Merge remote-tracking branch 'remotes/origin/master' into non_wik_master

Hardware/Hardware.md

@@ -1,13 +1,16 @@
 rusEfi runs on wide array of boards with stm32f4 and stm32f7 microcontrollers.
 
-As of June 2019 only Frankenso board is sold completely assembled with case.
+As of March 2020 microRusEfi is is sold as completely ready to run ECU or as a pre-assmbled 80% complete kit.
+
+As of March 2020 Frankenso board is sold as mostly as a DIY kit.
 
 | Board | Features | Released in |
 | ------------- | ------------- | ---- |
 | [Frankenso](https://rusefi.com/forum/viewtopic.php?f=4&t=569) | Most customizable board | 2014 |
 | [Prometheus](https://rusefi.com/forum/viewtopic.php?f=4&t=1215)  | The only rusEfi board with on-board wide band controller  | 2017 |
 | [Frankenstein](https://rusefi.com/forum/viewtopic.php?f=4&t=359)  | Simplest rusEfi board | 2014 |
-| [microRusEfi](https://rusefi.com/forum/viewtopic.php?f=4&t=1538) | coming soon! | 2019 |
+| [microRusEfi](https://rusefi.com/microrusefi) | Available fully assembled! | 2019 |
+| [Helen](https://rusefi.com/forum/viewtopic.php?f=4&t=1682) | Coming soon! | 2020 |
 
 
-For more information see https://rusefi.com/wiki/index.php?title=Hardware:For_Sale
+For more information see https://rusefi.com/wiki/index.php?title=Hardware:Boards_Comparison

Hardware/microrusefi/Hardware_microRusEfi.md

@@ -1,6 +1,7 @@
 microRusEfi is a highly integrated board for rusEfi ECU. microRusEfi is targeted at port injected
 gasoline engines with one, two, three or four cylinders. microRusEfi has means to control electronic throttle body.
 
+[Connector Pinout](Hardware_microRusEfi_wiring)
 
 microRusEfi latest schematics is available at https://github.com/rusefi/hw_microRusEfi/blob/master/microRusEfi_Schematic.pdf
 
@@ -8,16 +9,22 @@ microRusEfi latest schematics is available at https://github.com/rusefi/hw_micro
 
 Complete set of board source files is available at https://github.com/rusefi/hw_microRusEfi
 
-Board overview:
-- about 10 analog inputs
-- One VR/Hall input channel for crank sensor
-- One Hall input channel for crank sensor
-- 4 injector output channels
-- 4 logic level coil control channels (external igniters could be needed for some coils)
-- USB
-- CAN
+# Capabilities
+* Primary VR or Hall input (configurable with few resistor changes)
+* Secondary Hall input
+* x4 analog thermistor (temperature) inputs
+* x10 analog voltage inputs (0-5v)
+* x4 high-Z injector outputs
+* x2 high-current low side outputs for IAC/VVT/other solenoids
+* Dedicated main relay control output 
+* x4 low-current low side outputs for relays or warning lights 
+* x4 5v logic-level ignition outputs
+* x2 5v/12v configurable logic level outputs (requires resistor changes)
+* Electronic throttle body (drive by wire)
+* CAN connectivity on the plug
+* USB connectivity on the plug 
 
+[Connector Pinout](Hardware_microRusEfi_wiring)
 
-For wiring see [rusEfi wiring](Hardware_microRusEfi_wiring)
 
 ![microRusEfi image](Hardware/microrusefi/Hardware_microRusEfi_0_1_pcb.jpg)

Hardware/microrusefi/Hardware_microRusEfi_wiring.md

@@ -1,13 +1,13 @@
 # Connector Pinout
 
-<mark>insert connector image/pins here</mark>
+![connector](Hardware/microrusefi/Hardware_microRusEfi_connector.png)
+
+![microRusEfi photo](Hardware/microrusefi/Hardware_microRusEfi_connector.jpg)
 
 Rear side of PCB
 
 ![microRusEfi image](Hardware/microrusefi/Hardware_microRusEfi_0_3_PCB_pinout.png)
 
-![microRusEfi photo](Hardware/microrusefi/Hardware_microRusEfi_connector.jpg)
-
 # Pin Descriptions
 
 Each pin has a *Type ID*, which can be used to look up in the following tables what the pin is for, and what functions it can perform.
@@ -107,11 +107,12 @@ These tables provide technical information about the different types of pin foun
 | can | CAN bus | CAN communication
 
 USB cable green wire: USB D+ DATA+
-USB cable white wire: USB D- DATA-
-USB cable black wire: ground
-USB cable red wire: +5v (would not work via microRusEfi connector)
 
-![connector](Hardware/microrusefi/Hardware_microRusEfi_connector.png)
+USB cable white wire: USB D- DATA-
+
+USB cable black wire: ground
+
+USB cable red wire: +5v (would not work via microRusEfi connector)
 
 ## Hall type Crank sensor