
|
|||
(🔶): Disable ETB drive motor
|
||||
(🔶): H-bridge configuration
|
||||
(🔶): ETB idle settings
|
||||
(🔶): ETB PID settings
|
||||
(🔶): ETB PID settings
|
||||
(🔶): ETB autotune
|
||||
(🔶): TPS auto calibrate
|
||||
|
||||
|
|
@ -510,10 +517,10 @@ ETB Pedal to TPS
|
|||
(🔶): 8x8 ETB pedal transfer map
|
||||
|
||||
Launch Control Settings
|
||||
(🔴): Launch control [**203**](https://github.com/rusefi/rusefi/issues/203)
|
||||
(🔴): Launch control
|
||||
|
||||
Rolling Launch Settings
|
||||
(🔴): Rolling launch [**203**](https://github.com/rusefi/rusefi/issues/203)
|
||||
(🔴): Rolling launch
|
||||
|
||||
AntiLag Settings
|
||||
(🔶): Anti lag
|
||||
|
|
@ -528,22 +535,16 @@ The title is a little developer joke, see [here](https://en.wikipedia.org/wiki/L
|
|||
(🔴): Infinite variable VVT ```[Tickets held with the simple VVT entry]()```
|
||||
(🔴): Auto tune injector dead times [**492**](https://github.com/rusefi/rusefi/issues/492)
|
||||
(🔴): Trigger pattern auto detect [**418**](https://github.com/rusefi/rusefi/issues/418)
|
||||
(🔴): Flex fuel sensor [**540**](https://github.com/rusefi/rusefi/issues/540)
|
||||
(🔴): Multiple crank pattern sync [**679**](https://github.com/rusefi/rusefi/issues/679)
|
||||
(🔴): Fuel consumption [**45**](https://github.com/rusefi/rusefi/issues/45)
|
||||
(🔴): Per injector performance correction [**95**](https://github.com/rusefi/rusefi/issues/95)
|
||||
(🔴): Instant crank speed [**135**](https://github.com/rusefi/rusefi/issues/135) [**343**](https://github.com/rusefi/rusefi/issues/343) [**329**](https://github.com/rusefi/rusefi/issues/329) [**936**](https://github.com/rusefi/rusefi/issues/936)
|
||||
(🔴): Configurable hard cut RPM limit [**192**](https://github.com/rusefi/rusefi/issues/192)
|
||||
(🔴): Idle switch style TPS support [**209**](https://github.com/rusefi/rusefi/issues/209)
|
||||
(🔴): Smart ECU: misfire detection on running engine [**936**](https://github.com/rusefi/rusefi/issues/936)
|
||||
(🔶): Configurable hard cut RPM limit
|
||||
(🔴): On ECU autotune [**247**](https://github.com/rusefi/rusefi/issues/247)
|
||||
(🔴): Dual fuel maps [**289**](https://github.com/rusefi/rusefi/issues/289)
|
||||
(🔴): Built in Timing Light [**297**](https://github.com/rusefi/rusefi/issues/297)
|
||||
(🔴): Fan control RPM limit [**310**](https://github.com/rusefi/rusefi/issues/310)
|
||||
(🔴): Closed loop fueling [**357**](https://github.com/rusefi/rusefi/issues/355) [**384**](https://github.com/rusefi/rusefi/issues/369)
|
||||
(🔴): Trigger pattern auto detect [**418**](https://github.com/rusefi/rusefi/issues/418)
|
||||
(🔴): Variable RPM limit based on CLT [**455**](https://github.com/rusefi/rusefi/issues/455)
|
||||
(🔴): Limp mode [**468**](https://github.com/rusefi/rusefi/issues/468)
|
||||
(🔴): Yaw rate sensor support [**613**](https://github.com/rusefi/rusefi/issues/613) [**932**](https://github.com/rusefi/rusefi/issues/932)
|
||||
(🔴): Race capture integration [**1163**](https://github.com/rusefi/rusefi/issues/1163)
|
||||
(🔴): Transmission control [**1454**](https://github.com/rusefi/rusefi/issues/1454)
|
||||
(🔴):
|
||||
|
|
|
|||
Loading…
Reference in New Issue